Search Documents

By Payne P, Beirne W, Geldard D, O&apos

Whim Creek Consolidated N.L. has operated openpit mines at Meekatharra since 1980. Mining operations commenced with the Haveluck openpit and the Phar Lap openpit was started in 1 984. Grade control in the Haveluck mine was simple because the orebody showed good continuity along strike and down dip and had an easily recognisable hanging wall contact. Problems were encountered once mining corn menced at Phar Lap because of the complex lithologies, alteration and faulting involved. Simple grade control techniques developed for Haveluck failed and were not solved until an understanding of the ore bodies was achieved.The integration of all geological data into the interpretation of the developmentdrilling results has proved essential to achieve effective grade control atreasonable cost.

Jan 1, 1986

By M Coulthard, J Rivalland, K Dugan

Prior to 2001 Yallourn Mine has pumped approximately 1000 Megalitres of water per annum from aquifers beneath the mine floor in order to control aquifer pressures that were thought to have an influence on mine floor and permanent batter stability. In 2001 one of the deep aquifer pumps was shut down for five months in order to measure the aquifer recoveries. Prior to the shutdown a UDEC model was created in order to predict what level of recovery in the aquifer pressures would be critical to mine stability. The shutdown showed that the aquifer levels recovered and stabilised at levels that did not threaten the stability of the mine. The aquifers recovered to levels below the critical levels identified in the UDEC model.

Jan 1, 2003

By Jaracz K

At the operation of mine winders in deep shafts considerable oscillations of winding ropes may occur due to elasticity of both wind-ing and balance ropes. The amplitudes of longitudinal oscillations may reach + lm at relatively low frequencies, ranging from 0.5 to 2 c/s. These oscillations may be dangereus for the rope and produce several hazards to the winding installation as a whole. They may cause conside-rable instant accelerations on the pulley and dangerous tensions in ro-pe wires. The excessive acceleration may cause the uncontrolled rope slip on the pulley. Several methods of limitation of these accelera-tions were developed, some of them have been already in control system: of electric drive of the winder. The most simple ones are: a/ limita-tion of the rate of change of acceleration and retardation of the win-der /so called "jerk"/ and b/ the proper selection of regulators of the winder control system to get the optimal control. The trouble in solv-ing the problem of rope oscillations is that the dynamic system of the winder is a nonstationaryone owing to changing distance of conveyance from the pulley. Besides, the system is described by the equations with distributed parameters. The brief discussion of the theory and its practical aspects are enclosed as well.

Jan 1, 1985

The Mount Kasi gold deposit in Vanua Levu represents an epithermal, high sulphur, gold-enargite system occurring within a volcanic caldera of Middle to Upper Miocene age. High level breccia pipes flare upward and form flat lying, near surface, mushroom shaped sheets parallel and near to the present land surface. The upper portions of the pipes contain explosion breccias which are capped by sandy siliceous sinter-like beds and are cut by alunite veins. Outlying intercalated scoriasceous lavas and breccia sheets show evidence of subsidence within a shallow basin. Detailed mapping of breccia types, intensity of silicification and the presence of multiple quartz veining and enargite abundance outlined blocks of more consistent gold mineralization within the breccias. This work has provided a model for mineralization which will aid future exploration and ore reserve estimations. A significant eluvial concentration of gold occurs in soils overlying the breccia sheet.

Jan 1, 1987

By M H. Randell, J B. Haines

The Honeymoon Uranium Project comprises the Honeymoon Deposit,Goulds Dam Deposit and Yarramba Prospect in the Southern Lake Fromeregion, South Australia. Both the Yarramba Prospect and HoneymoonDeposit (which includes Honeymoon and East Kalkaroo orebodies) arelocated in the Yarramba Palaeovalley. The Goulds Dam Deposit is about75 km north west of Honeymoon, in the Billeroo Palaeovalley. Exploration for sediment-hosted uranium began in the area in the late1960s, culminating in the discovery of Honeymoon and Goulds Dam inthe early 1970s. In 1982, a 25 L/s demonstration plant was built atHoneymoon to confirm suitability for in situ leaching. The project was put on hold in 1983 due to changes in government policy. Southern Cross Resources Australia Pty Ltd acquired the project in mid 1997. Roll-front deposits form from a migrating geochemical cell, anadvancing reduction-oxidation interface between oxygenateduranium-bearing groundwater and its reduced aquifer host. The source of metal is uranium-anomalous granites, which were eroded fromsurrounding ranges. The weathered granites and resultant sediments are stripped of uranium by oxidised groundwaters, to form solutions carrying uranyl carbonate complexes. The solutions percolate down-slope through permeable sand zones until contacting a reduced environment where uranium precipitates. Uranium mineralisation occurs interstitially between and as thin coatings on sand grains, usually in the form of uraninite or coffinite. The palaeovalleys (previously termed palaeochannels) are incised intounderlying Cambrian/Precambrian basement rocks and filled withsemi-consolidated, largely un-cemented, Tertiary sediments of the Eyre Formation. The late Palaeocene to middle Eocene Eyre Formation is the basal unit of the Tertiary succession in the Callabonna Sub-basin of the Lake Eyre Basin. Further to the north, the Lake Eyre Basin overlies the Jurassic-Cretaceous Eromanga Basin, which comprises much of the Great Australian Basin. Eyre Formation sediments are in turn overlain by the late Tertiary Namba Formation and terrestrial Quaternary units. At Honeymoon, the Eyre Formation includes immature, pyritic,carbonaceous sands and gravels interbedded with lignite andkaolinite-illite-montmorillonite clays. It was deposited by braidedstreams during epeirogenic uplift of the Olary Ranges, accompanied bysubsidence of the Lake Eyre Basin. The Eyre Formation comprises aconsistent stratigraphy of interbedded sand and clay units that arecontinuous over the Honeymoon Deposit but with local variationindicating some hydrological connection between aquifers.In the Honeymoon orebody, uranium occurs within coarse-grained,pyritic sands where the basal sand pinches out between overlyingcarbonaceous clay and the southern palaeovalley slope. Its characteristics are typical of the well-developed, planar limb of a roll-front uranium deposit. Zonal changes related to the reduction-oxidation interfaces across the deposit are readily observable. The orebody extends for nearly 1000 m along the valley margin, is 400 m wide at its maximum and averages about 6 m in thickness. The East Kalkaroo orebody also lies near the southern margin of theYarramba Palaeovalley. It extends discontinuously for approximately 3.5 km and averages 200 m width, with significant uranium present in the Middle as well as the Basal Member. The Billeroo Palaeovalley extends northward for 40 km sub-parallel tothe western side of the Benagerie Ridge, is up to 5 km wide and hasgently dipping banks. Eyre Formation within the palaeovalley isconcealed beneath 90 m of Quaternary and Namba cover, isapproximately 40 m thick, and is sub-divided into three upward-finingunits, which are remarkably similar to the Yarramba Palaeovalleysequence.

Jan 1, 2001

Among the various methods of thick-seam mining already well-tried in practice longwall caving with extraction of a single slice, as thick as possible, abandoning the top and/or the bottom coal, seems to be the most suitable one for the Australian coal mining industry. The production units of the future should be equipped with heavy double-drum shearer-loaders, wide armoured conveyors, (with one or two central chains) and shield support. Material of this type has been developed for seams up to 6 m thick. Output figures of more than 6,000 tROM/d from a single face can be looked upon as a quite realistic expectation. The problems of co-ordinating such large production units with the whole layout of the mine are discussed. The factors to be taken into account in the planning work and for preven- tion of mine fires caused by spon- taneous combustion are dealt with. For economic reasons the highest possible utilization factor of the very expensive equipment must be aimed at. Furthermore, the seams or parts of seams to be extracted should be carefully selected.

Jan 1, 1976

By Heidecker A

Several types of drainage structure providecost-effective environmental controls for water supply to Charters Towers and its mining industry. Drainage groves maintain bank-levee, channel, pool, and spring structures. Failure of drainage structures leads to anoxic fermentation of channel fill releasing residues, such as arsenic, which would otherwise pass harmlesly by fixed on sedimentary particles.Experiments along drainage structures indicate that productive agroforestry could be integrated with expeditious development of groves to cope with environmental change.

Jan 1, 1990

By T Goswami, M Edmondson

Henry Walker Eltin (HWE) are the mining contractors for Gloucester Coal at Stratford mine, which is in an environmentally sensitive area in the Avon Valley, NSW, Australia. Normal blasting at Stratford is done in a æstand upÆ or æbox cutÆ mode to suit the truck and shovel operations. Recently an opportunity of doing a throw blast became available when part of a ramp had to be blasted to accommodate changes to the pit design while not damaging the remainder of the ramp. The objective was to maximise throw into the void in order to minimise excavation costs by reducing the amount of overburden to be moved by the excavation fleet. It was necessary that the best result be achieved while staying within the vibration and airblast limits at a neighbouring property and nearby township. Both objectives were achieved through the application of OricaÆs knowledge of blast design, modelling and i-konTM electronic detonators. The i-kon system was used because of its known benefits in cast blasting and environmental control. The i-kon system provides the blaster with much greater accuracy, control and the flexibility to tailor blast designs. It has been found previously to enhance blast throw and provide cleaner high walls (Brent, 2002). The blast was a success, producing a muckpile with a high degree of looseness and consistent fragmentation, with an average throw to final spoil position of 37.5 per cent. This was achieved without any environmental exceedance. In addition, high speed filming showed that the coal edge had remained largely in place, indicating minimal coal loss. The results exceeded the expectations of HWE Stratford and the overall cost savings to HWE Stratford from this blast were recognised to be substantial. Further throw blasting opportunities at Stratford have been followed using the i-kon system to maximise benefits.

Jan 1, 2003

By Heyes GW, Orrock GI

The fine grained complex orebody at Elura contains galena, silver and sphalerite in a matrix which is mostly pyrite; sulphides account for about 90% of the orebody. A differential flotation circuit is operated to con- centrate lead and silver in the first section and zinc in the second. The metallurgical performance to date indicates the need for improvement. The lead section has been sampled in detail to comprehensively assess its overall performance and to define problems associated with lead and silver flotation. The substantial amount of pyrite in the feed dominated the perfor- mance of each stage of the separation. It was responsible for extensive dilution of all concentrates and, as a consequence, for very large circulating loads. The rougher concentrate contained 68% pyrite some of which was rejected through the three stages of cleaning to 39% in the final concen- trate. However, this was still sufficient to hold the assay of this product below 45% Pb. Size by size behaviour shows that flotation rates of the valuable minerals, as characterised by their rate coefficients, were low through- out the circuit. There was a significant deterioration in these rates between rougher and cleaner I stages which resulted in large circulating loads between these stages. There was practically no recovery of coarse valu- able minerals to the final concentrate. The dilution of the final concen- trate by non-sulphide gangue was not a major problem. If the recovery of the galena and silver in the +38¦m size range could be raised to that of the - 381Lm size range, galena recovery would rise from 78% to 86% and silver recovery would improve from 46% to 59%. The Pb grade of the final concentrate would remain the same.

Jan 1, 1988

Epithermal gold mineralisation was discovered at the Muyup prospect during regional reconnaissance exploration in 1986. Further exploration utilising routine techniques of stream sediment, panconcentrate, rockchip sampling and geological mapping resulted in the discovery of five auriferous vein systems located along northwest-trending fault zones. Scout diamond drilling was conducted on two of the vein systems. Mineralisation is hosted by a poorly exposed, mid-Tertiary volcanic inlier composed of intermediate and minor felsic volcanic rocks intruded by intermediate hypabyssal por- phyries. Gold is wholly contained in narrow steep-dipping hydrothermal breccias and quartz vein stockworks in which chalcedonic silica and fine grained quartz is the predominant gangue with minor adularia, carbonate, and sulphides. Alteration zoning is manifested as intense fracture-controlled silicification mantled by narrow clay-rich envelopes which in tam grade outward and downward into propylitic alteration or unaltered host rocks. Late advanced argillic alteration is superimposed on the vein-related altera- tion assemblages. Alteration assemblages and fluid inclusion data suggest that gold mineralisation occurred in response to episodic hydraulic fractur- ing and boiling of low to moderate temperature, dilute alkali-chloride fluids. The Muyup prospect represents the shallow eroded remnants of an epither- mal gold deposit enriched in Au, Ag, As, Sb and Hg. Low sulphur fugacities reflected by vein and alteration assemblages support an adularia-sericite classification (Heald et al, 1987) for this epithennal gold deposit.

Jan 1, 1991

The St George orebodies are situated within the tectonically disrupted eastern limb of the Boogardie Syncline.Highly disturbed rafts of banded chert formations occur within a sequence of felsic volcanic tuffs. The chert forms the hostrock for the gold mineralization.The gold distribution within the irregular and narrow banded chert formations is erratic and patchy. The average gold content of the two orebodies is between 3 - 4 g/t Au.Economic mining of these relative small, irregular and low grade St. George orebodies can be carried out by using a highly selective mining method.The highly selective mining method uses an excavator as the principle mining tool. Blasting, breaking and loading of the rocks is done in a different way than by using a front-end loader as with the conventional mining method. Simple, and therefore cheaper, blasting breaks the rocks and lifts them up without major displacements.

Jan 1, 1984

By E R. Ramanaidou, M S. Piggott

Transport to and handling of iron ore at Port Hedland, Western Australia, results in the generation of airborne particulates that contribute to the atmospheric dust load, with concerns about potential local environmental impacts (eg mangrove swamps) and possible human health implications. Mineral and chemical characteristics of the Background soil samples were contaminated with particles of iron ore as martite octahedra and grains of micro-platy hematite as detected by scanning electron microscopy (SEM) in the 2.5 - 10 ¦m and 10 - 50 ¦m size fractions. Fossilized wood fragments similar to those observed in Yandicoogina fines ore were also detected in some background soil samples. With a predicted increase in demand of channel iron deposits (CID) ores and the inherently dusty Marra Mamba ores (eg West Angelas, MAC, OB29/30/35, Marandoo), in conjunction with particulate emissions from hot-briquetted iron and direct reduced iron (HBI/DRI) processing plants, there is the potential for additional sources of anthropogenic dust to contribute to background levels. Mineralogical and chemical characterisation of the entire range of particulates that could be produced is necessary for a complete understanding of their potential impact on the local environment.

Jan 1, 2002

By Dickson T. J

Slag cleaning is an important part of the pyrometallurgical operations at the Kalgoorlie Nickel Smelter. It is a complex system with many streams of different phases and composition. Some of these streams are very difficult to control and/or monitor. Through the use of a statistical computer package, called Minitab, key relationships affecting the economical operation of the slag cleaning process have been found. Data for the statistical analysis was collected from all possible variables around the appendage.

Jan 1, 1991

By McBride N

Location The Boddington Gold Mine (BGM) is located approximately 120 km south east of Perth, Western Australia. (Figure 1). Located within the picturesque Darling Ranges, the land was previously used for forestry activities prior to mining commencing in mid-1987. Mineralisation is hosted within deeply weathered felsic and intermediate intrusions and volcanic rocks of the Saddleback Greenstone Belt.

Jan 1, 1995

By Shrivastava P

The iron orebodies of the Pilbara region are formed by supergene enrichment of banded iron formation and rarely do such processes produce orebodies with uniform grade distrib- utions. The orebodies being mined or developed have to be worked to grade/quality constraints imposed by contractual agreement rather than natural characteristics. Hence it is imperative to use a non-biased ore reserve calculation method. The geostatistical study of a typical iron orebody is presented. Emphasised are the geological characteristics of the orebody manifested as a variable grade distribution of iron and impurities; the determination of variogram model; subsequent uses of the model for computation of ore reserves and kriged lock estimates; computation of dispersion variance and conditional simulation of orebody.

Jan 1, 1977

By M Surtees

The Limpopo region in southern Africa is considered to be a favourable target for the discovery of base and precious metal mineral deposits. The integration of gravity, geomagnetic, LANDSAT data and geotectonic history is used to formulate an ore deposit model which can be used in the implementation of mineral exploration programmes. Field work was carried out to test and refine the model.

Jan 1, 1993

By D L. Richardson, B Tiedt, C D. Morgan

Following residentsÆ concerns that the ongoing operations of Collinsville Coal (CCP) mine may be resulting in the release of contaminants, including products of acid mine drainage (AMD), into downstream environments, the Queensland Environmental Protection Agency (QEPA) issued CCP with a Notice to Conduct or Commission an Environmental Evaluation at Three Mile Creek. A key objective of the Environmental Evaluation was to assess the extent and magnitude of impacts to aquatic communities and their habitats. A multidisciplinary investigation examined a suite of physical, chemical and biological indicators to meet this objective. The study also aimed to identify contaminants of concern and the location of potential pollutant sources. Potential indicators of AMD, including elevated dissolved solids concentrations and low pH, were evident within the mine lease. However, significant differences in concentration of these indicators upstream and downstream of the confluence with Three Mile Creek were not observed. Although only proxy indicators of AMD contamination, these results suggest that the extent of impacts downstream is minimal. For the purpose of this study, physio-chemical indicators were selected on the basis of those best likely to provide an understanding of the likelihood of contamination, within the constraints of readily available long-term monitoring data. Ecosystem health indicators were adopted to supplement the existing data set and provide a more æroundedÆ perspective of water quality attributes within the system, generally unattainable by standard physio-chemical assessments. In contrast to AMD products, sediments were considered more likely to have a widespread impact on aquatic ecosystems. Waterways throughout the study region, including those unaffected by mining, have been affected by broad-scale sedimentation and were typically highly turbid. Due to the many diffuse sources of sediment potentially liberated within the catchment, the contribution of the mine compared to other land uses on total sediment loads entering streams is difficult to determine. This is clearly a major management issue for mines throughout the Bowen Basin. Streams of the central Queensland region display enormous variability in water flows and physio-chemical characteristics over a range of spatial and temporal scales. This variability presents major difficulties in distinguishing anthropogenic impacts from natural variability (noise). Despite this variability, impact monitoring by mines in the central Queensland district has tended to focus almost entirely upon physio-chemical indicators. The results of the present study indicate that a multiple indicator approach to environmental assessment is more useful for separating mine related impacts from natural ænoiseÆ and impacts from other land uses. In the absence of such information, by adopting the precautionary principle of Ecologically Sustainable Development (ESD), there is potential for an environmental impact to be incorrectly attributed to mining when other activities in the catchment may be contributing to changes in stream æhealthÆ.

Jan 1, 2003

The four major contracts for the construction of Museum Station are: 1) Installation of Soldier Piles, 2) Structural Contract including the temporary support, 3) Architectural Finishes which include Electrical and Mechanical Services and 4) Supply and Installation of lifts and escalators. Specific areas of interest include the fabrication, installation and removal of temporary support steelwork, the monitoring of ground loading, and the interface between the structure and. the temporary support. The information collated during construction confirmed the design assumptions and criteria. No major changes'were required in the design of the construction methods. The open cut excavation and construction of this major structure in an inner city area was significant by any standard and was successfully completed with minimum disruption to the public and without damage to adjoining or surrounding property.

Jan 1, 1981

By Heape JM

Production from the Cattle Grid orebody commenced in August, 1974. This followed a recent discovery arising from an extensive exploration programme involving stratigraphic drilling, geochemistry and geophysics. Located some 4 km west of the original copper occurrences at Pernatty Lagoon the discovery was found to contain 4.6 million tonnes of ore averaging 2.4% copper. The ore is a "sandstone copper" type localised near the disconformity between two Precambrian (Adelaidean) stratigraphic units, the Pandurra Formation and the Whyalla Sandstone. The mineralisation roughly follows the interface between these units and occurs in fractures, vugs and along bedding planes. The mineralogical character of the ore is somewhat complex consisting of chalcocite and bornite, with associated chalcopyrite, sphalerite, pyrite and other less common sulphides. 1. Senior Geologist, Pacminex Pty. Limited, Sydney, N.S.W. 2. Mine Geologist, for Mt. Gunson Mines, Pacminex Pty. Limited, Mt. Gunson, S.A.

Jan 1, 1975

By Thomas L, Archibald N

The use of oxygen in the Mount Percy cyanidation circuit was investigated, with the aim of improving recovery. Preliminary batch and plant testwork justified a plant trial, and it was demonstrated that the use of oxygen reduced gold leachable from plant tailings by 12 per cent, and was economically viable. Oxygen is now in permanent use. Other benefits of oxygen in leaching were not proven. There were no savings on compressed air costs and no measurable reduction in cyanide consumption, although HCN levels in the atmosphere above the tanks declined. The possibility exists that more efficient use of compressed air for tank aeration could have achieved similar recovery gains.

Jan 1, 1992