Search Documents

By H. A. Steane

THIS BRIEF PAPER presents the information available on the use of Dorrclon?is in the middling re-grind unit at the lead-zinc mill of Canadian Exploration Limited. The plant throughput is 1,650 tons per twenty-four hours. The flotation feed is ground to 60 per ?Cent passing through 200 mesh. It contains some composite 11articles of sphalerite in calcite, and these reported either in the final zinc concentrate, thus lowering the grade, or in the tailing, with loss of zinc. The re-grind unit was set up in the zinc flotation circuit to liberate the sphalerite from these middling particles, to raise the grade of concentrate and improve recovery. Grinding through 325 mesh should give substantial liberation of locked sphalerite. The middling regrind unit consists of two Dorrdones and one ballmill arranged as shown in the -accompanying flow-sheet. The Hardinge ball-mill, size 7 ft. x 36 in., was free for this use as a result of recent plant expansion. The two Dorrclones were purchased, and the necessary pumps and pipe lines were installed to complete the regrind unit. The unit has been developed over a period of two years by several steps and various flow schemes until reaching tl1e present flow scheme. These steps are not elaborated here, because the changes were made to determine the best product to work on for flotation metallurgy, and not because of the Domrolone classifying ability.

Jan 1, 1956

By P. E. Cavanagh

FOR THE PAST seven years Mr. W. Simpson, Chief Mechanical Inspector for the Nova Scotia Department of Mines, has carried out exhaustive field trials of non-destructive inspection equipment in the coal mines of that Province. This work has demonstrated the usefulness of a number of types of non-destructive inspection when used for periodic inspection of hoisting and haulage equipment in the coal mines of Nova Scotia. As a result, the Dominion Coal Company has instituted a programme of regular preventive maintenance inspection ?by a special staff of qualified and trained men. The purpose of this present paper is to describe how non-destructive testing techniques are used on ropes, axles, couplings, and other hoisting and haulage equipment, how these methods are being used in other industries, and the expected benefits from intelligent and properly organized use of these techniques in the coal mining industry.

Jan 1, 1956

By R. K. Mishra, A. Kula, X. Jia, M. Niewczas

The mechanical properties of Mg-Gd and Mg-Y solid solutions have been studied under uniaxial tension and compression between 4K and 298K. The results reveal that Mg-Gd alloys exhibit higher strength and ductility under tension and compression attributed to the more effective solid solution strengthening effect and grain boundary strengthening. Profuse twinning has been observed under compression, resulting in a material texture with strong dominance of basal component parallel to compression axis. Under tension, twining is less active and the texture evolution is affected mostly by slip. The alloys exhibit pronounced yield stress asymmetry and significantly different work-hardening behaviour under tension and compression. Increasing of Gd and/or Y concentration leads to the reduction of the tension-compression asymmetry due to the weakening of the recrystallization texture and more balanced twinning and slip activity during plastic deformation. The results suggest that under compression of Mg-Y alloys slip is more active than twinning in comparison to Mg-Gd alloys.

Jan 1, 2015

"Load-haul-dump machines (LHDs) are typically used in underground metal mining operations. Delays or inappropriate use of LHDs can result in production loss. Optimized LHD use is especially crucial in larger mines because longer travel distances increase heat, dust, and gas emissions, which in turn increase ventilation costs. This study, conducted at an existing Swedish sublevel cave underground mine, used discrete event simulation and the AutoMod™ DES tool to determine the ventilation costs related to using too many diesel LHDs in a production area with reduced ore pass availability. When fewer ore passes are available, ventilation costs related to operating LHDs in the production area were found to increase by as much as 200, 224, and 306% for one, three, and six LHDs in operation, respectively. ¦ KEYWORDS Discrete event simulation (DES), Loading operations, Production rate, Ventilation costs RÉSUMÉ Dans les exploitations souterraines d’extraction des métaux, on utilise généralement des chargeurs-transporteurs (LHD, de l’anglais Load-haul-dump machines). Les retards ou l’utilisation abusive des LHD peuvent entraîner une perte de production. L’utilisation optimisée des LHD est particulièrement importante dans les grandes mines en raison des longues distances parcourues, lesquelles augmentent la chaleur, la poussière et les émissions de gaz qui, à leur tour, décuplent les coûts de l’aérage. Cette étude, menée en Suède dans une mine souterraine utilisant la méthode d’exploitation en sous étages avec foudroyage, s’est basée sur la simulation à événements discrets (SED) et l’outil de SED AutoMod™ pour déterminer les coûts de l’aérage liés à l’utilisation d’un nombre trop élevé de LHD alimentés au diesel dans la zone de production, avec une disponibilité réduite de la cheminée à minerai. Lorsque les mines disposent de moins de cheminées à minerai, l’étude montre que les coûts de l’aérage liés à l’exploitation des LHD dans la zone de production augmentent respectivement de 200, 224 et 306 % pour un, trois et six LHD en fonctionnement. ¦ MOTS CLÉS coûts de l’aérage, opérations de chargement, simulation à événements discrets (SED), taux de productionINTRODUCTION Transporting material from the mine face to the dumping location requires flexible loading and hauling equipment that is able to cope with sharp curves and a complex mining environment. Load-haul-dump machines (LHDs) are designed for such an environment. Models are available to suit specific features of the working environment such as small, large, or narrow open stopes (Atlas Copco Rock Drills AB, 2007). When carrying a full load, haulage speed is higher for LHDs than for front-end loaders with the same engine size. Also, payloads are approximately 50% higher for LHDs than for front-end loaders (Atlas Copco Rock Drills AB, 2007). LHDs are capable of climbing steep (Bloss, Harvey, Grant, & Routley, 2011). The haulage distance between stope and ore pass is usually between 50 m and 400 m. LHDs are efficient for tramming distances up to 200 m (Bloss et al., 2011), whereas when loading trucks, the LHDs work efficiently when the distance is less than 100 m (Atlas Copco Rock Drills AB, 2007). The largest diesel-powered LHDs, with drive motors of up to 350 kW, can handle a payload of 21 t (Wennmohs, 2014). Most mining equipment runs on diesel fuel, which provides flexibility, high durability, and high efficiency (Pronk, Coble, & Stewart, 2009); however, other alternatives such as electric, hybrid diesel/electric, or hydrogen fuel cell machines are increasingly being developed and used. This change is due to diesel-powered machines accounting for a significant portion of the ventilation costs in the mine (Chadwick, 2008; Paraszczak, Laflamme, & Fytas, 2013). Currently, as part of the European sustainable intelligent mining systems (SIMS) project, Epiroc AB is planning to demonstrate technology for a diesel-free underground mine at Agnico Eagle’s Kittlä mine in Finland using"

Jan 1, 2019

By R W. Drybrough

The program to increase production at Sherritt Gordon's Lynn Lake property, which began in 1956, included increasing the rope speed and the horsepower of the ore hoist at the "A" shaft. Because of the limited power sup-ply from the two 7,000-hp. hydroelectric plants, and the ? 3,600 hp. predicted for the combined hoisting requirements of the three production shafts, it was considered desirable to lessen the impact of this type of load on the relatively small power system by equipping all future hoisting arrangements with Ward Leonard direct-current drives. The manually operated 8-by 4-ft. hoist at the "A" shaft had a rope speed of 1000 f.p.m., and was driven by a 385-hp., 380-r.p.m. wound rotor motor with liquid rheostat control. This A.C. drive was replaced by a semi-automatic Ward Leonard direct-current drive with a 515-hp., 566-r.p.m., shunt wound motor, providing a rope speed of 1,500 f.p.m. During several months preceding the con-version, all possible preparations were carried out to keep the changeover period to a minimum, and this resulted in a total shutdown time of twelve days. The capability of the "A" Shaft hoist was increased from 109 tons per hour to 134 tons per hour, and both mechanical and electrical maintenance were reduced considerably. The total cost of the conversion amounted to $130,000. The hoistmen who had been required for the manual A.C. drive were transferred to the new Farley shaft, and the reduction in operating labour costs of the "A" Shaft hoist

Jan 1, 1965

By A. Montera, M. Loken

"The process of blending consistent and predictable feed for the roasters is critical for optimizing product quality and controlling production costs. To assist in this process, online PGNAA slurry analyzers have been installed and evaluated at a Sudbury Ontario smelter. They are used to measure 100 % of the full process stream to obtain elemental composition data in real time. This paper explains the application details at Sudbury and the benefits achieved from their full stream, elemental slurry analyzers.INTRODUCTIONSudbury Integrated Nickel Operations (Sudbury INO), a Glencore Company, consists of two underground nickel/copper mines in Sudbury, Nickel Rim South and, Fraser, along with the Strathcona mill and the Sudbury smelter. The facilities are spread throughout the 60 kilometer-long, oval-shaped geological formation known as the Sudbury Basin (Figure 1). The company has been mining nickel-copper ores in the Sudbury area since 1929. Nickel and copper are the primary focus of operations at Nickel Rim South and Fraser. Other base metals such as cobalt and precious metals are also produced.The Strathcona Mill receives ore from Nickel Rim South, Fraser, and third-party miners to produce two concentrate streams. One is a nickel-copper concentrate for use by the Sudbury Smelter; the other is a copper concentrate which goes to other Glencore operations for smelting and refining. The Sudbury Smelter converts the mineral concentrate into a high grade matte containing nickel, copper, cobalt and platinum group metals. This matte product is shipped to Glencore's Nikkelverk refinery in Norway for further processing. In 2015, the Sudbury INO Smelter completed the first phase of the Process Gas Project (PGP); a series of process changes and capital investments designed to reduce sulphur dioxide (SO2) emissions in accordance with Ontario Regulation 194. A critical element of the planned emissions reduction was the elimination of a higher percentage of sulphur contained in input concentrate streams, which can then be captured and converted to sulphuric acid."

Jan 1, 2017

By S. Jain

Construction industry is considered as labour intensive, having shortage of skilled labour, unsafe with large number of industrial accidents. Construction industry requires high technology automation products (Robots) for improving productivity, safety, quality etc. Robots are developed by various countries in different areas like demolition, earthwork, bridge, tunnels, road work, underwater works, trenches and piping, maintenance etc. however they are still not used to their full potential by construction industry. Hence in this paper, the authors propose a ?model for adoption? of robots in construction industry. This model considers how a construction firm will adopt full scale robots like manually controlled machine, tele-controlled machines, computer controlled machines and cognitive robots and assimilate them through various stages.

Aug 1, 2013

By H. Thalenhorst

For an advanced mineral exploration project that has a ?nugget? issue making the assessment of the deposit grade difficult, a bulk sampling program using a sample tower can provide information that is otherwise not obtainable prior to actual production. This information includes the verification of predicted resource grades for the bulk sample tonnage (and, indirectly, of the methods and parameters used for the grade estimate), confirmation of the physical and grade continuity of the mineralization, and geotechnical data for a future mining operation. The information gathered will improve the input of a feasibility study, particularly with respect to expected mining grades, which are the key economic parameter for most mining projects. The bulk sample rejects can be used for pilotscale metallurgical testwork. Bulk sampling is also useful in cases of potentially biased drill-hole assay results and in the reliable determination of ore grade before shipment of ore from production or development operations to an external beneficiation plant. This paper presents a practical bulk sampling and sample preparation protocol, lists design features for the sample tower, examines the sampling errors that will be encountered, provides information on quality control procedures, and looks at the costs and benefits of such a program, based on the experience of undertaking bulk sampling programs during the period of 1985 to 2008.

May 1, 2010

By F. J. Hrach, K. P. Flynn, P. J. Miranda

"ST Equipment & Technology, LLC (STET) has developed a processing system based on tribo-electrostatic belt separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. In contrast to other electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the triboelectric belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) particles with very high throughput. The high efficiency multi-stage separation through internal charging/recharging and recycle results in far superior separations that can be achieved with a conventional single-stage free-fall tribo-electrostatic separator. The triboelectric belt separator technology has been used to separate a wide range of materials including mixtures of glassy aluminosilicates/carbon, calcite/quartz, talc/magnesite, and barite/quartz. Separation results are presented for selected industrial mineral sources. An economic comparison of using the tribo-electrostatic belt separation versus conventional flotation for barite / quartz separation illustrates the advantages of dry processing for minerals.INTRODUCTIONThe lack of access to fresh water is becoming a major factor affecting the feasibility of mining projects around the world. According to Hubert Fleming, former global director for Hatch Water, “Of all the mining projects in the world that have either been stopped or slowed down over the past year, it has been, in almost 100% of the cases, a result of water, either directly or indirectly” (Blin et al., 2013). Dry mineral processing methods offer a solution to this looming problem."

Jan 1, 2016

By M. Kataoka, Y. Obara

It is known that compressive strength and tensile strength of rocks vary significantly with specimen size. Rocks are composed of crystals and grains in a fabric that includes flaws such as microcracks, grain boundaries and pores. As the likelihood of including severer flaws becomes greater for a larger specimen, the strengths are small. On the other hand, the size effect in the fracture toughness of rocks has not been made clear until now because there are few studies focused on it. In this paper, Semi- Circular Bend (SCB) test was performed using Kimachi sandstone with various specimen sizes. A shape of the specimen is a semi-circular disc with an artificial notch. The specimens were prepared with various thickness t and radius r as the following two groups; t was changed from 10 to 37.5 mm with r = 37.5 mm in the specimen of group (a), and r was changed from 12.5 to 150 mm with t/r = 0.8 in the specimen of group (b). As a result, there was no significant change in the fracture toughness with different t. On the other hand, the fracture toughness increased with increasing r and converged on a certain constant value in a range larger than approximately 70 mm of r. Consequently it was clear that the size effect in the fracture toughness of the sandstone exists.

Jan 1, 2015

By R. D. Brown

Manitoba has now joined Ontario and Quebec in providing for new incentives and lower tax rates for the mining industry. A single rate of tax (to replace the former two-tier royalty), an investment tax credit and a relatively straightforward set of rules for calculating taxable mining profits are the main features of new mining tax legislation announced by Manitoba&apos;s Finance Minister Donald W. Craik in his May 15, 1979 budget address. On introducing amendments to reform The Metallic Minerals Royalty Act, the Finance Minister indicated that the new tax regime is intended to restore the Manitoba mining tax system to a competitive position in Canada, and should result in renewed investment in the province&apos;s mining industry. 1n this regard, the government could be right-there is little question that the new tax regime will produce greater incentives for the mining industry than the two-tier royalty system introduced by the New Democratic government in 1975. The proposed changes, contained in Bill 57, would largely be effective January I. 1979.

Jan 1, 1979

By B. M. Das, F. Claridge, V. K. Garga

Coal, as well as a large part of other minerals in Canada, is produced by surface mining methods. This has resulted in short and long-term accumulation of waste rock in dumps. Two main problems arise from the flow of water through these dumps: stability of dumps and the impact on stream flows. In recent years, a number of mines have started placing waste rock in valleys for general disposal or far constructing mine access road ways. All these have created challenges in the following areas: effective design of dumps and flow-through dams; stability monitoring of the structures; environmental impacts downstream by way of increased amount of fines in suspension, sedimentation, and toxic substances; and long-term status of flow and flood. Similar situations also exist in many civil engineering structures. This paper discusses the status of rock drains and the immediate and future research needs.

Jan 1, 1990

By MKS Vel, S. Mukhopadhyay, R. Mishra

Off late, the criteria of selecting the refractory have acquired a trend line aiming to a cleaner environment and the utmost importance is given to the eco-friendly approach. The stainless steel making furnaces normally use mag-chrome refractories for the obvious reasons of changing slag basicity from acidic to basic. Such refractories generate toxic fumes and compounds with hexavalent chrome, which is unhygienic if inhaled. The present paper describes the development of a chrome free alumina magnesia carbon refractory, it&apos;s different test properties, simulative testing and microstructures. The optimum quantity and distribution of carbon in the brick restricts the carbon pick-up by the steel. Bricks with the same composition were manufactured in the commercial scale and used in a stainless steel making furnaces in USA. The performance of same refractory in this furnace was quite encouraging and at present the same quality brick has become a normal practice in this furnace. Since no chromite is used in making this brick, so no toxic compounds are generated environment remains pollution free.

Jan 1, 2004

By W. Holdsworth

The flotation mill of Dentonia Mines, Limited, at Greenwood, B.C., went into operation on April 20th, 1934, and by October 11th a total of 15,000 tons of ore had been treated. It is intended in this paper to describe briefly the operation and to give some of the operating data which have been gathered. The metallic minerals in the Dentonia ore are pyrite, chalcopyrite, galena, and, occasionally, native gold, and the gangue includes chloritic material, vein quartz, and calcite. Pyrite makes up about 90 per cent of the metallic content of the ore, in which it is disseminated as irregular grains and well-formed cubes. An average analysis of the ore is: gold, 0.27 oz. per ton; silver, 1.73 oz. per ton; copper, 0.12 per cent; lead, 0.31 per cent; and zinc, trace. From the mine ore-bin, situated near the portal of the tunnel at the mine, the ore is hauled by motor truck to the mill, a distance of three-quarters of a mile, and there dumped into the receiving bin, which has a capacity of fifty tons. The hauling is done during one eight-hour shift, commencing at 7 a.m. The maximum size of the ore fed to the mill-bin is ten inches. Lumps larger than this are broken by sledge hammer to pass through grizzly bars, spaced ten inches apart, installed above the bin. The ore is drawn from the bin by a 30-inch, 6-ply conveyor belt, 18 feet 6 inches long. In the near future, when the cross-cut tunnel is completed, the ore will be trammed to the receiving bin. This will effect a considerable saving in cost. At the same time, the bin will be set back several feet, so that the length of the conveyor belt may be doubled. This will make efficient ore-sorting possible, and so ensure a minimum of waste rock in the mill feed.

Jan 1, 1935

By F. Vagnon, A. M. Ferrero, M. Pirulli, A. Segalini

"The topic of this study is the design of flexible fences to mitigate the risk due to debris flow phenomena by means of theoretical and experimental studies analysed in framework of the Rock Engineering System (RES).The study of the interaction between debris flows and flexible barriers is a major challenge since many different aspects concerning both the slope characteristics and the structure features are involved. Debris flows are often triggered by the mobilization of debris deposits that are generated by rock fall of adjacent rock walls. The rock debris deposits are difficult to be characterized by the physical and mechanical point of view due to their large variability in volume distribution and, moreover, when dealing with high mountains environment, they are also strongly affected by the presence of water at different phases (solid or liquid) depending on the temperature. The debris deposit turns unstable in relation with the geotechnical and environmental features of the areas and the instability evolution in high mountain steep valley is often a debris flow. Debris flow destructive potential is very high and protections are often needed to reduce the debris flow risk.This complexity determines the needs of comprehensive study able to include the global basin dynamic and the environmental conditions. An a-priori analysis of the influence of the different aspects can be useful to focus on the real driving aspects of the problem. Due to the complexity of the system the application of the RES methodology is recommended in order to clearly define the different assumptions needed, their influence on the simulations and a comparison among them.RES allows investigating triggering criteria, flow and depositional processes and interaction of flows with protection fences in a rational way. For this purpose, an interaction matrix is created: it summarizes the key geotechnical parameters that influence debris flows, their interactions and debris/engineering protection opera behaviour. The goal is to quantify the diagonal-off terms to assess the residual risk after barrier construction, using back analysis from real debris flow event and data collection from literature.This methodology is applied to analyze a debris flow event in the Italian Western Alps where numerical analyses are carried on to assess flow characteristics to be used for fence design through the application of an analytical and numerical model developed by the authors (Brighenti et al, 2013). In particular, the velocity and deposition heights have been estimated using the numerical code RASH3D (Pirulli, 2010), which is a single-phase model based on depth-averaged Saint Venant equations. Pathways of different lengths are studied to assess the input data necessary to design the protection barrier and to determine the associated risk. Simulation of the barrier at different places along the valley will also allow to determine optimal barrier location in terms of minimum residual risks by comparing the velocity, the volume and the energy of the debris after the barrier impact.The work will produce a possible design scheme to be adopted in this environment."

Jan 1, 2015

By P. C. McLeod

THE GECO OREBODY, located north of lake Superior in the Thunder Bay district of northern&apos; Ontario, was discovered in 1953. Diamond drilling in the following year indicated a 15,000,000-ton ore-body, and production plans were made for the shipment of copper and zinc concentrates in three years. To accomplish this, the Geco Project was initiated. The property was in an undevdoped, inaccessible area, and the project involved the conversion and extension of a logging road to the property, the construction of two railways and seventy miles of hydro transmission line, the erection of a municipality, the building of a plant, and the development of an underground mine to produce 3,300 tons per day. This paper describes some of the methods used in the underground development phase of the Geco Project.

Jan 1, 1958

By R. Pressacco

"IntroductionAgrium’s history in fertilizer production and marketing goes back to 1931. Today, Agrium Inc. is a world leader in the production, distribution, and marketing of fertilizers and related products to the agricultural industry. Agrium is the largest North American producer of nitrogen fertilizers, a major producer of phosphate and potash fertilizers, and a world leader in fertilizer wholesale distribution and retail marketing. The mine at Kapuskasing is located some 40 km southwest of Kapuskasing, Ontario (Fig. 1). It has been developed to supply high-quality, low-cost phosphate rock to the company’s Redwater, Alberta facility, where it is an ingredient in ammonium phosphate fertilizer production. The Kapuskasing mine is the only phosphate mine in Canada and will rank as one of the highest-grade phosphate mines in the world (Clark and Duncan, 1999). Apatite is the principal ore mineral mined at the Kapuskasing Phosphate Operations.GeologyThe first record of exploration in the area was from a program executed by Continental Copper Mines in 1955 which evaluated the magnetic anomaly located in the Cargill and Cumming townships for its base metal potential. Intermittent exploration of the base metal potential of this magnetic anomaly continued in the following years, until the phosphate potential of the area was first examined in 1974 by International Minerals Corporation which recognized the presence of a layer of apatite sands overlying the carbonatite host rocks.The local geology consists of a core complex of multi-phased carbonatite rocks which are surrounded by a ring of pyroxenite, and have provided a U-Pb age date of 1907 Ma ± 4 (Sage, 1988). These two rock types are in turn situated within quartz diorite gneisses that form a large portion of the Kapuskasing Structural Zone (Fig. 2). The carbonatite host rock is sub-divided into two sub-types: sovite and rauhaugite. The sovite is a medium- to coarse-grained, white, banded rock in which calcite is the dominant carbonate species and it includes accessory minerals such as phlogopite, magnetite, clinohumite, apatite, olivine, pyrrhotite, and amphibole. Apatite can reach 15% abundance in this rock type (Sage, 1988). In sharp contrast to the sovite, the rauhaugite appears as a massive, fine-grained, dense, beige to tan-coloured rock in which dolomite is the dominant carbonate species. Phosphate values can range to 14% P2O5 in the rauhaugite."

Jan 1, 2001

By M. Phylli Bray

"Mining has the reputation of being a very ""macho"" industry. Recently, wider educational opportunities for women in nontraditional occupations and changes in mine technology have combined to make mining a viable career choice for women also. To benefit from this new resource, the mining industry faces the challenge of developing a different work environment from the one now burdened with sexism. Management supported initiatives are needed to facilitate such a transformation. The same rethinking of gender attitudes might also be extended to mining women in their traditional role as ""wife of"". The assumption that the male worker&apos;s wife is an unpaid adjunct is being questioned. It is suggested that women&apos;s separate concerns both as helpmate and as part of the mining workforce should be considered when planning for mining into the 21st century.IntroductionI must confess that, during the preparation of this paper, there have been many moments when I questioned my temerity. After all, I am not male, I am not an engineer, and I have never had a position in mine management. But as the wife of a mining engineer and a long-time resident of Northern Ontario mining towns, I do have an interest in the mining industry. This interest has had little to do with the technical and management aspects of the industry. Instead my research has been concerned with the impact the mining industry has on the people involved, particularly women, whether directly as employees or indirectly as wives. As I look toward the 21st century, I believe that the whole question of gender relations in the mining industry is one of the critical management issues smouldering below the surface."

Jan 1, 1995

RÉSUMÉ L’estimation la plus précise possible des coûts de minage est d’extrême importance pour les études de préfaisabilité afin de diminuer les risques financiers des projets miniers. Les méthodologies existantes d’évaluation des coûts de minage ne permettent pas de les évaluer avec des marges d’erreur acceptables tout au long de l’évolution des projets miniers. Elles visent à évaluer les coûts unitaires de minage des études préliminaires de faisabilité, pour les principales méthodes d’exploitation, en prenant pour l’hypothèse que ces coûts dépendent principalement du taux d’extraction journalière. Si cette hypothèse peut être justifiée pour l’évaluation du coût d’opération, elle est fort discutable pour l’évaluation des coûts de minage. Pour démontrer que cette hypothèse est inadéquate nous avons analysé la méthode d’exploitation la plus populaire sur le continent nord-américain c’est à dire celle par chambres vides avec retrait horizontal (Hr – Horizontal retreat), ou « Longhole » et celle avec retrait vertical (VCr - Vertical Crater retreat). Il ressort de cette analyse que les coûts unitaires de minage dépendent principalement des conditions géotechniques du massif rocheux et de la largeur du gisement et non pas du taux d’extraction journalière du minerai.

Jan 1, 2010

"The content of production reports has its origins in raw measurements taken in harsh production environments. The ensuing measurement/estimation errors always affect reproducibility such that, regardless of the fact that they are balanced through statistical data reconciliation, reported numbers are simply the most probable values of inferred probability distributions. This has important implications for how metal recoveries should be monitored and reported. Indeed, in a context where many process optimisation activities are based on small improvements in recovery, there should be no doubt that inadequate handling of measurement/estimation errors can easily exaggerate or mask actual changes in process performance. However, estimates of the reproducibility of reported metal recoveries are rarely reported to plant management. This situation persists despite the fact that a code compliant metal accounting system must inform management about business risks related to metal accounting. To this extent, this paper focuses on the continuous management of reproducibility level of metal recoveries in compliance with the best practices. Sensitivity analysis of primary and secondary metal accounting models is performed to show the resulting probability distributions for metal recoveries. Some guidelines are given for designing and managing metal accounting systems capable of achieving and sustaining predefined levels for the reproducibility of metal recoveries.INTRODUCTIONEach and every mineral processing plant produces daily, weekly and monthly production reports in which metal balances for payable and penalty elements are presented. While such production reports are usually consulted in offices, underlying raw measurements are taken in harsh production environments where mechanical vibrations, humidity, corrosion and dust, to name a few, disturb measurement procedures. It is thus no surprise that several authors (Francois-Bongarcon & Gy, 2002; Gaylard, Randolph, & Wortley, 2014; Holmes, 2010; Spangenberg & Minnitt, 2014) have reported pervasive issues related to mass/sampling measurements in the context of mineral processing."

Jan 1, 2016