Search Documents

By G. R. Davidge

"Falconbridge Mine has a history of significant microseismic activity dating back to 1955. Since mid-1981, a microseismic monitoring system has been operating in the area around the No .9 Shaft hoist room located 25 m from the are zone at a depth of 1200m. Several mine wide faults dissect this area and have been shown to be microseismic-active due to mining. The microseismic monitor has been interfaced with a small dedicated personal computer and a communications device to perform routine data evaluation and to produce graphical output. The programs are described and selected result s from the monitoring program are presented.IntroductionFalconbridge Mine is located on the southeast rim of the Sudbury Basin. The nickel-copper sulphide ore zone is essentially a tabular orebody striking approximately east-west and dipping at 80 degrees north near surface and rolling to 75 degrees to 80 degree s south by the 1000 level. (Mine level number s represent the approximate depth in feet below ground surface .) This dip is maintained down to the 6000 level. The north wall is comprised of jointed norite and a faulted contact up to 1 m thick exists between the ore zone and the norite. The south wall rock is a greenstone with highly siliceous lenses and often has a faulted contact with the ore zone. No less than five mine wide faults exist, as shown in Fig. I.Mining ha s been carried out from virtually the bedrock contact to depths of 1830 m although the majority of current activity is between 900 and 1500 m below surface. A winze provides access below the 4025 level and the cage hoist room is located on the 3850 level in the north wall 25 m from the contact. Because of concern for the stability of this hoist room, there has been no mining activity within 60 m of the hoist room and by 1980 this block of ore was one of the major blocks of high-grade ore remaining in the mine . Mining of this block was originally scheduled for very late in the decade.Prior to a six-month shutdown in 1982, this mine produced approximately 450,000 tonnes of ore annually, mainly by cut and- fill techniques. Following the shutdown, annual production has been reduced to approximately 200,000 tonnes and production is now mainly by undercut and fill techniques .Mining-induced seismicity has occurred at Falconbridge Mine since at least 1955 and reviews of the microseismic problems for the periods from 1965 - 1970 and from 1971 to 1979 were made by Singh (1971) and Vongpaisal et al. (1980), respectively. The need for instrumentation was addressed by these authors. Following several large events during the spring of 1980, a decision was made to investigate existing microseismic monitors and to apply micro seismic monitoring techniques in Falconbridge Mine. Application of microseismic monitoring to Falconbridge Mine was to concentrate on the No . 9 Shaft hoist room area of the mine, particularly around the 4025 level where a large mechanized cut-and- fill stope was approaching this level. By mid - 1981, the microseismic monitor was fully installed and with in a year , a short-period seismograph and a personal computer had been added to the system."

Jan 1, 1984

By P. R. A. Andrews

"Talc ore from Bakertalc, High water, Quebec analyzing about 60% talc, previously dry ground to about 95% minus 53 µm was beneficiated in an 11.4 kg/ h pilot-plant flotation circuit. A concentrate of 95.9% talc (necessary for paper-grade) was obtained at a recovery at 75.3% by employing 53 g/t of Dowfroth 250 collector at pH 9.2; further cleaning increased the grade to 97.2% talc at a recovery of 57.5%.Flotation of fresh ground 60% minus 44 µm ore at a feed rate of 18.6 kg/ h produced a grade of 96.4% talc with a recovery of 78.2%, using Aerofroth 70 collector a six carbon-branch chain alcohol, at pH 9.2.The similarity in the concentrate grade and recovery between pre-ground and fresh-ground ore indicated that it was not neces¬sary to grind to 95% minus 53/2m to achieve comparable selectivity. A grind of 60% minus 44 pm corresponds to 100% minus 300 µm.Flotation retention times obtained with fresh ground ore indicate 33 min. for combined rougher/scavenger, and 15 min. each for the first and second cleaners.Talc-magnesite flotation separation is explained in terms of physico-chemical forces, with reference to surface charge and adsorption mechanisms."

Jan 1, 1989

By M. J. Brodie

"The decision to proceed with mine decommissioning, generally involves a number of complex and independent factors. These factors, including potential for re-opening, legal requirements, contingent liability, asset depreciation, due diligence, and public relations are discussed in the context of the financial implications on a net-present- value basis. It is concluded that the decision to delay mine decommissioning is commonly not in the best financial interests of the mine operator. Some measures to reduce decommissioning costs and expedite the process are presented.IntroductionThe primary audience for this paper is mining executives, although it should be of interest to all professionals involved in the planning and carrying out of mine decommissioning. Historically, mines were abandoned, not decommissioned. Then, as decommissioning became required, it was assumed that salvage revenue would pay for decommissioning. During the I980s, it became apparent that mine decommissioning costs would exceed salvage revenue for nearly all sites, and that a substantial net cost for decommissioning would be realized for some sites. Throughout this period, the approach to decommissioning has evolved through the sequential addition of measures to meet the increasing regulatory burden. This has resulted in a process in which the elements of decommissioning may not be optimized with respect to each other for the most favourable net present value to the corporation. Additional considerations which are not specific to mine decommissioning, such as environmental policy, due diligence and public relations, may now come to bear on the decision-making process.This paper addresses the issue of mine decommissioning as a three-step process. The first step involves identification and evaluation of all of the issues that relate to mine closure, the most importantof which is the potential for re-opening of a mine. Assuming that it is decided that a mine is unlikely to re-open, the second step is to determine when to carry out the decommissioning work. This aspect is examined through a net present value (NPV) approach. Finally, details regarding who does the work and how the various tasks are divided up must be resolved.Every mine is a unique concentration of minerals at some specific location, hence the development, operation and closure of a given mine must be regarded as a special case. Superimposed on the site-specific considerations are the size, history and financial status of the associated corporation."

Jan 1, 1995

By R. P. Taylor

"This paper covers the development of the property to its present production level of20,000 tonnes per day from the Valley Mine. It will also review the analysis of various case studies for the expansion of the project to its full potential, and discuss the impact of the recent structural change in the copper market on the development of a large low-grade deposit such as Valley.IntroductionIn 1964 Cominco participated, along with a number of other companies and individuals, in the formation of Valley Copper Mines Ltd. This company was formed in order to facilitate exploration on a large number of mineral claims held by these parties in British Columbia's Highland Valley, approximately 400 km northeast of Vancouver (Fig. I). Cominco 's ownership of Valley Copper was gradually increased over the years bot h through shares gained for exploration expenditures and through shares purchased on the open market. By the mid- 1970sCominco' s interest in Valley Copper exceeded 80%.ExplorationExploration from 1964 to 1969 led to the discovery of a massive porphyry copper depo sit now known as the Valley orebody. A claim boundary divided the deposit with 80% of it on Valley Copper claims and 20070 on claims held by Bethlehem Copper which was already mining adjacent copper orebodies. During the period when the Valley ore body was discovered, exploration by other companies resulted in the discovery of the large Lornex and Highrnont deposits nearby. The stage was now set for the Highland Valley to become an important copper-producing area (Fig. 2)."

Jan 1, 1986

By H. Utsunomiya, Mehdi Sanjari, Abu Kabir, Steve Yue, Jing Su, L. Kestens, In-ho Jung

The microstructure and texture evolution of low temperature rolled AZ31 magnesium alloy during annealing were investigated. The specimens were rolled at the temperature of 100? at a high rolling speed of 1000m/min with a reduction of 30% in one pass. Annealing was conducted at various temperatures ranging from 200? to 500? for different time. To study the effect of fast speed rolling, the same annealing procedures have been applied for the specimens rolled at a significantly lower speed of 15m/min. The microstructure was characterized by optical microscopy and scanning electron microscopy, while the texture was analyzed by X-ray diffraction analysis and electron backscattered diffraction analysis. Texture weakening occurred during annealing at both fast and slow rolling speeds. However, at the same annealing condition, fast rolled specimens always had weaker intensity of basal texture than slow rolled ones.

Jan 1, 2014

By L. D. Smith

"Those who submit competing proposals for projects seek to present senior management with complete and fully supported material that will not fail under questioning. Hopefully, misleading notions and omissions will have been minimized and there will have been testing of the assumptions regarding the economic, social and political environments.A capital project evaluation team can do management and itself a service by including a sound approach to the impact of inflation (and its twin problem, interest) on a project and a great disservice with an inappropriate approach to inflation.InflationHandled deftly, inflation can alter a project evaluation to show almost any result the handler desires. It must be a constant source of frustration for design people and cost estimators to spend weeks perfecting the technical aspects of a project in order to minimize costs, only to have all of their efforts set awash in a sea of financial and economic assumptions that submerge all of the detail. In all of this, inflation is perhaps the largest offender, with inflation criteria often being brought to bear at the last minute, almost as an afterthought. Perhaps this tardiness reflects the difficulty of the subject and the belief that senior management will take its own approach to the problems of inflation. Such a belief is unfair to senior management, for it is entitled to not being misled by omission. It is entitled to the full use of the skills of the evaluating team, including reasonable assumptions of the impact of inflation.Working in a consulting context, one has the opportunity to participate in the evaluation of a large number of projects."

Jan 1, 1990

By Stephen G. Hardcastle, Michel G. Grenier

"Safety and health issues are and have been in the last decade a very high priority item with all parties involved in the Canadian mining industry. As a result of this high level of concern for workers' safety and health, Canadian mines are at the leading edge of environmental control technology. For the most part, the occurrence of pollutants in mines is unavoidable. Dust from mining operations, airborne radiation, gases and heat from the strata as well as gases and particulate from diesel engine emissions will undoubtedly be found to some level in most Canadian mines. A lot of work remains to be done, however, in order to bring all Canadian mines at the same level of proficiency when it comes to safety and health. Also, more work is needed in order to maintain our status as world leaders in this field.CANMET's Mining Research Laboratories (MRL) in Elliot Lake and Bells Corners, Ontario, with the cooperation of the mining industry, have contributed to improving environmental conditions in underground and surface mining and milling operations. The extent of collaboration and efforts vary widely from long-term, multi-million dollar projects between several interested parties to smaller projects involving one laboratory and a single mining operation. This paper gives examples of such collaborative efforts and potential future directions as they apply to: mine ventilation analysis using tracer gas techniques, optimization of mine ventilation network efficiency using real-time monitoring and controlled recirculation (heat saving), respirable dust and radiation sampling and control techniques, diesel emission control using regenerative ceramic filters and, finally, the control of sulphide dust explosions and resulting sulphur dioxide production."

Jan 1, 1990

By D. Pérez Escobar

Multiphase steels are quite sensitive to hydrogen embrittlement. Laboratory tests to evaluate this often use electrochemical, charging to introduce hydrogen into the sample, but damage purely caused by hydrogen charging has to be avoided. A ferrite-bainite steel, was charged using various conditions to identify when surface blisters occurred. Samples were also checked for internal, damage by electron microscopy. This study was repeated for three other multiphase steels and pure iron. An HSLA steel, was found to be more resistant whereas pure iron was quite susceptible to internal, hydrogen damage. For al, industrial, steels, cracks concentrated in the middle of the sample were attributed to inclusions and segregations, inherent to production.

Jan 1, 2010

By Alan R. Holt

"This paper provides an overview of the use of uranium and coal in Ontario Hydro's generation program. The dynamics of available supply sources including mining and transportation infrastructures and regional considerations are described. Included is a discussion of needed procurement strategies, both in place and planned, to meet fluctuating fuel requirements while ensuring adequate supply security and cost effectiveness. IntroductionDuring the first half of this century, Ontario Hydro or the Hydro Electric Power Commission of Ontario, as it was then known substantially supplied all of the province's electricity needs from a large number of hydraulic generating stations. Although hydraulic power still provides a very significant part of Ontario energy requirements, this paper will concentrate on the role of uranium and coal in their generation program. To provide a perspective on the importance of these two fuels, Figure I shows the approximate value of each for the past few years in relation to Hydro's total operating costs. The trend toward increasing nuclear output and a corresponding decline in coal use is also clearly illustrated.Figure 2 shows the currently installed capacity of their three main energy sources, hydraulic, nuclear and coal and the 1986 production totals for each, followed by Table I which compares the average operating or running cost on the basis of dollars per megawatt hour for each type of plant. It demonstrates dramatically why Ontario Hydro base load s its hydraulic and nuclear plants, and why coal has become the swing fuel on the system. Although they have a 1200 megawatt plant in Toronto with natural gas-burning capability, and a 2000 megawatt oil-fired station near Kingston, both are presently mothballed and have not been considered in this paper.This paper starts with a user's perspective of the nuclear fuel supply situation which will be discussed in relation to the usual considerations of security, flexibility and cost."

Jan 1, 1988

By H. R. Manouchehri, A. Weh

"High voltage electric pulse comminution (SELFRAG) relies on inducing electrical breakdown that occurs when the resistivity of a dielectric is insufficient to completely block all transfer of electricity while the conductivity is not high enough to fully accommodate the flow of electricity without considerable changes to the crystal lattice. The technology is based on introducing the electrical discharges into solids immersed in water and placed between two electrodes. The technology has received significant attention since investigations have revealed the potential for fully fragmenting particles or pre-weakening rocks in order to reduce the energy consumption in comminution practices, improve liberation and potentially increase the recovery in mineral processing. Mineralogical analysis of samples showed possible liberation at coarser sizes by high voltage breakage in comparison with conventional mechanical comminution.This study explored the potential of implementing SELFRAG to treat the Sandvik’s Mittersill mine tungsten ore (scheelite) for recovery improvement. Accordingly, standard SELFRAG tests were conducted on four samples from the tungsten process plant to evaluate the energy-breakage relation and potential to liberate the value minerals at coarser size fraction for recovery improvement. The size reduction of the ore after processing with SELFRAG revealed that size deportment occurs at 0.4, 0.2, and 0.1 mm, which indicated potential liberation of gangue and target minerals at respective sizes. In comparison with conventional milling, the difference is the deportment of values into 0.4 mm sizes, which was, to some extent, confirmed by SEM liberation analysis. However, more tests are needed to proof the concept. The study has indicated that, despite consuming more energy in comparison with conventional mechanical comminution, there are promising prospects in liberating the values at coarser fraction and improve recovery by making use of SELFRAG. The energy consumption can be reduced through customized generator and equipment setup, which must be further investigated."

Jan 1, 2016

By J. P. Harrison, K. Gao

It is well known that in situ stress measurements at a given site will generally display significant variability. However, it appears that a robust analysis of such measurements – i.e., one that is faithful to the tensorial nature of the data – is not available. Despite the fact that stress is a tensor, stress magnitude and orientation have long been analyzed separately using classical statistics. In earlier work we demonstrated the applicability of tensor statistics to the analysis of stress variability. Here, we investigate further the difference between tensor and classical statistics with respect to the stress tensor correlation matrix. Our analysis commences with the selection of a series of valid correlation matrices. Then, assuming that standardized tensor components follow the multivariate standard normal distribution, these correlation matrices are used to generate marginal probability distributions of the eigen-parameters (i.e., principal stress magnitude and rotation angle). From these, random stress tensors are generated, their eigenparameters determined, and the probability density distributions of these obtained using both classical and tensor statistics. Our results indicate that, for all correlation matrices, both methods give practically identical distributions for principal stress magnitude. However, the discrepancy between the two methods with regard to probability density distribution of rotation angle is highly dependent on stress component correlation. This discrepancy is usefully quantified in terms of the integral, with respect to orientation, of the difference between the two probability density distributions. This parameter, which we term Area Difference, is closely linked to the magnitude of the correlation matrix determinant, which itself is related to the normal stress correlation coefficient (i.e., ?x ,?y ??). Assuming that Area Difference should not exceed 0.1, we identify the critical determinant for any particular value of normal stress component correlation coefficient. Thus, using published in situ stress data and the obtained critical determinants, we show that for a specific normal stress component coefficient, when the correlation matrix determinant is less than its critical determinant, the more precise tensor statistics should be used to calculate the distribution of rotation angle. These results demonstrate that the customary analysis of stress measurement data may lead to erroneous results, and that tensor statistics appears to be preferred approach.

Jan 1, 2015

By R. P. Mahant

"Extensive pilot plant investigations were conducted both on partial roasting an d electric furnace smelting from September 1973 to August 1975.The objectives of the pilot plant investigations were:(I ) to confirm the application of available process technology to treatment of Falconbridge concentrate.(2) to examine partial roasting variables.(3) to investigate electric furnace smelting of roaster calcines .(4) to develop process design and operating parameters for a commercial plant.This part of the paper will cover the following topics:Partial Roasting InvestigationsPilot Electric Furnace InvestigationsPartial Roasting InvestigationsThe specific objectives were to:1. establish process variables for maximum oxygen efficiency and bed fluidi ation.2. determine the product distribution between the roaster and the various gas cleaning stages.3. produce a mass and thermal balance."

Jan 1, 1984

By S. S. Rahman, A. Gholami, M. A. Aghighi

"This paper provides a foundation for studying the growth of fractures in presence of other discontinuities and different anisotropies of low permeable hydrocarbon formations and helps to improve the design strategies for multistage fracturing.The multistage fracturing technology has recently been used to exploit low permeable hydrocarbon reservoirs. However, the mechanism of hydraulic fractures interaction and the impact of local heterogeneities on ultimate trajectory of the growing hydraulic fractures are not yet understood in depth. A fully coupled poroelastic Finite Element based model is developed to investigate the mixed mode propagation behaviour of growing hydraulic fractures. This model takes advantage of an explicit representation of the fracture which enables us to take the effects of rock and fluid related parameters into account. Moreover, impact of fracture geometry and leak-off phenomenon is investigated. The refined mesh around the crack provides the added advantage of more detailed stress distribution, pore pressure change and back stress in the vicinity of the fracture and in particular at the fracture tip. The potential deviation propensity of the fractures is evaluated based on the fundamental rule that fractures propagate perpendicular to the direction of the minimum horizontal stress.This study shows that pressurization of transverse hydraulic fractures results in the reorientation of local principal stresses, particularly in vicinity of fracture tips. Variation of flow patterns clearly influences the evolution of shear stress around the fracture tips which will potentially lead to mixed-mode I and II fracturing and consequently, fracture deviation. The presence of local heterogeneities such as preexisting fissures and/or fractures is a main source of such pore pressure induced stress redistribution and reorientation and potential deviation of hydraulic fractures.Most existing models ignore or simplify the effect of pore pressure/stress coupling as well as the fracture geometry and fluid flow within the fracture. Also, the fluid leak-off from the hydraulic fracture into the formation, which is a controlling factor in fracture growth, is often considered using analytical models. Taking advantage of a fully coupled porelastic model along with an explicitly discretized fracture, this study provides a more realistic insight into the complex fracture propagation processes of multistage fracturing operations particularly in presence of reservoir geo-mechanical complexities."

Jan 1, 2015

By M. A. Sobhi, L. Li

With the continuous reduction of mineral resources at shallow depth, more and more mines have to go deeper beneath the earth's surface to reach the ore zones. This increase in mine depth leads to a natural stress increase, which also raises the stresses around mine openings. This may result in ground instability, including the risk of rock bursts or exceedingly large opening closure. Stope backfilling is a well known solution to improve the ground stability condition. It also has the advantage of reducing the mining wastes disposed on surface, thus helping to reduce the environment impact from the industry. However, most available solutions for backfill design were developed for an isolated stope without taking into account the influence of mine depth, except for a few numerical analyses performed recently by Falaknaz and coworkers for the case of multiple backfilled stopes laying in the same level. In this paper, a numerical study is carried out to evaluate the stresses in backfilled stopes overlying a sill mat. The mine depth and the excavation of the underlying stope below the sill mat are both taken into consideration. Compared to the case of a single isolated backfilled stope, the obtained numerical results show that the stress magnitudes in the overlying backfill are considerably increased due to the excavation of the underlying stope. In general, the stresses increase with mine depth and backfill stiffness, but decrease with an increase in the surrounding rock mass stiffness. These results indicate that the barricade and sill mat backfill design should take into account the excavation of the underlying stope and the mine depth.

Jan 1, 2015

By Frédéric Flament, Mary Goldman, Gille Barbery

"Pilot plant testwork on autogenous and semi-autogenous grinding was conducted at the Centre des Recherches Minérales du Québec (CRM) to investigate the effect of ball addition, solids concentration in the feed, specific energy consumption and feed size distribution.A mathematical model that incorporates breakage and surface mechanisms of loss of mass was developed to predict load size distribution of autogenous and semi-autogeneous mills. An empirical model was used to predict product size distribution of autogenous and semi-autogeneous mills.IntroductionAutogenous (AG) and semi-autogenous (SAG) grinding circuits offer potential capital and operating cost savings when compared with conventional grinding. Empirical relationships have been developed to calculate specific power consumption for SAG mills using pilot plant test results (Mular et al., 1989; Barrett and Allan, 1986). Empirical models can be obtained from plant practice data but are applicable only to the particular ore and set of operating conditions used in the model. Grinding mechanisms have to be taken into account in order to develop a model that can be applied to different ores and mills.In AG and SAG, the ore itself acts as grinding media, with the finer sizes being crushed by the coarser ones. Surface mechanisms of loss of mass, in which the inner core of the particle remains intact, also take place. In SAG milling, the effect of balls also has to be taken into account. The role of each one of these mechanisms changes with particle size and the model has to account for such changes."

Jan 1, 1991

By I. A. Cameron, F. Ham, R. Sriram

"Planned increases in electric furnace productivity and higher matte temperatures needed for the Sudbury Smelter's S02 Abatement Plan, require an improved matte tap hole. Since startup in 1978, the matte tap holes have been incrementally improved by the addition of copper cooling blocks around the refractory tap blocks. These improvements provided a tap block life of about 100 taps per campaign.In July 1993, a prototype matte taphole was installed in Number 2 Electric Furnace to develop the technology to increase tap hole service life. The design was based on a heat transfer model of the tapping process to determine candidate refractory materials and cooler arrangements. The prototype tap hole features increased copper cooling, high conductivity refractories and extensive instrumentation. Eight trial campaigns are reviewed outlining the performance of silicon carbide and graphite refractories and typical heat loads during tapping.IntroductionFalconbridge Limited operates two 36 MYA, 6 electrode submerged arc electric furnaces in Falconbridge, Ontario. The furnaces, commissioned in 1978, smelt a partially roasted nickel-copper calcine, to produce matte for converting and slag for discard. Additional details of the smelter are available in the literature(1-4).Each furnace was equipped with two matte tap holes located in the furnace end wall. Early in the campaign, matte tap holes were identified as a weak area in the furnace which could be improved. From 1981 to 1987, incremental improvements were made to the design by the addition of water cooled copper blocks. In 1993, a prototype matte tap hole was designed and installed in Number 2 electric furnace to develop the technology to increase tap hole service life. Improved service life is required to meet planned increases in electric fWl1ace productivity and the higher matte temperature needed for the smelter's S02 Abatement Plan.This paper reviews matte tap hole development since 1978; outlines the prototype matte tap hole design, refractory selection and installation; and details the performance of the prototype tap hole during the first eight campaigns."

Jan 1, 1995

By W. G. Brown

"Review of prototype testing of two types of three-phase, argon stabilized reactor/furnace indicates specialized advantages for both, as compared with existing metallurgical furnace technology. They are: the direct-arc, plasma-torch furnace (Knipp); and the indirect, plasma extended-arc reactor (PEAR), developed at the University of Toronto.IntroductionA unique type of three-phase AC, plasma extended-arc reactor, (PEAR), shown in Figure la with gravity feed, has been undergoing development at the University of Toronto, during the past fifteen years: argon gas, introduced axially through drilled-holes in ordinary graphite electrodes, increases the length of indirect arcing and improves electrical stability while decreasing electrode consumption as compared with the performance of AC electric arc furnaces (EAF 's). Meanwhile and independently, a three-phase, transferred arc plasma furnace (Fig. 1b) has been developed by the Krupp Research Institute in Germany, using argon-stabilized, water- cooled plasma-torches with thoriated tungsten electrodes.Accordingly, the two types of furnace are similar as to both three phase and stabilized operation, but otherwise they differ in several respects, ranging from indirect versus direct-arcing to principal intended application and current state of practical development. Between them they raise questions: (I) of their present or fore seeable economics in comparison with existing processes they are intended to replace , (see Heinke and Neuschutz, 1986, for a review of the merit s of AC and DC plasma-torch furnaces); and (2) of the state of development and accessibility of their plasma theory-in-common."

Jan 1, 1991

By A. P. Annan, C. Vaughan, J. L. Davis

"The increase in the price of gold in the last decade has led to a significant increase in placer gold exploration around the world. Placer deposits occur in depressions along ancient river and stream channels. In many instances these channels have been covered with materials from subsequent erosion or glacial activity. Use of high resolution geophysical techniques to map the bedrock and soil strata can improve the probability of finding the placer deposits. The buried bedrock surface is often the factor controlling deposition. Ground probing radar (GPR) and seismic sounding are complementary high resolution techniques which can be used to map bedrock topography and soil stratigraphy. Current radar instrumentation operates best in coarse grained soils. Penetration depths of up to 30 m have been attained, and stratigraphic horizons have been mapped with spatial resolutions of better than 0.5 m. Although its spatial resolution is considerably lower than radar, seismic refraction achieves superior penetration in electrically conductive environments such as clay and silt soils. The seismic refraction method thus proves to be complementary to the radar method. The seismic reflection technique is analogous to the radar method. Current seismic instrumentation and energy sources however, provide limited spatial resolution and do not permit the use of seismic reflection for reflecting horizons lying at depths of less than 20 m to 30 m.This paper discusses the use of both radar and seismic methods for placer exploration. The radar and seismic techniques, the field methods, equipment, and data displays are presented. Field examples illustrate the high resolution mapping capabilities of the techniques. The radar data agree very well with the borehole data, and in fact they sometimes detect subtle soil strata variations associated with changes of permeability that were not initially observed in the borehole logging. The radar method can give a continuous profile of water table and bedrock in sandy soils. Seismic soundings are necessary to differentiate between the bedrock and water table reflections observed by the radar."

Jan 1, 1987

By R. L. Armstrong, C. I. Godwin, V. M. Kruan

"The Scheelite Dome tungsten-bearing skarn property, central Yukon Territory, is in metasediments in contact with a quartz monzonite intrusion. Contact metamorphism to biotite-muscovite- andalusite hornfels and calc-silicate hornfels is superimposed on low-grade regionally metamorphosed rocks represented by quartz-mica pelitic schist and muscovite-biotite pelitic schist.Metasediments are likely Precambrian in age, even though Rb-Sr whole-rock analyses indicate an early Paleozoic age (511±41 Ma); this apparently too young radiometric age is due to partial loss of radiogenic strontium during regional metamorphism. The minimum age of the quartz monzonite intrusion is Cretaceous at 90.4±2.6 Ma (K-Ar on biotite) and its initial 87Sr/86Sr ratio is 0.7121. The high initial ratio of the intrusion is due to the addition of radiogenic strontium from the metasedimentary country rocks and perhaps an underlying older basement.Scheelite-pyrrhotite-chalcopyrite mineralization occurs in diopside-zoisite skarn pods within the calc-silicate hornfels near the quartz monzonite intrusion. The source for lithophile tungsten is probably the same as for the granitic magma, namely Precambrian sialic basement.IntroductionThe Scheelite Dome tungsten skarn property is within the Mc-Questen map-area (NTS: 115P/16),28 km northwest of Mayo, Y.T., at latitude 63°47' north and longitude 136°15' west. The property can be reached by helicopter or by four-wheel- drive vehicle from Mayo.This paper summarizes the geology of the Scheelite Dome property, which has been described in a general way by Little (1959) and Cathro (1969). Geological mapping and sampling were done by the first author (nee Steffler) during June 1979. Field work was supplemented with detailed work at the Department of Geological Sciences of The University of British Columbia during 1979 and 1980 (Steffler, 1980). Whole-rock chemical analyses were done by Cominco Ltd."

Jan 1, 1982

By Carlos Palacios M., Brian K. Townley

"Abstract - The mainland Aysén region of Chilean Patagonia (44°15' - 47°30'S) is a representative segment of the South American active continental margin, distinct with respect to northern and central Chile. Mineralization consists mainly of polymetallic deposits, with important Zn-Pb mines and more recently discovered Au-Ag deposits, unlike the central Andes, which are dominated by Cu mineralization. On a regional scale, rocks may be grouped in four main map units: 1) the Paleozoic metamorphic basement; 2) upper Jurassic-Cretaceous calc-alkaline volcanic and marine sedimentary rocks; 3) the Patagonian batholith, and 4) upper Cretaceous to Miocene basalts and marine and continental sedimentary rocks. The upper Jurassic-Cretaceous rocks and the Patagonian batholith formed in a volcanic arc and back-arc setting superimposed on the Paleozoic metamorphic basement.Based on geographic location and geologic and tectonic setting, ore deposits in this region are assigned to three groups, from south to north: El Faldeo, Fachinal, and El Toqui. The El Faldeo group (south of 47°05'S) includes upper Jurassic Zn-Pb skarn and associated polymetallic massive sulfide vein deposits locally overprinted by Au-rich epithermal mineralization, hosted by volcanic and sedimentary rocks and/or by rocks of the metamorphic basement. The Fachinal group (46°05' - 47°05'S) consists of volcanic-hosted lower Cretaceous Au-Ag epithermal deposits, except for the Mina Silva and Manto Rosillo deposits, which are metamorphic basement-hosted Zn-Pb skarns. The El Toqui group (44°30' - 46°05'S) comprises lower Cretaceous Au-rich Zn-Pb skarns and associated polymetallic veins, as well as Au-Ag-rich epithermal deposits, hosted by volcanic, intrusive, and marine sedimentary rocks. Galena lead isotopic signatures for each deposit group indicate a decreasingly radiogenic trend from south to north, suggesting different lead sources or differences among underlying crust. Three metallogenic provinces and two metallogenic epochs are proposed for the Aysén region: the El Faldeo metallogenic province of Late Jurassic age; and the Fachinal and El Toqui provinces of Early Cretaceous age. Résumé - La partie continentale de la région d’Aysen (Patagonie chilienne, 44°15' - 47°30'S), est unsegment représentatif de la marge continentale active d’Amérique du sud, différent des segments du nordet du centre du Chili. La minéralisation, qui consiste essentiellement en des dépôts polymétalliques, avec d’importantes mines de Pb-Zn, et des dépôts d’Au-Ag récemment découverts, différe de celle des Andes centrales où domine la minéralisation cuprifère. A l’échelle régionale, les roches peuvent être regroupées en quatre unités cartographiques principales : 1) le socle métamorphique paléozoïque, 2) les roches volcaniques calco-alcalines et les sédiments marins du Jurassique supérieur-Crétacé, 3) le batholite patagonien, et 4) les sédiments marins et continentaux ainsi que les basaltes du Crétacé supérieur-Miocène. Les roches du Jurassique supérieur-Crétacé et le batholite patagonien, formés dans un contexte d’arc volcanique et d’arrière-arc se superposent au socle métamorphique paléozoïque.Fondé sur la localisation géographique ainsi que sur le cadre tectonique et géologique, les dépôts de minerais de cette région se répartissent en trois groupes, du sud au nord, El Faldeo, Fachinal et El Toqui. Le Groupe El Faldeo (sud de 47°05'S) contient des skarns à Pb-Zn du Jurassique supérieur associés à des veines de sulfures massifs polymétalliques, localement recoupées par des minéralisations épithermales, riches en Au, et contenus dans des roches sédimentaires et volcaniques et/ou dans des roches du socle métamorphique. Le Groupe Fachinal (46°05' - 47°05'S) consiste en des dépôts épithermaux Au-Ag, se trouvant dans des roches volcaniques du Crétacé inférieur, excepté pour les dépôts de la Mine Silva et Manto Rosillo, où des skarns à Pb-Zn, se trouvent dans le socle métamorphique. Le Groupe El"

Jan 1, 1999