Search Documents

By Adrian E. Scheidegger

"AbstractThe possibilities of deriving pertinent information about fractures in an oil pay from data obtained by core analysis are investigated. It is shown that it is possible to obtain an estimate of the fractured area per unit volume of the pay, and that the size of the fractures can be estimated if their shape is known. A suggestion of a routine procedure for the analysis of fractures is given.1.-IntroductionMany oil fields are producing essentially from cracks or fractures. Where this is the case, it is important to be able to obtain a knowledge of the size and distribution of those fractures in the oil pay. This knowledge has to be derived from the analysis of cores taken from the fields, as it is generally impossible to follow a fracture through the pay by direct means. The necessity of using statistical methods to extrapolate the meagre information obtained from the cores of the wells is therefore indicated.It is known that the fractures are much bigger than the diameter of the cores; thus, if they strike a core, the latter will generally fall into two pieces. The angle of the fracture with the vertical can be measured and, if oriented cores are taken, the exact position of the surface element representing the intersection of the fracture with the drill stem can be determined. Sometimes the edge of a fracture can be seen in a core. The number of •Cores that show such an edge can be noted. Of course, one has to be careful to distinguish between original fractures in the pay and fractures in the core caused by drilling operations. Only the former are relevant."

Jan 1, 1955

By J. Dilbeck, J. K. Ratliff, T. Petrov, Z. Brown

"In efforts to improve dust control during deep cut continuous mining a supplemental atomizing spray system, mounted on 14CM15 continuous miner, has been designed and successfully implemented in a U.S. coal mine. The mine is 2.1 m (7-ft) high and uses a blowing curtain face ventilation system with 1.1 m (3.5-ft) curtain offset from the rib. The face ventilation design parameters were set to 9.4 m3/s (20,000-cfm); 4.2 m3/s (9,000-cfm) line curtain flow rate, and 3.8 m3/s (8,000-cfm) scrubber capacity. The performed in-mine measurements, before and after the implementation of the atomizing spray system, showed a significant decrease in the respirable dust levels at the operator place as well as at the return. The paper describes the supplemental water spray system design and performance supported by three-dimensional computational fluid dynamics (CFD) simulations and in-mine test data.INTRODUCTIONThe work on this project have started in 2015 with a study of the conventionally applied face ventilation layouts. The specific behaviour of the face ventilation system have been analyzed trough in-mine measurements and computer modeling of typical cut scenarios. An computer modeling methodology have been developed for estimation the respirable dust concentration (RDC) using tracer gas to RDC contour mapping, calibrated by a single point value, provided by in-mine measurement. Utilizing the results of this study the engineering staff of the mine designed and implemented a supplemental atomizing spray system to improve the dust control during the deep cut continuous mining. Today the atomized spray system is successfully applied demonstrating steady performance and a significant decrease in respirable dust concentration on the working places of the continuous miner (CM) and coal transporters (CT) operators as well as at the return air stream. Information about the applied type of spray nozzles provided by other researchers (Cheng, 1973; Dick et al., 1996; Organiscak & Page, 1998; Pollock & Organiscak, 2007) and spray system manufacturers (Spraying System Co, 2011–2018; Steinen Mfg., 2016) have been used in this project. CFD code and simulation approach validated in a study conducted in 2000-2014 have been applied (Turner et al., 2002; Wala et al., 2004, 2007; Petrov, 2014)."

Jan 1, 2019

By K. R. Barnard, K. D. Marte, T. V. Gamarano

"The first commercial scale application of CSIRO’s direct solvent extraction (DSX) technology has been in operation at the Boleo project in Mexico since December, 2015. In this application, DSX is a synergistic solvent extraction system consisting of the extractants LIX 63 and Versatic 10 for recovery of cobalt and zinc from a solution background of manganese, magnesium, and calcium. Key operating parameters such as metal extraction, phase disengagement and extractant stability are summarized and discussed in this paper.INTRODUCTION Commissioning of the Boleo processing plant, located on Mexico’s Baja peninsula, began with the copper circuit starting in late 2014, with first copper cathode production achieved in January, 2015. The cobalt and zinc circuits began commissioning in December, 2015 with first zinc sulphate monohydrate (ZSM) and cobalt cathode production achieved in February and April, 2016 respectively. The Boleo project flow sheet and development has been described in detail in previous publications (Dreisinger, et al. 2005; Dreisinger, Baxter, & Molnar, 2006; Dreisinger, et al. 2008; Dreisinger, et al. 2009) and is summarized schematically in Figure 1. Boleo is a mixed oxide/sulphide Cu-Co-Zn-Mn high clay deposit that is processed in a whole ore, atmospheric, oxidative and reductive, sulphuric acid/seawater leach. Copper is recovered as cathode by conventional solvent extraction and electrowinning. Cobalt and zinc are recovered, from a solution background of manganese, magnesium, and calcium, by CSIRO’s synergistic solvent extraction technology Direct Solvent Extraction (DSX). Cobalt and zinc are bulk stripped from the DSX circuit and then further purified by phosphinic acid solvent extraction to produce zinc sulphate monohydrate granules via spray dried granulation and cobalt cathode rounds via divided cell electrowinning."

Jan 1, 2017

By A. West, F. Mohammadi

Growing awareness of selenium bioaccumulation has resulted in selenium management becoming an important environmental issue for mining operations. Selen-IX™ is a novel ion exchange based technology developed by BioteQ to provide an effective solution for removing selenium oxyanions from mine impacted water to single-digit µg/L levels. The technology offers significant potential benefits when compared to incumbent biological treatment processes, including substantially reduced capital and operating costs and significantly reduced production of a selenium-containing sludge for final disposal. This paper reviews the key features of the Selen-IX™ process and presents the results of recent pilot testing on selenium impacted water.

Jan 1, 2014

By J. E. Udd, L. B. Geller

"Mine-shaft wire-rope discard regulations include, among other criteria, a limited amount of permissible loss-of-breaking-strength (LBS). Currently, this parameter is estimated on the basis of non-destrutive-testing (NDT) with electro-magnetic (EM) type instruments. This paper analyses the accuracy with which these estimates have, so far, been obtained in practice.It concludes that while certain types of testers have produced better results than others, the desired accuracy level has not been attained. Also discussed are the putative reasons for this situation, and appropriate actions that the mining industry might wish to take."

Jan 1, 1990

By James E. Wennen

The through-put and energy efficiency of an autogenous (AG) grinding mill are adversely affected by variability in rock size and rock competency. This applies to both fully autogenous and semi-autogenous (SAG) grinding circuits. In this paper we focus on an approach to overcome the problem of inconsistent mill through-put related to variability in mill feed size and rock competency. The focus is on ores containing hard, competent rock. This approach consists of preparing feed to an autogenous mill that contains 20% coarse media rock and 80% of material crushed to pass 37 mm. Results of pilot-scale testing for two iron-ores will be presented to show that a 10% to 12% reduction in unit energy consumption is possible with prepared feed, compared with feeding the mill with conventional primary crusher discharge.

Jan 1, 2012

By C. Karpuz, Y. S. Istanbulluoglu

This paper describes the results of convergence measurements conducted about five years for the re-use gate roadways at OAL lignite mine in Turkey. Double lignite seams separated with a marn layer, are mined with long-wall retreating mining system at the mine. Rib pillar has been abandoned and gate roadways were planned to be packed for the re-use of full extraction. Various packing systems have been attempted, namely three rows of woodenchock, one row of wooden chock plus concrete wall and concrete wall only. The re-use of maingate roadways packed with wooden chock yielded 62% of closure. Lastly developed concrete packing of 3 meters wide and specially developed support set composed of three friction props and a cap, which is a modification of yieldable set, have successfully maintained the main and tail gate roadways stability with a total vertical convergence of 32%. Good correlation has been established between pack stiffness and floor heave as well as maingate and tailgate convergences. The elimination of rib pillars by re-use of gate roadways increased the coal recovery by 20% and decreased the development/production ratio from 0.065 m3/ton to0.022 m3/ton.

Jan 1, 1997

By E. L. Chanturiya

The research and characterisation for compositional, physicochemical, structural, electrical and flotation properties of various pyrite samples for a copper-zinc sulfide ore was carried out. Various methods were used during the research, such as optical microscopy, X-ray diffraction, electron probe micro-analysis (EPMA), phase emission analysis, routine chemical analysis, auger electron spectroscopy (AES), scanning electron microscopy (SEM), back-scattered electron images (BSE), potentiometry, and instrumental neutron-activation analysis, flotation. Analysis of obtained results established the interrelation between impurity structures and concentration of electric charge carriers in minerals, Butyl xanthate sorption and flotation yield of pyrite. The research concluded that pyrite samples differ by morphology, micro defects of structure, concentration of donor and acceptor impurities (Co, As, Sb, etc.) and conductivity parameters (thermo-electrical force, specific resistance and concentration of charge carriers The peculiarity of pentagon-dodecahedral pyrite is the high concentration of electric charge carriers (electrons) and the more negative surface potential (by 25–75 mV) in comparison to cubic pyrite. The surface of cubic varieties is more active, therefore it is oxidized in alkaline lime medium much faster, than the surface of pentagon-dodecahedral varieties. This phenomenon is caused by high reaction ability, irregular jointing and defects of cubic pyrite. This promotes the increase of calcium ion sorption on its surface and the decrease of Butyl xanthate sorption. According to this, an increase in alkalinity (lime medium) from a pH of 10.0–11.5 leads to an increase of gold content reporting to the tail of bulk flotation. Gold content is increased from 0.58 g/t (?? 9.5) to 1.9 g/t (?? 11.6), which represents an increase in gold recovery of 24.68 to 79%, respectively.

Jan 1, 2016

By J. S. Fox

It is generally recognized that the interpretation of bedrock geochemical data in volcanic terrains can be improved by adjusting for rock-type. Various chemical attributes of volcanic rocks have been put forward in the literature as rapid indicators of rock-type, but there is some question as to which of these is the most reliable . Only one such attribute, total iron, seems to have seen systematic use in geochemical mapping in the Flin Flon region. Discriminant analysis of 500 basalts, andesites, dacites and rhyolites suggests that SiO2 is the most important rock-discriminating variable and that MgO, CaO, TiD2, AI2O3 and FeOtot, are successively poorer discriminators. Lithological normalization in the subalkaline volcanic environment should therefore be made over ranges of this variable. Trace-metal data from drill core through the sulphide orebody at Hanson Lake, Saskatchewan are used to demonstrate various approaches to lithological correction, including silica normalization, factor analysis and trend analysis. All of these extract economically important information from the core that is not apparent in the raw data logs. However, silica normalization does not seem to be subject to as many serious limitations as factor and trend analysis in this case, and therefore seems to provide the most reliable basis for the interpretation of subsurface exploration geochemical data.

Jan 1, 1978

By J. B. Hamilton

The advantages of generating and distributing electrical energy direct from the coal-fields so closely affects the mining industry that a few remarks on the unbalanced phases of coal distribution is worthy of attention. The value of coal imported into Canada from 1912 to 1921 exceeded the sum of $580,000,000. In 1922 Ontario imported 1,640,000 tons of anthracite and 9,440,000 tons of bituminous coal. I submit that the use of Saskatchewan lignite in an electrical super-power plant equipped for the carbonizing of coal, and disposal of excess gases would be the commencement of a solution of the fuel shortage in Ontario. As Saskatchewan becomes more and more populated and manufacturing increases, the amount of by-product carbonized fuel available for shipment to Ontario will increase, and its shipment to that province would decrease the trade deficit of the national balance sheet. If and when this is carried out it will mean a better and wider market for Alberta fuels in Saskatchewan and Manitoba.

Jan 1, 1924

By Keith Jones, Largo Albert

"Decelerometer testing of a rigid guide system in a mine shaft pro vides usefuI information to operating and maintenance people. High acceleration/deceleration rates can lead to high maintenance costs to bath conveyances and shaft and can also present an operating risk . Possible disastrous results in the shaft have been avoided by restricting the maximum conveyance speed until the shaft and/ or conveyance problems have been solved.The test instrument is a valuable aid especially during commissioning or updating of a hoisting installation. High acceleration/deceleration rates also lead to reduced hoist rope life. During the past fourteen years, a total of 15,000,000 feet of testing was performed in 74 assorted shaft compartments.Based on this experience, it is possible to establish acceptable conveyance maximum speeds provided that all other conditions in the shaft compartment are normal. The body of the paper will present examples of several tests made under actual operating conditions.IntroductionMore and more mine operators are recognizing the real value in the use of the decelerometer for determining the state of shaft guide alignment in their shaft compartments , not only during the initial mine start-up periods, but also on a regular basis while the mine is in production.Decelerometer testing, is a technique in which an accelerometer , commonly known as a decelerometer, is used for measuring conveyance acceleration/deceleration in a lateral plane. lts purpose is to determine the severity of shock loads produced by misaligned shaft guides. Testing is performed by mounting the instrument on the conveyance and operating the conveyance (empty and loaded) at various speeds up to and including full speed . However, full speed may not be attained due to conditions indicated by the tests. These conditions may present an operating risk to the plant."

Jan 1, 1984

By P Hulteberg

In this article, an integrated catalytic reactor design approach to produce PEMFC-quality hydrogen is evaluated. The design is based on a high level of heat exchanging perfonned internally, highly active noble metal catalysts and a woven wire mesh catalyst support system. It consists of an integrated steam refonner and a catalytic burner section, a water gas shift section and a preferential carbon monoxide oxidation section. The reactor design is described and experiments perfonned to evaluate the two reactors built are reported. The two reactors have a maximum output of 3 Nm and 10 Nm3 hydrogen/h respectively. In the larger unit, a total of six fuels, three gaseous (methane, natural gas and liquid propane gas) and three liquid (naphtha, ethanol and methanol), were evaluated. The larger unit was also used to investigate how variations of parameters such as steam-to-carbon ratio in the steam reforming part of the system and the relation between oxygen and carbon monoxide in the preferential carbon monoxide oxidation affect the reactor perfonnance. The smaller unit was used, after implementing automatic control, to run a system life time test for 480 h. The refonner system perfonned according to specifications on almost every aspect.

Jan 1, 2005

By J. E. Hawley

"IntroductionA STUDY of the trace elements in the ash •of coals from nine seams in the Sydney coalfield, Nova Scotia, was undertaken at the suggestion of Dr. W. A. Bell, Geological Survey of Canada, as a part of a larger study of these and other Nova Scotia coals being made by the Geological Survey and the Nova Scotia Department of Mines under the direction of Dr. P. A. Hacquebard.The main purpose of this investigation has been to •determine if a knowledge of the trace element distribution might be of assistance in the recognition of individual seams, the distinction of which is not always easy or positive in folded and faulted strata by ordinary stratigraphic and structural means.The study has been so conducted as to afford information on the variation of trace elements in individual petrographic intervals or divisions in each of the seams examined, intervals determined by Dr. Hacquebard on the basis of their banded ingredients, vitrain, clarain, durain, fusain, etc, as observed under the microscope in polished sections. The results, as well, indicate the trace element composition of the coals of the area as a whole, and quantitative data for fifteen elements are given, along with concentrations of thirteen other elements, stated in terms of intensity ratios. Data on distribution of germanium, though considered here along with other elements, are dealt with elsewhere*."

Jan 1, 1955

By L. S. Almeida, U. A. Courbassier, C. T. Guimãaraes, M. N. Souza, V. L. Silva, H. P. Dias, G. A. Bicalho, B. S. Rocha, P. N. Rodrigues, A. Carnevale

During primary aluminum production the anode changing is a very important task. So improvements on it will be essential to avoid disturbance and have a better operational control. After anode changing a good current distribution will be guaranteed using a cavity cleaner and precise anode setting. Albras switching a manually anode setting to an automatic one solved the setting problems. In this paper it will be shown some pot line results and the improvements on workers ergonomic and safety conditions. The device was developed in a partnership between Albras and Pesto.

Jan 1, 2006

By G. Rong, W. Du

Stability of some potential unstable blocks in the left bank slope of Baihetan hydropower station is evaluated in this paper using the three-dimensional (3D) limit equilibrium method. The Baihetan hydropower station is in the downstream of Jinshajiang River, China. The geological condition in the river valley is complex, and many large discontinuities are detected in the slope of the two banks. As a result, much attention should be paid to the stability of the slope in the feasibility study stage. Because the left bank slope is an oblique consequent one, we mainly focus on the slope stability analysis in the left bank. Comprehensive geological exploration is conducted in the studied area and the detected discontinuities are well researched. By building a 3D geological model of the left bank slope, three potential unstable blocks which are close to the dam site are detected. An irregular wedge analysis method is then used to calculate safety factors of the three blocks under three conditions, which are natural condition, rainfall condition, and seismic condition, respectively. It is found that the safety factors of the block 1# and the block 2# are quite low when compared to the suggested values. Extra care must be exercised when excavating the slope near the block 1# and the block 2#. A preliminary reinforcement is also suggested.

Jan 1, 2015

By M. D. Everell

Le Centre de Recherches minérales (CRM), qui est un organisme de recherche appliquée du ministère de l'Energie et des Ressources du Québec, a été créé en 1969, dans le but de procurer un support scientifique et technique à l'industrie dans le domaine des mines et de la métallurgie. Pour atteindre ses objectifs, le CRM met à la disposition de l'industrie un personnel spécialisé et compétent dont une quarantaine d'ingénieurs et de scientifiques. Etant donné la nature même de l'industrie minérale, ce personnel est très versé dans l'étude des problèmes diversifiés des domaines de la technologie minière, du traitement des minerais, de la métallurgie extractive et de l'analyse minérale. Ce Centre de recherches met également à la disposition de l'industrie une usine-pilote permettant de reproduire les résultats du laboratoire au moyen d'un appareillage de type industriel, d'obtenir des échantillons en quantité suffisante pour une exploration du marché et de familiariser du personnel avec les opérations normales de l'industrie. Certaines de ses contributions récentes au développement de l'industrie minérale du Québec seront présentées.

Jan 1, 1985

By Pizhi Zhao, Yingdong Li, Hailong Cao, Yingjuan Feng

"Three types of anodic films (unsealed, hot water sealed and agent sealed) were prepared to study the effects of anodizing pores structure on the adhesive bonding performance of AA5754 automotive sheets. The morphology of the anodic films was examined by using scanning electron microscope (SEM) and the composition was examined by glow discharge optical emission spectroscopy (GDOES). The adhesive bonding strength and durability in corrosive environment were investigated by using single lap shear test and salt spray corrosion test (SST), respectively. The results showed that the pores structure could significantly influence the adhesive bonding performance. The unsealed sample showed porous structure and provided high bonding strength, however, the durability was poor in corrosive environment. The hot water sealed sample showed fine and loose hydrated alumin a structure on the surface and provided high durability in corrosive environment, but the bonding strength was low. In contrast, the agent sealed sample provided both high bonding strength and durability in corrosive environment.INTRODUCTIONAdhesively bonded aluminum joints by using adhesives have been widely used for the realization of lightweight design in industrial applications like automotive and aerospace industry[1, 2]. Durable bonds which are capable of taking structural loads can be created due to a careful consideration of the way in which the joint is formed, the type of adhesive and the appropriate treatment of the adherend surfaces prior to bonding[3-6]. Experiences demonstrate that the surface treatment is the most critical step which could not be disregarded, since it is essential to achieve long-term service capability [7].In structural applications, a bonded assembly is expected to maintain a significant load and may be combined with exposure to harsh environmental conditions in its service life. For this purpose, the pretreatment for structural bonding of aluminum alloy must provide not only strong tensile strength and durability but also good corrosion resistance. Chromic acid anodizing (CAA) process provides an anodized layer which has good corrosion resistance while also exhibiting useful adhesion characteristics as well as lacquer coating retaining characteristics[8].However, the use of Cr (VI) is unadvised from a health and environmental point of view since it is toxic and carcinogenic, and this process is gradually limited even prohibited. Boeing's phosphoric acid anodizing(PAA) process provides a more open pore structure allowing penetration of high molecular primers/adhesives[8]and PAA process is the most widely used pre-surface treatment suitable for adhesive bonding between aluminum alloy components. Rahimi et al. demonstrated that nanostructure can be produced by PAA process and is affected by the time of pretreatment and anodizing parameters [9]. Xu et al.investigated the influence of surface energy and roughness on adhesive bonding through PAAprocess and provided improved adhesion performance under certain anodizing parameter[10]. However, PAA process is normally not recommended for a major concern of deterioration of the mechanical performance of the joints as a result of exposure to a wet and corrosive environment. Sulfuric acid anodizing(SAA)process, recently, has been widely used for corrosion protection and good base coating for the adhesion of lacquers in aerospace manufacturing[11]. The good performance is explained by properties such as the porous morphology and high adsorptive power of the oxide film, the chemical and electrical inertness of the anodized layer. Moreover, modified sulfuric acid could also used for adhesive bonding. Lunder et al. found that anodizing in hot sulfuric acid is promising as a simple, very rapid and environmentally friendly pre-treatment for adhesive bonding[12].Saeedikhani et al. studied the process of phosphoric/boric/sulfuric acids anodizing and found it was is a promising pre-treatment for adhesive bon"

Jan 1, 2018

By C. E. Lancelle, J. T. Volk, H. F. Wang, D. Fratta

"The Main Injector Neutrino Oscillation Search (MINOS) Near Detector Hall at Fermilab and the Lafarge – Conco Mine are located approximately 100 meters underground in the Galena-Platteville dolomite just below its contact with the overlying Maquoketa shale in Northeastern Illinois, USA. A new cavern was excavated adjacent to the MINOS Near Detector Hall at Fermilab to house the near detector for the Off-axis Neutrino Appearance Experiment (NOvA) program. During this excavation approximately 1150 cubic meters of shale rock were removed. Tiltmeter arrays consisting of a series of hydrostatic leveling sensors (HLS), which are spaced regularly over a total distance of 50-to-100 meters, were used to monitor subsurface deformations. The tiltmeter response in the MINOS Near Detector Hall due to the NOvA cavern excavation is approximately thirteen times the estimated response based on using laboratorydetermined properties. The discrepancy between modeled and measured tilt is likely due to differences in Young’s Modulus in the rock mass versus in a small laboratory sample. Amplitudes of measured solid earth tides differ from the amplitudes of theoretical solid earth tides by up to 40 percent for both arrays. This is likely due to a local heterogeneity or discontinuity.INTRODUCTIONLong baseline tiltmeters have been used to record small earth movements since the early 1900s. One of the first studies using long baseline tiltmeters to measure earth tides was published by Michelson (1914). He used a leveled 152-meter long, 0.15-meter diameter tube half-filled with water connecting two concrete-lined pits. The pipe was trenched 1.75 meters underground in Williams Bay, Wisconsin in a sandy-clay soil. Initially only an east-west line was used, though a north-south line was added after it was seen that viable results were obtained. Measurements were made by hand either hourly or once every two hours depending on the time of day. When compared to 0.7 times the calculated earth tides, the tiltmeter signal matched almost exactly. This excellent result began the use of long baseline tiltmeters to measure small earth movements."

Jan 1, 2015

By A. Galip Ulsoy, K. V. S. Sastry

"This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology. and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control. IntroductionEconomically accessible higher-grade ores are being rapidly depleted, and at the same time the demand for mineral raw materials continues to increase. Mineral recovery from the remaining low-grade or finely dispersed ores requires grinding for liberation. High energy consumption during grinding and poor efficiency associated with the beneficiation of fine minerals are two important problems facing the mineral industry . These problems, coupled with advances over the last 10 to 15 years in the areas of process modeling, instrumentation, computer technology and control theory, have made automatic control of mineral processing systems an important research area(23,52,66,67,120,129,152)."

Jan 1, 1981

By Jaeheon Lee, Junmo Ahn, Doyun Shin

"Many alternative leaching systems including bacterial leaching have been introduced to avoid passivation on the surface of chalcopyrite and to increase the leaching efficiency of copper from chalcopyrite. Recently, glycine, one of the simplest amino acids, has been emerging as an efficient and environmental-friendly lixiviant to recover copper. In the present study, an alkaline glycine–peroxide lixiviant system was used to leach copper from chalcopyrite concentrate and the leaching mechanisms were also investigated by a suite of kinetic studies under different conditions. The chalcopyrite concentrate contains 28.8% copper with 30.8% sulfide sulfur. The effect of concentration of glycine and hydrogen peroxide of the leaching solution was investigated. Glycine concentration was varied from 0.5 to 1.0 M and the hydrogen peroxide concentration was changed between 3 to 5%. Leaching time and pulp density were also varied. Hydrogen peroxide is an oxidant of the system and the leaching efficiency with periodic additions of the peroxide was also studied. A mineralogical study was performed using XRD and SEM. To investigate the surface of the residue materials, XPS was used to see if any passivating layer was formed during the leaching. Detailed results from mineralogical, chemical, and metallurgical studies will be presented and discussed.INTRODUCTION The greatest global resource of copper is low-grade chalcopyrite and heap bioleaching may be the only economic option for its processing. However, formation of a passivating layer on the surface of chalcopyrite slows down the oxidation reaction and reduces the efficiency of the process."

Jan 1, 2017