Search Documents

This paper aims to provide some' new and original thoughts on tungsten carbide drill-bits and describe practices and performances, some of which are unique and most of which have not previously been described. Many theoretical and descriptive papers and articles on carbide bits have appeared during the last few years, and in the big majority conclusions such as these were made. These results are marked by premature failure of the bits, or The full or economic life of the bit is seldom reached due to the premature failure of the insert. Unfortunately those conclusions are seldom accompanied by the reasons for premature failure. In the few cases where reasons for failure have been advanced, very little, originality has been shown. The reasons usually given are that the failures are due to bad operators, bad workmanship, faulty steel or unsuitable machines, but it has been shown at Mount Isa that the chief reason for poor performnce is bad design.The first question asked will be, "What is wrong with the design of most bits?" and the answer'is, "The size of' the inserts". There may be many other small faults iiI different types of bit but Mount Isa experience indicates that the size of the insert is the most important factor influencing pit life. Under normal conditions it has been found, that there is a minimum size of insert that will give satisfactory performance, and this minimum is 5/16 in width and ? in. depth at the shoulder. A big majority of the bits at presentavailable in Australia do not satisfy these requirements.

Jan 1, 1953

The paper describes the preparation of new rail guides, removing existing rails, and replacing with new rails in a vertical winding shaft.INTRODUCTIONThe general practice in coal winding shafts is the use of two cages, with one or more decks in which men and materials are raised or lowered. Winding speeds vary according to depth, the type of winding gear, and whether winding is done in downcast or upcast shafts. Each cage occupies a position between the centre and side of the shaft, with a clearance depending on the type of guides used. The function of the guides is to keep the cage in position throughout the entire depth of the shaft. There are three types of guides, two of which are in general use.1. Selected wood of about 6 in. square section, fixed to the side of buntons.2. Solid strand steel made up similarly to that of an ordinary wire rope, suspended from the head frame with weights attached to the lower end.3. Standard T-rail sections fixed to end or side buntons. Of the three types, 2 and 3 are in general use. The type used in the particular case, the subject of this paper, is T-rails of the standard section used in railway work.GENERAL DESCRIPTION OF SHAFTDetails of the shaft are as follow: Diameter of shaft: 22 ft. inside lining.Depth of shaft: 900 ft., including sump.Concrete lined throughout.VENTILATIONThe ventilation shaft is used for the upcast, through which all vitiated air passes to the main ventilation fan. Quantity of air passing up the shaft is 400,000 cu. ft. per minute. The air is highly saturated during the summer weather and slightly less...

Jan 1, 1947

Papua New Guinea has a long history of mining, with gold being produced from deposits on islands in the south east of the country over a hundred years ago. Before the Second World War, the mining and dredging of gold made the Wau-Bulolo area a

Jan 1, 1994

Every text book for blasting in Japan says that Hauser's law can be applied for practice. But recently it came true that there was no historical record about him and no actual datum of his own or other's to testify. According to his theory, the funnel ratio N = r/W in crater test is inversely proportional to the rock strength and proportional to the explosive amount: where r is the radius of crater and W is the burden. But experiment showed the opposite result, and revealed new information. Two kinds of experiment, crater test and boulder blasting of mortar, were carried out to investigate the effects of rock properties on blasting. The material used for test 1 and test 2 was a mortar block (60cm)3 cube, 4 vertical faces of which were used for crater test. The results from Test 1 and test 2 were summarized as follows. The funnel ratio ranges between 2.5 to 4.5 in proportion to rock strength and burden. The standard ratio of 1, reported by Hauser, was not observed in any instances. It was also noted that the funnel ratio is independent of the explosive amount. The material used for boulder blasting, test 3, was a mortar block (40cm)3 cube, in the middle of which was located a vertical borehole for the explosive charge. The results of test 3 were as follows. The necessary explosive amount for boulder blasting is in inverse proportion to the mortar strength. Fragmentation and throw are proportional to the mortar strength.

Jan 1, 1990

By D Morris

This presentation discusses a water filtration technology termed Fabric Media that is somewhat novel to the Australian market place and reports several recent mining industry installations. Like many novel household cleaning products, the Fabric Media technology applies the science of active washable micro fibres as the means of capturing contaminant solid particles. The simple Fabric Media water filtration product offers several attractive attributes when compared to the more traditional media bed filtration processes such as sand filters, and barrier filters such as micro membranes. A micro fibre based filtration media enables both superior adsorption for the contaminant and wash ability. Stronger adsorption capture enables a much higher flux and greater solids loading density for the filtration task, meaning that lower cost and smaller footprint equipment is available. For Fabric Media water filters, a textile weave is selected that minimises the flow backpressure for a given particle size separation. Thus for an equivalent filtration performance this provides a much lower operating energy requirement, generally between 50 and 80 per cent less than for a sand filter. A Fabric Media is not abrasive to itself or to the filter tank. The filtration performance remains constant and predictable. The equipment life is much longer and the asset value of the new filtration equipment should maintain throughout the project life. Fibres are extremely mechanically robust and chemically inert. Fabric Media survives repetitive exposure to a rapid mechanical washing event providing high wash efficiency with minimum equipment off-line time for the backwash. Dislodging captured contaminants by a high-speed mechanical agitation enables a minimum off-line time during backwash events. The vigorous backwash destroys adhering flocculant and eliminates the formation of mud balls, which can permanently foul sand filters. The mechanical agitation wash of the Fabric Media water filter ensures complete removal of grease and biofilm, which can adhere and block a membrane surface. In comparison to sand filters and micro filtration membranes, the Fabric Media product is applicable to a significantly wider range of solids concentrations without permanent damage. The technology is very forgiving to excursion in plant control and is therefore considered a very operator-friendly concept.

Jan 1, 2006

By R Billingham

QueenslandÆs new safety legislation for metalliferous and coal mining (Mining and Quarrying Safety and Health Act 1999 and Coal Mining Safety and Health Act 1999, together with the Regulations) came into effect on 16 March 2001. The legislation places clear obligations on mine owners, operators and workers to have a safe place of work and to manage risks to safety and health. It also places obligations on contractors, designers and providers of services. The legislation is non-prescriptive in that it states what outcomes must be achieved and not what must be done. The key issue is that the risk of injury to people must be at an acceptable level. The legislation creates a Mines Inspectorate with powers of inspection and audit of mines, their safety management systems and the management of risks. Auditing of the risk management process is carried out against standard risk management techniques and directives for corrective action may be issued when audits reveal non-compliance or unacceptable levels of risk.

Jan 1, 2002

Conceptually coal reserve assessment is simple but in practice it presents many problems. These arise from the origin and geological history of coal seams and from the diverse nature of the coal itself. The suitability of a coal for a particular use depends upon its type and so sheer quantity of reserves does not guarantee the adequacy of coal reserves for all requirements. Codes have been formulated to counteract the effects of subjectivity in reserve assessment. The code for calculating and reporting coal reserves published by the Standing Committee on Coalfield Geology of New South Wales has wide acceptance but the Committee itself recognises that it has shortcomings. Currently the Committee is engaged on the commendable but difficult endeavour of formulating a code that will meet the needs of scientific rigour and professional and commercial ethics and that will allow the specification of an assessment method without constraining it. It is generally agreed in the coal industry that the assessment of coal reserves can not conveniently be incorporated into codes formulated for other resources.

Jan 1, 1979

New South Wales mining legislation reinforces a systematic approach to safety management. It is now a requirement of all mines in the coal, metalliferous and quarrying sectors in NSW to prepare a Mine Safety Management Plan. The paper briefly outlines work currently being undertaken by the Safety Operations Branch of the NSW Department of Mineral Resources (DMR). The DMR is working proactively with NSW mines in the preparation and implementation of effective Mine Safety Management Plans. There is a growing realisation that a systematic approach to safety management, underpinned by the process of hazard identification, has real potential to improve safety in the workplace. The paper briefly describes the framework used in a current æmines education programÆ and its æduty of careÆ foundation. Particular attention is paid to the role of mining operators in the implementation of Mine Safety Management Plans and their expected behaviour in demonstrating compliance. One challenge is convincing some mining operators that they must adopt new ways of working. Safety Operations officers are often reminded of the need to translate Mine Safety Management Plans into practical safety systems during audits and inspections of mines and through investigations into accidents and incidents. To have a real effect on the mineÆs safety performance, using these systems must be a normal way of going about a dayÆs work for all persons who work at the mine: not a safety manual collecting dust on the mine managerÆs bookshelf. Mine Safety Management Plans are important to mining operators. Not only will positive involvement in the development and use of safety systems ensure they meet their obligations under mining legislation, but it will also help prevent themselves or their workmates being injured or killed.

Jan 1, 2002

By D Craw

Otago Schist and Klondike Schist are two Paleozoic-Mesozoic metamorphic belts on the circum-Pacific margin in which there has been a long history of abundant alluvial gold mining, but only minor hard-rock gold mining.   Modern exploration for hard-rock gold is ongoing in both belts, and the active Macraes mine in Otago (>2 Moz production) highlights the hard-rock potential of the geological setting of these belts. Hard-rock gold mineralisation in both belts formed in the latter stages of schist exhumation, after rocks were subjected to major regional ductile folding and then uplifted through the brittle-ductile transition. The majority of known hard-rock gold-bearing systems in both belts consist of well-defined, but generally discontinuous, vein swarms. Most Otago veins are hosted in steeply dipping post-metamorphic normal faults and fractures. However, the Macraes mine is hosted by a late-metamorphic shear zone, and much ore is sulphide-impregnated auriferous schist. Goldbearing veins in the Klondike schist are hosted primarily in extensional sites associated with post-metamorphic compressional structures. Some disseminated sulphide mineralisation is associated with Klondike veins and this is important as it extends the exploration target for these veins. No foliation-parallel late metamorphic mineralisation has been identified in the Klondike but exposure is relatively poor compared with Otago and both schist belts are highly prospective for deposits of this type.

Jan 1, 2007

The products required by customers today have become far more complex and consequently more demanding to handle. And thereÆs the dilemma. Nowadays, people tend to stick to a trade for just a few years instead of for a lifetime, and this means that the customerÆs employees cannot be expected to get more than general knowledge of how to handle modern mining and construction equipment. To meet this challenge, major steps are being taken by suppliers to make their æmusclesÆ more user-friendly. Also the supplier is assuming a larger share of responsibility for the product including operators training, supply maintenance services and, in many cases, performance guarantees. In other words, the supplier is today supplying a function or an activity rather than just muscles. Some of the new generation drill rigs have been on the market for a few years and reliable experience has been collected and is addressed in this paper. Some of the information is well supported by figures while others are just statements from users of the rigs.

Jan 1, 2005

By B Hooper

Deep cuts in CO2 emissions will be required to stabilise and, in the long term, decrease CO2 concentrations in the atmosphere. Technologies for capturing CO2 from major stationary sources (power stations, industrial plants, etc) and storing that CO2 for long periods of time is one of few near term options for decreasing CO2 emissions. This transition to low carbon intensity energy and possibly the hydrogen economy through renewables and in the long-term technological developments such as artificial photosynthesis.Capture of CO2 from post combustion emissions can be done using a range of technologies though costs are currently high and dependent on the concentration of CO2 in the emissions. Techniques include solvents, pressure swing adsorption and the use of membranes. Options for decreasing capture costs by increasing the concentration of CO2 in the emission stream include the use of oxyfuels (in pulverized fuel types boilers) and by moving to integrated gasification combined cycle (IGCC) operations either simply for power generation or for poly-generation opportunities. Once the CO2 has been captured it can be stored using a variety of methods. Storage in the ocean has been suggested but is considered an unlikely option because of environmental uncertainties and political opposition. Mineral storage is a niche opportunity. The greatest potential lies in geological storage of CO2 and this option is commanding increased attention from the Australian and international community.In Australia, the Cooperative Research Centre for Greenhouse Gas Technologies (CO2CRC) is an important new initiative that will support energy companies and energy intensive industries in meeting challenges posed by greenhouse gas issues and assist them in their efforts to reduce their emissions profile.The progress of geo-sequestration and the challenges in the capture and separation of CO2 in the process industries are discussed.

Jan 1, 2004

By N Fullelove

The Renison Bell Tin Mine on the West Coast of Tasmania has recently installed a new underground ore handling system incorporating underground crushing, conveying and hoisting facilities. Contracts for the sinking of the shaft and the development of the mine were let and managed by the operator, Renison Limited. Hardcastle & Richards was responsible for the design, procurement and construction management of the fixed plant and equipment including civil, structural, mechanical, electrical and instrumentation services. The system demonstrates worldÆs best practice in design and incorporates a state-of-the-art integrated control system allowing the entire system to be controlled by a single operator located in the underground crusher chamber. A rapid construction period was achieved, despite the difficult and constrained underground environment, without affecting the ongoing operations of the mine. The mine, which was established in the mid-1960s, had previously operated by trucking ore to the surface via a decline. Truck haulage distances and costs had increased as the mine became deeper over the years. By the 1990s it had become apparent that, in order to remain economically viable, it was necessary to reduce truck haulage distances and allow the mine to go still deeper to access orebodies such as Rendeep beneath the current workings. The Internal Shaft System achieved this by eliminating approximately 5 km of truck haulage. It allows the production rate to be increased to up to 1 Mtpa compared with a limit of 628 kt per annum by direct truck haulage to surface. The access it provides to the Rendeep ore and other deep orebodies greatly increases the amount of ore which can be economically mined.

Jan 1, 1998

By Ballantyne GH

The Ladolam gold deposit on Lihir Island, in Papua New Guinea, is a large disseminated gold deposit hosted by hydrothermal breccias. The deposit occurs in the cupola zone of a 350,000 year old monzonite stock which is emplaced in the collapsed caldera of a shosho- nitic stratovolcano.

Jan 1, 1987

Shortly after the outbreak of war in September, 1939, it became apparent that considerable quantities of certain metals and alloys which at that time were not being produced in Australia would be required in increasing amounts for the prosecution of the war effort.Australian industry had relied on overseas sources of supply for the relatively small quantities of many special metals which were needed under peacetime conditions. As the war progressed so great became the demand for mooy of these alloys in Great Britain and other allied countries that it was necessary for them to place an embargo on the export of these materials, and thus it soon became evident that if Australia's production of munitions was to expand and develop it would be necessary for her to become independent of overseas sources for many of these essential 'items. The shipping position also became very acute, and this, accentuated the difficulties of obtaining these alloys. Because of the conditions outlined aqove, the manufacture of over thirty different metals and alloys .was undertaken at Newcastle during the past decade. It is with two of these that this paper proposes to deal. They are tungsten powder and ferro-silicon.TUNGSTEN POWDERTungsten is a rare and comparatively new metal. It is used extensively in the production of high speed tool steel, some grades of which contain up to 22% tungsten. Such articles as twist drills, reamers, milling cutters, and lathe tools are made from tool steel, and the demand for these during the war years was greater than ever before. The use of tungsten in the manufacture of high speed steel was first developed in 1914 by the Germans, and when it was discovered that they were using tungsten bearing steel for the production of munitions there began a world-wide search for ores of this rare metal.

Jan 1, 1947

In North-West Nelson the Riwaka Complex, a linear basic intrusive complex, is exposed for approximately 45 kilometres. Some 500 kilometres south, across the Alpine Fault, a linear zone of similar but less well known basic intrusives that may be correlatives of the Riwaka Complex is exposed discontinuously for about 80 kilometres. The Complex was emplaced at several centers along a major tensional fracture zone that developed in upper Carboniferous to Lower Permian time. This fracture zone probably formed in response to the development of a west dipping subduction zone that gave rise to the Permian volcanic arcs in east Nelson and western Southland. The Riwaka Complex contains three rock suites. The Fractionation Suite, characterized by cyclic mineral layering and small scale cumulus banding is the largest and is divided into the Ultramafic, Hornblende and Plagioclase Series, each of which is subdivided into several units. The Cumulus Gabbros represent a restricted but important suite of unusual composition, while the third suite is the late phase Diorite Suite.

Jan 1, 1980

By W J. Bruckard, M J. Vaisey

Ashton Mining Ltd (Ashton) and Lynas Corporation Ltd (Lynas) have established a joint venture partnership to develop and process rare earth oxides (REOÆs) from the Mt Weld deposit in Western Australia. The deposit is located in a deeply weathered volcanic carbonatite structure that contains approximately two million tonnes of rare earth oxides at an average grade of 20 per cent REO. As part of the 1999/2000 feasibility study currently being undertaken by Ashton and Lynas, an extensive laboratory beneficiation test program was undertaken by CSIRO Minerals on diamond drill core samples from the Mt Weld orebody. The aim was to develop a flowsheet, based primarily on flotation that could be confirmed at pilot plant scale. The target concentrate grade was 52 per cent REO with a REO recovery of at least 35 per cent. Two main ore types, nominated as CZ (limonitic siltstone) and LI (nodular limonitic ironstone) were identified for separate laboratory evaluation. The lower grade LI-type ore overlies the higher grade and more extensive CZ-type ore. The majority of the work was conducted on the CZ ore; only limited testing of the LI ore was undertaken. The latter contains a clay component that will present difficulties in processing due to its poor filtering and settling characteristics. Two processing options for treatment of CZ ore were presented for pilot plant consideration. One (Option 1) includes gravity concentration prior to flotation while the other (Option 2) includes finer grinding and four stages of open circuit cleaning. The benefits of each scheme are discussed in detail. Neither has been fully optimised and the definitive flowsheet is most likely to be a hybrid of the two schemes, incorporating the best features of each. Typical metallurgical results from each scheme were final concentrate grades of 49 per cent REO, 10-16 per cent Fe2O3 and 3.2-4.8 per cent CaO. REO recoveries were above 35 per cent in both cases. Features of the processes developed by CSIRO were the inclusion of a gravity concentration stage prior to flotation, a modified flotation reagent scheme, a change in the method of feed preparation, and incorporation of magnetic separation to upgrade final flotation concentrates. Metallurgical results obtained from flotation tests on LI ore were much poorer than those obtained for CZ ore. The best rougher/scavenger result, with the limited amount of testing so far completed, was an REO grade of 32 per cent with a recovery of 28 per cent. Further work is needed to develop a viable processing route for this ore type.

Jan 1, 2000

By J Lane, D J. Barker, B Pei

Queensland Alumina Limited (QAL) is the worldÆs largest producer of smelter grade alumina, located in Gladstone, Queensland, Australia. The plant employs evaporative cooling towers for waste heat rejection. Process water requirements include red mud residue disposal, steam venting to the atmosphere and Calcination feed moisture. Raw (untreated) water consumption in 2001 was 37 700 m3/d or 3.8 m3 per tonne of production. The Gladstone region experienced a water shortage in the period 2001 to 2003, resulting in progressive water restrictions. Industry operated under a ten per cent restriction from April 2002 and in November 2002 a 25 per cent restriction came in force. The maximum restriction level of 50 per cent was anticipated for the middle of 2003. Water restrictions of these magnitudes have the potential to result in significant production limitations, which would have major economic consequences for QALÆs owners, customers, suppliers and employees. Therefore it was imperative that measures be found to mitigate the impact of these restrictions. Furthermore, as one of the largest water users in the Gladstone region, QAL had an obligation to the community to minimise water usage as much as possible. A thorough analysis of water usage on site was conducted, focussing on all water streams leaving the plant. The philosophy used was that by minimising water outputs, the inputs would follow suit. Where possible, preference was given to solutions that provided lasting water savings. This occurs when the value of the water saving justifies the project cost, irrespective of water restrictions. By June 2002 an average water saving of 19 per cent was achieved, almost double the required saving. By end November 2002 further projects had increased the total water saving to 29 per cent, mainly through the re-use of GladstoneÆs municipal treated effluent as wash water. Further measures to reach the target of 50 per cent reduction were investigated. The evaporative cooling system was to be replaced with seawater cooling, using cooling towers to minimise the seawater pumping cost. Another benefit of this concept was the ability to dispose of the cooling tower bleed stream with the existing system for neutralised red mud disposal. This would avoid the need for an additional environmental outfall from the plant. In February 2003 the Gladstone region received over 500 mm of rain, which boosted water reserves to five years supply at forecast usage rates. This led to the lifting of all water restriction. As most of the implemented water savings measures are economically viable in the absence of water restrictions, raw water usage at QAL is still less than 75 per cent of pre-2002 levels.

Jan 1, 2003

By Mine F. J, Woods P. H

Waste waters from mine sites may be screened for all constituents of significance as a first step in establishing water quality criteria for protection of aquatic ecosystems. Inductively-coupled plasma mass spectrometry (ICP-MS) offers the capability to screen water samples and digest solutions for virtually all elements in the periodic table. This technique is therefore able to identify elements whose concentrations are elevated in waste waters and may be rarely present in background surface or ground waters. Such elements may be present in waters at only a few ¦g/L. ICP-MS has sufficient sensitivity to detect sub-¦g/L or even ng/L levels of many elements. Waste waters from most mining activities in the Northern Territory have been examined by ICP-MS. The concentration data provide the basis of a contaminant data base. The data can show specific tracers in the ore or mineral itself, subsequently found in waste water. An example is the presence of rhenium in uranium ore. Such trace elements may be present in soluble or insoluble chemical forms and are more useful as indicators when soluble and exemplifying conservative chemical behaviour. The approach described, based on ICP-MS screening of mine site waste waters, together with general physico-chemical variables, provides the most comprehensive means yet available of selecting variables for monitoring programs and ensures that key elements and/or their chemical species are not excluded from monitoring programs.

Jan 1, 1994

The approvals process for a major cut-back is not a simple exercise when a mine is located alongside the community. Kalgoorlie Consolidated Gold Mines (KCGM) has been through an extensive process of government, JV owner and community consultation to ensure that necessary permitting processes and detailed studies have been completed to allow this six year extension to the open pit mine life to be achieved. With the Kalgoorlie Boulder community being on the doorstep of the mine, it is critical to ensure that the operation runs smoothly and complies to the license conditions to achieve the full value of the Golden Pike cut-back, and leave behind a sustainable legacy for the local community. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Jun 1, 2010

By P Stoker

The need for quality assurance and quality control (QA/QC) in the sampling and assaying of minerals is fundamental to the reliability and confidence of a mineral resource estimate, reserve estimate and possibly profitability of a mine. In spite of this, QA/QC practices in the mining industry are commonly applied poorly, or misunderstood. As New Leaders, we should aim to correct the poor practices and become fully informed on appropriate procedures. This paper uses worked examples that show the usefulness and importance of best practice QA/QC procedures. Fundamentals of reviewing the performance of the laboratory by examining the results of client inserted standard reference material (standards), blank material and duplicate samples are discussed. To do this, three examples from Australian data sets have been used. For each example, simple and efficient plotting techniques are suggested with subsequent evaluations of each plot. The first case study compares the results of internal standards from a laboratory with blind standards (where the expected value is unknown to the laboratory) submitted by the client. It was demonstrated over time that the laboratory was unintentionally analysing the internal standards in a different manner to the remainder of the sample batch. In this example, not understanding the cause of a high negative laboratory bias could have led to poor understanding of the depositÆs grade and in the extreme a proposed mining operation may have reached operational stage with a subeconomic grade. The second case study discusses the quality of blank material submitted by a mining operation to monitor cross-contamination within the laboratory. The blank material contained background levels of the element under investigation. This created uncertainty in the assay results, which could have led to the need for additional assays and drilling programs. Finally, the third case study demonstrates the use of the relative paired differences (RPD) technique to cross-validate the results from duplicates and repeat analyses from two laboratories. The three examples given show either laboratory or operational error. If left undetected, each example could have had serious implications for the mineral resource estimate and ultimately, the mining operation. These examples are not isolated occurrences; poor QA/QC practices are an industry wide problem exacerbated by rapid staff turnover and increased contractor positions on-site. New Leaders must be equipped with a thorough grounding in QA/QC best practices to improve its application and confidence in the results of sample analysis.

Jan 1, 2009