Search Documents

By Robert M. Hopkins, Craig C. Monahan

A corrosion survey was performed on ten selected H-piles which support a reinforced concrete wharf located at Trepassey, Newfoundland. Approximately 900 thickness measurements were taken at twelve different locations in each off our zones on the steel piles: the splash (atmospheric) zone, the intertidal zone, the low tide zone and the submerged zone. Results show that over the 2o-year life of the wharf, corrosion has been most severe in the splash, low tide and submerged zones with average corrosion rates for the flanges of 6.95, 9.45 and 6.86 mils per year (mpy}, respectively, and average corrosion rates for the webs of 5.13, 4.12 and 3.45 mpy, respectively. Minimal attack was found in the intertidal zone where the average corrosion rate was only 1.66 mpy on the flanges and 1.37 mpy on the webs. Such a pattern of attack is frequently observed f or steel piles partly submerged in seawater. The abnormally low corrosion rate associated with the intertidal zone is generally explained as being due to cathodic protection induced by the high corrosion rate in the adjacent low tide zone. Analysis of the corrosion data obtained for the Trepassey wharf would suggest that this explanation might be incorrect. An alternate hypothesis has been brought forward which better accounts for the extremely low corrosion rate observed in the intertidal zones of these piles.

Jan 1, 1990

By Si Qin

Unknown goafs and roadways of abandoned coalmines can be a great water inrush hazard for coalmine workers. Consequently, advance detection of such hazards is of great importance. By detonating seismic charges in underground coal seams, we can collect seismic data using a surface survey line, which is located across the ground projection of the underground shot point. This experiment was conducted in a coalmine in Shaanxi Province, China. After surface elevation compensation and travel time adjustments, we accurately determined the position of the goaf boundary along the survey line based on the wave velocity anomaly on the seismic record. Then we used a scattered wave imaging technique to enhance the energy of the scattered waves that are generated when the coal seam roof slide wave (refracted wave when the incident angle bigger than the critical angle) hits the roadway, thus confirming location of a geological discontinuity (roadway). This experiment shows that the coalmine ground seismic method, employing an underground explosive charge and a surface seismic array, has the ability to detect an abandoned roadway and goaf in advance of coal mining, thus can improve worker safety.

Aug 1, 2013

By L. M. Cumming

"The contact between dolomite of the St. George formation (Cambro-Ordovician) and limestone of the overlying Table Head formation (Middle Ordovician) is a regional disconformity. This is best illustrated from exposures on Pointe Riche Peninsula, near Table Point, and along Port au Port Bay. The contact occurs along 180 miles of the west coast of Newfoundland from St. John Island in the north to the western part of Port au Port Peninsula in the south. A disconformity of the same age occurs between the Romaine and Mingan formations on the north side of the Gulf of St. Lawrence.Dolomitic beds beneath the disconformity locally contain concentrations of base-metal sulphides. Sphalerite occurs in dolomite pseudobreccias of the St. George formation at Zinc Lake, 7 miles northeast of Daniels Harbour. The 'Western Newfoundland Lower-Middle Ordovician regional disconformity is interpreted as having originated on and near the edge of a broad platform, and to have provided an important regional geological control in the localization of zinc mineralization."

Jan 1, 1968

By K. B. Chaudhuri, I. D. Webb, F. E. Rachor, F. A. Sauert

"A characteristic of all methods of copper concentrate smelting is that slags with a high copper content are produced at some phase of the operation. Recirculation to the smelting unit, electric furnace reduction or flotation are at present used on an industrial scale to recover the copper from these slags. This paper describes the application of the top-blowing technique, originally developed by KHD Humboldt- Wedag AG for refining of metallic copper, for the treatment of copper-containing slags. By this method, a mixture of a reducing gas and commercial oxygen is blown onto the melt at velocities which can be supersonic from the tip of a water cooled lance. The impingement of the reaction gas mixture on the surface of the slag forms a depression in the molten phase and a deflection of the jet which brings the slag into a rotating motion. This causes high rates of heat and mass transfer. Results of pilot-plant tests for batch and continuous treatment of slags are presented, and the potential applications of top blowing for industrial-scale operation are indicated. In combination with the cyclone as a smelting unit, this process appears to be economic for smelters of very low capacity."

Jan 1, 1980

By D. Mills, W. H. S. Lawson

"The need to make repairs is seldom a major consideration in the design, fabrication and installation of major components of electrical generation plants. Repair welding, however, is a fact of life in the electrical generation industry, for restoration of degradation in service, from cavitation of hydraulic turbine runners, to corrosion and fatigue damage in pressure vessels. In making weld repairs to carbon and low-alloy steels, the largest source of trouble is hydrogen embrittlement and related post-weld cracking. Various strategies have been developed to control problems from this source, including post-weld heat treatment, the use of nickel-base alloy filler metals and the temper bead welding technique. Each of these basic strategies is being applied as circumstances require; each strategy must, however, be implemented in a manner that reconciles weldment structure and hardness, degree of restraint and service environment with the consequences of unsatisfactory performance of the repaired component.IntroductionMajor working components of electric generating plants are specified and installed on the basis that, wherever technically and economically feasible, they will retain functional capacity without major repairs for the twenty-five-plus years of normal plant lifetime. Nevertheless, repairs are often required, and welding is usually an essential feature of the work. Remedial welding may be performed to correct design or fabrication errors which become evident only at the time of component installation. The most common causes of requirements for repair involve corrosion, fatigue or related processes which prove more aggressive than expected during service. Increasingly, our planning for future repair requirements is related to continual improvements which are occurring in nondestructive evaluation technology. As components are periodically reinspected during their service life, fabrication induced defects may be revealed for the first time quite late in the life of the component. When this occurs, repair must be considered wherever inaccessibility of a flaw makes it impossible to prove its inactivity. Finally, there are certain components, for instance in hydraulic turbines, which cannot be economically made or used without the expectation of service induced wear. Here, periodic maintenance welding must be regarded as a normal event."

Jan 1, 1981

This paper discusses three case studies conducted at Highland Valley Copper mine (HVC) that illustrate operational improvements and insights which resulted from using the McGill University gas dispersion sensors. In the first study, the superficial gas velocity (Jg) sensor was used to implement a gas profiling control strategy for the rougher, scavenger and first cleaner cells in the Cu/Mo separation circuit. The data showed a 40% reduction of down-the-bank Cu recovery at constant Mo recovery which resulted from operating the cells at the target profiles. In the second study, the bubble size analyzer was used to better understand two mechanisms of bubble formation in the two flotation columns that make up the final Mo cleaning stage: the conventional rubber-sleeve sparger and the Microcel(TM) system. The data showed a considerable reduction of bubble size in the Microcel column which resulted in a significant increase in concentrate quality (1-2% Mo absolute) and a dramatic (4-5 fold) increase in concentrate production rate compared to the typical operation. The estimated economic benefit resulting from the improved column flotation operation was an overall 4% increase in Mo circuit recovery. In the third study, real-time measurements obtained from the gas holdup and bulk density sensors were used to infer the pulp density (% solids) in a rougher cell of the bulk flotation circuit. Validation tests demonstrated that this approach provides reliable pulp density measurements. Although promising, more work is required before implementing this approach at HVC.

Jan 1, 2009

By Cheryl Devine, Radhakrishnan Mahadevan, Vladimiros G. Papangelakis, Srinath Garg

The microbial-mediated recovery of valuable metals locked in mining wastes presents an economical alternative to conventional hydrometallurgical processes. The present study investigated the bioleaching response of a low-grade nickeliferous pyrrhotite tailings (0.6 wt% Ni) and an upgraded pyrrhotite tailings (1 wt% Ni) produced by Vale Base Metals in the Sudbury Basin of Ontario, with the ultimate aim of maximizing Ni recovery. The initial part of the study focused on the bacterial adaptive evolution protocol, by repeatedly sub-culturing an indigenous culture from an acid mine drainage site on 2% (w/v) pyrrhotite tailings. The results showed that the extent of Ni dissolution is positively correlated with microbial activity. Microbial profiling revealed A. ferroxidans to be the dominant member of the microbial consortium. The enriched culture was used for optimizing the growth medium by varying the concentration of essential growth nutrients. Finally, an aerated biotic and abiotic leach of a 10% (w/v) upgraded pyrrhotite tailings with and without pH control, showed a higher recovery of Ni in the pH controlled experiments. These results demonstrate that a high concentration of the oxidant Fe3+ in solution promotes the dissolution of Ni. Furthermore, the sulphide conversion into So was found to be higher in the pH controlled experiments (32%), relative to the experiment without pH control (10%).

Jan 1, 2015

By Robert B. Parsons

"There is a widespread concern that certain of Finance Minister Michael Wilson's Tax Reform proposals will likely lead to a significant decline in flow through funding after 1988. This does not bode well for the junior exploration sector, which relies heavily on flow-through to finance exploration programs. The exploration industry is actively pursuing various solutions to the problems posed by Tax Reform, in order to ensure that flow-through has a future.IntroductionWhile the proposals contained in Finance Minister Michael Wilson's Tax Reform White Paper may not be as far-reaching as some people had expected, nevertheless the combination of the existing tax rules and proposed new rules offers sufficient complexity to keep pencils sharpened for many months. After having had an opportunity to study Tax Reform since June 18, 1987, the sharpened pencils are suggesting that the White Paper is not without its shortcomings and pitfalls. Insofar as the mineral exploration industry is affected, there is widespread concern that adoption of certain Tax Reform proposals could spell near disaster for mineral exploration in Canada. More specifically, there seems to be a consensus among the industry, as well as some federal and provincial government officials, that the announced phase-out of the ""mining exploration depletion allowance"" (MEDA) would reduce the appeal of flow-through shares to the point where only a fraction of exploration funding would be financed in the future by flow-through."

Jan 1, 1987

By R. G. Gillies, C. A. Shook, W. H. W. Husband

"The current state of knowledge concerning pipeline transport of coal in water slurry form is summarized for the four categories: coal-water fuels, conventional fine coal slurries, coarse coals and stabilized mixtures of coarse and fine particles. Surface chemistry is of dominant importance for coal-water fuels and considerable progress in understanding the role of surfactants has been achieved in recent years. Little generalized research on the flow of conventional fine coal slurries has been done in the past 17years, although innumerable conceptual designs and feasibility studies have been undertaken. Coarse coal slurries are fairly well understood but the model which explains their flow requires more data to be established fully. Stabilized flow mixtures should probably obey the same model as coarse coal slurries but experimental results for stabilized mixtures have not yet been incorporated in a comprehensive theory.IntroductionPipeline transportation of coal in a water vehicle has been employed for many years in coal washeries. It has been used less frequently in hydraulic mining and thermal power station fuel supply systems. The suitability of coal for pipeline transport arises from its moderate specific gravity relative to the carrier fluid and the fact that throughputs are often large and steady over long periods of time."

Jan 1, 1990

By Youngjib Ham

Understanding energy performance of existing buildings is vital to increasing their efficiency and reducing the overall energy consumptions. This entails facility managers to systematically monitor building energy performance and reliably identify and analyze potential problems. Currently, infrared thermography is widely used as a primary diagnostic tool for the detection of building performance problems. Nonetheless, applications of thermal images for building inspection are mainly restricted to manual and labor-intensive identification and qualitative assessment of heating or cooling loss. Automated identification of potential problems and reliable cost analysis of the associated energy loss can help homeowners to minimize financial risk of retrofits and maximize energy savings. To that end, this paper presents a new automated method for calculating the cost of energy loss for building diagnostics. In the proposed method, first, using a hand-held thermal camera, the auditors collect digital and thermal imagery from the buildings under inspection. Then, using a recently proposed method for Energy Performance Augmented Reality (EPAR) modeling, an actual 3D spatio-thermal model is generated and superimposed with a computational fluid dynamics (CFD)-based expected energy performance model. The resulting EPAR model is placed into the method proposed in this paper for cost analysis of the energy loss. Through a new 3D thermal mesh modeling using k-d tree structure and nearest neighborhood searching, performance deviations between these models are automatically calculated. Using a temperature threshold, the areas associated with potential performance problems are detected in the EPAR model and are visualized using a metaphor based on traffic light colors. Then, the actual R-values of the detected areas are measured at the level of 3D points. Based on the measured R-values and the estimated air change rate for the detected air leaks, (1) the heat loss or gain caused either by poor insulation or air infiltration/exfiltration and (2) the associated energy costs are automatically calculated. The proposed method is validated on several locations of existing residential buildings. The preliminary results show the potential of the proposed method for minimizing the inspection time as well as the risk associated with the cost analysis of retrofitting potential building performance problems.

Aug 1, 2013

By L. C. DeCory

"Concrete is a common denominator to the building process and portland cement is an integral and necessary component of concrete. The cost of portland cement is nominal and its cost comprises, in most instances, a small portion of the total cost of ""put-in-place"" concrete.The domestic demand for portland cement in Canada is projected to be slightly less than 11 million short tons in 1980. In order to achieve this projected goal, stabilization or lowering of the cost of put-in-place construction is necessary. This enhancement of the cost of building can be achieved by:(1) improving the building process;(2) refining and improving design techniques; and(3) developing improved and economical concrete products.Some of the techniques and materials that will lead to building cost stabilization include systems building in its broadest sense, slipforming, precasting, prestressing, computer design, lightweight aggregates, fibrous concrete and integration of building components."

Jan 1, 1973

By V. Bondarenko

The importance and necessity of gas hydrates deposits development followed by natural gas extraction is considered in the present paper. Analysis is given to world sources focused on methane hydrates formation conditions. Information covering the most perspective gas hydrate deposit of the Black Sea is presented in the article. Two most common methods of gas hydrates development ? thermo stimulation and inhibitor injection are analyzed presenting their comparative characteristics. Basic scientific trends and developments of underground mining department in the field of gas methane extraction from gas hydrates are scrutinized. Schemes and methods of natural gas hydrates development are shown together with formulas, parameters and factors influencing the extraction process. Also the analysis is given to the possibility of gas hydrates formation from methane-air mixtures of degassing wells from coal mines of Ukraine. Improved experimental unit for gas hydrates formation under laboratorial conditions is presented with its basic characteristics. General conclusions and basic tasks requiring further research are given in the end.

Aug 1, 2013

By Dave N. K., T. P. Lim

"A fast, reliable and accurate method for radium-226 determination in environmental water samples has been devised, using an alpha spectroscopic technique. The correlation between barium-133 and radium-226 in the barium-radium sulphate precipitation mechanism was studied and in the limited experimental recovery range, the coefficient of correlation was r = 0.986. A self-absorption study for various barium carrier concentrations was also undertaken to obtain the least broadening of alpha energy line widths. An optimum value of 0.3 mg barium carrier was obtained for chemical recovery in the range of 85%.IntroductionWith the increase in uranium mining activities, the migration and spread of radioactivity via various environmental pathways is of great concern. Because of its inherent biological hazard and relatively long half-life, (approximately 1620 years), raidum-226 is frequently monitored as a measure of radioactive contamination of the environment. It is, therefore, necessary to modify existing methods for rapid determination of radium-226 in environmental samples for quick corrective measures in the event of seepage, dam leakage or discharge violations."

Jan 1, 1981

By I. Stefanou, J. Sulem

"In the last thirty years, the study of earthquake mechanisms has emphasized the major role of rock friction. Earthquakes appear to be the result of a frictional instability and occur by sudden slippage along a pre-existing fault or a plate interface. Multiphysics couplings play a major role in earthquake nucleation and seismic slip. The effect of shear heating and thermal pressurization may be of prime importance in the control of the stability of shear deformation inside the slipping zone. Other mechanisms in relation with thermal decomposition of minerals affect the pore pressure and the temperature evolution of the system, and can play a significant role in the extreme strain localization observed in field. The actual width of the localized zone is a key parameter for understanding fault weakening mechanisms. On the basis of field observations, laboratory experiments and recent advanced modeling, these phenomena are analyzed and discussed in order to bring some new insights in the understanding of earthquakes nucleation.INTRODUCTIONIn the last thirty years, the study of earthquake mechanisms has emphasized the major role of rock friction. Earthquakes appear to be the result of a frictional instability and occur by sudden slippage along a pre-existing fault or a plate interface (Scholz, 1998; Sykes, 1978). The conceptual model of spring slider system is commonly used to represent the interaction between an elastic crustal block and a fault zone. Stick-slip instability is possible if the softening rate of the shear resistance of the fault zone is high enough as compared to the stiffness of the crustal block. Therefore, weakening mechanisms that can explain how the frictional resistance of a fault decreases with slip and/or slip rate is of prime importance to understand how an earthquake nucleates. In recent years, several drilling programs in active faults (e.g. the Nojima fault in Japan, Boullier, 2011; the Aigion Fault in Greece, Cornet et al. 2004, the Chelungpu fault in Taiwan, Ma et al. 2006, and the San Andreas fault in the U.S.A. Ellsworth et al. 2000) as well as high velocity friction experiments (e.g. Tanikawa et al 2012a; Tanikawa et al. 2012b) have highlighted the physico-chemical processes involved in the nucleation of seismic slip (see for the example the review paper of Niemeijer et al. 2012)."

Jan 1, 2015

By Gordon Sparks, Lyle Kajner

"An often over-looked component in the assessed value of a mining property is the value derived from the ability of the operator to limit financial losses during adverse economic times (i.e. low market price, high energy prices, etc.) by suspending operations. Overlooking the value of this type of operating flexibility when conducting mine investment analysis may negatively bias the risk profile for the investment by over estimating the investment's downside potential, thereby effectively undervaluing the investment. This paper illustrates the nature of the value of operating flexibility and discusses how it may be explicitly quantified within the context of conducting stochastic mine investment analysis. IntroductionMining properties are evaluated using an array of techniques ranging from simplistic non-discounted payback calculation s to sophisticated, discounted-stochastic simulation. Stochastic simulation analysis is perhaps the most robust mine investment analysis technique as it not only provides an estimate of the expected value of the property, but also quantifies the associated risks (for examples of stochastic mine investment analysis, see: Billingsley and Yaychuk, 1986; Gentry and O'Neil, 1984; Munro, 1977; or Harris, 1970).The quantification of risk is important as it provides the necessary yardstick required to allocate the corporation's resources efficiently. Resources are said to be allocated efficiently when the corporation's expected long-term financial reward is maximized while at the same time minimizing its risk (see Hertz, 1968; or Markowitz, 1952 for in depth discussions on efficiency as it relates to investment policy). The efficient allocation of resources should be the objective of any rational corporation. Therefore, rational corporations should employ stochastic evaluation techniques when screening their investments."

Jan 1, 1992

By J. D. Gillaspie, D. T. White

"Sulphuric acid atmospheric leaching of nickel saprolite / garnierite ores was proposed in the early twentieth century, prior to the development of the pressure acid leaching process for limonite ores. Sulphuric acid leaching with alkali addition for iron precipitation as jarosite has been considered periodically since the early 1970s, shortly after the development of the jarosite process for iron control in zinc refining. In the late 1990’s a series of flowsheets were proposed and tested involving simultaneous atmospheric leaching, iron precipitation and acid regeneration. These were considered particularly suited to sequential leaching of limonite and saprolite ores. A number of laterite sulphuric acid leaching processes utilising this chemistry have been put into commercial operation. Similar sequential leaching flow sheets involving precipitation of iron as goethite were also developed and piloted. This paper will firstly describe some of the important historical developments of both the jarosite and goethite processes. It will then provide descriptions of the commercialised processes involving alkali jarosite/alunite precipitation, with special emphasis on the downstream impurity removal requirements necessary for efficient recovery of nickel and cobalt from solution.INTRODUCTION This paper is a summary and extension of previous works with which the authors have been involved, on the subject of sulphuric acid leaching of nickel laterites (Adams, et al., 2004), (Liu H. , Gillaspie, Lewis, Neudorf, & Barnett, 2004), (White, Miller, & Napier, 2006), (White, 2009), (White & Gillaspie, 2013), (White & Gillaspie, 2015). Some of the historical developments of both the jarosite and goethite leaching-precipitation processes will be described, followed by a description of the commercialised sequential nickel laterite leaching processes, involving alkali jarosite/alunite precipitation and acid regeneration, with a comparison to the equivalent goethite based processes. These will include Jarosite Atmospheric Leaching (JAL), Goethite Atmospheric Leaching (GAL) and combined Pressure Acid Leaching – Atmospheric Leaching, termed EPAL®. There will also be an explanation of the downstream impurity removal requirements necessary for efficient recovery of nickel and cobalt from solution."

Jan 1, 2016

By T. Abu Leil

A new class of ternary Mg-Sn-Ca alloys is being developed to address the dual demands of corrosion and creep resistance at service temperatures. While tin has proven to enhance the corrosion resistance, calcium is expected to significantly increase their creep resistance of binary magnesium alloys. Their effects in ternary magnesium alloys are not yet known. The series of alloys studied has Sn and Ca in the ranges 3-6% and 1¬2%, respectively. The results indicate that these alloys have two-phase structures with CaMgSn phase dispersed in a matrix that is predominantly a solid solution of magnesium. The corrosion behavior of these alloys has been investigated by means of salt spray tests and potentio-dynamic measurements. Creep behavior of these alloys was measured at a temperature of 135 C under an applied compressive stress of 85 MPa. Scanning Electron Microscopy with Energy Dispersive X-ray facility and X-ray Diffraction techniques were used to characterize the microstructures. The results indicate the prospect of designing alloys that can provide optimum combinations of corrosion and creep resistance by adjusting the relative compositions of Sn and Ca in the system.

Jan 1, 2006

The goal of this presentation is to firstly, review mine effluent permits in a number of regulatory jurisdictions; and secondly, to develop a strategy for incorporating the regulatory requirements into the environmental assessment (EA) process for new mine proposals. The focus was on the province of British Columbia (BC) and their recent initiative on the One Project, One Process initiative. This task was approached by reviewing mine effluent permits for various regulatory jurisdictions and comparing them to BC mine effluent permits. This comparison revealed a variety of approaches for designing mine effluent permits, but there is a common scientific approach, which supports the conclusion that the permitting of mine site discharges can be designed based on a scientific approach. This approach is expected to: (a) achieve sound environmental protection, (b) demonstrate the application of Best Achievable Technology, (c) incorporate sound sustainability approaches, (d) incorporate regulatory objectives, and (e) create efficiencies for the regulator and mining industry. There is an essential precursor to developing a sciencebased effluent permit for which the proponent must provide: (1) the necessary technical assessment information to demonstrate the mine effluent permit application will result in an environmentally protective effluent discharge, to the satisfaction of the permitting agency; (2) the necessary level of detail for essential mitigation pollution control works to demonstrate how they will be operated to achieve the necessary treatment goals; (3) the necessary level of detail for non-treatment mitigation (passive treatment, or passive pollution control); and (4) the necessary level of detail to demonstrate how pollutants will be prevented from being mobilized (or being generated) from ore and waste materials, or, if the pollutant originates from an added milling reagent, how the reagent will be reduced. While (active) mitigation pollution control equipment is more definable in an effluent permit, non-treatment mitigation is more nebulous in terms of defining in a mine effluent permit; it is therefore recommended that appropriate management plans be developed for essential mitigation pollution control and non-treatment mitigation (passive treatment) and submitted with the proponent?s EA/effluent permit application packages. Major deficits in adequate active and passive pollution control will inevitably lead to regulatory impediments to developing a permit and allowing a mine to be developed, although EA processes strive to preclude major permit information gaps; the onus is on the proponent to provide complete information in this area. Hence the importance of EA processes ensuring that the major technical information requirements for effluent permit development are included in the EA phase. Recently, this aspect of the mine EA process has taken on a new role under the political efforts of One Project, One Review Process (Canadian) and One Project, One Process (in BC). These initiatives translate, in part, to ?synchronous permitting? (in BC): effluent permitting, for example, may be initiated shortly after the proponent submits the EA application to Ministry of Environment.

Aug 1, 2013

The mechanism of thiosulfate decomposition and the products formed were investigated in the presence of pyrite or pyrrhotite in copper-ammonia solutions used for leaching gold. The presence of the sulfides significantly increased the decomposition of thiosulfate. The sulfide-surface-catalyzed oxidation of thiosulfate to tetrathionate by dissolved oxygen or the cupric tetra-ammine complex was proposed to be the dominant thiosulfate decomposition mechanism. The catalysis of the sulfides in this reaction could originate from their strong affinity for aqueous sulfur species and their semiconducting properties. Oxygen was found to be the initial driving force for thiosulfate decomposition in the absence of cupric ions and the driving force for the continuous decomposition of thiosulfate in the presence of cupric ions. Under an oxygen free atmosphere, the decomposition of thiosulfate was limited to reduce the cupric ions and the catalytic effect of the sulfides was also marginal. The dominant oxidative product of thiosulfate was trithionate in alkaline solutions especially in an oxygen rich or cupric ion rich environment. Tetrathionate was found in relatively smaller amounts in an oxygen and cupric ion deficient environment. Tetrathionate was not stable and would further decompose after extended periods. Trithionate concentrations increased almost linearly with time.

Jan 1, 2005

By R. W. Thompkins

"PREFACEThis paper will be published in three parts. Part 1, in this issue, will cover the occurrence of uranium, radiation from uranium ores, the uranium series, radioactive theory, radioactive equilibrium and application to the radon series, the working level, the theory of emanation and diffusion, transport by thermal diffusion of radon emanating from porous rocks, and definitions.Part 2, to appear in the October issue, will deal with radiation theory applied to uranium ores, other radon migration factors , fact ors affecting the radon gas release rate, measurement of radon gas emanation rates, the tunnel concept, variation of emanation rate with grade, and estimating radioactivity from grade analysis.The series will conclude with Part 3, in the November issue, which will discuss the techniques for controlling radiation and give some example calculations.1.0. Occurrence of Uranium1.0.1. Uranium is widely distributed in nature. Sedimentary rocks contain less than igneous or metamorphic rock s and as the outer 10 miles of the earth's crust is composed of 95 per cent igneous and 5 per cent sedimentary rock, it has been estimated that about 1.3 x 1014 tons of uranium exist in the earth's crust.1.0.2. It is not surprising, therefore, that radiation has existed naturally in the ear h ever since the beginning of time. It is found in such places as:(1) non-uranium mines;(2) houses not close to or connected to uranium mines;(3) ground-water tables supplying drinking water to large populations.1.0.3. All mines do not necessarily have abnormal radiation in them, but it is possible for many mines to have abnormal levels of radiation. Therefore, all underground mining operations should be tested for radiation."

Jan 1, 1982