Search Documents

By Noel Brien, O&apos

General: National Asbestos Mines Limited has operated an asbestos mine and mill near Thetford Mines, Quebec, since 1958. As a result of additional exploration of the orebody in 1962-63, it became apparent that long-range mining plans would have to be revised to allow for a large increase in both ore and waste tonnages. It was decided that the task of checking out possible mine designs could best be analyzed by a computer to obtain data from which an optimum open-pit configuration could be plotted. Object: It was desired to arrive at an optimum open-pit configuration with an over-all pit slope of 45 degrees and a minimum operational width of 200 ft. at the bottom. Calculations were based on assay values from diamond drill holes in cross sections of the mine. The computer's assignment was to select and describe, by coordinates, the optimum cross section for the mine. Mine engineers then assembled the various optimum sections to produce the pit outline. As this would not necessarily result in a practical mining arrangement, the computer also provided alternate solutions,

Jan 1, 1965

By J. De Geoffroy, T. K. Wignall

The paper describes a statistical method based on regression and classification analysis which is designed to assist exploration management in the selection of prospecting areas and drilling targets in regional programs. The classification is based on three criteria which are formulated from sets of relevant geological, geophysical and geochemical factors: (a) regression estimates of expected ore values, (b) Bayesian probabilities of success and (c) expected utility payoffs. The advantages of the method are: (a) rational and unbiased ratings for areas or targets in a manner consistent with management's goals; (b) calculation of probabilities of success and confidence intervals for the ratings, and (c) rapid and accurate handling of a large amount of data by computer programs.

Jan 1, 1970

By A. Golpaygan

Application of Computational Fluid Dynamics (CFD) modeling for simulation of fluid flow and combustion in industrial scale electric furnace is presented. Poor combustion efficiency, roof and/or side wall overheating, carry over to off-gas system and non-ideal radiative heat transfer to processes or cooling systems have been common limiting factors causing inadequate process performance of the furnace, operational problems, and safety hazards. This paper describes how CFD analysis can be used to obtain a better understanding of commonly observed problems associated with freeboard combustion. Examples are presented to describe using combustion CFD modeling to understand requirements to diagnose a problem with furnace design including required freeboard volume or possible roof/side wall overheating.

Jan 1, 2011

By Ralph Harris, Javier Jara

"Oxygen is essential in gold cyanidation. It is supplied to the leaching media by sparging oxygen or compressed air into the cyanidation tank. The rate of oxygen transfer is critical to achieve the desired oxygen concentration in solution.The performance of a novel device for gas sparging recently developed at McGill University is compared to the mass transfer characteristics of the two spargers most used in the gold industry: the four lance configuration and the inverted cone. The distribution of gas and the kinetics of oxygen desorption of the three types of spargers was studied in a 140 litre tank. The oxygen dissolution of the new device is three to five times faster than the other spargers. This could increase the leaching rate and/or decrease the cyanide and oxygen consumption.IntroductionIn hydrometallurgical processing, it is often necessary to bubble gas through a pulp to carry out the wanted reactions. The gas can act to agitate the pulp and it can also supply reactant. The rates of the reactions which require a reactant supplied by the gas are often dependent on the rates of mass transfer from the gas to the solution.A common example of this is gold cyanidation which requires oxygen for gold dissolution. Since the gold containing slurry is rich in other oxygen consuming substances (sulphide like pyrrhotite), it is important to provide enough oxygen to allow complete gold dissolution within the residence time of the cyanidation reactors. It has been demonstrated that the rate of gold dissolution is directly proportional to the dissolved oxygen concentration of the pulp which in turn is proportional to the oxygen partial pressure in the bubble 1 2 3. Improving the rate of mass transfer of oxygen increases the dissolved oxygen concentration of the slurry and therefore improves the rate of the reaction.The rate of mass transfer from a bubble to its surrounding solution increases with decreasing bubble size and increasing gas bubble residence time which in turn increases with decreasing bubble size. The generation and dispersion of small bubbles is thus critical to achieving high rates of mass transfer. Different configurations and devices used to inject gas have different effects on the bubble size and the residence time, influencing the overall rate of mass transfer. Therefore better mass transfer can be achieved by adopting a more efficient method.The methods tested in this report are the four lance configuration (wall spargers), the inverted cone and a new device, designated HCD. The wall spargers and the inverted cone are used widely in the industry today."

Jan 1, 1994

By R. T. Erskine

"The No. 6 orebody is located 6 miles from the main op.eration of Brunswick Mining and Smelting Corporation Limited and includes open-pit and primary gyratory crushing facilities. Ore is transferred by truck to the secondary crushing facility at the main plant. About 3,500 tons of ore per day are crushed to minus % in. and ground to 68 per cent minus 400 mesh in rod and ball mills for flotation feed. Conditioning and aeration precede rougher flotation, and four stages of cleaning bring concentrates to a grade of 42 per cent Pb + Zn + Cu. Middling products are reground and refloated in a secondary flotation circuit, producing a cleaner feed and a final tails product. Primary bulk concentrate is treated with sulphur dioxide and steam-heated to l 70°F and the majority of the gangue is floated off, leaving a product that assays 57 per cent combined Pb + Zn + Cu and is suitable for marketing. This material is thickened, filtered, dried and loaded into railway cars for shipment to the smelter. Reagent use on flotation is conventional, with many compromises in dosage required to maintain the recovery of lead and zinc in the most advantageous proportions. Many refinements in the flowsheet have been made since start-up in 1966, and more may be made as laboratory and plant testwork indicate possible improvements."

Jan 1, 1971

By Ainul Akhtar, Steve Cockcroft, Jixiang Xu, Daan Maijer, Lu Yao

"Nitrogen rich Ti-N inclusions are one of the more difficult inclusions to remove during liquid metal refining of titanium. If present in the final component, they can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading. Understanding the kinetics of dissolution of Ti-N particles during consolidation/melting of titanium can help us better operate and design the melting processes to minimize their occurrence in Premium Quality Titanium production. A numerical model based on finite difference method has been developed to calculate the dissolution of a spherical Ti-N particles in molten titanium. Analytical solutions were used to verify the finite difference code for calculation of concentration profile and the dissolution of spherical solids. Taking into account the limitations in these approaches for the different cases examined, the invariant field approximation showed good agreement with the results from the numerical analysis. Evolution of the size of a spherical Ti-N particle during dissolution was predicted by the numerical model and the particle dissolves in 163 s.INTRODUCTION Properties like low density, high specific strength and excellent corrosion resistance make titanium attractive for a variety of applications. Key characteristics in the processing of titanium and its alloys include its high sensitivity to impurities, especially atmospheric oxygen and nitrogen and its high reactivity in the molten state. Nitrogen rich inclusions Ti-N, also known as Type ? or hard alpha defects, usually have substantially higher hardness and lower ductility than the surrounding material. Because they can act as fatigue initiation sites, Ti-N inclusions can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading, even in minor amounts (tenth of a percent) (Lampman, 1990; Moiseyev, 2005; Lütjering & Williams, 2007). Ti-N encompasses as a broad range of nitrogen contents from a few wt% up to stoichiometric TiN. The liquidus temperature of Ti-N titanium increases substantially with increasing nitrogen content. Consequently, depending on the concentration of nitrogen, the melting point of Ti-N inclusions can be above bulk liquid metal temperatures during melt processing. Thus, removal of Ti-N defects hinges on dissolution and not melting."

Jan 1, 2017

By Y. Chengxian, F. Yaorong, Xinzhe. L.

Many factors about the HIC (hydrogen-induced cracking) resistance of pipelines are discussed in this paper. The main factors that influence the ability of HIC are environmental and material factors. The chemical compositions, non-metal inclusions and microstructure are discussed in detail, while a group of tests on HIC resistance are done according to varying C, S, Mn and P contents in pipeline steels, different experiment time and different strength to the coupon. It is concluded that decreasing the amount of C and S can obtain good HIC resistance; the test time has an effect on the different microstructure of X70; microstructure is the most sensitive factor for the initiation processes of HIC.

Jan 1, 2005

By J. Worden, D. Hughes, S. Smart, H. Zughbi

The enterprise wide optimization (EWO) of steelmaking and manufacturing is a multi-level, hierarchical problem which spans higher level corporate planning and scheduling through to the lower level operations of processes that produce and manufacture steel. External and internal system dynamics combined with process unit co-ordination create complex changing circumstances for the enterprise. This paper presents a scoping study as a prelude to enterprise wide considerations at an integrated steelworks to help inform the choice of appropriate model types and optimization techniques. The hierarchical, multi-level structure of the enterprise and the important spatial-temporal scales to consider are defined. Insights into the system were gained by analyzing a large set of dynamic operational data. Over two years of data were subject to both univariate and multivariate analysis with the intent of understanding the complex interrelations of energy flows on site, the inherent system dynamics of the energy network, system operational modes, aspects of planning and scheduling and the coordination between major processing units. This analysis was further used to evaluate the performance of the system in regards to energy utilization and understand the potential economic benefits derived from improved operational decisions.

Jan 1, 2015

By L. Tafaghodi, A. Hosseinpour

"Silicon is considered as the most appropriate semiconductor material for manufacturing solar cells because of its natural abundance and being nontoxic. The transferable knowledge and technology from the electronics industry and the long history of silicon-based semiconductors are also assisting the domination of silicon as the most common semiconductor material. Developing an environmentally and economically viable process for producing solar grade silicon has been one of the main challenges in the silicon industry in the past few years. Metallurgical refining processes have received significant attention because of their high productivity and low cost. Slag refining is one of the purification methods which is based on oxidation of the impurity elements, followed by its dissolution into a slag phase. This article presents a review of various slag refining processes that have been employed for purification of silicon and silicon alloys. SiO2, CaO, CaF2, CaCl2, Al2O3, MgO and Na2O are the major components of the slags used for silicon refining. These slags can be classified into three main categories including binary, ternary and quaternary slags.INTRODUCTION Silicon can be categorized into three different grades based on its application or purity: metallurgical grade silicon (MG-Si) with purity of ~98 %, solar grade silicon (SoG-Si) with purity of ~99.99999 % and semiconductor grade silicon (SeG-Si) which has the purity of 99.9999999 % (Johnston & Barati, 2010; Krystad, Tang, & Tranell, 2012; Tang, Øvrelid, Tranell, & Tangstad, 2009). Producing SeG-Si is carried out through an energy-intensive and complicated process named Siemens. This purification process is relatively slow and involves using toxic and corrosive reagents (e.g. Trichlorosilane). At present the majority of SoG-Si is produced via Siemens or Siemens-like processes and there is very limited production via processes dedicated to SoG-Si. Because of the difference in silicon specifications required in microelectronics and photovoltaic industry, and the cost and energy associated with the Siemens process, an interest has emerged to develop technologies dedicated to producing low cost SoG-Si (Istratov et al., 2003; Johnston, Khajavi, Li, Sokhanvaran, & Barati, 2012; Mitrašinovic, D'Souza, & Utigard, 2012; Wu et al., 2012)."

Jan 1, 2017

ABSTRACT The inevitable uncertainty in modelling spatial variables decreases as more data become available. This reduction depends on the properties of the variable being modelled. Spatially continuous variables show less uncertainty for a given spacing than erratic variables. A geostatistical simulation based approach is developed to quantify the relationship between uncertainty and data spacing. Reference realizations are sampled to condition additional realizations and quantify uncertainty. The procedure is automated, making it straightforward to consider sensitivity and different geological domains. A case study of the relationship between uncertainty and data spacing for net oil sands thickness data from northern Alberta is presented. _ KEYWORDS Simulation, Sampling,

Jan 1, 2013

By M. Yao, D. Thibodeau

"Selective mining, such as post pillar cut and fill, is used in large, flat, irregularly shaped ore bodies where ground stability is to be maintained. This selective mining is used to open the stope to the full lateral extent of the ore body in order to minimize the dilution and maximise the recovery. For increased mining depth, design of the post pillar becomes more challenging since those pillars will eventually fail as mining progresses upwards. The post pillar should be designed such that failure does not occur at the early mining stage, such as at the first cut. After mining progresses upwards, the post pillars are expected to fail but be confined by backfill. In order to maximise ore recovery, both drift width and post pillar size must be designed adequately with a consideration of all geomechanic parameters. This paper will describe the process used to design post-pillar cut and fill for one of the ore bodies in Vale’s Copper Cliff Mine using a combination of both empirical deterministic and numerical modelling techniques. By utilizing both empirical deterministic and numerical modelling techniques drift width and post pillar size can be effectively designed. Current post pillar cut and fill design in the existing Vale operations are used to validate the design for Copper Cliff Mine. INTRODUCTIONCopper Cliff Mine is located within the Copper Cliff Offset in the limits of City of Greater Sudbury, Ontario, Canada, as shown in Figure 1. The Copper Cliff Offset extends about eight kilometres south from the Sudbury Igneous Complex into the footwall rocks. Until 2008, the current Copper Cliff Mine was operated as two separate mines i.e. North Mine and South Mine. However, as part of restructuring of Vale Ontario Operations, the North and South Mines were merged in 2009 to form the “Copper Cliff Mine”."

Jan 1, 2015

By Osvaldo A. Bascur, Curt Heftier

The lack of integrated information including the Energy/Utility Suppliers with sufficient detail for analysis causes inefficient operation in metallurgical complexes including the Energy/Utility Suppliers . Defining the right context for information use is essential for sustainable operations. This being said, what are we doing to enable people to act upon information and to be aligned to optimize the use of resources like raw materials, energy, water and consumables for an entire metallurgical complex? Collaboration between all company entities is a key component of improving efficiency. Evolution of web technology and object modeling of enterprise assets enables collaboration across the whole business. Operational troubleshooting occurs more quickly as the organization acts on issues to reduce wasteful operation. This paper presents a real time software infrastructure with tools that give users the ability to sift through available data, transform data into information for business continuous improvement and optimization. We will introduce a new technology for analyzing real time data, information and events using multidimensional analysis of information to detect anomalies based on the statistics of the data classified by time events to reduce the information into action. A new paradigm for collaboration at a local and strategic level is proposed to enable the enterprise to become proactive in dealing with wasted time and products. Three examples from the industry will presented and their benefits highlighted.

Jan 1, 2011

By M. Zanini, D. Wong

ABSTRACT: Metals market improvements in 2005 drove the desire to increase nickel throughput and the production of nickel oxide sinter at the Vale Ltd. Copper Cliff smelter. Significant difficulties were encountered due to the unreliable quality of Bessemer matte being produced. Concentrate feed changes and the loss of technical and operational expertise during the previous market downturn contributed to the challenge of making the required improvements. Significant progress has been made in the converter aisle by focusing on employee engagement and standardizing best operating practices for a new generation of skimmers. This paper documents these initiatives and seeks to balance the art and science of converting.

Jan 1, 2012

By Ju-hyung Ha

New automated curing system for mass concrete has been developed to improve the quality of concrete structure and to save construction time and cost. The principle of this system is the automated water circulation system of heated curing water. Applied curing water on the surface of mass concrete keeps the temperature difference between center and surface of the structure below the threshold of specification. Mock-up test and field application have been conducted to investigate the performance of this system. In the results, new automated curing system reduced the chance of thermal crack occurrence and improved quality of the concrete structure as well.

Aug 1, 2013

By R. D. Westervelt

IN JULY 1954, the first iron ore from the deposits in the Knob Lake vicinity was mined and shipped to Seven Islands. The beginning of the production may well be the greatest advance in Canadian economy in the past fifty years. In 1955, the Canadian iron ore output was more than twice that of 1954, an in-crease due principally to the iron ore shipments from the Knob Lake area. Previous to this, Canada's iron production was 1.85 per cent of the world's output. Now, this percentage has risen to approximately 5.5 per cent and shows every indication of increasing further as the production rate from the area is increased. In 1955 the Iron Ore Company of Canada shipped over 7 million tons of iron ore and expects to ship over 10 million tons in 1956. Present facilities may be enlarged to handle up to 20 million tons per year. If the expected I 0 million tons per year are exported, Canada's iron exports will be second only to her wheat and newsprint exports. Before production began from the Knob Lake deposits, years of development were necessary in the area. Geologists spent several summers mapping the general area in order to unravel the complicated stratigraphy and petrology. Particular attention was paid to the mapping of the iron formation and all stages of alteration from fresh iron formation to ore were observed.

Jan 1, 1957

By M. Lahtinen

Traditionally, there have been three main methods for iron removal in the hydrometallurgical production of zinc. These methods are atmospheric precipitation of jarosite or goethite and pressurised precipitation of hematite. Jarosite precipitation is without doubt the leading and the most commonly used technology for iron removal. However, jarosite precipitation has some drawbacks, such as a low iron content (and, thus, high residue volume), high moisture content after filtration and often a high zinc content. These features make any environmentally acceptable way of using or disposing of jarosite more expensive, as compared to hematite and goethite. The importance of environmental regulations has grown in the zinc industry during the last decade, which will have an increasing effect on new investments. Hematite has several advantages over jarosite, such as a high iron content, low moisture and low zinc content. An important advantage of hematite is that it is suited for further use in the cement industry. However, until now the need for autoclave equipment has limited the spread and implementation of hematite precipitation in the zinc industry. Outokumpu Technology Oy has recently developed an alternative method for iron removal, which is the atmospheric precipitation of hematite. A patented method for precipitating hematite at atmospheric pressure is presented and compared with conventional methods for iron removal. The process conditions, the quality of the hematite precipitate and the environmental aspects are also discussed.

Jan 1, 2006

By Michel Mellinger

This paper presents preliminary results of a project aimed at obtaining a better understanding of the genesis of gold mineralization in northern Saskatchewan using lithogeochemistry. The properties sampled were: Weedy Lake (B Zone), Waddy Lake (Komis Zone) and Wedge Lake (Twin Zone) in the La Range belt, and the Rio mine in the Flin Flon area. Although the three vein-type deposits rudied here (Weedy Lake. Waddy Lake, Rio deposit) occur in different geological situation . a common gold deposition mechanism appears to have been active at all three location . Hydrothermal fluids carrying sulphur in solution in exces of gold thio-complexes moved through fractured host-rocks until they reached a site where pyrite precipitation wa triggered. As pyrite precipitated, the a/ aAu activity ratio of the fluid decreased. until a critical thre hold was reached and gold thio-complexe were de tabilized . resulting in the co-precipitation of gold and pyrite. The conditions triggering the precipitation of pyrite appear to have been: the abundance of iron in host-rock ~ilicates at Waddy Lake. and temperature decrease upon the reaching of structural trap~ at both Weedy Lake and the Rio deposit. with additional involvement of carbonatizationrelated reactions between fluid and host-rocks for the latter. In addition to pyrite precipitation , potassic alteration of the mafic metavolcanics is observed at Waddy Lake. while at the Rio deposit, the extensive carbonatization of the host-rocks i coupled with the deposition of chlorite that may have been remobilized from the altered mafic host rocks. In both the B Zone at Weedy Lake and the Komis Zone at Waddy Lake, a di tinct vanadium signature give some clue about the direction in which the hydrothermal fluids have moved . and the interpretation made is con istent with the geological ituation in either case. As for the Wedge Lake deposits, the distinct base metals-precious metals a sociation within a sulphide-facies iron formation confirm the volcanic exhalative origin of this gold mineralization .

Jan 1, 1986

By R. F. Robertson

"Adsorption isotherms of hexyl mercaptan vapour on synthetic sphalerite, zinc sulphide and zinc oxide were de-termined with a gravimetric McBain-Baker micro balance incorporated in the B.E.T. apparatus. Isotherms are given for hexyl mercaptan on synthetic sphalerite at 25°C, 0.5°C and 50°C; on zinc sulphide at 25°C and 1.5°C; and on zinc oxide at 25°C. All these isotherms are sigmoidal, with a definite change in slope at or close to the mono-layer. The amount of mercaptan adsorbed below the monolayer increases almost linearly with relative pressure to P/P0 = 0.8.Above this value, the amount adsorbed increases very rapidly with relative pressure. Hysteresis loops appear in the isotherms for all adsorption-desorption cycles. These loops are completely reversible. It is not possible to desorb the mercaptan monolayer from any of the adsorbents, even at elevated temperatures."

Jan 1, 1966

By I. Soosaiprakasam

This work investigated inhibition performance of copper carbonate (CuCO3), which is less toxic than conventional heavy-metal corrosion inhibitors in amine treating plants, The investigation was experimentally carried out in a bench-scale electrochemical corrosion cell under an atmospheric pressure, The inhibition performance of CuCO3 in an aqueous solution of monoethanolamine (MEA) was examined under a wide range of operating conditions and reported as a function of process parameters including inhibitor concentration, temperature and solution velocity, The results show that CuCO3 functions as an anodic inhibitor. The addition of CuCO3 decreases corrosion rate of carbon steel but might induce pitting corrosion/

Jan 1, 2005

By Paul T. Fitzgerald

Risk financing solutions are emerging to fully address environmental liabilities for mining operations. Supported by specialized insurance and alternative risk transfer (ART) products, mine owners can fund, cap and guarantee the environmental liabilities and closure obligations of a mine within a financial structure that will be acceptable to regulators. An environmental risk financing program will permit an owner to transfer the liabilities and indeed the ownership of a site to a third party that has the ability and resources to responsibly execute the closure plan. A properly structured program will be financially viable for the owner and will also respond to community and environmental opposition concerns about sustainable development and the environmental legacies associated with mining activities.

Apr 1, 2005