Search Documents

By Dai Q

The mechanism of flotation of potash ores with long chain primary amines has been assessed. Since at high electrolyte concentration in saturated brine the electrical double layers of the interacting particles and bubbles are entirely compressed, the induction time measurements confirmed the elimination of kinetic factors associated with the energy barriers opposing particle-to-bubble attachment under such conditions as could be expected. The lack of the kinetic hindrance resulted in the correlation found between the contact angles on the KCl surfaces and the sylvite flotation measured under the same physico-chemical conditions. The iep values and acid numbers obtained for various Esso oils tested as extenders in the flotation of coarse potash ore fractions confirmed the base oils with high content of nitrogen-bearing compounds to be good extender oils. The performance of such oils could further be improved by dissolving in them a small amount of long-chain aliphatic amine.

Jan 1, 1993

There is considerable economic incentive to increase the angle of open pit walls so as to reduce the total volume of waste to be moved to gain access to an orebody. However, a number of slope failures has increased the awareness of mine operators to the potential and consequences of slope failure. Sophisticated methods for the analysis of slope stability have been developed but they rely on an understanding of the appropriate parameters to describe the structural properties of the slope materials. Unfortunately, these properties change with time.The excavation of an open pit mine removes the constraint and weight of the overlying material and allows the newly formed slope to release previously locked in stress. The release of this stress allows the opening of joints and leads to a significant reduction in bulk modulus. The rock mass is also further affected by damage from nearby blasts. Such damage is cumulative and further reduces the modulus of the near surface material and weakens the bonds between structural elements in the slope.

Jan 1, 1992

By Yokozawa K, Yamamoto T, Kameoka Y

Japan Construction Method and Machinery Research Institute has been conducting various field surveys of tunnel works and other excavation works, and the cost and efficiency of these two excavation methods have been studied. Based on these data, the costs of blasting excavation and mechanical excavation represented by roadheaders were calculated. The costs were calculated and compared for rocks of various hardness. When the total construction cost is considered, the degree of overbreak becomes one of the most influencial factors, because the overbreak area must be filled up with expensive shotcrete in NATM. So, in the next step, the relation between the excavation costs considering overbreak and the rock hardness was studied using the data on overbreak obtained by the field survey.

Jan 1, 1987

By Staunton W. P

The presence of cyanide soluble copper in gold ores can give rise to serious operational and economical difficulties in CIP and CIL operations. Cyanide consumption can result in the ore being uneconomic to treat by conventional means. Loading of copper onto carbon can also have deleterious effects on gold recovery and subsequent stripping and bullion recovery. The recovery of gold from high copper ores has been previously reviewed by Muir, LaBrooy and Cao (1989). Work undertaken for Mt Gibson Gold Project by Australian Mining Advisors with the assistance of the Chemistry Centre (WA) resulted in the patenting of a process and subsequent construction of a plant at Mt Gibson to overcome some of the difficulties encountered with copper. This paper discusses some of the work which was undertaken during laboratory investigations prior to commissioning of the plant and some further considerations for the treatment of high copper gold ores.

Jan 1, 1991

The control of industrial grinding circuits in Australian concentrators has been practised for many years in one form or another. Some have established simple feedback loops in areas such as fine ore bin feeders (tonnage control), mill pump sump levels (flow control) and water additions (density control). There are also some sophisticated systems which infer circuit product size using complex measurements of mass flaws and water additions in the circuit and attempts are made to control those flaws to produce a constant circuit product size. The inferred size method in Australian concentrators has become firmly entrenched in the last ten years and control techniques involving the use of direct size measurements with reliable on-stream sizers have been Ignored.

Jan 1, 1983

By C Gypton

This paper gives some insights into what to look for when reviewing feasibility studies. The review by a third party is an important element of the risk management process and may be the last remaining opportunity to uncover errors, or identify and reduce project risks on paper before they are converted to financial disappointments, steel and concrete monuments to process failures or cost overruns. The mining industry has had a spotty record in the area of estimating initial capital costs and operational performance, even though the standard of feasibility studies is generally acknowledged to have improved in the last decades. Third party reviews rarely have the luxury of enough time and unlimited funds, so where should the reviewers focus their efforts to be most effective? Assuming that the project already apparently meets investment criteria, the authors suggest where and how to look among fundamental project parameters for signs that serious flaws exist that have the potential to become project killers. We also give advice on how to review cost estimates without becoming lost in the details. The paper is supported with numerous actual examples.

Jan 1, 2003

By W J. Rankin

A study of refined metallic copper and nickel production was carried out using Life Cycle Assessment methodology to estimate the life cycle emissions of greenhouse and acid rain gases for these metals using data derived from the literature. Various processing routes were investigated which included a pyrometallurgical and a hydrometallurgical route for each metal. The effect of a number of process variables, namely ore grade, fuel type for electricity generation and efficiency of generation were also examined in the study. The results of the study, expressed in terms of total (or full cycle) energy consumption, Global Warming Potential (GWP) and Acidification Potential (AP), showed that the hydrometallurgical processes involving solvent extraction and electrowinning had higher energy consumptions and GWPs than the pyrometallurgical processes for both metals. Nickel metal production was shown to be several-fold more energy intensive than copper metal production. The significant effect that falling ore grades have on attempts to meet greenhouse emission targets was also highlighted in the study.

Jan 1, 2000

By Johnson RD

The variation in coal properties and the coal seam reduced level can be analysed using partial trend-surface analysis techniques. For the area studied seam reduced level and seam thickness data from the Bulli Coal yield trend-surfaces with a high coefficient of determination, since they have relatively small systematic local and random components in their overall variation. Sulphur content appears to have no significant re.gi_onal trend, and phosphorus content has a very weak regional trend. Other analytical variables have regional trends which are of intermediate strength. The strike-directions of.the statistically significant first degree! trend-surface are similar, sug-gesting.: that the variation of the several coal properties was controlled by a set of- related causes. The relations apparent from the dip and strike of the first degree trend-surfaces are similar to- those which are apparent from the trend- surface residuals and'from the results' of canonical trend-surface analysis.'.. It is probable that differential subsidence controlled the areal

Jan 1, 1975

The evaluation programme and procedures develop- ed for Saindak porphyry copper-gold-silver- molybdenum deposits located in an isolated area in an extremely and region of Baluchistan are described in detail. Due to its isol .ted location, far removed from supply centres, harsh climate, paucity of water and non-availability of even unskilled labour, Saindak presented problems for which no ready made solution exist- ed. It is hoped that this Paper may be of some value to those in the LDCs who may wish to undertake similar ventures.

Jan 1, 1988

By Plyley WF

Kidston Gold Mine is a 3.5 million tonnes per year operation located 280 kilometres west of Townsville, Queensland. Kidston's ore body consists of 44.3 million tonnes graded at 1.79 grams per tonne gold and 2.22 grams per tonne silver. Full production commenced in March, 1985. During the remainder of 1985, Kidston milled 3.77 million tonnes of ore and produced 213,614 ounces of gold.The ore is comprised of granodiorite, polymictic and volcanic breccias. The degree of oxidation of the rock influences the milling capacity and therefore determines the cut-off grade; ore is categorised as oxide, transition and fresh. The milling rates are 15,400, 12,000 and 9,600 tonnes per day for oxide, transition and fresh ore respectively.The ore is treated in a conventional cyanidation/ carbon-in-pulp plant (CIP). The plant consists of a primary crusher, semi-autogenous grinding (SAG) and ball mills, leach circuit and carbon-in-pulp circuit. Carbon stripping and dore smelting are done on site. The major difference between the Kidston plant and other Australian CIP plants is that a cyclone separation and washing circuit rejects half of the dry tonnage as a sand tail prior to CIP treatment. This difference allows the CIP circuit at Ki.dston to be smaller and makes the CIP less sensitive to the grind circuit product size.

Jan 1, 1986

By Northcote GG

There are many underground mines with shaft or decline access with limited production capacity or where the mine may become uneconomical as trucking costs escalate with increasing depth of the decline. In such cases a need may exist for a shaft hoisting system which can be constructed more quickly and more economically than a shaft sunk by conventional methods. Relatively cheap small diameter shafts can be constructed by raise boring. This paper describes a simple hoisting system which has been designed to take advantage of the benefits of raise boring. The system uses twin bored raises with a double drum winder hoisting a skip in each hole. The design concept is based on 1. accepting that the raises cannot be truly straight or vertical, 2. using the raise to guide the conveyance, and 3. minimising operating, maintenance, and capital costs. The hoisting system requires a certain degree of accuracy in the alignment of the twin raises. A survey of raise boring practice showed that the required accuracy could probably be achieved with conventional techniques. However it was thought it would be necessary to survey the pilot hole during drilling and to be able to correct the hole if deviation became

Jan 1, 1978

The Western Australian Mining and Petroleum Research Institute (WAMPRI) was established in 1981 by the Western Australian Government as a funding and co-ordinating Institute to foster research into the mining and petroleum industry within this State. To June 1984, the Institute has sponsored 34 projects with a total notional value of $2.5 million and an actual cash commitment of $1.5 million. Strong support for WAMPRI has come from Industry with 60 companies contributing half the money needed for the research grants.The 34 WAMPRI projects funded so far cover all aspects of the mining and petroleum geosciences.Several WAMPRI projects are concerned with gold including processing technology and the development of exploration models and techniques, they are providing successful results.Although well supported by Industry there is a surprising lack of applications being submitted to the Institute in the area of mining engineering, where it is felt there is much scope for research projects.

Jan 1, 1984

By James D, Dawson N

The alternate mineral dressing tech-niques for the production of ilmenite roaster feed from heavy mineral concentrate and the reasons for the selection of wet high intensity magnetic separation (WHIMS) at Richards Bay Minerals are outlined.Initial flowsheet studies were under-taken using laboratory scale equipment followed by on site pilot testing. Flowsheet development culminated with an extensive test programme conducted at Readings of Lismore in 1975.

Jan 1, 1986

By Mur D. M

Metal ferrites are formed by the high temperature reaction of various metal oxides with hematite and are commonly found in the calcines derived from the sulfation roasting of zinc, copper and nickel sulfide concentrates. The Jarosite Process is designed to treat such zinc ferrites by hot acid dissolution but little information is available on the basic reactivity of various ferrites and the effect of Eh. As part of an overall study of the reactivity of calcine products from copper and nickel sulfide concentrates it has been found that Eh plays an important role in the rate of dissolution of magnetite, hematite and nickel oxide by HC1 and H2SO4. Further studies on the reactivity of pure synthetic copper,zinc,and nickel ferrites also show a dependence on Eh. This paper discusses the relative reactivity of iron oxides and metal ferrites in 1 M HC1 and the results of electrochemical studies using cyclic voltammetry. A mechanism for the dissolution reaction is proposed as well as factors which determine their leaching. It is shown that the rate of leaching of metal ferrites with HC1 is enhanced in the presence of reducing agents such as Cu(I) and Sn(II). By contrast the leaching of NiO is enhanced by oxidising agents such as Cu(II).

Jan 1, 1987

By Ross J. F

A pillar 'is a block of coal left in the first working of a coal seam for the purpose of supporting the superincumbent strata in such a manner that the winning out roadways will be safe to traverse by men and by the coal transport system.PRINCIPLES OF PILLAR EXTRACTION.The size of a pillar is chiefly dependent on the depth of cover, and in a lesser degree on the nature of the coal, or the condition in which the seam has been laid down. In a seam at 1,100ft. depth of cover, and assuming a spec'ific gravity of 2.5 overall for the cover strata, a pressure of 1,200lb. per sq. in. is the loading on the top surface of the coal seam before mining begins.When mining commences, and as the pillars are formed, an increased load is imposed on the coal left in the pillars, according to the percentage of coal extracted in the first working. Thus, if 25% extraction is taken in the first working, the load on the pillars is theoretically increased from 1,200lb. per sq. in. to 1,600lb. per sq. in. over the area mined. If this state of things went on indefinitely it would not be possible wholly to extract a pillar because of the extreme pressure tliat would be thrown on the diminishing portion; but, fortunately, another element, that of time, enters into and assists the process of extraction.If the superimposed strata were of an entirely plastic nature, this time factor could not operate, as the cover weight would settle instantly on the remaining portion of the p'illar and finally overwhelm it. The cover strata above a pillar generally have a certain rigidity which does not allow the superimposed weight to settle instantly on the pillar fraction, and it requires a period of time to elapse before the extra weight is felt by the pillar.The time factor varies widely, and is governed entirely by local conditions; it can only be determined by experience gained on the spot or in close proximity to the area of operations. It is dependent on the strength of the strata and its characteristics under bridging conditions.It is, therefore, logical to assume that the more rapidly a pillar can be extracted the greater will be the safety factor and also the percentage of recovery of coal.Up to the present time, the operation of the extraction of pillars in this country has been, with a few exceptions, a manual one, and before mechanization of Collieries can be fully accomplished, the process will have to be performed mecharrically.

Jan 1, 1947

By Svenson D

Most exploratory drilling in the N.S.W. coal fields has been conducted using convent- ional diamond drill rigs of modern design, us- ually truck or trailer mounted. Conventional diamond drill rigs have also been used exten- sively by the Queensland Department of Mines for coal exploration. However almost all of the exploratory drilling of surface mine coal prospects throughout Queensland has been conducted using rotary rigs typified by the Mayhew 1000 truck mounted unit. The rotary rig has proved capable of both rapid non-core drilling and core drilling with high core recoveries when modern core barrels have been used by experienced drillers. For deep or continuous core drilling, wire-line equipment is now in general use. Both wire-line and conventional coring is effected using stationary split inner tube barrels, for minimum core disturbance, maximum core recovery, ease and accuracy of logging and sub-sectional sampling. Diamond core bits are generally required in N.S.W., with water circu- lation. In Queensland, the generally softer coal measures strata can be successfully cored using tungsten carbide bits and air circulation is the preferred method where possible.

Jan 1, 1977

By G Muller, P Larrondo, M C. Godoy

The categories of Mineral Resources and Ore Reserves that may be used for public reporting in Australasia are defined in the current JORC Code (2004). Most internationally accepted codes emphasise the principles of transparency, materiality and competence in classifying resources. They also provide some guidance in considering the impact of data quality. There is no method recommended in the JORC Code to classify a Mineral Resource into the allowed categories of Measured, Indicated and Inferred for public reporting. A clearly defined procedure is desirable for many reasons, including consistency, repeatability and auditability. The demonstrated use of geological knowledge in the classification method is desirable. In deposits with abundant historical data there can be large variations in data type and quality. Quantification of the error of the estimates may also be considered. Ways to formally incorporate such information into the resource classification process are presented as a first step towards establishing an objective, repeatable methodology that allocates resources into appropriate categories based on defined criteria of accuracy and precision.

Jan 1, 2006

By C McInnes

The key to successful flotation plant design, production planning and mine/mill optimisation is a solid understanding of the resource to be processed. As advocated by the authors of this paper, the main components of geometallurgical modelling of an orebody and its associated flotation plant are: an ore sampling program and subsequent laboratory testing of these samples in order to extract process model parameters; geostatistical distribution throughout the resource model of the process parameters; calibration of the plant via benchmarking (for existing operations); and plant simulation using a system of process models and the distributed metallurgical parameters (from step two) as the data set.It is important that the grinding and flotation models are linked. For example, a laboratory test conducted on a drill core sample, intended to represent a portion of the orebody, is conducted at a specific grind (represented by a P80). However, when that ore is actually processed through the plant it may well be (and in many cases most likely will be) at another P80. Additionally, the flotation plant residence time will often be determined solely by the grinding circuit capacity and feed slurry density. In the case of SAG mill û ball mill circuits, the fluctuations in tonnage and grind are known to be high. The modelling approach described in this paper allows for changes in the measured flotation kinetic parameters in order to reflect the expected grind as determined by the comminution process.

Jan 1, 2005

A numerical model of the spontaneous combustion of coal has been developed and is being used to investigate the nature of self-heating in underground coal mines. Results to date confirm the complexity of the self-heating reaction in coal and illustrate the impact of the factors such as the coal reactivity, mass and airflow through the coal pile. Subtle differences in the chemical, physical and environmental conditions and make a significant difference in the development of a high temperature self-heating or a low temperature benign condition, the subtlety escaping normal underground observations. Additional work is planned to investigate the thresholds for such factors in the development of spontaneous combustion and it the implications for detection by gaseous Products.

Jan 1, 1998

The Queensland Magnesia Project is based on a unique cryptocrystalline nodular magnesite orebody which required an innovative approach to process design in order to economically exploit the characteristics of the ore and produce a marketable range of high quality refractory magnesias for a declining world market. High quality natural refractory magnesia must have an MgO content in excess of 95 per cent with a very strictly controlled content and ratio of residual impurities such as calcium, silica and iron. The natural products compete with magnesias derived by chemical extraction from sea water or brines which exhibit very high purity but often lack other characteristics which are of value to refractory brick makers. Since start up in late-1991 QMAG has achieved a remarkable market penetration for both its deadburned and electrofused products with sales for the 1993/94 financial year representing 92 per cent of deadburned capacity and 138 per cent of original electrofused capacity respectively, all at a time when the world steel industry has been in recession.

Jan 1, 1995