Search Documents

By Lane G

This paper addresses project commissioning, that is, activities that culminate in the transfer of a project from the construction phase to routine plant operation. These activities should be initiated early in the engineering and design phase to ensure that the plant design is operator friendly and that construction is scheduled such that pre-operational testing and hand over to the owner occurs in a timely and cost-effective manner. For the purposes of this paper, commissioning includes all activities related to pre-operational testing, no-load testing, water commissioning, and ore commissioning. That is, all activities from construction completion to practical completion of the prime contract. This process is facilitated in numerous ways dependent on the nature of the project prime contract and the size of the project. For small lump sum projects, the contractor's responsibility may include all phases of commissioning to practical completion, whereas, a managing contractor on a complex multi-contract project may only be required to bring the project to mechanical completion and hand over to the owner for ore commissioning. Irrespective of the responsibilities, commissioning programs require careful planning, effective communication and detailed reporting. Unsuccessful

Jan 1, 1997

By Miller M. J, Bauer J. C

The continuous copper drossing process operated at Port Pine since 1962 has had limited copper removal capacity as determined by a maximum tolerable Cu/S ratio in feed and the level of sulphur in blast furnace bullion. Recent process development has been to overcome these limitations to meet increased copper throughput requirements. A sulphur addition system was developed and installed in August 1987. The system has capacity to increase sulphur input by over 150%, meeting the increased copper capacity requirement and also allowing independence from the upstream process for sulphur supply. Developments in process understanding have been applied within the limitations of the existing furnace design with a 10% increase in the maximum tolerable Cu/S ratio.

Jan 1, 1989

By Mortensen JK, Lang JR

The Canadian Cordillera contains numerous classic porphyry deposits and several unusual subtypes, including the alkaline suite of porphyry Cu-Au deposits and the Tombstone magmatic suite and associated Au¦W deposits. The alkaline suite formed in collisional settings in island arcs whereas the Tombstone suite was emplaced in an active fold and thrust belt in a continental arc. In addtion to different regional settings, these suites differ in the type of underlying basement, metallogeny, and the styles of mineralization. Both magmatic suites were emplaced over short intervals, probably in response to specific tectonic events. In the case of the alkaline suite, the tectonic event promoted magmatic processes suitable for the formation of porphyry Cu-Au deposits. The tectonic environment is less well constrained for the Tombstone suite, but the result was the formation of distinctive porphyry and intrusion-related Au¦W deposits.

Jan 1, 1995

By Viney K. G, Molinia A. B

The Hellyer Pb-Zn-Ag orebody in western Tasmania was discovered in 1983, and mine production at a rate of 250 000 tonnes/yr commenced in 1987. Expansion to 1 million/yr will be completed by early 1989. Exploratory development to gain access to the orebody, to provide a 20 000 tonne bulk sample for pilot plant work and to confirm mining conditions and orebody continuity was undertaken using conventional drill and blast techniques and large diesel trackless equipment. A ventilation shaft was raisebored. Development in this phase totalled 2 815 m and provided a sound basis for rapid expansion of the mine.

Jan 1, 1988

By Hall C. E, Chrisholm J. M

Resource calculations for shear hosted deposits of any type are difficult regardless of which calculation technique is used. One of the main problems is the determination of the geometry of the mineralisation. Once this has been elucidated then the appropriate resource calculation methodology can be employed with a search distance and orientation that is relevant.

Jan 1, 1993

By A G. Pavlides, B L. Weekes

The Sepon Copper Project is located in the Savannakhet Province of Laos PDR and is operated by Lane Xang Minerals Ltd (LXML). An Ausenco - Bateman Engineering joint venture, the Khanong Development Group (KDG) managed engineering, procurement and construction of the project. The plant was fully commissioned in March 2005, two weeks ahead of schedule. The plant is designed to produce 60 000 tpa of cathode copper. The process flow sheet includes a pressure oxidation (POX) circuit that leaches pyrite flotation concentrate to generate ferric ions and sulfuric acid for use in atmospheric leaching of a predominantly chalcocite ore. The process is unique in that the chemistry in the autoclave is forced to produce a basic ferric sulfate precipitate for downstream recovery of ferric iron. This paper describes the design, construction and commissioning of the pressure oxidation circuit. The challenges imposed on construction and commissioning due to the remote location of the site, landlocked status and underdeveloped infrastructure in Laos are highlighted.

Jan 1, 2005

By P Rourke

In this climate of increasing demand for commodities, it is becoming necessary to expand and optimise existing bulk material handling facilities in order to increase capacity to satisfy demand. Production capacity in these facilities is often adversely impacted during the expansion process. A successful and proven strategy to reduce this impact is to bring the additional capacity online in stages coinciding with routine maintenance or other short shutdowns. Compatibility of the automation systems with staged upgrades in capacity is the key to achieving a successful outcome. Since 1994, Hatch has been researching a generic, highly configurable product transport control system that can be reconfigured to cater for plant expansions or modifications without incurring significant risk to production capacity. In 2002, BHP Billiton Iron Ore (BHPB IO) recognised the need for such a generic Route Selection and Sequencing (RSS) system and engaged Hatch to build a generic RSS system as part of the $US351 million BHPB IO Products and Capacity Expansion (PACE) project. In 2004, Hatch successfully deployed such a generic configurable control system at BHPB IO Port Hedland Ore Handling Facility. This generic system is known as the Hatch Product Transport (HPT) System.

Jan 1, 2005

By D M. Aranha, A R. Cabral

Theories on the origin of the Itabira iron formation (itabirite) in Quadrilßtero Ferrffero (QF), as elsewhere in the world, are restricted by the apparent lack of adjoining volcanic units, severe syndeformational metamorphism and deep weathering. Besides the three types of iron formations at QF (siliceous, dolomitic and amphibolitic; Dorr, 1969) we include a fourth type initially described as ocherous, goethitic, limonitic or even yellow iron formation. Considering its high magnetite content, it has been described as yellow magnetite itabirite (Pires, 1979). It was reported as formed by the alteration of the dolomitic itabirite (Dorr, 1969) although the anomalous Al2O3 contents are high for normal weathered itabirite. The yellowish magnetitic itabirite occurs at the bottom of the Itabira Iron formation, along the contact with the Batatal schists, and at the top units of the Itabira, within the Gandarela Formation. Within the magnetitic itabirite at the Tamanduß iron ore mine there are metric zones, concordant to the bedding of pillow-like structures, exhibiting a porous core, surrounded by an intermediate, more granular zone with numerous, minute rounded cavities grading to an external, fine-grained zone with much less minute cavities. In the external portions of some pillows a breadcrust type structure, derived by quenching with the water can be observed. In some other zones, such as the Barreiro hill, an outer, vesicular, whitish yellow, 5 - 10 mm thick, band grades to an aphanitic, isotropic band. The vesicles are slightly flattened against the band surfaces. The existence of fragmental layers showing flowage and fragment alignment, kaolinitic laminas and vesicles filled with kaolinite at Barreiro Hill and Capitpo do Mato Mine represent mesoscopic structures, indicators of a possible volcanic origin. Chemical compositions of the magnetitic itabirite from a wide area in QF revealed a relatively high Al2O3 content, consistent with a volcanic origin.

Jan 1, 2005

By D Thornton, B Smith, S Demey

Mine to Mill (MTM) optimisation, a total systems approach to the reduction of energy and cost in mining and mineral processing operations, is well-established technology. However, successful applications of MTM optimisation have been largely confined to gold, copper and lead/zinc semi autogenous grinding (SAG) operations, where the goals of tweaking the blast design to increase fines and hence throughput through the mill have been relatively easy to meet. The application of MTM optimisation in a more demanding environment, like that of a multi-stage crushing and screening aggregate operation, was conceived as part of a Department of Energy (DOE) initiative in 2004, aiming to reduce the energy consumption in the US aggregates industry. Two quarries operated by the Luck Stone Corporation of Richmond, Virginia, were selected for the demonstration sites. Dealing with ore variability and a requirement to maintain a fixed feed size distribution to the tertiary plant, whilst still aiming to increase yields of saleable products, presented some unique challenges. Despite these variables, the implementation of the MTM approach at Luck StoneÆs aggregate plant in Pittsboro, North Carolina, has led to a tangible improvement in productivity, particularly in the primary and secondary plants. The successful outcome was dependent upon several key factors, including reliable blasting and processing models, careful analysis of the rock conditions and plant configuration, understanding and buy-in from the Luck Stone operations staff, excellent collaboration with Virginia Tech staff and students, and long-term monitoring made possible through comprehensive PLC logging. This paper presents a review of the work conducted at the Pittsboro quarry and highlights the key reasons behind the successful implementation of the MTM approach in a complex plant environment.

Jan 1, 2007

This paper presents results of the experiments carried out in Beth Energy No. 33 Mine for the purpose of alleviating problems associated with cutter roof. Cutter roof problems have delayed the advance of the entry development considerably and maintenance cost of these entries was very high due to the requirement of very extensive and heavy artificial supports. The study includes assessment of the problem, investigation of the geology and lithology of the mines, study of in-situ stresses and corrective measures to combat the problem. Two approaches were selected as the corrective measures: 1) implementing yield pillar concept in order to reduce the effects of in-situ horizontal stresses, 2) designing an effective roof reinforcement system and application procedure. Results of this study revealed that roof strata is weak and in-situ stresses are very high at the problem area which results in development of cutter roof. Implementation of yield pillar concept was found to be ineffective because cutter roof often developed at the entry face concurrent to the development. However, proper design and implementation of roof reinforcement system stabilized the roof and eliminated roof caving during both entry development and retreat of longwall face, despite existence of the cutter roof, at a much lower cost.

Jan 1, 1992

The basic principles of mineral valuation were recognised and propounded at the beginning of this century and have remained virtually unchanged since then. Valuation is seen as a two part process commencing with a technical examination of the mineral property followed by a manipulation of the results of the technical examination in order to determine the monetary value of the project. A thorough and competent technical examination was seen then and remains now as the essential but not sufficient foundation for reliable valuation. All authors stressed the need to maintain the integrity of the data base and to ensure adequate coverage of all relevant aspects. The monetary valuation process through most of the first half of this century was mainly based on the Hoskold two rate method, derived from the formulae for valuing annuities but modified to provide explicitly for recovery of capital. Though the basic principles of valuation have not changed significantly, the means of implementing the components of the technical examination, the styles of deposits being evaluated and the mechanisms of monetary valuation have changed dramatically. Despite all the technological improvements, however, mineral valuations are still as apt to vary from realised performance as at any time in the past. As well, mineral property valuations are now being extended to cover all assets of potential value, including valuation of exploration tenements with or without identified resources. Valuation of exploration tenements will continue to be one of the most difficult and contentious of valuation tasks.

Jan 1, 1994

Quite apart from economic considerations, the following performance parameters must be considered when selecting an explosive for a particular blasting operation. 1. total energy yield/kg, and more particularly, strain energy/kg and bubble energy/kg of charge 2. charge weight/m of blasthole 3. sensitivity of the charge 4. water resistance of the charge The effective division of an explosive's total energy into strain energy (SE) and bubble energy (BE) is explained as is the influence of each energy component on blast results. Because some rocks require a high strain energy for effective breakage, while others are most satisfactorily fragmented by bubble energy, values of SE and BE are more meaningful than those of total energy. Unfortunately, our extensive knowledge of the effects of certain variables on total energy has not yet been completely supplanted by the influence of these variables on SE and BE values. Relative SE/kg and BE/kg values are presented for a range of explosives. The 'charge density of ammonium nitrate/ fuel oil (ANFO)-type explosives is essentially constant throughout the length of the charge; because of their compressibility, slurry

Jan 1, 1974

By Abdalla MH

The deformation resulting from the presence of a tunnel may signifcantly affected, nearby structures and need to be considered during design of both tunnel and structure. The aim of this paper is to study the effect of different factors which may affect the interaction between the tunnel and the str- ucture. These include; the depth of both tunnel and foundation level of the structure ( z and t ), distance between C.L. of tunnel and loads, breadth of the loaded area, Diameter of tunnel and lining of the tunnel. The problem is studied as a two dimensional plane strain model by the boundary element technique. The results of this study indicated that the presence of a cavity/tunnel increases, in general, the vertical displacement on the ground surface and at the foundation level as well as the horizontal and vertical stresses in the cavity/tunnel level. The effect of eccentricity is increasing as e/D decreasing. For pile foundation there is a quite different- influence of the presence of cavity/tunnel in both cases of friction pile and end bearing pile type of foundation.

Jan 1, 1987

The necessity for agreed project outcomes, which are in accordance with client needs, and the subsequent requirement for a unique approach to managing project implementation is discussed. Reasons for appointing a separate project team to manage a project are established. The selection of a project manager, based on the services they can provide and on their characteristics, skills and management style, is discussed. The consequences of selecting the wrong project manager are explored. A broad overview of the requirements for the project team is provided. Criteria for the selection of team members, and the role played by the project manager in this selection, are discussed. The levers that drive `on-time and on-budget' projects are discussed in terms of the project's vision, goals, controls, and incentives.

Jan 1, 1997

By A Tomsett, R Kidd, Z Casley

Bivariate recoverable resource estimation aims at predicting the recovered metal for a secondary variable when a cut-off is applied to a primary variable. The choice of a consistent geostatistical model is advisable to allow a robust estimation from exploration data of the primary and secondary metal recovery functions on a generic selection block (selective mining unit û SMU) within large panels. Ore processing decisions at Lihir Gold LimitedÆs Lihir Gold Mine are based on the gold and sulfur estimates of SMUs from production (grade control) data. The predictive model from exploration data at Lihir is based on the estimation of a recoverable resource for gold by Uniform Conditioning (UC), with an estimate of the sulfur grade being provided by Ordinary Kriging of panels. While univariate UC is adapted to the diffusive nature of the gold mineralisation (Ladolam orebody) at Lihir, the independent estimation of sulfur, through ordinary kriging, fails to capture the potential spatial correlation that exists between gold and sulfur mineralisation. This paper presents a practical implementation of bivariate UC, which better represents in the resource model the spatial correlation between gold and sulfur. Incremental economic gains through improved definition of material categories and scheduling are investigated, and the particular impact on the process of geological interpretation and domaining is emphasised.

Jan 1, 2009

With the recent wider introduction of friction hoists of the Koepe type. for winding from depths of more than 3000 feet it has been found that failure by fatigue is the most common form of rope deterioration. Large numbers of wire breaks occur near the centre of the rope cross-section and it is difficult to detect these with certainty using the preferred d.c. magnetic test. For best results with conventional search coils their dimen- sions should be related to the typical wire break field pattern surrounding the longitudionally magnetised rope. The field of a broken wire was experimentally determined, using a Polish type MD6 Defectograph wire rope testing magnet and a short prepared length of rope with a movable simulated broken wire. The external field distortion perpendicular to the rope was measured by means of a gaussmeter and Hall probe. The advantages of this method are that terrestial magnetism and inherent rope "noise" have no effect on the results.

Jan 1, 1971

By Anderson KG

Multi-seam mining under the western portion of Lake Macquarie NSW commenced in 1982. Up to three seams separated by partings ranging from 10 to 30 metres are mined simultaneously by Newcom Collieries. A feature of these workings is the minimal bedrock cover, which ranges from 130 metres down to only 40 metres. "Surface" subsidence control has an over-riding influence on the design of the workings. Subsidence considerations govern both the selection of the mining method and the dimensioning of the workings. To date, workings have been designed in accordance with the "Wardell Guidelines for Mining Under Tidal Waters". These guidelines are tabulated and evaluated in the light of advances in rock mechanics knowledge and local subsidence data collected since the Guidelines were formulated in 1974. The local and regional stability of shallow workings designed according to the Guidelines is evaluated.

Jan 1, 1986

Cable bolts have been used extensively in the development of the footwall of the Mt Whaleback Mine as a part of the ground improvement program since 1986. High tensile seven wire stress relieved steel strand similar to that used in pre-stressed concrete and grouted in place with sulphate resistant cement have been employed for rock-mass reinforcement.Most of the footwall is developed in Mt McRae Shale which contains a 20 m thick pyritic shale layer 14 m below the ore/waste contact. Due to extensive folding of the footwall rocks, the pyritic shale layer regularly occurs on, or close to the pit slope. Rain water run-off seeping through pyritic shale becomes acidic to the extent where its pH value can be as low as 1.5.

Jan 1, 1992

The process of refurbishment is not a precisely defined one. It is under- stood to mean an upgrading of a plant which is normally performed only once. The application of refurbishment in the field of materials hand- ling equipment poses particular problems because complex plants con- sist of individual components having quite different remaining service lives. For this reason, a systematic, proven procedure is proposed for the refurbishment of large materials handling equipment, designed to ensure economic implementation in accordance with the company goals. Rheinbraun2 has been using materials handling equipment since 1900, the largest units today being bucket-wheel excavators with a daily capacity of 240,000 bank cubic metres of overburden and a service weight of up to 13,500 t (metric tons). Since 1975, more than 50 large-scale refurbish- ment projects have been carried out in the company. In the process, refur- bishment has turned out to be the proven alternative to replacement of large materials handling equipment. Rheinbraun Engineering,3 a Rhein- braun subsidiary, carries out planning, consulting, and supervising work in the implementation of refurbishment projects in Germany and abroad. The most recent example is the refurbishment of Dredger 11 of the State Electricity Commission of Victoria in cooperation with Krupp-Australia, Melbourne.

Jan 1, 1989

Mine planning is difficult. Even for small operations, it involves reasoning with complex variables and the practical difficulties of mining. It is also about predicting and planning the future in an unpredictable physical and economic environment. Yet we rely on a handful of individuals and their spreadsheets to tell us how to do it û planning the business and activities of mining to hopefully produce results that will please stakeholders. Does it work? Not as well as it could. Planning affects everyone in the organisation. Company executives are demanding more reliability and stability in cost and revenue forecasts from their operations. Management want to explore ways of being more cost effective. Miners and contractors want more useful plans and realistic targets. And the planners have to describe the method that will translate business objectives into implementable plans. Even with the use of computer technology a lot of effort is expended to produce plans that are largely qualified by the level of knowledge and experience of individuals. Better use of information and the application of Intelligent Technologies can improve the quality and reliability of mine plans and schedules. By capturing the knowledge within the organisation and speeding up the planning process, Intelligent Technologies allow more options to be considered more rigorously. But it is not just about technology. It is about how technology is implemented and embodied in the way the business is managed for performance. When this happens, the real benefits of better planning start to flow.

Jan 1, 2003