Search Documents

By Stephen Hardcastle

Personnel Heat Exposure Issues In Canada?s Deep Mechanized Mines ?Project developed in 2004 ?Base/precious metal industry identified heat stress/management as a major challenge affecting productivity and operating costs ?Project started in 2005 ?Current research nearing completion ?Guidelines, further data analysis and ?Communicating the Science? will continue into 2011

Oct 1, 2010

By Franco Chiesa, David Levasseur, Bernard Duchesne

A 500kg aluminium AlSi7Mg03 casting has been poured and the metallurgical quality at different locations inside the casting has been thoroughly investigated. It included measuring the local tensile properties (YS, UTS, El) in the T6 condition, the dendrite fineness (DAS) and the level of microporosity. A correlation was found between the microporosity level, the local solidification time and solidus front velocity; this correlation allows to predict the porosity level in large aluminium castings (solidification times between 20 and 200 minutes). Quite expectedly, properties varied widely within the casting and the actual mechanical properties were much less than the "textbook values" based on measurements carried out on separately cast standard specimens. A correlation between the secondary dendrite arm spacing (DAS) and the local solidification time was in keeping with previously published data. Finally the conditions to obtain an acceptable finish on machined surface were determined.

Jan 1, 2014

By Qidong Xu

Abstract - The metavolcanic rocks of the Dahongshan area have been subjected to both widespread hydrothermal alteration from circulating seawater and to regional metamorphism, such that their mineralogic and chemical compositions have been changed significantly. Studies of immobile elements show that these rocks were originally tholeiitic basalts with geochemical characteristics of T-type MORB formed in a mid-ocean ridge environment. The accompanying Cu-Fe-rich VMS mineralization is in keeping with the original petrology and tectonic setting of these metavolcanic rocks. Regional alteration evident in K-Mg enrichment is related to sericitization and chloritization. Local alteration associated with Cu-Fe mineralization appears to have been accompanied by Si enrichment and Na depletion. P enrichment identifies metasomatism related to Cu-Fe reconcentration in the mineralized zone.

Jan 1, 1999

By Greg Collins

BUCKO EXPLORATION HISTORY ??1964-Discovery ??1970?s -114 holes totaling 34,000 metres drilled -vertical shaft excavated to a depth of 300 metres (1000 Level) plus 800 metres of underground development -Exploration program cancelled due to Falconbridge economic issues ??1990?S-19 holes drilled totaling 9,600 metres ??2000 -13 hole 4,600 metre exploration program by Nuinsco Res.

May 1, 2006

By B. A. Watters, G. A. Parslow, F. H. Mcdougall

Carbonate-rich rocks occur at several localities within the Flin Flon volcanic sequence of the eastern Amisk Lake area. The rocks occur in two areas: as a group of small occurrences on islands within Amisk Lake and as two much larger linear belts running parallel to the regional structure east of Amisk Lake. Mineralogically, the rocks consist of talc and Ca-poor ankerite with occasional graphite. Segregation of these minerals and colour variation impart a well-defined planar fabric to the rocks and where the units are fairly continuous (e.g. Mosher Lake), their trend and attitude suggests a concordant relationship to the volcanics. Major and trace analysis of22 samples confirms the presence of two types, with one type being represented in each of the two areas. Most of the elements studied can be used to characterize the two groups, but three elements in particular give a clear separation: Mg, AI and Ni. Recalculation of the major element analyses, on a water and carbonate-f ree basis, indicates that one group (large concordant bodies with high MgO, high Ni and low AI20.J is altered ultrabasic material of peridotitic or dunitic composition. Because no relict igneous material is observed, and the contacts are apparently very sharp, it is possible that the hydration-carbonization process occurred simultaneously with intrusion, .in a closed system. The other group (small occurrences with relatively low MgO, low Ni and high AI203J represents alteration of basaltic rocks. AIthough some analyses suggest the introduction of calcium, as carbonate, along with the volatiles, the major oxides have remained remarkably stable during the alteration process(es).

Jan 1, 1981

By Fritz F. Prugger

In August, 1970, during routine shaft grouting, a major water source was intersected. Water and quicksand under very high pressure entered the shaft at a rate of 65 m3 per minute. The mine and both shafts were flooded. The breach was sealed simultaneously from within the shaft and through a relief hole drilled from surface. The mine was dewatered, rehabilitated and the equipment was restored. Production resumed two years after the accident.

Jan 1, 1979

By V. Nudo, R. del Villar, A. R. Laplante

"Fine iron ore recovery from the tails of Les Mines Quebec Cartier was investigated using Reichert trays and spirals. The effect of feed rate, density and splitter setting on the performance of rougher, cleaner and recleaner stages of a 2DS tray assembly was determined using 2- and 3- factorial experimental designs. The tray concentrate, assaying 27% Fe, was further upgraded by spiral to yield a concentrate assaying 55% Fe. Further laboratory scale testing showed this material to be easily upgraded to 65-66% Fe with high Fe recoveries.This paper presents the metallurgical results of the three tray stages. The model used to predict the performance of a full recovery circuit is then described. Simulation results are presented and their reliability assessed. Finally, an economic evaluation of the proposed scavenging circuit is summarized.INTRODUCTIONThe Mount Wright plant (UWP), located near Fermont, Quebec, processes daily 130,000-150,000 tonnes of iron ore assaying between 27 and 33% Fe, to upgrade it with three stages of 44.5 cm pitch GEC spirals to 66% Fe, while rejecting approximately 80,000 tonnes assaying between 6 and 11% Fe (1-3). Heavy liquid separation (at 3. 3 g/mL) of the plus 37 µm fraction (+400 mesh) of the tails reveals that a significant fraction of the iron is in the sink product, below 150 pm (100 mesh), as shown in Table 1. Also shown is the iron grade of the sink and float fractions. The high grade of the fine sink indicates that hematite ls well liberated below 105 µm (150 mesh), as previous studies have shown (4,5). The iron grade of the floats is very low in the fine size range, but increases with increasing size above 105 pm, because of incomplete liberation. Overall, two thirds of the plus 37 µm iron ls in the sink product, which constitutes less than 10% of the total tail."

Jan 1, 1987

By W. Lamb

Feed Preparation ? Five primary parameters affect the screening efficiency ? Ore characteristics ? Operational characteristics ? Screen characteristics ? Water addition and washing ? System design

Apr 1, 2005

By M. R. Henzinger, W. Schubert

"The quality of the backfill applied at a shield driven tunnel is of significant importance failure of the lining. The used material also affects the interplay between support and excavation behaviour.In this research the state of the actual bedding situation is investigated by an analytical approach, laboratory tests and numerical simulations. The numerical simulation using continuum methods have shown shortcomings. These shortcomings regarding the instability of large strain simulations restrict the possibility to reproduce the relocation of the backfilling material. The performed scaled model tests have shown that the regripping process of a double shielded tunnel boring machine affects the soil failure within the gap. With the analytical results the influence of the wall friction can be predicted. Therefore the angle of the failure surface can be determined. The results have shown that the wall friction significantly increases the failure angle. INTRODUCTIONFor tunnel boring machines (TBM) with single (SM) or double (DSM) shield, precast liningsegments are used as rock support. These segmental linings are installed within the protection of the TBM shield. In order to reduce the friction while advancing, the shield diameter is smaller than the diameter of the cutter head and therefore also smaller than the excavation boundary. The difference depends on the expected radial convergences. Since the lining segments are mounted within the shield the steering gap between the shield and the excavation boundary increases and is hereinafter called annular gap.In the process of tunneling in hard rock, the annular gap is usually filled with fine grained and closely graded gravel, termed as pea gravel. The backfilling process starts as soon as possible after the shield tail passes the lining. Due to the operational procedure within the working area of a TBM, a fully backfilled annular gap might not be established after every ring closure. This leads to an unfavorable distribution of the pea gravel leaving the segmental lining partially without bedding. Segmental linings can develop sufficient resistance only when properly bedded."

Jan 1, 2015

By F. Sheykh-Jaberi, S. L. Cockcroft, A. B. Phillion

A coupled fluid/structure model has been developed to simulate semi-solid deformation in an industrial aluminum casting alloy, A356. Although this alloy has a significant eutectic fraction, nearly 50%, it still shows susceptibility to hot tearing. The model geometry consists of solid grains, created from a Voronoi tessellation of the domain, surrounded by liquid. The simulation is performed using the commercial codes, Abaqus Standard and Abaqus CFD. The solid model calculates the velocity, stresses and distortions in response to an applied uniaxial strain, and transmits them to the fluid-flow model, which computes the velocity and pressure fields in the liquid. It was shown that grain size and configuration, fraction solid and fluid properties all affect the semi-solid deformation behaviour.

Jan 1, 2014

By J. L. Blaylock

Normally, the hydraulic system and structures are considered to be unrelated items. In reality, the two cannot be separated because one affects and depends on the other to function properly. This paper explores the potential failure areas of hydraulic cylinders, and suggests possible methods to prevent failures from occurring. The use of high-strength low-alloy steel in frames is reviewed and the benefits discussed. Fabrication techniques and handling of material are noted in the hope that this knowledge will aid in the repair of frames in the field.

Jan 1, 1979

By K. P. Plucknett, Z. Memarrashidi

WC-Co ‘hard metals’ are widely used in a variety of industrial applications due to their resistance to abrasive wear, in addition to their high hardness and toughness. However, in contrast to their mechanical properties, the corrosion response of these materials is relatively poor. In the current work the corrosion mechanisms of two WC-Co cermets are analysed, with 10 and 30 vol. % of the Co metal binder, in a 3.5 wt.% NaCl aqueous solution. The assessment of corrosion involved a variety of electrochemical measurements, including open circuit potential, potentiodynamic polarisation and cyclic polarisation, together with systematic analysis of the post-corrosion solution chemistries using inductively coupled plasma optical emission spectroscopy. The corrosion potential and current density were determined, following Tafel extrapolation, allowing the calculation of the corrosion rates. It is demonstrated that continuous dissolution of the cobalt phase occurs during corrosion, which is a result of poor cermet passivation behaviour, and this response increases with the amount of binder in the cermet.

Jan 1, 2015

Fiabilité Totale d?Usine (FTU) Plan de la présentation ?Théorie de l?entretien ?Analyse comparative juin 2005 ?Session de travail 2005-2006 ?Suiviet Résultats(IndicateursdePerformance)

Feb 1, 2008

By H. K. Olsen, B. Thomassen, H. K. Schønwandt, L. Grahl-Madsen, H. Stendal

Abstract-The central part of the early Proterozoic Ketilidian orogen in South Greenland consists of an I-type granitoid batholith transected by four regional NE-SW-trending shear zones. The batholith was probably emplaced during subduction, from the south toward the Archaean craton in the north, in a sinistral transpressional system. A regional sediment sampling program covering 5000 km2 shows a close connection between a gold-mineralized trend and one of the major shear zones within the epizonal facies of the batholith. The gold mineralization is not directly related to the major shear zones, but occurs in quartz-veined and silicified second-order structures. High-grade (up to 114 ppm Au over 6 m) low-tonnage mineralization is found within these second-order structures cutting both amphibolites and granitoids. The mineralization is characterized by negligible or small alteration halos. Gold is associated with various element combinations of enhanced As-Bi-W- Cu, which indicate that the mineralization is mesothermal in origin.

Jan 1, 1995

By H. K. Olsen, B. Thomassen, H. K. Schønwandt, L. Grahl-Madsen, H. Stendal

The central part of the early Proterozoic Ketilidian orogen in South Greenland consists of an I-type granitoid batholith transected by four regional NE-SW-trending shear zones. Thebatholith was probably emplaced during subduction, from the south toward the Archaean craton in the north, in a sinistral transpressional system. A regional sediment sampling program covering5000km2shows a close connection between a gold-mineralized trend and one of the major shearzones within the epizonal facies of the batholith. The gold mineralization is not directly related to the major shear zones, but occurs in quartz-veined and silicified second-order structures. High-grade(up to 114 ppm Au over 6 m) low-tonnage mineralization is found within these second-order structures cutting both amphibolites and granitoids. The mineralization is characterized by negligible or small alteration halos. Gold is associated with various element combinations of enhanced As-Bi-W-Cu, which indicate that the mineralization is mesothermal in origin.

Jan 1, 1995

By Bernard Tougas, Franco Chiesa, David Levasseur, Bernard Duchesne

"In the present paper, the optimization of a tilt poured permanent mold will be carried out using filling and solidification modeling. This exercise resulted in 3 modifications of the initial mold design which was based on the foundry experience. The optimization provided a 20% improvement in the yield while increasing the output from 10 to 15 castings per hour.In a subsequent study, the value of the critical fraction solid of AlSi7Mg (A356) alloy was verified by radiographic analysis of the castings produced in the first 5 cycles of a run, which are necessary to bring the mold to a dynamic thermal equilibrium."

Jan 1, 2014

By G. Russo

During the construction of the S.Martin La Porte access adit, 9m in diameter, extreme squeezing conditions occurred while crossing Carboniferous schistose formations, with diametric convergence up to 2m. Back-analysis of monitoring results shows that an acceptable simulation of the observed excavation behaviour can be derived using a combined analytical and numerical approach, with simple elasto-plastic laws but a progressive reduction of residual parameters and a relevant increase of dilatancy.

May 1, 2009

By S. V. Burr

"IntroductionOne of the more puzzling geological enigmas, in the writer's opinion, is how rock can move sideways with respect to other rock. In the writer's study of regional northwest-southeast folding in North America (Burr, 1980), he may have found the answer to horizontal offset.Horizontal OffsetSideways movement or horizontal offset does not mean that the movement was, or is, horizontal. As indicated below, the actual movement may be at a high angle from the horizontal. However, it is the horizontal VECTOR, or offset, which is measured on surface by geologists. Vertical movements (thrust, normal, reverse) can be understood, as they involve blocks of rock , generally separated on four to six sides, which have been pushed up or subsided. Vertical faulting across dipping strata can produce APPARENT horizontal offsets. However, this thesis deals only with ACTUAL offsets.The ProblemFigure 1 is a plan view of a simple hypothetical horizontal offset. Three vertical dykes are intersected by a fault lineament. Two dykes exhibit no movement; the middle dyke has been offset a distance (a). Vertical faulting would have produced no horizontal offset. How can a horizontal distance (a) disappear or appear? Rock expands or contracts in infinitesimal amounts.SolutionThe map (Burr, 1980) shows the writer's interpretation of regional northwest-trending folds in Ontario. The writer made two observations about horizontal offsets during his thirty year study of these folds:1) All major horizontal fault lineaments strike at a high angle to the northwest fold axes. Many of the northwest-trending lineaments are fault s, but their movement is essentially vertical.2) Close to many of the known horizontal offsets (and several lineaments), there are areas where plunge reversals are so frequent and close together it is impossible to draw in all the fold axes at a scale of 1 inch = 4 miles, and, in the highly faulted Espanola area southwest of Sudbury, Ontario, all the indicated folds cannot be easily separated at a scale of 1 inch = 1 mile. The writer has observed folds less than 30 feet apart next to the strong Puskitamica-Chibougamau fault in northern Quebec."

Jan 1, 1982

By Bian Xue, Wu Wenyuan

In order to recycle the iron and rare earth from the Baotou tailings, a roasting method was developed involving the addition of C, Ca(OH)2, and NaOH, designed to both decompose the rare earth minerals and convert haematite into magnetite and allow its recovery. The effect of various parameters such as roasting temperature, roasting time, C addition, Ca(OH)2 addition, and NaOH addition on the reduction ratio of haematite (iron sesquioxide) and decomposition ratio of rare earth were investigated. The results showed that the reduction ratio of haematite and the decomposition ratio of rare earth could be as high as 85% and 95% respectively when the roasting temperature was 650°C, roasting time was 60 min, Ca(OH)2 addition was 4%, NaOH addition was 3%, and C addition was 1.5%.

Jan 1, 2014

By H. Tokuichi, H. Ohta, K. Sato

A physical separation technique of tantalum capacitors from waste print circuit boards is in a development phase in Japan. A tantalum capacitor consists of an exterior coating of resin (epoxy resin) mixed with silica fillers and a sintered tantalum compact, the latter of which is impregnated with manganese dioxide (MnO2). In this study, we developed a process to recover tantalum oxide from tantalum capacitors by roasting, fluidized-bed separation, and hydrometallurgical treatments. Our aim was to recover tantalum oxide with high purity from waste tantalum capacitors. In this process, the exterior resin was selectively decomposed by roasting without oxidation and pulverization of the sintered tantalum compact at a proper temperature. Furthermore, the decomposed resin with silica filler on the surface of the sintered tantalum compact was mostly removed by fluidized-bed separation. The surface of the sintered tantalum compact was cleaned by ultrasonic irradiation in an acid solution to remove the MnO2 paste as well as residual Ag paste and silica filler. The impregnated MnO2 in the sintered tantalum compact was leached as Mn(II) ions using acid solutions via the reducing effect of tantalum metal to recover purified tantalum oxide.

Jan 1, 2014