Search Documents

By Dale A. Walters

The thermal recovery of bitumen reservoirs by steam assisted gravity drainage (SAGD) is often designed to maximize the operating pressure. In general, the benefits of higher operating pressures are higher steam temperatures that maximize the reduction of oil viscosity, potential permeability enhancement associated with lower effective stress and shear dilation, and a larger pressure window to allow flexible control of the producer. This is especially important for shallow reservoirs where the pressure window for injection and production is smaller. Higher operating pressure can reduce thermal efficiency (due to heat losses), but the other benefits usually compensate. The limitation of the maximum operating pressure is then based on maintaining caprock integrity. Thus, shear and tensile failure mechanisms must be quantified and managed. This paper presents a geomechanical analysis of caprock integrity for SAGD operation. Both analytical and numerical approaches are used to investigate the modes of caprock failure. Main factors in the analysis are the knowledge of the initial stress state and proper representation of the complexity of the geomaterials. Typical initial stress states for northern Alberta are presented showing the potential for low initial minimum total stress and elevated initial shear stress levels. The stress-strain behavior for the sand and caprock materials is discussed focusing on the potential for shear dilation in the sand and shear strength behavior in the caprock. Elasto-plastic constitutive models used to represent the sand and caprock are presented and compared using numerical analysis. The increase in pressure and temperature alter the stress state and disturb the soil matrix. This disturbance results in shear dilation of the sand matrix creating regions of enhanced permeability and porosity. Also, the transfer of stress and strain to the caprock causes dynamic stress changes and, therefore, dynamic behavior of shear and tensile failure conditions. Calculations are presented showing the stress paths associated with SAGD operations, suggesting better design of lab testing programs and the implications for shear dilation in the sand and shear failure in the caprock.

Jun 1, 2012

By Robert Strachanm

The East Kootenay coal-field, situated close to the boundary between the provinces of Alberta and British Columbia, is composed of four small areas locally called the Crow's Nest Pass, the Upper Elk, the Flathead and Crown Mountain, and comprises an area of about 3 78 square miles. From eleven to twenty-five seams have been exposed of two feet and over in thickness, with a total thickness of about 200 feet of coal, and reckoning about one hundred feet to be workable, gives an estimate of coal available of about thirty-seven billion tons. The coal is a high-grade bituminous, occasionally tending towards anthracite, and the majority of the seams furnish a. very good quality of coking coal as well as an excellent steam coal. The coal-field is found in the mountain ranges in long narrow strips. The age of the fonnation and the thickness of the covering beds have had considerable influence on the character of the coal, and lateral pressure and disturbances in the process of mountain-building have wrought great changes. With such an abundance of coal, it has been a disappointment that the East Kootenay field has not figured larger industrially. So far only one portion of the coal-field has been utilized. This is the Crow's Nest, where, in 1898, the Crow's Nest Pass Coal Company commenced development. Access to the coal seams was easily obtained, the mountain creeks having eroded away the covering, and mines were driven into the coal seams. In that year about ten thousand tons of coal were produced from the mine at Coal Creek.

Jan 1, 1924

By Jehan Rondot, Raymond Marleau

"Des quartzites trés pars ont été découverts au cours de la cartographie de la region du lac des Martres, étape de l'étude géologique de la region de Charlevoix.On distingue quatre groupes métasédimentaires, tons con tenant des niveaux de quartzite dans an mains deux domaines géologique différents, c'est à l'ouest, clans le do¬maine gneisso-charnockitique que se situent les quartzites du groupe des Martres. Quartzite et gneiss à, grenat et sillimanite, en banes épais, constituent la formation de La Galette. A Pest, dans un environnement gneisso-granitique, les deux groupes métasédimentaires de Saint-Siméon, et de La Malbaie comprennent, par contraste, des bancs pen épais et de compositions variées. Les niveaux de quartzite dépassent rarement 50 m d'épaisseur. L'autre groupe métasédimentaires, celui de Saint-Tite des Caps, recoupé de nombreuses intrusions charnockitiques et granitiques, ne possède que de minces niveaux de quartzite.La pureté et la grande épaisseur des quartzites de La Galette suppose une histoire complexe qui se termine par des depots continentaux de climat aride, par opposition aux depots marins des autres groupes. D'autre part, la presence de ces quartzites an sein de roches Presque anhy¬dres et de haute temperature que sont les charnockites leur confére des caractéristiques de fusion sans decrepitation.Parmi la multitude de depots de quartzite qui existe clans le monde, peu sont de qualité supérieure. Or, de par sa composition chimique, le quartzite de La Galette se compare avantageusement à ceux des meilleurs gisements des Etats-Unis, de l'Europe de l'Ouest et de l'Afrique du Sud. D'accès facile pour l'exploitation, les gisements ne sont qu'à une trentaine de milles de Baie Saint-Paul ou de La Malbaie, sur le Saint-Laurent.L'utilisation en metallurgic prévue pour le quartzite de La Galette comprend la production de silicium, de ferro¬silicium et d'autres alliages de silicium. La composition du quartzite est en outre appropriée pour la production de carbure de silicium et de silicate de sodium. Les fines peuvent être utilisées pour la fabrication du verre et comme matiere de charge"

Jan 1, 1977

By W. H. Stheeman

"The high rock pressures at the deeper levels of the Tsumeb Mine have necessitated the changing of the mining methods and the introduction of cable bolts. After two rockfalls in the cable-bolted stopes, the mechanics of cable bolting were investigated. Practical methods were developed to find the best grout mixtures, the bond stresses between cables and cement, the bond stresses between rock and cement and the load on the cable bolts, which was mathematically calculated from data observed underground. The design of the cable bolt support system as used at the Tsumeb Mine is explained. GeneralThe Tsumeb Mine is in northern South West Africa/Namibia, approximately 400 km by road from the capital city, Windhoek, at an elevation of 1300 m above sea level. Mining operations in Tsumeb were started in 1905 by the Otavi Minen und Eisenbahn Gesellschaft and continued, with an interruption during the Depre ssion, until 1940, when the mine was closed and taken over by the Custodian of Enemy Property. The present owner, Tsumeb Corporation Limited, obtained the mine in 1947 and restarted the underground mining operations in 1949 after the mine was dewatered. Currently, the stoping operations are between 26 Level (840 m below surface) and 38 Level (1260 m below surface). In addition, the mine is an important silver producer and has produced 670,100 kg of silver since 1947."

Jan 1, 1982

By L Munholand, G. Soucy, P. Quintal

This work presents early results from the first study to optimize the hydrodynamics of a Plasma Lift Reactor (PLR). The PLR is designed to break down organic contaminants in aqueous solutions. New experimental results are presented for air/water tests and for plasma degradation of organic contaminants in Bayer liquor. In addition, a multiphase Computational Fluid Dynamics (CFD) model has been developed which predicts the hydrodynamic behavior in the PLR. These results of this work suggest the PLR is effective at reducing contaminants in the Bayer liquor and that the CFD model adequately describes the hydrodynamic flow.

Jan 1, 2005

By T. Imgrund, A. Bischoff, S. Spürk

"Specific conditions of underground coal mines at great depth, such as high temperatures, high rates of methane inflow and natural ventilation pressure provide considerable challenges for the reliable design of appropriate mine ventilation systems. For decades coal mining in Germany has coped with these extreme circumstances. Based on these experiences appropriate software tools for simulating mine ventilation networks have been developed and continuously enhanced. This paper examines differences in the simulation results and underlying calculation methods of two software solutions. The analysis is based on the comparison of FlowNetTM and VentSim DesignTM (Version 5.1) regarding the accurate prediction of fluid mechanical quantities and their validation with real measurements. A special focus lies on exceptional ventilation scenarios typical for deep coal mines, like gas inflows, fire events and buoyancy effects. The purpose of the comparison is the future utilization of the experiences gained during mining at up to 1,500 m depth for state of the art ventilation design. INTRODUCTION Ventilation is an essential component of mine operations—as providing fresh air to workplaces, diluting and removing explosive, toxic or asphyxiating pollutants and assuring sufficient climate conditions. On the other hand, the costs of ventilation contribute to a large extend to the overall operating costs of a mine, as the share in the energy consumption of a mine may be in the range of 25–50% (Belle, 2008). Accordingly, proper design of ventilation systems has been a task since early times. Consequently software for modelling of ventilation networks has been developed in order to improve efficiency and accuracy of calculations (Maleki, 2018). Compressible flow has not been considered by initial ventilation modelling software tools. In Germany, the consideration of changes in airflow density—depending on pressure and temperature—in the algorithms of ventilation simulation software has been started in 1974 by Duepre & Hofbauer. This development had been continued by the Pruefstelle fuer Grubenbewetterung (Test Centre for Mine Ventilation) and resulted in the release of a computer ventilation software named “Wetter”. The mine inspectorate of the German state of North Rhine-Westphalia, which supervises the major coal mining district in Germany, declared ventilation simulation based on compressible flow being “state of the art” in 1985 (Pollak, 1985). This pronouncement made allowance for assessing the consequences of underground fires and downtimes of main fans based on advanced software solutions."

Jan 1, 2019

By A. G. Mattes

This paper presents an overview of passive, engineered, biologically-based anaerobic bioreactor (ABR) treatment systems of the sort that can be used to remove dissolved copper from mine wastewaters. The paper begins with a brief history of the origins of this treatment technology and continues with a discussion of principles of engineered wetlands (EWs, advanced kinds of constructed wetlands, CWs) and the use of vertical sub-surface flow (VSSF) varieties that contain pulp & paper biosolids as the reactive medium for EW cells. A brief outline of a procedural methodology used in evaluating the potential for biological treatment on a site-specific basis is also included. An introduction to the microbiology of passive biologically-based treatment systems is followed by some recent research results in the general area of wetlands and ABR research. The paper concludes with a brief discussion of several sites known by the authors to have successfully (or not) demonstrated the potential of this treatment option.

Jan 1, 2007

By M. Massinaei

Recently constructed circuits have included multiple stages of columns in a variety of applications, from roughing to cleaning. The Miduk copper concentrator (in south-eastern Iran) is one of the unique mineral processing plants which use column flotation cells as rougher. As the bulk of final concentrate is produced by rougher columns, optimized metallurgical performance of these cells is crucial. This paper will present the study and optimization of, a froth washing system of columns. For this purpose, the cross-sectional area of orifices was increased and their orientation altered. Concentrate assay for copper and silica, in addition to bias rate were found to be the assessment criteria. Modification of the wash water system resulted in increasing the purity of rougher and final concentrate. Negative bias and short-circuiting of wash water into the concentrate launder were the main causes of improper froth zone washing in the former system.

Jan 1, 2007

By R. E. Legg

This paper gives a brief outline of the mining and milling methods which will be used on the Stirling zinc-lead-copper ores by Stirling Mines, Limited, who have for the past two years been developing the Stirling mine in Richmond county, Nova Scotia, and who will bring the mine into production in November, 1929. No attempt has been made to give the paper a detailed technical character, for the main reason chat, since base-metal mining is something new in Nova Scotia, it is felt that a general description would be preferable before this Society, whose membership is mainly made up of chose engaged in the coal mining and associated industries. Furthermore, as both mining and milling operations will be governed to a certain degree by the experience gained after production commences, there are many points which cannot be definitely stated now. GEOLOGY Before discussing the mining methods, it is desirable to present a general picture of the geology and occurrence of the ore-bodies. The surface rocks in the vicinity of the mine consist of rhyolites of .pre-Cambrian age. These volcanic flows outcrop in very few places, usually along' the beds of creeks or on the shores of the numerous small lakes. Consequently, a detailed geological map is not available. The exploration work carried out to date has revealed a sheared zone extending through the volcanic flows for a distance of over 1,000 feet. Along this zone, there has been a replacement of the rhyolites by a carbonate rock for widths varying from 50 to 230 feet, and it is in this carbonate formation chat the mineralization at a later date took place.

Jan 1, 1929

By L. Bratek, K. Jaworek, M. Czaplicka

Methods for arsenic compound removal from aqueous solutions include processes such as: coagulation, adsorption, membrane techniques, electrochemical and biotechnology techniques. Advanced oxidation using both UV radiation and strong oxidizing agents such as ozone and hydrogen peroxide may also decompose these compounds. It is known that effluents from metallurgical processes contain inorganic arsenic compounds in addition to the organic compounds such as: dimethylarsinic acid and phenylarsonic acid. This paper presents the conditions that lead to the formation of deposits containing mainly arsenic, such as pH, the wavelength of the radiation and the type of oxidant, for this type of effluent.

Jan 1, 2014

By A. Romero

"Most underground mines require heating or cooling systems to meet health and safety standards in the working areas. In regions where daily or seasonal fluctuations of environmental conditions exist, these systems tend to be over-sized and operate at low average load factors, which increase both investment and operating costs. One possible approach to reduce the temperature variations of the fresh air supplied to the mine, and so reducing the investment in large heating or cooling systems, is to use rock as a thermal regenerator or thermal storage system. Packed rock beds act as thermal inertial units, damping the atmospheric temperature oscillations to provide a more constant fresh air temperature. However, although regenerators exist in some mines, and packed bed rocks have been studied in detail in solar thermal power applications, there is a lack of tools to design new and sufficiently large storage systems of this kind. This work fills the existing gap by presenting a methodology to design and evaluate the impact on the ventilation systems of these regenerators. The method is validated using existing rock bed systems found in the literature and illustrates possible designs for small and large size regenerators in both hot and cold climates.1 INTRODUCTION “ It is quite amazing how often answers to extremely complicated problems can be obtained in this way, by using greatly simplified models of the real situation for the purpose of calculation.” Whiller, A. in private communication to J. S. Stachulak (1989). Motivation Most underground mines located in regions with extreme climatic conditions require the thermal pre-treatment of the fresh ventilation airflows, whether for heating or cooling. Heating commonly is needed in sites with sub-zero temperatures and is usually effected by direct or indirect burning of natural gas or propane. Alternatively, cooling is required in areas with hot temperatures, or in mines with high underground thermal loads where the fresh air at ambient temperature cannot provide enough refrigeration. Thus, when the ambient air conditions cannot provide by itself enough thermal power to ensure safe underground working conditions, a heating or cooling plant is required, which involves a considerable equipment and operation cost."

Jan 1, 2019

The integration of mining and mineral processing technologies into new advanced mining systems is considered to offer several benefits, including selective mining, reduction in waste, increased productivity, flexibility, and improved resource utilization. This paper focuses on underground hardrock mining and the integration of pre-concentration technologies into future mining systems as representing realistic, shorter-term integration options. Control of fragmentation to optimize grinding, pre-concentration of ores, in situ leaching, and modular mining/mineral processing systems are possible with existing technology. Current research is directed toward development of integrated underground systems that minimize surface activity and minimize or eliminate surface waste disposal. Results from a simulation model of an integrated underground pre-concentration system are presented.

Jan 1, 2002

By R. S. Bigelow

Part 1.- Metal Mines Early experiments with mechanical loaders in metal mines were confined largely to machines of the shovelling type and generally air-operated. Although the first application of the scraper to metal mines dates back to 1910, it was not until about twelve years ago that it came to be used extensively. Generally, the scraper gives better results in metal mines than in coal mines, as degradation due to soft bottom and breakage are not factors, but it has a wide range of application and is successfully used in the mining of salt, potash, gypsum, zinc, copper, and a variety of ores, from soft material to hard chunky ore which settles compactly. Today, the scraper has replaced to a large extent the shovelling type of machine in metal mines. Scrapers have offered an inexpensive solution for the mucking problem and are now employed in most mining districts throughout the world. They are operated by labourers of all colours and degrees of skill. Each installation, however, requires individual study on the part of the mine mechanical department to determine the type of scraper, horsepower of hoist, and most economical speed of rope, as well as method of rope rigging. Unfortunately, the scraper has no power to select pay ore from waste and its suitability for use under circumstances which might require sorting of the ore can only be decided by a weighing of the economic factors involved

Jan 1, 1931

By R. L. Brown, E. A. Swanson

THE Buchans ore bodies are located in central Newfoundland, three miles north of Red Indian lake. The townsite of Buchans was named after a Royal Navy Captain who, while attempting to make contact with the Beothuck Indians, camped in the area in 1820. Ore was first found at Buchans by a Mic Mac Indian, Matty Mitchell, who discovered one of the three small orebodies in the bed of the Buchans river. The Anglo-Newfoundland Development Company, which holds mineral rights in the area, developed the orebody, but was forced to give up the venture because of difficulties encountered in separating the various sulphides. The American Smelting and Re-fining Company developed a flotation process which was capable of economically separating and concentrating the various sulphides, and, in 1926, they took a long-term lease on the property.

Jan 1, 1962

By R. D. Lawrence

"Suggestions have been made that the appraisal of mining assets using discounted cash flow techniques should be based solely on proven and probable reserves in reliance upon the widespread international recognition of uniform resource definitions. Following a review of general accepted valuation principles, a survey of the literature and, most importantly, a review of real transactions in the open market, it is clear that valuators should not be constrained by the growing acceptance of modern mineral resource codes. On the contrary, valuation practitioners should be encouraged to examine all classes of mineralization and, after making due allowance for risk, to utilize all mineral resources as a basis for determining fair market value.INTRODUCTIONGreat strides have been made recently in achieving an international consensus on mineral reserve and resource definitions and classifications. The Australasian JORC code, the CIM code in Canada, the SME proposal in the United States and even a proposed code from the United Nations have all brought the objective within reach.Unfortunately, this success has led to another problem for mineral valuators. Certain securities regulators, tax collectors and their ilk have begun to expound on the opinion that discounted cash flow projections carried out to calculate net present values that would form the basis for a valuation determination should be based solely on proven and probable reserves. The author disagrees with this position. This paper examines the subject from four points of view:"

Jan 1, 2003

By B. I. Whittington

This paper examines the effect of cation type (i.e. NH4+, Na+ and K+) and anion type (i.e. SO42- and C1-) on the extraction of nickel during the pressure acid leaching of a Western Australian laterite ore. The results are compared with testwork conducted with other Western Australian nickel laterite ores and the possible process implications of adding an additive to a plant autoclave are considered. Addition of either (NH4)2SO4, Na2SO4 or K2SO4 increased both the nickel extraction and the acid consumption, provided that the level of additive was not too great. For example, the nickel extraction of 93% increased to above 96% in the presence of additives, but decreased to 94% when, for example, NH4 levels increased from 7 kg/t ore to 21 kg/t ore. The relative stability of the jarosite species formed when additives were present influenced the amount of jarosite in the residue and, hence, both the final free acidity and overall nickel extraction. The use of Cl- versus SO42- salts as additives had little effect on overall nickel extraction or overall free acid values, although the presence of SO42- additives appeared to enhance nickel extraction kinetics over the first 60 minutes of the reaction. In contrast, manganese extraction was enhanced by the presence of Cl- additives.

Jan 1, 2004

By H. Chaouki

The aim of this work is to simulate the forming process of a green anode. For this purpose, a nonlinear compressible viscoelastic constitutive law is presented. The concept of natural reference configuration is considered. Within an isothermal thermodynamic framework, a Helmholtz free energy is proposed to take into account the nonlinear compressible deformation process occurring between natural reference configuration and current configuration. A dissipation potential is introduced in order to characterize the irreversible aspect of compaction process. Thus, the constitutive law is formulated through two equations: 1) an expression of Cauchy stress tensor and 2) a differential equation characterizing the evolution of the natural reference configuration. Material parameters are assumed to be a function of the bulk density. This allows capturing the micro-mechanical phenomena within the chosen macroscopic approach. An experimental study based on compaction tests is carried out in order to characterize the mechanical behaviour of the anode paste. A user's material VUMAT subroutine for finite element dynamic explicit analysis has been developed and implemented in the ABAQUS commercial software. To evaluate the model predictive capability, numerical simulations of the compaction forming process of anode paste were performed. Simulation results show that the constitutive law predicts the experimental trends and gives interesting physical responses. This constitutes a first step toward making a benchmark with experimental results on the forming process of anode paste.

Jan 1, 2011

By G. H. Blackwell, N. I. Norrish

"At most operating mines, geostatistical are reserve estimation methods have been implemented by head office or consulting groups . With recent advances in small computer technology it is now possible for a remotely-located mine department to independently implement a geostatistical package.This paper describes the evolution of geostatistical routines to calculate the mineral inventory for porphyry type copper/ molybdenum or similar are bodies. The problems encountered in down sizing the geostatistical routines to run using limited minesite computing facilities are discussed. The high quality of the results, in spite of some compromises to geostatistical theory, is emphasized.The first stage entailed the development of a mineral inventory based on diamond drill data. The difficulties in fitting variogram models to two metals, copper and molybdenum, and the shortcomings of the mineral inventory due to the mixing of lesser quality exploration data with data from more recent diamond drilling are discussed.To improve the ore reserve estimates for short-term planning, a mineral inventory was produced using both the diamond drill and production blast hole drilling data. This inventory, when compared to actual grades, was found to be quite satisfactory for short-term planning. The inventory also provided a reliable data base for long range pit design and financial planning. By regularly updating the mineral inventory, many of the uncertainties of mining a low-grade orebody were minimizedIntroductionThe comparatively low grades of many Canadian mineral deposit s, the escalation of mine operating costs, and the volatility of metal prices in recent years, has required improvements to both short- and long-term mine planning.One of the prerequisites to improved planning systems is the need for accurate grade prediction. This paper describes the on-site implementation of geostatistical techniques for grade estimation of a porphyry I vein type copper/molybdenum ore body ."

Jan 1, 1987

By Damien Gaboury

"Two practical methods for correlating two or more diamond-drill core intersections, using a stereographic projection software are presented. The first may be used to establish if two or more vein intersections are correlative, based on their core angles and diamond-drillhole attitudes. The second method allows prediction of main vein attitudes from numerous intersections, based on a spherical density contouring projection. The methods are suitable for: (1) correlating veins in complex orebodies; (2) ascertaining lateral continuity of ore for reserve estimations; (3) demonstrating the hidden complexity of an orebody; and (4) correlating and interpreting various planar elements.IntroductionModern mineral exploration relies on diamond- drill core data and on the ability of geologists to interpret them. Drill core generally yields unoriented information, unless an expensive orientation device is used. As a consequence, strike and dip of planar elements such as lithological contacts or mineralized veins cannot be determined easily. This is particularly true for blind deposits (covered by thick overburden) and complex orebodies, where field data cannot support drilling interpretations. Such a problem has been addressed previously using two and three diamond drillholes and several solutions were proposed based on trigonometry, and geometric and stereographic projections (Mead, 1921; Wisser, 1932; Fischer, 1941; Stein, 1941; Bucher, 1943; Gilluly, 1944; Addie, 1962; Mills, 1963; Lyons, 1964). However, these solutions are time consuming and not relevant to present day computerized data plots."

Jan 1, 1997

By J. C. Nicholson

The "V" system was first introduced by the West Virginia Coal & Coke Company at their No. 9 mine, Norton. Norton is a small mining village on the B. & 0. railway, about seven miles from the town of Elkins. This year, accompanied by G. D. MacDougall, I visited this mine to obtain first-hand information regarding this modem system and to determine its adaptability to conditions in Nova Scotia. The following is a brief account of my observations. The seam that is being worked is known as the Lower Kittaning, which, at this point, has an average thickness of 7 feet. This includes a band of hard clay varying in thickness from 8 to 14 inches, which occurs about 2 feet from the pavement, also 8 inches of inferior coal at the roof. The latter is not recovered, which leaves to be mined about 5 1/2 feet of clean coal. The roof is slate and shale for the first 30 feet, followed by 40 to 60 feet of sandstone; the total cover is from 80 to 250 feet thick. The seam lies very flat, with a dip of only 2 per cent., and, as the dip is toward the main entrance, it' is in favor of the load, also providing natural drainage for any water the mine makes. As the mine is not gassy, and there is no water to be pumped out, one can understand that mining conditions are practically ideal.

Jan 1, 1924