Search Documents

The seam gas content at Westcliff Colliery is 12-15m3/tonne of coal.Composition ranges from 99% CH4 to 52% C02 in one area. Desorption rates are proportional to gas contents and CH4 is preferentially desorbed. A crushed zone of reduced permeability advances with the face - at Westcliff ribside crushed zones are 2.5 to 6.5m wide. Poor strata control widens crushed zones. 12 months of pre-drainage allowed 2 heading development and longer pillars to be used in a virgin area instead of 3 or more headings without drainage. Machined coal may lose as much as 1.6m3/tonne being conveyed out of Westcliff Colliery. Experience differs from mine to mine. Permeation is affected by time, strata movements, changing water content, and changing stress. Permeabilities vary from lOmd for Pittsburgh Seam to less than 1 and for the Bulli Seam. All these data and differences await further investigation.

Jan 1, 1982

By Miller J. D

The mechanism of adsorption of gold from alkaline cyanide solutions by carbon has been the subject of much research over the past decade. In this paper, the nature of the gold cyanide adsorption phenomenon is investigated, particularly with respect to carbon substrates and associated surface adsorp- tion sites.

Jan 1, 1991

By Aziz NI, Bridgwood EW, Singh RN

One of the major impacts of using modern mechanised systems of mining is the production of large amounts of extraneous dirt intermixed with the Run of Mine output. The paper out- lines a proposed system of utilizing liquid tailings from coal mines to replace imported cementitious materials used in ground control and various other safety measures. A geotech- nical and cost assessment of the proposed system are also included. The paper concludes that it is possible to utilize processed tailings to cost effectively replace imported packing material for ground control.

Jan 1, 1986

Alcoa of Australia's Western Australian bauxite mining operations in the Darling Ranges, south east of Perth, present major challenges in the control of air blast. The close proximity of rural communities and the face profile make the traditional methods of air blast control difficult. An extensive blast noise monitoring programme has been established. The develop- ment of a computerised blast noise prediction model and the establishment of a radiosonde weather balloon facility have reduced blast induced complaints by a factor of ten. The meteorological factors affecting blast noise transmission are discussed and examples are given of adverse weather condit- ions for the south west region of Western Australia.

Jan 1, 1982

By I R. Souza

At the mining industry, there are several uncertainties that may affect the mobile mining equipment fleet sizing and usage, such as commodity supply and demand, which impacts the mineral price, environmental licenses to allow operations and strategic decisions made by the own mining company. Due to that, it may happen to acquire a mobile mining equipment for a specific site and before it finishes the entire forecasted life cycle, the machine gets idle on that operation and a decision must be made regarding this matter. On large mining companies with several sites, equipment transfer provides a good solution to solve this issue and at the same time it provides operational flexibility and allows to use the equipment until the initially planned working hours. This article presents a method to compare technically and financially whether it’s more feasible to transfer a used equipment or to buy a new one. In other words, we will compare a brand-new machine versus a used one in terms of safety, net present value (NPV) considering both capital expenditures (CAPEX) and operational expenditures (OPEX), technological obsolescence, risks, equipment maintenance reliability and lead times. Although it’s not the main purpose of the paper, it will also be briefly discussed the importance of having a considerable amount of backup equipment to handle low likelihood and high consequence risks that may materialise. This backup equipment portfolio is particularly important to avoid loss of sales and profits in case the production plan changes and it demands further equipment than initially planned to cope with the forecasted production.

Nov 8, 2021

By Madgwick J

A novel method for determining viable cells of the mineral leaching bacterium Thiobacillus ferrooxidans has been developed. The cells were collected on 0.45/Lm cellulose acetate filters, washed with artificial minewater, and incubated in the presence of ferrous ion at pH3 in an atmosphere containing radioactive (14C) carbon dioxide. Colonies of bacterial growth were detected by the image formed on X-ray photographic paper (autoradiography). The method was compared with three conventional techniques and shown to detect three orders of magnitude more cells in cultures of Thiobacillus ferrooxidans in the late exponential phase of growth.

Jan 1, 1987

Stressed steel cables, similar to those used in pre-stressed concrete, have been used for rock mass reinforcement, in civil engineering, for many years. This type of reinforcement has been attempted for open pit wall support, on several occasions, but has never gained wide acceptance as a practical approach because of high cost and complexity of installation in a mining environment. On the other hand, untensioned, fully grouted cable dowels (cable bolts) have gained wide acceptance for ground support in underground mining and it is perhaps surprising that this technique has not been used to a greater degree in open pit mining. The first systematic application of this technique in Australia was at the Mary Kathleen uranium mine in 1976, where it was spectacularly successful in maintaining steep stable walls in a jointed rock mass with unfavourably dipping structures. Cable bolting, and other techniques, are now being used to an increasing degree for wall support in both small and large open pits, for two basic applications: 1. stabilisation of potentially unstable sections of a wall, or 2. to allow steeper walls and reduce waste stripping volumes. In virtually every situation, wall rein- forcement has significant economic as well as technical advantages. The paper describes the development of the techniques, the mechanisms of wall support, the methods used, and discusses several case histories of its application to Australian open pit mines.

Jan 1, 1986

By Pollard D. M

The BHAS copper-lead matte leach process, developed in Port Pirie, South Australia, has been in operation on a commercial scale since 1984. This process is one of many developed in the past decade to recover copper via the hydrometallurgical route. In essence, the process involves a single stage agitative leach of 100% -75um matte in an acid chloride-sulphate lixiviant with gaseous oxygen as oxidant. The leach temperature is controlled at 85¦C to assist with reaction kinetics. After leaching, divalent copper is recovered from solution via a conventional solvent extraction/electrowinning circuit to yield cathode copper for sale The BHAS matte leach process has several unique characteristics cf. other commercial oxidative acid leach processes. These include i) the use of gaseous 02 as oxidant ii) H2SO4 addition as make up acid iii) Relatively low chloride ion addition (30 g/1) For this reason, extensive work was carried out into the optimization of leaching by Meadows (1985). Variables investigated included ò Oxygen flow-rate ò Agitation intensity ò Leach temperature ò Free acidity ò Chloride ion concentration ò Matte particle size The current work was conducted to determine the effect of cooling rate, and hence mineralogy, on the leaching characteristics.

Jan 1, 1989

Fission track thermochronology is a well established method for reconstructing the thermal histories of rocks with particularly important applications in tectonic studies, detecting low-grade thermal events, sedimentary basin analysis and resource exploration. These applications take advantage of the limited stability of fission tracks, especially in apatite, when exposed to the temperatures found in the upper 3-4 km of the crust. Apparent fission track ages in apatites can define an invisible 'stratigraphy' in otherwise homogeneous rock masses that can give valuable information on thermal, tectonic and erosional events. Quantitative modelling of the thermal annealing of tracks in apatite shows that distinctive profiles of apparent fission track age can be related to a number of simple thermal history styles. The main types of profile observed tend to be either an essentially linear decrease of apparent age with increasing depth, which relates to continuous uplift and denudation, or a concave-upwards profile produced by partial annealing in environments of tectonic stability or burial. More complex thermal histories produce compound profiles which are essentially just combinations of these two elements. Track length information allows the apparent age profiles to be interpreted in much greater detail. Examples of the major profile types have now been identified in various geological environments and can be analysed to give information about, for example, uplift and denudation rates, the timing of uplift or low-grade thermal events and maximum palaeotemperatures experienced during burial.

Jan 1, 1990

By F Pothitos, S Hewson

The geological and geotechnical conditions at the Cadia Hill Open Pit are very complex. This complexity coupled with high mining rates has required significant technical input into the design and optimisations of the pit slopes, accesses, cutbacks and scheduling. A multi-discipline team of NML engineers, geologists and external consultants has been conducting comprehensive geological and geotechnical programs in order to achieve an optimum design of the pit slopes. Extensive data collection, analysis and interpretation has led to the formation of working geotechnical models of large structures, rock masses, and back-analysed slope performance charts. The current Cadia Pit Optimisation Project focuses on the risk-and-return principle for pit design and on the integration of geotechnical, hydrogeological, mining engineering and scheduling. The risk management for pit design has also been incorporated into the short term and long-term operation of the pit mining to ensure safety and production.

Jan 1, 2003

By Brockway DJ, Holmes RJ

A natural gamma-ray gauge has been devel- oped for discriminating overburden and inter- seam sediment from low ash coal located on a moving conveyor belt. It is based on the difference in natural radioactivity of the sediment and overburden compared with the low ash coal, which is detected with a highly ef- ficient "Polyscin" NaI(T1) gamma-ray detector located underneath the conveyor. Gauges have been successfully installed on the bucket wheel boom of the two coal dredgers at the Loy Yang Open Cut. They are used to warn dredger operators that they are digging overburden or sediment and that action is required to avoid the sediment or divert it to the waste dump rather than send it to the coal bunkers at the power station.

Jan 1, 1987

By Mandzic E. H

The Dome Mine of Timmins Mining company is located in South Porcupine, N.W. Ontario. The orebody being mined partially lies in the No. 3 shaft pillar. Stability analysis has been carried out to establish the influence of nearby mining on ground movement in the shaft vicinity. Mathematical modelling of shaft displacement has been done for stope layout at depths from 180-210 m and distances of 10-50 m from the shaft. Analysis indicated that ground displacement around the shaft is below 1 mm/m and one third less for cut and fill than in the case of open stope mining. The result of the investigation was later confirmed by cut and fill mining of this orebody.

Jan 1, 1986

Tokyo Metropolitan Government designs the stormwater storage plans in underground, as a measure of flood control in completed urban district and improvement of combined sewarage system. This time, introducing those plans, we report about IKEJIRI and SIN-KOMAZAWA STORAGE TRUNK LINEs design and construction. They are located in Meguro river basin of the Morigasaki drainage area. Both storage trunk lines have capacity to store 15O,000m3 of stormwater. They are in use for countermeasure of flood till Meguro river's strengthening (intensity 50 mm/h) is ended. And after the strengthening, they will be in use for improvement of river water quality, through the storage of combined sewage and first runoff, which, otherwise overflows weirs and flows to river in a rainy day. These storage trunk line's full length is about 5700m. Boring diameter 66140 mm (f = 2672m) and 47800 mm (I = 2866m) of these tunnels are constructed by Mechanical Shield tunnelling method. And boring diameter 3600 mm x 4000 mm (R = 180m) is constructed by NATM tunnelling method. We began works in 1983, and have a mind to complete in 1987.

Jan 1, 1987

By Marshall GA

Structural fatigue damage of haul truck frames is a costly problem associated with the operation of large mine haul trucks. A monitoring programme is described which has been instigated to measure stresses in the frames of haul trucks under actual mine operating conditions. The instrumentation used and methodology employed in the computer analysis of the results is briefly described. The results of the monitoring programmes are reviewed, and the effects of various factors affecting structural fatigue damage of three common types of rear dump truck are considered. Factors discussed include the effects of haul route features (for example shovel, dump and crusher areas); the effect of operations such as turning, braking, loading and dumping; the influence of payload; the effects of malfunctions in suspensions; and the influence of haul route surface quality. It is shown that with respect to payload, while structural fatigue damage is increased with payload, the structural damage per unit of payload does not change significantly for moderate increases in payload above the nominal value. Finally, on the basis of these results, recommendations are made for haul route design and operational practices which will increase the structural fatigue life of haul truck frames.

Jan 1, 1986

By M Skead, H Michael, R Chase, A Davidson

Ashanti Goldfields CompanyÆs (AshantiÆs) most recent development is the Geita Project in the Lake Victoria Goldfield of NW Tanzania. It comprises six distinct gold deposits within two mineralised trends: Nyankanga, Lone Cone, Geita Hill (Geita trend) and Matandani, Kukuluma and Area 3 West (Kukuluma trend). Between 1936 and 1966, the Geita area produced an estimated 5.5 M tonnes of ore from five underground deposits at an average recovered grade of 5.3 g/t. The discovery of Nyankanga was made by Ashanti in 1996 from RAB drilling of a +100 ppb Au anomaly in laterite soil above ferricrete cover. The Kukuluma trend was discovered by SAMAX Resources (taken over by Ashanti in 1998) between 1996 and 1997 from RC drilling of a +80 ppb Au laterite soil anomaly. Oxide facies banded iron formation (BIF) of the Upper Nyanzian System forms prominent topographic ridges and is the dominant host lithology for gold mineralisation. The ridges are flanked by felsic tuff units which lie stratigraphically above. Syn-genetic lamprophyre (vogesite) and post-genetic felsic dykes are also seen in the Geita trend. At Nyankanga a granodiorite-diorite suite has intruded as dykes and sills into BIF from a plug centred on a WNW fault and has produced wallrock alteration assemblages similar to those seen in Cu-porphyry systems (potassic, propylitic, etc) as well as sulphide and gold deposition. However, the main ore-grade mineralisation (as in the rest of the Geita trend) is controlled by low-to-medium angle structures dipping north-west and north with numerous splays in the hanging wall. High-grade shoots at Nyankanga plunge to the west and to the north-west, being lithologically and fault-controlled respectively. At Geita Hill the higher grade shoots are controlled by fold noses in BIF dipping to the north. Free gold occurs within fractures of sulphides. The deposits of Kukuluma and Matandani occur on an ancient (possibly Cretaceous) erosional plateau and are related to two WNW to NW trending shear zones, discordant to the local strike of the BIF sequence. Complete oxidation occurs up to 120 m depth and there is a strong supergene component to the gold distribution. Primary gold mineralisation is divisible into two distinct assemblages: arsenopyriteûpyrrhotiteûmagnetiteûchlorite associated with brecciated cherts and pyrite associated with shaley banded ironstones. Area 3W is most likely the fault-displaced extension of the same mineralised trend and comprises thin, intermittent zones of high-grade gold mineralisation occurring adjacent to a ridge in banded cherts and minor BIF. Current resources (measured, indicated and inferred) for the project are estimated at 89.24 Mt at an average grade of 4.17 g/t (11.97 Moz of contained gold) at a 1.0 g/t cut-off grade. Of this 9.83 Moz is within the Geita trend and 2.14 Moz is within the Kukuluma trend. A resource of 2.74 Moz is from an inferred resource at depth at Nyankanga where the viability of an underground operation is being studied. Proven and probable reserves are 49.77 Mt @ 3.46 g/t (5.54 Moz) based on a $325/oz gold price providing a mine life of ten years at an average production rate of 500 000 oz per year. Reserve estimation was carried out using mineable polygons to select resource blocks based on a series of mining and costs parameters. In addition key cost parameters were tested to provide sensitivities for pit optimisations and pathfinders for negotiations with suppliers and contractors. Construction began in March 1999 and first gold is expected to be poured in the second-quarter 2000.

Jan 1, 2000

The Honourable Tony McGrady, Queensland Minister for Minerals & Energy and our local member; the Deputy Mayor of Mount Isa, Alderman Bob Moore; members and guests of the Australian Institute of Mining and Metallurgy; Ladies and Gentlemen; welcome to the Carpentaria and Mount Isa Region Development Forum.Withoutdoubtwearein an exceptional placeatan extraordinary time. In this region we have a numberofexistinganddeveloping mines, plus several major deposits in pre-feasibility oradvanced definition stage, and we continue to see further vigorous exploration. All this mining industryactivity is occurring against a backdrop of wider political, social and economic change, affectingmostofAustralia. The North West Queensland Branch of the Institute decided that the time was ripe for an open forum where issues involved with developing the region's assets be presented and discussed between members of the industry and also the general public.That then is the aim of this meeting: it is to be a place of learning and discussion about issues relevantto the developmentofthese deposits. To this end feel free to use the microphones in the aisles at question time to direct your questions to the speakers.

Jan 1, 1993

By S Amor, A Beasley

This paper provides an example of how industry can respond to the implementation of new regulatory approaches to mining risk, health and safety by adopting a robust, practical, software-based approach to the management of risk accountabilities in terms of competence, experience and suitability for obligations and responsibilities, as required in Queensland Coal Mining operations due to the introduction of Recognised Standard 22 (‘RS22’; Resources Safety and Health Queensland, 2021). Based on the authors’ experience from working with several Qld mine operations, it offers a snapshot of the experiences, approaches and reservations faced collectively by industry as a result of the introduction of RS22. Several challenges exist within the detail of RS22, leading to varied interpretations, implementation strategies and overall compliance between mine sites. Arguably the single biggest challenge identified has been how to find a balance between compliance and practicality – considering cost, operational interruption, available pathways for delivery of competence, ongoing compliance and value adding to the business operations and people. Software-based solutions are increasingly being relied upon to address the introduction of new regulatory approaches and the significant administrative load placed on mining operation Site Senior Executives (‘SSE’) due to RS22 means this case is no different. This is further complicated given the continuous, ongoing changes with the site management structure witnessed by the authors across each of the mining operations as a result of continuous changes to personnel, the site risk profile and an overall mining industry uncertainty of how to respond to RS22. The stringent reporting/notification requirements under legislation compounds this further. The approach put forward by the authors is a well-considered rationale and approach to the application of training and skilling; and equally how to ‘future proof’ the coordination of site training needs around changes to the Management Structure, the Risk Register, skilling processes and succession planning. A brief investigation of other legislative frameworks concluded this approach would likely meet or exceed expectations of jurisdictions across Australia and overseas, making this a highly flexible approach for establishing a competent Management Structure to provide safe systems of work.

Apr 16, 2024

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill both in MICAF sills and in recovery of major horizontal pillars in the 650 copper orebody, where, during mining, cemented fill has regularly been exposed on unsupported vertical faces up to 90 ft high. In the paper the main considerations are the role and specifications of the fill used but also included is a brief description of fill preparation and placement.Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed, and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. The data collected showed that the fill station can operate within tolerances set on product quality, that laboratory and field strength results are comparable, and that rapidly obtained fillsample properties such as moisture content and void ratio can be related to cement content and strength, and hence used for quality control.Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented involving Portland cemented hydraulic fill and alternative, cheaper additives for cementing hydraulic fill. The most significant alternative to Portland cement is quenched and ground copper reverberatory furnace slag, whIch behaves as a pozzolan, reacting strongly with any available lime to produce cementitious hydrated calcium silicates and allowing Portland cement reductions of at least 50 per cent without strength loss.

Jan 1, 1971

By Tucker G, Clark A, Young M. F, Johnston M

Mount Isa Mines has made a huge commitment to process control in milling. Yet in lead zinc we still failed to achieve a steady operation. Comparisons with manufacturing plants showed the key difference was failure to control plant inputs. Lead

Jan 1, 1998

By Fletcher G

This paper will outline the design process, and the constmction and rehabilitation techniques proposed for the external waste dumps associated with the mining of the Wolfang Basin coal measures.The basin is located to the north of Clermont and immediately west of the Bowen Basin in Central Queensland, Australia. Development of the Clermont Coal Mine is planned for the mid-1990s after adequate sales commitments are obtained to allow the project to proceed.

Jan 1, 1992