Search Documents

By Davey P. T, Tsambourakis G

Mineralogical analysis of supergene sulphide ore recovered from areas close to the underground workings at the abandoned Mutooroo (South Australia) mine shows that the original sulphide minerals have undergone substantial alteration. The cause of this alteration is believed to be contact with the highly saline, acidic mine water. The copper is now present as a sulphide that can best be described as a copper- and iron-delicient chalcopyrite, CuxFeyS2, where in most cases x < y. The values of x and y vary from point-to-point within each grain.Leach tests under a variety of conditions show that dissolution of the copper from the supergene sulphide ore can be readily achieved, particularly when compared with the behaviour of Mt Isa chalcopyrite concentrate. For the supergene sulphide ore, an increase in the acidity and the iron(lll) concentration of the leachant re ults in an increase in the rate of copper dissolution.The results are briefly discussed in terms of the experimental in-situ leaching operation at Mutooroo, South Australia.

Jan 1, 1986

By B Dold

"Mining has still today high potential for improvement in the exploitation efficiency. Especially low-grade ores have very low recoveries. In Cu bioleaching operations from porphyry copper deposits extraction of only five and 15 per cent with maximum of 40 per cent are reached. This means that 60–95 per cent of the resource is not exploited. Consequently, any metal not extracted will end up in the waste material, therefore increasing the risk of environmental pollution. This inefficiency is mainly due to the use of element concentrations for decision-making on the daily basis of a mining operation (eg cut-off ore grade, acid-base accounting – ABA). If, instead, quantitative mineralogical and geochemical data together with information on the bioleaching behaviour of the ore assemblage (the biogeometallurgical approach), is used for decision-making right from the beginning of the exploitation, higher recoveries and less environmental impact can be achieved, ie an increase in sustainability can be reached.CITATION:Dold, D, 2016. The Biogeometallurgical Approach – the Information We Need to Increase the Sustainability of Mining, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 169–172 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By M Rafty, C Lane

Managing water is a key aspect of mining, whether a site is in water surplus or water deficit. Water in tailings storage facilities (TSFs) needs to be managed carefully to maximise the density of the solids, maximise the re-use of available water and to minimise the risk of water overtopping the spillway in the event of heavy rainfall. Developing a water balance models is a standard method for monitoring the major flows of water around a site. However, models created by specialist consultants are often overly complex and are not suited to being used by process plant personnel after they have been handed over to the mine operator. Models typically offer information on water management at the time that they are created, but then ‘sit on the shelf’ and offer no further insight or value for operating mines. Advisian has developed a customised water balance model for a mine in Sub-Saharan Africa, which can be adapted to other locations, to assist in managing water at the site and in particular to predict the current and future water level and volume in the TSF under various rainfall scenarios. The model was developed using Microsoft Excel and requires no specialist skills to operate. Site personnel enter in daily production, water transfer and rainfall data and then view the output dashboards to observe the current water level and volume, decant rates, licensed water abstraction and water supply versus demand. The output dashboards were developed in close consultation with the client to ensure that all of the relevant key performance indicators were included, from the perspectives of all the key stakeholders. This modelling approach focusses on the needs of the people who will actually use the model to actively manage TSFs with the need to involve the model developer as part of ongoing operations eliminated. The simplicity of this approach is now being embraced by other mine sites in Africa and Australia. CITATION:Rafty, M and Lane, C, 2018. Water balance management 101, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 485–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Peres EC

The flotability of monazite, zircon and rutile in the presence of sodium oleate, potassium octyl hydroxamate and a commercial hydroxamate was investigated through microflotation tests in a modified Hallimond tube. Zeta potential determinations in the absence/presence of collectors were performed in a microelectrophoretical cell. The microflotation testwork showed that, in general, the flotability characteristics of all three minerals are very similar. Commercial hydroxamate is, by far, a stronger collector than the pure potassium octyl hydroxamate. Electrokinetic studies indicated that the adsorption of collectors shifts the isoelectric point (IEP) of the minerals towards lower pH values. These collectors also are capable of changing the zeta potential values to more negative figures in the pH region above the isoelectric point. An increase of the conditioning temperature, generally, enhances the floatability of the three minerals. A depressant is required in order that selective flotation is feasible in the system monazite-zircon-ruffle. Sodium metasilicate is an efficient depressant for zircon and rutile and affects only slightly the flotability of Monazite.

Jan 1, 1993

By A Grice

AMC has completed a number of backfill options studies, including several in recent years for large, three-dimensional orebodies involving total extraction by longhole open stoping with backfill. This has led to the development of a thorough review methodology that assists in the selection of the most appropriate backfill system and the most economic mixes to achieve the required performance. A recently developed design tool has simplified the calculation of backfill strengths for various exposure dimensions and automatically determines strengths incrementally over the height of a stope. Using a generic orebody with a plan dimension of 120 m wide by 360 m long, several different stoping layouts have been analysed to determine the effect of stope dimensions and sequencing on backfill strength requirements. This has been done for stope heights from 50 m to 300 m, in 50 m increments. The required strengths have been calculated in slices and summarised for each stope in four equal layers. The average strength requirement for each layout at each stope height has been compared graphically. For all stope heights, a panel stope layout that minimises the proportion of primary stopes results in a lower average strength requirement than grid layouts on a checkerboard pattern. However, for very high stopes, smaller plan dimensions become more economic. The increase in required strength with stope height is non-linear, making taller stopes potentially more attractive. The main cost factor in most backfills is the rate of binder addition, which is closely related to the strength required. By choosing a layout that minimises the backfill strength requirement, significant savings in binder addition rates and overall costs can be achieved. These must, of course, be weighed against other factors to determine the optimum stoping layout and backfill system.

Jan 1, 2000

By E Vargas, A Egana, M Alarcon, X Emery, A Barberan, A Lopez, N Morales, C Friedrich

"As the cost in time and money of data from sensors and small-scale tests has reduced, additional challenges have arisen. Although many mine data sets are not big relative to those in other disciplines, they are complex in other ways, and becoming too large to manage efficiently on personal computers. In order to take advantage of the opportunity offered by increased data, a diverse team from Universidad de Chile and CSIRO Mineral Resources has developed a virtual geometallurgical laboratory to support the computational requirements linking data acquisition with data-driven business decisions. A particular focus to date has been the development of user-guided workflow ensembles to enable comparison between plausible geometallurgical hypotheses.A case study has been undertaken using publicly available data from the Rocklea Dome iron deposit in Western Australia. A hypothetical mining schedule was produced from geochemical and hyperspectral drill core/chips data via the following steps: data preprocessing, exploratory data analysis, geochemical interpolation, block modelling, ultimate open pit design and scheduling. The key outcome of this study was the integration of workflow stages through new plug-in methods or modification of existing software. Outcomes from this study will be described in the paper in terms of geological and metallurgical data quality, analytical software support and ongoing computing infrastructure requirements.CITATION:Lopez, A, Barberan, A, Alarcon, M, Vargas, E, Ortiz, J, Morales, N, Emery, X, Egana, A, McFarlane, A and Friedrich, C, 2016. Progress towards Data-driven Mine Planning via a Virtual Geometallurgical Laboratory, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By M M. Pande, M Ishfaq

The effect of aluminium on nitrogen solubility was investigated by equilibrating melt comprising master alloy of Fe-Al with pure electrolytic iron in a controlled atmosphere (pure argon) at 1873 K. Nitrogen in the samples was measured by sampling technique using inert gas fusion absorptiometry. It was found that nitrogen content decreases steadily with aluminium concentration and gradually, becomes close to 1 ppm for very high aluminium steels. Wagner’s second order interaction parameter formalism has been used to estimate the equilibrium constant and interaction parameters. Scanning electron microscopy (SEM) investigation showed, dual-phase inclusions comprising AlN phase surrounding alumina core. The 3D morphology of inclusions was studied by extracting the sample from the top and the central bottom portion of the solidified ingot. A sparse distribution of nitrogen was found for most of the inclusions which manifested the presence of almost pure alumina inclusions with different morphologies and sizes.

Jun 19, 2024

By D J. Williams, E M. Rykaart

Soil cover systems are routinely used to reduce acid rock drainage (ARD) from mine waste rock dumps and tailings impoundments. A technology for the analysis, design, instrumentation and monitoring of barrier-type (oxygen limiting) and store/release-type covers has rapidly developed and the number of covers under construction has grown extensively during the past ten years. Mine operators are currently investing in this relatively new technology with the expectation that these covers will reduce long-term liability with respect to acid generation, drainage and treatment costs. While the design life for cover systems may extend into hundreds of years, we have less than ten years of construction experience and proven performance. Some cover designs appear to be functioning well; however, the performance of many more is now being called into question. The paper presented herein evaluates the integrity of cover systems from a global perspective. Soil cover systems for the control of ARD are being constructed at mine sites located within high rainfall equatorial regions, deserts ranging from low to high latitude, humid temperate regions, and cold-continental climates. While the technology for analysis and design of soil cover systems is well developed, factors that compromise the performance of cover systems (in addition to the paramount issue of climate) relate to material selection and availability, cost and construction practices. Long-term performance is also strongly affected by physical stability (ie erosion), volume change (ie cracking, desiccation, settlement and freeze/thaw cycling), vegetation, soil evolution and ecological stability. This paper provides a review of the application of soil cover systems for the control of ARD. Cases where cover systems have been constructed with both success and failure are illustrated. General criteria and recommendations for cover selection, design, construction, and maintenance are provided.

Jan 1, 2003

By K Kuganathan, Y Potvin

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: a minimum filling rate of 250 m3/h, a curing time of 28 days, and minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998

By E Thomas, L McCallum, G Dale, J Bennett, K Reardon-Smith, S Raine

Sustainable closure of coal mines in Australia to a safe, stable, non-polluting condition remains one of the industry’s biggest environmental and social challenges. A significant proportion of mines in the Bowen Basin of Queensland have dispersive spoil. Based on an estimated area of 20,000ha and a rehabilitation cost of AUD$100,000 to AUD$150,000/ha, the instantaneous rehabilitation liability for the Bowen Basin alone is estimated at AUD$2 to $3 billion.Dispersive spoils present problems in post-mining rehabilitated landforms due to increased potential for surface and tunnel erosion, compromising the ability to achieve fundamental mine closure objectives of a safe, stable, non-polluting and self-sustaining post-mining landform (Minserve, 2004). Dispersion results in clay particles being mobilised and transported in water, even at low flow velocities (So et al., 1998; Minserve, 2004), and blocking of soil pores, resulting in surface sealing, crusting and reduced permeability (DNR, 1997; Vacher et al., 2004) which, in turn, further increases runoff (Dang et al., 2018).CITATION:Dale, G, Reardon-Smith, K, Thomas, E, Bennett, J, McCallum, L and Raine, S, 2018. A process-based approach to mine rehabilitation decision making using Bayesian modelling and risk-based principles for dispersive spoil rehabilitation, in Proceedings Life-of-Mine 2018, pp 106–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By N Udugampola, d A. Seneviratne, X Ai, B Li

With the evolution of mining technology, wireless mesh networks using low-power, long-range technologies such as LoRa are increasingly utilised in underground mining operations. Efficient deployment of wireless nodes in such mesh networks necessitates understanding radio wave propagation behaviour in underground mines. While existing propagation models either remain theoretical or apply only to basic geometric shapes, we propose a practical approach to analyse radio wave propagation behaviour in underground mines using ray tracing simulations with reconstructed 3D models of targeted environments. Our method validated using a set of corridors as a substitute for underground mine environments, involves constructing a 3D model using SolidWorks from LiDAR scans of the environment and performing wireless transmission simulations using the MATLAB ray tracing toolkit. Our simulation model is also fine-tuned by calibrating the raytracing parameters based on real-world LoRa transmission experiments in the actual environment corresponding to the 3D model. This method offers a practical solution for optimising wireless node placement in underground mines, facilitating efficient network deployment while reducing the need for extensive physical testing of radio wave transmissions.

Sep 1, 2024

By Dalzell R. W

A Conveyor Belt Fire Test Program was initiated in 1985 by the Approval and Certification Center (A&CC), Mine Safety and Health Administration (MSHA), U.S. Department of Labor. The purpose was to evaluate the effect of entry air velocities on the burning properties of mine conveyor belts and assess fire test data from large- and small-scale tests. Belts meeting the fire-resistant standards of MSHA and agencies of other countries were tested in small- and large- scale fire tests.

Jan 1, 1988

By Silitonga M

Generally, the acceptable parameter for predicting the intensity of ground vibration due to a blast is the amount of explo ive u ed and the distance from the explo ion. A eries of closely controlled tests were carried out and it was observed that the degree of confinement or burden of an explosive charge play an important role in the variation of the transmitted magnitude of the shock wave through the ground.The intensity of the shock wave increases with burial depth or with greater confinement of an explosion until a critical depth is reached.Beyond this critical depth, the magnitude of ground vibration remain constant. This is an important finding, which explains the anomalies between the expected level and the monitored ground vibration in a particular situation.

Jan 1, 1984

By P J. Bangerter, J Pan

Optimising for Net Present Value (NPV) with a strategic optimiser such as COMET, Prober-E, Blaser or Minemax has hitherto lacked a dynamic method for analysing the so-called third-order outcomes (such as Carbon emissions) of optimisation within life-of-mine planning. Optimisation, per se, has natural effects on carbon emissions in a life-of-mine plan. Contemporary strategic planning employs a mathematical optimiser to make sense of non-linear data (ie a block model) and produces a best-NPV optimised mining schedule, within a set of constraints. The very act of optimisation influences emissions, and in a dynamic way.

Aug 2, 2023

By Gemuts I, Hudson D. R

Massive sulphide mineralisation at the Miriam prospect, near Coolgardie, Western Australia, is fracture-controlled and associated with disseminated sulphides near the basal contact of an ultramafic lens. The lens is peridotitic in composition with a pyroxenitic zone at its base, and lies within a sequence of altered high-Mg basalts and pillowed tholeiitic basalts. Recrystallisation of the ultramafic rock has resulted in the development of secondary olivine. The average composition of the sulphide fraction of massive ore is Cu = 4.4%, Co = 0.3%, Ni = 23.0%, Fe = 31.8%, S = 40.6%, consisting of the supergene assemblage violarite-pyrite to a depth of 210 m.

Jan 1, 1973

By R T. A MacGillivray, S B. Curtis

Bacteriophage (phage) are viruses that infect bacteria. Protein coatings on the surface of the phage particle can be genetically engineered so that they bind to inorganic molecules. The filamentous phage particle is about 930 nanometres in length and 6.5 nanometres in diameter and consists of a single-stranded molecule of DNA surrounded by five different coat protein molecules denoted P3, P6, P7, P8 and P9. Peptide sequences in the P3 coat protein that bind to sphalerite and chalcopyrite have been identified. The binding is selective; phage with specific P3 peptide sequences bind to minerals but do not bind to silica or to pyrite. Two peptide sequences in the P8 coat protein that bind selectively to chalcopyrite and pyrite have also been identified. The amino acids in the P8 binding sequences are hydrophilic and thus a coating of a mineral particle with phage having these peptide sequences may render the particle hydrophilic. Experiments are underway to confirm this. Phage are relatively easy to grow and are not living organisms requiring an energy source to maintain life. Phage can also tolerate a range of pH and temperatures. Given this, and the ability to indentify phage coat proteins that bind selectively to a variety of inorganic molecules, phage have the potential to be useful tools in mineral processing and waste treatment.

Jan 1, 2008

By G McCullough, B Mutsaers, J Jessop

"*This is an abstract only* Geometallurgical initiatives have demonstrated considerable value to operations that have trialled them. However, it is extremely difficult for these initiatives to become properly embedded into the operations and for that value to be realised on an ongoing basis.This paper will explore some of the historical reasons why this is the case. Some of these reasons include the limited tools available to manage an integrated operation. These, in turn, have resulted from poor communications infrastructure, inadequate sensor capability and the way technical mining software has evolved over the last 30 years.This paper will then investigate how the evolution of technology in recent years can help overcome these constraints and compare progress with similar industries.CITATION:McCullough, G, Mutsaers, B and Jessop, J, 2013. Obstacles to embedding geometallurgy decision-making into operations and how to increase maturity of this critical capability, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 139-140 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By D Johansson, C Yi, U Nyberg

Emulsion explosives are a common industrial explosive and have a non-ideal detonation behaviour. The detonation performance for a given product changes with the charge diameter, ground conditions, con?nement and density. The burning process of an emulsion explosive has been modelled with an ignition and growth model in the LS-DYNA code. The parameters in the burning rate function are calibrated by the detonation velocities and the detonation front curvature radii from emulsion explosive tests. A Perl program was developed for an efficient estimation of the parameters, and the results show that the calibrated parameters can predict both detonation velocities and the detonation front curvatures.CITATION:Yi, C, Nyberg, U and Johansson, D, 2015. Parameter determination of an ignition and growth model from emulsion explosive tests, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 585–590 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By MJ SMITH

For the past 150 years, drilling and blasting has been an integral part of the underground mining industry in Australia. Ever since Busby's Bore was developed using black powder to supply Sydney with water, miners have been drilling holes, filling them with explosives and blasting the rock into a manageable size. The drilling was fairly straight forward but the explosives were always a mysterious commodity. It worked, but how and why? The explosives industry is now working much closer to the mining industry to dispel these mysteries and also to aid the advancement of explosive technology. This paper looks at the results of these advances in the form of explosives, accessories and blasting systems.

Jan 1, 1992

A number of suggestions have been made to improve the design of cells used for electro winning and electro refining of metals. Most of these designs have been aimed at increasing the current density used in order to improve cell capacity, although the purpose of some has been to produce electro deposited metals in a continuous manner. Improvements in the electrolyte flow pattern in conventional cells have resulted in an increase in the rate of mass transport of metal ions to the electrode surface; giving rise to lower concentrat- ion polarization and an improvement in the nature of the product obtained, Other cell designs are based on a moving electrode, usually a rotating disk, and these may include provision for removal of the product in a continuous manner, The maximum current density which can be used in an electro- lytic deposition process is determined by the limiting diffusion current, the physical nature of the, product, the purity of the product required and by the increase in power costs which result from the higher cell voltages, This paper examines the properties of an agitated bed of particles as an electrode system when used for a metal deposition Process,

Jan 1, 1969