Search Documents

By V. Prodanovic, M. Militzer

Production of advanced linepipe steels with strength levels of 685MPa (100ksi) and higher requires excellent control of runout table cooling to produce the desired final fine-grained microstructures, which may include acicular ferrite. Cooling is exerted on the runout table by applying water jets onto the hot surface of the strip and heat is removed from the steel by forced convective boiling. The associated boiling mechanisms are complex and include film, transition and nucleate boiling. A pilot-scale runout table test rig has been built to systematically study boiling heat transfer from a moving steel plate by employing industrial scale headers. Experiments were conducted using test plates moving at speeds between 0.3 m/s and 1.4 m/s. The plates were cooled down from 850°C to temperatures below saturation by a single water jet supplied through an industrial size circular nozzle. Based on these experiments heat fluxes were determined and further used to develop improved runout table cooling models.

Jan 1, 2005

THE Michipicoten area, one of numerous iron-bearing "Archean" segments in the Shield, contains two main types of iron formation, a normal Keewatin-type, consisting of interbanded chert, siliceous magnetite and jasper, and, gradational to this, a carbonate-sulphide type which contains large de-posits of siderite and pyrite. The carbonate-sulphide type of iron formation bears a direct and intimate relationship to the volcanic development of the area; it there-by affords some insight into genetic problems of Archeanron formation in general. The purpose of this pa-per is to summarize the geological setting of Michipicoten iron formations and to briefly review genetic aspects of recent work in the area. GENERAL GEOLOGY in largely by assorted volcanics and sediments of the Michipicoten series and younger, regional granite masses. (Fig. 1). The Michipicoten series comprises a thick assemblage of mixed flows and pyroclastics together with elastic sediments and banded iron formations. The volcanics belong to the Andesite-Rhyolite Association, and characters-

Jan 1, 1961

By G. P. Gu

The in-service 90/10 cupro-nickel tubes in a water-chiller system suffered from severe corrosion damage during their relatively short service life causing unexpected down time. In addition to downtime, the environmental risk associated with losing refrigerant was also a concern that initiated this investigation, Microstructural investigation using SEM and electron microprobe indicated that pitting corrosion had resulted in local nickel depletion, During the corrosion process, copper appeared to have re-deposited around the corrosion pits accelerating the local corrosion.

Jan 1, 2005

By J. Lipp

The lion share of lithium produced globally originates from South American salars. The standard operation for lithium production utilizes an array of evaporation ponds. This process consume vast areas and is either very slow when relying on solar evaporation - roughly 18 months of residence time; or with very high energy consumption since over 90% of initial water volume needs to be evaporated. A new technology, based on solvent extraction was developed. Results indicate a distribution coefficient up to 30, and selectivity greater than 1,000 towards Na extraction. The loaded solvent is stripped using a strong mineral acid, and the product solution is the lithium derivative of that stripping acid. Utilization of this new LiSXTM technology results in reducing the area needed for a commercial plant as well as reduces the residence time. In addition applying different stripping acids can diversify the product line of such facility.

Jan 1, 2014

By M. Fafard, D. Picard, J. -F. Bilodeau, G. Soucy

To simulate adequately the behaviour of a Hall-Heroult electrolysis cell, a finite element model must take into account the properties of each material. However, it has some lacking knowledge on the mechanical behaviour of materials, like the long-term visco-elastic (creep/relaxation) behaviour of cathode. A three-dimensional model is then proposed in this paper and will be ready to be implemented in the finite element code FESh++. The model was developed using the three-dimensional model based on thermodynamic of irreversible processes where the choice of the internal variables is based on a phenomenological approach. All parameters of the model are represented by constant constitutive tensors and the temperature and chemical dependencies are taking into account through scalar functions multiplying the constant constitutive tensor. The goal of the first part of this project was to determine the parameters of the threedimensional visco-elastic model at the reference state (virgin material at ambient temperature) of three different cathode materials. This paper presents the theoretical model and the results of creep tests at ambient temperature for the semi-graphitic carbon cathode.

Jan 1, 2006

By J. A. Brusset

THE Greenhill mine of West Canadian Collieries, Limited, is situated at Blairmore, Alberta, and produces 2,500 tons per day of bituminous coal. On Monday, October 25th, 1943, smoke was discovered by a party of firebosses on their regular weekly inspection of air-ways. Probably the fire had been smouldering for several days but, as it had started on the outcrop at the top of an old raise filled with dirt, only a small quantity of smoke could filter through, and the plume of mist that crowns the fan at that season had prevented the fan-man from noticing it. This raise is only about 200 feet from the fan, and is 70 feet long between the fan-drift and the outcrop. It was impossible to prove the origin of the fire, as it had probably started several days before it was discovered, but it is possible that a careless smoker may have thrown a match into the opening at the outcrop, and that the old, dry timber had caught fire. The airways are in No. 2 seam, a bituminous seam 18 to 25 feet thick surmounted by shales and sandstones. Only 45 feet vertically above it is No. 1 seam, 12 feet thick, overlain by a strong conglomerate. In that vicinity, No. 1 seam had been worked out about ten years ago and the strata between the two seams are undoubtedly fissured. The pitch of both seams is 43 degrees.

Jan 1, 1945

By M. Fairclough, B. Moldovan

Insights into uranium mining projects of the future can be gained by a careful statistical analysis of past and present deposits, as well as an examination of recent trends for uranium resource evaluation and primary uranium production. The International Atomic Energy Agency (IAEA) provides the necessary data and corresponding mechanisms as inputs for methodologies that enable strategic and scientific evaluations of long-term security of supply uranium required to sustain the demand for nuclear fuel. Sustainability of the uranium mining industry and subsequently new uranium mines of the future requires innovation and expertise to lower operating costs, maintain or improve uranium recovery while meeting the requirements of stakeholders in regard to protection of the environment and safety of the workers and general public.

Jan 1, 2020

By L. Nutter, J. Clancy

"Barite is used extensively by the oil and gas well-drilling industry as a weighting agent. It is particularly well suited for drilling mud because of its qualities; it is non-abrasive, heavy, virtually inert chemically, easy to handle and inexpensive compared to other available heavy materials. Increased deep well drilling in Western Canada, and especially in the Arctic regions, could dramatically affect the demand for barite through this decade. Known deposits in northeast British Columbia are possible sources of incremental barite supplies, should the situation develop.IntroductionThe purpose of this report is to examine the opportunities for expanding barite production in British Columbia. Of primary interest will be the relationship between the projected future levels of production and consumption of barite in Western Canada and the extent to which increased domestic production could replace the need for imports in filling any expected supply shortages.After a brief overview of the nature and uses of barite and some of the relevant features of the barite supply industry, the discussion will turn to the supply gap in the Canadian market and the possibilities for import substitution.OverviewBarite is an industrial mineral which is used in large quantities by the oil and gas well-drilling industry. It is often an important component of drilling mud, a fluid circulated continuously in the well during the drilling process to lubricate and cool the drilling apparatus and to contain the high oil and gas pressures found at depth. Barite (BaSO4) is particularly well suited as a weighting agent for drilling mud because it is a heavy (specific gravity to 4.5) inert mineral which is inexpensive in relation to other materials having a high specific gravity. In the on-site use of drilling mud, ground barite is combined with numerous other solid ingredients and chemicals in the form of a slurry. Other advantages of barite include cleanliness, ease in handling and its non-abrasive character (hardness of 3-3.5)."

Jan 1, 1982

By P. J. Adams

Environmental regulations require means for controlling emissions of SO2 NOx and particulate when burning coal. The combustion of coal in limestone fluidized beds is one of the most promising techniques for the necessary reduction in emissions. Fluidized-bed firing, furthermore, offers potential economies in capital equipment. The world's largest steam generator applying fluidized-bed techniques was built under the sponsorship of ERDA and installed in Rivesville, West Virginia. This paper describes the design and discusses the start-up and development difficulties which were experienced during the period from initial operation to current readiness for commercial operation. Other developments leading to utility and industrial fluidized-bed steam generating equipment are reviewed. The future potential of this promising technique is discussed.

Jan 1, 1979

By Guy Chevalier

QCM?s pellet plant, located in Port-Cartier, Quebec, produces up to 8.6 million tons of iron ore pellets annually. Four different types are produced: three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the installation of new process equipment to improve the reducibility of direct reduction pellets (DR pellet). The findings, the equipment selection and some post start-up modifications are presented. This low silica DR pellet is used in Midrex and HyL shaft furnaces. A good DR pellet has to meet strict chemical, physical and metallurgical specifications. An important metallurgical property is its ability to release oxygen when exposed to reducing gases. Considering that the market for DR pellets is expanding and being aware that reducibility is critical for our clients, a program to improve the latter was undertaken. Test work showed that one factor which has a negative effect on reducibility is the proportion of particles larger than 75 microns. Knowing that the best way to reduce the amount of coarse particles was to close our open grinding circuits, we began evaluating the most suitable classification equipment applicable to our process operations. We settled on hydro-classifiers based on their very sharp cut and their low operating costs. In light of the hydro-classifiers performance it was also decided to replace the hydro-cyclones of an already closed circuit.

May 1, 2003

By J. Chlan

"Dryer DescriptionProctor and Schwartz Continuous Conveyor DryerThe Proctor and Schwartz Continuous Conveyor Dryer has been in operation since July 1958, and comprises six unit• - an 8• wide single conveyor with roller extruder, insulated housing, type 304 stainless steel circulating and exhaust fall system, steam heating coils, temperature controls and discharge crusher rolls. Entire dryer dimensions are 52’ x 12'0""weighing 53,000 lbs,Extruder rolls - setting is 1/8"" (Drive 3 HP 1800 RPM) clearance off the extruder screen.Conveyor - consists of 151 interlocking pans, measuring 8"" x 8' (2 HP 1200 RPM) One Exhaust Fan (5HP - 900 RPM)Steam Coils -- l"" steel pipe - with steel fins -- each coil measures 16' 2’’- 64 coils in the No, 1 Compartment- 64 coils in the No, 2 CompartmentDryer OperationThe yellowcake slurry at 28% solids is pumped to an 81 x 8' Peterson Filter. The filter media presently being used is a Neotex 4372 blanket, being 100% staple fibre nylon, 12 oz per square yard with air porosity of 9 CFM's. The cake discharge at 45 - 50% moisture falls into the roller extruder. Extrusions are formed by forcing the material by rolls through a perforated plate moving back and forth and depositing the spaghetti-like extrusion on onto the dryer-conveyor.The conveyor now carries the extruded material through the heating chamber•, The feed end of the dryer will be referred to as No. 1 Compartment, with temperature control set at 280""F. The circulating fans take the hot air off the coils and circulate the heated air through the perforated openings in the dryer conveyor pane, After passing through the set of steam coils and circulating fan in No, 1 Compartment, the material then goes through No, 2 Compartment where the temperature is set at 305'F, Final material then discharges through a set of crusher rolls set at ~"". Moisture of final dried product runs at less than 2%.The dryer conveyor load is usually run to a 3"" - 4"" depth load. Conveyor speed at approximately 90 minutes for load to pass through. Load onto the conveyor is controlled by boot level and speed of the 8' x 8' filter. The dryer steam coils are water-washed twice a month."

Jan 1, 1972

By A. Bendada, P. Servais, X. P. Maldague, C. Ibarra-Castanedo, C. Mohr

Infrared (IR) thermography is a nondestructive, non-contact and non-intrusive technique that allows the fast inspection of large and complex structures with limited accessibility. Pulsed thermography is particularly interesting for the inspection of aerospace materials such as composites given that, after submitting the specimen surface to a thermal front, the most common types of subsurface discontinuities (e.g. porosity, de laminations, dis bonds, fiber breakage and inclusions) can be detected with an IR camera as regions showing abnormal temperature patterns. We present first the case of an aircraft door with water ingress and surface repairs on its honey comb structure. We also highlight the advantages and limitations of thermography for the inspection of aircraft composite parts, such as edge flaps, rotor blades and speed breaks. Finally, we expose some results from a Kevlar® non-planar specimen with Teflon® inclusions at different depths and locations.

Jan 1, 2006

By M. A. Stogran-Baker, S. Cole

"Fluorspar mining occurred in the St. Lawrence area from the 1930s until the mid 1980s. In 2013, CFI discovered a new ore body, the AGS vein, which proved amenable to more economic open pit mining methods. A new mill was designed to produce 200,000 tonnes per year of high quality, acid-grade fluorspar concentrate. The simple mill flowsheet includes crushing, dense medium separation (DMS), grinding, sulphide flotation, pulp thickening, fluorite flotation, thickening, and concentrate filtration. The type of flotation cell used is being installed for the first time in North America. Site clearing commenced in the spring of 2016, followed by mill building erection completed by the fall of the same year. Civil and mechanical installation as well as site-wide construction was completed by the end of September 2017. Commissioning commenced, and at the time of paper submission mill production is on track to ramp up to full capacity by the beginning of 2018. This paper will focus on the use of fluorine NMR analysis applied to fluorite and the development of on-stream analysis, flotation cell selection and the decision to install the new cells, and the water control program designed to maintain process control with the least possible environmental impact.HISTORY St. Lawrence is located on the south-eastern coast of the Burin Peninsula in Newfoundland and Labrador. The first occurrence of fluorspar in the St. Lawrence area was recorded in 1843 by British geologist J.B. Jukes (DNR 2010). Fluorspar was likely extracted in small quantities prior, however commercial fluorspar mining did not commence until 1933 at the Black Duck Mine. The Black Duck Mine operation processed ore by washing and screening – acid-grade was hand-picked from the oversize, the undersize was sold as a lower grade product. The Black Duck Mine was closed in 1941 (Wilson 2010). The American Fluorspar Limited (New Fluor) commenced operations on the Director vein in 1936, and was bought by Alcan in 1942 (Cooper 2012). Alcan also developed the Iron Springs as well as the Tarefare deposits. The Black Duck Mine mill had closed, and a new mill was built. This new mill crushed the ore prior to dense medium separation, the sinks of which were sent to Quebec for use in Alcan’s aluminum smelter (CFI 2016). Alcan shut down it’s mining operations in 1977 due to the dropping price of fluorspar as well as labour disputes. In 1986, the British-based Minworth Limited began producing ore from underground at Blue Beach North and Blue Beach South, as well as from open pits at Tarefare and Director veins (Cooper 2012). A new mill was built by Minworth in order to process the ore using flotation to produce an acid-grade concentrate. The low price of fluorspar caused Minworth to shut down operations in 1990. Whilst exploration has been ongoing, no mining had occurred in the area since 1990."

Jan 1, 2018

By A. McGrath, M. Trovant, M. Haque

Minimizing energy consumption is a priority for many industrial facilities. Metallurgical and gasification processes produce dirty syngas (CO and H2), which offers the potential for energy recovery. However, syngas handling can pose an explosion risk and even minor leaks can result in poor workplace hygiene. Furthermore, many jurisdictions around the world now discourage wet syngas handling due to limited water availability and secondary pollution. Hatch has developed a 100% positive pressure gas handling system that targets these safety hazards without using fresh water. The implementation of a system for calcium carbide smelters at Qinghai Salt Lake Industry Co. (QSLIC) in China is profiled as a case study.

Jan 1, 2015

By Carmen M. Neculita

Optimizing the long-term efficiency of passive systems for the treatment of highly contaminated acid mine drainage (AMD) is still a challenging issue. The optimization lies, among others, on improving the understanding and quantification of metal removal mechanisms in order to predict and enhance the stability of neo-formed minerals in secondary phases. Sorption, and precipitation as oxides-hydroxides, carbonates and bio-sulfides are likely the most important metal removal mechanisms involved in passive biotreatment of both slightly and highly contaminated AMD. In the same time, the preferred mechanism is precipitation of metal sulfides that are more stable and less pH dependent than carbonates and oxides-hydroxides. However, results of relatively recent research studies performed at laboratory scale showed that sulfides accounted only for up to 15% of total metals removed in passive bioreactors treating highly contaminated AMD dominated by iron (around 500 mg/L). Several approaches were used in the aforementioned studies to understand and quantify metal removal mechanisms in spent reactive mixtures collected from long-term (12-15 months) operating column bioreactors. These included: thermodynamic equilibrium modeling and various chemical extractions and mineralogical analyses (such as single and sequential extractions, acid volatile sulfides-simultaneously extracted metals determination, scanning electron microscopy, X-ray diffraction, and thermo-gravimetric analysis). The large proportion of metals (85%) removed by sorption and precipitation as oxides-hydroxides and carbonates suggests a relatively high mobility of the neoformed minerals, especially in low pH conditions. However, no data is available on the long-term stability of spent reactive mixtures and, on the implications for the sustainable management of this type of solid waste. Lately there is almost a consensus that the efficiency of highly contaminated AMD treatment is warranted by the use of multi-step passive systems, including both chemical and biological units, installed sequentially. However, very few well-documented studies are available on the design, construction, operation and long-term efficiency of these multi-step systems. A leading example is the tri-unit passive system installed on the abandoned Lorraine mine site (Québec) to treat a highly contaminated AMD dominated by iron (about 2,500 mg/L). This tri-step system (160 m3), consisting in two bioreactors separated by a unit filled with wood ashes, achieves to date a satisfactory removal of iron (up to 99%). Moreover, based on the data collected during laboratory testing, iron was mainly removed in the wood ashes unit (from around 3,200 mg/L to 10 mg/L) by precipitation of oxides-hydroxides as predominant mechanism and only partially by sorption. However, no data is available on the actual metal removal mechanisms in the field. Overall, theses multi-step systems are more complex and their long-term performance is even less predictable than the single unit systems. This paper presents the current knowledge and the research needs on metal removal mechanisms in passive bioreactors and multi-step systems for the long-term treatment of highly contaminated AMD. KEYWORDS

Aug 1, 2013

By Tim Gitzel

Thank you for your introduction, and thank you to the CIM for inviting me to make a presentation to you today. This is my first opportunity to report to you on the status of the Canadian uranium industry and I am pleased to tell you that the industry is in good shape, and well positioned for the future. As you will no doubt be aware, Saskatchewan benefits from the world?s largest known highgrade deposits of uranium as well as from a high level of provincial, public and northern community support. It is within this unique combination of geology and community that our industry operates. Uranium markets have been extremely competitive for a number of years for several reasons. First, deregulation in the nuclear electric power industry has tended to encourage fuel buyers to use up their large inventories built up at a time when rapidly increasing demand was anticipated. Second, alternate sources from surplus commercial stocks, military materials and reprocessed fuel have presented a major additional source of uranium supply. Today, these secondary supplies are meeting about half of uranium reactor feed requirements. Canada (that is, Saskatchewan) is the world?s largest ?natural? uranium producer with about a third of the global production. Saskatchewan?s mines produced more than 30 million pounds of yellowcake in 2002. Despite low prices, steady demand for uranium will continue. In fact, an increase in world uranium production in 2002 helped feed a more than 3 per cent increase in reactor fuel demand. Low cost production is important for surviving low market prices, but investments are based on longer-term strategies rather than simply responding to market cycles. Cost is not the only issue. In these times of increasing regulatory and public scrutiny we must continue to earn the trust of our stakeholders by adopting the highest standards and staying on the leading edge of technical, social and environmental developments. Managing these issues is as important as traditional concerns of ore grade and cost of production. The last two decades of the 20th century saw the Province of Saskatchewan rise to prominence as the leader in uranium production from facilities, which were at the time deemed world class. These facilities are now either at - or nearing - the end of their production years. We are now bringing on new facilities that will position Saskatchewan to remain the world leader in uranium production for many years to come.

May 1, 2003

By G. N. Carlson, C. H. Hazelroth, D. R. Dorrance

"Located on the north shore of the St. Lawrence River at Pointe Noire, Quebec are the agglomeration and ship-ping facilities of the Wabush Mines complex. Here, the specular hematite concentrate from the Scully Mine is received for further processing. Modern facilities for handling the ore, either to the 1plant or to stockpile, provide quick and efficient operation of the ore receiving station. Physical preparation of the ore for balling is accomplished with regrind ball mills, filters, bentonite crushing and drying facilities, pumps and related conveying circuits. Rotating table feeders deliver the reground and de-watered ore from storage bins to balling drums, where green ball or green pellet formation is achieved. The green balls are then conveyed to the indurating section. Three Dravo-Lurgi travelling grates, producing a total of 6,000,000 long dry tons of pellets per year, are used in the indurating phase of the operation. These grates, having 38 windboxes and firing at a temperature of 2,500°F, harden the pellets for shipment to various blast furnaces throughout the world."

Jan 1, 1969

By C. G. McLachlan

Professor H.E.T. Haultain: To me from time to time the urge comes to say the agreeable thing as well as the disagreeable in commenting on the work of others. It is a prerogative of age. I don't apologize. To myself I justify my action as based on a long experience of the matters with which I deal, and I like to tell myself that I have a certain responsibility in such matters on account of my detached position. This Noranda article is a very fine contribution concerning Canadian milling, and I am surprised that no word of commendation or thanks has appeared concerning it in the BULLETIN. There is altogether too much written in these days by men rushing into print, concerning laboratory work, that has not been tied into, nor has resulted in application in the field. The authors of this paper have not rushed into print. The preparation of this paper was evidently an uncongenial task. If the authors had been that way inclined, it could have spread over several lengthy papers. It is an important article because it represents an enormous amount of work in the laboratory and the mill, extending over a period of sixteen years, and resulting in fine metallurgical and economic results with a very difficult and involved problem. It is a fine article because it is so well prepared and presented. It deals with an unusual ore condition, but there is much in it of use to every cyanide millman. It leaves very little room for criticism, though there may be differences of opinion in regard to some of the chemistry phases with which I am not conversant. I am struck by the enormous amount of persistent, painstaking, conscientious research work involved, and in the careful, sincere way in which the methods and difficulties have been described. Persistence and sincerity are the key note of the effort. It should have a good educational effect on the rising generation of millmen, and it should continue for long as a work of reference, and a spur to others. There has been an important by-product, the training and development of the young men engaged in the work. Three of them became superintendents of important mills. One was sought for important work in Africa, another has joined a large research organization in the United States.

Jan 1, 1946

By Chris Twigge-Molecey

"Over the last 50 years there has been a dramatic evolution in the metallurgical engineering field in Canada. In the 60s the field was dominated by large American and UK groups, often selling major process and equipment packages. The local content was limited to wrap around facilities and the civil and structural work. The mining and metallurgical companies had strong internal teams to lead these projects. Over the decades and business down cycles the large foreign contractors disappeared or re-structured and the mining companies largely shed their engineering and project management groups. The resulting gap was filled by a cadre of local specialist engineering companies, some of whom have grown to be world leaders in the field. The paper traces this evolution and examines the underlying causes and consequences."

Jan 1, 2015

By D. Madsen, B. Salamondra, A. Moss, D. Etienne

"Raise mining at the Namew Lake Nickel Mine in Manitoba uses 3 m diameter bored raises driven at 45 to 50 degrees dip for stope access and drilling. These raises are developed within the orebody on 20 m centres to accommodate electric-hydraulic longhole jumbos and charging wagons. Critical elements of stope development include delineation of are contacts, control of deviation during raise development, optimal stope sequencing to permit a high extraction rate, drill anchorage installation, production drilling and blasting, and ground control. Procedures to deal with these elements are described, with emphasis on the geotechnical investigation for design of open stopes and pillars.Although mining with drilled raises does not have the flexibility to follow large variations in orebody dip, results to date indicate that it can be used successfully in the thicker ore zones. Thinner zones are currently mined using a modified Avoca method. Some flexibility to accommodate variations in orebody dip in thin are zones may be obtained by using alimack raise climbers to drive access raises, and carry longhole drills and charging equipment. Rock quality has been sufficiently good to maintain stable stope walls for full-height mining of primary stapes at 20 m strike length.IntroductionThe Namew nickel deposit is located 60 km south of Flin Flon, Manitoba. It is a moderately dipping (45 to 50 degrees) pipe-like ultramafic intrusion with a sulphide halo enrichment. The diluted recoverable ore reserves at January I, 1990 are 2.2 million tonnes grading 2.05% Ni and 0.7% Cu. The operation is a joint venture between Hudson Bay Mining and Smelting (60%) and Outokornpu Mines Ltd. of Toronto (40%). The mine is budgeted to produce 530 000 tonnes in 1990. The deposit was discovered in 1984 and mine development commenced in 1987.In the raise mining area, primary stopes will be filled with a high quality backfill consisting of cement and quarried limestone. Secondary stopes will be mined out between the primaries in the second pass of mining. The design extraction rate is 94% over all.The orebody above 120 level has an average mining width of 2.4 m, so is too narrow for raise mining. A modified form of Avoca stoping is used."

Jan 1, 1991