Search Documents

By F. Liu, S. Rezaei, M. Muinonen, M. Barati, V. L. Lakshmanan, S. Marcuson

Canadian nickel-copper ore deposits have been a major source of nickel, copper, cobalt and precious metals for more than 100 years. The two main minerals of interest, pentlandite (Pn, (Ni,Fe)9S8) and chalcopyrite (Cp, CuFeS2), are usually accompanied by large quantities of pyrrhotite (Po, Fe1-xS). Until the 1950s, Po containing small amounts of nickel was routinely smelted as part of the valuable Ni concentrate. The rapid growth in Ni demand following the Second World War created impetus to treat the Po separately. This action would liberate a valuable smelting capacity for higher value Pn, allow for recovery of Ni locked in Po, convert the Fe to iron oxide or metallic iron pellets, and recover S as sulphuric acid or elemental sulphur. The roasting process also has the potential to produce energy due to the highly exothermic oxidation of Po. The Ni industry would then have a “waste-free” process. Both Inco (now Vale) and Falconbridge (now Glencore) developed processes and built large industrial plants for this purpose that operated with some success. But technical issues and tenuous economics were continual challenges. By the early 1980s these industrial operations were closed. Sophisticated froth flotation methods of rejecting Po were developed, and Po containing up to 1% Ni became a waste material reporting to the tailings stream. As part of a major study on possible processing methods of Po for both value recovery and waste remediation, this paper presents a historical perspective on Canadian Po tailings with regards to their generation, inventory, value, and attempts to process them.

Jan 1, 2017

"Successive seismic waves may cause progressive weakening of a fault zone, which has been recognized as the mechanism of earthquake aftershocks. However, it is unclear that how a fault zone slips under each wave cycle and how slip displacement accumulates under continuous wave cycles. This laboratory study provides direct evidences on the slip process of a simulated granular fault zone dynamically induced by an incident wave without the effects of late-arriving and reflected waves. The experimental observations show forward and backward slip paths of the fault zone and partially recovered slip displacement after a wave incidence. The unrecovered slip displacement after each wave cycle can be accumulated until it reaches a critical slip distance for seismic faulting, which may reinterpret delayed triggering in earthquake dynamics. The limited interseismic period restricts fault self-healing in strength. The experimental results also indicate that the dynamically induced frictional slip on the fault zone is associated with a complex frictional system, including seismic wave radiation, frictional slip initiation and normal stress vibration. Different from the dynamically induced frictional slip on the fault zone, the statically induced frictional slip causes a permanent increase of slip displacement along the shear loading direction. INTRODUCTIONAn earthquake mainshock may induce aftershocks by suddenly changing external stresses applied to another fault zone in the near field (Kilb et al., 2000) and by slightly perturbing a fault zone from a critical steady state to stick-slip faulting in the far field (Gomberg and Davis, 1996). The dynamically induced frictional slip on a fault zone has been recognized as the mechanism of earthquake aftershocks (Marsan and Lengliné, 2008; van der Elst and Brodsky, 2010). Although earthquake aftershocks have been extensively studied by many seismological methods, a simplified laboratory fault zone can provide possible interpretation on real faulting and detailed analysis on a friction process (Dieterich, 1979; Nielsen at al., 2010). According to a few laboratory experiments related to the dynamically induced frictional slip on a simulated fault zone (e.g., Uenishi et al., 1999; Johnson et al., 2012), the slip process induced by successive seismic waves exhibits continuous motions. However, it is unclear that fault slip response under each wave cycle and slip displacement accumulation under continuous wave cycles."

Jan 1, 2015

By J. H. Starkey

Large differences between macro and micro grindability relationships have been discovered for mill design measurements using the patented SAGDesign(TM) test. Crushing, Rod and Ball Mill Wi tests, and breakage parameter measurements have previously been used to design SAG mills but have not revealed the true magnitude of these differences. A SAGDesign(TM) test measures the SAG/Bond Wi Ratio (defined below) for every sample tested and gives a good design result because the F80 of the SAG stage test feed is 19 mm and because the test includes a Bond Ball Mill Work Index on SAG ground ore. Good flotation operation demands properly sized grinding mills and steady feed to the flotation circuit.

Jan 1, 2009

By Frank Doxley

"FIRST OF ALL I should like to express to the members my sincere thanks for having had the privilege of serving them as President during the year now ending, to the Council for their guidance, and to the Secretary-Treasurer for his untiring efforts on both the Society's and my behalf during my year of office.During the .past five years the Canadian •Coal picture has changed considerably. In the West, production has been almost halved and many mines have been closed, due to the development and expansion of oil and natural gas industries, which, with some imported residual oil -on the Pacific coast -have provided competition which has been impossible to meet. The two major railway companies have embarked on an oil-burning and dieselization .programme and with this has .been lost one of the largest available markets for coal. Natural gas pipe-line installations still further threaten the remaining outlets for Western coal.In the East, retention of markets has also been a •problem, due to the intense competition provided by imported American •coal and the importation of residual oil.Because of cost it is impossible for central industrial Canada to be supplied with .coal from the Maritimes and markets are, therefore, restricted to fringe areas in Ontario and Quebec, and the Maritime Provinces.The dieselization programme of the Canadian National Rail ways has meant the loss of a large market for Nova Scotian coal and it is fair to assume that within a comparatively short time the market will be completely lost."

Jan 1, 1955

By Greg Gosson

"Early efforts to develop formal reporting systems to quantify and classify mineral deposits date back over 100 years. (e.g. Hoover 1909: “Proved, Probable, Prospective Ore”). This was at first driven by mine operators’ need for reliable estimates of what their mines could produce. Disruption of transportation routes by world wars prompted western governments to recognize the need for assessments of strategic sources of metals and minerals that could support domestic industry during times of crisis. Categories were created to quantify mineral potential which were additional to those of mine reserves. Terms such as hypothetical and undiscovered resources entered the lexicon. Capital markets serving the mining industry were traumatized during the latter part of the 20th century by undisciplined and fraudulent disclosure by exploration companies of mineral deposit potential. Government securities regulators pressed for the development of credible reporting codes (e.g. SEC Industry Guide 7: 1981; JORC 1989; SAMREC 1994, CIM 2000). Representative organizations from the major western mining countries generally agreed that there should only be three categories of mineral resources (measured, indicated, and inferred) and two categories of mineral reserves (proven and probable). This was formalized in 1997 with the “Denver Accord”. Acceptance of the standard terminology may have been the easy part, because the challenge for the 21st century is to get general industry acceptance and agreement of the principles behind the definitions of each category. There has been noticeable movement towards this objective in the last few years. This is reflected in part in the updated reporting codes by JORC 2004, CIM 2005; SAMREC 2007; SME 2007; and PERC 2008, and the development of the CRIRSCO International Reporting Template 2007."

Jan 1, 2003

By Jon Errey, Aleksandar Petrovic, Karl Haase

"Developing a gold deposit of this magnitude in the Amazonian jungle of Guyana posed many challenges. This paper describes not only the process & logistical challenges arising from the remote mine site location in a tropical environment with a local industry unaccustomed to recent large scale gold mining operations, but also the innovative technical solutions employed to address the unique ore body characteristics. The best examples of this approach were dealing with the initial high clay content saprolite ore from the development phase and primary mining pits whilst ensuring that the design also implemented the right method to deal with the future fresh rock in an environmentally sensitive habitat. In order to do this separate individual crushing flowsheets were generated, focusing on the specific material handling equipment that would be suitable to handle these various types of material and ensure high recoveries were maintained.INTRODUCTIONAurora gold mine is located in forested region of Guyana, 170 km west of capital Georgetown, and 130 km West North-West of Bartica, a settlement at the junction of the Essequibo and Cuyuni Rivers.The Aurora gold project (Aurora) is a 5,000 tonne per day open-pit/underground operation, which will produce a total of 3.29 million oz. gold – averaging 194,000 oz. per year – over an initial 17 year mine life. At the final investment decision in 2014 Aurora had a total resource of 6.54 million ounces in the measured and indicated categories (62.83 million tonnes at 3.24 g/t Au) as well as additional 1.82 million ounces in the inferred category (16.93 million tonnes at 3.34 g/t Au)."

Jan 1, 2016

By R. W. Pauls

"Many tens of thousands of hectares of forested land will be disturbed and reclaimed in the surface mineable Athabasca oil sands area during the next few decades. The surface area disturbed by Syncrude’s Mildred Lake development alone exceeds 10 000 ha to date. It is not clear that reforestation of disturbed areas will best accommodate the aspirations of all stakeholders, particularly traditional users of the land. A five-year research program by Syncrude Canada Limited and the Fort McKay First Nations has examined the feasibility of raising bison on land reclaimed after disturbance by oil sands development. Forage productivity and carrying capacity for bison was comparable to that of grasslands elsewhere in Alberta. Concerns regarding compaction of newly rebuilt soil by bison traffic proved unfounded. Bison demonstrated weight gains typical for ranched bison and calving rates averaged 90%, a value typical for ranched bison. The animal husbandry problems encountered were typical of those occurring on bison ranches elsewhere in Alberta. An economic analysis indicates that a 1000 ha bison ranch on reclaimed land has a net present value that compares very favourably with a similar area supporting commercial forest. Subject to approval by Alberta Environmental Protection, the current research project will be expanded as a pilot commercial ranching venture in order to explore its commercial viability as a business venture by the Fort McKay First Nations. At the same time, measures will be implemented to resolve various regulatory issues associated with commercial bison production in the oil sands area.BackgroundSyncrude Canada Ltd. (Syncrude) is proposing, in its land reclamation strategy, a feature that is, depending on one’s background and perspective, regarded as an innovative approach to land reclamation, a threat to the regional forest industry, a creative response to aboriginal stakeholder concerns, a reneging on reclamation commitments, an opportunity to provide an ongoing economic base for postoil sands regional economy, or an environmentally unsound use of the land. These diverse and sometimes strong reactions have been generated by the proposal to introduce bison, either free-ranging or commercial ranched, to the reclaimed landscape."

Jan 1, 1999

By M. Ataka

Magnesium alloys are not easy to plastically deform at room temperature and may suffer from edge cracking at high reductions, especially during sheet rolling. In this study, the authors attempted to improve the rollability by the low-temperature hot rolling method, in which the rolling temperature range is lower than that of hot rolling, and also by the edge-heating method, which locally heats sheet edges.

Jan 1, 2006

By A. C. Stevenson

"There are many critical application issues that affect all AC drives, but there are several that are absolutely mandatory for pulse width modulated (PWM) AC drives. If these rules are not followed, the drive system will have insulation, bearing EMI or noise problems. Pulse Width Output VoltageFigure 1 shows the output current of a typical pulse width modulated (PWM) drive. This is, of course, not a clean sine wave thus will have a lot of very significant harmonics. In fact, the harmonic spectrum is directly related to multiples of the carrier switching frequency plus side bands related to the basic output frequency. A typical spectrum for a PWM source bridge switching at 5 kHz is shown in Figure 2. Notice that the spectrum has multiples of the 5 kHz switching frequency and the number of side bands gets larger as the harmonic number increases.IGBT Switching TransientsWhenever we have PWM inverter switching, voltage transients are formed that propagate (usually at about half the speed of light) down the power cables to the motor just like in a radio frequency transmission line. If we do not terminate these transmission lines (motor cables) properly, the voltage pulses will be reflected when they reach the motor end and will be transiently increased up to twice their original amplitude.This transient voltage rise, shown in Figure 3, is important for three reasons:1. Insulation Voltage Stress — Higher voltage stress in the motor connecting cables and motor insulation will lead to a shorter insulation lifetime. If any of the voltage transient peaks exceed the insulation corona discharge level (partial discharge level), the insulation will gradually degrade with each voltage pulse. When it has been sufficiently degraded, it will then fail.Most new “inverter rated” motors have triple layer insulation which has a 1600 to 2000 volt partial discharge level. This will make them suitable to withstand the double voltage peak transient from a 600 volt inverter. It is wise to make sure of this fact, since a “standard” induction motor will only withstand about 1200 volts. Use of a standard motor in this application would shorten its life drastically. This can sometimes be as little as a matter of hours."

Jan 1, 2000

By J. A. Finch

Solvent-coated air bubbles in the Air-Assisted Solvent Extraction (AASX) process achieve the dual role of high solvent specific surface area and ease of phase separation. The thickness of the solvent film is of fundamental interest but difficult to measure directly in the process itself. As an approach interferometry (in the UV-vis region) was used to measure the time dependent thickness of a film formed by blowing an air bubble in kerosene-based solvents. The film was stabilized by the presence of 1.5 ppm silicone oil, as employed in AASX. The film appears to comprise two layers; an outer "free" layer of almost constant thickness and an inner "bound" layer which decreased in thickness with time. The bound layer is considered relevant to AASX. For a 20 mm diameter bubble blown in LIX/kerosene solvent the initial thickness was ~ 3 um which decreased over 10 minutes to a final rupture thickness of 500 nm. The bound layer thickness and time to rupture decreased with decreasing bubble size. Correspondence to prior indirect estimates of solvent layer thickness is examined.

Jan 1, 2006

By M. Tardif, F. L. -Lavoie, M. Ruel

"In mineral processing, it is often very difficult to reliably measure several key operation variables. The harsh environment and high temperature encountered in pyrometallurgy processes lead to some difficulties when selecting the instruments, valves and actuators. If an important variable cannot be measured or manipulated adequately, controlling it can really become a big challenge. Sometimes, it is simply impossible to find the perfect equipment for the task. To help overcome these difficulties, a different approach is required. This approach will not correct the inherent problems related to the instruments and valves, but will cope with these problems. This article will demonstrate how modern process control techniques can be used to solve complex problems while remaining easy to implement. In this article we will described how soft sensors and multivariable fuzzy logic control were implemented at Koniambo Nickel to stabilize the furnace feed and allow for safe and reliable operation of an 80 MW DC arc furnace.INTRODUCTION Process Overview The process plant at Koniambo Nickel SAS is located in the North Province of New Caledonia, 310 km north of Noumea. The nickel-bearing ore is mined in the nearby Koniambo massif. After being screened and crushed, the ore is transported to the processing plant using a 12 km conveyor. After stacking in two blending piles, the ore, containing 2.3% nickel, is fed to the processing plant where it will go through the NST process (Nickel Smelting Technology) before being sent to refining and shotting. This article will focus on the improvement to control of the NST processes. The first steps of this process consist of milling the ore and removing all moisture through calcining (Figure 1)."

Jan 1, 2017

By Robert B. Parsons

"Thrashing one's way through a jungle of entangled tax rules is no easy task today, as Canada's legislators continue to complicate this country's income tax laws. At some magical point, there is presumably some balance to be struck between legislation which is equitable and unambiguous on the one hand, and at the same time is efficiently complied with and administered. It is becoming increasingly clear that the legislation is not in balance, and that there is a pressing need for some simplification of the income tax rules and regulations especially in areas of critical importance to the resource industries-even though such simplification will likely involve some sacrifice of equity and certainty.Introduction""I would wish that ... the superfluous and tedious statutes were brought into one sum together, and made more plain and short, to the intent that men might better understand them."" Edward VI, King of England 1547-1553.Regal decree notwithstanding, the legislation of most developed nations continues to become more complex, lengthy, and confusing than ever before. Canada's income tax system cannot escape the accusatory finger pointing at examples of this serious problem which plagues all of us today.Although many areas of our tax law could easily warrant some degree of simplification, for those who are involved with this country's resource sector, that horrendous, almost unreadable, part of our tax legislation which deals with resource taxation must be regarded s a prime candidate for simplification. In recent decades, but particularly in the past ten years since tax reform in 1972, budget after budget, both federal and provincial, have amended, massaged, modified, and manipulated the resource tax rules to the point where not only are taxpayers totally lost in their attempts to make some sense of the entanglement of rules, but also the draftsmen themselves acknowledge that the outer limits of complexity are being reached, and that the whole set of rules is on the verge of grinding to a groaning halt under its own weight of nonsense and frustration."

Jan 1, 1982

By Guadalupe Sanchez, Roel Cruz, Sergio Castro, Claudia Beltrán, Isabel Lázaro

The recovery of zinc in refineries is strongly affected by the formation of zinc ferrites during the roasting of zinc concentrates. To achieve the highest zinc recovery most of these plants operate under high acidity and high temperature conditions in their leaching circuits. However, under these conditions high iron dissolution occurs. For iron control the common practice is to precipitate it as jarosite, and calcine is normally used as neutralizing agent. This practice causes a significant loss of metal values associated with the calcine, such as zinc ferrites and silver insoluble phases. These metal values are carried by the jarosite into confined waste in many plants. In order to diminish such losses, it is necessary to use a neutralizing agent that could substitute the use of calcine. An alternative neutralizing could be the basic zinc sulfate (BZnS). This work presents the results of a laboratory analysis on the required conditions for the BZnS production from process streams of a zinc refinery plant. Neutralizing behavior of BZnS was evaluated in iron precipitation as jarosite, in order to establish the feasibility of replacing the calcine and decrease the loss of zinc and other metals values during the iron removing step of the hydrometallurgical circuit of the zinc refinery under study.

Jan 1, 2014

By Julian Baldry

"This paper begins by describing the parameters of high-speed underground tracked drifting operations and the mucking cycle, and-discusses their variations. The railbound Haggloader 8HR is then described, as well as the Hagglund shuttle trains, outlining the advantages and disadvantages of the system. A comparison with conventional mucking operations is then given.IntroductionDrift and tunnel rounds are mucked by one of two major methods, either trackless with diesel loaders and trucks or with track loaders and cars. The aim of this paper is to compare the conventional tracked mucking cycle with the Hagglunds system alternatives.For many years, the traditional method of attacking the mucking cycle has been with a rocker shovel loader, a string of cars and a locomotive. The rocker shovel loads the first car and when full it is taken to a side drift, cherry picker or some other transfer point and is exchanged for an empty one. This empty car is then pushed back into the face and the loading continues until all cars are full . Then the whole train is taken out to a dump point where the cars are emptied. Normally the train's capacity is less than the volume of the muckpile, so the cars go back to the face. This loading cycle is repeated until all muck is removed from the heading. The last train out from the heading usually takes the loader and parks it in a side drift before continuing on to the dump where the cars are emptied.This simplified version of the traditional loading cycle excludes the ancillary work elements such as track laying and so on, but does point out that the cars must be transferred when full and that the whole train normally makes at least two round trips from the dump to the face. The prime aim in drifting is to cycle a round whithin a working shift which necessitates that no one part absorbs so much time as to prevent the completion of the cycle.Mucking, drilling and loading and the ancillary work such as rock bolting, vent and service pipe hanging typically each take one-third of the available work time. Drilling or mucking can and often do, because of various factors, take nearly half of the total cycle time. Once any segment of the operation starts to take this portion of the shift, the likelihood of missed rounds becomes increasingly greater."

Jan 1, 1981

By Michael Boyle, John Zeni

"The Blind shaft boring method is a mechanised process of excavating large diameter vertical shafts downward from the surface. It is a rotary drilling technique eliminating any requirement for personnel to enter the shaft or access underground workings during drilling and lining phases. Excavated material is delivered to surface carried by a flow of circulating fluid through the centre of drill rods. The drill assembly is suspended from a large A-frame rig and powerful winch at ground level providing vertical thrust to a hard rock cutter head. INTRODUCTION The Southern Coalfields Ventilation Shaft was constructed at a mine, 45 km north-west of Wollongong. The 5 m finished diameter (6.2 m drilled) shaft reaches a final drilled depth of 517 m, the deepest, fully lined blind bored vent shaft to date in Australia. Operated by a mining company in the Southern Coalfields, the expanding mine required a new ventilation shaft and associated surface infrastructure to service future operations. An assessment of future ventilation requirements for the coal seam operations identified a need to improve the capacity and reliability of the existing underground ventilation system in order to ensure a safe and efficient underground working environment. Installation of the new upcast ventilation shaft was determined to be the most cost effective and reliable solution to provide adequate ventilation for underground operations. The completed shaft is smooth and fully lined with steel/concrete composite liners that are hydrostatically sealed. The shaft lining is designed to meet the mine ventilation requirements for a service life of 20 years. The shaft intersects the top of the working section of the coal seam at approximately 513 m of depth. This includes the shaft collar depth and shaft bottom profiled intake section.PROJECT METHODOLOGY AND INDUSTRY BEST PRACTICE The shaft was drilled using the blind bore method, an innovative construction technique and an alternative to the traditional methods of sinking deep and large diameter shafts, such as raise boring and conventional drill and blast shaft sinking. The blind bore method allows the shaft to be drilled from the surface down without anyone having to enter the shaft or the mine during the construction process. This is by far the safest method of shaft construction and is especially suitable for difficult ground conditions where there may be unstable or water-charged strata. As this method involves drilling from the surface downward, shafts can be completed ahead of the underground mine development. Thus, allowing underground operations to focus on development and production without the conflicts of managing ventilation priority for underground contractors and mucking out spoil from excavation workings."

Jan 1, 2019

By K. G. Chipman

THE discussion on Dr. Chipman's paper, Mapping by the Topographical Survey, centred mainly on the urgent need for aerial photographic reconnaissance of unmapped portions of the country as an initial phase in the provision of suitable topographical maps for use as a guide in geological mapping, prospecting, exploration, and development work in the areas concerned. This, ir was pointed out, would necessitate an expansion of the topographical work of the Bureau of Topography to keep pace with the photographid work and to meet the demand for maps for use by geologists of the Bureau of Geology and others. A resolution requesting Institute Council to make representations to the proper authorities, urging that aerial photography and topographic map-ping be greatly expanded to meet the pressing needs of the situation, was moved by DR. W. F. JAMES and seconded by MR. L. G. SMITH, and carried unanimously. The full text of the resolution appeared on page 221 of the May BULLETIN. Others who spoke in support of the resolution were MESSRS. E. S. MOORE, L. B. ROCHESTER, F. D. SHEPHERD, and W. J. WRIGHT. Dr. Hansen then presented his paper, Mapping by the Geological Survey, discussion on which is summarized below. MR. FRANK EBBUTT(l) spoke of the very valuable service the Geological Survey bas rendered the mineral industry, and indeed the whole nation, in its century of existence, despite the very inadequate financial support it has received. Now, more than ever before, a strong and expanded Geological Survey is essential if the Industry is to continue to prosper. Our known ore reserves are being depleted very rapidly, and we are finding no new orebodies to take their place. As an aid in prospecting and exploration, and also in the development of orebodies when they have been found, we must have geological maps of the vast sections of the country which at present are unmapped or inadequately mapped. The Institute should make every endeavour to have the Geological Survey strengthened so that such maps may be made available as soon as possible.

Jan 1, 1944

By D. Hu, L. Matzar, J. Hampton, M. Gutierrez

Nanodarcy permeability is common in many oil- and gas-bearing formations requiring unconventional stimulation technologies, such as hydraulic fracturing (HF), which can connect the isolated hydrocarbon-rich pores with a wellbore through induced fracture networks. Even though a dense induced fracture network is capable of accessing economic amounts of hydrocarbons, much of the rock between and very close to the fracture network is still un-accessed and contains extremely low permeability. Inducing fracture networks into brittle rock can create large amounts of micro failures in surrounding regions that are not connected to the wellbore, as can be seen in Fig. 1(a) from the very wide acoustic emissions (AEs) cloud associated with a narrow fracture generation. It is possible in certain types of rock to increase the effective matrix permeability in localized regions based on the damage associated with the surrounding hydraulic fractures and subsequent high stress concentrations along localized pre-existing potential failure zones. To study this problem, laboratory HF tests were performed at true-triaxial stress state in brittle crystalline rock while monitoring AEs. The AE associated with HF was analyzed for source parameters using the moment tensor inversion method called Simplified Green’s Functions for Moment Tensor Analysis (SiGMA). Using the moment tensor for each individual AE event, the mode of failure was determined. Crack slip directions and crack face normal directions were also found, along with the relative volume of individual micro failures as well as a damage parameter. The associated source parameters were used to classify differing regions of damage in the sample induced from HF and correlate these regions of differing damage to the effective drainage region. Shown in Fig. 1(b) is a near-wellbore (NWB) region that contained three times larger average relative volumetric deformation of individual tensile AE events than the average tensile AE event volume from the entire sample. Because of the large difference in micro fracture volumetric deformation for the NWB region compared to the entire sample, predictions of HF induced damage must be included in reservoir drainage predictions.

Jan 1, 2015

The Cooperative Research Centre for Mining Technology and Equipment (CMTE) is funded by the Commonwealth Government, by its mining research members Ñ the Universities of Queensland and Sydney and the CSIRO1, and by its industry members Ñ BHP Coal, RioTinto R&TD, Hamersley Iron, Mining Technologies Australia, Pasminco, Shell Coal, WMC Resources, Advanced Mining Technologies, and Aberfoyle. The Centre conducts work aimed at improving the competitiveness of the Australian mining industry. The current work is focused in four areas: new mining and drilling systems, geological sensing, automation, and equipment maintenance and reliability. This paper describes much of the work in these program areas that relates to metalliferous mining.

Jan 1, 2001

By Malcolm Black

Introduction Before beginning to write this paper, I decided that I should first find suitable definitions of the words Sample and Sampling. The dictionary gives: "Sample.-A portion indicative of the whole"; and according to Baillie (1), sampling is "That process whereby a representative and comparatively small portion of material is selected from a large bulk, and preserved under such conditions as shall prevent contamination or avoidable alteration, with a view to the formation of valid conclusions regarding the suitability of the bulk for specified purposes". These comprehensive definitions are alike in substance, and indicate that unless a truly representative portion is taken, it is not a sample. Ore 'as mined' generally varies a good deal in composition, and, in crushing, segregation takes place. Some of the minerals present, due to differences in hardness and friability, break into smaller pieces than others, and, on reaching the bin, the coarse particles roll away, leaving the fines behind. The result of this segregation is generally quite noticeable on the conveyor feeding the mill, especially when the bin is nearly empty and the crushing plant shut down. Should the sampling period synchronize with either the coarse or the fines, the sample obviously would not be representative. I agree that this is rather far fetched, but I maintain that such a condition is possible. Assuming that a representative sample may be procured from the feed conveyor, the method of cutting it down for assay has considerable influence in maintaining the original condition of the sample. The finer the material is ground after each cut, the more uniform the sample will remain. To illustrate this point, let us take a quantity of fine sand and add, say, three grains of rice to represent metallic particles. We may mix this sample by any of the known methods, then cut it into four equal portions. It is obvious that at least one of the portions will be without a rice grain. But let us grind the three grains of rice into flour and proceed as before. Now there will be a much greater chance of including some of the rice in each portion.

Jan 1, 1935

By M. Meratian

The in-situ methods have been developed in production of aluminum matrix composites. A commonly adopted in-situ method involves reaction between a metal oxide and aluminum to produce alumina particles or whisker reinforcements. Aluminum-alumina particle composite was fabricated by in-situ method where alumina particles were produced from reduction of copper and silicon oxides by melting and casting aluminum. Aluminum matrix composites reinforced by Copper and Silicon alloying elements and alumina particles have been obtained. The size and shape of alumina particles were studied by scanning electron microscopy (SEM). The size of alumina obtained from mixture of SiO2 and CuO was bigger than the alumina particles obtained from CuO.

Jan 1, 2007