Search Documents

By J. Y. Kim, Kenneth Stowe, Stephen Chryssoulis

"A series of flotation tests was carried out on Brunswick Mining ore with various pH modifiers (soda ash, lime, KOH) and added ions (ferric, nitrate, sulphate) in the copper lead rougher circuit. The main objective was to identify downstream effects on sphalerite activation and subsequent zinc rougher flotation. Some significant differences in zinc flotation were obtained. Most notably, soda ash and nitrate ions had a positive impact and ferric ions a pronounced negative effect on selectivity.Selected products from the flotation tests were deslimed at 400 mesh, washed with methanol, air dried, placed in teflon vials purged with nitrogen and stored at -15 degrees C. Numerous liberated sphalerite and pyrite particles were selected under a stereoscope and placed in rows on indium foil. The surface compositions of the particles were analyzed with an innovative laser probe (LIMS). The very small analysis area of the LIMS enables the surfaces of individual grains to be characterized. In addition, the rapid analysis time allows a statistically significant number of grains to be analyzed quickly.Surface lead appears to play a major role in zinc activation/flotation. Possible mechanisms are proposed to explain the variations in metallurgical performance at the different test conditions.IntroductionAlthough the bulk composition of mineral grains is an important consideration for the mineral processor it is ultimately surface composition and topography (edges and dislocations preferred sites for reactions) that control reactivity in flotation and cyanidation (passivation, encapsulation and preg-robbing). Determination of the surface properties of particles from process streams poses a particular challenge for the surface chemist for a variety of reasons, including:"

Jan 1, 1994

By S. Minamiguchi

Grain refinement is effective to enhance strength and ductility of metallic materials. However this advantage has not been utilized fully for magnesium alloys in industry because microstructure control through thermomechanical treatment is difficult owing to their poor deformability. The authors proposed a high-speed heavy-reduction rolling for production of Mg alloy sheets. It was found that the deformability is significantly improved at high speed and that the thickness can be reduced 60% by one-pass operation even at room temperature without fracture at the rolling speed higher than 1000 m/min. In this study, commercial AZ31B sheets were rolled at 2000 m/min between room temperature and 350°C, and quenched immediately after the rolling. The sheets rolled at 200°C show the finest recrystallized microstructure with the mean grain size of 2.2 Rm. They show outstanding mechanical properties with the tensile strength of 293 MPa, and the elongation of 25%. It is concluded that high-speed rolling is very advantageous for grain refinement and improvement in mechanical properties as well as deformability and productivity.

Jan 1, 2006

By T. G. Joseph

The strain softening relationship developed in part 1 is now applied to coal. Having determined the post-failure stress-strain curve for coal specimens, this information can then be used in a finite element program, such as Phase 2, to examine the post failure characteristics of coal pillars. Using example data, the strength of coal pillars of different width/height ratios are estimated and compared with well-known empirical pillar size-strength relationships. In addition, the post-failure stress-strain behaviour of a coal pillar is compared with an empirical relationship reported in the literature.

May 1, 2002

By Emilie Williams

The Mouska Mine uses primarily shrinkage mining to extract the narrow veins that contain its mineralization. Mining is currently occurring on levels 12 to 14, reaching depths of 800 m below surface. Although the mine is not considered ?deep?, no backfill is available to fill empty stopes and certain areas remain open for over 500 m in height. As only narrow sill pillars remain to separate the levels, a highstress environment is created. Seismic activity was first observed when mining reached Level 11 (600 m deep) and has steadily increased since then. Seismic activity is associated with the highly-stressed sill and rib pillars; no geological structures have demonstrated significant seismic potential to date. In response to this increase in activity, pillar dimensions have been increased with depth and dynamic ground support has been installed. Seismic and pressure monitoring have been implemented, among other types of instrumentation. The following paper further describes the challenges associated with using conventional methods in the high-stress environment typical of the Canadian Shield, as well as several solutions implemented to mitigate these risks.

Feb 1, 2008

By Michael Davies

Mined Material Management Meeting or Missing the Mark? o you agree that we have the technology to consistently design robust M3 facilities? ?YES your experience do these M3 facilities perform as expected during operations? ?USUALLY hat can be done to improve performance, e.g. better communications between project and operating teams, discontinuity between design and operational input by designers, others? ?UNDERSTANDINGWHY THINGS GO WRONG an we identify the key characteristics of ?good M3 facilities?, i.e. ones that are performing well? Can we identify ?good M3 facilities?, i.e. ones that perform well and can be held up as examples? ?WITHOUT QUESTION?? your opinion, for what reason do they not perform as expected? ?NO SINGLE REASON??..

May 1, 2010

By Zhongxue Li

This paper reviews an analytical model that defines the relationship of weight-weighted or volume-weighted average haulage distance with bench height and other related parameters, presents the optimum bench heights under various conditions in terms of minimizing the weighted average haulage distance of ore/waste during the full lifetime of an open pit mine, and discusses the truck haulage economics of mining open pits by high bench, specifically by 15 m, 18 m and 20 m benches through marginal analyses. The observations from these analyses disapprove the previous conflicting assertions that the over-all weighted average haulage distance either increases or decreases directly with bench height. It is concluded that: (1) an increase of bench height to 15 m from 12 m is likely to be viable under the general conditions of large-scale deep open pit mines; (2) the reduction of haulage cost is much limited with the case of increasing bench height to 18 m from 15 m; and (3) the feasibility of mining open pits by 20 m benches is generally questionable. These conclusions may serve as a useful guide for those who advocate open pit mining by high bench.

Jan 1, 1995

By A. L. Hinde, H. Dong, J. T. Kalala

"The High Pressure Grinding Roll (HPGR) is gaining acceptance in the mineral processing industry and has become a competitive technology in reducing the specific energy consumption in Mineral processing plants. The amount of samples required for HPGR amenability testwork and HPGR wear tests is usually high and often cannot be available at early stage of projects were only a few drill cores are available.Although HPGR was initiated from small scale piston die compression tests, the development of small scale piston die test to predict the performance of HPGR has been slow.The objectives of this paper was to present the designs, operating procedure of piston-die press and operating conditions which have resulted in similar particle size distribution obtained from a piston die test and HPGR Labwal unit starting from the same feed size distribution. Testwork were conducted using a 2 MN piston-die press and a Labwal HPGR unit on major South African ore types, viz, gold, platinum and iron ores. The results obtained show that piston-die test can generate data to predict energy consumption, product size distribution, and even to evaluate the edge effect."

Jan 1, 2012

By Caitlyn J. McKinley, Ahmad Ghahreman, Maziar E. Sauber

Ever-growing global needs for critical metals, such as rare earth elements (REE), and base metals, such as copper and nickel, and their environmental impact motivated the pursuit of sustainable flowsheets. Regeneration of hydrochloric acid in chloride-based leaching flowsheets as a critical unit operation is an example of such endeavours. This study presents an efficient hydrochloric acid regeneration method from a magnesium chloride solution waste by addition of sulphuric acid in relatively low temperatures. The effects of temperature, initial magnesium chloride concentration, amount of sulphuric acid added, and airflow are examined. Experimental work are focused on temperatures between 80 and 95°C, initial magnesium chloride concentrations of 2 to 5 M, 100% to 220% stoichiometric sulphuric acid additions, and airflows between 200 to 600 mL/min. The developed technology recovers hydrochloric acid at a high rate and concentration with a relatively small environmental footprint. INTRODUCTION The mining and metals sector is under increasing environmental and economic pressure to make more efficient use of chemical reagents and energy in the production process. This affects several areas of process and flowsheet design such as the selection of the most appropriate unit operations and the overall design of the process steps paying heed to sustainability. Owing to the inherent inefficiencies of physical and chemical processes used in the mining industry, there will be materials and streams generated that are not a desirable part of the envisaged flowsheet. Thus, methods are implemented to recover and recycle such effluents. If the recovery and recycling are not economical, then procedures are followed to neutralize and dispose these effluents. In many cases, these effluents are potential contaminants or hazardous materials, and their disposal should be looked at in a much larger context. The safe management of the contaminants and hazardous effluents is a daunting problem in the mining industry and is fraught with technological, economic, social, and political challenges.

Jan 1, 2019

By F. S. Hoseinian, M. Irannajad, M. Safari

In this study, the effect of chemical interactions of materials used in ion flotation on the removal of Ni(II) ions from low concentration synthetic wastewater was studied. Sodium dodecyl sulfate (SDS) and ethylhexadecyldimethylammonium bromide (EHDABr) as collectors and methyl isobutyl carbonyl (MIBC) and Dowfroth250 as frothers were used. To investigate the effective parameters and interactions of them, 16 experiments including 6 level variables were performed by supporting DX7 software and on the bases of 2-level factorial method. In the first step, the tests were conducted in a Hallimond tube. The result showed that collector of SDS and frother of Dowfroth 250 had appropriate interaction with each other at pH = 3. In the second step, optimal results from the first step were evaluated in a mechanical flotation cell. The removal of Ni(II) ions increased by increasing the time of flotation and they have a direct relation with the water removal. The kinetics study shows that the order and the rate of removal of the reaction do not follow any of the zero-order, first-order and second-order equations. The flotation rate curve on the removal of Ni(II) ions will divide the separation process to two stages, a fast flotation rate at the first stage and a slow flotation rate at the second stage. Ni(II) ions removal was obtained 88% at the best condition.This study showed that the use of ion flotation was a very effective method for Ni(II) ion removal from industrial wastewaters.

Jan 1, 2016

By J. Brent Hiskey

At present, approximately 80 % of the worlds mine production of copper is achieved by smelting and electrorefining. The principle aim of copper electrorefining is to satisfy the large demand for extremely pure copper. It is remarkable that high quality copper cathodes with the required purity (99.99+% Cu, ASTM B115-10) and structural characteristics (i.e. deposit density and morphological texture) are produced from impure copper anodes dissolved in electrolytes containing a variety of impurities. This is accomplished with the proper control of operating parameters such as: current density; temperature; copper and sulfuric acid concentration; agitation; substrate preparation; and the application of electrolyte additives. The basic elements of the electrolysis of copper have not changed significantly over the past 150 years since the early developments of James Elkington. Importantly, our fundamental understanding of the underlying electrochemistry has advanced considerably. This is especially true regarding our knowledge of the mechanistic role of additives during the electrocrystallization of copper. This is a very complex subject and modern electrochemical techniques and the development of surface characterization and imaging instruments has helped immensely in our ultimate understanding of how additives control the deposit structure and morphology. The purpose of this paper is to review the historical development and application of electrolyte additives in copper electrorefining and to examine our current knowledge regarding their use. INTRODUCTION The first transatlantic telegraph cable was completed in August 1858. Regrettably, this cable failed shortly after the initial connections. After several more failed attempts, improvements in materials and copper quality resulted in successful communication between Europe and America on July 28, 1866. In many ways this hallmark event demonstrated the need for high purity copper. The first copper refinery in the world was commissioned in May 1869 in Pembrey, South Wales by partners Josiah Mason and James Balleney Elkington. (Historical Note). The 1865 and 1868 British patents issued to James Balleney Elkington were the foundation for the first commercial production of high purity electrolytic copper (Elkington, 1865, 1869, 1870). This important achievement was made possible primarily by the invention of the dynamo which was based on the fundamental operating principles advanced by Michael Faraday. A symbiotic relationship between copper refining and the dynamo was henceforth established. The dynamo provided electric current for electrolytic refining of copper and the electrorefining tankhouse provided pure copper which was required for the generation and transmission of electricity.

Jan 1, 2019

By Jean-Francois Magnan

"The old conventional process to produce lithium raw material dates from 1954 (CA patent #504477A). This process produces low purity lithium carbonate (Li2CO3) only. To obtain battery-grade carbonate, another polishing process is needed. To further obtain lithium hydroxide, another chemical conversion process is needed. That is why historically, the value of lithium hydroxide has always been higher than that of the lithium carbonate precursor. With the old conventional process, the low quality lithium carbonate is precipitated from a lithium sulfate solution (Li2SO4) by adding soda ash (sodium carbonate and its impurities). The resulting reaction produces significant quantities of sodium sulfate (salt cake) as a by-product with amounts larger than the impure Li2CO3 recovered with part of the soda impurities. When this conventional process was invented, the salt cake by-product was not an issue: it was discarded in a river near the plant. This practice cannot be done today in North America. While looking to find a solution for salt cake, electrolytic salt splitting of Na2SO4 into NaOH and dilute sulfuric acid appears as a technically feasible solution to get a rid of the salt cake. However, the sodium sulfate salt splitting process has difficulties to economically compete with the chlor-alkali process, which produces millions of tons of NaOH from sodium chloride (NaCl) every year.In contrast, the process developed by Nemaska to directly produce LiOH by Li2SO4 salt splitting not only solves the environmental problems related to the conventional process to produce lithium carbonate raw material, it also produces very high purity lithium hydroxide monohydrate directly at very competitive OPEX cost in comparison with industry peers (Figure 1). It also drastically reduces the amount of reagent and the direct greenhouse gas emissions."

Jan 1, 2016

By M. P. Rennick, D. M. Burton

The Murray Brook massive sulfide deposit, which was the first geochemical discovery in the Bathurst camp, is one of the largest sulfide deposits in the area. The massive sulfides are hosted by quartzose metasedimentary rocks in the lower part of the Ordovician Tetagouche Group. This thick succession of sedimentary rocks is overlain conformably by felsic volcanic rocks, and is structurally overlain by mafic volcanic rocks. The massive-sulfide body is polydeformed, but primary metal zoning is still discernable and may permit future exploitation of discrete lead-zinc and copper zones. Although it was discovered in 1956, the deposit was not developed until 1989, when Murray Brook Resources commenced processing of gossan containing precious metals. Recovery of gold, silver, and mercury is accomplished by indoor vat leaching on a year-round basis.

Jan 1, 1992

By S. Jordanov

The nature of processes that take place on top of copper bearing grains during the suppression of copper acid drainage from mine tailings was studied on a grain model. Cyclic voltammetry (C.V.) was employed as an experimental technique suitable for indirect measuring of copper leaching. Experiments were done in sulfuric acid (pH=2) at electrodes that progressively approach the real situation during acid main drainage, starting with Cu-metal, then with CuO and finally with CuO covered with CaSO4. Oxidation was found to be the only process that takes place on metallic copper electrode anodically polarized up to 2 V vs. Cu/CuSO4 reference electrode. Dissolution is intensive and reaches up to 50 mA.cm-2. When the same was repeated, but on CuO electrode, anodic currents were some 4 times lower than on the bare metallic surface. This indicates that the electrode material is not completely oxidized to copper(II)oxide and the Cu(O) or Cu(I) residues are oxidized during the anodic polarization. This explains the diminished dissolution. Dissolution is further restricted at electrodes covered with CaSO4. It is some 20 times lower than on the bare oxide electrode. When the second layer of CaSO4 was applied, anodic currents were another 15 times lower. Total decrease of anodic currents when transition is made from Cu-metal to CuO covered with 2 layers of CaSO4 reaches up to 7.500 times. C.V. measurements produced a proof that mechanical blockage is the way how lime prevents leaching of copper bearing grains in immobilization experiments referred elsewhere.

Jan 1, 2007

By Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the North American database.

May 1, 2006

By T. Crivits, I. Bellemans, K. Verbeken

In the metallurgical industry, furnace cooling is often employed to enhance furnace lifetime. Hence, the pyrometallurgical phase comes in close contact with a non-air coolant. The proximity of the pyrometallurgical phases to the coolants may lead to dangerous situations. In case of a breach of the cooling circuit, the contact between a hot and a cold liquid may cause a vapour explosion. The outcome of this vapour explosion includes a pressure wave which could result in damage to the furnace, bodily injuries or even casualties. To prevent such dramatic events, the origin of vapour explosions is currently being studied in more detail. For this purpose, OpenFOAM was used to perform Computational Fluid Dynamics (CFD) simulations. In a first step, simulations were run to get a better idea of the influence of the compressibility on the simulations. The obtained results help in getting a better insight on the need of computational power, and possible numerical errors using compressible or incompressible solvers in future simulations. In a second step, systems without vapour explosions were simulated and compared to experimental results with mercury and aluminum. INTRODUCTION Humanity started using metals for tools around the Chalcolitic (~7400 cal BC), when copper was melted in small furnaces (Radivojevic, Rehren, Farid, Pernicka, & Camurcouglu, 2017). Nowadays, metallurgy has grown into a major industry and it has become impossible to imagine society without metals. In the pyrometallurgical industry, coolants (low temperature liquids, for example water) and pyrometallurgical phases (high temperature liquids, such as slags, mattes and alloys) are typically present in close proximity of each other. The interaction between these two phases can have catastrophic consequences (Tveit et al., 2008; Ferguson & Zsamboky, 2017). A vapour explosion may occur as the consequence of the rapid evaporation and expansion of the coolant. Whereas the volume of a gas increases linearly with the temperature (approximately a factor four by heating from 100°C to 1300°C), a simple calculation of the ratio of the two specific volumes shows that evaporation causes the volume of water to increase by a factor of 1700 at 100°C and ambient pressure (Table 1 and equation (1)), a number that was also found in literature (George, Nexhip, George-Kennedy, Foster, & Walton, 2006). The volume change occurs so fast that it resembles an explosion, hence the name vapour explosion. Such an explosion at industrial scale can cause economical losses, bodily injuries or even fatalities.

Jan 1, 2019

By R. E. Whitehead

"The earliest gold-mining operations in Ontario included the Cordova, Deloro, and Sophia mines north of Lake Ontario (see for example, Miller and Knight, 1914). The Cordova deposit, worked intermittently between 1891 and 1940, is reported to have yielded 22 774 oz of gold from 127 670 tons of ore averaging 0.19 oz/ton Au (Gordon et al., 1979). The property remained inactive for many years. In 1988, Gunnar Gold Inc. and Mill City Gold Inc. conducted a drilling program along the main Cordova vein. The present study is based on core from three drill holes through the Cordova gabbro (Fig. 1) and the carbonate alteration zones enveloping the quartz-carbonate veins. The relatively narrow width of the alteration zone and the availability of continuous sections of core provided an opportunity to conduct a compact mineralogical-chemical study of carbonate alteration and its effect on the redistribution of rare earth elements (REEs). Although the Cordova deposit is not of great economic importance, this study has revealed a number of interesting features which are interpreted as resulting from processes that may be applicable to gold-bearing quartz vein deposits elsewhere.The Cordova gabbro is layered in places, varying from fine-to coarse-grained and in color from light gray (feldspathic) to dark gray-green (amphibolitic). However, layering within the section of the gabbro considered here and which hosts the Cordova gold deposit is mainly textural rather than compositional. Samples of unaltered gabbro selected for analyses were medium- to coarse-grained; amphibolitic and anorthositic phases were avoided as being less representative of the general chemical composition of the gabbro.The Cordova intrusion has undergone regional metamorphism and consists dominantly of actinolite and saussuritized plagioclase with smaller amounts of granular clinozoisite and flaky chlorite; minor quartz, ilmenite, titanite, apatite, and calcite are typically present. Some actinolite grains have irregular rims of pleochroic green hornblende that is optically continuous with the actinolite. Both chlorite and clinozoisite occur in two modes. Chlorite occurs as an alteration product of actinolite and as separate grains in the groundmass. Clinozoisite and albite occur together as regional metamorphic alteration products of original plagioclase crystals and as discrete grains in the matrix.The main gold-bearing quartz-carbonate occurrence occupies an easterly trending, steeply southward-dipping carbonatized shear zone up to 15 m wide and 700 m long. The gold occurs principally in irregular lenses and veins of quartz-carbonate up to a foot thick occupying the lower part of the schistose shear zone within the gabbro. This zone consists of chlorite, biotite, and carbonate and is flanked on both sides by chlorite-carbonate schist lacking biotite. The chlorite-carbonate schist in turn grades into regionally metamorphosed actinolite-bearing undeformed gabbro.The dominant sulfide within the quartz-carbonate lenses and in the surrounding schist is pyrite which occurs mainly as small cubes (1 mm to 2 mm) generally making up less than 10% of the rock. Rare blebs of chalcopyrite are present. Magnetite is common throughout the schist."

Jan 1, 2001

By Ronald C. Schimmel

In 2006, the Corus IJmuiden pellet plant produced approximately 4.6 mln tonnes of pellets. Corus IJmuiden is about to increase its pig iron production to 6.4 mln tonne HM per annum. The burden of the Corus IJmuiden blast furnaces consists of approximately 50% high basicity sinter and 50% acid pellets, both produced in-house. To enable an increased iron production, the capacity of the pellet plant needs to be raised to 5.0 mln tonne per annum. The capacity is increased by modifications to the plant layout, which were implemented during the 2006 cold maintenance stop. In addition, the composition of the ore blends is optimised to gain productivity.

May 1, 2007

By W. A. Dixon Edwards

Gravel deposi ts in the Edmonton region are unique in their diversity in origin and age. The deposits were described first around the turn of the century (Dawson and McConnell 1896) . Among the many more recent in vestigations are works by Rutherford (1936), Shelley and Associates Limited ( 1977) and the City of Edmonton (1978) .

Jan 1, 1984

By K. G. Markkola

Since 2005, Compafifa Contractual Minera Candelaria (CCMC) has defined various strategies which aim to optimize the usage of the available energy in each of the SAG grinding circuit modules (SABC-A configuration). For this purpose, the use of larger size balls along with operating with an optimum balls/load ratio has been implemented. Additionally, in the ball mills, the amount of balls in relation to the equipment's usable diameter has been optimized. In the pebble crushing circuit, the percentage of material passing 12 mm (112 in) product has been increased by 15% by: (1) modifying the crusher mantle profile, (2) implementing a strategy for maximizing the power in each crusher, (3) using continuous improvement tools (Lean - Six Sigma), (4) redesigning SAG mills discharge grates, and (5) changing discharge grates in order to control the crusher feed size distribution profile. All these activities have improved plant throughput by 1,000 t/d with no significant capital investment. As part of the energy consumption optimization study, we have considered determining the optimum operational rate of each SAG mill, in relation to the mill liner life and also the improving the control strategy in conventional grinding.

Jan 1, 2007

By J. M. Ortiz, J. Haas, W. Kracht, G. Pamparana

This work explores the effect of ore hardness variability on the design of a solar photovoltaic system with battery storage and grid backup, to operate a semi-autogenous grinding mill (SAG). First, a case of two synthetic ore populations was studied, without any consideration of spatial distribution. The mean and variance of the ore hardness (measured in specific energy consumption) of both populations were subjected to a sensitivity analysis. The operation was evaluated with one and two stockpiles. The latter allows classifying according to ore hardness to adapt the SAG energy consumption to the solar cycle. The results show that using two stockpiles allows achieving a larger autonomy (i.e., fewer energy imports) at lower total costs, especially when the difference of mean hardness between the two populations is large. The difference in variance (between the two populations) has a smaller impact on the design recommendations. Second, a case study was performed considering the spatial distribution of geometallurgical units. Two cases were considered: (a) brownfield, when there is historical information of the actual variability of the ore hardness; and (b) greenfield, when the system design relies mainly on geometallurgical modeling. Brownfield and greenfield planning result in similar sizing recommendations of the solar power plant if precise drill cores are available. In this case, geometallurgical modeling is an effective tool for forecasting the energy demand necessary for designing the power plant. INTRODUCTION Solar energy can help make mining more sustainable (Moreno-Leiva et al., 2017). With falling battery costs, an autonomous solar supply is soon to become an economical alternative in many parts of the world, even in the presence of a larger power grid (Child et al., 2017). Although this, places with high solar radiation such as the Atacama Desert in Chile, nowadays show a large potential of incorporating solar energy as a supply of energy. Many of the Chilean copper mines are in this zone making it interesting to study their compatibility and potential of integrating this renewable source to their operation. The power demand in a copper mineral processing plant is determined by the main power loads in grinding and flotation, with grinding typically the largest power consumer, especially the semi-autogenous grinding (SAG) mills (Wei and Craig, 2009). In Chile, it corresponds on average the 50% of the electrical energy consumption (COCHILCO, 2013). Solar energy production is determined by the irradiance perceived into the solar photovoltaic (PV) panels (which varies through the geographic location) and several other climatic parameters such as the current season, humidity, temperature, altitude, and others (Molina et al., 2017). Also, solar energy is only generated during the sun hours, getting to a maximum generation at a certain peak hour during midday, and finally dropping to zero during the night. This shows a cyclic parabolic profile as shown in Figure 1. Due to the SAG mill operated continuously, the power supply always must be available. During the night, to continue supplying the energy, it is necessary to complement the solar power generation with a battery energy storage system (BESS), which will act as a power backup and a buffer. For the optimal sizing of this PV- BESS system, information of the demand profile is needed (Pamparana et al., 2017). In the case of the SAG mill operation, the resulting demand relates to the ore-hardness for a specific throughput and grind size (Morrell, 2004). Therefore, for a given throughput and target grind size, a harder ore would require more power, and variable hardness results in more variable demand and a subsequent need for larger energy storage (Bueno et al., 2015). Due to the ore-hardness variability and the operation of the mill, the power demand profile in inherently variable.

Jan 1, 2019