Search Documents

By C. Caners

One of the main uses of fossil fuels is in the transportation sector, leading to environmental consequences such as climate change. In order to move towards a more sustainable energy infrastructure, a transition must begin from fossil fuels to renewable fuels, derived from e.g. biomass. One means of facilitating this transition is to develop reforming technology that can extract hydrogen from a suitable fuel that is either fossil fuel or renewable in origin. The hydrogen would be feed to a 'fuel cell' engine that would power the car, truck or bus. One reforming technology that is attractive for automotive applications is autothermal reforming (ATR). Autothermal reforming is the combination of steam reforming and partial oxidation, whereby a portion of the fuel is combusted using a sub-stoichiometric amount of air, and the resulting thermal energy drives the more desirable steam reforming reaction. ATR is attractive for fast start-up, rapid load following and ease of control. ATR also has the benefit of smaller volume and fewer peripheral requirements as compared to other reforming technologies. Recently, a bench-scale gasoline autothermal reformer (ATR) was constructed and tested. This ATR employs a novel design, consisting of three concentric annuli in order to promote heat transfer from the partial oxidation reaction to the steam reforming reaction. Concurrently, a CFD based model (FLUENT) of the ATR that considers the geometric complexity of the reformer was validated. In spite of the use of simplified kinetics, the model predicted well the observed trends in temperature and overall performance. This paper will discuss the use of the model to improve the design of the ATR. The impact of various system parameters upon performance will be investigated along with alterations in the geometry of the ATR. The various tradeoffs in performance and system volume/size will be highlighted in the context of a fuel cell power system.

Jan 1, 2005

By D. MacGREGOR, VERA TUREK

The St. Canul and Ste. Scholastique orthoquartzite sanrjstone deposits are located within the Potsdam Formation near Montreal. The sandstone lies on Precambrian basement and is Cam/3rian to Ordovician in age. The Potsdam Formation shows two distinct stages of development. One created a deepwater facies represented by impure, limey or shaley sandstone; the other produced a shallow facies composed of grey, highpurity sandstone. The shallow-water orthoquartzitic sandstone at St. Canul is being mined and beneficiated by lndusmin Limited. The operation manufactures a wide range of silica products and supplies industrial areas of Quebec and Ontario with material for the glass, foundry, silicon carbide and ceramic industries.

Jan 1, 1984

Cameco Corporation is in the process of revitalizing the Key Lake mill. As part of this process, the company is considering installing the Rabbit Lake style strong acid stripping in solvent extraction. This would lead to using hydrogen peroxide for uranium precipitation. The process currently employs ammonia stripping and ammonia precipitation. As part of the process evaluation, an indirect fired drier pilot plant test was conducted. This paper will discuss the results of that test work, including the relationships between the following: ? Drying temperature and product grade ? Drying temperature and product colour ? Drying temperature and product reactivity with water ? Drying temperature and energy input requirements ? Drying temperature and shipping costs

Aug 1, 2010

By Z. S. Abisheva

The Zhezkazgan copper sulfide ore deposit in Kazakhstan contains both rhenium and the rare osmium isotope "osmium-187" (187Os) in the high isotopic purity of 99.4 ± 0.2%. This isotope is believed to have originated as a result of the disintegration of one of the rhenium isotopes, according to the reaction: 187Re75 ?> 1870576 + B- + v~ (where B is a 13-particle, v~ is a 3-disintegration antineutrino). The distribution of osmium and rhenium in metallurgical byproducts produced during the recovery of copper from these ores has been studied and process flowsheets for the processing of rhenium and osmium-containing byproducts have been developed.

Jan 1, 2007

By Peter McBride

Human excellence in all areas of endeavour is acknowledged and recognized. Establishing role models and spreading the word on best practices helps broader audiences. For on-the-job safety, recognition awards are a component of successful programs. In Canada?s mining industry since 1941, the John T. Ryan Safety Trophies initiative has contributed to the sector?s improving record in this area. The much sought after and rich in history John T. Ryan trophies are recognized symbols of safety excellence in Canada. The effectiveness of the Ryan safety recognition program in Canada has led to its export to other mining countries seeking to improve their overall safety performance.

May 1, 2008

By M. Cimenti

Fuel cells have tremendous potential as power sources but much fundamental research is still required. One key component of the research is the experimental set-up used. In particular, the placement of the reference electrode is extremely significant in measuring the half-cell overpotential of solid oxide fuel cells, since differences in area, misalignments, and also differences in the kinetics of the working and counter electrodes can cause both scaling errors and frequency distortions of the measured impedance. The impedance of thin solid electrolyte cells of different electrode geometries has been calculated using the finite element method and the results compared to experimental values obtained for the oxygen reduction reaction on platinum.

Jan 1, 2005

By J. H. Baek, D. W. Lee, B. K. Kim

Nanostructured Cu-Al203 composite powders were synthesized by thermochemical process for an electrode application. The synthesis procedures are 1) preparation of precursor powder by spray drying of solution made from copper and aluminum nitrates, 2) heat treatments to evaporate volatile components in the precursor powder and synthesis of nanostructured CuO+Al2O3, and 3) CuO reduction by hydrogen into Cu. The suggested procedures stimulated the formation of the gamma-Al2O3. The mean particle size of the final composite powders was 20nm, and the electrical conductivity and hardness in the hot-extruded bulk were competitive with Cu/Al2O3 composite by the conventional internal oxidation process.

Jan 1, 2004

By A. Cadieux, J. -B. Pineault, C. Allaire

The temperature measurement of the molten metal in the aluminum transformation process is of prime importance. This is particularly the case for aluminum treatment furnaces, such as holding and melting furnaces. Such reverberatory type of furnaces involve a thermal gradient across the metal line which limits the life of conventional thermocouple protective ceramic shields, due to the action of locally induced thermal stresses. This paper presents a novel thermocouple assembly using a composite refractory protective shield allowing long term resistance to such above conditions. Example of results obtained from various tests in aluminum holding furnaces are presented. The results confirm the superiority of the novel thermocouple assembly, as compared to conventional thermocouple units.

Jan 1, 2004

By J. H. Baek, S. Alexandrovskii, D. W. Lee, B. K. Kim

Nano-phase titanium carbide was synthesized by Mg-thermal reduction process using a novel route of Mg-thermal reduction. The processes are based on I) feeding of TiC14+CxC14 x = 1, 2 ) solution into liquid magnesium, 2) Mg-reduction of metal chlorides, 3) TiC formation by the reaction of released Ti and C atoms, and 4) vacuum separation of residual liquid phases of Mg and MgCl2. In this study, the process for titanium carbide production with composition close to stoichiometry and the minimum content of impurities was optimized with the various process parameters such as concentration of initial solution, its feeding rate and reaction temperature, as well as a kinetic study.

Jan 1, 2004

By G. Brooks, M. Hamed, S. Nightingale, K. Coley

The Marangoni effect plays a significant role in slag line corrosion of refractories. Previous experimental studies for various refractory /slag systems and mathematical models are reviewed and show that Marangoni flow is important in slag line corrosion under static conditions. Recent work by the authors is presented which also shows significant slag-line corrosion of MgO refractory in SiO2-CaO-FeOx-MgO slag. The rate of attack of the MgO was marginally slower in the case of slags containing alumina. A semi-empirical model developed by Hrma based on mass transfer control described reasonably well the observed progression of corrosion with time. Further work is proposed to evaluate this model.

Jan 1, 2004

By T. Melfi, M. James

Attaining required mechanical properties in welds made using the double submerged arc welding (DSAW) process is difficult, and it is becoming more difficult as the strength level of the base materials continues to increase. Producing weld metal with adequate mechanical properties involves factors that are often overlooked and not taken into consideration. Not least amongst these problems is simply finding information to use in selecting the appropriate flux/wire combination. Most of the available data on flux/wire combinations provided by consumables manufacturers is generated using the multiple pass welding procedures required for classification per specifications such as AWS A5.17 and A5.23. This data really gives no insight into the properties that can be expected in a DSAW application. Also, base plate composition plays a very significant role because of the fact that base plate dilution can be as high as 70% in DSAW welds. This means that if any elements are present in the base metal that are deleterious to mechanical properties, they will also be present in significant quantities in the weld deposit. Some of these elements can decrease toughness and increase hardness (increased hardness is a concern if the pipe is intended for sour service). Some of these problems can be mitigated by proper selection of welding consumables. Selection of proper welding consumables means selecting an electrode that provides the appropriate alloying elements to obtain the desired level of impact toughness while also keeping the hardness within any specified limits. In order to attain the necessary impact toughness, selection of a flux with an appropriate composition (in terms of its basicity and its ability to control the nitrogen content of the weld deposit) is required. As with all welding processes, the mechanical properties of DSAW welds are also highly dependent on the welding procedures. This work clarifies how to select appropriate consumables to meet a given set of requirements, and also how to achieve the optimum mechanical properties from those consumables.

Jan 1, 2005

By Lei Pan, Roe-Hoan Yoon

"Sea water flotation is becoming a reality due to shortages of fresh water. To better understand the mechanisms involved in sea water flotation, we have studied the effects of KCl and MgCl2 on the surface forces present in the wetting films of water formed on hydrophobic surfaces. The measurements have been conducted using the force apparatus for deformable surface (FADS), which is capable of measuring both the surface and hydrodynamic forces responsible for bubble-particle interactions. The results obtained with the gold surfaces hydrophobized with butanethiol (C4SH) show that the wetting films of Ultrapure water do not rupture despite the relatively high water contact angle (??= 80o) and the presence of a long-range hydrophobic force with a decay length (D) of 25 nm in the film. The film is metastable with its equilibrium thickness (he) at 140 nm, where the repulsive double-layer force is equal in magnitude to the capillary force as shown in Figure 1. The film loses its metastability and ruptures in a 10-2 M KCl solution, in which the double-layer force decreases substantially due to the decrease in Debye length (?-1) while the decay length of the hydrophobic force remains as large as 23 nm.The effects of MgCl2 has also been studied using a C4SH-coated gold surface with a water contact angle of 87o. It has been found that in a 10-4 M solution double-layer force decreases due to the decrease in the negative ?-potentials and Debye length, which should help destabilize the wetting film. However, the film remains stable due to the decrease in the decay length of the long-range hydrophobic force from 45 nm in Ultrapure water to 14 nm in the MgCl2 solution. Thus, the results obtained in the present investigation support the view that the difficulties in sea water flotation may be due to the presence of MgCl2 rather than the presence of NaCl in sea water (Ramos, et al., 2013)."

Jan 1, 2016

By D. Monder

Fuel cells are promising sources of electrical energy because of their exceptionally high efficiencies and low environmental emissions. Solid oxide fuel cells (SOFC) are high temperature, ceramic electrolyte cells, which unlike most other fuel cells, can work with a variety of fuels besides pure hydrogen, including hydrocarbons and hydrogen sulfide. In this presentation I present the models we have built for a single H2S fuelled SOFC. The goal is to model the electrochemical reaction coupled with mass transfer, fluid flow and current/voltage distribution in an yttria stabilized zirconia electrolyte fuel cell assembly operated between 750 and 850 °C. Two models of the above SOFC are discussed in this work, 1) an algebraic model derived by integrating a one-dimensional model along the thickness of the cell, and 2) a two-dimensional finite element axi-symmetric model. Important physical and kinetic parameters in the 1-D model are fitted using experimental data sets at three different temperatures and reasonable fits are obtained for the data sets at 800 °C and 850 °C. However, the third data set at 750 °C does not give a good fit using this model. We need to apply the curve-fitting to more data sets to investigate it further. The main conclusion that can be drawn from the present study is that the ohmic resistance of the cell is very high. Contact resistances are believed to be the reason behind this although there could be contributions from resistive interphases. The 2-D model also gives reasonable fits to data sets. One of the publications by the laboratory group doing the experimental work in our department presented very interesting data that shows the cell performance being a strong function of fuel flow-rate. We want to model this behaviour and will have to depend on the 2-D model as the 1-D model does not have flow-rates as parameters.

Jan 1, 2005

By Richard C. Williams, Herman Pieterse, Ken Thomas, K. S. Fraser, Ron H. Colquhoun

"The Banick Goldstrike Mines Inc. (Goldstrike) operation is located in Eureka County in north-central Nevada on the Carlin geological trend. Gold in the sulphide mill feed, occurs primarily as submicroscopic inclusions or possibly solid solution in a pyrite and marcasite matrix. Sulphide mill feed is pretreated in a pressure oxidation plant allowing gold recoveries of 90 per cent and greater to be achieved. Anticipated 1994 gold production for the sulphide gold facility is approximately 1,500,000 ounces.In January 1989 American Banick Resources Corporation (Banick) announced the US$365 million Betze Development Plan for the Goldstrike property. The Betze plan was based on a three (3) staged expansion of the original 4,500 STPD oxide gold plant. This expansion would involve addition of ore and gold processing capacity and the total conversion of all ore handling facilities to treating Betze sulphide ores.Phase 1 of the Betze Development Plan involved the construction of a pressure oxidation circuit, including a single autoclave and supporting ancillary services. The pressure oxidation circuit was commissioned in February 1990. Currently a throughput of 2,000 STPD is being achieved.Phase II of the Betze Development Plan, commissioned throughout April and May 1992, included the expansion of grinding, leaching, and gold recovery facilities enabling the treatment of combined oxide, and sulphide ore. Pressure oxidation capacity was increased by the addition of two (2) autoclave circuits each treating 2,600 STPD of sulphide ore and other required ancillary services. By June 1992, the Phase II gold facility had achieved a combined throughput of 15,000 STPD of oxide and sulphide ore.Phase Ill, the final stage of the Betze Development Plan, was successfully commissioned in February and March 1993. This final stage of development increased the design throughput of the pressure oxidation plant to 15,000 STPD by the addition of three (3) autoclave circuits with combined capacity of 7,800 STPD."

Jan 1, 1994

By Y. Kocaefe, S. Afshar, D. Kocaefe, Z. Kunt, C. Allaire

Interaction of aluminum with silica based ceramics Jose M. Soto, Jeffrey D. Smith, William G. Fahrenholtz. Department of Ceramic Engineering University of Missouri-Rolla Rolla, MO 65409-0330 USA ABSTRACT Interactions between A356 aluminum (Al-Si alloy) and dense fused silica (FS) riser tubes used for low-pressure casting of aluminum alloys were evaluated using a sessile drop approach. The tubes have a short service life, but cost and thermal shock resistance make them an effective solution. The main problem encountered during use is the reaction of aluminum with silica to form alumina and silicon, which causes failure. Tests have been conducted on as-fired (uncoated) and modified (coated) tubes. Experiments were carried out in a horizontal furnace at 1225°C under argon to minimize the effect of the aluminum oxide on the interactions at the alloy-silica interface. Images of the drop were acquired and contact angle values were estimated for uncoated and coated samples, but no significant differences in the contact angles were observed. Scanning electron microscopy revealed the presence of cracks at the interface between the reaction zone and the unreacted silica. The presence of reaction products (silicon in the reacting alloy and aluminum in a reaction zone between the alloy and the unaffected silica) has been confirmed using energy dispersive spectroscopy. A two layer coating system was found to be effective in reducing penetration of the aluminum alloy. The interactions between bed media and aluminum have been studied under static and dynamic flow conditions. An experimental system was set up simulating a small filter. Desired flow field can be created around alumina particles and velocities can be adjusted. A mathematical model was developed to predict the velocities, and this was validated using data from a visualization study. The interaction zone on the surface of the particles was analyzed with optical microscopy and SEM. This paper presents the study and compares the results under static and dynamic flow conditions.

Jan 1, 2004

By V. Pouyafar

Semi-Solid metal alloys, as used in SSM processing, have a special microstructure of globular solid particles suspended in a liquid matrix, which makes them behave differently in forming processes. The sensitivity of semi-solid slurries to temperature variations and their history and rate dependant behavior, make process design and control difficult. Precise selection of the process parameters is necessary in part production. Therefore, a numerical analysis and simulation of the process can be a valuable tool in process design. In this work we proposed a structural dependent model to account for the thixotropic behavior of semi-solid metals. The parameters of the model were then determined using rheometery tests. The results show a good agreement between the model and the experiments.

Oct 1, 2011

By M. Hosseinzadeh

By changing the quality of consumed refractory bricks in burner zone of sarcheshmeh copper complex anod kiln removing of carbon precipitation phenomenon was studied. For blister deoxygenation LPG is blowing in anod kiln and cause destoring microsturcture and bonding of refractory bricks. Studies are shown that in a part of the bricks which have a temperature of 800 - 1000 °C , iron content phases in magesia - chromite bricks are like catalist and cause increasing the rate of carbon precipitation reactions . In a way that in comparsion of two bricks with best and medium quality with different analysis, this problem is more critical in best quality bricks containing high iron oxide. Therefore special magesia spinel bricks suggested and installed in burning zone.

Jan 1, 2004

By M. R. Coffin

In recent years, improved operation of the Kidd smelter has resulted in an increase in blister production capacity. Due to manpower and equipment limitations anode production and treatment rates could not be increased without incurring significant additional operating expenses. The option chosen to expand casting and refinery capacity to meet the available blister supply was to increase the anode thickness while maintaining the same anode exchange cycle in the refinery. This has resulted in a cathode production increase of almost 10% for minimal expenditure. Equipment and process modifications required to cast and refine the thicker anodes are discussed in this paper, along with the Six Sigma methodologies used to identify them. Key areas covered are Hazelett continuous caster operation, refining process parameters, plating performance and cathode quality.

Jan 1, 2007

By M. J. Hadianfard

The effect of holding at temperature on fatigue life of a 10 vol% particulate SiC reinforced Titanium alloy has been investigated. The influence of holding time at 600°C on fatigue of this material has been studied by using tension-compression tests, scanning electron microscope and image analysis. The specimens were heated to 600°C by using a controlled atmosphere furnace; hold at this temperature for time ranging from 0 to 100 hours, and then fatigue tested at room temperature under controlled constant plastic strain. The number of cycle to failure found to decrease with increasing of the holding time. In addition the fracture mechanism and number of debonded particles has been significantly influenced by holding time at 600°C.

Jan 1, 2004

By E. Paransky, M. Rigaud, G. Paschek, S. Palco

Some of the negative impacts of carbon addition on the strength of castables are yet to be overcome in order to fulfill its potential benefits for oxidation resistance. This paper reports the results of recent studies conducted at CIREP on the effects of different types of carbon additives on the thermo-mechanical properties of magnesia-based castables. Experimental techniques included measurements of the hot modulus of rupture (HMOR), hot modulus of elasticity (HMOE), as well as the wedge-splitting test (WST). The comparison of evolving microstructures was carried out employing scanning electron microscopy with microanalysis attachment (SEM/EDS) and X-ray diffraction (XRD). HMOR values of 12 MPa at 1300°C have been reached in MgO-Si02-C castables containing up to 7% carbon.

Jan 1, 2004