Search Documents

Mill liners provide the wear-resistant surface within grinding mills, they also impart motion to the mill charge, ie the grinding process, by providing the key between the charge and mill shell, and, at the discharge end, they remove the ground contents of the mill. As semi-autogenous grinding (SAG) mills have grown in size the process aspects of liner design and their impact on mill performance have become particularly important. While feedback from practical experience is critical to good mill liner design, increasingly sophisticated computer-based tools are being developed to assist in mill liner design.

Jan 1, 2007

By Toomey P. T

In many open cut coal mines, rivers and large creeks can cause planning and operating difficulties, both in the terms of the more obvious location of the current watercourse, but, and sometimes more importantly, past meandering of the watercourse. Prevent and past flow regimes may have deposited large alluvial sequences within the current mining areas. The presence of groundwater within the alluvium further complicates the planning and operating practices.A situation exists at Saraji Mine in which alluvial sediments overlie a massive sandstone sequence which in turn lies at about one metre above the coal seam. The problems encountered include high levels of groundwater ingress to the pit, highwall instability, and an unacceptably high rate of blast hole collapse (prior to charging with explosives). Other aspects of the dragline stripping operation were also affected.

Jan 1, 1992

By Whitworth NR, Fox MJ, Henley RG

The coal mass flow monitor was developed to measure the instantaneous mass flow rate of pulverised coal to the copper reverberatory furnace at Mount Isa. The instrument was calibrated with an isokinetic coal sampler which was installed immediately downstream from the coal mass flow monitor. Readings from the coal mass flow monitor were used to control the feedrate of coal to the furnace and this helped to stabilise the furnace operation.Coal samples obtained from the isokinetic coal sampler were also sized using a Leeds and Northrup Microtrac analyser. The coal size was critical to reverberatory furnace performance. These developments significantly improved the overall combustion control of the furnace and gains of ten percent were made in the furnace thermal efficiency. Testwork on an auxiliary arch coal burner is also reported.

Jan 1, 1985

By Yuanping H

There is a practical method of handling methane in a fully mechanized high output coal face when the methane outflow rate from the face is too high to be handled by ventilation alone, a combined method would be adopted. Before adopting this method, above all, the sources of methane outflow, which can be divided into methane in the intake airflow and methane emitted from the working seam and from the worked-out area, are determined by air-methane measure- ments in the tail gate and intake conveyor gate or by air-methane measurements in the working space of the coal face. Then, in

Jan 1, 1988

By S Morrell, D Clark

æMine to MillÆ improvement involves optimising the chain of rock breakage processes from the in situ rock in the mine to the output of the concentrator. A growing number of paper studies and case histories from metalliferous mines (AusIMM, 1998; JKMRC, 1998; Clark and Scott, 2002) demonstrate that generating more breakage in the pit and the primary crusher can lead to benefits to milling that result in significant improvements to the economic performance of a mining project. However, unless the ævalueÆ of doing this (benefit over cost?) can be appropriately quantified, the approach cannot be effectively managed and the increases in blasting and monitoring costs cannot be justified.Mining operations have traditionally been organised into the separate departments of geology, mining and processing based on the specialist skills required and the different professional disciplines involved. Process optimisation across these boundaries has commonly been frustrated by management requirements to minimise the costs incurred by each department without adequate reference to the ævalueÆ being created. Companies have tended to discard positions that provide a technical over-view of the value chain, reducing the number of people with the opportunity to influence practices across these process boundaries.This paper discusses these issues and identifies measures required to quantify and manage the ævalueÆ provided by æMine to MillÆ improvement generated by the intense blasting of ore.

Jan 1, 2002

Violarite, (Ni,Fe) 3+x S4, is a ubiquitous secondary mineral in the supergene alteration zones of massive nickel sulphide deposits in Western Australia. It is formed by the pseudo- morphous replacement of pentlandite, pyrrhotite and/or millerite, and retains the textures typical of these precursors. Although the composition of the first-formed violarite is related to that of its precursor, supergene enrichment results in an increasing nickel:iron ratio toward the top of the supergene profile. In pentlandite-pyrrhotite ore, the replacement of pentlandite by violarite releases some nickel, which is consumed by the partial conversion of the pyrrhotite to iron-rich violarite. In pentlandite-millerite ore, on the other hand, the pentlandite, on conversion to violarite, appears to release excess iron that participates in the partial conversion of millerite to nickel- rich violarite. The characteristic textures exhibited by the secondary violarite and its replacement products in supergene and gossanitic deposits overlying massive nickel sulphide ores generally enable the original mineralogical compositions of the primary ores to be inferred.

Jan 1, 1973

By Glastras M. V

The presence of arsenic in solutions which result from the processing of many sulphide minerals leads to a need to understand its speciation in aqueous systems and the reactions of those various species. This paper deals in particular with the precipitation of arsenic from aqueous solution in the form of insoluble inorganic compounds in order to remove arsenic from various hydrometallurgical process streams. The solubility and stability of the precipitates is examined. It has been found that many of the arsenic compounds presently used are more soluble than previously accepted and unstable in disposal sites such as tailings ponds.

Jan 1, 1987

By Pollard D. M

The effects of pH, temperature and the form of zinc used on the kinetics of cementation of cadmium from process liquors were investigated. Batch tests were conducted in stirred beakers, and the cementation reaction was found to be first order controlled. The rate controlling step was thought to be the diffusion of zinc ions from the zinc surface to the bulk solution. The pH was found to have a significant effect when using Prime Western zinc or zinc dust. High reaction rates were favoured at low pH levels and a minimum rate was observed at a pH level of approximately 5 to 5.5. The pH was found to have little effect when using high grade and cathode zinc. The reaction rates increased significantly with increasing temperature; a reaction temperature of 55¦C resulted in almost complete removal of zinc from solution. Effective cementation rates were only acheived with cathode zinc after pickling in acid. The nature and specification of zinc used determined the cementation rate of cadmium, resulting in the following order: 1. Zinc dust 2. Prime Western zinc at pH 3 3. High Grade zinc at pH 3 4. Pickled cathode zinc 5. Prime Western zinc at pH 3 6. High Grade zinc at pH 3 7. Cathode zinc "as received".

Jan 1, 1989

By Ren T. X, Jozefowicz R

In many branches of engineering, there has to be an understanding of the motion of fluids in order to solve problems. Many safety and health problems in the mining industry are typical examples that involve the understanding and analysis of fluid flow, such as explosions, the spread of fires, dispersion of gas and dust, and ventilation patterns. Computational Fluid Dynamics (CFD) is concerned with the use of computers to produce information about the ways in which fluids flow in given situations. Until recently CFD has been widely applied to a variety of industrial sectors and increasingly to problems in the health and safety areas. With the arrival of more powerful computers and CFD packages, CFD techniques are no longer practised solely in a research environment, but can be used by engineers in many industrial fields. This paper introduces the basic concepts and general procedures involved in the use of CFD technology. A comparison is given as a guide to the major features of a number of widely used commercial CFD codes. Areas of potential CFD applications are identified in a range of safety and health problems in mining industry. An example is presented to illustrate the use of this technology. It is believed that the exploitation of these areas using CFD approach will contribute significantly to the solution of today's many mine health and safety problems.

Jan 1, 1995

By Clark I, Stockton N, Warren L

Nickel flotation circuits currently experience difficulties in recovering fine particles of pentlandite less than ten microns. By agglomerating these particles using shear-flocculation it is hoped to improve the recovery of these fine particles. A sample of massive sulphide ore from the Kambalda region was separated using magnetic separation to obtain a high grade pentlandite concentrate (> 90 per cent). This was finely ground to produce a sample with particles of 50 per cent minus 10 um in size. This sample was then shear-flocculated using a variety of reagents, including xanthates, dithiophosphate and mercaptobenzothiazole (MBT). The effects of reagent type and concentration, conditioning time, impeller speed and type, and pulp density were studied. Froth flotation tests were also conducted on the shear flocculated pulps to compare the effects of xanthate and MBT on the recovery of pentlandite.

Jan 1, 1992

By Kasaneva S

The San Cristobal gold district is located 110 km east of the port of Antofagasta, Chile. It contains the San Cristobal gold mine, where Niugini Mining Ltd. commenced a heap leach operation, with initial reserves of 10.1 million tonnes grading 1.34 g/t An, in December, 1990. The San Cristobal district occurs within an upper Cretaceous-lower Tertiary magmatic arc. The main mineralisation occurs within a northwest trending subvertical zone, 1km long and 70-100 m wide, which contains rhyolite porphyry and minor breccia, and is locally termed the "subvolcanic complex". At the San Cristobal mine, most gold mineralisation occurs in subvertical quartz-pyrite veins which were emplaced in dilational sections of an imbricate fault system. The bulk gold resource comprises four ore shoots which formed where the vein system intersects the subvolcanic complex. Gold-bearing quartz-pyrite veins also occur at separate prospects, the Three Sisters and Sol prospects, west and south of the San Cristobal mine. Hydrothermal alteration consists of potassic and propylitic assemblages related to intrusion of the subvolcanic complex. This alteration is overprinted by a phyllic stage which is associated with the emplacement of the quartz-pyrite veins. The oxide zone is 180 m thick, and contains native gold, electrum, limonite, and manganocarbonates. The underlying hypogene zone contains pyrite with minor chalcopyrite, sphalerite, galena, covellite, bornite, chalcocite, and arsenopyrite. Fluid inclusion studies indicate that the deposit formed at approximately 270¦ C, and the mean salinity of the fluid was 4% NaCl equivalent. These observations enable the San Cristobal deposit to be classed as a porphyry-related, mesothermal quartz-vein system of the low sulphidation type.

Jan 1, 1995

By Lockhart D. A, Gleeson P, Lang S. C

The Glenrock Group forms the uppermost part of the Early Devonian to Early Carboniferous Burdekin Basin sequence in the Townsville hinterland, north Queensland. As redefined, three formations make up the Glenrock Group. The Percy Creek Volcanics (base), the dominantly epiclastic Mount Douglas Formation, and the Horse Pocket Volcanics (top). The Ellenvale beds unconformably overlie the Mount Douglas Formation and Percy Creek Volcanics and have been excluded from the Glenrock Group as defined by Wyatt and Jell (1980). Three facies associations are recognised in the Mount Douglas Formation: Alluvial Plain facies, Alluvial Fan facies and Lacustrine facies.Deposition of the Glenrock Group, began with the eruption of massive basalt and basaltic andesite lavas, probably in a volcanic arc setting. With time, the volcanism evolved to become more dacitic to rhyolitic in composition. Waning of the volcanic activity appeared to coincide with uplift of source areas (probably to the west). Deposition on an alluvial plain during this waning volcanic cycle, gave way to alluvial fans at the margins of the uplifted terrain. As the uplift ceased and the system became more mature, the alluvial fans gave way to widespread lakes. Rhyolitic ignimbrite and airfall tuff, interbedded with the alluvial plain, alluvial fan and lacustrine facies, indicate that some volcanism continued, probably vented in the uplifted terrain to the west.

Jan 1, 1990

By A Purchase, C Stacey

The procedure for operation of deluge systems installed in road tunnels is still a subject of debate. The work undertaken in this paper assists in the understanding of the effects of deluge in road tunnels, and thus aims to help inform the development of operational policy. Analysis was undertaken using computational fluid dynamics (CFD) simulations to help explore the deluge interaction with the tunnel ventilation (including smoke exhaust) and combustion products. It was found, for the scenarios considered, that: Deluge activation can decrease the required critical velocity for smoke backlayering, and this in turn can improve the effectiveness of a smoke exhaust system.The dominant parameter for deluge effectiveness is the vehicle configuration, with shielded scenarios (such as a fire in the passenger compartment) showing almost no water reaching the fire. The water delivery rate (5 mm/min versus 10 mm/min) has only a minor effect on the smoke duct damper inlet temperatures and downstream smoke temperatures for small fires (5 MW). For large fires (50 MW) the higher water delivery rate gives slightly improved performance (lower damper inlet temperatures and lower downstream smoke temperatures). A one-dimensional transient tunnel model incorporating different operational and deluge response policies (ie deluge activation times) was developed. It was used to examine the influence of different operational parameters on life safety risk and tunnel damage risk. It was found, for the scenarios considered, that: The life safety risk for different scenarios has a sensitivity to deluge activation policy with the case of delaying the deluge activation for a long time giving the worst outcomes. However, the most critical parameters for life safety risk are operator response time (for all response activities, not just deluge) and the type of fire (configuration, size and growth rate).There is a reduction in risk of tunnel damage when the deluge is activated earlier, although the fire configuration (ie whether or not the seat of the fire can be reached) has the greatest influence on the outcome. It is concluded that the deluge activation policy should be case-dependent. It will depend on the tunnel, the safety systems provided, and most particularly the vehicles involved. The current policy in Australian tunnels is for manual activation of the deluge by the tunnel operator as soon as practical after the fire is confirmed (see also PIARC, 2007). This is a good policy. However, future work may be helpful to improve the skills of operators to make the best judgement as to when deluge should be activated, balancing all risks. This work could include research to further the understanding of deluge and fire in road tunnels, training programs and consideration of historical fire events.

Jan 1, 2008

By Zhijing Z, Huiling Z

The influences on flotabilities of dolomite and magnesite with modifiers and influences on the function of collectors and modifiers with Mg+z Ca+2 were studied. The flotation results of artificial mixed mineral showed that using combined salified water glass and (NaPO3)6 as a modifier for magnesite-dolomite separation can obtain an excellent Selectivity.

Jan 1, 1993

Dilution in underground coal operations can be underestimated by up to five times during feasibility studies, with disastrous economic consequences. Every one per cent of stone waste introduced can reduce an in situ specific energy of 25 MJ/kg by some 0.25 MJ/kg and increases the abrasiveness of the run-of-mine coal. Where a wash plant is not in place, penalties imposed for not meeting contractual specifications alone can amount to some $A 1 million per year. This paper presents a method for monitoring, reporting and ultimately controlling dilution in an underground coal mining operation and presents the dilution trends from a continuous miner/longwall mine over an eight year period. The overall dilution level for the mine can be back-calculated by comparing the run-of-mine coal quality to the predicted in situ, undiluted quality. However, this will not identify the actual contaminant types, areas of the mine responsible for the dilution and the reasons for the dilution. This additional information is essential for controlling dilution to acceptable levels. Quality and horizon control using existing sampling information is generally only adequate for longer-term control purposes, and is not suitable for monitoring mining-induced dilution. The cost of close-spaced surface drilling to collect the information necessary for short-term control is prohibitive, particularly for deeper mines. However, much of this data can be collected through underground channel sampling and horizon control measurements taken during continuous miner development and longwall extraction. The mine runs the risk of not meeting contractual quality specifications and of increased equipment wear if this additional information is not available and the sources of dilution cannot be controlled. The information can also be used to plan longwall extraction heights on a short-term scale with resulting improvements in productivity.

Jan 1, 2003

During the past seven years silver recovery has been increased from 9 per cent to over 61 per cent. The changes in plant practiee which have led to this increase are described. Gold room clean-up procedure has been varied, so that half the additional silver is obtained as pure silver chloride, which.is converted to silver bullion for marketing.

Jan 1, 1964

By Champigny N, Grimley P. H

To a bank that granted his request for a loan, the late American humorist Robert Benchley responded, `I don't trust a bank that would lend money to such a poor risk'. This quotation is unlikely to be the norm among mining companies that secure project financing. However, a poor appreciation of one of the key risks of a mining project, the reserves, often results in disastrous financial consequences. This conclusion is the subject of the discussion and analyses presented in this paper.

Jan 1, 1994

Deformation of the lithosphere by tectonic forces is investigated from both observational and theoretical standpoints. Global and regional geophysical data bases, coupled with the means for their rapid display and analysis, facilitate recognition of areas of the con- tinents and oceans where the response of the lithosphere to these deforming processes might fruitfully be studied. Gravity anomalies, from Seasat altimeter data and from land and shipboard measurements, provide critical infor- mation on the isostatic state of deformed lithosphere and therefore on its thermal and mechanical properties.

Jan 1, 1987

In 1975 the US Bureau of Mines (BOM) under contract with the Bureau of Indian Affairs (BIA), began a systematic mineral resource evaluation of Indian reservations in the United States. The purpose of the BIA/BOM program was to stimulate economic development on Indian lands through exploration and mining ventures with the mining industry. Since that time, 109 phase I reports (literature studies) and nearly 45 phase II and phase III (field studies) reports have been written by the BOM. The various tribes in conjunction with the BIA have access to these reports for decision making regarding mineral resource development.

Jan 1, 1990

This paper suggests the models for determination the optimum life of machines on the basis of sum and difference of investment and maintenance costs. The economic-mathematical models are based on complex percentage method taking into account the time factor of referring cost. The following strategies of maintenance policy have been considered in machines repair: a strategy without investment, a strategy with continuous investment and a strategy with step-like investment. The effect of value of investment in repairing and time interval of investment on optimum machine exploitation life has also been considered. An illustrative example is presented.

Jan 1, 2003