Search Documents

By M. P. Du Plessis

"The paper discusses coal research in relation to the special needs of Western Canada, with its large resources of lignite and subbituminous coals. Research programs are presented under the following headings: Coal Liquefaction, Pyrolysis, Fluidized-Bed Technology, Underground Coal Gasification and Supporting Investigations. Typical processes are presented and their relevance to Canadian coals is described. The longterm plan of the Alberta Research Council for coal research and the steps taken for its implementation are discussed. Finally, some innovative concepts arising from basic research in coal chemistry are discussed.Canada's Coal ResourcesCanada is richly endowed with coal reserves. With estimated ultimate reserves of 600 billion tons in O.76-m (2.5-ft) thick seams under less than 762 m (2500 ft) of overburden, Canada rank s fourth after the USSR, the USA and Chinatu (see Table I) . Canada's reserves are incompletely explored and estimates are constantly being upgraded. Preliminary information from deeper test-hole logs suggest that similar , if not larger, tonnages occur at depths greater than 762 m (2500 ft).The types of Canadian coals and their regional Distribution(2) is shown in Figure 2. Alberta's subbituminous Plains coal represents about 70% of estimated national reserves. A large portion of the coal can be mined at relatively low cost by surface mining techniques, and it is currently being used exclusively for power generation in conventional thermal plants. This coal, however , also represents a large potential .source of liquid fuels which could equal or exceed that of oilsands and heavy oil. Table 3 compares Federal Government estimates for resources and reserves of fossil fuels in Canada and their recoverable oil content or equivalent.A conservation estimate of only the reserves of thermal coal represents an oil equivalent of 27.6 billion barrels , which equals the recoverable reserves of oil-sand bitumen and heavy oil. A more realistic estimate is probably several times this amount. Although coal can be converted to many other end products, such as fuel gas and synthesis gas for hydrogen and ammonia production, liquid fuels remain the most desirable product mainly because they can be transported more cheaply over long distances and their high energy density makes them uniquely suitable as fuels for transport and agriculture."

Jan 1, 1981

By T. R. Yu, D. B. Counter

"In an effort to increase productivity, the use of fly ash as a binder for consolidated backfill was studied. From laboratory and underground tests f or its cementitious properties and environmental effects, it was found that a portion of Portland cement could be replaced by the same amount of type ""C"" fly ash to produce an acceptable consolidated rockfill product for use at Kidd Creek.The environmental concerns in terms of dust control and emanation of radon gas were unfounded from measurements. The dust count was comparable to the use of Portland cement only, or with ground blast furnace slag, and the radiation readings were low, averaging one-seventh the regulation level.Since May 1984, a total of over 100 000tonnes of fly ash has been consumed as a binder blended with Portland cement, producing over four million tonnes of consolidated rockfill. To date, the fill in the stopes has performed very satisfactorily, while yielding considerable cost savings.IntroductionThe Kidd Creek minesite, located 27 km north of the city centre of Timmins, Ontario, produces 4.5 million tonnes of base metal sulphide ore annually. The mining method for both No. I and No .2 mines is mainly sub-level blasthole stoping with delayed backfilling.No. 1 mine was developed with a shaft to a depth of 930 m in 1973 to recover the ore between the floor of the open pit at the 216 m horizon, and the 792 m horizon. Stopes are normally 18 m wide, 22 m to 65 m long, with heights varying from 90 m to 135 m. Vertical rib pillars between stopes are typically 24 m wide and sill pillars are 30 m thick.Pillar recovery is implemented after the consolidated rockfill placed in the mined stopes has cured for a period of at least three months. This allows a maximum recovery of the ore with a minimum of dilution, while also maintaining safe working conditions.No. 2 mine was developed from a second shaft, sunk to a depth of 1530 m in 1978, for the recovery of ore beneath the No. I mine. Sub-level stoping in No .2 mine is similar to No.1 mine in methodology, yet differs in sequencing, as no rib pillars are left."

Jan 1, 1988

By J. Bensabat, B. Figueiredo, A. Niemi, J. Rutqvist, C. F. Tsang

"A hydro-mechanical model was developed to study the interaction between mechanical deformation and fluid flow in the fault zones during CO2 injection and storage at the Heletz site which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The potential reservoir for CO2 storage at the Heletz site consists of three sand layers separated by lowpermeability shale layers. The potential consequences caused by fault reactivation, focusing on the shortterm integrity of CO2 storage, are evaluated. The difference in the results obtained by considering the three-layer as an equivalent layer storage formation is analyzed.INTRODUCTIONLarge-scale storage of CO2 in deep underground reservoirs may cause considerable pore-pressure perturbation as well as flux migration and concern has been raised over whether shear slip displacements may be induced in nearby faults, as a consequence of their reactivation. A state-of-the-art review can be found in Rutqvist (2012), which describes the various possible effects resulting from CO2 injection into a deep sedimentary basin, including those involved in reservoir stress–strain changes, micro-seismicity, caprock sealing performance, and potential fault reactivation. Moreover, several studies have recently shown how CO2 injection may produce seismic events both on major faults (i.e., large faults with large initial shear offset) (Cappa & Rutqvist, 2011a, b, 2012), and on minor faults that might have gone undetected during the site characterization, e.g., faults less than 1 km long and without detected initial offset (Mazzoldi et al., 2012).The present paper is concerned with the Heletz formation which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The Heletz site located at the southern Mediterranean coastal plain of Israel and the structure is an anticline fold with a crest of about 4 km by 2 km. The structure is gently dipping to the east, truncated by a pinch-out line to the west and subdivided into a number of blocks by transversal normal faults with small displacements. The water table is located at 300 m below the land surface. An areal sketch of the site with the elevation of the caprock and the location of the borehole that has been chosen for the CO2 injection experiment is presented in Figure 1."

Jan 1, 2015

By M. A. Mahtab, A. S. Burgess, R. G. Charlwood, P. O. Sandstrom, J. L. Ratigan

"Addressing a current operating and environmental concern, this paper first presents an overview of the design program for an underground radioactive waste storage vault. It then reviews the construction, operational and thermal-mechanical aspects of such a project. The relevant experience from major underground construction projects is reviewed and the paper concludes with brief comments on the design-oriented research and development requirements . 1. IntroductionA program to develop techniques for the ultimate disposal of high-level radioactive waste into geologic formations was announced by AECL in 1975 (Tamrnernagi, 1976), and is discussed more fully in a later document (Boulton, 1978). Our paper summarizes the studies caried out, as part of the AECL waste management program, by the authors and associates on the development of design concepts for a vault situated in crystalline rocks of the type present in the Canadian Shield.The design studies have been carried out in three phases, the elements of which are described in Section 2.1 (also see Fig. 1). The general vault designs are presented in Section 2.2. These provide for emplacement of either immobilized fuel or solidified reprocessing wastes in a room-and-pillar facility at a depth of 1,000 m.Section 3 reviews the principal design considerations from the construction, operation and thermal-mechanical response aspects. The concepts have been studied in both temporal and spatial domains, and the requirements and responses assessed in each as appropriate.Section 4 briefly reviews the availability of relevant experience from previous major underground construction projects. Finally, in Section 5, brief comments are given regarding design-oriented research and development requirements."

Jan 1, 1980

By John H. Schloen

"The object of this paper is to review electrolytic copper refining as it was in 1954(1), as it is now in 1984, and to comment on the many improvements which have been made in the last thirty years.In 1954, and even in 1984, the ASTM specification B 115 for cathode copper was 99.90% minimum copper plus silver content and 100% minimum electrical conductivity, IACS standard. However, to meet competition and to satisfy the requirements of the fabricators and the electrical industry, the electrolytic refinery must supply a product of 99.95% to 99.96% minimum copper content, and 101fJlo minimum electrical conductivity.The range of cathode impurities reported by 20 major copper refineries in 1954 are given in Table I.The much more rigid British Specification, DD 78, for high-purity cathode copper, specifies individual elements, as well as groups of elements, as shown in Table 2.The Svenska test has been replaced by a similar procedure which uses 2.r mm diameter wire. The ISO test is the one listed in the DD 78 specification. In Table 3, corresponding values for the Svenska and ISO test s are given for various wire bar coppers."

Jan 1, 1986

By A. Montini, M. H. Moys

"A conductivity probe mounted in the shell of the mill has been used to measure the behaviour of the load in the mill as a function of operating variables. It was found that certain properties of the conductivity signal correlate strongly with the per cent solids of the slurry passing through the mill; in particular the angular location ?D of the shoulder of the load is an increasing function of the per cent solids. A method for measuring the viscosity of the pulp discharging from the mill has also been developed. The use of the measurements in mill control is illustrated by simulating various control strategies for open circuit milling. It is shown that the use of ?D allows very tight but imprecise control of the slurry rheology in the mill, while the use of viscosity is subject to severe limitations in speed of response. A cascade control system involving both measurements provides adequate control of slurry rheology within the mill. Applications to closed circuit milling are discussed.IntroductionMultivariable control of milling circuits continues to receive a lot of attention in the literature. Hulbert and co-workers and Niemi, et al. have described the use of Inverse Nyquist Array (INA) techniques while Herbst has recently described the use of Optimal Control. It is significant that in neither of these three projects was any variable associated with the grinding mill itself (e.g. power or properties of the mill discharge) used in the control strategy. Pauw, et al.do, however, use mill power in their multivariable peak-seeking controller for pebble-mill control. Little work has been published on the use of measurements of the properties of the slurry being discharged from grinding mills, in spite of the fact that milling efficiency is known to be strongly affected by slurry rheology».Moys has recently developed a technique for measuring the dynamic behaviour of the load in the grinding mill. This method involves the monitoring of the response of a conductivity probe mounted in the shell of the mill which gives a measurement of the orientation of the load inside the mill. It was found that the load behaviour was strongly influenced by slurry rheology. In this project a technique was also developed for the measurement of the viscosity of the slurry in the mill discharge. It was, thus, decided that it would be worth investigating the use of these measurements in mill control schemes since direct control of the slurry rheology in the mill must inevitably increase the efficiency and productivity of the grinding circuit as a whole.This will be done by using the dynamic responses measured by Moys and Montini to simulate the behaviour of an open circuit ball mill. While the control of open circuit mills is of little interest, this simulation provides a simple but powerful demonstration of the advantage provided by these measurements, advantages which should apply to closed circuit operation of any mill type (including autogenous milling). Investigations into multivariable control of a closed circuit ball mill are currently nearing completion and will be published soon."

Jan 1, 1987

By J. L. Jambor, E. J. Reardon, E. C. Appleyard, J. A. Cherry

Since the 1957 initiation of deposition of mill tailings at the Heath Steele mine, New Brunswick, periodic detailed studies of the tailings geochemistry and mineralogy have been conducted, thereby providing a unique opportunity to examine the geochemical evolution of a sulfide rich mine>tailings impoundment. When deposited, the tailings contained about 85 wt% sulfide minerals, 1 wt% to 3 wt% carbonate minerals, and 12 wt% to 14 wt% alumino silicate minerals. Mineralogical examination of samples of the tailings from deep in the impoundment indicates that little oxidation occurred prior to tailings deposition. The mill process-water deposited with the tailings was neutral to slightly basic and contained low concentrations of Cu, Pb, Zn and As. Sampling of the tailings five years after deposition indicated that sulfide-oxidation reactions, occurring near the tailings surface, had decreased the tailings-water pH and increased the concentrations of Fe, S042-, Cu, Zn and Pb (up to 10 000 mglL, 25 000 mg/L, 2.5 mg/L, 200 mg/L, and 4.5 mg/L, respectively). In 1975, ten years after decommissioning, the tailings could be divided into three zones: an upper oxidation zone in which sulfide oxidation is actively occurring, a hardpan layer, 15 cm to 20 cm thick, composed of tailings cemented by secondary Fe minerals, and an underlying reduction zone in which the tailings are relatively tin oxidized (Boorman and Watson, 1976). Chemical analyses indicated the presence of low-pH waters containing very high concentrations of SOi-, Fe, and other metals (up to 63 600 mg/L SO42-, 28 600 mg/L Fe, 10 mg/L Pb, 600 mg/L Cu and 4000 mg/L Zn), suggesting that there was a period of intense sulfide oxidation between five and ten years after tailings deposition. More recent sampling, conducted some 20 years after the end of tailings deposition, indicates that relatively little change has occurred in the last ten years, thereby suggesting that the hardpan layer has provided an impediment to the downward movement of dissolved constituents. Analyses of the tailings solids show increased accumulations of many metals at or near the depth of the hardpan layer. Evaluations of the long-term evolution of the tailings can be enhanced by comparison of descriptions of the tailings with descriptions of the gossan that overlay the massivesulfide orebody prior to mining. At Heath Steele, this comparison suggests that many of the mechanisms controlling the distribution of metals in the tailings will probably persist over geologic time.

Jan 1, 1992

By J. M. Beeckmans, S. G. Butcher, M. Goransson

"The counter-current fluidized cascade is a novel and potentially efficient pneumatic gravity separation device. Data are presented on over 150 runs of cleaning Alberta thermal coals, covering several size ranges. The coarser sizes of coal were processed in admixture with a fluidizing medium consisting of 0.5-by 0.1-mm hematite (or magnetite) and limestone particles. The partition curves for coal particles larger than about 3 mm, mixed with fluidizing medium, showed that the sharpness of separation achievable with the cascade approaches that of wet heavy medium processes, whereas with particles in the size range of 3 by 0.6 mm the sharpness of separation was comparable to that of a Baum jig. Useful cleaning was also achieved with particles smaller than 0.6 mm , Throughput rates of up to 11 tonnes per metre width of cascade per hour were achieved, with no indication of a deterioration in performance.IntroductionPneumatic coal beneficiation has steadily lost ground vis-a-vis hydraulic beneficiation during the past quarter century, primarily because of the sharper separations achievable with the latter methods. Nevertheless, there are certain inherent advantages of pneumatic separation methods which would give them an advantage in the market place were it possible to increase their efficiency to be technically competitive with those of hydraulic processes. These advantages are a dry product, resulting in a higher calorific value per ton, and avoidance of the problems associated with treatment and storage of process waste waters. Also, although it may be necessary to dry the raw coal prior to pneumatic processing, the dry rejects produced constitute an ideal fuel for a fluidized-bed combustor, which could provide heat both for drying the coal and for other purposes."

Jan 1, 1982

By M. A. T. Cocquerel, J. G. Eacott

"Simulation techniques may be used to optimize existing processes and plant operations, and in plant design at the engineering study stage of a project . This paper describes the latter application, using a computer, to optimize the concentrate stockpile requirements of a modern copper smelter.A large open-pit mining operation is envisaged and it is assumed that copper concentrate is smelted in two flash furnaces. The proposed mining plan gives rise to metaffurgical considerations in smelting which dictate that concentrate blending is carried out in the early years of operation in order to eliminate wide variations in the grade of concentrate charged to the furnaces . Stockpiling facilities are therefore necessary for blending purposes and also to provide a strategic reserve of concentrate to ensure continuity of concentrator and smelting operations.The objective of the study is to determine the optimum size of concentrate stockpile required to take account of both metaffurgical and strategic considerations. Two separate simulation models are developed to achieve this objective. The first model is used to determine the minimum size of stockpile necessary for blending purposes to smooth out variations in concentrate grade between 15 - 60% Cu, with associated 34 6% Fe, respectively, and ensure that the concentrate fed to the furnaces does not faff below 12% Fe, which is considered a minimum for good smeltability.The second simulation model covers a projected three-year operating period and indicates the maximum size of stockpile which is likely to develop during scheduled and unscheduled shutdown periods in the concentrator and smelter.Covered storage volume and conveying facilities for the optimum size of concentrate stockpile can be designed based on the results generated by the simulation models."

Jan 1, 1980

By John E. Udd

"Mining research at CANMET is delivered by the Mining Research Laboratories Division (MRL), with facilities in Sydney, Nova Scotia; Bells Comers, Elliot Lake, and Sudbury, Ontario; and Val d'Or, Quebec. This paper gives an overview of the work of the Division as of early 1993. An addendum, at the end of this paper, describes the organizational changes that will take place in April 1994. IntroductionCANMET, the acronym for the Canada Centre for Mineral and Energy Technology, is the name by which the organization founded in 1907 as the federal Mines Branch is presently known. The name was changed in 1974, in order to give recognition to the importance of both minerals and energy technologies in the activities of the Branch. Further reorganizations have taken place since 1987. As a result of these, CANMET has assumed the status of a Sector (equivalent to the Geological Survey of Canada) and has been organized into four branches.The organization as a whole functions in an environment of semi-matrix management. Some of the ""line"" Divisions report to Directors-General for the appropriate branches while other, larger divisions, report directly to the Assistant Deputy Minister.The second dimension of the organizational matrix is composed of a number of ""staff' divisions which report to the DirectorGeneral for Policy and Planning. Each of these Divisions performs a function which is common to all of the ""line"" divisions. For example, the Research Projects Office is responsible for monitoring the range of research activities of CANMET and for recommending allocations of funds for both research contracts and operating budgets. The Library and Documentation Services Division is responsible for CANMET publications and information services. Likewise, the Engineering and Technical Services Division provides support through, among other services, the construction of specialized laboratory equipment."

Jan 1, 1994

By R. Frank Chiappetta, E. B. Wilson

"The maintenance records for AL-60 airlegs at Falconbridge Ltd. are used to demonstrate some of the procedures for the analysis of such data.The data are not representative of pure failure s of one type or another. In fact, the records are for the undefined pseudo-failures which are usually found in industrial operations. However, because the machines are brought to the shop only when inoperative, the individual recorded components are treated as failures. Manual calculations are conducted to show the analysis of variance (ANO VA) approach to determine whether certain data can be combined; only a limited number of the 206 machines being considered. The manual procedures continue with the weighting of the suspensions; i.e. terminations f or reasons other than the failure of the given component. After the data are sequenced in the proper order, the nature or pattern of the data is determined using the Kolmogorov-Smirnov (KS) test.It is recognized that these manual examples must be replaced by compute r methods 10 process voluminous data of this nature. Such programs are developed and available. However, a program called RELCODE is used in this case to correspond to the manual examples and to take into account the suspensions. These analytical procedures form the basis for those studies required for good maintenance management."

Jan 1, 1985

By D. A. Stokes

"In October of 1980, Fording's 15 000-ton capacity clean coal silo was put into operation. The silo was unique in that it was designed to allow the mass flow of material, coupled with a sophisticated computer-controlled dynamic loadout/weighing system.On May 1, 1982, an explosion, attributed to a methane buildup, devastated the top of the silo. .As a contingent plan to minimize the effect of the production loss the conveyance to the silo top was reconstructed and the silo' was back in operation by mid-June 1982, although the silo top was left open to prevent further methane buildup. As dust emissions occurred during loading ofthe silo, an extensive study was undertaken to establish dust control for the silo, while at the same time providing methane detection and control.The study, conducted for Fording by the Cambrian Engineering Group of Calgary, involved an extensive search and investigation of existing coal silos. The study concluded that there IS no universally accepted method of controlling methane emissions in coal silos.The study also produced a unique conceptual design for handling methane, while at the same time, protecting the environment . Fording's Clean Coal SiloThe silo, located at Fording Coal's Fording River metallurgical coal operation, is utilized for the storage and load out of cleaned thermally-dried metallurgical coal.The silo was constructed in 1979 and 1980 to reduce unit train loadout times and to facilitate the handling of “special shipments"" of coal. The silo went into operation in October 1980, under manual control and utilized computerized, automated loading by February 198I.The silo is 21 m in diameter and 76 m high, with a nominal capacity of IS 000 live tonnes. The coal storage portion of the silo is 21 m in diameter and 48 m high, utilizing 2 steep-angled hopper outlets allowing mass flow of the stored coal during train loading. Each hopper has a control gate and a discharge chute, one chute for bulk loading, the other for trim loading of coal into the rail cars."

Jan 1, 1986

By B. Stuckert, P. Sheehan, J. Balfour, B. (Manas) Das, D. Fawcett

"With the growth of large scale surface mining operations, waste disposal and stability of waste dumps pose a challenging problem to engineers. Vibrations due to blasting operations proximal to these dumps further complicates dump design. Many dumps which are statically stable may become unstable due to the effects of blasting vibrations.A joint project between CANMET and Smoky River Coal Ltd. has been initiated to study the dynamic stability of waste dumps. The study involves development of an analytical algorithm combined with field monitoring to assess dump performance.Another objective of the study is to provide baseline data for a vibration attentuation relationships for sedimentary rock (coal) environments: most studies to date are for base metal mines. The effect of dump thickness on vibration response is also addressed.The key objective of the study is to present a methodology for assessing the dynamic stability of waste dumps. Implicit in this methodology are a number of assumptions concerning vibration attenuation in sedimentary rock environments, and response of the dump material to induced vibration. Where possible, these assumptions have been compared with monitoring data as a check on their validity."

Jan 1, 1989

By Kurt D. Mitchell

"This paper discusses general application for A C variable frequency drives in the mining industry. A review of induction motors characteristics, adjustable frequency controller fundamentals, and three commonly used controllers is presented. General application guidelines for the three different types of controllers; variable voltage input , current source input and pulse width modulated are then reviewed in detail, and an example of the economic benefit of this technology is discussed. IntroductionSoon after static DC variable speed drives were well established in industry, a need for static AC variable speed drives was seen. The first technical papers describing possible systems appeared in the mid-1960s, with commercially available units arriving in the early 1970s. Without exception, static AC drives are substantially more complex than their DC counterparts, but they have some very desirable properties. As compared to DC motors, AC motors are less costly, physically smaller, more reliable, require less maintenance , easily sealed, have good load regulation, are able to run at higher operating voltages, and have little danger of over-speed runaway . These properties are particularly desirable in explosion-proof, submersible or difficult accessibility applications.Variable speed AC drives are now a proven technology. available in packages from Sub-horsepower to hundreds of horsepower, from 115VAC to 4160 VAC. This paper covers the principles of operation of three common types of controllers, application criteria, motor consideration and finally an example of how an AC variable speed drive can pay for itself in terms of energy savings."

Jan 1, 1986

By Marek Mika

This Paper has been prepared to be presented at the 23rd World Mining Congress & Expo ? Montreal 2013. It presents the idea how to carry out the shaft sinking operation, going through highly water-bearing and very weak rock strata, giving as an example one specific shaft sinking project which is being executed for one of the Polish collieries by our Shaft Sinking Company Content 1. Introduction. 2. Hydrogeological conditions within the area of the shaft. 2.1. Hydrogeological conditions assumed at the stage of designing. 2.2. Hydrogeological conditions encountered in the course of sinking. 3. Designed shaft lining. 4. Procedures for the shaft sinking. 4.1. Designed procedures of the shaft sinking. 4.2. Procedures for preservation and strengthening of the shaft lining and the surrounding rock strata. 5. Technological guidelines for proceeding with the shaft sinking ? selection of special methods. 6. Options for mechanization of work for the selected method. 7. Conclusions.

Aug 1, 2013

By D. L. Churcher, R. J. Perry

"In recent years much work has been don e to examine alternate underground backfill support systems with the objectives of improving ground support and reducing mining costs. This report deals with the work conducted at Placer Dome Inc.’s Dome Mine to develop a high density backfill system, taking advantage of the unique properties of this fill material, to address a backlog of large open stopes to sustain stable minewide ground conditions for future generations of Dome miners.IntroductionDome Mine began its existence in 1909 with the discovery of visible gold on a dome shaped outcrop located west of Porcupine Lake in northern Ontario. The orebody beneath this outcrop has supported one of Canada’s premier gold mining operations for 80 years. Production during this time of over 46 000 000 tons of ore has resulted in the recovery of II 500 000 ounces of gold and 2 000 000 ounces of silver. Mining continues today at a production rate of 3500 tons per day, with ore coming from both underground and open pit operations.During the life of the mine, different underground mining methods have been used to extract the ore from a complex deposit consisting of single and multiple vein structures.Cut-and-fill mining was introduced in the 1930s using sand fill and later hydraulic fill for support and to provide a working platform. A total of 1 800 000 tons of sand fill and 7 300 000 tons of hydraulic fill have been placed underground in cut-and-fill stopes. Until the late 1960sshrinkage mining was used extensively, particularly in narrow, steeply dipping zones. Bulk mining with small diameter longholes was introduced about this time, to take advantage of low production costs. Longhole blasting has often been used to recover low grade ore from the walls or sills of old shrink stopes, resulting in large open stopes. Backfilling of these open holes has been restricted to smaller stopes and associated with local ground conditions.In the late 1970s it was recognized that the number of large open holes which were being generated presented serious regional and minewide stability problems for future operations. With higher gold prices, economic ore reserves were being tied up in areas adjacent to multi-level open stope complexes. To stabilize these stopes and allow access, backfilling would be required."

Jan 1, 1990

By Marc Lavigne

"The Lac Knife graphite deposit was estimated, as part of a feasibility study, using a geostatistical ore reserve estimation method: ordinary kriging. Based on the geology and its interpretation, the results of a variogram study, and the statistical parameters of the grade distribution of the core samples and the composites through the mineralization, the deposit was divided into three separate zones (west, centre and east), and each of these zones was then analyzed and kriged independently.The geological ore reserve estimation results of ordinary kriging are compared to the results of a conventional method (sections) used previously. The two methods gave almost similar reserve figures. The conventional method provided a +2% estimation for tonnage and + 10% for grade because it ignored the spatial relation between sections and samples, and ordinary kriging gave a more accurate longitudinal definition of the deposit.Finally, the paper concludes with the advantages of proceeding with ordinary kriging, namely: higher flexibility (change of cut-off grade), better deposit resolution and enhanced selectivity for the design of the open pit.IntroductionWithin the context of a complete feasibility study for the Société d' Exploration Minière Mazarin Inc., specialists of the Mines and Geology Division of Roche Ltd., Consulting Group, defined a modelling method appropriate to the graphite deposit of the Lac Knife property near Fennont. Many patterns were considered. Based on the geology of this deposit, the planned mining method, the statistical parameters of grade distribution and the variogram study, the process of reserve estimation retained was to use the ordinary kriging in a selective way. It was required because the geometry of the deposit is such that it was unthinkable to apply ordinary kriging without restrictions.This paper gives a detailed explanation of the observations and interrogations which led to the choice of this ore reserve estimation method, and the calculation procedure itself."

Jan 1, 1991

By G. Kollberg

"IntroductionThe SALA Caravan Mill system represents a proven concept for the design and operation of mobile and semi-mobile ore dressing plants.The Caravan Mill has been developed to meet the demand for a flexible processing plant to be used for small and medium-sized orebodies or for pilot investigations of deposits directly at the mine site e •The first Caravan Mill installation was put into operation in 1970 and a number of plants have been delivered world-wide since then.The Caravan Mill system has great flexibility both in capacity, ranging from 50 to 1000 tons per day, and in process combinations. The process modules available are:• crushing by jaw and cone crushers;• pre-concentration by the Dyna Whirl Pool dense media system;• grinding by wet rod or ball mills;• separation by gravity, magnetic, flotation or leaching-CVP adsorption methods;• dewatering by lamella or conventional thickeners and vacuum filters.To form complete plants, auxiliary equipment is also available, such as:• bins, feeders and conveying systems;• power generator units;• water tank and pump for process water;• interconnecting piping and cables;• erection and service tool kits;• set of spare and wear parts.For mine sites with rainy or winter conditions, a plastic tent with air heater can be supplied to cover the ore dressing equipment. Each module is workshop assembled complete with slurry pumps, internal pipe work, electric wiring with plug-in connections, hoses, etc., all arranged for quick and simple connection between the units. Before delivery, each unit is tested in the workshop."

Jan 1, 1982

By S. McCarthy, K. E. Waters, A. Jordens

The beneficiation of rare earth (RE) element bearing minerals has become an active area of research as applications for these elements grow while the supply to non-Chinese consumers is restricted by export quotas. One of the most interesting beneficiation techniques for RE minerals is froth flotation as their unique chemistry suggests that collectors with a specific affinity for RE cations should be able to selectively recover these minerals. Existing literature, focusing mainly on bastnäsite flotation, identifies hydroxamic acids as excellent collectors for RE minerals. The high stability of hydroxamate-RE cation complexes is the explanation most often offered for the observed selectivity of these reagents in bastnäsite flotation however some research has also suggested that mineral solubility plays a crucial role in the success of hydroxamic acid flotation of RE minerals. This work investigates the interaction of allanite, a relatively insoluble RE-silicate mineral, with benzohydroxamic acid using zeta potential measurements and microflotation. The effects of Fe(III) and Fe(II) ions as potential activating ions (cations that form stable hydroxamate complexes) on benzohydroxamic adsorption to the allanite surface are investigated as a potential solution to promote hydroxamic acid adsorption. The results indicate that the optimum conditions for separation of allanite from quartz occur at pH 4 using FeCl2 as an activator for benzohydroxamic acid adsorption.

Jan 1, 2014

By W. D. Fogwill, P. J. Clarke

"The Dawn Lake uranium deposits are located 340 km north of La Ronge, Saskatchewan, in the Athabasca Basin between the Midwest Lake and Rabbit Lake deposits. Four zones of uranium mineralization, called the ""11, 14, 11A and 11B Zones,"" lie within the Athabasca Sandstone, at the sub-Athabasca unconformity and in the basement.At Dawn Lake, approximately 100 metres of Helikian Athabasca Group clastic sediments overlie Aphebian Wollaston Group pelitic and calcareous metasediments and pegmatites. Uranium with some nickel, cobalt and copper, occurs near the sheared stratigraphic contact between calc-silicate gneiss and graphitic, pyritic pelite. The mineralization lies in an area of low magnetic susceptibility which is thought to represent a rock sequence lying stratigraphically high within the Wollaston Group. There is no obvious vertical displacement of the unconformity by faulting, despite considerable brecciation, shearing and slickensides seen in the basement rocks. This suggests horizontal displacement on steeply dipping wrench faults as the main tectonic control along the 11, 11A and 11B trend.Below the Athabasca unconformity, the Wollaston Group rocks are altered to fine-grained mixtures of clays, chlorite and silica commonly called regolith. Along the mineralized trend post-Athabasca fracturing and (or) compaction have occurred through this clay-rich alteration zone, causing the steeply-dipping primary foliation to become contorted. This ""crenulated"" horizon can reach depths of 35 metres below the unconformity and is thickest along fault zones in the calc-silicate rocks. The ""crenulite"" is a distinctive unit which at Dawn Lake is commonly found above pods of ore located deep below the unconformity.Much of the mineralization in the 11A and 11B Zones occurs above, beside and below the thickest part of the crenulated zone, although the crenulated rock itself contains negligible amounts of carbonate, pyrite and uranium. Intense vuggy alteration and collapse breccias are found in calc-silicate rocks deeper and to the west of the 11A and 11B mineralization. There are at least two ages of uranium deposition in the basement zones, shown by small bright cubes of ""pitchblende /"" overgrown and replaced by duller botryoidal ""pitchblende II. ""Sooty pitchblende and yellow secondary minerals are the result of still younger reworking.The geological setting of mineralization, along the contact between carbonate-rich calc-silicate rock and pyritic pelite, suggests that the uranium was concentrated at a pH/Eh boundary located between deeply weathered, carbonate-rich and sulphide-rich basement rocks."

Jan 1, 1986