Search Documents

By S. Sagar

In September 1996, Dofasco commissioned a 165 Mt twin shell EAF furnace and an associated ladle fleet. During and after this startup, refractory performance in the ladles was optimized on a holistic approach through several initiatives that increased ladle refractory retention times from 7000 to over 16000 mins (160 heats). This dropped the overall refractory costs by 40% while ensuring a consistent and predictable ladle performance. One initiative that drove enhancements was the proper brick selection for each particular refractory area and it's process conditions. The work concentrated on the selection of a resin bonded alumina magnesia carbon (AMC) brick in the barrel area of the ladle, upgrades to the 2 piece monolithic alumina cast ladle bottom and increasing the slagline refractory brick quality with the appropriate zoning/paneling. The adoption of a magnesia alumina carbon (MAC) brick in the transition area of the barrel/slagline has also improved performance and predictability. The design developments have lowered the overall wear rates and balanced the service life of the entire ladle. Safety was improved and breakout potential reduced by changing the safety lining from a high alumina brick to a state of art technology - monolithic shotcrete lining. This initiative decreased the overall manpower required to brick a ladle and increased shop ladle availability. The ladle bricking area environment was also improved by adopting a post combustion device to burn phenol fumes from ladle preheating practices. This has improved the overall health & safety of the reline teams. The consistent and predictable performance of the ladle on a whole has allowed the shop to decrease the number of working ladles in operation from 5 to 4. This further decreased wear rates from over-oxidation and excessive thermal cycling, saving approximately $500,000 in natural gas from pre-heater operations.

Jan 1, 2004

By Frank Wright

"The Icon Sullivan Joint Venture ore deposit was discovered in June, 1965 by Messrs. Paul Benard, Bob Galipeau and Mac Watson working under the direction of Mr. Andrew J. Troop, as employees of the Icon syndicate. The deposit is located on the Waconichici River as the south end of Baie du Poste of Lake Mistassini, approximately 45 miles north of Chibougamau. Property acquisition and Winkie drilling was followed by a diamond drilling program to evaluate the deposit. Stripping of the open pit area connnenced in the late fall of 1966 and the first test sample of ore was shipped to Chibougamau in December of that year.Regular ore shipments to the mill of Merrill Island Mining Corporation Limited for concentration commenced May 25, 1967. Production to December 31, 1970 amounts to 42,960,000 pounds of pay copper.The ore is chalcopyrite in white quartz dolomite, and it contains a very small amount of precious metals. The quartz dolomite assumes a flat to gently dipping attitude and is associated with a graphitic argillite contact zone on both hanging and footwall sides, in dolomitic limestone rocks. There is practically no other sulphide present in the ore.During the summer of 1969 a series of pre-concentration tests were completed and a Wemco heavy media sink float plant was installed in late 1969 and early 1970. This pre-concentrator eliminates at least one third of the ore mined in the form of barren quartz dolomite prior to ore shipment by truck to the concentrator in Chibougamau."

Jan 1, 1971

By T. Eger

Load Haul Dump vehicles (LHD) are extensively used in underground mining however equipment design and operating conditions contribute to restricted operator?s visibility. The inability to clearly see people, objects or hazards around the machine has contributed to a number of accidents including fatal injuries. In order to identify vehicle design characteristics resulting in restricted and blocked sightlines visibility assessments are traditionally completed in the field. However, field methods are unable to evaluate visibility under dynamic operating conditions and are limited in their ability to provide feedback on the impact of various operator characteristics such as sitting height, for example. Results of this research show computer simulation and virtual reality can be successfully used to evaluate visibility during the operation of LHD vehicles. In order to benefit from virtual reality applications the work environment, LHD vehicle and human posture need to be represented as accurately as possible. A computer simulation program with ergonomic ana lysis features, Classic JACK 3.1, was successfully used. Threedimensional CAD models of LHD vehicles were developed from manufacturer specifications and pictur es taken from LHD vehicles currently in use. The LHD models were imported into the JACK environment, a digital human was positioned in the cab of the LHD vehicle and the vehicle and human where driven over a typical mine route. Real-time feedback in the JACK program was used to identify what the operator could see under different operating conditions. Machine characteristics and operating scenarios resulting in impaired visibility were successfully identified with this method. The JACK program can also provide real-time feedback on the human?s joint forces and torques, strength requirements, postural comfort, and metabolic energy expenditure. As a result, this method could be used to successfully evaluate musculoskeletal injury risk factors along with system design recommendations to improve workplace safety and productivity in any setting. The LHD VRML files imported into JACK have also been combined with environment files into other VR software packages (e.g. Maverik) to view in a VRL facility, managed by MIRARCO at Laurentian University. The VR models using these packages can be viewed in stereo to provide better appreciation of spatial visibility issues.

May 1, 2003

By F. Parada Luna, F. Parada Torres, J. Salvo, A. Reghezza

In the pyrometallurgical processes of copper concentrates, arsenic is preferentially concentrated in the dusts carried by the gases as a result of their volatility and subsequent condensation in the gas cleaning train. In this work results obtained by alkaline leaching of the dusts from Ministro Hales roasting plant, belonging to Codelco, are presented. For the Ministro Hales plant the alkaline leaching would be an alternative to the recirculation of dusts to the roasting furnace. The experimental study considered NaOH and NaOH plus NaHS leaching of two samples of dusts, with 4.24 and 2.55% arsenic respectively. The results show that it is feasible to extract 90% of the arsenic and 50% of the antimony at room temperature using only NaOH, and when the temperature increases to 95ºC, the extractions of As and Sb increase. Copper remains in the solid residue with less than 1% dissolution, and the NaOH net consumption was approximately 140 kg/t of dust. In leaching tests with NaOH + NaHS, two types of methods were tested, baking plus leaching with water and direct leaching with a NaOH+NaHS solution. With the second method arsenic extraction increased to 95% and copper dissolution was less than 0.01% at 85ºC, NaOH 100 g/L, NaHS 90 g/L, 1.5 h and L/S ratio of 5/1 (L/kg). The bismuth remains stable in the solid in all cases. INTRODUCTION The presence of arsenic in copper concentrates has increased with time and the environmental regulations are becoming increasingly more stringent. In concentrate treatment pyrometallurgical plants, most of the arsenic is volatilized condensing in the gas train and is collected along with the entrained solids to form the flue dusts. Under these conditions, in smelters of copper concentrates with high arsenic content, the dusts are being treated in hydrometallurgical plants to extract and stabilize the arsenic, which also means that most of the copper contained in the dust is co-extracted with the arsenic. This affects the recovery of copper in the smelter and an alternative such as the selective alkaline leaching of arsenic, would allow the copper from flue dust to be recovered.

Jan 1, 2019

By Carlos Nieble

Ferteco Mineracao, belonging to the CVRD group, is one of the several iron ore mines in the south east of Brazil. Some of these mines have pit walls of over 350-m height and operations under difficult geo-technical conditions are steadily increasing. In order to mine the 15 million tonnes of high grade hematitic ore remaining in the Fabrica pit, Ferteco had to deal with the following restrictions: Warrant power to its concentrator and pellet plant, relocate the load-out rail road loop, stabilise a poor phillyte slope, relocate a creek on a bench, lower the water table and mine at maximum angles at a slope with phillyte and loose itabirites directly under the rail road loop. Considering these aspects, 3 stages of operations were designed, considering a safe operation, but with the lowest possible security factors at the last mining stage, before the pit would be filled in again with tailings. Stage one above the rail road loop and below the high tension power mast, where the poor phillyte slope was secured by a flexible retaining wall, using old rails and anchors up to 27 meters (80ft) with a working pressure of up till 30 tonnes and stage two with different slope angles, and deep wells, high wall blasting perpendicular to the highwall with relief holes and rerouting the creek in steel half culvert and stage three, the filling in with tailings and recuperation of the deep well pumps. Following studies and analysis were made: Geotechnical and geological studies of all rock formations including rock strength test, a hydrological study to define the lowering of the ground water level, slope stability analysis for every bench and all possible combination of benches, definition of blasting parameters close to the pit slope, a monitoring plan, including topographical movements, vibrations due to blasting, piezometers and pressure cells as well as a plan how to fill up the pit again with tailings in combination with the rising of the ground water level. A close co-operation between the geo-technical consultant, pit operations, the blasting contractor and the geological department resulted in an operation without any incidents, lowering the pit with an additional 3 benches and mining an additional 5 million tonnes of high grade ore.

May 1, 2003

By J. G. Pharoah

Over the last two decades a variety of models for solid oxide fuel cells (SOFCs) have emerged ranging from one dimensional (1-D) to 3-D models, from steady-state to transient models; single- and half-cell and entire stack models. A majority of these models have focused either on the transport processes or on the chemical/electrochemical processes. The approach taken by our research group is to develop a comprehensive SOFC model framework based on the considerations of detailed electrochemical reaction mechanism and by accounting for complex transport processes occurring in the porous media at the micro-scale level. In this paper, we review the state-of-the-art in SOFC modeling and identify the existing gaps that need to be filled in.

Jan 1, 2005

By Xuanxue Mo, Zengqian Hou

"Yidun Island Arc in Sanjiang Region is one of the important Kuroko-type volcanogenic massive sulfide deposits (VMS) districts in southwestern China. Tectonically, the region is situated in the eastern portion of the Tethys orogenic belt, and is a late Triassic extensional island-arc. The island-arc underwent earlier arc construction, intra-arc rifting, later arc construction and backarc spreading during its evolution and formed a complete trench-are-basin system, i.e., the Ganzilitang suture zone, forearc basin, outer are, intra-arc rifting zone, inner arc and back-arc basin from east to west across the island-arc.Kuroko-type VMS deposits and occurrences discovered so far are limited to within the intra-arc rifting zone of the Yidun Island Arc and tend to occur in groups or clusters distributed in separate faultbound basins; e.g., Zengke, Gacun and Xiangcheng basins, in which submarine volcanic rocks, especially bimodal volcanic suites, were extensively developed. The VMS deposits formed in the waning stages of volcanic eruption in the late Triassic and are hosted in the uppermost section of acidic volcanic rocks (rhyolitic-dacitic) within a bimodal suite. The orebodies are associated with these host rocks: rhyolitic-dacitic pyroclastic rocks and exhalites and chemical sedimentary rocks.All VMS deposits in Sanjiang are of the Zn-Pb-Cu type. The architecture of the deposits is twofold, consisting of concordant lenses and layers of massive sulfides and an underlying discordant stockwork. All deposits show metal zoning. The hydrothermal alteration related to mineralization is strong and asymmetrical, and is found dominantly within the stockwork zone and host rocks surrounding the ores. There are two alteration patterns: (1) chloritization - sericitization - silicification from outer sides to core of the alteration pipe; and (2) silicification + sericitization - silicification + carbonate from the lower to upper part of the alteration pipe.The mineralization temperatures of ore-forming fluids vary in the range 200°C to 335°C. Thermal evolution of the fluids displays temperature profiles that first increase and then decrease with progression of mineralization processes. The majority of black-ore minerals (Groups I and informed during intensifying stages of hydrothermal activity, and the majority of semi-yellow-ore minerals (Group III) formed during a thermal maximum. There followed the formation of fine-grained black-ore minerals (Group IV), which interacted with barite layers during decreasing temperature phases.Oxygen and hydrogen isotope studies show that the sources of ore-forming fluids for the Kurokotype VMS deposits are two-fold: seawater and magmatic hydrothermal solutions, represented by the Kuroko deposits in Japan and Kuroko-type VMS deposits in Sanjiang, respectively. In the latter case the hydrothermal solutions reacted with host rocks and mixed with cold seawater percolating downward, and circulated through volcanic rocks resulting in development of alteration zones and formation of ore minerals in Kuroko-type VMS deposits."

Jan 1, 1993

By Z. D. Hora

has been no commercial production of either perlite or pumice in British Columbia. Several promising occurrences are known to exist but their development has been delayed due to difficult access and / or remote locations. The Empire Valley perlite deposit is located 120 km east of Clinton. The deposit appears to be a flat-lying volcanic flow 50 to 70 m thick that is part of an Eocene rhyolite and dacite volcanic assemblage. The Francois Lake perlite deposit occurs on the north shore of Francois Lake where perlite is part of a rhyolitic volcanic sequence. The exposure of perlite is about 13 m thick and is considered to be Eocene or Oligocene in age. The Uncha Lake perlite deposit is located about 5 km south Industrial Minerals in Canada of Uncha Lake. Perlite appears to be intercalated with porphyritic rhyolite flows that are comparable to those at Francois Lake. Showings are widespread but poorly exposed and thicknesses are unknown. The Mount Meager pumice deposit is located in the Lillooet River valley at the base of Plinth Mountain. Coarse pumice agglomerate forms a large talus slope that is undercut by the river. Unsorted, angular fragments up to 50 cm in diameter are intermixed with up to 30 per cent of sand and silt-sized particles. The exposed zone is about 200 m long and 50 m high; it is being considered as a source of lightweight aggregate.

Jan 1, 1984

By W. T. Boyes, J. M. Harrison

"Squall Lake Gold Mines, Limited, owns a group of claims at Squall lake, northern Manitoba, about 75 miles east of Flin Flon and 3 to 4 miles north of the Nor-Acme mine at Snow lake. Gold mineralization was discovered in this locality several years prior to 1944, but it was only in that year that a comprehensive examination of the occurrences was begun. Development work to the end of 1946 has been encouraging and the deposits show interesting relations to rock structure.GEOLOGICAL SETTINGThe gold occurs in a sill of biotite-hornblende diorite at or near its contact with gneisses derived from arkosic sediments . In detail, the contact between the diorite and the arkose to the southeast of it is irregular, with interfingering of the two rock types. On the northwest side of the sill, between it and Squall lake, the rock is staurolite schist (see accompanying sketch-map).Several mineralized shear zones are known, of which those shown are the most important. Within the zones, the diorite is silicified and somewhat carbonatized. Fairly coarse arsenopyrite is the chief sulphide mineral in these zones but, locally, they contain also pyrite and pyrrhotite. Where quartz and chlorite are present, rather coarse gold is associated with them. In that part of the main zone where gold assays have been most consistent, the diorite is rich in albite."

Jan 1, 1954

By A. Chaisantikulwat

Most solid-oxide fuel cell (SOFC) modeling emphasizes steady state cell operation. However, understanding the dynamic behavior is essential to predict the performance and limitations of SOFC power systems. In this work, we demonstrate a dynamic model of a SOFC, and we simulate a feedback control scheme that can maintain output voltage despite load changes. Dynamic response is determined as the solution of coupled partial differential equations derived from conservation laws for energy, mass and electric charge. From such a model, the step responses to system input variables can be determined. Low order dynamic models that are sufficient for feedback control design can be derived from the step responses. The development of the partial differential equation model is outlined, and the limitations of the control system are discussed.

Jan 1, 2005

Resistance spot welding is the most common type of welding in the automotive industry. In RSW the size and shape of welding nugget is one of the most effective factors on mechanical properties, such as tensile shear strength and fatigue strength. so properly adjusting the variables of the welding is necessary .in this study the effect of different parameters of RSW including time, current, electrode force, geometry of electrode so diameter and angle of electrode tip in the shape and size of welding nugget evaluated. for experimental procedure, low carbon steel sheet st12 is used. the process is simulated with finite element method by using ANSYS software. for the formation of welding nugget a 2 dimensional symmetrical model electrical-thermalmechanical is used and for elevate the accuracy ,we determined the properties of material related to temperature. The results show that increasing the time and current of welding, the diameter of spot weld also increased and the role of current is more impressive. and also increasing the electrode force decrease the diameter of the nugget due to increasing the contact area and decreasing the resistance .increasing the diameter of electrode tip cause increasing contact area and decreasing the resistance and decreasing the diameter of the nugget. furthermore, changing tip angle and electrode diameter don't show sensible change in the geometry of the welding nugget. comparison between simulation and experimental result show a good adaption.

Oct 1, 2011

By A. Valenzuel

Arsenic is a common impurity in copper sulfide concentrates treated pyrometallurgically, which inevitably during the smelting-converting process reports in the final copper product affecting its properties, but also it is a very toxic occupational hazard. Arsenic recovery or disposal from concentrates or arsenic-containing copper smelter dusts have been practiced in the metallurgical industry for many years. It has been recovered principally as arsenic trioxide by roasting or leaching then precipitated. On the other hand, several hydrometallurgical processes have been developed and implemented in smelters to remove it from arsenicbearing dusts and stabilize it prior to disposal in the form of a solid compound, either as calcium arsenate, arsenic sulfide or ferric arsenate. This paper reviews the methods implemented for arsenic recovery worldwide and arsenic disposal in the metallurgical industry.

May 1, 2001

By G. B. Harris

A process for the recovery of copper from the waste oxide copper of a mined-out sulphide orebody is described. Hydrometallurgical recovery of copper from this and similar wastes has been tried several times previously without success. Leaching is carried out by sulphuric acid in columns under conditions that minimise the iron content of the pregnant leach liquor, and copper is then recovered by ion exchange rather than the more conventional solvent extraction. The resin is stripped by spent electrolyte and copper is electrowon. Results are presented for testwork originally carried out in 1993, and repeated in 2006, and the novel aspects of the process, leaching and ion exchange, are discussed. Finally, preliminary order of magnitude capital and operating costs are given, demonstrating that the process is cost effective.

Jan 1, 2007

By Blandine Arseneault

The Raglan Mill had been in production for less than a year when the initial toxicity tests on the effluent revealed that it was defined as ?toxic? under regulations. Testwork was begun to address the fundamental reasons for the toxicity and a systematic approach was initiated to identify causes. Elimination of the problem presented a challenge once the main conclusion identified high dissolved solids as the principal culprit. In particular, normally benign soda ash (sodium bicarbonate) reagent additions used in milling, was identified as the main contributor to the problem. Following analysis of all requirements and safety considerations, a concept to recycle 100% of the mill process water was pursued. In addition to meeting regulatory requirements, this project would have numerous positive benefits to the operation, including reducing fresh water consumption and lowering costs.

Nov 1, 2002

By K. Shitogiden, Y. Samada, T. Miki

Steelmaking slag contains nutrition such as Si, P and Fe for acceleration of phytoplankton growth. Phytoplankton can fixate carbon dioxide more than any other species on earth. Hence, suppression of CO2 can be achieved by applying the potential of steelmaking slag as the nutrition for their propagation. When it is considered to supply nutrition from steelmaking slag to seawater, we must avoid dissolution of hazardous elements or change of pH of seawater by steelmaking slag addition into seawater. The protection against dissolution of fluorine into artificial seawater has been studied based on dissolution behavior of steelmaking slag and synthesized substances into artificial seawater in the present work. The dissolution mechanism of fluorine from steelmaking slag and buffering action of pH change are discussed by using stability diagram in seawater.

Jan 1, 2004

The Boleo project is located in Mexico close to the town of Santa Rosalia on the Baja Peninsula. The Boleo deposit contains copper, cobalt, zinc and manganese values as oxides with minor sulfides. The Boleo deposit is metallurgically challenging due to: 1) the requirement to recover four separate metals; 2) the presence of high levels of clay in the deposit resulting in difficult solid-liquid separations, and; 3) the need to use seawater for the bulk of the processing. Baja Mining, Bateman Engineering and SGS Lakefield Research have collaborated to develop and test a process flowsheet to recover copper, cobalt, zinc and manganese products at Boleo. The key steps in the flowsheet are: ? Feed preparation (scrubbing and ball milling of oversize) in copper raffinate ? Ore leaching using oxidative and reductive leaching ? CCD washing using high rate thickening technology ? Copper SXlEW ? Treatment of a bleed solution for cobalt, zinc and manganese recovery The process for cobalt, zinc and manganese recovery involves iron and aluminum removal followed by cobalt/zinc bulk extraction using CSIRO's DSX solvent extraction system and selective zinc and cobalt stripping. The zinc strip solution is evaporated to produce zinc sulfate monohydrate crystals to market and cobalt is recovered via a further SXlEW process as high purity metal. Manganese is precipitated as manganese carbonate from the DSX raffinate solution. This paper will review the Boleo process flowsheet and provide detailed results from the 2006 pilot plant operation conducted at SGS Lakefield in Canada.

Jan 1, 2007

By A. A. Sirkeci, M. Tarkan, N. Acarkan, O. Kangal, G. Bulut

This investigation deals with the evaluation of the tailings of the Kirka Borax Plants. In this respect boron in the tailings was recovered and the utilization of the clayish fraction was investigated. There are five tailings ponds in Kirka four of which are used for the tailings of the borax concentrator and the remaining one is used for the tailings of the sodium penta-borax plant. Experiments were conducted with samples taken from ponds containing coarse fraction and fine fraction. Coarse fraction of Borax Concentrator were screened through a set of sieves. The fraction above 1 mm was removed with 41.5% recovery and 33.3% B203 content. Scrubbing was applied above 0.1 mm and products containing 32 to 34% B203 were obtained with recoveries around 35%. The tailings of sodium penta borax plant was also screened and it was found that 15% of boron reported to +1 mm size fraction with 35% B203 content. Sample containing fine tailings was treated by cycloning. The cyclone overflow was found to be below 6µm and it was separated to be used in the subsequent tests. The usage of cyclone overflow in paper, ceramics, glass, pigment and drilling industries was investigated. Since this fraction is mainly composed of carbonate minerals rather than clay minerals it was suggested that it may be used for construction and moulding purposes. Furthermore, the B203 content of the cyclone overflow was reduced to 2.4%.

Jan 1, 2004

By P. Au, R. Kearsey, D. Y. Seo, Patnaik. P. C.

Three nickel based superalloys (7.5%Cr+5%Co+2%Mo+1%Ti+5%Al and Ni balance (wt%)) containing different amounts of W and Re were produced in the single crystal (SX) condition utilizing the Bridgman casting process. First, the effect of different levels of Re, and W on chemical microsegregation were investigated by EPMA quantitative analysis, and eutectic phase fraction analysis. Second, in order to investigate the effect of these refractory elements addition on oxidation behaviour, isothermal oxidation testing of the SX nickel based superalloys was conducted at 1000°C for 277 hours under 3 ppm moisture content of air in a thermogravimetric analyzer (TGA). All three SX nickel based superalloys revealed an excellent SX solidification structure with a common primary dendrite arm spacing of -250 µm and a large fraction of ?/?' eutectic located between the secondary dendrite arms. From the average EPMA compositional results, with the exception of Ni, elements such as Cr, Co, Re, Mo, and W all tended to segregate towards the dendrite core during solidification, while Al, Ti, and Ta were present in greater quantity in the last liquid phase to solidify, which resulted in large eutectic ?/? ' phases to form within the interdendritic regions. As the nominal level of Re increased, microsegreagation of Re, W, Cr and Mo increased, indicating that Re had a much greater influence on partitioning behavior compared to W. Figure la shows the specific mass gain as a function of exposure time for each alloy. An alloy with 2wt% of W and Re (Alloy B) exhibited less weight gain compared to two other alloys with either higher content of W or Re (Alloy A and C). Microstructural and compositional analyses of oxidized samples were conducted using SEM and EDS. Figure lb shows the typical surface morphologies of the oxidized Alloys A and B. It is evident that more oxide nodules (indicated by arrows in the figure) were presented in Alloy A. It is speculated that the amount of these nodules was responsible for more mass gain in Alloy A compared to the two other alloys. From the examination of the longitudinal section of the oxidized samples as shown in Figure 2, for Alloy A, nodules actually penetrated deep into the material. For Alloy B, however, a relatively uniform and continuous oxide layer was developed and deeply attacked areas were not observed. It was also found that preferential oxidized regions were located at the area between the ?/?' eutectic phase and the dendrite arms where the concentration of refractory elements was relatively high. Therefore, it is plausible that the oxidation kinetics of these alloys is related to the extent of microsegregation.

Jan 1, 2004

By Karim Ramji

The extractive sector today faces growing social, legal and political risks (SLPs) from so many different stakeholders including national and local governments, name and shame groups, civil society and environmental groups, and the ?Occupy? movement. Beyond these stakeholders, there are the indigenous peoples who have growing legal, social, political and economic influence which can often determine the outcome of the Project. The development curve in the extractive sector from initial exploration to mine start-up has become longer, steeper and more risky and expensive as these SLPs have grown in scope and complexity. Even if a project is permitted or starts commercial production, its ongoing development and operations are also facing these SLPs. The continuous assessment of these SLPs and the strategy to mitigate for them has now become critical for every project in the extractive sector. A project will only be successful if it is able to obtain the legal permits to operate, then withstand any judicial reviews, and then also to be able to gain and maintain the Social License to Operate (SLO). Stakeholder identification, management and engagement are key risk-mitigation tools. This paper focuses on the growing influence that indigenous peoples are now enjoying and the impacts on the extractive sector. Indigenous peoples are a unique stakeholder group because their legal rights and interests to lands and resources, their aboriginal title and rights, are gaining more recognition. When indigenous peoples form alliances with other stakeholders, this simply adds to their growing momentum and leverage, and this can become a daunting challenge for the extractive sector. More due diligence is required by companies to understand and assess the challenges posed by operating in areas claimed by indigenous peoples. There is a real need for mining companies to develop an effective indigenous engagement strategy to address these challenges in order to successfully convert risks into opportunities. Early identification and engagement with the indigenous peoples is required and the goal should be to conclude an Impact Benefits Agreement (IBA) with the affected indigenous peoples. The real objective must be to develop a real and transparent relationship between the company and the indigenous peoples so as to gain and maintain the SLO.

Aug 1, 2013

By S. K. Sadrnezhaad, B. Hashemi, Z. A. Nemati, Z. Moghimi

Based on the kinetics relationships of a solid - gas model, a software was developed for the prediction of oxidation. Preliminary prediction of oxidation by the software and experimental results of MgO-C refractories were studied and compared. By using the obtained data from this approach, the effective diffusion coefficient, intermolecular diffusion coefficient and diffusion activation energy in the MgO-C refractories, containing various amount of graphite were obtained at different temperatures. First of all, the prediction by the software was very compatible with experimental results, for different oxidation mechanisms in the MgO-C refractories. The results showed that pore diffusion is the predominant oxidation mechanism in this system. The results indicated that when graphite content was above 10wt%, the intermolecular diffusion coefficient was independent from graphite content, and it was closed to a constant value at each temperature.

Jan 1, 2004