Search Documents

By Manzoori AR

From a detailed combustion testing program and earlier experience with Leigh Creek coal, the Electricity Trust of South Australia (ETSA) gained a wide insight into the use of low rank coal fired boiler plant. This work is fundamental for the selection of boiler design parameters and other details which in turn determine the correct coal deposit selection for future power station development. In addition it gives boiler designers a good indication of the measures required to give reliable plant operation. Extrapolation from experience with existing plant, the designers main source of information, was not considered appropriate because of the lack of experience with similar coals. Brown coal beneficiation is also being assessed by ETSA in an attempt to improve the coal quality by the pretreatment of the raw coal prior to combustion in future coal.fired boilers. ETSA is also involved in the development of circulating fluid bed and gasification processes to determine whether these alternative processes are a more viable method of utilising the South Australian coals than pulverised fuel firing.

Jan 1, 1987

By Fairhurst RM

High pressure abrasive water jets have been shown capable of cutting a wide range of materials including steel, stone, rock and concrete. Acceptable performance can be achieved using relatively low pressures and expendable abrasives. The cutting head can be made small and abrasive feed systems have been developed that allow reliable pumping of slurries over long distances to supply such cutting heads. These features make abrasive water jets ideally suited to automated control in remote areas.Another major advantage of abrasive entraining water jet cutting heads is that they may be operated safely in potentially explosive environments due to their cold cutting ability. Therefore there are many possible applications for such equipment in mining.This paper gives an introduction to the abrasive water jet process and includes results of trials carried out at BHRA on a range of hard materials. Work is also described which investigated the operational safety of abrasive water jets in explosive environ-ments. In a special environmental chamber, cuts were made on steel and sandstone with atmospheres of methane/air and hydrogen/air, without caypsing ignition.

Jan 1, 1985

By Goodheart B

The Australian Mineral Sands Industry has expanded from the initial export of mixed concentrates in the 1930s, through various development stages, to its current position as a leading world producer of individual mineral products and some further processed products. Opportunities for downstream processing of the separated minerals and locating such developments in Western Australia are reviewed, along with the role of the Western Australian Government in assisting resource development projects.

Jan 1, 1986

By Jena P. K

Smaller deposits of high grade chalcopyrite or the concentrates of low grade and complex copper bearing ores, can be subjected to extraction processes other than smelting and converting. Low temperature chlorination and segregation processes are among those mentioned in the literature. In the present work, extraction of copper from a Brazilian chalcopyrite concentrate by slurry chlorination with chlorine gas at room temperature, dry chlorination by chlorine gas in the temperature range of 350 to 450¦C and segregation roasting of the calcined concentrate in the temperature range of 650 to 800¦C have been carried out. The effect of several experimental variables on the extraction of copper has been discussed in all these cases. Under optimum experimental conditions, 100 per cent Cu extraction was possible by either slurry or dry chlorination processes and around 86 per cent Cu by segregation roasting. For all the three cases, possible methods have been suggested to trial the studies on a pilot scale to assess their technoeconomic viability.

Jan 1, 1992

By Mills KW

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the loading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992

By Lunarzewski L, Truong D

Although there are sound principles used in the world recognised methods of gas emission prediction, results based on these methods applied to several Australian longwall extractions have yielded unacceptably high discrepancies. With the development of mining in new seams and at higher rates of extraction, the need has grown for a methodical approach to predicting gas emission levels specifically for local Australian mining conditions. Such an approach is developed from results of recorded emission readings during longwall mining at Appin and Pacific Collieries over the past 6 years.

Jan 1, 1988

The integration of historic exploration geoscientific data with high precision multi-element and isotope geochemistry can provide explorers fundamental information on mineral potentiality, tectonic setting, source signatures, fluid migration, mineralisation environment and the timing of mineralising events. Such knowledge is crucial for ore modelling and target generation, particularly for concealed ore systems in both brown and greenfields. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Bougainville Copper Limited (BCL) ships about 600,000 dry tonnes of copper concentrate per annum to Japan, Germany and Spain, with some spot sales to other countries. Concentrate sales value for 1984 was 335 million US$, representing almost half of PNG exports. Contained metal determination is based on physical and chemical measurements on representative samples. The entire procedure is subject to statistical uncertainties and possible systematic errors; losses as high as several percent of contained copper or gold are common and frequently are regarded as unavoidable. In this context, the function of the chemical laboratory is to identify and eliminate such errors and recommend correct technical procedures for possible inclusion in sales contracts. BCL's marketing management has encouraged this approach and the close buyer versus seller agreement is beneficial for all parties involved. BCL participates in the respective technical committees of the Standards Association of Australia (SAA) and the International Standards Organisation (ISO). Standard methods for sampling and analysis of copper, lead and zinc ores and concentrates are in course of preparation, some being due for publication shortly.

Jan 1, 1986

By Quadrio J. S, MacHunter A. M W

The initial development fl6tation testwork on Mt. Windarra op was completed on composited drill core intersections at the.Australian Mineral Development Laboratory. An exploratory winze provided samples, from the 130 M. level of the Mt. Windarra mine, for pilot plant and bench development tests. A limited test programme was initiated on the South Windarra drill core composites. Detailed mineralogy has been completed on selected samples from both ore deposits.

Jan 1, 1973

By Askew J. E

All facets of current practices of cable dowelling at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited are re- viewed. This includes materials specific- ations, installation practices and design pro- cedures. Cable dowelling for cut and fill stoping, square set timber stoping, longhole open stoping and level reinforcement is considered. Installation is simple and can be mechanised to eliminate heavy lifting. Quality control is essential for optimum performance of the re- inforcement. Design patterns must consider the mining method, reinforcement economics, acceptable stability standards and mine production priorities.

Jan 1, 1977

The mmmg operations carried out by North Broken Hill Limited, necessitate the use of four shafts for the haulage of ore, men, and supplies. These are:-1. Blackwood's Shaft.-British Section, which has 100 feet intervals between levels to the bottom 800 feet level plat;2. Thompson's Shaft.-British Section, which has 100 feet intervals between levels to the bottom 1400 feet level plat;3. No. 1 Shaft.-With intervals between levels:(a) 100 feet to the 800 feet level,(b) 150 feet from 800 feet level to the 1700 feet level;4. No. {2 Shaft.-2770 feet from collar to bottom plat, with intervals between levels: (a) 100 feet to 800 feet level, (b) 150 feet from 800 feet level to the 2600 feet level. (c) 170 feet from 2600 feet level to the 2770 feet level.All shafts have two cage compartments, and the No. 2 Shaft a skip installation in addition.For the control of hoisting operations an electric signalling system is installed on each shaft, and is supplemented by a counterbalanced rope pull ("Knocker line") operating a surface gong. The latter system is shown diagrammatically in Fig. 1.Two sets of electrical equipment are used per shaft. The first, shown in Fig. 2, is that operated by the braceman or...

Jan 1, 1940

By Pandey A. K, Srivastava A, Das A

Drilling and blasting constitute important activity in mining operations and account for around 20% of the total excavation cost. The utilization coefficient of energy for explosions of the fragmentation type is hardly 15 to 2035 and an enhancement in this is possible only through optimization of blast design. Designing a 'blast is a complex planning task, which for optimum results calls for matching the energy level of the explosive, rock properties and bench geometry. Optimum blast design needs a comprehensive study and an objective analysis of the intersecting elements. A cost optimised approach is often adopted with due consideration for all the cost sectors viz., drilling, blasting, loading, hauling dumping, and primary crushing, contributing to the overall miring cost. The present study deals with a performance prediction model which predicts the optimum burden for an explosive system in a given rock type to produce a certain desired fragment size. The model is framed on the inputs : shovel size, drill size, unit cost of drilling, bench dimensions, rock density, bond index, unit cost of explosive, maximum work potential. The model has been extended to compute the drilling and blasting costs for an assumed size of the bench to be blasted per round, so as to arrive at the overall cost optimization from a number of explosive systems. A comparative cost calculation with different explosive systems has been presented for a typical iron ore mine in India.

Jan 1, 1990

By Singh RN, Yuejin LI

The problems experienced with longwall mining machinery motivate the development of an expert system for fault diagnosis. The techniques of knowledge representation, database, knowledge base and inference engine guide the selection of the expert systems and languages -"Turbo Prolog"- as exemplified in the case study of hydraulic support. The aim is to hasten future development of a fault diagnosis system and the design of a system to locate and determine the causes of failure of longwall machinery. The system would use its stored case history and other information to make fault diagnoses and suggest appropriate remedies. Consequently down-time would be reduced and production and profitability should increase.

Jan 1, 1991

The granitoid rocks in Burma can be subdivided into three main belts viz. (1) Eastern Granitoid Belt, (2) W-Sn related, Central Granitoid Belt and (3) Porphyry Cu (Au)-related, Western Granitoid Belt. The W-Sn related, central belt Granitoids were interpreted to have generated during the continent-arc collision and the Porphyry Cu(Au)-related, western grantioid belt was emplaced in a magmatic-volcanic arc above an east-dipping subduction zone. INTRODUCTION Major tectonic domains of Burma Burma region can be subdivided into N-S trending (6) major tectonic domains from west to east (1) Arakan Coastal Strip as ensimatic Foredeep (2) Indo-Burman Ranges as Outer Arc or Fore Arc (3) Western Inner-Burman Tertiary Basin as Inter-Arc Basin (4) Central Volcanic Belt (Central Volcanic Line) as Inner Magmatic-volcanic Arc (5) Eastern Inner-Burman Tertiary Basin as Back-Arc Basin and (6) Shan-Tennasserim Massif as ensialic, Sino-Burman Ranges (Bender, 1983). The Sagaing (transform) Fault and Shan Boundary Fault form as a tectonically significant boundary between Eastern-Burman Basin (Back-Arc Basin) and continental,

Jan 1, 1987

By Sims D. A

This paper primarily describes the application of geology to the different mining methods employed in a large underground mine. The steeply dipping stratiform Silver/Lead/Zinc mineralisation at Mount Isa include up to 28 mineable orebodies. The orebodiea are mined by cut and fill, sublevel benching and sublevel open stoping; the method chosen depending mainly on orebody geomechanics.The sources and methods of data collection, and the interpretation process undertaken, are described. The paper emphasises the different geological input required, by each individual mining method, to provide the necessary production and strata control. This input contributes significantly to the success and efficiency of the operations.

Jan 1, 1990

By P Krauss, S Harpalani

Methane emitted from underground coal mines, along with ventilation air and known as ventilation air methane (VAM), constitutes the largest component of coal mine methane (CMM) emissions. Atmospheric methane, on the other hand, is a potent greenhouse gas with a significant adverse impact on the atmosphere. This has led to the development of various technological alternatives for its use as an energy fuel. Techniques involving oxidation of VAM, usually consisting of very low concentrations of methane, have been validated in the past. Prominent among these technologies are the thermal and catalytic flow reversal reactors, ancillary fuel technologies, lean fuel gas turbines, and concentrators and gasifiers. However, the efficiency of any VAM utilisation technique depends on the amount and concentration of methane in the ventilation exhaust air. Therefore, quantification of VAM emission from a coal mine is the first step towards identifying the most suitable technology for its utilisation for energy production. This paper presents an evaluation of the efficacy of VAM as an energy source. It provides details of a case study aimed at developing a technique to accurately quantify VAM emission from a coal mine. It further discusses the various VAM utilisation techniques available, and presents an economic evaluation of the alternatives. Based on the findings of the study, the most feasible method for VAM utilisation is identified for the mine. The paper summarises the procedure for quantifying VAM emissions and selecting the most suitable utilisation technique.

Jan 1, 2005

By Yoon R-H, Luttrell GH

A theoretical model has been developed to predict the probability of particle collection by air bubbles in a quiescent flotation pulp. The model considers the effects of both hydrodynamic and surface chemistry forces acting during the bubble-particle interaction. Hydrodynamic forces considered include the gravitational, buoyancy, streamline and film thinning resistance forces. The surface chemistry forces considered include the electrostatic, dispersion and hydrophobic forces. The hydrophobic force has been estimated from extended DLVO theory. The model is capable of predicting hydrodynamic and surface chemistry conditions under which bubble-particle adhesion is possible. Validity of the model has been verified experimentally.

Jan 1, 1993

**Add abstract here**

Jun 1, 2010

Studies of the morphology of seamounts within the Hawaiian, Line Islands, Gilbert and Phoenix Seamount groups indicate that the morphology and size distribution of seamounts vary significantly from one seamount group to another. The Line Islands group appears to be the most complicated of all the groups studied thus far. This group is complicated by reactivation of volcanism, which has superimposed volcanics on sedimentary rocks. These seamounts display abundant volcanic features on their summits. Seamounts within the Hawaiian seamount chain display a marked absence of volcanic features due to the . presence of thick carbonate caps. Reef platforms and sealevel benches are very common on these seamounts but are absent from seamounts in most other seamount chains in the central Pacific. Slope angles vary regionally between seamount groups. The minimum slopes are found on Necker Ridge in the central Pacific basin. The maximum slopes are found on ridge-crest seamounts. Roughness increases proportionally with mean slope angle.

Jan 1, 1987

The optimization of management structure systems for coal mines is undertaken with the use of economic and mathematical models of the monitoring, manufacturing, and functional subdivisions of the systems. The main para- meter to be minimized is economic loss result ing from organization faults and this is achieved, in part, by optimum distribution of both technological objects and engineering and technical personnel. Models used are of the "gated" type, parameters for which are derived from analysis of manufacturing processes and from automatic information systems. The use of these models ofmanagement structures is only part of the process of optimization of those structures for coal mining operations.

Jan 1, 1977