Search Documents

By Jeff Bird, Xijia Wu, Prakash C. Patnaik

"Prognosis and health management (PHM) is an evolving suite of technologies intended for application to the life cycle management (LCM) of mission/safety critical systems, with anticipated results, which will: - Reduce life cycle cost - Enhance operational safety and readiness - Assist in maintenance decision-making - Enable autonomic logistics While it is emphasized in the United States that future multi-mission fighter aircraft such as Joint Strike Fighter (JSF) must have PHM capabilities, Canadian initiatives also recognize the need to implement such schemes for future and legacy military and civil aerospace systems. With respect to four major technology areas of PHM, i.e., i) advanced sensors, ii) data analysis and fusion, iii) life consumption evaluation, and iv) predictions with reliability/risk assessment, there has been advanced technologies developed by NRC and others within Canada: - Aircraft/engine instrumentation and airborne data recording systems - Signal analysis and data fusion - On-line engine health monitoring - Physics based models for engine material failure modes and life prediction - Autonomic crack growth analysis for damage tolerance of engine components - Mission severity analysis algorithm - Probability, reliability and risk assessment This presentation reviews the above technologies in relevance to PHM, emphasizes the need to have physics based models and outlines the future R&D needs for integration and implementation of these technologies suitable for the advanced and legacy aircraft."

Jan 1, 2004

"This document sets out the Exchange’s expectations and requirements for a valuation of mineral properties and outlines: the general purpose of valuation reports; guidelines respecting circumstances where the Exchange will require a valuation report; and valuation standards, guidelines and methods that are generally acceptable to the Exchange, 1. IntroductionThis Appendix sets out the Exchange's expectations and requirements for a valuation of mineral properties and outlines:(a) the general purpose of valuation reports;(b) guidelines respecting circumstances where the Exchange will require a valuation report; and(c) valuation standards, guidelines and methods that are generally acceptable to the Exchange.Mining industry standards and guidelines for valuations and valuation reports can be found in the Canadian Institute of Mining, Metallurgy and Petroleum Standards and Guidelines for Valuation of Mineral Properties (""CIMVal"") published in February, 2003 (www.cim.org). CIMVal consists of two parts, Standards and Guidelines. The Standards are mandatory and must be followed in order for a valuation to be CIMVal compliant. The Guidelines in CIMVal are not mandatory, but are strongly recommended.The Exchange requires that CIMVal Standards be used by Issuers and their professional advisors when preparing valuations and valuation reports on mineral properties. The CIMVal Guidelines should be followed by Issuers and their professional advisors in preparing valuation reports on mineral properties, with the exception that the valuation methods and guidelines under Section 4 Acceptable Valuation Methods and Guidelines below, must be followed."

Jan 1, 2003

By S. Kelebek, Gerhard W. Heinrich, Peter F. Wells

"The review and optimization of process stages is an integral part of the program to improve the metallurgical performance of the Strathcona Mill. Improved primary grind size distributions, streamlining of rougher-scavenger circuits and increased platinum recoveries were the target of plant and laboratory scale tests. The results can be summarized as follows:• Decreasing the primary grinding cyclone vortex finder diameter for nickel/copper ore gave significant increases in overall copper recovery and improved rougher flotation selectivity.• The scavenger flotation stage in the circuit treating copper ore was found to contribute little to this circuit's copper recoveries -yet to be essential for acceptable recoveries of nickel, platinum and gold. The elimination of this stage by re-routing the tailings from the copper ore rougher into the nickel/copper ore rougher feed has lead to lower gangue recoveries to the nickel concentrate and to improved copper-nickel separation, while reducing equipment operating costs.• Surface aging effects such as oxidation are known to decrease flotation recoveries of platinum minerals such as sperrylite. The conditioning of an intermediate non-magnetic process stream with copper sulphate prior to thickening increased the platinum recoveries in the subsequent flotation stage by approximately 10%."

Jan 1, 1996

By G. Roy

Interest in metal-hydrogen systems can be manifold. Small amounts of hydrogen adsorbed by elemental metals and alloys usually result in strong changes in the physical and mechanical properties of engineering materials. Overwhelmingly, these changes, viz. hydrogen embrittlement, are considered deleterious with respect to structural performance of engineering materials. However, the changes, often studied by metallurgists and metal physicists, can present new possibilities and applications. A prominent example is the recent interest in safe, solid-state hydrogen storage in metallic lattices. In a new laboratory in MTL, Ottawa, a study has been initiated to investigate the effect of "micro- and macro- alloying" of Al and Mg powders with hydrogen (in high-energy mechanical alloying mills) on plastic deformation in metal and metal hydride structures. It is anticipated that high-rate impacting and subsequent grain refinement in the mill will have an effect on hydrogen storage capacity in lightweight magnesium and aluminum alloys. First examination of the state-of-stress by X-ray diffraction in high-rate milled, nanostructured pure aluminum, aluminum milled with a solid surfactant, and aluminum or magnesium alloy milled with hydride and/or gas hydrogen will be presented.

Jan 1, 2005

By C. A. Pickles, K. Mackowiak

Black Thor chromite ore from the Ring of Fire deposit in Northern Ontario was carbothermically reduced in a microwave system to produce a ferrochromium alloy. The as-received ore contained 43.0% Cr2O3, 19.9% Fe2O3, 14.5% MgO, 13.4% Al2O3, and 7.0% SiO2. Activated charcoal was utilized as the reducing agent. Firstly, TGA/DTA and permittivity studies were carried out in order to determine the relationship between the reduction process and the microwave susceptibility. Secondly, microwave reduction experiments were performed on the chromite ore. The variables investigated were; the amount of carbon, processing time, input power and type of atmosphere. A maximum chromium grade of 76.1% and a chromium metallization of 82.7% were obtained for a processing time of 20 minutes, a power input of 800 W, and a carbon addition of 15% in an argon atmosphere.

Jan 1, 2017

By I. Takahashi

Recently, electronic devices have become smaller for some kinds of electronic devices, thermal dissipation and electrical conductivity of conventional Fe based alloy becomes insufficient. We selected the Cu-Fe based alloy CDA19400 and optimized the wire manufacturing process. Precipitates during aging treatment were observed by TEM. The size and distribution of the precipitates varied according to solution treatment temperature. With solution treatment at 950°C, the precipitates of y-Fe as fine as 10 nm were distributed dense in the copper matrix with coherency. For the solution treatment at 750°C, y-Fe of approximately 200 nm was observed. Comparing heat resistance of drawn wires, the material at 950°C treatment was superior. Electrical conductivity decreased from 63% IACS upon aging to 29% IACS by drawing. It is considered as particular phenomena for wires where materials are drawn with high reduction ratio. By the optimized manufacturing process, we successfully developed a new wire that has superior in strength, thermal conductivity, electrical conductivity, heat resistance and repeated bendability.

Jan 1, 2007

By Douglas H. Silvey

"The historical transformations in fire -resistant conveyor belt compositions in the past 20 years have been influenced by factors of material cost, changing flame and burn test requirements, material replacements, adhesion and oil resistance considerations, increased responsibility and legal liability. Specifically, this has resulted in a swing from neoprene-cotton belts to S.B.R. blends and synthetic fibre carcasses, and tighter quality control and documentation of test data.Flame dynamics are discussed and the function and performance of the multiple types of flame-resistant additives in the flame front are presented. Specific flame and burn test requirements are described. The belt manufacturers' requirements and criteria in selecting the types of flame-resistant additives are presented.The author will describe the composition of the types of flame-resistant compounds used in a practical production, the belts that are available on today's mark et and future developments in requirements that may further transform the composition of fire-resistant belts.IntroductionThe historical transformations of conveyor belt compositions in the past two decades have been based on factors common to those leading to changes in man y organic compositional products. These factors are material cost, new materials, the customer' s changing requirements, government regulation s and increased manufacturer' s liability.As a basis for understanding the product, I will provide a brief breakdown of the conveyor belt composite. Figure 1 represents a cross section of a typical belt. A skim rubber coats each fabric ply of the belt carcass and is of a different rubber composition than the outside layer of rubber which forms the cover. This outside cover layer is designed to protect the belt from environmental factors such as heat, oil and abrasion, and other factors involved in the service condition s under which the belt will operate. In the case of fire-retardant belt s, both the skim coat encapsulating the fabric plies and the outer cover must contain sufficient fire retardancy to overcome the contribution to burning of the decomosition products of the fabric."

Jan 1, 1982

By L. A. M. Castro

As Canadian mines progress to greater depths, magnitudes of induced stresses increase, becoming high enough to cause rock mass damage and failure during excavation. In addition, depending on the orientation of key geological structures in relation to the in-situ stresses, induced shear loading can be developed on these structures, creating the potential for: a) remobilization of existing geological structures, b) formation of new seismically active structural zones, created through rock mass damage and coalescence along such structural zones, and/or c) interaction between existing and newly created structures. Numerical analyses were carried out to investigate four possible factors that might cause fault slip on controlling structures, namely: (a) unclamping, (b) day-lighting, (c) stress rotation and (d) pillar shear. Application to an underground mine in the Sudbury Basin allowed verification of these factors and the proposal of two alternative mine planning methods to limit fault slip on key structures: (1) pillar clamping and (2) stope sequencing.

May 1, 2009

By J. Kang

There is increasing demand to utilize aluminium alloy sheets and their spot welds by the automotive industry. While traditional uniaxial tensile tests only determine mechanical properties to small strain, direct measurement of the constitutive behaviour of aluminium alloy spot welds at large strain remains a challenge. A technique was successfully developed using digital image correlation coupled with shear tests to directly measure the constitutive behaviour of an AA6022-T4 spot weld to large strains. The results show that the spot welding process not only decreases the yield strength but also lowers the work hardening rate of the nugget versus the base material. Details of sample preparation, experimental approach and results will be discussed.

Jan 1, 2011

By K. Soldenhoff

Mantra Resources Ltd is developing the Mkuju River project is southern Tanzania. The uranium deposit, hosted in ?Karoo? sandstone, is surface outcropping with the majority of uranium mineralisation occurring in the finer clay component of the ore. A flowsheet, consisting of ore beneficiation, acid leaching, RIP uranium recovery and direct precipitation of the uranium product, was developed and successfully demonstrated in continuous mini-plant operations at ANSTO. The selected flowsheet overcomes the difficult slurry rheology, arising from the clay component of the ore, by eliminating the need for a CCD plant. The RIP process was found to contribute to a high uranium extraction, by eliminating ?preg-robbing?, at a relatively low acid addition in leach, with the potential to eliminate ferric ion and oxidant additions.

Aug 1, 2010

By R. A. McIvor, R. S. Rafuse

"INCO Limited purchased a custom designed mobile hoist rope winder/tensioner in 1988 from TimberLand Equipment Limited to handle Large hoist ropes and serve as an emergency hoist. This paper describes the operation of the winder/tensioner and some of the different applications that the machine has been used to handle large loads.IntroductionINCO Limited operates 24 mine hoists in the Ontario Division and has approximately 50 miles of mine hoist rope hanging in the shaft plus an equal amount on spare reels. The mine hoist ropes range in size from )( inch to 2.305 inches in diameter with the majority being 1 3/4 inches and above. Prior to the procurement of a new high powered winder/tensioner in 1988, the mine hoist ropes were handled with a variety of methods and equipment using hydraulic or pneumatic powered reel winders. The largest such reel winder has a pull rating of 8000 Ibs and travels approximately 40 ft/min. Head ropes for the tower mounted friction hoists were installed and removed using a magazine on the hoist drum to wind and unwind the rope because the loads were greater than the capacity of the existing machinery. It was recognized that a large high capacity machine would improve the productivity for handling the larger hoist ropes and a feasibility study was undertaken to determine the parameters for such a machine."

Jan 1, 1995

By K. C. Corin, M. S. Manono, J. G. Wiese

Depressants play a crucial role in the flotation of PGM bearing ores as they prevent naturally floatable gangue (NFG) from reporting to the concentrate. This action is regarded as critically important because less dilution of the concentrate means lower costs for downstream processes. However, abnormal water conditions (such as high concentrations of ions) in the flotation system can modify the selectivity of these depressants. It is well known that the existence of selected electrolytes in water can alter the behaviour of some polysaccharide depressants by enhancing their adsorption onto gangue minerals and thereby prevent naturally floatable gangue from moving into the froth phase. Concurrently these same electrolytes may enhance frothability, owing to their stabilising effect on the bubbles within the system. Plant water at various ionic strengths was investigated against depressant type and dosage in order to understand electrolyte-depressant interactive effects during the flotation of a Merensky ore, using entrainment, rate of NFG recovery, and total gangue recovery as proxies. The study showed that the rate of NFG recovery per unit mass of water decreased with increasing ionic strength at all dosages, however the total amount of gangue reporting to the concentrate increased with increasing ionic strength at all depressant dosages. Thus, this paper attempts to consider the effects of both ionic strength and depressant dosage as individual factors within flotation. It further looks to investigate whether any interactive effects exists between these two factors when considered simultaneously.

Jan 1, 2016

By F. Rosenblum, P. Spira

"A correlation has been established between the oxygen demand of Brunswick Mining and Smelting ore and flotation results at the bench, pilot plant and operating plant scale. A method of dete""1llining the aeration requirement of sulphide ores on the basis of this correlation is presented. It is shown that abraded iron from grinding media plays an important role in aeration and flotation. Laboratory grinding must therefore be conducted under controlled conditions with suitable grinding media in order to obtain the true aeration requirement of the ore.A method of evaluating aerator efficiency, also based on oxygen demand measurements, has been used successfully at Brunswick Mining to design pilot plant and full-scale aeration systems.1. IntroductionPre-flotation aeration of sulphide pulps has been practiced in the Noranda Group for many years to help in the depression of pyrite and pyrrhotite and to promote chalcopyrite and/or galena. Recently, two out of three parallel circuits at the Brunswick Mining and Smelting Corp. Ltd. concentrator have been converted on a test basis to a new flowsheet incorporating aeration as a basic step. Among other benefits, a substantial decrease in the middlings load has been achieved as a result of improved pyrite rejection. There has been increasing interest in other organizations in the potential advantages to be derived from' aeration in terms of improved metallurgy and/or decreased reagent consumption."

Jan 1, 1978

By W. L. Strand, D. N. Madge

"Experimental and pilot operations in bituminous sand processing require due care and attention in the design and analysis of measurement programs. This paper deals with a case study in experimental design and data analysis for a series of experimental campaigns that have been conducted over the past five years by Kilborn Western Inc., acting on behalf of Bitmin Resources. Beginning with the design of the experiment and following into the use of linear and nonlinear regression models, the phenomenology of bitumen extraction is illustrated. The final testing program tested 13 oil sand types as well as a wide range of process variables for all the unit operations of the complete process.The program was successful in developing process fundamentals and scale-up criteria. Several phenomenological models were proposed and tested. Their range of applicability was explored. This paper illustrates the range of applicability of these models and discusses the development of alternative models.IntroductionOver the past five years Kilborn has conducted a series of bench scale and pilot scale experiments designed to explore the phenomenolgy of a new concept in medium temperature processing of bituminous ores. These experiments at feed rates ranging from .1 to 24 t/h were conducted on water wet sands from the .Athabasca region near Fort McMurray. They were based on experimental designs chosen to provide a systematic means of identifying the response surfaces of the process over a range of conceptual designs. The following diagram shows the experimental arrangement:"

Jan 1, 1998

By A. Abadías Llamas, N. Bartie, M. Stelter

Evaluating the economic viability as well as the sustainability of the Circular Economy (CE) system requires a deep understanding of the distribution of all elements, compounds, alloys, materials etc. in flows. In this paper, the circularity of the copper value chain, including primary and secondary processing, is rigorously evaluated. The studied system comprises the metallic copper production from primary sources (from mineral to metal), copper-containing commodity production (copper is mixed with other metals) and copper recycling through secondary smelting to close the loop. This is linked to photovoltaic (PV) panels and battery storage. A simulation model of this system is created using HSC Sim, considering more than 30 elements (and its various compounds), 180 unit operations and 800 flows. From the mass and energy balances obtained through the simulation, an exergy analysis is conducted to evaluate the resource consumption from a second law (entropy) perspective. Additionally, these results are complemented through a Life Cycle Assessment (LCA), the recovery of technology elements and by-products is discussed, while quantifying the losses through the value chain. Through the digitalization of the complete system, a better CAPEX and OPEX understanding of the metal recovery and losses can be obtained, as well as the associated resource consumption and environmental impacts. New flowsheets and technologies can be evaluated. Several scenarios show how the resource consumption and the environmental impacts are affected by the recovery of different materials to produce different products. INTRODUCTION A key challenge of the circular economy (CE) is the linkage and optimization of both resource and energy efficiency of the (renewable) energy infrastructure and the resource cycle depicted by Figure 1 simultaneously. In addition, the CE requires the linkage of all stakeholders as shown by Figure 1. This has been discussed in some detail by Reuter and Bartie (2019) and Reuter et al. (2019). Copper and all its associated technology elements is one of the key enabling metals that is an economical copper colored thread through CE society (Reuter & Kojo, 2014). The Metal Wheel (Figure 2) shows the linkage of and recovery of various elements associated with copper and other carrier metals. This reveals that copper acts as an important carrier metal because of its properties i.e. the wealth of technology elements it carries from geological ores, but also its capacity to act as solvent of valuable elements and thence a key closer of various complexly connected element and material cycles when these technology elements are released during copper refining. The same applies to all other carrier metals of modern CE society as shown for example recently in a lead policy brief (Blanpain, Reuter & Malfliet, 2019).

Jan 1, 2019

By L. Contretras

This study has as an objective to analyze and to propose actions to improve the quantity and quality of the graduate education in the area of mining industry, specifically of mining engineers, metallurgists, geologists, to satisfy the expectations of professionals in the mining industry. Included are an analysis of the present scenario and the future demands in countries like Chile and proposed plans for the Establishment of Educational Initiatives, country policies and market forecast, vis-a-vis the experience of Australia, South Africa, United Kingdom, Canada and the United States of America.

Jan 1, 2007

By Leiting Yue, Peng Ren, Yu Shen, Zhihong Liu, Haibao Shao, Longgong Xia, Feng Yu

The Kennecott-Outotec Flash Converting technology has been proven as an advanced and mature process in 5 individual plants during the past 2 decades. High grade copper matte (65–72%) produced in the flash smelting, or other smelting technologies is granulated to 3-5mm granules in a water torrent, and further crushed to fine powder (≈50µm) and dried to contain less than 0.3% H2O. Oxygen enriched air, together with fine copper matte powder and lime flux are injected into the reaction shaft by a matte burner. The copper making and slag making reactions will happen in very short time and distance during the particle falling and settling. However, industrial practice has found negative effects caused by sodium contamination. Na is introduced in the copper matte granulating process, and appears as Na2SO4 on particle surface. When Na content was high, scaling problems in the boiler will be worse, and the processing air will be blocked by the growing accretion around the matte burner, and as-produced blister copper is always high in S and O. In this present study, an industrial matte sample was used in the experimental work. Na was introduced into the matte powder by Na2SO4 solution soaking. The burning behaviour of the doped copper matte powder has been investigated as a function of the impurity concentration and processing temperature. Morphology and composition of these samples explained how Na2SO4 converts and reacts in the oxidizing atmosphere, and how they or their converting species influence the burning behaviour of matte particles. Cross-sections of as-prepared samples were analyzed with SEM-EDS, and the reaction mechanism has been carefully interpreted. Results from the present study can benefit both academic and industrial people. INTRODUCTION "Flash Converting" technology was developed jointly by Kennecott Utah Copper Smelter and Outotec (Finland) OY in 1992. The first industrialization of the technology was in Utah Smelter in 1995. Since 2006, it has been successfully applied in Xiangguang Copper, Tongling Jinguan Copper Branch, Fangchengang Jinchuan Copper, and Ningde Southeast Copper. The technology has also been further developed in those smelters. At present, roughly 2 million tons blister copper is produced annually through the Kennecott-Outotec Flash Converting technology, accounting for more than 10% of global primary copper production. The technology has advantages of high efficiency, high sulfur capture rate, good in environmental issues, mature equipment supporting, high automatic control level, low comprehensive energy consumption and flexible connection with the smelting unit, which make the technology to be one of the best choices in investing a new large-scale copper smelter or updating an old copper project in the world.

Jan 1, 2019

By C. S. Liao, S. L. Wang, C. H. Yan, F. X. Cheng

A significant development in the theory of countercurrent extraction will be presented in this article. A new term in countercurrent extraction process analysis, "Adjacent Stage Impurity Ratio" (ASIR), is proposed, and its expression is deduced. Furthermore, based on the term together with mass balance and extraction equilibrium, the conditions where a given countercurrent extraction separation operation can have minimum amounts of both extracting solvent and scrubbing agent solution can be estimated, and the equations of the two minimum amounts can be deduced. It was found that the equations for a two-component separation using a single aqueous or organic feed are exactly the same as they appeared in the theory initially established in the 1970s. Unlike its earlier version, the present derivation does not involve feed-stage-composition hypothesis, and also has the advantage of dealing with a double-feed system where both aqueous and organic feeds are simultaneously employed whereas the earlier theory can only analyze a separation using a single aqueous or organic feed.

Jan 1, 2014

By V. S. Papezik

Pyrophyllite, a hydrous aluminium silicate, is used mainly in the ceramic industry and to a lesser extent as a filler in the manufacture of paper, rubber, insecticides and baby powders. Commercial deposits of pyrophyllite in North America are restricted to the "Avalon Zone" , a belt of late Precambrian volcanic and sedimentary rocks that extends along the eastern flank of the Appalachian orogenic belt f rom Georgia to Newfoundland. The only commercial Canadian pyrophyllite deposit lies near Foxtrap on the A valon Peninsula of Newfoundland. Here, steeply dipping lenses of altered pyrophyllite rock occur in a north-trending rhyolite belt near the contact with a granitoid pluton. The altered rock is massive, light greenishyellow and contains varying proportions of pyrophyllite, sericite and quartz with lesser amounts of diaspore and traces of barite and rutile. A lteration was produced by acid solutions, either derived from or activated by the intruding pluton, at temperatures of 250° to 270°C and pressures not exceeding 2 kbr. The largest of the Foxtrap pyrophyllite lenses, discovered in 1897, was mined intermittently f rom 1903 until the early 1950s. The present owner of the mine, Newfoundland Minerals Limited, acquired the property in 1959 and ships between 27, 000 and 36,000 tonnes annually to th e company plant in Lansdale, Pennsylvania, for use in ceramic tile.

Jan 1, 1984

By Tatyana Alexandrova

The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Technological aspects of processing precious metal ores are examined in two respects: enhancing gold recovery from double refractory ores; and using carbonaceous ores on a production scale. The dispersed carbonaceous matter (DCM) present in concentrates causes the adsorption of [Au(CN)2]- complex on their surface during cyanidation process. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The possibility of rare metals recovery, including rhenium, from black-shale rocks, has been examined. Comparative assessment of analytical methods of rare metals detecting has been carried out. It has been proved that neutron activation analysis is a promising technique. It has been shown that colloid-salt fraction (nanofraction) with particle size less than 1000 nm makes up to 3 wt% of black shale samples and is extracted by water under special conditions. The use of water instead of chemically active reagents provides insolubility of the mineral matrix and fully reflects the colloid-salt element of the samples. To sum up, the justification of the choice of technology for processing of carbon-bearing ores is based on examining the type of carbonaceous matter and its adsorption behavior. When the content of carbon of high degree of metamorphism is considerable, it is possible to recover platinum group elements and rare elements from this type of ores. The obtained results predetermine the general guidelines for creating new methods and techniques of processing carbonaceous material for integral development of solid minerals in the mining and oilfield areas of Russia.

Jan 1, 2016