Search Documents

The international scientific and engineer-ing community is being challenged to take advantage of the opportunity offered by the U.N. International Decade for Natural Disaster Reduction (IDNDR) program to reduce rapid onset geological hazards along the Pacific Rim. Natural disasters observe no national boundaries; international cooperation offers the best opportunity to reduce the losses these catastrophic events create.

Jan 1, 1990

By T QUINLAN

A resource estimate uses data obtained by sampling an orebody. An example is described in which a random drilling pattern did not provide a representative set of assays, and the estimated resource was significantly less than the mine production. It is believed that a better estimate would have been made if the exploration holes had been drilled on a regular grid.

Jan 1, 1992

By T B. T Nguyen, L Matthews, D O’Dea, T Honeyands, T Harvey

Productivity and fuel consumption of the blast furnace is driven by the quality of the iron ore sinter, which in turn is related to the sinter mineralogy. The sintering conditions including temperature and gas composition have a significant influence on the formation of melt and finally the mineralogy of the sinter. In this work, analogue sinter tablets were produced from iron ore fines in a laboratory furnace with tightly controlled temperature profile and oxygen partial pressure in the gas. The mineralogy of the sinters was analysed using reflected light microscopy. The results showed that increasing thermal enclosed area (area enclosed by heating and cooling curve above a reference temperature) reduces primary hematite and platy silico-ferrite of calcium and aluminium (SFCA) contents. This is attributed to increasing melt formation, leading to greater assimilation of the iron ore particles. Lower magnetite was found for tablets with greater median pore size, which is thought to be due to greater oxidation of magnetite to hematite during cooling in air. It was also found that higher alumina content was found to result in more SFCA formation under the same heating/cooling conditions, whereas tablets with higher goethite had higher assimilation and produced more secondary hematite on cooling. Finally, it is necessary to relate the enclosed area to the temperature at which the melt formation becomes significant which strongly depends on chemical composition of the ore studied.

Nov 8, 2021

By I Mason, M van de Werken, B Zhou, J Hargreaves, W Stasinowsky

A critical step in open cut coal mining is clean removal of the overburden. This is usually achieved by drilling, blasting and digging. A key part of this process being successful is to stop drilling at the correct blast ‘stand-off distance’. The stand-off distance is the distance between the base of the drilled blasthole and the top of the coal horizon to be mined. Having this correct provides a protective cap of rock above the coal horizon so that the blast will fracture all the overburden without damaging the coal horizon or mixing it with the overburden. Drilling beyond the correct stand-off distance causes the blast to continue into the coal horizon, damaging it and mixing it with the overburden, leading to significant losses of coal product. Conversely, drilling short of the correct stand-off distance results in additional work to remove the intact overburden.

Sep 1, 2024

By R Varden

This paper summarises the process taken to simplify 35 ground support standards accounting for the multiple development profiles, dynamic geotechnical environment and the practical safety implications of a large-scale change in the ground control standards. This reduction was required after an incident involving incorrect standards being issued. The subsequent investigation identified that: • Selection of ground support standard for a mining instruction (MI) is not straightforward due to multiple standards, standards not reflecting current reinforcement used and complex geotechnical environment being encountered. Instead, site-specific ground control instructions were being issued. • Ground support standards were hard to follow and confusing, errors were present and not all standards to scale. • Ground support standards being used did not reflect what was being installed, ie bolt type incorrect and mesh orientation different. • No process or tier action response plan (TARP) for operators to follow for ground control standard noncompliance. • No justification for ground support standards being used in the current geotechnical environment. • No process for ground support standard selection and thereby no paper trail to document and assess adequacy of performance. A project was undertaken to reduce and simplify the ground support standards, produce a justification document to support ground support design and develop a process for site practitioners to identify the type of ground support standard required for the mining instruction. The exercise of rationalising the ground support was met with some challenges, including: • Technical aspects to determine the level of demand and the capacity for each ground support scheme. • Training the geotechnical engineers how to determine the level of risk for each area. • Winning over other technical services staff and the underground mining contractor of the new approach and then implementation. One of the major successes was the acceptance by the underground operators who found the system simplified their work and gave them increased confidence in management of seismicity. The rationalised ground support standards have now been successfully in place for over two years.

Mar 29, 2023

By Moxon N. T

The detonation pressure of ANFO can be significantly reduced by the addition of low density materials such as polystyrene, bagasse, swadust or perlite. Laboratory and field test results have shown that homogene- ous mixtures of these low density explosives can be produced in a bowl truck and loaded into a blasthole without segregation. The detonation pressure of the mixture can be altered to be more compatible with the material in which it is being used by varying the quantity of low density additive incorporated into the mixture. Field results have shown that these low density explosives can lead to significant cost savings without com- promising fragmentation or production.

Jan 1, 1989

Batterham and Algie began their paper on: `The role of technology in the minerals industry' (1995) by noting that while: it is often stated that innovation is central to the economic survival of mining and minerals processing in the face of global competition, .. . technology is often far from a core strategy in our industry. This point is correct. Throughout the world, as a broad generalisation, mining companies do not value technology development as a principal means of gaining competitive advantage. It is important to understand why this is the case. Batterham and Algie address this question by making distinctions between innovation, technology and research. They note that while: all successful (mining) companies are good at innovation . . . that innovation can proceed without any research and development and that it is innovation that generates the competitive advantage, not research and development per se. In this paper we accept these arguments. However, our focus is somewhat different. Whereas Batterham and Algie took a mining company's perspective on the technologies of mining and processing, we take a broader view of the opportunities for technology development for company Australia but, in order to focus the argument, we restrict our discussion to the area of mining (rather than processing); we focus particularly on mining systems and mining equipment. We begin by looking at the motivation of companies operating in any industrial sector to invest in research and development. Figure 1 recognises four levels of industrial maturity. For companies in the embryonic and growth stages R&D often is essential to initiating and developing the business. Mining, on the other hand, is a mature industry. In mature industries the conventional roles for R&D are to reduce costs, to extend product differentiation, or to develop new technology with the aim of rejuvenating the business. Next we ask whether these general-industry arguments apply to the mining industry. If they do then the mining industry should value R&D more highly; after all cost reductions and business rejuvenation are goals that are worth achieving. On the other hand if, for whatever reason, these general arguments do not apply to mining then this may lead the mining industry to invest only modestly, or not at all, in R&D. In this event, while this may be a rational decision for the mining industry, it may not be in the best interest of a nation like Australia where revenues from the sale of mineral products represent an important part of the country's economy.

Jan 1, 1997

By R Berry, J Lett, C L. Harraden

"In the past decade, increased processing capacity combined with precision robotics in high resolution spectrometers has resulted in a new generation of high-speed hyperspectral core logging systems. The application of these multisensor automated platforms provides a key advancement in the characterisation of metal resources. The development of this technology has allowed for comprehensive, drill core-based, mine-scale rock mass characterisation studies. Here we propose a new method for the extraction of parameters that seek to more accurately quantify ground conditions, including quantified rock mass rating (RMR) and the Rock Tunnelling Quality (Q) Index. Data inputs include rock quality designation (RQD), number of joint sets, joint roughness, joint alteration and joint spacing. Geologists and geotechnical engineers have historically collected these inputs by manually logging drill core. With automated core scanning technologies, these parameters can be estimated from the acquired image data and used to objectively calculate RMR and Q-index values for oriented core.Corescan is an automated hyperspectral core scanner that uses a 3D laser profiling system to measure the height of the surface of drill core. This technology allows for rapid core analysis to produce detailed fracture and rock condition data. Through an integrated geometallurgical approach, the proposed methodology will test the accuracy of joint measurement using the height profile Corescan data from oriented drill core. This will be combined with joint roughness and alteration mineralogy measured from the hyperspectral images to calculate the RMR and the Q-index continuously downhole. The values obtained can then be compared to the traditional, manual geotechnical log data. If the precision is sufficient, these techniques can then be applied site-wide to automate the collection and modelling of key ground condition classification indices across an entire deposit. Compared to the laborious manual geotechnical logging procedures that currently form the industry standard, utilisation of core laser profile data and high resolution red-green-blue (RGB) images provide an opportunity to collect large volumes of consistent geotechnical data, which can increase the efficiency and accuracy of deposit scale geotechnical models.CITATION:Harraden, C L, Berry, R and Lett, J, 2016. Proposed Methodology for Utilising Automated Core Logging Technology to Extract Geotechnical Index Parameters, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 119–124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

Long-range side-scan sonar and conventional geophysical data for the Peru Trench region (8`S-15¦S latitude) have been analysed. The data show that the Peru Trench is a site of sediment subduction where bending-induced normal fault-ing of the Nazca plate plays a key role. The sediments are continually removed from the trench axis region by their inclusion in normal fault-defined void spaces, such as grabens. In the process of subduction, the sediments are often offscraped, folded arid kneaded temporarily at the base of the shoreward trench slope. The subduction complex comprising such sediments is narrower than 20 km and its volume remains more or less constant due to regular removal of its contents along with the down-going plate. Addi-tionally, morphology of the subducting Nazca plate is responsible for subduction erosion of the South American plate, where the horst blocks cause tectonic erosion by abrasion and the grabens provide a mechanism for removal of the eroded material.

Jan 1, 1990

By C Rizos, A Ng

Land surface deformation can be caused by underground mining activities. The maximum subsidence normally occurs directly above the location of the excavation of the coal seam. In the case where the longwall mining technique is applied, the magnitude and shape of the subsidence bowl are constrained by the longwall structure (pillar). This paper describes the use of satellite radar interferometry for monitoring surface subsidence due to underground mining, as a cost-effective geodetic technique and complementary to conventional ground surveying techniques. This paper uses data acquired by the current generation of SAR satellites û the European ENVISAT and the Japanese ALOS û to monitor ground subsidence in the southern highland coalfield in New South Wales, Australia. An accumulated DInSAR subsidence mine map is produced using six successive ALOS acquisitions. The results are post-analysed with the aid of geographic information systems (GIS) and validated using ground survey data.

Jan 1, 2008

By K L. Silversides

Shales form distinctive peaks in natural gamma downhole logs, which are used to manually identify the location of ore boundaries. These shales form important lithology markers that can potentially be automatically identified using Gaussian processes. This approach is trialled using data from a typical iron ore mine in Western Australia which contains the Marra Mamba sequence of the Hamersley province.The method uses Gaussian processes (GPs) with a single length scale squared exponential covariance function. A library of 8 m sections, where natural gamma measurements were taken at 10 cm intervals down the hole, was used to train the GP model. This library was iteratively improved and was tested using natural gamma logs that were not included in the library. Areas that were misclassified or were not clearly classifi ed were added to the library. The new library was then used to train the model and improve the results. The trials used a double gamma peak from the NS3 and NS4 shales at the boundary between the Newman 1 and Newman 2 ore zonesin the Newman member and the AS1 and AS2 shales at the base of the West Angelas member. The results show that both boundaries can be identifi ed with an accuracy of over 99 per cent. The classification has the highest accuracy on undeformed shales. This method provides a fast, accurate and objective identifi cation of shale and ore boundaries and can potentially replace the current manual detection.

Jul 11, 2011

By M W Kearns

The ERA - Ranger Mine ore processing operation consists of a sulphuric acid leach followed by counter current decantation and solvent extraction circuits. The most expensive unit processing operation at Ranger is the sulphuric acid leach. In 1992 and 1993 changes were made to the operation of the leach circuit. These changes have reduced power and reagent consumption in leach by 30 per cent and 20 per cent respectively with minimal effect on extraction efficiency. The first change was to operate the leach circuits at higher pHs than previously attempted. In addition a cap was placed on the amount of acid added to the leach circuit. Secondly, an on-line pH measurement system was installed and has reduced the variation with time of the leach circuit pHs. Finally, the number of leach vessels used was reduced from ten to seven. This action was undertaken after an examination of the uranium profile and the residence time in the leach circuit from previous years. This paper examines the above changes and assesses their effectiveness on plant performance and costs.

Jan 1, 1994

By P Mitchell, S Pushpan, G Ferres, K Bobbermien, L Hudson

"Falling commodity prices and a rising supply surplus have ushered in a period of restraint in capital project investment across the global mining and metals sector. Competition for capital project funding has seen fewer projects progress through investment gates and a stronger focus on projects that deliver gains in capital productivity and strategic outcomes.Over the course of the 2015 financial year, EY conducted a study of 108 projects in the global mining and metals sector (EY analysis; Larsson and Ericsson, 2014; SNL Financial, 2015). The projects studied were at various life cycle stages and related to the development of copper, iron ore, gold, coal, nickel and other commodities. Each individual project investment exceeded US$1 B, and the studied group represented a cumulative investment value of US$367 B.The research found that the majority of projects were delayed and/or over budget when measured against the initial estimates made during the early stages of the project life cycle. Of the surveyed projects, 69 per cent were identified as facing cost overruns with an average overrun of 62 per cent above the initial estimate and 50 per cent reported schedule delays, even after remedial acceleration initiatives.The analysis found that budget and schedule overruns could be attributed to five key causes:project management factorsstakeholder conflictsresource constraintsregulatory, and policy-related challengesunfavourable external environment.Improving project delivery performance starts with successful planning, followed by rigorous management during delivery. From global experience on large and complex capital programs, EY has observed a consistent theme of underinvestment and a lack of focus in three often-overlooked but critical areas:implementing effective governance and reporting frameworks with lead indicators that reliably flag emerging risks while they can still be mitigatedallocating adequate cost and time contingency to account for risks across the life cycleenhancing the value of contingency by aligning contingency plans with scenario plans.This paper explores the surprising findings of the study, proposes a root cause model and examines key considerations in applying these critical enabling techniques.CITATION:Hudson, L, Mitchell, P, Ferres, G, Bobbermien, K and Pushpan, S, 2016. Are your megaproject schedules and costs under – or out of – control?, in Proceedings Project Evaluation 2016, pp 75–85 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By P F. Knights, P Boniwell

This paper investigates the causes of low effective utilisation of the production drill fleet at the Telfer Underground Gold Mine, as measured by the percussion hours per shift. The first part of this paper focuses on a site time and motion study conducted to accurately identify shift time allocation and optimal drilling parameters (manual versus automatic, and suitable flushing mediums for varying ground conditions) as well as quantifying the business potential for automated or remotely operated production drilling. The second part of the paper focuses on the rate of successful hole completion for automated production drilling during shift changes. Two main areas of drill optimisation were identified. Firstly, a site-specific drilling procedure was established so as to ensure that all operators were drilling using optimal parameters. Total production metres per rig increased by 10.7 per cent as a result of the implementation of this standard. It was observed that a 25 per cent faster overall drill cycle was achieved using air mist flushing, and that manual drilling achieves a 19 per cent faster overall drilling cycle in comparison to automated drilling. Secondly, routine provision to the maintenance department of automation reliability reports that outlined the principal causes of unsuccessful hole completion led to an increase in production metres of a further 4.1 per cent, measured between January 2007 and August 2007. First hole automation reliability increased from 39 per cent to over 77 per cent over the same time period. Second hole automation completion was increased to 74 per cent, leading to a higher proportion of production achieved through automated technologies.

Jan 1, 2008

By D Xiong, G Xu, L Yao, F Wang, Y Duan

The goal of this project has been to digitise and use drill parameter data from rotary drilling (measurement while drilling; MWD) for a more effective planning of the blasting process in surface mines. A more accurate and reliable digital drilling and automatic hardness identification technology was developed, which includes both a hardware and software system. In the aspect of hardware, we designed a positioning, navigation and hardness perception terminal system which consists of a global positioning system original equipment manufacturer board, programmable logic controller and sensors of measuring major parameters, and a wireless data transmission system which combines digital blasting platform and wireless transmission facilities. In the aspect of software, we developed the navigation software of locating blastholes using LabVIEW and C++, and the blasthole design software using AutoCAD ActiveX (C#) technologies. This new technology is applied at Jiangxi Dexing Copper Mine, and initially realising the digitisation of drilling and hardness identification in blasting zone.CITATION:Duan, Y, Xiong, D, Yao, L, Wang, F and Xu, G, 2015. Advanced technology for setting out of blastholes and measurement while drilling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 593–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A Purwodihardjo

Evaluation of the construction method used for the pedestrian underpass construction at Ipswich Road, Brisbane, Australia is presented in this paper. The pedestrian underpass was constructed through the existing railway embankment between Harrogate and O’Keefe Streets on the eastern side of Ipswich Road. This underpass construction is part of the CLEM7 tunnel project (formerly known as the North-South Bypass Tunnel) which is the longest toll road in Australia at a total length of 6.8 km. The jacked box construction technique was initially identified as a preferred option during the tender and concept design phases. However at the final design stage, the cut and cover technique was selected as this method can reduce the construction time and cost significantly. The design and construction teams effectively managed the challenges, complexities and risks associated with undertaking cut and cover tunnel through the existing heavily utilised rail embankment. The on-site construction time for the underpass using the cut and cover technique was reduced to less than 42 hours.

Mar 8, 2011

By H Arvidson, D Guibal

This paper presents updated interpretations of controls on mineralisation in C Deposit and highlights structural features that influence the geometry of mineralisation domains used in resource estimation. The Area C mining lease is located in the central Hamersley Province, ~100 km WNW of Newman, Western Australia, and contains resources of approximately 1100 Mt of Marra Mamba and Brockman iron mineralisation. C Deposit is located within Area C, on the northern limb of the Weeli Wolli anticline, and mineralisation is hosted predominantly in the Mt Newman Member of the Marra Mamba Formation. Production from C Deposit began in August 2003, following mining of a 950 000 tonne bulk sample in 2002. Recent mapping in the bulk-sample pit and updated interpretations by BHP Billiton geologists have highlighted the significance of structural controls on mineralisation in C Deposit and their influence on the thickness of mineralisation, which ranges from 20 to 80 metres. Structural controls on the geometry and continuity of mineralised domains include south-dipping thrust faults that developed along the Mount Newman/West Angela contact, folds associated with thrust fault development, steeply dipping stratigraphic contacts in the hanging wall of the thrust faults, and gently north-dipping stratigraphic contacts. Thrust faults and folds in C Deposit are significant for two main reasons: their formation resulted in the thickening of the main ore-hosting units in the Mount Newman Member; and faults and folded stratigraphic contacts provided conduits for supergene metasomatic-enrichment processes that produce high-grade iron mineralisation.The implications of this interpretation for the definition of the resource estimation domains are discussed, and suggestions are made for a better integration of geology into the data acquisition and estimation process.

Jan 1, 2005

By F F. Pitard

Observation from attending many conferences around the world reveals that many people are constantly shifting from the word ‘error’ to the word ‘uncertainty’ without a clear vision of what the subtle difference is. The same applies to a large swath of the scientific literature, in which these two concepts are unfortunately often used synonymously, which is a scientific flaw of the first order. In practice, as demonstrated in the Theory of Sampling (TOS), there are both sampling errors and sampling uncertainties. Sampling errors can easily be preventively minimised, while sampling uncertainty for a preselected sampling protocol is inevitable. P M Gy’s work, supported by G Matheron’s critical reviews, demonstrates beyond any possible doubt that sampling uncertainty cannot be achieved if sampling errors are not preventively minimised by applying very stringent rules that are too often ignored by sampling practitioners. A clarification, in line with the TOS, is presented to mitigate the confusion created by circles favouring the use of uncertainty versus the use of the word error. Both words are very different in nature and scope and they are both necessary in their due place and time.CITATION:Pitard, F F, 2017. From errors to uncertainty – a clarification for proper use by the Theory of Sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 355–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

The first stage in process design for coal preparation is a study of the coal seam and its associated features followed by an examination of the mining method to.be employed and the coal market requirements. Normally benefication is based upon the differences in relative densities of the coal constituents and asso- ciated ash forming components. Since initial liberation is obtained at a relatively large particle size, the size to which coal is crushed is more subject to the market requirements than to liberation studies. It is possible to estimate energy requirements for comminution and recoveries and product grades can be cal- culated following the interpretation of standard laboratory tests. Numerous units are available for the separation and concentration of the components of run of mine coal in- cluding jigging, dense media separators, and for the finer particle size fractions, flowing film separators, dense media cyclones and froth flotation.

Jan 1, 1975

By G Maude, R Ayres, R N McLean, N A. Reynolds

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Mabilo copper-gold-magnetite skarn deposit is located in southern Luzon in the Paracale mineral district, where iron has been produced historically from several skarn deposits. Mabilo occurs in the south-west of the district and is distinct and significant because of its high grades of copper and gold compared to historical mines.The Mabilo licence surrounds the Venida prospect, where past small-scale mining has exploited iron, copper and gold mineralisation in oxidised skarn. A ground magnetic survey in 2007 defined a number of strong anomalies under Quaternary volcanic cover south of Venida. The property was acquired by Sierra Mining Ltd in 2011, the magnetic data were remodelled and drilling commenced in September 2012. Diamond drill hole MDH001 targeted the strongest anomaly, which was 500 m south of Venida and under 20 m of volcanic cover. It intersected 94 m with an average grade of 2.2 per cent copper, 1.6 g/t gold and 36.6 per cent iron. Subsequent drilling was targeted by magnetic modelling, incorporating magnetic susceptibility data from drill core, which resulted in a high percentage of successful drill holes.The mineralised skarn preferentially replaces a dipping limestone unit within an Eocene sequence dominated by volcanic siltstone and sandstone, metamorphosed to marble and hornfels in the aureole of a Miocene quartz-diorite intrusion. Skarn occurs discontinuously along the eastern and southern diorite contact, controlled by primary sedimentary facies variation, structural geometry, fault offsets and intrusive contacts.Coarse magnetite skarn with garnet and minor wollastonite and clinopyroxene contains variably abundant chalcopyrite and minor molybdenite. Magnetite skarn occurs in sharp contact with unaltered marble or grades into garnet skarn with minor chalcopyrite. Structurally controlled retrograde skarn alteration is strong to intense and is characterised by bornite, clinozoisite, iron carbonate and chlorite. The retrograde skarn is weakly overprinted by late-stage pyrite veining and brecciation associated with clay-silica alteration with arsenopyrite and tetrahedrite-tennantite.The quartz-diorite stock is interpreted as the source of the prograde skarn-forming and mineralising fluids. Late-stage porphyritic intrusions in the contact zone indicate continuing magmatism during uplift, when telescoping led to a high-level, high-sulfidation overprint. This suggests the potential for deeper porphyry-style mineralisation.CITATION:Reynolds, N A, Ayres, R, McLean, R N and Maude, G, 2015. The Mabilo copper-gold-iron deposit – a new skarn discovery in the Philippines , in Proceedings PACRIM 2015 Congress, pp 431–438 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015