Search Documents

By D. Sediako

Excessive residual stress in Al engine blocks may result in cylinder distortion which reduces engine operating efficiency. As such, neutron diffraction was used to measure residual strain along the Fe liners and Al, in the hoop, radial and axial orientations with respect to the cylinder axis, at the cylinder interbore region. Residual stresses were subsequently calculated using generalized Hooke's law and related to the microstructure along the cylinder bridge. The results suggest that the residual stresses in the Al interbore region are tensile and increased with depth in the axial direction of the cylinder. The increase in residual stress at the bottom of the cylinder coincides with a finer and more uniform microstructure in this region of the cylinder. The refinement in microstructure at the bottom of the cylinder likely increased alloy strength, thereby decreasing this section's susceptibility to distortion. This study successfully quantified the residual stress profiles in a heat treated engine block and related the stress profiles to an as-cast engine block.

Jan 1, 2011

By J. C. Roy, S. Couture, C. Barbeau

The chemical composition of the asbestos tailings from different mines in the Eastern Townships of Quebec are fairly uniform in composition. The serpentine minerals antigorite and chrysotile form about 85 to 90 per cent of the total. Iron oxides add another 7 to 10 per cent; magnetite represents about 70 per cent of the oxides. Chromite is present in amounts of about 0.5 per cent. The average contents of elemental magnesium, iron and nickel are 23, 6 and 0.25 per cent respectively.

Jan 1, 1972

By A. G. Pentland

MODELS of mines may be classified under three headings: (a) sheet models, (b) solid models, and (c) skeleton models. Sheet Models are made of sheets of glass, celluloid, or a transparent plastic material. The sheets are mounted in a frame which holds them in a parallel position, either horizontally or vertically. Mine plans are traced on the horizontal sheets; sections on the vertical sheets. The model may be illuminated by electric lights which are separated from the sheets by an opalescent screen. It is viewed from above or from the side in such a way that the plans or sections are superimposed. Sheet models are very useful for the illustration of mines with narrow, steep-dipping veins, but they do not give a satisfactory representation of a large mine with a flat-dipping vein. Large sheets of glass are difficult to handle and to support in a frame.? It is difficult to see through a considerable number of them. Solid Models are made of plaster, concrete, wood, or other material usually in the form of slabs in which the mine workings are indicated by properly dimensioned cavities in the model. The slabs are coloured to show the veins, country rock, faults, etc. The model is divided along selected sections in order to give access to the interior by the temporary removal of parts. Solid models may be used to illustrate large orebodies of the Sullivan type, but they are cumbersome because parts must be removed to study details of structure. Skeleton Models are ones in which the underground cavities are represented by metal, wood, plaster, or wax proportionately shaped and held in place by a frame. They illustrate the work which has been done but do not show the position of the veins, dykes, faults, etc., in the unworked parts. It is necessary to project by eye between workings in order to determine the location of these features. The essential difference between the skeleton model and the solid model is that the skeleton model represents the mine workings by solid forms and does not show the unworked parts of the vein, whereas the solid model shows the vein as a solid and the mine workings as cavities in it. The skeleton model lends itself well to the representation of a large mine with large stopes.

Jan 1, 1944

By M. Walawalkar, C. K. Nichol, G. Azimi

Rare earth elements (REEs) are essential to the production of technologically advanced products, including wind turbines, electric and hybrid cars, automotive catalytic convertors, hand held electronic devices, and military defense systems. Their application in environmentally beneficial technologies puts them at a high priority for ameliorating environmental concerns. Because of their increasingly high demand and limiting resources, it is highly beneficial to find new sources for them. The present study is focused on leaching REEs from a phosphate based fertilizer by-product, known as phosphogypsum (PG). Global estimated world production of PG is about 240 million tonnes that is stored in the form of wet stacks adjacent to fertilizer production facilities, occupying vast amounts of land. PG also contains trace metals, which are detrimental to the environment, and hence it is crucial to monitor these stacks. We obtained our PG sample from Agrium Inc. (a fertilizer manufacturing company in Canada). We performed a comprehensive characterization of the PG sample and found that it predominantly contains Y, La, Ce, Nd, and Sm. For leaching purposes, we used hydrometallurgical acid leaching techniques. We investigated three acids over a range of operating conditions such as acid concentration, temperature, solid-to-liquid ratio, and residence time. We achieved an average leaching of 81% with hydrochloric acid as leachant using operating conditions that can be easily replicated in industrial settings. If our process is implemented, not only will it reduce the size of the existing PG stacks (mitigating their environmental risks), but also enable the development of new innovative routes for extracting REEs, making countries like Canada less vulnerable to supply disruptions.

Jan 1, 2016

By F. L. Casey

"Part 1 – Published Papers Baria, G., and Boshkov, S., ""Insights into Undercuttingin Block Caving"", Proc. 5th Rock Mech. Symp.,Mines Br. - Information Canada, 41-58, 1970.Barron, K., Coates, D. F., and Gyenge, M., ""ArtificialSupport of Rock Slopes'', Mines Branch ResearchReport R228, July, 1970.Barron, K., ""Criteria for Brittle Fracture Initiation inand Ultimate Failure of Rocks and Their Applicationto Fracture Zone Prediction"", Proc. 2ndCongr. Int. Soc. Rock Mech., Belgrade, 1970, 3-37.Bauer, A., and Calder, P. N., ""Projectile Penetration inRock"", Proc. 5th Rocle Mech. Symp., Mines Br. -Information Canada, 157-170, 1970.Bauer, A. M., ""Site Development and Rehabilitation ofPits and Quarries"", Canadian Mining Journal,Vol. 91, No. 7, 77, July, 1970."

Jan 1, 1971

By E. Ettles

This paper features some of the spectacular new advances in the fields of fluorescent penetrant inspection and magnetic particle concentration. Casting fractures in the various stages -before the repair, during the repair and in the completed repair -using the cold process method will be discussed. This cold method of repair eliminates problems of pre-heating and cooling and the stress factors that are involved in any heat repair.

Jan 1, 1971

By Ross I. Kelly

Carbonate rocks are widespread throughout Ontario and provide raw material for more uses than perhaps any other rock type. The principal carbonate rocks that are used by industry in Ontario are Paleozoic era limestone and dolostone. Limestone is a sedimentary rock that is composed mainly of the mineral calcite (CaCO,) while dolostone, also a sedimentary rock, is composed mostly of dolomite [CaMg (CO,),l. The majority of the province's limestone and dolostone extraction occurs from Paleozoic era rocks located in southern Ontario. Calcite and dolomite are also found in Precambrian marbles, calcite veins and carbonatites, however, utilization of these rocks by industry has been less common. Calcite and dolomite-rich rocks are utilized for a wide variety of uses including raw materials for cement and lime manufacture, chemical and metallurgical stone, fillers and construction aggregates (Derry, Michener, Booth and Wahl and OGS 1989a). For some uses chemical and physical requirements are very important. In the manufacture of glass, for instance, the chemical requirements of source materials are very important and very stringent. In other uses physical criteria such as whiteness may be more important. Although carbonate rocks are quite plentiful within the province, deposits that contain high concentrations of calcite or dolomite are somewhat limited. For that reason, this paper focuses on deposits that are known to, or may contain, a high percentage of calcite and/or dolomite. The paper emphasizes potential sedimentary limestone and dolostone resources, as these are the carbonate rocks most commonly utilized by industry in Ontario.

Jan 1, 2001

By Patrick E. Cavanagh

"A pilot shaft furnace was operated for one year at Steep Rock to produce special high-grade products from coarse ore, using lignite as fuel. The furnace is 10 ft in diameter and 60 ft high. When operated to heat coarse Steep Rock ore to drive off combined water and give a 64-per-cent-Fe product, the fuel consomption was 900,000 Btu's per long ton of product. The furnace was run in this way from September 1966 to January 1967 to establish the technique of feeding and discharging the furnace and controlling the gas composition and temperature. The furnace is similar in operation to a lignite water gas producer containing a large proportion of catalytic iron oxide. Steam injection is used to control the temperature. The product was tumbled in a rotary trommel to stabilize it. The resulting fines could be fed to the conventional pellet plant at Steep Rock. The furnace was next operated to make 77-per-cent-Fe metallized coarse ore. Several major modifications in de-sign were made and the furnace was successfully operated for short periods to maintain the required conditions to remove 75 per cent of the oxygen from the ore to give a 75-per-cent-reduced product at a grade of 77 per cent iron. The furnace cooling zone was operated under positive pressure, with internai alkaline water sprays to cool the charge. The product was discharged from the open bottom of the furnace without serions reoxidation. The metallized ore was magnetically separated from the discharge. Most of the charred lignite discharged along with the ore is re-cycled. Fuel requirement was 11,000,000 Btu's per long ton of product. This metallized coarse ore is intended for blast furnace feed. A short test run was carried out to establish the conditions for making a highly reduced melting stock for steel furnaces. To achieve 90 per cent reduction and over 90 per cent Fe, the furnace must be slowed down so that the production rate is about one-half the rate when making a 75-per-cent-reduced metallized product. Fuel requirement is 15,000,000 Btu's per long ton of product. The simple shaft furnace developed is similar to the top half of a blast furnace, with some major modifications to allow discharging into the open air. This Low Temperature Blast Furnace program has been technically successful and has resulted in making data available for the design of a commercial plant. Study of the commercial feasibility of large-scale production of metallized coarse ore at Steep Rock is still continuing."

Jan 1, 1968

By M. H. Cullender

THE determination of the flow characteristics of gas wells depends upon the analysis of pressure data obtained under shut-in conditions and under one or more known flow conditions. These data are commonly referred to as back-pres-sure test data, and I know you are all familiar with the back-pressure equation where, Q rate of flow, Mcfd @ standard conditions C coefficient of the back-pres-sure curve P 1 formation pressure, psia P • sand face flowing pressure, psia P2 (psia)2/1000 n exponent of the back-pres-sure curve Figure 1 is a graphical presentation of the back-pressure equation; the coefficient is the rate of flow at a difference in squared pressures of 1, in this case 2250 Mcfd, and the exponent defines the manner in which the rate of flow changes with a change in the difference in squared pressures. In Figure 1, the exponent of the back-pressure curve is 0.554 which means that for a 10-fold change in the difference in squared pressures, there will be a 3.58-fold (10 raised to the 0.554 power) change in the rate of flow.

Jan 1, 1961

By E. Dalgaard

During linear friction welding of titanium alloy Ti-5A1-5V-5Mo-3Cr (Ti-5553), the weld zone exhibits beta (B) grain refinement and alpha (a) phase depletion that have the combined effect of deteriorating the mechanical performance of the weldment. In this work, linear friction welded Ti-5553 was subjected to pre- and post- weld heat treatments in order to determine the conditions under which a phase depletion could be mitigated in the weld zone and thermomechanically affected zone (TMAZ). The mechanical response of the welded samples to the heat treatments was determined by performing tensile testing at room temperature. While the pre-weld heat treatments had no significant effect, the post-weld heat treatments were instrumental in restoring the strength of the starting (heat-treated) material.

Jan 1, 2011

By J. Kouam

Al-Si-Cu and Al-Si-Mg alloys are widely used in several applications. Although they can be produced near-net-shapes, products made of these alloys very often require some machining. The purpose of this study is to evaluate the machinability of A319 and A356 under TO and T6 conditions. The machinability was assessed using during dry drilling machining process and the machinability indexes used are the chip form, the chip breakability and the cutting forces. It is found that 319 and 356 exhibit different machinability behaviors, especially in the T6-condition in terms of forces requirements, chip breakability and chip segmentation. It is also found that both the microstructure of the workpiece materials and the machining conditions significantly affect the chip formation mechanism, and therefore, the machining parameters could be selected to promote a chip form that is easily manageable in production.

Jan 1, 2011

By Mihaita Matei

An adaptive approach to control the deformation in tube hydroforming process is presented. This requires: the use of an existing non-linear FE software (ABAQUS) that incorporates a user material model (VUMAT), the development and implementation of an adaptive control strategy to coordinate the internal pressure and the axial load so as to prevent fracture and wrinkling failures (knowledge-base controller) and the application of the developed adaptive simulation approach for finding the optimal loading path required to hydroform a defect-free part with as uniform thickness distribution as possible (user's load subroutine (VDLOAD). In order to validate the approach, the case of conical hydroforming and the case of bending followed by hydroforming component is discussed.

Jan 1, 2011

By E. Swartzman

"IntroductionGENERALLY, the necessity for mining coals of higher impurity content, the drive for lower costs by intensive mine mechanization, changing market requirements, and the increasing competition of oil and natural gas, have continued to result in an upward rise in coal preparation, and have necessitated a more intensive study of coal preparation problems.Increasing adoption of •continuous mining equipment, for example, is introducing new problems in coal preparation. Limited experimental work in the United States (1) shows that the effect of the continuous miner on size distribution varies with the characteristics of the seam. In some seams, the fines problem is lessened, in others it is greatly aggravated. Generally there is a decrease in the relative amount of the top sizes (plus 2 in.) and a substantial increase in the intermediate sizes (down to about 1/8 in.). Contrary to expected results•, where continuous miners with vertical-moving cutting heads are used, an increase in impurities in the slack sizes does not necessarily occur where draw-slate is taken. This is because the draw-slate tends to be kicked out in lump form. However, if a seam contains bands •and lenses of impurities they are bound to be in the mined product."

Jan 1, 1952

By F. Khomamizadeh

In this study, deep cryogenic treatment was applied to A319 cast aluminum samples. Although the cryogenic treatment didn't have any significant effect on mechanical properties of the well degassed and fluxed samples, but the tensile strength of the samples containing a considerable amount of gas and shrinkage defects was improved surprisingly, This improvement was attributed to the strengthening of the a-aluminum matrix which slows down the propagation of the existing defects. There was no significant increase in the hardness after cryogenic treatment, The abrasion resistance of the alloy was improved after cryogenic treatment, by developing a homogeneous protector shield, composed of abrasive grains penetrated into the soft aluminum matrix and kept tight.

Jan 1, 2005

By M. A. Marois

This paper proposes an improved temporal stability condition for the implementation of an inverse heat transfer method for predicting the time-varying bank thickness of the phase change protective bank inside a high temperature furnace. The direct problem is handled with the enthalpy method. The inverse method rests on the Adjoint Problem and the Conjugate Gradient Method. It is shown that the temporal stability condition for the inverse phase change problem relies on the time delay of the temperature measurements. Results indicate that this time delay is proportional to the heat diffusion time including heat diffusion through the mushy zone.

Jan 1, 2011

By Karl J. C. Harries

"9.1. INTRODUCTIONIn Chapter 5 of Volume I royalties are dealt with and several topics would appear to be duplicated in this Volume. However, Volume I may be looked upon as a general guide, whereas this Volume is a reference volume. It deals in considerable detail with specific provisions and concepts relating to royalties between private parties. This does not, however, mean that Chapter 5 can be ignored. It should be looked upon as a source of general information concerning royalties between private parties and as a negotiating aid intended to give an overview of various topics. You may well find that in its general approach it will lead you to ask a question which, hopefully, will be dealt with in this Volume .It should be remembered that royalty agreements are agreements with a particular focus, and so the concepts set forth in Chapter 1 apply to them. This chapter addresses a few considerations specific to royalties that will usually form part of an agreement rather than a stand-alone agreement.9.2. FORMAT FOR ROYALTY PROVISIONSIn many of the cases where royalties arise, they are adjunct to, or part of, other arrangements. For example, a royalty may form part or all of the consideration to be given to an owner upon purchase of his property, or it may arise if a joint venturer ceases to contribute to the venture and has his interest converted to a royalty.1 It is with such situations that this section primarily deals; if the royalty is contained in an agreement that is singularly, or primarily, concerned with creating it, then it is just a normal agreement.Commonly, by the time the right to receive the royalty arises, at least some of the other provisions of the agreement have been performed and/or become redundant. For example, in an option agreement the royalty will be a continuing obligation of the optionee, usually arising only after the option has been exercised.2 In a joint venture agreement, a royalty will often arise where the interest of a non-participating venturer has been diluted and converted to a royalty, in which case the recipient will usually become a passive party, entitled only to his royalty, and most of the rights that he enjoyed as an active venturer will cease to be effective."

Jan 1, 2003

By Z. Tang

A collaborative project was performed between NRC Institute for Fuel Cell Innovation and MagPower Systems Inc, to develop a cost effective fabrication process to manufacture the anode for magnesium-air fuel cell with improved performance. A novel fabrication process was developed, which resulted in a porous microstructure with increased surface area, instead of the traditional solid structure. This porous anode greatly increased power density in the magnesium-air power source. This fabrication process is very simple and cost effective. Especially, this process makes it convenient to incorporate different alloying additions, as well as hydrogen inhibitor and electrolyte management additive into the anode. The anode composition was designed so that micro galvanic cells were formed as current is drawn out of the fuel cell, and resulting increased dissolution rate of Mg. It is feasible to incorporate hydrogen inhibitor and electrolyte management additive into the porous anode, and the anode with some kinds of inhibitors exhibited improved electrochemical performance. This paper describes the microstructure and electrochemical performance of anodes with designated porous structure and alloying additions. Furthermore, quantitative kinetics analysis of the obtained I-V curves and electrochemical impedance spectroscopy were carried out to clarify the mechanism.

Jan 1, 2005

By Gordon Smith

ABSTRACT Gold-bearing quartz veins in the northeastern Ontario and north western Quebec mining camps are shown to have been mineralized in part by epithermal solutions. The vertical gradient of pressure during this stage of mineralization is calculated, using decrepitation temperatures of quartz and thermoelectric potentials of pyrite. The base of the Cobalt sediments, which lie uncomformably over part of the mining region, may be taken as datum level in calculating the depth of erosion into the basement below that level. The vertical extent of the epithermal gold mineralizaiton in this region is at least 9,000 feet below the datum level. INTRODUCTION IT WOULD have been difficult a few years ago to convince economic geologists that after making a series of measurements in a laboratory in Toronto, the depth of erosion which has taken place below the base of the Cobalt sediments at any place in the Ontario-Quebec mining region can be calculated to the neare.st 500 feet, or that the same series of measurements would also serve to allow a prediction of the minimum vertical depth of probable ore in a producing mine in the same region, with the same degree of certainty. Possibly it is just as difficult today, but the following description of the data and calculations may help to demonstrate the reliability of the method.

Jan 1, 1951

By Patrick R. Stephenson

The Australasian Code for Reporting of Mineral Resources and Ore Reserves (the ?JORC Code?) has been operating successfully for 14 years, and has an ancestry dating back over 30 years. Together with complementary developments in stock exchange listing rules, the Code has brought about substantially improved standards of public reporting by Australasian mining and exploration companies. The Code is regarded as a world leader in its field, and has been used as a basis for the development of resource/reserve reporting standards in other countries. The reasons for its success are varied, foremost amongst them being its adoption in full by the Australian and New Zealand Stock Exchanges, and the ability and willingness of mining industry organisations to bring Competent Persons to account when necessary. The latest revision of the JORC Code was undertaken in 2002/03, based in part on releases of upgraded reporting standards in Canada, United Kingdom/Western Europe and South Africa, and the 2003 edition is expected to be released mid-year. Two of the more significant changes are: the introduction of a requirement for a Competent Person to be responsible for the documentation upon which Exploration Results are reported; and inclusion in the definition of a Competent Person of a reference to ?Recognised Overseas Professional Organisations?, being overseas professional organisations to which Competent Persons may belong for the purpose of preparing documentation for the submission of reports to the Australian Stock Exchange.

May 1, 2003

By G. Kallfa P. Geo

Exploration at both Greenfields and Brownfields stages entails business risks of different nature and success rates. Greenfields exploration is exceedingly assumptive and the success rate of exploration or return on investment is low because exploration is an inherently risky business. Brownfields exploration on the other hand is less risky, as the geology is better understood, but generally speaking since the larger ore bodies close to surface have already been found the return is lower. In addition, most exploration at the Brownfields stage is generally more expensive due to extensive use of drilling. Surface geology mapping and expensive drilling have been key technical contributors to most exploration programs over the last two decades. However, as client expectations, logistics, target depths and complexity of exploration programs increase, there has been a growing emphasis on using geophysical techniques to complement other methods. Integration and optimization of various geoscientific disciplines is becoming more important in successful exploration programs of the future to reduce exploration risks, successful integrated exploration requires putting reliable geophysical parameters and correspondent petrophysical property contrasts into an assumed or conceptual geological model. This paper discusses a new multi-parameter geophysical methodology finalized in a unique conceptual geologic model which can be used either as a root model in grassroots exploration or as an efficient tool in Brownfields exploration to successfully find satellite orebodies of almost any size. The application of a new multi-parametric geophysical approach to Brownfields exploration is illustrated with examples from Manitoba, including a past producing nickel sulphide deposit in Lynn Lake and the Reed Copper deposit, currently in development.

May 1, 2013