Search Documents

By Frank Martonhegyi

"The objective of this paper is to review the coal basins in the Canadian part of the Western Cordillera to aid their understanding, and to aid in finding and proving places of economic coal mining potential. Coal occurs in eugeosynclinal basins in the Western Cordillera which evolved through three stages: -from systems of volcanic arcs in the Late Jurassic to mid-Cretaceous; -through an intermediate stage with deposition in increasingly restricted successor basins in Jurassic to Early Tertiary; -to a continental stage by the Eocene. Minor coal seams occur usually in late volcanic arc stage sediments bur they can be locally thick as they are on Queen Charlotte Islands. Successor basins usually show a marine-paralic-limnic evolurion. Signijicanr coal deposits occur in the tarter two sequences in the Whirehorse (Tantalus) and Bowser (SkeenaSusrur) basins. Currenr activities are intensive in the more accessible Bowser Basin, for example at Telkwa, Susrut River and on the Groundhog coal field. On Vancouver Island major coal seams occur in cyclic sediments, but the more accessible deposits are mined our. Exploration renewed recently in the less accessible northern part of the Island, for example Quinsam, for surface mineable coal. The Western Cordillera is a mosaic of allochtonous tectonic blocks. They originated from the south and were displaced northward by several hundred kilometres. Many Tertiary coal basins are related to strikeslip transcurrent faults along which the later part of displacement took place, for example the Dawson coal area in the Tintina Trench. Tensional and dipslip normal faulting also created or enhanced sites for thick peat accumulation. For example at Hat Creek 280 m of coal occur in a 550 m section. Secondary structures are often better exploration targets than the main fault zones. Pluvial and alluvial fan environments away from the main drainage are usually the favourable sites for thicker and cleaner coal deposition."

Jan 1, 1985

By Bruce Chalmers

INTRODUCTION TIE most important practical problem with which Physical Metallurgy is faced is the control of the mechanical properties of alloys. The most difficult aspect of this problem is the development of new alloys with the properties that are required for meeting exacting engineering requirements. A great measure of success has been achieved by following the empirical method and most, if not all, of the present variety of alloys have been developed by the process of experiment and observation or trial and error. It may, however, be that this method will become. less productive as time goes on, and that eventually it should be replaced by a process based on an understanding of the factors that determine the properties, so that alloys can be 'designed' to meet the requirements. This method of investigation will not be possible until a much better fundamental understanding of metals has been gained, and this will come only about as a result of a great deal of detailed research. The subject of Physical Metallurgy can be divided, as follows, into two parts: we may consider the factors which determine the structure, in the broadest sense, of an alloy. These include the composition and also the treatment to which the material has been subjected. The second aspect is the influence of the structure on the mechanical and other properties. In order to make an effective contribution in this field, it is necessary for an individual or a group to concentrate on a specific and very restricted topic. It is proposed to discuss in some detail the particular subject in which the writer and his colleagues are working.

Jan 1, 1951

By Sangjian Zhang, Zhu Xiao, Lairong Xiao, Rushi Chen, Mei Fang, Zhou Li

The copper-graphite metal matrix composites were fabricated by two different production methods: directly sintering with copper and graphite (Cu-Gr composite), and in-situ sintering with cuprous copper and graphite (Cu2O-Gr composite). During the in-situ reaction sintering, a redox reaction occurs at the interface of the Cu2O particles and Gr particles, resulting in the improved physical and mechanical properties of Cu2O-Gr composites. Compared with Cu-Gr composite, Cu2O-Gr composite has a higher compression strength at any given graphite content due to the improved interface bonding and uniformly distributed fine graphite particles in the matrix. Increasing graphite content decreases the mechanical properties of the copper-graphite composites. The compression strength of Cu2O-Gr composite is 50-100 MPa higher than that of Cu-Gr composite. INTRODUCTION Copper-graphite composites have been widely used in industry due to their low density, relatively high strength and hardness, good thermal and electrical conductivity, arc ablation resistance and self- lubrication ability (Grandin & Wiklund, 2018; Han & Xu, 1999; Huang et al., 2017). Electric sliding contact friction pair in the high-speed railway system and motor brush in electric contact components have a very high demand on electrical conductivity and self-lubrication ability of materials. The electric devices need to bear both mechanical load and high electric current. Copper-graphite composites with good mechanical, electric and self-lubrication properties are the best candidates for application in multifunctional electric sliding contact frication components. The relative sliding speed of friction pair is developing towards 100 m/s or even faster, which can withstand the electric flow of more than 800 A, and it is often accompanied with vibration and impact (Guo & Ding, 2008). Conventional wear-resistant materials can no longer meet the current requirements and this promotes the development of copper- graphite composites with excellent comprehensive properties (Ding, Chen, Zhu, Zhang, & Zhou, 2009; Yasar, Canakci, & Arslan, 2007). There are many ways to fabricate copper-graphite composites, mainly including powder metallurgy method, liquid immersion infiltration method, rapid sintering method and electrodeposition method (Kalin & Poljanec, 2018; Kim, Lee, & Han, 2014; Liu et al., 2018; Wang et al., 2018). Each method has its own advantages and disadvantages, and the powder metallurgy method is the most commonly used one due to its simple process, high economic benefit, and industrial production applicability. The common steps of the powder metallurgy method are as follows (Samal, Parihar, & Chaira, 2013): firstly mixing the copper (copper alloy) powders and graphite with a certain ratio, following by die-forming, and then sintering at the high temperature with or without pressure. The advantage of copper-graphite composites is that the graphite distributed in the copper matrix uniformly and it can form a carbon diaphragm preventing the wear of the composite (Fu & He, 2010). However, the bonding strength of the interface between the copper matrix and the graphite is relative low as the combination between them is mechanical interlocking but not metallurgical bonding (Ma et al., 2008). It is meaningful to develop new fabrication technology of copper-graphite composites with better interface bonding, which could provide guidance for the design of copper-graphite composites with excellent comprehensive properties.

Jan 1, 2019

By J. B. Watts

"THE Mine Engineering Department at Gaspe Copper is staffed by a chief engineer, assist-ant engineer, research engineer, chief surveyor, four instrument men, chief bonus clerk, draftsman, and a helper pool of four permanent men plus one or two students in the summer. The men are grouped according to function for organization purposes. Routine services provided by the Mine Engineering Department in-elude ail surface and underground surveying and mapping, preparation of working drawings, compilation of engineering reports, recommendations on ventilation, testing the mine air for carbon monoxide, research on mine equipment and its use, and the calculation of incentive bonus. Demand jobs from departments other than the Mine Department .are done on request. Such jobs may be in the plantsite, the Town of Murdochville, or at the shipping points at Gaspe harbour or the St. Lawrence river."

Jan 1, 1959

By P. G. Keohane, J. S. Drake

"Cominco's Polaris Mine is a lead-zinc underground operation that began commercial production in early 1982. The mine site is located on Little Cornwallis Island in the Canadian Arctic at a latitude of 75°23'N and at a longitude of 96°55'W. The nearest settlement, Resolute Bay, some 100 kilometres southeasterly from the mine, is accessed from the mine by light aircraft. The mine site can be accessed by sea during the six-week ice-free period each year. During this time all major operating supplies are brought to the mine and the lead and zinc concentrate products are shipped out to market.GeologyThe Polaris orebody lies near the top of the Thumb Mountain Formation of Ordovician age. This formation is a relatively homogeneous section of thin to medium bedded limestones which are brecciated and dolomitized in the area around the orebody. The deposit is described as a Mississippi Valley-type orebody. Ore minerals are sphalerite and galena with the waste being predominantly dolomite with calcite and marcasite. The ore is quite porous with voids being generally filled with ice as the mineralized zone lies entirely within permafrost. Reserves consist of about twenty million tonnes of ore grading 3.8% Pb and 14.3% Zn with a further three million tonnes of inferred ore at a slightly lower grade.The orebody strikes in a north-south direction with the hangingwall dipping at about twenty degrees to the east. It is generally conformable with the stratigraphy. The footwall in the western portion of the orebody, the Panhandle, lies about 10 to 30 metres below the hangingwall. To the east the footwall drops sharply, creating an orebody height of up to 110 metres in what is referred to as the Keel Zone. The Panhandle Zone has typically 80 - 110 metres of cover above the hangingwall , About 25% of the reserves are in the Panhandle Zone, the remainder being in the Keel Zone. Figure I illustrates a plan view of the orebody relative to other surface facilities on the property and Figure 2 illustrates a simplified section through the Panhandle and Keel Zones."

Jan 1, 1985

By J. E. Hawley, R. C. Hart

"The Preston East Dome gold mine is in the southeastern part of Porcupine district, Ontario, 5 miles southeast of Timmins, and immediately south of the property of Dome Mines, Limited.The claims now owned by this Company were originally staked in 1909. After the property had remained dormant for many years, the present Company was organized in 1936 to resume development operations. Two shafts had been sunk: at the time of the early work on the claims, but lateral work from these failed to reach the ore deposits. A successful diamond drilling campaign undertaken under the direction of D. G. H. Wright, however, was followed by the sinking of a five-compartment shaft arid the erection of a mill. From the start of operations to the end of 1944, 1,292,000 tons of ore averaging $11.60 in gold a ton have been mined.An outstanding feature in this mine is the occurrence of the major gold deposits in quartz porphyry intrusives, though minor deposits are also found in the adjacent Keewatin volcanics. Most of the ore occurs in fractures, but the filling was accompanied by varying degrees of replacement of schistose wall-rocks. The ore deposits may be classified as:"

Jan 1, 1954

By Chin J. Chang

Powder metallurgy (P/M) technique is known for its capability of producing near-net-shape parts. Its specific characteristics have resulted in low cost and eliminated of many secondary machining. However, more and more P/M parts do require additional operations to fulfil their complex geometric features and surface roughness. Many of the machining factors that influence the machinability of cast and wrought steel parts, such as cutting speed, feedrate, coolant, tool geometry and shape, are also considered in the machining of P/M components. The special feature in P/M structure is the porosity that can decrease the machinability and shorten the tool life. Different variables have been considered in the machinability of P/M materials. Densities and the free machining additive manganese sulphide (MnS), are the two main factors of material composition, which dominate the P/M machining performance. Machining process is the main method that generates the desired working surface of machining components. This paper will discuss the metallurgical structure of the powder metallurgy components, their physical properties and possible issues when encountering machining operation. Turning operation has been tested in this investigation to show the relationship between the cutting speed, federate, cutting forces and chip formation. This investigation also discusses how the free machining additive, manganese sulphide, affects the P/M structure and machinability in order to understand how the metallurgical structure can affect the machining operation and, how to obtain the optimised surface results.

May 1, 2001

By P. Czaja

The paper presents a patented and copyright protected concept of constructing a shaft lining that goes through rock masses having strong rheological properties and being susceptible to leaching. In the case of salt layers, especially at significant depths (over 900 m) the relative convergence of the heading contour may amount to 40 ?/year. That results in the fact that any other method of securing the shaft lining, e.g. by making it flexible, will not be sufficient to ensure the stability of the shaft reinforcement geometry. In the new shaft lining concept the excessive rock creep into the outbreak inside the shaft diameter will be removed by local and controlled leaching of the shaft cheeks by means of fresh water directed through a porous medium at the contact layer behind the watertight tubing lining. The paper presents the structure of such a lining and an outline of the construction technology. In order to implement such a lining, a typical tubing will be applied. Separate design and manufacturing will be required for the technological rings used to control the leaching process behind the lining.

Aug 1, 2013

By L. Henry Smith, David C. Arthur

"The Williams Mine is Canada’s largest gold producer, with annual production of 450 000ounces from 2 300 000 tonnes of ore. Highly mechanized and automated underground mining practices are employed in order to achieve and maintain high levels of productivity and minimize costs.The mine ventilation system is modified to include a new vent raise and variable pitchvane-axial fan. This addition allows several fan installations underground to be decommissioned. A substantial net savings in installed horse power is achieved.Heating costs associated with under-ground ventilation air are a significant portion of mine operating costs. Air heating costs are substantially reduced by recovering heat from upcast exhaust air, minewater and compressor cooling circuits. This waste heat is used to supplement propane fired air heating systems for underground ventilation air. An additional benefit is the availability of a heat sink for summer cooling of the compressors.System design, energy savings data and payback calculations are presented."

Jan 1, 1996

By I. P. Swainson, A. Ilbagi, H. Henein

Powders of Al-50wt%Ni, Al-40wt%Ni and Al-36wt%Ni were produced using the Impulse Atomization technique, a rapid solidification technique. The molten droplets were cooled in-flight by the stagnant helium or nitrogen in the atomizing chamber. The resulting powders were sieved into different size ranges. X-Ray diffraction and neutron diffraction were used in order to quantify the phase fractions in the samples. The computer software GSAS was used to calculate the weight fraction of the existing phases, namely Al3Ni2, Al3Ni and Al, by profile refinement method. The effect of processing parameters, alloy composition and particle size will be discussed in this paper. In brief, no AlNi was found in any of the samples analyzed. Higher cooling rates resulted in the reduction of the ratio of Al3Ni/Al3Ni2. Also, at high cooling rates, Scheil closely predicted the ratio of Al3Ni/Al3Ni2. Some metastable phases were found in Al- 36wt%Ni.

Jan 1, 2010

By M. E. Holter

"Three main potash members are recognized within the Prairie Evaporite Formation of Saskatchewan and have been designated, in ascending order, the Esterhazy, Belle Plaine and Patience Lake members. Each is composed of sylvinite near the geographic center of the member and becomes increasingly carnallitic marginally. Each stratigraphically higher member has a narrower carnallitic margin. The sharp contact between carnallitic and non-carnallitic components of the formation describes a surface which may be traced regionally and is not related to bed-ding. The contact rises higher in the stratigraphic section toward margins of members. Within each of the three members, analyses indicate that carnallite becomes more abundant toward the north whereas sylvite and insolubles, increase toward the south. Within each member, areas rich in carnallite are coincident with areas in which the member as a whole is thicker than averag,e. The Belle Plaine Member contains the highest concentrations of carnallite, the Esterhazy the lowest. A maximum content of about 30 per cent sylvite is common to all three members. Insoluble contents increase in successively higher members.Map studies are combined to outline the economic potential of the potash beds in terms of depth to the top of the Prairie Evaporite, ""salt-back"" thicknesses and sylvite grades for each member."

Jan 1, 1971

By Robert B. Wickham

"American Barrick has always balanced its aggressive operating approach with a conservative financial strategy. In fact, what enables their mining team to pursue such aggressive plans with confidence is the conservative financial strategy adhered to by the company. These policies are built on a prudent mix of gold linked financings, equity and gold price hedging.This paper outlines these policies and focusses in particular on American Barrick's gold price hedging program.IntroductionThe company's balance sheet at the end of 1990 clearly shows the wisdom of its conservative policies. Total assets have grown to over US$1 billion; cash has grown to US$312 million and shareholders' equity to US$645 million. All amounts included in this paper are quoted in U.S. dollars. Increased gold production and an effective gold price hedging program also combined to produce record income from operations, earnings and cash flow in 1990.The first half of 1991 is also indicative of the benefits of the company's conservative financial policies. Increasing production, together with its comprehensive gold hedging program, has generated increased earnings, even in a period of falling gold prices.All year-over-year numbers for the first six months are up. Gold production was 36% higher; earnings of $40.2 million $ 0.30 per share - were 46% higher than 1990.Barricks revenue continued to increase despite gold prices remaining unchanged during 1990. Barrick's hedging policy protects the company from falling gold prices on the basis that the upside looks after itself. Their hedging program - including various goldlinked fmancings - enabled Barrick to realize an average price of $437 per ounce of gold sold in 1990, compared with the Comex average gold price for the year of $384 per ounce."

Jan 1, 1991

By Z. Gostynski

The paper is a historical cross-section through a 28-year period of operation of the direct-to-blister Flash Smelting Furnace in the KGHM Glogów Copper Plant. It presents the origin of the furnace as well as the path of numerous changes and modifications both in technology and process introduced in the furnace in response to the production and cost-reduction challenges. The authors provide justification of the statement that continuous improvement of the "Polish" Flash Smelting Furnace has ranked it among the most modem smelting units in the world.

Jan 1, 2007

By Stuart J. Schofield

Introduction The study of the ore deposits of British Columbia is one of fascinating interest not only from a scientific but also from a commercial standpoint and certain wide problems in connection therewith have interested me for some years. Several of these problems have been set forth in papers presented before this Institute on previous occasions. In 1918 it was pointed out that the commercial ore deposits of British Columbia, with one exception, were associated with the granodiorite batholiths of upper Jurassic age. This was followed, in 1922, by a discussion of the ore deposits of British Columbia in which the mineral belts of the province were defined and named, showing a zonal arrangement of ores in which the Pacific coast deposits are characterized by the presence of copper, while the interior belt is marked by the presence of silver, lead, and gold. Methods Of Investigation In reading various reports on the economic geology of British Columbia one is struck with the fact that the mineral veins may be arranged as a system and further examination will show that such a system follows two main directions, one northeasterly and the other northwesterly, both related in origin to the same force.

Jan 1, 1925

By K. J. Brouwer, J. P. Haile

"Construction of the first stage of the tailings disposal facility for the Montana Tunnels Project was completed in October 1986. The project is located 37 km south of Helena, Montana, and involves mining of42 million tons of weathered diatreme are at a rate or 13 500 tpd to produce a gold/silver dore, as well as lead and zinc concentrates. The tailings disposal facility for the project includes a fully drained tailings impoundment for storage of the tailings solids, and a process waterpond for storage of all decanted water prior to recyling to the mill. The over-all facility is designed to achieve the basic objectives ofminimizing seepage to the environment in the short- and longterm, and achieving a fully drained stable tailings mass suitable for immediate reclamation on completion of mining. Specific features of the design include a soil bentonite seal and drainage system within the tailings basin, a free draining embankment with a design flow-through capacity of 4000 US gpm and an ultimate height of 230 ft (70 m), and a soil bentonite lined make-up water pond with a capacity of 420 acre-feet (530 000 m'). The tailings will be discharged in a rotational sequence through multiple spigot offtakes to achieve a thin-layer low energy laminar flow. This 'sub-aerial' deposition results in higher stored densities and maximizes liquid-solid separation on the tailings beaches. The over-all design played a major role in the successful permitting of the project, and was significantly cheaper than a conventional wet disposal system, with overall unit costs for tailings disposal of less than US$0.36 per ton.This paper outlines the site characteristics and the tailings material properties and their influence on the design. Extensive use was made of naturally occurring free draining materials as well as bentonite modified soil liners within the tailings basin, embankment and retention ponds. General construction procedures for the various components are described, as well as on-going construction requirements utilizing materials from the open pit. Finally, the over-all costs and unit costs for tailings disposal are presented."

Jan 1, 1988

By K. Nikkhah, N. Dhadli, G. Freeman

Ammoniacal pressure leaching operations have been in commercial use at the Fort Saskatchewan refinery of Sherritt International Corporation since 1954. Recent improvements have significantly increased the capacity of this circuit. The computer modeling of this process has proved to be a valuable tool in facilitating the evaluation of different operating scenarios in an effective manner. Reagent response in the ammonia leach of nickel and cobalt sulphides is examined using the dynamic process simulation capabilities of IDEAS(TM) software. The dynamic simulation enables accurate measurement of the sensitivity of the process to variables such as temperature, feed rate and ammonia concentration as well as compartmental analysis of metals concentration, pulp density, vent gas composition, and the formation of specific complexes. The complexity of the ammonia leach process makes it a logical choice for evaluation by computational analysis. The methodology for dynamic modeling of a pressure leach process is presented.

Jan 1, 2005

By James S. Redpath

"AbstractThis paper is an attempt. to outline the present status of underground mining contracting in Canada, and to present certain facts concerning the writing and administration of underground mining contracts which, hopefully, may be useful to those intending to engage a mining contractor . The paper is based on the author' s experience as a contractor and also as a consulting engineer advising others in the purchase of contractors' services.HistoryIN THE early days of mining contracting in Canada, the contractor was primarily a labour contractor. He was expected to bring a good crew of men that normally followed him, and to perform certain work under his own direct supervision. The owner usually looked after all other details including financing, payrolls, withholding taxes, etc , computing and paying the contractor his profit. In the pre-World-War II years, most work was done on this basis.Over the years, the contractor was called on to supply more in the way of services, and the present-day situation evolved.Labour contracts are still used, but now the contractor is expected to carry out his own administration. Most contracts now call for the supply of special tooling required to do the work. In most cases, some, if not all, supplies are the contractor 's responsibility and , in a growing number of cases, the contractor is responsible for such items as design and surveying. The ultimate in this direction is the execution of projects on a turnkey basis. Under this system , the contractor carries the project to a stage where it is turned over fully operational to the owner."

Jan 1, 1977

By JAMES E. TILSLEY

Veins at St. Lawrence near the tip of the Burin Peninsula in southeast New/ oundland have been the major Canadian source of fluorspar. Some 2.8 million tonnes were shipped during the period 1933-1977, mostly from five of the more than forty veir.s known. Most of the veins occur in granite. individual veins may be several km in length, comprising a number of mineable lenses up to 760 m long and 25 111 thick. Fluorite content averages about 50 per cent, but may exceed 90 per cent locally. Quartz, calcite, barite and a few sulphides are the other vein constituents. Jn recent years, gravity concentrates were shipped to a flotation plant at Arvida, Quebec, where the fluorspar concentrate was used as a flux in the making of alum in um. Competition f rom Mexican fluorspar was a major factor in the closure of the mines. Ample reserves are available should economic conditions improve.

Jan 1, 1984

By A. Jordens, Y. Zhiyong

"IMBSRE, one of the largest rare earth element (REE) producers in China, produces a rare earth oxide (REO) concentrate as a by-product by floating the middlings stream from a low intensity magnetic separation step in the main iron ore processing stage. As the mine depth has increased, flowsheet changes in the main iron ore circuit have reduced the REO grade and increased the magnetite to REO ratio in the middling product used as flotation feed for the REO circuit. Extensive laboratory work was carried out and identified a new modified hydroxamic acid product, Florrea 8920, that could provide better metallurgical results over the standard hydroxamic acid used as the main collector. This paper briefly reviews the use of hydroxamates in the flotation of oxide minerals, provides detailed information on the different hydroxamates available from Florrea and then provides a case study of the successful implementation of the Florrea 8920 product in a commercial Chinese REE flotation plant. The case study consists of a one year program of pilot plant testing and industrial trials to confirm the results of laboratory tests. The implementation of the new collector resulted in an improvement in grade and recovery to 61% and 64% respectively. The new collector also provided significant economic and environmental benefits.INTRODUCTIONThe flotation of rare earth element (REE) bearing minerals is a topic which has been dominated in the English language literature by the work conducted on the Mountain Pass bastnäsite deposit (Pradip, 1981; Fuerstenau, Pradip, Khan, & Raghavan, 1982; Pradip & Fuerstenau, 1983, 1985, 2013; Fuerstenau & Pradip, 1991; Fuerstenau, Pradip, & Herrera-Urbina, 1992; Herrera-Urbina, Pradip, & Fuerstenau, 2013). By far the most important collector type used for the flotation of rare earth minerals (REM) is hydroxamates. These reagents were initially extensively described as REM collectors in the English literature by Pradip (1981) however they have been successfully applied to numerous other minerals such as: cassiterite (Sreenivas & Padmanabhan, 2002); pyrochlore (Gibson, Kelebek, Aghamirian, & Yu, 2015); hematite, chrysocolla, rhodonite, hubnerite and pyrolusite (Fuerstenau, 2005); and malachite (Lenormand, Salman, & Yoon, 1979) amongst others."

Jan 1, 2016

By S. Kaushik

The control room in a mineral processing plant has become increasingly complicated with complex unit operations coupled with rapidly evolving systems of sensors and control. Even with significant automation, human intervention is required to counter various scenarios that play out every day. A typical control room operator must monitor over 300 individual points of data in order to ensure the safe and efficient operation of the plant. At the same time, the experience of the workforce is decreasing as operators retire and the new generation enters the concentrators. Global competition for skilled operators continues to be strong and the opportunity to apprentice has diminished. The challenge is to provide a skill foundation for the operators so that they can be effective in the concentrator in a timely and safe manner. Progressively, the industry is turning to dynamic simulation tied into the control system. The simulator environment operates behind the control system to emulate the plant operation, reacting as the plant would when a change is made. The operator drives the process, with realistic feedback, which enables learning in a safe environment. This paper will take the reader through a green-field case study and discuss the effectiveness of integrating an operator training simulator (OTS) on the operator’s learning curve.

Jan 1, 2014