Search Documents

By R. Boom

Corus Umuiden, formerly Hoogovens, was the first steel plant in Europe after Voest to introduce oxygen steelmaking. In the decision-making process contacts with Dofasco in Canada about the production of formability steel grades were crucial. In developing oxygen (LD-) steelmaking high liquid steel output rates had to be combined with accurate process control. For ingot casting static models with input control and sampling during interrupted blowing were sufficient to deliver liquid steel within the required carbon, phosphorus, sulphur and temperature windows. Computers were introduced to perform the complicated charge calculations. Continuous casting called for strict control of composition and temperature at process end point and made predictable timing crucial. Dynamic control was introduced based upon sub lance measurements and waste gas analysis. Reliable disposable measurement sensors were developed in a concerted international action. Dissolved oxygen at blow end deteriorated the quality of low carbon aluminium killed steel grades. Blowing gases through the converter bottom improved process kinetics, resulting in lower carbon-oxygen products, yield increase and better phosphorus removal and generated new families of hybrid blowing processes. Introduction of secondary metallurgy facilities such as argon stirring stations, vacuum degassers and ladle furnaces relieved the demands for strict BOF end point control. Desulphurisation of hot metal became standard practice. In regions with scrap shortage hot metal desiliconisation followed by dephosphorisation, was introduced in the blast furnace cast house and hot metal transfer ladles. Later redundant converter vessels were used for pre-treatment, resulting in a two-stage process. The fundamentals of oxygen steelmaking are described and a vision on the future is presented.

Jan 1, 2004

By T. A. Rickard

FROM AN OLD MANUSCRIPT THE text for this contribution to the history of the Patio process is a page taken from a Spanish manuscript of Bartholomé Arzaj Sanches y Uela, now in the possession of the library of Brown University (see Figure 1). I owe the photographic print to the courtesy of the librarian. The date, as will be seen, is 1577. The subject is the treatment of silver ores at Potosi, in old Peru, but in modern Bolivia. The group of drawings (see Figure 1) is entitled "Arrangement of the machines in which the ores of silver are ground on the bank of Potosi, the one of two batteries and the other of one". First, top-left, we have the sketch of a "machine of one battery" operated by a water-wheel. From this mill the water runs in part along an aqueduct supported by pillars to the two-battery mill and in part down the hillside, where men are at work with "tubs, which are called cochas, in which are washed the charges of ore and amalgam". Along the top of the page are shown the "various offices in which are stored the copper, the salt, the ucha [llama dung, used for fuel], the lime, and other materials for the re-duction of the ores". To the right of these are "apartments and warehouses in which is stored the ore brought down from the mountain"?the cerro de Potosi. Through the arched portal come the "sheep [llamas] on which is brought down the ore". To this is added a reference to "the second gate, which closes the whole works". On the level above the aqueduct are seen six men carrying skin-bags that contain water. This is being sprinkled on the ore. On the extreme right are six more of these water-carriers. Next comes the two-battery mill. The mortero, or mortar, is marked on the right. Another description says, "Stone, on which the stamps crush the ore, which is called a mortar". To the left of these are indicated "screens of wire in which the ore is sifted after it has been crushed". Farther to the left, near the ore-washers, is a "shed, in which is placed the metallurgist to test the ore of the boxes". Along the left side of the page are sundry buildings, one of which is labelled a "shed in which are placed the cones of silver". Near it, lower, to the right, is the "furnace, in which are roasted the sulphides to facilitate treatment". Farther to the right is the "place where the Indians mix the charges of sulphide ore, which is called a buitron". Alongside is a "buitron in which the charges are prepared for reduction". Inside is a container, to which are attached the words "measure, called topo" On the extreme right is "another buitron in which the Indians mix the ores with their feet, as well as the heaps for the preparation of the reduction". Near the bottom, on the extreme left, is the "chapel where the holy sacri¬fice of the mass is celebrated". Under the first buitron is the "place where they dry the moist ores, called pãpear".

Jan 1, 1935

By B. P. Simser, R. K. Brummer, A. Mortazavi, P. P. Andrieux

"A large-scale panel destress blast was fired at Brunswick mine in the fall of 1999 in order to reduce the ground stresses in a critically important neighbouring mining region. This work, sponsored by the Mining Division of CAMIRO and Brunswick mine, consisted in heavily choke-blasting — and subsequently leaving in place — a massive waste sulphide pillar in the southwest end of the 1000 m level. This paper describes the approach and design methodology used to try to maximize breakage in the rock mass in the area to destress, while minimizing damage to critical infrastructures in the vicinity. The loading operations, as well as the results of the blast — in terms of its field performances, as recorded by near-field blast vibration monitoring equipment, visual postblast assessments and measured impact on the regional stress field — are discussed as well. A brief comparison between the measured stress changes and inelastic numerical modelling of the test site is also presented.Un tir à grande échelle de relâchement des contraintes dans un pilier a été effectué à la mine Brunswick à la fin de l’automne 1999 dans le but de diminuer les contraintes de terrain dans une très importante zone de production adjascente. Ces travaux, financés par la division minière de CAMIRO et la mine Brunswick, consistaient à tirer violemment sans aucune face libre, et à laisser en place, un pilier de sulphures massifs au sud-ouest du niveau 1000 m. Cet article décrit l’approche et la démarche conceptuelle utilisées pour tenter de maximiser les fractures dans le pilier visé, tout en minimisant les dommages collatéraux à des infrastructures critiques se trouvant dans les environs immédiats. Les opérations de chargement des explosifs et les résultats du tir — en termes de ses performances, telles qu’évaluées par de l’équipement de monitoring rapproché des vibrations de tir, d’observations visuelles, et de son impact sur les contraintes de terrain locales — sont également discutés."

Jan 1, 2003

By Justin S. Johnsen

As OEM sensors and interfaces have grown in number, the available data from equipment in the mining environment has continued to multiply. This equates to an increased visibility of operating performance, mechanical and electrical health, and predictive monitoring that can directly improve maintenance reliability and scheduling. With increased visibility, where should a reliability engineer begin to look to directly impact Capacity Assurance? More specifically, what source will provide inputs to the Failure Modes Effects Analysis (FMEA)? Results from these analyses must be documented, and they must contribute to the overall mission of the mining company; these results must reduce costs and increase profits. Through detailed data capturing, documenting, and analysis, Modular Mining Systems? Time Tracking application, used in the MineCare® maintenance management solution, can drive decisions and provide direct impact to engineering projects for continuous improvement in the mine maintenance organization.

Nov 1, 2011

By Douglas A. Grieg

THE EXCUSE for producing still another paper dealing with the oilfields of the Middle East is the overwhelming importance of this area to everyone, both inside and out of the oil industry. Figure 1 shows the area defined as the Middle East for the purpose of this paper. No description of what constitutes the Middle East is generally acceptable to everyone and, in fact, in many parts of the world it is referred to as "Western Asia". At the time ?the writer went to work as a geologist in the Middle East -this was in 1926 -there were just three known oilfields, namely, Hurghada in Egypt, Naft Khaneh in the Transferred Territories of Iraq, and Masjid-i-Sulai-man in Persia. Their combined producing rate at that time was around 100,000 barrels per day. Toda y, just thirty years later, some forty-two fields have been proven to exist, and a recent discovery in Syria -if commercial -may add one more to the list. Producing rates at the end of last year ( 1956) were approaching four million barrels per day. This sizable figure re presents nearly 23 per cent of the total Free World's production. What is more important still, something over 70 per cent of the Free World's proven oil reserves are known to exist in the subsoil of the Middle East.

Jan 1, 1957

By Norman Marr

Introduction In Canada, the mining industry and water-power development are intimately associated in that mining, which ranks second among the country's primary industries, depends principally upon hydro-electric energy for its large power requirements. On the whole, the Dominion has been very favourably endowed with water-power resources; generally speaking it is a well-watered country with numerous rivers and lakes located in are as where the topography favours water-power development. Precipitation, the raw material of water power, varies from an annual fall of more than l00 inches on the Pacific coast to about 12 inches in sections of the Prairies and the Northwest Territories; in Ontario and Quebec the annual average is 24 to 40 inches and in Nova Scotia about 45 inches. In its descent to the sea, the resulting run-off, much of it from considerable altitudes, creates sources of potential energy at every rapid and fall along the country's many streams and rivers. Many of the innumerable lakes in the Dominion provide storage basins for the regulation of stream flow, thus enhancing the potential power of available sites. While water-power resources are fairly well distributed across the Dominion, as is shown on the accompanying map of Canada showing power sites (Figure 1), it is particularly fortunate that those areas which are lacking in indigenous fuels have been compensated in large degree for this scarcity by being favoured with a high proportion of the total potential water power. This has an important bearing on the mining industry in that extensive mining operations can be economically carried out in the great Canadian Shield, which is lacking in commercial coal deposits but is rich in water-power resources. This Precambrian formation, which forms a wide belt around Hudson bay and in which many metalliferous ores are found, was 'subject to severe glaciation in a recent geological period, so that its river systems are comparatively young and are characterized by numerous lakes joined by short reaches of fast water, rapids, and falls which offer frequent opportunities for power development. The western Cordilleran region, which also is important in mining, has abundant water power. The accompanying geological map (Figure 2), prepared by the Geological Survey of Canada, shows the great extent of the Precambrian and Cordilleran regions and may be compared with the map of water-power sites to show the high incidence of water-power resources in these potential mining areas in which important mineral discoveries have already been made.

Jan 1, 1949

By J. T. Chen, S. Winkler, M. J. Worswick, O. Orlov

This paper presents a review of research conducted at the University of Waterloo concerned with the application of aluminum alloy sheet and tube in automotive structures and body panels. The research has focussed on formability prediction and results using a range of damage-based formulations. These models include continuum-level damage approaches and, more recently, a so-called percolation damage approach intended to capture microstructural heterogeneity effects on damage development. This paper presents applications of these damage approaches to simulate formability of experiments considering stretch flange panels. The experiments consider drawbead effects associated with the bend/unbend deformation as the material flows through the drawbead. Recent work on simulating in situ X-ray tomography experiments that capture damage evolution during tensile deformation will also be reviewed.

Jan 1, 2006

By Susumu Tsubota

Three types of reference gold catalysts, i.e., 3wt%Au/TiO2 (Au-Ti: Type A), and 0.3wt%Au/Fe2O3 on alumina beads (AUS: Type B), and 5wt%Au/Fe2O3 (Au-Fe: Type C), were produced in a test plant scale by Sud-Chemie Catalysts Japan, INC. under the licensing of AIST. To evaluate the validity of the preparation methods and conditions used for the reference samples, elemental analyses by ICP, particle size measurements by TEM, and catalytic activity measurements for the oxidation of CO and H2 over these catalysts were made. Gold catalysts can be prepared in a large scale of ca 400g for the Au-Ti and Au-Fe catalysts, 5 kg for the AUS catalyst with good reproducibility. It was confirmed that they were available for useful as the reference gold catalysts of World Gold Council.

Oct 1, 2003

By J. Flemming, R. O. Burt

"The Tanco pegmatite is located in the Bird River greenstone belt of southeastern Manitoba approximately 160 km northeast of Winnipeg (Figure 1). This pegmatite body was discovered in 1929 and subsequently attempts were made to exploit it for tin by Jack Nutt Mines Ltd. and later in the middle 1950's by Montgary Oil Ltd., who extensively developed but did not produce from, its lithium deposits. In 1966 systematic investigation of the pegmatite as a potential source of tantalum led to the founding of Tantalum Mining Corporation of Canada Ltd. (TANGO) in 1967 and production of tantalum concentrates from the Bernie Lake mine commenced in 1969. Tanco is currently jointly owned by Hudson Bay Mining and Smelting Co., Cabot Beryl co Inc. of Boston, and the Province of Manitoba. (Williams and others 1978, Burt 1979, Burt and others 1982), continued until the end of 1982, when, due to falling demand and prices, operations were suspended.During the 1970's Tanco had investigated the potential of the lithium orebody; carrying our research into both the concentration of the ore and into the production of lithium chemicals. However lithium chemicals were in an over-supply situation, due in part to the production from Chilean brine deposits (Buckley, 1983), and Tanco' s own plans were put into abeyance. The potential alternative market, the direct use of concentrates in the glass and ceramics industry, did not at the time justify the cost of constructing a new plant."

Jan 1, 1986

By F. R. Jones, B. W. Taylor, A. R. MacPherson, L. J. Lamb

"The Lake St. Joseph Iron Deposit is in Northwestern Ontario. Exploration to date by Steep Rock Iron Mines Limited has indicated an ore reserve of 683 million long tons. Metallurgical investigations have proved that suitable oxide pellets and/or superconcentrates can be economically produced from this ore. Studies of the Lake St. Joseph iron ore deposits have covered the period 1956-71, and have embodied applications of the improvement in mining and processing technology over this period. Market demand in the early 1960's for high-grade oxide pellets as a replacement for natural iron ores for the blast furnace first drew attention to the potential of the Lake St. Joseph deposit. The current market trend toward utilization of sponge iron to replace steel scrap as feed to electric furnaces and cupolas now suggests that the deposit can better be exploited as a prime source of superconcentrates."

Jan 1, 1972

By Mohsen Mohammadi, Edward Cyr

"To date, several studies have been performed on the static mechanical properties of SLM-AlSi10Mg alloy. There have also been more recent studies on the relation between scan strategy, texture, and mechanical properties of SLM metals and composites. However, there is a huge knowledge gap in the available literature regarding texture and mechanical behavior of SLM-AlSi10Mg alloy under high strain rates. Therefore, in this study, dynamic mechanical behavior of AlSi10Mg_200C alloy manufactured by DMLS technique was investigated at high strain rates ranging from 900/s to 1700/s using Split Hopkinson Pressure Bar. Texture using X-ray diffraction technique of the initial samples were measured. The yield strength, peak flow stress, and ductility increased in all samples with increase of strain rate. TEM studies have also revealed evidence of continuous dynamic recrystallization in grains after 900/s–1700/s strain-rate tests. A Taylor polycrystal crystal plasticity constitutive model was then developed to capture and predict the texture evolution and mechanical response under dynamic loading, using plastic work as a critical parameter for the onset of recrystallization.INTRODUCTION Additive manufacturing (AM) powder techniques are among the fastest advancing breakthroughs in manufacturing in recent years, defined by a bottom-up layer by layer process of joining with energy input from lasers or electron beam (Herzog et al., 2016; Gibson et al., 2015). Among alloys fabricated by SLM, AlSi10Mg is of high interest to industry and academia due to its low density, high specific strength and excellent corrosion resistance, making this alloy a viable contender for aerospace, automotive, and marine applications. Circumstances such as car crash or bird aircraft strike hazards subject potential additively manufactured AlSi10Mg parts to impact loadings. This drives an interest in understanding and predicting dynamic behaviour of these alloys. AlSi10Mg is the AM counterpart of A360 die-cast aluminum, which possess hypoeutectic microstructure (Li et al., 2015). Up to the present time, many studies have presented the mechanical properties of SLM-AlSi10Mg alloy. The mechanical properties and microstructure of AlSi10Mg produced by selective laser melting (SLM) or DMLS techniques can be controlled using different parameters, such as feedstock powder (Asgari et al., 2017), and process parameters (Olakanmi et al., 2015). The microstructure and mechanical properties of AlSi10Mg can also be controlled using post heat treatment after SLM process Li et al., 2016). The mechanical properties of SLM-AlSi10Mg are sensitive to strain rate and can both change under quasi-static (Rosenthal et al., 2017) and high strain rates (Asgari et al., 2018). However, a significant knowledge gap in available literature regarding modeling these behaviours, and especially micromechanical modeling of dynamic behaviour."

Jan 1, 2018

By CIM Environmental, Social Responsibility Society

Within the mining industry, the pathway from exploration, to planning, construction, operation and closure has become more complex over the last few decades. The current financial, environmental and social influences present the mining industry with unprecedented challenges and opportunities. In addition, international environmental and social reporting standards and codes are becoming increasingly robust. The reporting requirements provide an added impetus for issuers to effectively manage environmental and social impacts and risks. Reporting requirements also provide the opportunity to be transparent. The intended audience for these Environmental, Social and Governance (ESG) Guidelines for Mineral Resource and Mineral Reserve Estimation includes practitioners, industry participants at all levels of skill and experience, corporate management and board members, government agencies, academic institutions and interested parties. For practitioners, this document provides underlying key principles of environmental, social and governance practices. The ESG Guidelines provide guidance for those using environmental, social, governmental and governance information when preparing and implementing mineral exploration programs and contributing to the preparation of mineral resource and mineral reserve estimates for mineral properties that are either at the study stage (i.e., scoping / preliminary economic assessment, pre-feasibility, or feasibility studies) or in operation. The guidelines can also be used to help mineral resource and mining companies apply good practice to manage their environmental and social risks and opportunities. Companies can identify and retain appropriate professionals to prepare environmental and social materials to support company studies. The guidelines are also a resource for companies developing effective environmental and social management strategies at any project stage. This document is not intended to be prescriptive and is not intended to provide exhaustive guidance on what to consider in terms of environmental, social, legal and governmental modifying factors in the preparation of MRMR estimates. Rather, it is intended as general guidance to assist companies and practitioners in considering and applying these modifying factors for MRMR estimates. This document is also not intended to guide environmental and social impact assessment (ESIA); however, the measures needed to manage impacts help inform the constraints and costs for defining mineral resources and mineral reserves and inform the costs and schedules of mineral project studies. All documentation of MRMR estimates made by an issuer and intended to be, or reasonably likely to be, made available to the public in a jurisdiction of Canada must comply with the requirements of National Instrument 43-101 Standards of Disclosure for Mineral Projects (NI 43-101), as amended from time to time (Canadian Securities Administrators, 2016a and 2016b). Disclosure is not addressed in these ESG Guidelines. Determination of what to include in disclosures is defined in the applicable Securities’ legal frameworks. Appendix A presents a summary table showing the linkage of the principles and topics in these ESG Guidelines to the potential effects on project costs, schedules, government permits and approvals, social licence to operate and financing.

Sep 8, 2023

By Norman A. Jull

"Factors which affect the separation achieved in a hydrocyclone are discussed and illustrated with graphs of some mathematical relationships.Definitions of separation and sharpness include comment on use of elutriation devices.A plea is made for better evaluation of field data prior to their reporting or use in calculations. Methods of evaluation are suggested, with samples of the relevant calculations.An example of the effect of percent solids errors is given, with computer printout and plotted corrected recoveries.INTRODUCTIONThe range of interest in cyclones runs from a simple demand for classification results to a detailed study of published equations defining cyclone characteristics. Probably this group covers as broad a range and, in an attempt to offer something for everyone, I will begin with general operating comments, then move on to more analytical topics. Ideally, an author would compose his paper after the discussion period, when he would have a better idea of the areas of special interest to his audience.Sor'1e of you may share our incurable fascination with classification, especially as performed in cyclones. It is amazing that such a simple device could be in use for more than 20 years and retain as much mystery as it does. Substantial parts of the mystery have been solved but some remains, to keep up our curiosity. There is at least one valid reason: the unusual compactness of this device, which makes internal observation very difficult. What other unit can you think of which performs such a complex separation between particle sizes, shapes and specific gravities at such high capacity? Retention time in a cyclone is typically 3 seconds!Mutual Agreement - In a cyclone, every parameter of geometry and of operation interacts with every other. In an orderly discussion of individual parameters it would be necessary to repeat, in every section, 11 if all other factors are equal"". Could we agree now, for our mutual convenience, that that phrase is clearly understood between us during the remainder of this paper?"

Jan 1, 1972

By Bob Robinson

In 1990, the European Space Agency (ESA) initiated a technology transfer program to stimulate the wider use of technology developed by the European and Canadian space communities. This paper focuses on the method of technology transfer from the space industry to terrestrial industries, with a focus on the mining resource sector within a program called the Harsh Environments Initiative (HEI) created in 1997. Other resource sector applications include forestry and oil & gas. C-CORE in partnership with the Mining Innovation, Rehabilitation and Applied Research Corporation (MIRARCO) supported by ESA, Canadian Space Agency (CSA) and European R&D organizations conduct projects to promote and demonstrate the transfer of innovative technologies from space to non-space industries. Space programs have and continue to develop new knowledge for extra-terrestrial application, e.g., satellite earth observation, manned missions and unmanned planetary exploration. Many of which hold the potential for application on land and ocean. Currently, space technologies of interest to the mine sector range from robotics and image analysis to sensors, software and advanced materials. The HEI works to identify and apply these types of technologies in the areas of automated/tele-controlled mine operations and mine monitoring.

May 1, 2001

By E. H. Smith

"The El Indio mine treats a complex mixture of copper and gold/silver ores at its plant located in the high Andes in Chile. The plant utilizes conventional crushing, grinding and flotation to produce a copper/gold/silver concentrate. Due to high levels of arsenic and antimony, the flotation concentrate must be roasted prior to custom smelting. The flotation tailings is leached and additional gold recovered from a CIP circuit. Present and future metallurgical developments are discussed in this paper. INTRODUCTIONIn late 1989, LAC Minerals purchased 65 % of Bond International Gold and as a result became controlling shareholder of the El Indio Mine through Bond and San Jose.El Indio is a world class, complex sulphide gold deposit located in the hydrothermal alteration belt of the Andes mountains in the 4th Region of Chile. The mine is located in the high Andes about 185 km east of La Serena at an elevation of 4000 meters. The 1450 workers at El Indio live in the mine camp at 3200 m and on days off are bussed to La Serena.The El Indio mine was started in 1979 by St. Joe Minerals Corp., bought by Bond in 1987 and subsequently by LAC in 1989. The mine has produced 2.7 million oz. of gold, 9.5 million oz. of silver and 170,000 t of copper since start of operation. The mill is currently operating at a rate of 2850 t/d and producing a copper/gold concentrate which is roasted to produce a copper/gold calcine and high quality, saleable crude AS2O3 . A small proportion of the precious metals are also produced as bullion from the leach circuit.Total production during 1989 was 224,197 ounces of gold, 1,309,342 ounces of silver and 26,968 tonnes of copper. The average cash cost of production for the period was U.S. $96 per ounce of gold, net of by-product credits. The average realized price was $5. 30 per ounce of silver and $1.14 per pound of copper."

Jan 1, 1991

By M. J. Michaud, M. J. Lavigne

"A cornerstone of any successful mining project is an understanding of the mineral assemblage and metal distribution comprising the deposit. Knowledge of the precise mineral/ metal zoning enables an operation to utilize different mining and processing methods optimized for different parts of the deposit. The Lac des Iles mine, located in northwestern Ontario, is one operation that depends on a good understanding of these issues. Current resources for the Roby Zone total 94.1 Mt grading 1.66 g/t Pd, 0.18 g/t Pt, 0.14 g/t Au, 0.062% Cu, and 0.053% Ni.The Roby Zone occurs within the gabbroic portion of the Lac des Iles intrusive complex and consists of three compositionally and texturally different ore types with variable PGE, base and precious metal contents. PGE occur as sulphides and bismuthotellurides in net-textured sulphides, coarse sulphide blebs and as finegrained inclusions within secondary silicates.Knowledge of the precise mineral/metal zoning has directly and indirectly improved several operational aspects, including resource modelling, mining, and processing. For example, metallurgical recoveries have been increased by up to 3% to 5% and concentrate grades have increased by up to 100%. IntroductionLac des Iles Mines Ltd., a wholly owned subsidiary of North American Palladium Ltd., owns and operates a 3000 t/d open pit mine and concentrate facility, located 100 km north of Thunder Bay in northwestern Ontario. The Lac des Iles PGE-gold-copper-nickel mine has been in commercial production since 1993 and in 1997, produced 1.8 million grams of palladium, 127 000 g of platinum, 114 000 g of gold, 438 000 kg of copper and 354 000 kg of nickel (North American Palladium Ltd., 1998).Under the Industrial Research Assistance Program (IRAP), a two-year study of the mineralogy of the Roby Zone was undertaken with a goal of improving the profitability of the mine. Geological mapping, petrography and geochemistry of the Roby Zone were completed during this study. Utilization of the detailed mineral/metal zoning identified as part of this study was implemented at the mine and shown to positively impact many operational aspects including mining and processing."

Jan 1, 2003

By C. B. Webber, W. A. Grell

"Sherritt Gordon's Ruttan Mine is a copper-zinc operation located approximately 600 miles north-west of Winnipeg. Open pit mining began in 1973 at 10,000 Tpd., with a change over to underground mining in 1981 producing 7,500 Tpd. Ore is crushed to -3/4"" followed by rod and ball mill grinding (two ball mills in series), differential copper-zinc flotation, and dewatering. The copper and zinc concentrates are trucked 75 miles to Lynn Lake, where they are shipped by rail to the HBM&S smelter at Flin Flon.This paper describes a method used to predict the effect of grind particle size on metallurgical performance, as well as details on the copper and zinc metallurgical performance due to fine grinding in actual plant operation.Initial statistical studies on historical data (including ore source, head gr3de, grind, etc.) indicated that copper and zinc recoveries increased with fineness of grind, in the range of 50 to 65% -200 mesh.In order to extrapolate beyond 65% -200 mesh, and to develop expected nonlinear relations between grind, Cu concentrate grade, and recovery, the assays of screen fractions of copper concentrate and tailing were used to determin8 the relation between net smelter return (a function of grade and recovery) and grinding cost. The optimum economic grind would be that grind at which the net smelter return less grinding cost reached a maximum."

Jan 1, 1982

By Oyku Selimoglu

The key to successful mine production plan and subsequent operation is efficient mine layout design and optimization. Pit layout design and optimization allow the delineation and extraction of mineable reserves and the minimum waste subject to slope stability, economic, quality and quantity constraints. Many design and optimization software packages have been developed to aid this intensive and challenging process. These packages include VULCAN, SURPAC, DATAMINE, GEMCOM, MICROLYNX, MEDSYSTEM and MINESIGHT. These software packages are developed as integrated computer-aided systems used for database creation, survey, geological and geostatistical modeling, mine planning and production optimization and environmental modeling. In Turkey, many mining companies still plan and design mine layouts with traditional hand methods. In this study, VULCAN has been used to design and optimize the Eti-Bor A.S. Kestelek Boran Open Pit Mine in Western Turkey. The main objective is to show the company the superior advantages of mine planning software for designing and optimizing mine layouts over the traditional hand methods. Drill hole data used by the company to estimate the reserves for planning are used in this study. The ore grade varies between %1,04 B2O3 to %47,33 B2O3. The pit toe and crest strings are projected using variable batter angles and berm distances. On the north side, batter angle is 180 and berm distance is 25 meters, on the south side, batter angle is 320 and berm distance is 15 meters. In addition to that open pit bench height is 10 meter. The concepts of block modeling are applied to the Kestelek open pit mine with detailed ore grade modeling for each block. The Lerchs-Grossmann?s algorithm is used to optimize this mine based on the block model, the economic block values for each block and the underlying field constraints. The results from VULCAN were similar to the estimates by hand. The reserve estimates from VULCAN is 13,192,870 tons compared with the hand estimate of 13,200,000 tons, overburden estimates of 15,622,889 m3 compared with 15,000,000m3 obtained by hand with a stripping ratio 1.18:1 (m3:ton) from VULCAN versus 1.14:1 (m3:ton) from hand estimate. Vulcan improves the efficiency, speed and reproducibility of the planning results. It provides mining engineers, geologists and surveyors with a cost-effective modular system for assessing and planning the mine layouts. Furthermore, Vulcan?s specific modules allow efficient access and manipulation of databases, open pit mine design, block models, optimized 3D mine layouts, and more. However, for competitive business in Eastern Europe, VULCAN should improve its software support. Effective training, help desk support systems and nearby distributors with just-in-time solutions to company problems will generate competitive business for VULCAN.

May 1, 2007

By A. F. Banks

"Potash processing has much in common in terms of unit operations and plant operating strategy with other mineral processing plants. As it is a rather large topic the processes will be broad brushed to give you some background and then I will go into a little detail on the things we do in the Cominco plant that may be of interest to the group as a whole. In particular the centrallized computer control system and associated instrumentation and the operator training programs will be covered as well as the mill fire, something that could happen in any plant. THE ORE AND PRODUCTSThere are differences in potash ores as you would expect. It is my intention to deal with the ores processed in the Saskatoon area. These are mined from the beds in the Patience Lake Member and have a mineralogical description as follows:Sylvite (Potassium Chloride) 40%Halite (Sodium Chloride) 55%Insolubles (Slimes) 5%A number of products are made from this ore. It is characteristic of a potash plant that you put as much effort into grading and converting the sylvite to meet market requirements as you do in recovering it."

Jan 1, 1976

By T. Binnert Haites

INTRODUCTION NUMEROUS examples of troubled zones, interfering with the normal development of coal seams, have been cited in the literature. From a geological point of view they can be subdivided into structural and sedimentary troubles. Of the latter type, wash-outs are usually the most bothersome. Some years ago, A. A. Thiadens and the author arrived at the conclusion that they represent fossil river-beds. A method of predicting the course of these rivers was developed, which has been successfully applied in the Netherlands coal measures, and more recently by P. Stassen in some of the Belgian coalfields and by the author in the Sydney coalfield. The Sydney coalfield has long .drawn the attention of geologists, and three main periods of systematic geological research may be distinguished. The first period, 1872-1900, is covered by the studies of Ch. Robb and H. Fletcher (32, 10-13) (1). Their detailed sections of the cliffs have lost nothing in value, and are frequently consulted today.

Jan 1, 1951