Search Documents

By Hector Simchas

"1. BENTONITE: THE CRUCIAL CONSTITUENT OF SLURRYSuspensions of bentonite and water are used in a variety of applications in underground engineering. For the construction of underground elements like slurry walls or piles, bentonite slurries offer support to the excavation of loose soils and counter pressure against hydrostatic pressure of ground water, especially where soil permeability is high. In addition, for the construction of tunnels by the slurry-shield method or when hydromills are used for excavation, bentonite suspensions transfer the loosened soil to the surface. In applications like pipe jacking and microtunneling, or where high revolution drilling is required, bentonite also provides lubrication and cooling.To fulfill these functions, the properties of a bentonite slurry need to remain stable, or at least predictable, during the course of construction. Unfortunately, when a suspension mixes with earth, ground water and/or impurities, its properties may be compromised resulting to reduced performance, which would in turn lead to increased construction costs and the risk of the excavation collapsing. Our experience in the lab and onsite is presented herewith.2. MOST USUAL FACTORS OF PERFORMANCE FAILUREWater and soil quality are important factors defining the behavior of suspensions. In an extensive program of measurements in our technical laboratory, the effect of frequently encountered harmful substances on bentonite suspensions has been examined and the results are summarised in Table 1.Some tests show that the conductivity of water has a direct relationship with Marsh Viscosity. For example, we have seen that if the quantity of bentonite required to achieve a 40s Marsh Time ranges between 50-52 kg/m3 at water conductivity below 100 µS/cm; when conductivity is increased to 1,400 µS/cm, we need 65-68 kg/m3 in order to achieve the same property."

Jan 1, 2015

By P. M. Deshpande

An interactive short column system is evolved as alternative to deep foundation system in deep layers of marine clay, the interaction of encased stone column and marine clay carry load without causing conventional settlement. This paper presents concept of the system and its field application as foundation of culverts on marine clay layer of 15 to 17 M underlain by residual soil layer of 5 to 6 M, where conventional pile of 23 to 25 M would have been required.

Jan 1, 1996

By S. Y. Zhou

Excavation with earth retaining is one of the main technological means in deep foundations and underground engineerings. Several construction methods which have been used in China are introduced here with some examples from engineering practices in Shanghai, including foundation pit protected by steel or RC sheet piling or D-walls, open caissons and pneumatic caissons, shield tunnel and pipe jacking, etc. This paper also discusses the prospect in development and utilization of underground space in China and the challenge to which the engineers specialized in deep foundations have to face.

Jan 1, 2010

By Jack Hayes

Vibrating wire strain gages have proven to be a very reliable and effective tool for the measurement of strains associated with the loading of bored piles (drilled shafts). However, when these strains are used to calculate the load, or stresses in the pile, the results can sometimes be confusing and/or difficult to interpret. This paper describes some of these situations, using examples from actual case histories, and discusses some of the difficulties associated with residual load effects, curing and temperature induced strains, load stress distribution effects, estimated modulus and area.

Jan 1, 2002

By Arvindh Gupta

BC Hydro proposed to improve the stability of the existing Seven Mile Dam with 54 corrosion protected, re-stressable anchors comprising 92/0.6? strands each, in phase 2 of the program. Being globally the largest capacity anchors ever build, coupled with extra ordinary specifications, the project was a challenge for the entire post tensioning industry. The paper discusses the challenges associated with the anchor material supply as per specifications, extensive research and development carried out by Con-Tech Systems ltd. to overcome the challenges and contribute in making the project a success. The substance of this article is published in the Aug/Sep issue of ADSC magazine.

Jan 1, 2004

By L. Z. Xie

The results of the experimental study on the static behavior of single piles subjected to repeated and reciprocating axial loadings are recommended in this paper. Tests of four full-scale single piles of two different lengths under repeated loading and those under reciprocating loading have been conducted using the slow maintained load test method. All the eight piles were instrumented with strain gages located along the shafts. The study showed that for repeated loads below a certain critical value the total displacement of the pile top approached gradually a constant value. However, any repeated load greater than the critical value resulted a residual displacement per cycle, and that the reciprocating load capacity of a pile was dependent on the ultimate bearing capacity of the pile in tension and both were in the direct ratio.

Jan 1, 2010

By Subhash B. Bhide

Deep foundations are affected by the presence of sulphates, chlorides, organic contents and water currents present in the soil. The sulphates in soil and ground water interfere first with setting of concrete. In long term, growing of sulphate crystals in concrete, crevices can spall the concrete. The chlorides mainly affect the steel. The organic content does not allow the concrete to set. It also reduces the compressive strength of concrete. The frequency and methods of sampling and testing for above corrosive elements are discussed. Presently available methods to avoid attack due to these corrosive elements are discussed. The stipulations by various codes are summarised. A method to assess the short term impact is elaborated with results of field studies. A tool developed to study the presence and effects of underground water currents on concrete is also discussed.

Jan 1, 1996

By John R. Davie

This paper describes the design and construction of two 5.6 MN capacity drilled piers installed to support the main loading elements of a large cantilevered gantry crane. The critical crane columns were located within and at the edge of an existing sheet-pile cofferdam, which had been filled with loose coal slag when it was originally constructed Due to the presence of the slag and the age and questionable condition of the sheet-piles, the drilled piers were installed to provide vertical and lateral supports for these columns. The lateral capacity of the piers was supplemented by two smaller drilled piers and two large spread footings that were linked by a system of grade beams.

Jan 1, 2006

By Emad Farouz, Roger Failmezger

"The proposed reconstruction of I-75 downtown consists of widening an approximately 2.46 Km section of IR-75 through the northern section of downtown Dayton, OH, USA. Bridge B-13 is a 9-span continuos prestressed concrete I-beam, 319.0-meter (1,048-foot) long bridge with a stub abutment on MSE walls for the rear abutment, and a stub abutment with spill-through slopes for the forward abutment. The piers in the river were located parallel to the Great Miami River, and are full-height reinforced concrete wallsPRESSUREMETER TEST PROCEDUREThe driller advanced either casing or augers approximately 1 meter above the pressuremeter test. Steel casing was used to advance borings performed in the river, and augers were used for borings on land. Mud rotary drilling with a large diameter roller bit was used to remove all of the gravel and cobble fragments inside the casing or augers.At the pressuremeter test elevation the driller used a 63.5-mm (2.5-inch) carbide button bi-cone bit, using a rotation rate of about 60 rpm, a mud fl ow rate of about 10 gallons per minute (40 liters per minute), and an advance rate of 6 to 10 minutes per meter (2 to 3 minutes per foot). To minimize vibrations, advance rates were slower where excessive cobbles were encountered. The 63.5-mm (2.5-inch) O.D. slotted casing pressuremeter was lowered to the test elevation, often requiring either pushing or hammering into the test zone. We believe that the test zone was not perfectly straight, or that gravel or cobble fragments jutted into the test zone and had to be displaced to advance the pressuremeter into the test zone. The slotted casing prevented membrane damage during insertion. A photograph of the slotted casing being lowered into the borehole is shown below.The pressuremeter was calibrated for system compressibility and membrane resistance. At full expansion of 800 cm3, the membrane resistance of the slotted casing was about 2.5 bars.Strain-controlled tests were performed using a Texam control unit with a monocell probe. Volume increments of 20 cm3 were injected into the probe and corresponding pressures were measured. Near the end of the elastic portion of the test, an unload-reload cycle was done. A creep test was performed for 10 minutes at the next volume increment. The test continued until either 800 cm3 were injected or the membrane burst."

Jan 1, 2007

By Shenbaga R. Kaniraj

The pile loading tests are generally conducted to assess the safe load on piles in compression. In the Indian practice, the safe load is determined using the pile loading test data and the two criteria specified in the Indian Standard Code, IS.2911 (Part 4) -1985. For this, the test pile should have undergone a minimum displacement equal to 10% of the pile diameter. Often, the piles are not subjected loads that are sufficient to cause a displacement of this magnitude. If the settlement is at least 12 mm, then the safe load is determined based only on the first criterion. But, if the settlement is less than 12 mm, the safe load cannot be determined using the IS Code criteria. The paper presents two procedures called hyperbolic and generalized hyperbolic methods to estimate the safe load using the IS Code criteria even when the loading test data is insufficient. The data from two initial tests have been analyzed. The predicted safe loads have been compared with the actual safe loads.

Jan 1, 1996

By Emad Farouz

This paper compares the predicted axial capacity of driven Pre-cast Pre-stressed Concrete (PPC) piles for the Lake Gaston Water Treatment Plant (LGWTP) using several design methodologies versus the axial capacity measured from dynamic and static load testing. The LGWTP site is located in Chesapeake, Virginia and is part of the Great Dismal Swamp. The subsurface investigation included soil borings, in-situ dilatometer (DMT) tests, and in-situ piezocone (CPTu) tests. The axial capacity predictions of the PPC piles were performed using the computer programs DRIVEN and FB-DEEP which are based on SPT N-values. Additionally, an empirical method proposed by Martin, et al. (1987) based on local experience with PPC pile design in the Yorktown formation in the Tidewater area of Virginia was also evaluated. Finally, the ?Laboratoire Central des Ponts et Chausées (LCPC)? method developed by Bustamante and Gianeselli (1982) based on CPT measurements was also used to develop the axial pile capacity of the piles. This paper shows that the FB-DEEP computer program and the LCPC method provided a reasonably good prediction of the pile axial capacity measured from PDA, CAPWAP, and Static Load Tests in comparison with the other design methods used. The soils in this area develop significant setup over time and it was found that FB-DEEP and the LCPC method are capable of incorporating this setup in the prediction of the long-term axial capacity of driven piles in this area.

Jan 1, 2007

By Kam Ng

For bridges or buildings that may be subjected to large vertical and lateral loads, drilled shafts offer an economic foundation solution. While the current drilled shaft design practice is considered adequate, introducing a performance-based approach to designing the drilled shafts will make their design more cost-effective and produce more dependable response. This concept was examined using analysis of 41 drilled shaft load test data from several states. This process identified the challenge with the lack of information from the Osterberg (O-cell) load test method to characterize the full top load-displacement response. When a typical single O-cell is utilized in a drilled shaft test, depending on the location of the O-cell and the geomaterials present along and beneath the shaft, the load test result typically quantifies either the side resistance or end bearing reaching the ultimate load-displacement curve but not both components. This limitation hinders the determination of a suitable shaft resistance as a function of a target top displacement. To overcome this challenge, an improved procedure is proposed for establishing the full load-displacement curve based on data gathered from one O-cell. The method will be presented in the paper for three different cases (i.e., side resistance reaches the ultimate during the test, end bearing reaches the ultimate during the test, and neither components reach the ultimate values). Because it allows the characterization of the full load-displacement curve, the proposed procedure will allow performance-based design of drilled shafts with due consideration to settlement while satisfying the Load and Resistance Factor Design.

Jan 1, 2013

By John A. Egan, Nathaniel Wagner, Micaela Largent, Jonathan P. Stewart, Debra Murphy, Jeremy Butkovich

The Millennium Tower is a 58-story reinforced concrete building that was constructed in San Francisco, California between 2005 and 2009. The Tower is founded on an embedded pile supported mat with pile tips bearing in dense marine deposits that overlie an over-consolidated marine clay layer known locally as Old Bay Clay. This clay layer experienced stress increases from Tower self-weight and from multiple episodes of de-watering between 2006 and 2018 at the Tower site and neighboring sites. Settlements of the Tower foundation have been measured since 2006 and lateral deflections of the Tower have been inferred and measured since 2009. Available information on this case history include geotechnical site conditions and data from a monitoring program that tracked foundation settlements, Tower tilt, groundwater levels at the Tower site, and ground inclinations over time. This presentation will discuss the ground deformation mechanisms that caused the observed movements, the degree to which the movements can be predicted, and lessons from this case history for the design of deep foundations for tall buildings in San Francisco and geologically similar regions.

Sep 8, 2021

By Michal Topolnicki

Deep Mixing Series: This article is the second keynote highlighted from DFI's virtual Deep Mixing Conference in 2021, for which Topolnicki served as a committeee co-chair Polish applications of deep soil mixing (DSM) technology occupy a leading position in Europe. That includes use for road and railway embankments, bridges, residential and industrial build- ings, silos, commercial centers, slabs, car parks and storage yards, excavation supports and cut-off walls. In fact, more than 350 road and railway viaducts and 200 wind turbines have been founded nationally on DSM columns, which are firsts on an international scale. This represents more than 1,200 imple- mentations by the Polish geotechnical industry. Considering the need to update DSM design recommendations, this article will attempt to summarize the best practices of wet DSM design and implementation, in particular. It draws on 20 years of experience and will high- light the properties and principles of the design of stabilized soil and lessons learned. Case studies are included to fur- ther understanding of the careful con- siderations needed with this technology.

Apr 1, 2022

By Georgette Hlepas

How often phrases like these have been made by project managers and project teams trying to explain why there has been cost growth, project delays and differing site conditions claims. But does it really take x-ray vision? Do we really approach geotechnical construction projects unprepared for the subsurface that may be encountered because we can't get the answer? Too often our industry seems to think the answer is, "yes." However, this is not because we can't understand the subsurface. All too frequently it is because a choice is made to save money or time by foregoing or shortchanging upfront subsurface investigations. This is accepting a risk at the beginning of the process and realizing it during construction. Case histories have proven time and time again that upfront investment in site exploration and constructing a ground model mitigates risk in design and construction. But how much do we prepare? What level of investigation (or investment) is appropriate? The answer of course, is it depends; how much risk are you willing to take for your project and what are the potential consequences?

May 1, 2022

By Bengt H. Fellenius

An upgrading and straightening of a highway included building a bridge across a small river. A routine site investigation was initiated to determine the conditions for designing the foundation of the bridge. The proposed bridge was a two-lane highway bridge in one span with a total length of 30 m (100 ft), as indicated in Fig. 1. It was to be placed about 20 m (66 ft) upstreams of the bridge for the existing highway. The site investigation included one boring at each abutment with soil sampling and in-situ vane testing and placed about halfway up the slope from the small river at ground surface elevation + 54 m. Within the investigated maximum depth of 40 m (130 ft), the soils at both borehole locations consisted of a thin clay crust over a thick deposit of soft sensitive clay with a natural water content of about 70 % and a liquid limit of about 60. The undrained shear strength below the crust was about 20 KPa (400 psf) and increased slightly with depth. The sensitivity was high, about 40.

Jan 1, 1987

By Andrew Pontecorvo, Steven Lowe, David Sposito

Buildings with large height-to-width ratios require foundations with significant uplift resistance. This paper presents a case study of the permanent rock tiedowns installed for One Manhattan West, a sixty-seven-story office building in midtown Manhattan. Site access and schedule dictated the size of the equipment for installing the tiedowns would be limited to drilling a 16 inch (406 mm) diameter hole. A three bar configuration of 3 inch (76 mm) diameter high strength threaded bars was chosen to develop an allowable capacity of 923 tons (4060 kN) per tiedown. Although the quality of the rock at the site was generally high, a challenging geologic condition emerged during the installation of one of the tiedowns requiring a creative installation procedure. Although the three bar configuration performed relatively well there are challenges with loading and testing this bar arrangement. Unlike single bar tiedowns that are typically tested with a high success rate, testing of a multiple bar system can result in some unsatisfactory results. This may be attributed to the installation challenges, difficulty loading each bar uniformly and/or the method of monitoring the test. Understanding the complexities is necessary to improve the testing results and achieve similar reliabilities of single bar systems.

By Travis A. Shoemaker, Mitchell S. Youmans, Nancy T. Chin, Michael S. Senior

A geologic assessment and stability analysis of the right abutment of Boundary Hydroelectric Dam in Pend Oreille County, Washington was completed in May 2017. The stability analyses identified a potential failure plane of a rock block that supports a bridge abutment, and weight restrictions were established to reduce the bridge loads. To restore full use of the bridge, a long-term stabilization solution was designed. A two-phased construction approach was implemented to reduce risk: (1) cable lashing and wire mesh and (2) 24 permanent post-tensioned tiebacks. The tiebacks were located and sequenced based on stabilization effect and site access to incrementally ease the bridge loading restrictions throughout construction. Due to weight restrictions and site tolerances, all work was performed with rope access construction methods. The contractor’s means and methods, tight drilling tolerances, and an exploratory adit within the rock block made the construction uniquely challenging. Due to limited exploratory data and irregular rock face geometries, the design orientation, location, and tolerances of the tiebacks were established in a 3D Building Information Model (BIM). The 3D model was revised frequently during construction to 1) model the as-drilled conditions of the tiebacks; 2) compare with the remaining proposed anchors; 3) anticipate the contractor’s sequence to reduce risk during drilling; 4) accommodate the contractor’s requests for information; 5) make design changes based on field observations; and 6) incrementally assess rock block stability. The 3D model was created using BIM software and automated using custom programming to link per-plan, proposed, and as-installed tiebacks between the 3D model, field logs, and a stability analysis. This system allowed for a near real-time 3D model and stability analysis, which were easily communicated between the design team and field staff. This workflow and automated model nearly eliminated manual editing of the 3D model, accelerated contract document response time, and helped reduce risk for the owner, contractor, and engineer. Here, we present a successful case study utilizing the Observation Method and a real-time 3D model to complete a project with numerous complexities relating to design, communication, and risk.

By Alan J. Lutenegger

A series of tension tests were performed on prototype scale steel pipe piles at two sites to evaluate the influence of scale and pile plugging on the unit skin friction developed in axial tension. The first site consisted of a clean medium dense fine sand above the water table. The second site consisted of a loose silty sand with the water table within about 0.5 m of the ground surface. Pile load tests performed at each of the sites included piles with diameters ranging from 73 mm to 114.3 mm, which may be considered driven "micropiles". At the first site, pile lengths of 6.1 m were used; at the second site, pile lengths of 9.1 m were used. Some of the piles were driven open-ended while others were fitted with a conical tip to form a closed end. During installation, pile plugging measurements were taken on the open-ended piles after each 0.30 m of penetration. The piles were allowed to rest for a period of about 30 days after driving prior to performing the axial uplift load tests to failure. The results indicate that in the medium dense fine sand the unit skin friction developed in tension is dependent on both the amount of plugging that occurs and on the size of the pile, which was not the case for the loose silty sand.

Jan 1, 2000

By Renato P. Cunha

The paper presents the results of a comparative and parametric analysis in which a numerical program developed exclusively for groups of deep foundations under general loading (vertical, horizontal and moment loads) was used. This program, developed in the doctoral thesis work of Zhang (2000), extends the finite layer method to accommodate a simultaneous general loading on top of piled raft foundations, allowing the establishment of a coupled relationship between displacements (in all three directions), rotations (in two directions), and external loads. Zhang (2000) has extensively tested and validated this program against well known case histories, but has not applied it to piled rafts overlying unsaturated tropical soil materials. Hence, this paper further explores the applicability of this program by using it to simulate the behavior of experimental field loading tests carried out at the University of Brasilia (UnB) experimental site. At this site, Cunha and Sales (1998) and Sales (2000) carried out several loading tests on small scale isolated rafts (1 x 1m) and piles (L=5m, dia=0.15m), group of piles (4 piles, raft clear off the ground) and piled rafts (1 and 4 piles underneath a raft in contact with the soil). The authors adopt Zhang's program to backcalculate, hence simulate, this series of experimental field loading tests under vertical loading. They also use this set of results to "calibrate" the program for further parametric analyses. The parametric analyses were carried out with different piled raft configurations in this same soil type, trying to evaluate their field behavior under the effect of distinct (geometric) configurations of pile distribution.

Jan 1, 2002