Search Documents

By P. Leo

The Al-Zn-Mg alloys (e.g. 7004, 7020) are employed for land transport and architectural applications whereas the Al-Zn-Mg-Cu alloys (e.g. 7075, 7050) provide the high strength aircraft alloys. The Cu gives rise to suitably sized and distributed precipitation but causes high quench sensitivity. Their hot work processing also has marked differences; the Cu-free alloys have good extrudability whereas the Cu-bearing alloys have low extrudability and are difficult in rolling as well. The behaviors of the two classes are described in terms of flow stresses and ductility over 300 - 500°C, along with constitutive contrasts. The ductility of the alloys with Cu is much reduced above 400°C by precipitation of a phase at the grain boundaries that can be avoided by suitable heating schedules. The high strength alloys are subject to de-lamination corrosion of sheared edges due to severely pancaked grains; this can be alleviated by holding between passes, in mid-rolling schedule. In torsion tests at 10-1 to 10 s-1/ 250 - 500°C, the stresses (ductilities) at 300°C/ 1s-1 and activation energy Q for 7004 were 118 MPa (2) and 262 kJ/mol. The 7075 was tested after several pretreatments: completely over-aged (softened): 107 MPa (5), Q=150 kJ/mol; whereas, solution and quick cooling to testing caused extraordinarily high peaks related to dynamic precipitation resulting in 160 MPa (1.2), Q=300 kJ/mol.

Jan 1, 2011

By Mostafa Benzaazoua, Bruno Bussière, Philippe Poirier, Denis Bois

"Environmental desulphurisation is an attractive alternative for the management of acid generating tailings. Non selective froth flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works (McLaughlin and Stuparyk, 1994; Bussière et al., 1995; 1998; Benzaazoua et al., 2000a,b; 2002). This process can reduce the volume of problematic tailings to manage, by making a sulphide fraction concentrate. The desulphurized tailings can then be used as a moisture retention layer in a cover with capillary barrier effects to prevent acid mine drainage.In this paper, the authors present the results from different laboratory and pilot scale flotation tests which confirm that low sulphide, non-acid generating tailings can be produced by froth flotation. It is also demonstrated that the sulphide concentrates obtained from desulphurisation, when mixed with binders gave good long term results in terms of mechanical behaviour, thus demonstrating that the sulphide fraction can be used for paste backfill material. From previous work (Bussière et al. 1998, 1999) on the evaluation of the operating and capital costs of the desulphurisation process for different ore types, the use of desulphurized tailings to create a dry cover was then studied for several scenarios. The desulphurisation process was compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation and the advantages and disadvantages of desulphurisation are presented as well as the costs of this method of AD prevention.INTRODUCTIONThe principal environmental problem of the mining industry today is the generation of acidic drainage (AD) resulting from the natural oxidation of the sulphides in mine tailings. This phenomenon involves the generation of acidity which increase the amounts of toxic metals in the waste water released into the environment by a mine. The environmental impact of the AD has been described in detail in previous work (e.g. Down et Stocks, 1977; Ritcey, 1989; Gray, 1997; Ripley et al., 1996; Aubertin et al., 2002)."

Jan 1, 2004

By Polysius AG

"The Lone Tree demonstration was an important milestone in bringing High Pressure Grinding Roll (HPGR) technology into hard rock applications in the mining industry. HPGRs have become standard equipment in the cement, iron ore, and diamond industries over the past fifteen years, but their use in severe duties found in the hard rock mining sector has been restricted due to high roll wear and subsequent low availability. HPGR availability has historically been limited because of frequent downtime for edge weld rebuilding as the rolls wore and short tyre life from high roll surface wear rates.Recent advancements in HPGR wear protection are now being evaluated for commercial applications in the gold and copper mining industry where this technology may offer benefits in comminuting hard and/or abrasive ores and in improving metal recovery in heap leaching applications.Proving the feasibility of HPGRs for processing competent, abrasive gold ore, Newmont Mining Corporation, the world's largest gold producer, operated an HPGR demonstration plant employing a POLYSIUS (POLYCOM) HPGR incorporating some unique wear protection, at their Lone Tree gold mine near Winnemucca, Nevada. Results of the successful demonstration are presented and evaluated in this paper.The Lone Tree HPGR demonstration plant operated for three months, from April through June 2003. The HPGR operated for 1626 hours and processed 141,000 tons of ore. This technology demonstration focused on measuring operating performance, wear characteristics, and availability of today's HPGR technology.Polysius' innovative roll surface wear protection system eliminated edge-welding downtime. Improved surface wear protection extended tyre life to predicted durations acceptable for very abrasive service. The POLYCOM HPGR is now deemed suitable for selected hard rock applications."

Jan 1, 2005

"Drilling twinned holes is a traditional technique used for verification of intersections of high-grade mineralization, testing of historic data, or confirmation of drillhole data during geological due diligence studies. Twinned holes can also be used for special tasks such as correcting earlier data that are recognized to be biased. Successful implementation of the twinned-holes technique requires thorough planning. Experience suggests that good practice is to drill twinned holes no more than 5 m apart. Many unsuccessful twinned-holes programs could possibly have failed because the twinned holes have been drilled too far apart.Twinned holes are best compared by mineralization intersections and, if the data and geological characteristics of the deposit permit, by samples, equal-length composites, or geological units. Variables to be verified by twinned holes should include the thicknesses of the geological units of interest (e.g., mineralized thickness) as well as the presence of significant geological features (e.g., ore/mineralization contacts, alteration, etc.).A formal, rigorous analysis of twinned-hole data is essential. Repeatability of sampling, analytical results, and bias must be analyzed and statistically quantified. The number of twinned holes required for conclusive statistical and geostatistical analysis can be as high as 20-30, in particular where the studied variables are characterized by high short-range (local) variability.The efficiency of this approach is demonstrated by several examples of successfully applied twinned-hole projects, including applications to orogenic gold, mineral sands, bauxite, and iron ore deposits."

Jan 1, 2009

By S. R. Amos, N. O. Lotter, A. L. Hannaford, J. F. Oliveira, D. W. Broughton

"Ivanplats Ltd appointed Xstrata Process Support to perform the flowsheeting development work for their hypogene and supergene geomet units of the Kamoa Copper deposit, located in the Democratic Republic of the Congo. Through systematic flowsheet development using modern Process Mineralogy, the optimised milestone flowsheet delivered a saleable concentrate grade of 32.8% Cu at 85.4% recovery with hypogene ore, and a saleable concentrate grade of 45.1% Cu at a recovery of 83.4% for supergene ore. The significant value of this development is that a single flowsheet will treat both hypogene and supergene ores and produce saleable concentrates. Further work to advance the flowsheet performance has been identified for investigation in the near future.INTRODUCTIONLocation and Description of the Kamoa DepositThe Kamoa copper resource is located some 40 km west of the city of Kolwezi, in the south west of the Katanga Province of the Democratic Republic of the Congo, in the region of Central Africa. Drilling at Kamoa in 2008-2009 had discovered laterally continuous, sediment-hosted, high-grade stratiform copper mineralisation in a newly discovered copper district that forms a previously unrecognised western extension of the famous Central African Copperbelt – which hosts such world-class deposits as Kolwezi, Tenke-Fungurume, Konkola and Nchanga. This discovery showed that the western end of the Copperbelt in the Congo does not terminate at Kolwezi (Friedland & Broughton, 2009). The resource contains hypogene and supergene geomet units with a transitional zone located inbetween the (upper) supergene and the (lower) hypogene. In the hypogene unit, the major copper sulphides are bornite, chalcopyrite and chalcocite, whilst in the supergene, the sequence is led by chalcocite, then bornite, and finally chalcopyrite. Covellite is present in both units as a minor copper sulphide. Both geomet units will be mined and treated in one concentrator, either as blends or as campaigns."

Jan 1, 2013

By Ernest Baafi

A simulation model RoadSIM using the ARENA modelling system has been developed to evaluate roadway development options for a given development panel configuration. The RoadSIM simulation system has provisions for variability/randomness in operations including cutting and loading at the face, tramming and discharge of coal to the boot end and availability of equipment. The modelling system provides a means for assessing the operational limitations of roadway development practices at a particular coalmine. It is a ?what if? tool that allows a range of equipment, configurations and operating practices to be assessed in terms of achievable advance rates and equipment utilisation. Output from the system is in the form of a dynamic visualisation as well as summary reports and detailed logs of operations over time.

Oct 1, 2009

By B. K. Gorain

"Mining of low grade deposits along with the necessity to design and operate flotation plants with high throughput presents unique metallurgical and environmental challenges that need to be addressed to reduce project risks, improve project economics and to sustain the profitability of operations over the life of a mine.Some of the key challenges include poor recovery of valuables and concentrate quality issues due to complex mineralogy, the need to use poor quality water such as brackish or sea water, reduce environmental impact from the process, integrate flotation with hydrometallurgy to maximize precious metals recovery, escalation of capital and operating costs, use of unproven technology and constant use of larger equipment, high ore variability, worldwide constraints on resource availability and an ever increasing need for reliable metallurgical input to financial models to evaluate economic viability of projects.The need to develop effective solutions to these problems in a short time frame is becoming a key to the success of any new project and for sustaining the profitability of a mining operation. An integrated multi-disciplinary approach to problem solving is crucial with the need for a more lateral thinking along with strategic partnerships and collaboration involving the right players. This paper presents some of the key findings based on experiences from a large number of challenging projects and operations focused on solving complex flotation problems.INTRODUCTIONThere are various challenges to successful development of mineral resources. Most of the ore bodies being developed worldwide are of lower grades requiring high throughput to be economical. Many of these lower grade ore bodies have significant occurrences of deleterious and penalty elements that could render a deposit unworthy of development unless there are technological solutions to process them economically in a sustainable manner with minimal environment impact. Even in a high metal price scenario, the economics for some of these low grade ore deposits is marginal. From a metallurgical perspective, these ore bodies have complex mineralogy and use of any off-the-shelf technology is not always effective. Development of innovative processes are often required, which is expensive, time consuming and sometimes risky.This paper will provide a broader perspective on the steps involved in solving flotation problems for operating plants and for greenfield development projects. In addition, some of the key challenges in flotation of complex low grade ore bodies along with the economic benefits in developing solutions to these problems will be presented."

Jan 1, 2013

By Chris Larsen, Ian Orford, Marilene Renaud, Mike Cooper, Lud Strah

"An AG/SAG mill was commissioned at the Brunswick Mine concentrator in October 1998. This paper discusses the original liner design for the bi-directional AG/SAG mill, observed liner wear, subsequent liner design modifications, and benefits. The mill liners consist of steel top hat shell liners, steel end liners, rubber grates and rubber lined pulp lifters.Lifter profile and plate thickness measurements were made on monthly shop days. Trends of wear rates were used to project when liners required replacement. Wear profile information was also used to determine where liner re-design would improve wear life or minimize scrap loss. Charge motion simulation modeling was used as a tool to assist liner design modifications.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large underground lead/zinc mine with a nominal production rate of 10,000 tonnes per day. The Brunswick concentrator commenced operation in 1964 with conventional surface crushing followed by rod and ball milling to reduce run of mine ore to the required size to feed two parallel flotation circuits. In 1998 the AG (autogenous grinding) mill was commissioned for a nominal production rate of 9,000 tonnes per day replacing two surface crushing plants, three rod mills and three primary ball mills. In May of 1999 the mining rate was increased and the service of the AG mill was changed to a SAG (semi-autogenous grinding) mill with the addition of 4 inch steel balls (4% volume). The mill operates in closed circuit with 0.66 meter horizontal cyclones to produce a ground product of 90 micron nominal size (K80).The AG/SAG mill liners are steel (Norsteel, chrome-moly steel) with rubber grates and rubber lined pulp lifters.The original liner design was based on studying other AG/SAG mills and recommendations by the liner supplier, Norcast. Design factors taken into account were total cost of lining (including material and labour), protection of mill shell and impact on operating performance."

Jan 1, 2003

By Pierre Roy, Claude Gosselin, Maryam Sadeghi, Michel Bourassa, Christian Rochefort, Claude Bazin, Gautier Mahieu, François Lavoie, Marilène Renaud, David Cataford

"Spirals are gravity concentrators used for the concentration of iron oxide minerals from ores. This paper presents the mineral size recovery curves observed for spirals operating in two Canadian iron ore processing plants. The size recovery curves are presented for rougher, cleaner and re-cleaner spirals. The partition curves observed for the spirals are significantly different than those observed for typical gravity concentration devices such as hydrocyclones or hydraulic classifiers. The size recovery curves show the complex behaviour of the minerals as they flow down a spiral and are analysed with a view toward process modelling and simulation. Initial simulation results show that gains in the iron recovery can be achieved by increasing the recovery of coarse iron oxide particles in the rougher spirals.INTRODUCTION Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and different heavy minerals ores (Wills, 1992). The classification of the particles in spirals is based on the combination of gravity, centrifuge, drag, lift and Bagnold forces (Atasoy and Spottiswood, 1995; Burt, 1984; Bouchard, 2001). Several papers are dedicated to the analysis of the forces acting on the particles flowing down a spiral (Das and al., 2007; Sivamohan and Forssberg, 1985; Holland-Batt and Holtham, 1991; Holtham , 1992). Most of these papers aim at the development of a general model for the simulation of the classification of the particles for coal ore processing. Few papers deal with the operation of spirals for processing iron ores (Hyma and Meech, 1989; Srivastava, 2001; Dallaire et al., 1978) and fewer papers present results for spirals used as cleaners following a rougher stage. Since the classification in spiral classifiers is dependent on the particle size and specific gravity a partition or performance curve commonly applied to classifiers (Mai Manga et al., 2012) is used here to analyse spiral operation. Few papers were found to describe the operation of spirals in terms of partition curves (Atasoy and Spottiswood, 1995; Holland-Batt and Holtham, 1991; Richards et al., 2000). Most of the investigations presented the application of a model to simulate the position of coal particles of various sizes and specific gravities along the trough of a spiral (Kapur et al., 1996; Holland-Batt and Holtham, 1991). In addition most of the available literature on spirals deals with one stage of concentration by spirals (Dallaire et al., 1978; Das and al., 2007; Sivamohan and Forssberg, 1985) while industrial circuits usually consist of rougher and cleaner spirals."

Jan 1, 2014

By Janis A. Shandro

The mining sector is a major economic driver for Canadian, and British Columbian communities. In parallel strong commitments have been made by industry to the well-being and sustainability of associated communities. However, these dimensions are the least understood. Especially lacking are focused regional investigations that compare the well-being and sustainability of communities dependent on different resources sectors. It is hypothesized that this type of comparative analysis will help to foster a greater understanding of what makes a resource or mining community healthy and sustainable. This paper describes research that examined community-level indicators associated with well-being (e.g. education, income and employment) and sustainability (e.g. economic diversity). The indicators were derived from Canadian Census data for 31 British Columbia resource-based communities (with a focus on mining) during a period of time (1991 to 2001) when resource sectors experienced an economic downturn. Our findings identify that during this decade, mining communities differed significantly from other resource-based communities, and comparative analysis of census derived indictors illuminate challenges that mining communities in British Columbia face with respect to wellbeing and sustainability (such as economic diversity, unemployment, and population loss). To contribute to the mining sector?s efforts towards meeting their commitments to communities, this paper concludes by proposing strategic opportunities aimed at the enhancement of mining community sustainability for policy-makers, communities, and the mining industry to consider.

May 1, 2011

By Glenn Kosick, John Starkey, Glenn Dobby

"A practical new test has been developed for SAG hardness determination. Using two kilogram samples of minus one inch diamond drill core or crushed muck samples, the Starkey SAG Test has been shown to give accurate predictive information which directly relates to on-stream SAG mill performance. Typical results and test criteria are discussed in the paperAchievements to date include:• Identification of hardness profiles and the location of hard and soft zones in a large ore body.• Accurate prediction of the hardness of a bulk sample by using an adjacent diamond drill hole.• Derivation of a plotted curve relating pilot plant power to laboratory relative hardness.• Demonstration that for every test done to date, the Starkey SAG Test produced a product size distribution identical to that produced in a pilot plant or full scale plant SAG operation.This test can now be used for blast hardness monitoring and short term control of mine production in existing plants and for identifying the proper locations for bulk samples in new projects. In addition, new SAG mill design can now be rationalized in a low cost way to eliminate unforeseen production shortfalls.IntroductionThis paper is presented to introduce the Starkey SAG Test, a practical new laboratory tool for measuring the relative hardness of small ore samples in a semi-autogenous grinding (SAG) environment. The test was first designed for use on diamond drill core samples during the prefeasibility stage of new mining projects, to provide new information about the ore body at reasonable cost. It is a new tool and does not replace existing pilot plant test requirements.The test will also be useful for throughput prediction in existing SAG plants by assisting in short and long term mine planning, where forecasting of metal grades and milled tonnage is used to control mine profitability. Because in-plant hardness testing has previously been unavailable on small samples, this test offers exciting possibilities for SAG mill operations where hardness variation is or could be a problem.The Starkey SAG Test provides the following benefits to the mining industry"

Jan 1, 1994

By L. W. Vigrass

Porous and permeable rocks deeply buried in sedimentary basins contain immense volumes of hot water with the potential to supply low-grade heat energy. A part of Canada with sizeable potential for low-grade geothermal energy is the northern Williston Basin of southern Saskatchewan. In this region, the University of Regina has conducted a geological study investigating the feasibility of producing large quantities of warm water suitable for space heating in the Regina - Moose Jaw area. The study has shown that the most favourable geothermal reservoirs are in the Basal Clastic Unit (Cambrian Ordovician), which, at an approximate depth of 2,000 metres has predicted temperatures of 71°C to 74°C. We anticipate sustainable flow rates from these reservoirs of 100 to 300 ms/hr. The water contains about 150,000ppm of total dissolved solids, mostly sodium chloride. It is anticipated that the sulphate content will be 3,000 to 6,000 ppm, that the dissolved oxygen and hydrogen sulphide content will be small, and that the waters will be neutral to slightly alkaline. It is anticipated that the piezometric level will be 46 m below the ground surface for reservoirs in the upper part of the Basal Clastic Unit and 141m below the ground surface for the lower reservoirs of the unit. Plans are to build a low-grade geothermal research, testing and demonstration facility at the University of Regina. To be a practical demonstration, the facility will have to handle very large volumes of water. Because of high salinity, the water will be re injected into a subsurface reservoir. We do not anticipate insurmountable problems because of salinities or as a result of corrosion provided that the waters are not aerated during handling

Jan 1, 1979

By L. D. Smith

"This paper examines the impact of the various assumptions that go into an economic evaluation, and shows how these can be combined to show an exciting result that may not really exist. An example of an embellished case (the kind that one frequently sees when projects are being promoted) is developed and the cumulative impact is analyzed to show the actual project underneath. The paper also points out some areas to watch for overly optimistic assumptions such as prices, inflation, and debt. The concept of a “bare bones” base case is proposed (constant metal prices, constant dollars, no inflation, no debt, no interest, on a project basis, after tax) as a common reference point.As well, the discount rate is examined as one of the fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk."

Jan 1, 2002

By Claude MacDonald, John H. Ashburn

"IntroductionIndustrial growth and technological change over recent years had been accompanied by two major sources of concern to management and employees: (a) increase in occupational injury and illness and the resultant costs involved; and (b) equipment damage and breakdowns in concentrated production lines causing more extensive loss potential.Due to economic factors, management attention has focussed more on production and quality than on safety, health and related loss potential sources. As a result , occupational safety and health activism has grown, government legislation of compensation and occupational safety and health standards have progressively developed and stronger liability attitudes have been taken by courts of law.To improve efficiency and allow development in more competitive markets, rising labour costs, equipment costs and safety related financial losses have dictated that attention be given to conservation of all resources. Conservation of resources, people, equipment, material and environment, can no longer be addressed in isolation but must be managed integrally with production and quality. To this end, systems have developed utilizing sound management principles applied with equal intensity to production, quality and loss potential"

Jan 1, 1987

By R. Bruce Ferguson

"IntroductionThe Beaverlodge Operation of Eldorado Nuclear Limited is a uranium property located near the north shore of Lake Athabasca about 7 miles from Uranium City, Saskatchewan.The mill is a 2000 tpd carbonate leach operation producing a high grade yellowcake concentrate.The Lamella Thickener was purchased to replace a 55 foot conventional unit which had deteriorated beyond repair. The cost of the unit was considerably lower than for a conventional unit, installation was much simpler and the unit is much more compact allowing it to be installed in the mill basement and be insulated completely.The unit was sized according to the results of tests performed both by the supplier and Beaverlodge engineering staff. The supplier guaranteed overflow clarities of less than 100 ppm suspended solids. The Lamella thickener was developed by A. Johnson Co. of Stockholm, Sweden, is manufactured under license by Parkson Corporation of Ft. Lauderdale, Florida and is distributed in Canada by A. Johnson Co. of Montreal."

Jan 1, 1975

By G. Stokreef, B. R. Davis, M. Kadiyski, Alvear Montenegro, H-P. Loock, V. Montenegro

An optical probe for burner monitoring in copper flash smelting, first developed at the University of Concepcion, is being industrially tested in a collaboration between Kingston Process Metallurgy, Aurubis AG, and Queen’s University. The sensor uses fibre-optics and optical emission spectroscopy to analyze the light emitted from combusting particles in the furnace reaction shaft. Information that can be extracted from the emission spectrum includes the temperature and brightness of the flame, as well as emission lines or bands from excited atomic and/or molecular species. Laboratory proof of concept testing of the sensor was first completed in a continuously fed drop tube reactor using O2/S stoichiometric ratios between 0.8–4.0. These O2/S stoichiometries capture the industrial operating condition, which is typically less than 1. The results from lab testing justified a plant trial of the optical probe, which was done in the Aurubis Hamburg flash furnace in September 2018. From this trial, approximately 31 hours of spectral data were collected and synchronized with furnace operating data. The results from both drop tower test work and the plant trial are discussed with implications for process monitoring in the commercial furnace. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process. It is used to treat copper sulphide concentrates and small amounts of secondary materials, such as dust generated by the process. O2 enriched air and the concentrate blend are fed into the furnace reaction shaft through the concentrate burner. As the particles fall through the reaction shaft, they heat up and ignite, causing rapid, exothermic reactions that oxidize the iron sulphide, some copper sulphide and impurities in the feed. Reacted particles fall into the settler of the furnace, melt and separate into a matte and slag, while the SO2 enriched off-gas is carried out of the furnace for heat recovery and H2SO4 production. Operation of the furnace is achieved by adjusting a limited number of control variables. The main variables are the blast feed rate, blast oxygen enrichment, SiO2 flux feed rate and CH4 combustion rate (CH4 is used when the chemical energy of the concentrate is low) all measured relative to a set feed throughput. (Davenport & Partelpoeg, 1987; Davenport, King, Schlesinger & Biswas, 2002) The batch tapping nature of flash furnaces makes operation difficult because these control variables impact each other, and product quality can only be measured when matte and slag are tapped from the furnace. This means that operation of a furnace is based on feedback control from matte and slag assays. Because of the time-delay associated with understanding product quality, there is interest in using technology to monitor the combustion reactions that happen in the furnace reaction shaft.

Jan 1, 2019

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Oct 1, 2004

By Gabka T., R. E. Gregorczyk

Work to improve employees' behavior in Głogów Copper Smelter began in 2009. It has been noted that over 90% of accidents at work are attributable to human reasons. At that time, a series of external workshops was contracted based on exercises conducted by a psychologist trainer with supervisors. Having trained about 300 employees, an observation of employee behavior at workstations was started as part of the control of risk reduction measures. As a result of the above actions, the number of accidents was reduced by half between 2009 and 2017. Currently, internal workshops for communication improvement for behavioral auditors are conducted by the employees of the Smelter. Named: "I observe, react and communicate" and aimed at further mastering the elements of the safety culture in Głogów Copper Smelter. INTRODUCTION KGHM Polska Miedz is an integrated mining and smelting copper producer based in Poland and operates on the international metal market. KGHM, with annual production of over 500 thousand tonnes of copper, holds a middle position in the world ranking of copper producers. At the same time, in Europe it is the largest producer of copper from its own ore deposits, possessing its own integrated production structure, from underground mining operations to final, top-quality product. It is also worth mentioning that KGHM Polska Miedź is one of the largest Polish exporters and, apart from copper, is a significant primary silver producer in the world. The mission of our company, consistent with its strategy, is to produce copper and silver in a safe mode for workers and the environment, with reduced environmental impact. Therefore, "Głogów" Copper Smelter operations are continuously focused on the creation of safe working conditions, and minimizing the negative effects on the environment. The company meets the requirements of an Integrated Management System comprised of the following: Quality Management System ISO 9001:2008 Environment Management System ISO 14001:2004 OHS Management System according to the requirements of BS OHSAS 18001:2007 Being a proud socially responsible company, we are aware that part of an efficient OHS system is to recognize, monitor, prevent, educate and motivate, thus continuously improve working conditions for 2500 employees of Głogów Copper Smelter &Refinery. We clearly communicate that a low accident rate is beneficial for both, staff and the company, and is of utmost importance as a part of our health policy.

Jan 1, 2019

By J. Duncan Crone

"A test surface Pulse EM(PEM) survey over a plunging massive sulphide lens, located in the Snow Lake area of Manitoba, has shown that it is possible to detect the body to a depth of 300 metres. Another surface survey in the Athabasca basin of Saskatchewan, clearly outlined a large, basement graphitic zone below 450 metres of sandstone cover. Deep detection of these conductive bodies was achieved by energizing large volumes of ground with a strong transmitted EM field. Such large fields also energize all other conductors present in the exploration area. Both of the above survey results indicate that more than one conductor is present. In such cases, detailed field coverage is required for accurate interpretation, and interpretational procedures that assume simple geometrical shapes should be applied with caution. In all cases geological and geophysical information should be coordinated in detail. The first test drill hole still has a high risk of missing the deep conductive body and two or three holes should be budgeted per target.Borehole Pulse EM surveys are now routinely used to help zero in on deep conductive targets. They are also proving effective in development drilling programs by outlining the edges of conductive bodies. The results of surveys from northern Quebec illustrate how they may provide more accurate shape and tonnage estimates."

Jan 1, 1985

By Paul Armstrong

THE first discovery of lead and zinc ore on Calumet island was made in 1893 by John Lawn, who then staked a portion of the property now owned by Calumet Mines, Limited. His discovery was developed by James and Calvin Russell, who are said to have shipped a few tons of sorted ore, averaging 39 per cent zinc, 13 per cent lead, and 11 oz. silver per ton. In 1898, the property was being operated by the Grand Calumet Mining Company, who mined and shipped, for treatment in a Belgian smelter, 1,100 tons of ore averaging 32 per cent zinc, 9 per cent lead, and an unreported content of gold and silver. After some indecisive exploration by an American syndicate in 1907, the property lay idle until1910, when the Calumet Metals Company-later reorganized as the Calumet Zinc and Lead Company-re-commenced exploration. After sinking an 85-foot shaft-the McDonald shaft-and doing a few hundred feet of drifting and cross-cutting, this Company, in 1912, erected a 150-ton daily capacity gravity-concentration plant, in which some 800 tons of ore, mined from the McDonald shaft and Bowie pit, were milled. Owing to very disappointing mill recoveries, the property was shut clown and-after several years of idleness-in? 1916 the mill and mining plant were destroyed by fire and the Company went into bankruptcy. In 1918, an unknown operator shipped to an Omaha, Nebraska, smelter 22 tons of ore, probably sorted from the dumps of the Ste. Anne shaft and Galena pits, averaging 44 percent lead, and 0.26 oz. gold and 61 oz. silver per ton. The British Metals Corporation (Canada), Limited, in 1926, optioned the property. They unwatered the McDonald shaft and, after doing an additional 300 feet of cross-cutting and drifting on the 85-ft. level, estimated there were some 33,000 tons of ore between this level and the surface. Surface exploration, including trenching, on other showings on the property gave discouraging results and the option was dropped.

Jan 1, 1941