Search Documents

By A. Majumdar, B. Servière, H. Persson

The CCR refinery, which was built in 1931, treats both internal and third party copper anodes to produce 325,000 mt of copper as cathodes. These anodes contain high levels of impurities, such as Ni, As, Sb and Bi, that reports to the electrolyte during the refining step and need to be removed in order to maintain cathode quality and operating efficiencies. In the purification plant, the electrolyte is de-copperized via electrowinning in three stages. In the last stage, the copper content of the electrolyte is reduced to below 1 gpl in order to maximize the co-deposition of As, Sb and Bi with the Cu. This is accomplished with minimum arsine gas generation by using periodic reversal of the current and by controlling the final copper content of the electrolyte. Nevertheless, the possibility of exposure to arsine is treated as a major risk and controls have been implemented to reduce this risk. This paper describes the controls in place at the purification plant, which are being continuously improved through periodic risk assessments and audits. INTRODUCTION The CCR Refinery, which is a part of Glencore Canada Corporation and located in Montreal-East, Quebec, is a custom copper and precious metal refinery, with a capacity to refine 325,000 tonnes of copper anodes per year. Copper anodes are received from the Horne smelter in Rouyn-Noranda, Quebec, Altonorte smelter in Chile and other 3rd party smelters. CCR anodes are produced using the spent anodes from the tankhouse along with purchased spent anodes and copper scrap. The precious metal plant treats the tankhouse anode slime, purchased anode slime, precious metal ingots and Doré anodes from Glencore’s Brunswick lead smelter in Belledune, New Brunswick. CCR products include copper cathodes, silver and gold bullion, a platinum-palladium concentrate, selenium, tellurium dioxide and nickel sulfate. In 1975 an accident occurred at CCR where two employees were exposed to fatal levels of arsine emitted from the then existing purification cells. This process was therefore shut down immediately. Research and development work was then initiated to determine the optimum electrowinning conditions whereby arsine gas generation would be minimized while maintaining high copper and impurity removal efficiencies. It was found that the application of periodic reversal of current (PRC) during the last stage of electrowinning retarded the onset of arsine formation while at the same time allowing the copper concentration to be reduced to less than 1 gpl (Houlachi & Claessens, 1978). A new purification plant was designed based on the PRC technology and was started up in 1976. In addition to the use of PRC electrowinning, the new plant is located in a fully enclosed section of the tankhouse. A special effort was made to design a ventilation system to evacuate the acid mist in addition to any arsine gas. Arsine monitors were installed to measure the emissions from the stack along with arsine levels in the workroom. The arsine monitors and the ventilation system were interlocked with the rectifiers (Thiriar et al., 1983).

Jan 1, 2019

By A. Scheltema Beduin, H. Oterdoom, A. Haaks, C. Kempe, A. Liedtke

The bath level measurement is applied in many furnaces to keep control of the level of slag and metal or matte inside. The BLM is used mainly in bath processes, and has not seen much evolution in its basic functionality. For a closed DC FeCr furnace, special demands based on the furnace design and extreme process conditions were considered for the design of a bath level measurement in order to collect valuable information about the furnace operation. This paper will describe these demands and the solutions for them, followed by some of the uses for the BLM in a closed FeCr furnace. Some of the future developments on the BLM conclude this presentation.

Jan 1, 2015

By D. F. Sangster, P. J. Hood, G. A. Gross

"Some results are presented of an integrated geological and geophysical study of Precambrian magnetite-quartz iron-formation in the Kapiko Iron Range north of Nakina, Ontario. Detailed geological and topographical mapping was carried out in conjunction with detailed geophysical investigations such as vertical magnetic field, vertical magnetic gradient, hammer seismic, horizontal-loop electromagnetic and magnetic susceptibility surveys. In addition, oriented drill cores were obtained for magnetic polarization studies.Vertical-force magnetic anomalies within individual rock units showed a strong positive correlation with topographic relief. Moreover, magnetic intensity was found not to be quantitatively proportional to the magnetite content in the rocks, due to the presence of high remanent magnetization of the magnetite. Also, the remanent polarization direction was sub parallel to the plunge of the fold structure and mineral lineation in associated rocks.Vertical magnetic gradient measurements were found to be more accurate in locating buried contacts between magnetite-quartz iron-formation and country rock than the vertical magnetic force data.An in-situ magnetic susceptibility meter was used to measure the magnetite content of iron-formation, and the measurements were subsequently compared with vertical-force magnetic results.The results of the EM survey were inconclusive; some magnetite-rich zones produced anomalies in the out-of-phase component. whereas others did not. The reasons for such inconsistencies are not yet apparent.Longitudinal seismic wave velocities measured parallel to the bedding in magnetite-quartz iron-formation ranged from 10,600 ft/sec. to 14,500 ft/sec. The seismic velocity appears to increase with an increase in deformation of the rocks."

Jan 1, 1966

By S. Kodama, G. Sasaki, K. Matsugi, K. Sugio, Y. B. Choi

"Pure aluminum (Al) matrix composites with changing the volume fraction of TiB2 particle content from 10 to 30% was fabricated by spark plasma sintering (SPS) process. Then the microstructure, density, dispersibility and thermal conductivity of the composites was estimated. As increasing TiB2 content, the dispersibility of particles and the density of the composites degraded slightly. And, the effect of the dispersibility of TiB2 particles on the thermal conductivity was quite little. The thermal conductivity of the composites was less than the theoretical value calculated by Maxwell-Eucken equation considering the effect of the density. It is due the influence of the interface heat transfer rate, because these composites have many small sized particles and have high interface density.INTRODUCTION Recently, metal matrix composites (MMCs) have been used widely in electric / electronic components, architectural materials, transportation equipment, aerospace and a precision instruments, because it’s superior properties have been greatly watched. Demand of MMC for industrial use has been increasing gradually. Furthermore, multifunction properties are required for the composites strongly. By integrating the dissimilar materials, the composites have various properties that we cannot get from monolithic materials. On the other hand, the response to the thermal management is required for materials, recently, and the need for the structural material controlling the thermal conductivity has been increasing. Especially, superior thermal conductivity and good mechanical properties from room temperature to high temperature are required for heat sink and heat exchanger at the same time. In late years, a study on the composites combining carbon materials and aluminum and copper has been developing, and actually the composites with high thermal conductivity which is not provided in the conventional materials is developed. On the other hand, non-oxide ceramics particles such as SiC and AlN, TiB2 have good thermal conductivity. Particularly, as TiB2 has good electrical conductivity, TiB2 containing MMCs is expected as innovative materials used as electric/ electronic components. Furthermore, as TiB2 has low density, high melting point, low thermal expansion and good deformation resistance, the development of high performance composites with multi-functional properties is expected. As thermal conductivity of pure Al and TiB2 are 225 and 66.4 W/mK, respectively, it is expected that the degradation of thermal conductivity by adding dispersant in Al matrix is suppressed. The authors have carried out a thermal conductivity, electrical conductivity, mechanical properties of 20 vol.% TiB2 dispersed Al composites (Sugio, 2016, Sasaki, 2016). In this study, the influence of quantity of addition of TiB2 on microstructure, thermal conductivity was studied minutely."

Jan 1, 2018

By Q. Li, X. -L. Lei

Accompanying global energy shortage and high energy prices, shale gas has been the focus of exploration and it has attracted great attention from both academia and industry. The combination of horizontal drilling and hydraulic fracturing enables the extraction of huge quantities of shale gas from impermeable shale formations. During the process of hydraulic fracturing, great amounts of water, sand and chemicals must be injected into the shale formation at a high pressure, which may trigger seismicity. Such events could occur due to the presence of faults or the reactivation of these potential faults. Shale is the main component of source rock in the Sichuan Basin, China, and has the greatest contribution to the natural gas of the basin. In order to investigate the fracturing mechanism of shale in the Sichuan Basin, China, a series of rock fracture tests under triaxial compression were carried out in the laboratory in order to investigate the hydraulic fracturing behavior in relation to the seismicity. Based on the high multichannel waveform recording system, the detailed spatio-temporal distribution of acoustic emission due to micro-cracking was used to examine the deformation and fracture behavior of shale. In addition, the effects of confining pressure on the deformation and fracture in shale under triaxial compression by acoustic emission monitoring and X-ray computed tomography were discussed in the paper. The experimental results indicate that the shale samples demonstrate brittle fracture behavior. The confining pressure has a great effect on the complexity of the fracture planes and the spatial distribution of acoustic emissions, but few contributions to the location of the major hydraulic fracturing plane. The foliation of shale plays a dominant role in the rupture process and the geometry of the major hydraulic fracturing plane. The high confining pressure increases the strength and restrains the deformation of shale during compression process. These results shed some light on the understanding of onset of hydraulic fracture initiation not only for shale gas exploration and production, but also for CO2 geological storage and underground energy storage.

Jan 1, 2015

By A. Eslami, H. Tabatabaei, M. Kolandoozan, Z. Manafi, A. R. Shahverdi, M. Noaparast, M. Oliazadeh

Application of Acidithiobacillus ferrooxidans bacteria to flotation of Sarcheshmeh low-grade copper sulphide ore was studied. Sarcheshmeh low-grade ore contains pyrite, which causes some problems in the flotation of copper minerals. In this study, A. ferrooxidans was used to change the surface chemistry of pyrite and copper sulphide ores and consequently, their flotation behaviour. In the presence of A. ferrooxidans and xanthate as a collector, pyrite was depressed whereas chalcopyrite and other sulphide minerals were unaffected. In addition, the pulp pH remained unchanged. It was shown that the surface chemical properties of the bacteria can be manipulated successfully to achieve the desired effects in a flotation process. The results showed that the recovery of pyrite in the presence of the bio-depressant is 50% lower than when no bacteria were present. At the same time the recovery of chalcopyrite remained unchanged.

Jan 1, 2004

By M. K. Walter

"The underground operations of Kidd Creek Mines uses an average of 450 U.S. gpm water during regular operations, and discharges an average of 800 U.S. gpm through consecutive staged pumping lifts of 1200f t.Water is used as a flushing medium for the drilling operations and as a dust suppressant for drawpoint mucking. The water retains an average of 5% suspended solids by weight which is removed underground before being pumped to the surface. This paper outlines the treatment of the mine water for the removal of suspended solids which are chemically treated to settle out as a sludge product of 60% solids by weight. This process reduces the sludge handling operation by 50%. The sludge is systematically disposed into the ore passes.IntroductionThe Kidd Creek minesite, located 27 km north of Timmins, Ontario, produces 4.5 million tonne s of copper, lead, zinc and silver ores annually from its No. I and No.2 underground mining operations. Both mines use a sublevel blasthole stoping method of extraction.Water from the underground operation passes through a series of surface settling ponds, where it is treated to remove heavy metal ions from solution. A blend of the pond effluent with fresh water from Kidd Creek, supply the underground with water at an average rate of 450 U.S. gpm. Water flows from the production zones through coarse sumps and into a main pumping station. There are five main pumping stations underground, three in No. I Mine and two in the No.2 Mine.The No. 2 Mine pumping stations are located on the 4800 level and the 3600 level. All water below the 3600 level to the shaft bottom is controlled from the 4800 pumping station. The water from the 4800 pumping section is combined with water from the remaining levels of the No.2 Mine at the 3600 pumping station. Water from the 3600 pumping station is pumped to the 2400 pumping station in No. I Mine.The No. I Mine pumping stations are located on 2800, 2400, and 1200 levels. All water below the 2400 level to the shaft bottom is controlled through the 2800 pumping station. This water is pumped to the 2400 pumping station. The 2400 pumping station also controls the water below 1600level to 2400 level."

Jan 1, 1988

By Eamonn F. Maher

Superconductivity is one of the most remarkable scientific phenomena ever investigated. It is the phenomenon whereby some materials exhibit zero resistance to the passage of an electric current when cooled to low temperatures, and requires a quantum mechanical explanation. Four Nobel prizes in physics have been awarded specifically on the subject of superconductivity, with many more enabled by superconducting technology. For example, particle beams are generated in accelerators and manipulated in ?particle beam lines? in the ?Big Physics? projects around the world eg. at CERN, Geneva, leading to major discoveries in fundamental particle physics. Similarly, at the JET Propulsion laboratory near Oxford, U.K, controlled nuclear fusion has been demonstrated, and magnetic containment of plasmas is key. In the chemical and biological sciences high field NMR spectroscopy has become indispensable for examining organic matter, revealing the mysteries of the workings of cells, genetics, and in the development of new polymers and pharmaceuticals. With all these very advanced uses for superconducting magnets, it is easy to forget that superconductivity is big business, not just a scientific curiosity. MRI (Magnetic Resonance Imaging) superconducting magnets, the key component of high resolution body scanners, use approximately half of the world?s superconducting wire ? the other half being mostly used in accelerator magnets. The MRI market is about 3 billion dollars per annum, and one MRI magnet uses 200km of wire. New applications for superconducting magnets are now appearing including ?Catheter steering?, enabling much shorter timescales for life-saving brain tumour removals and ?Functional MRI?, a whole new area in patient diagnostics. Whilst the use of low temperature superconductors (LTS) is now well established commercially in superconducting magnets and niche electronic applications, the application of LTS in electric power distribution and transport has been very limited to date. It is now more than fifteen years since the so-called High Temperature Superconductor (HTS) materials were discovered: these can be operated at liquid nitrogen temperatures rather than liquid helium temperatures. However, materials processing and scale-up issues have prevented their widespread use, and in particular the required price/performance criteria are only beginning to be reached except in certain niche markets. BSCCO (Bismuth Strontium Calcium Copper Oxide) tapes up to one km long are now readily available, and have been demonstrated in high current cables for power distribution networks, but the general consensus is that 1) it is difficult to reduce the price much further because of the silver matrix required and 2) in applications where coils are required eg. motors, generators, transformers etc the properties of BSCCO are rather poor because of the critical current dependence on magnetic field. Magnetic fields are always associated with coils and windings, and such fields are of course fundamental to the operation of all electrical machines. YBCO (Yttrium Barium Copper Oxide) however, has good characteristics in field and for the last few years there has been intensive research and development costing several tens of millions of dollars worldwide into the scale-up of production of so-called ?coated conductor?. This ?second generation? tape can be produced by any of many different film deposition techniques, with more or less success for short lengths, but as yet it is unavailable in lengths more than a few tens of metres.

Oct 1, 2003

"The main purpose of geometallurgy is to develop a model to predict the variability in the mineral processing performance within the ore body. Geometallurgical tests used for developing such a model need to be fast, practical and inexpensive and include as an input data relevant and measureable geological parameters like elemental grades, mineral grades and grain size. Important in each geometallurgical program is to define the number of samples needed to be sent for geometallurgical testing to enable reliable metallurgical forecast. This is, however, a complicated question that does not have a generic answer.To study the question on sampling a simulation environment was built including a synthetic ore body and sampling & assaying module. A synthetic Kiruna type iron oxide - apatite deposit was established based on case studies of Malmberget ore. The synthetic ore body includes alike variability in rock types, modal mineralogy, chemical composition, density and mineral textures as its real life counterpart. The synthetic ore body was virtually sampled with different sampling densities for a Davis tube testing, a geometallurgical test characterising response in magnetic separation. Based on the test results a forecast for the processing of the whole ore body was created. The forecasted parameters included concentrate tonnages, iron recovery and concentrate quality in terms of iron, phosphorous and silica contents.The study shows that the number of samples required for forecasting different geometallurgical parameters varies. Reliable estimates on iron recovery and concentrate mass pull can be made with about 5-10 representative samples by geometallurgical ore type. However, when the concentrate quality in terms of impurities needs to be forecasted, the sample number is more than 20 times higher. This is due to variation in mineral liberation and shows the importance of developing techniques to collect qualitative information on mineral and ore textures in geometallurgy."

Jan 1, 2016

By R. R. Stone

"This paper will examine the role of debt and equity in project financing and will illustrate the impact on the return to the project sponsor of each type. Conventional debt sources will be examined, as will product purchaser advances, foreign export-import bank loans and lease financing. The paper will review guarantees, charges against the project, dividend restrictions and other commitments. It will also discuss various features of sales contracts and the degree to which they can assist in securing financing. IntroductionThe cost of bringing new mining projects on stream is escalating significantly more rapidly than general rates of inflation. Reasons for this include the higher costs of safeguarding the environment and ensuring the health and safety of workers. The need to develop properties in more remote areas is also a significant factor. These higher costs have not been matched by increases in metal prices, making the task of financing these projects ever more difficult. At the same time, the imagination of borrowers and lenders seems boundless, and innovative schemes for financing projects are constantly being unveiled.It is probably safe to say that no two projects have ever been financed in precisely the same way and the number of financing options for any project is limited only by the imagination of the sponsors themselves. The objectives of the project sponsor represent the most important factor in determining the scope of possible financial arrangements. For example, the sponsor may wish to maximize over-all company leverage by isolating each of its projects in separate companies. In so doing, it hopes to facilitate more ventures than would otherwise be the case. These objectives point toward true project financing. Additional objectives may be to develop a number of its properties by joint venture and to reduce the amount of debt on the sponsor's balance sheet. Those sponsors whose objectives include minimizing over-all financing costs will wish to increase the number of financial options and, as a result, will not be so concerned with effecting true project financing. This approach may also provide ""greater certainty that tax benefits are utilized quickly."

Jan 1, 1980

By P. K. Kaiser

3-D virtual reality (VR) visualization has opened new opportunities for complex 3D (x, y, z), 4D (x, y, z, t) or even nD data interpretation. The integration of common earth models (3D geologic data), mine models (3D excavations and stress), extraction models (1D time sequencing or mine sequencing) and nD monitoring data (e.g., seismic event parameters) into a common mining process model provides a platform for experts in various fields to better design, evaluate, monitor and modify mine plans throughout a mine?s life; from feasibility, through operation, to closure. Viewing seismic data in a stereoscopic VR environment within a mining process model offers data interpretation processes previously unavailable at lower dimensionality. MIRARCO has developed data analysis and viewing processes specifically designed to enhance microseismic and seismic data interpretation in a collaborative, immersive VR environment; bringing mine personnel and expert consultants together to evaluate data and make strategic decisions for cost effective and safe mining. Seismic events cause immediate hazards (rockbursts) and microseismicity causes gradual hazards through its cumulative effect in rockmass degradation. The focus of this paper is on understanding seismicity from a mine safety and mine planning perspective; in particular, how seismic migration patterns relate to the rockmass response to mining. The benefits of innovation in seismic data interpretation are significant, e.g., for hazardous work area identification, allowing better formulation of re-entry policies and workforce allocation planning, as well as allocation of effective support systems to strategic areas of elevated risk. Better understanding of the overall response of a mine to extraction also facilitates mine planning and design, assisting in reducing production costs and thus in enhancing profitability.

Apr 1, 2005

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, N. Andrade

In this work, the age-hardening behavior of cast Al-Si base alloys was investigated. It was found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu-Mg alloys. TEM observations reveal that the age-hardening behavior is related to the precipitation sequence of the alloy. For the Al-Si-Cu-Mg alloy, the first aging peak is the result from the high-density GP zones, while the subsequent are from metastable phases. The transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks.

Jan 1, 2006

By Robert B. Parsons

"While it might seem like heresy to suggest that ""taxation"" can be a source of financing, never the less some generous tax rules can considerably enhance the tax savings pertaining to a particular expenditure or project. A basic tax knowledge, and careful tax planning, can optimize government participation in a project. INTRODUCTIONIn trying to identify sources of financing for a project, ""government"" as a source of funding is normally thought of in terms of government grants, loan guarantees, interest rate buy downs, property tax waivers, hydro subsidies, and so on. Generally, such concessions are somewhat difficult to obtain, especially in the current period of apparent fiscal restraint. One source of government funding which should not be overlooked is the income tax regime, and, at the provincial level, the various provincial mining tax regimes.While the taxpayer would not normally view a tax system as a potential source of government financing, nevertheless various federal and provincial rules applicable to the mining industry can offer attractive tax deductions - and tax savings - with respect to particular expenditures. In fact, it is not unusual for a civil servant to refer to a tax deduction as a tax ""subsidy"". For example, in the right circumstances, the cost of a smelter expansion in New Brunswick would cost the operator only 31 cents on the dollar, with the federal and provincial governments paying for the other 69 cents by foregoing tax revenues (Table I). In a sense, such tax savings could be compared to a government grant equal to 69% of project costs. Of course, not every project expenditure will generate that degree of government funding. The fact of the matter is that the percentages of tax savings attached to different expenditures cover a wide range, depending on a complex mix of factors. The point to understand is that the tax rules can offer some valuable savings, even after tax reform, and that a basic knowledge of the tax rules can yield some fruitful rewards."

Jan 1, 1989

By P. W. Percival, J. J. Janssens

"Whitehorse Copper is a 2600-ton-per-day underground copper mine located within the city limits of Whitehorse, Yukon . In early 1978, due to increasingly difficult ground conditions. it was decided to investigate the conversion from longhole open stoping to vertical crater retreat mining. On-site crater testing by C-I-L demonstrated the feasibility of V.C.R. mining at Whitehorse Copper.After some investigation. a down-the-hole drilling rig was chosen and drilling began in November /978. Blasting began in June /979. and to September 1980 approximately one million tons of ore had been blasted. In-field changes to both drilling and blasting techniques have been implemented. Some of these changes were dictated by problems encountered; others were made to improve efficiencies.To date. V.C.R. mining has proven successful from a drilling and blasting aspect.IntroductionWhitehorse Copper Mines Ltd ., a division of Hudson Bay Mining and Smelting Co., Limited , is a 2600-Lp.d. underground copper mine. The plant site is located I mile west of the Alaska Highway, and approximately 7 miles south of Whitehorse city center. Production is from the Little Chief orebody, and total output is from vertical crater retreat stopes.The Little Chief and Middle Chief orebodies at Whitehorse Copper had original reserves in excess of 6 million tons, most of which graded 2.00/0 copper or higher . The orebodies are typical skarn deposits that have developed along the contact between an intrusive diorite and a limestone-quartzite flank pendant. The limestone has been metasomatized to form a calcium-magnesium skarn which, along the limestone / quartzite contact, has locally further developed into a mineralized magnetite-serpentine skarn. The principal copper minerals are bornite and chalcopyrite, with minor chalcocite and valleriite. Skarn gangue minerals are serpentine, diopside, garnet, epidote, calcite and wollastonite. Appreciable values in gold with some silver are present and recovered as well."

Jan 1, 1981

Train on Different Equipment - * Immersive?s interchangeable cabin controls technology - ?clip on & off? * Change Simulator from one machine to another in minutes * No technical expertise required to swap * Real, functioning, controls and displays are used to aid rapid learning Immersive has produced a range of Conversion Kits to suit most equipment. Modular design - Easy to convert from one machine model to another with a Conversion Kit. Caterpillar Models Trucks - 769D, 773D, 777D Trucks - 785B, 789B, 793B Trucks - 785C, 789C, 793C, 797 Excavator/Shovel - 5130, 5230 Front end loader ? 992, 994 Dozer ? D10, D11 Komatsu Models Trucks - HD325, 785-5, 985-5 Trucks - 730E, 830E, 930E Dozers - D375A-3, D475A-3 Shovel - PC8000 P&H Shovels - 4100A, 4100XPB, 4100BOSS Hitachi Shovels - EX2500, EX5500 O&K Shovel - RH200 Bell Articulated Truck - B40C

May 1, 2003

By R. L. Christie

"THE ISLANDS lying north of the Canadian mainland, and the large Boothia and Melville peninsulas, form one of the great archipelagos of the world; this sparsely vegetated and nearly unpeopled region extends about 1,500 miles east to west and 1,200 miles from the mainland to the northern tip of the northern-most island. Sea access to most of the islands is restricted by ice to the summer season, and the 'polar pack' ice of the Arctic Ocean presses the year round against the northwest margin of the archipelago. Although the region is remote, the accessibility has greatly increased through a network of weather stations, airfields and air routes connecting with southern centres.The area considered in this paper is that part of the island region underlain mainly by sedimentary rocks. In broad terms, this includes the land and sea areas of the archipelago and the adjacent continental shelf, but excludes the dominantly 'Shield' terrain of Baffin Island, and of Melville and Boothia peninsulas. An impression of the size and potential of this sedimentary region may be gained by comparing some areas: the land area of islands underlain mainly by sedimentary rocks is over 300,000 square miles or about 50,000 square miles greater than the area of Alberta. The total area of the region, including the continental shelf and the inter-island areas, may be double this figure, and may approximate one-seventh of the land area of Canada."

Jan 1, 1970

By H. D. S. Miller

"Artificial stope support has become an essential component of many underground mining operations. Because the use of cable bolts in open stopes is a relatively new concept, most support is still designed by trial and error or by rules of thumb. This often results in costly overdesigned support or inadequate support which leads to stope failure.This paper proposes guidelines to determine support requirements using the stability graph method. The stability graph method is an empirical open stope design technique that takes into account the key factors that influence stope stability. The factors for the design of a cable bolt support system include bolt length, bolt intensity and the original rock mass competency and can be estimated using empirically calibrated charts. The empirical charts were developed based on more than 60 case histories of cable bolting success and failure in Canadian open Slope mines.The concept of pre reinforcement and supp ort stiffness will also be discussed.INTRODUCTIONArtificial support, in the form of rock anchors, has become an important component of all underground mining operations because its stabilizing effect contributes to make underground workings safer. There are several types of rock anchors featuring different properties and having a variety of functions. This paper focusses on grouted cable bolt applications in large open stope mining. Such a support system may improve the competency of the disturbed rock mass to a point approaching the undisturbed rock quality by limiting joint movement and dilation. This results in more stable, possibly larger and, thus, more efficient production stopes."

Jan 1, 1989

By Alfredo Bambaren

First Encounters between Communities and Mining 1. Importance, meaning and process 2. Antamina?s study case 3. ?Self-organization? theory (NLP) 4. The story we tell, the values we live 1. Importance, Meaning and Process ? First encounter stays in mind as a model. ? First encounter means foundation. ? First encounter builds the story.

May 1, 2010

By Malcolm Scobie

"This paper reviews the evolution of Canadian surface and underground mining automation, principally relating to: advances in communications, initial development of machine teleoperation from line-of-sight remote control, and islands of automation. The eventual role of teleroboties and minewide robotic mining remains to be resolved. The progress and approaches adopted have tended to vary within each sector of the mining industry. Recent information technology advances have made possible the Digital Mine; in which information associated with all mining processes, however dispersed, would be integrated with support systems using new communications technology. The Digital Mine will provide the information infrastructure to serve as the foundation for minewide automation. This paper concludes by reviewing the issues likely to govern implementation success, relating to: mining process design, machine design, machine intelligence, and mine planning and control.IntroductionSignificant advances have recently been made in underground hardrock mine communications and teleoperation. Subsequent R&D efforts are mainly focussing on control systems for various types of machines. In underground potash mining, the realization of automated continuous mining systems appears to be imminent. Recent advances in surface mine dispatching, machine monitoring and global positioning systems (GPS) have tended to reactivate some of the initial R&D enthusiasm developed in the '70s for surface mine automation. Mines at large are approaching a major milestone: the implementation of comprehensive communications infrastructure which proves to be sufficiently reliable and economical to support the automation of routine mine production, either using teleoperated or autonomous machines. This then should motivate a deeper commitment to real time monitoring and management. The communications advances make possible the Digital Mine; in which information associated with all mining processes, however dispersed, would be integrated with support systems using information engineering. The Digital Mine will provide the information infrastructure to serve as the likely foundation for a wide range of automation scenarios. This paper surveys the status and directions of automation development in both surface and underground Canadian mines, pointing to what are seen to represent key technology development issues."

Jan 1, 1995

By E. L. Bruce

EUROPEAN Russia is mainly a great plain, the average elevation of which is only 600 feet above sea level and the maximum elevation less than 1,200 feet (Figure 1). The main divide between the Arctic ocean and the Black sea and Caspian sea is an indistinguishable topographic feature from which the Dneiper and Don rivers flow southward to the Black sea and the Volga river to the Caspian. The valleys of these rivers are but little below the general level (Figure 2). To the south, this great, rolling plain is broken by a low ridge of Precambrian gneisses and intrusive rocks. The Crimea is an upland from which the descent to the Black Sea coast is precipitous (Figure 3). The Ukrainian Soviet Socialist Republic occupies the southern part of the plain. It is the southwestern unit of the Union, bordered by Rumania and Poland on the west and by the Crimean Soviet Socialist Republic on the south.

Jan 1, 1938