Search Documents

By S. Stutz

COAL, like most other minerals, only exceptionally occurs in a sufficiently pure state to he directly available for general manufacturing purposes. And even where this is the case, the small coal or slack is usually more impure than the lump coal, as the slate, clay, etc., from the roof and bottom of the vein become mixed with it in the handling it undergoes. These impurities often exceed ten or more percent in addition to the impurities of the coal itself. The most common impurities of the coal are slate, or shale, clay, and sulphur. The latter occurs in different forms, but most frequently as bisulphide of iron, or iron pyrites, and as sulphate of lime, or gypsum. In both cases the impurities add greatly to the amount of ash, and where they are present in considerable quantities the raw coal, and still more the coke made from it, is unfit for the, manufacture of iron. Coke will contain on an average at least ;fifty per cent, more ash and sulphur than the raw coal from which it is, made. To the manufacturer of iron every additional per cent. of ash which his coal or .coke contains is a source of additional expense, seemingly small, and yet very important in the aggregate. In the blast-furnace, for instance, the ash must be heated up to the melting-point, and, since it is composed largely of refractory substances, the consumption of carbon in melting it will be equal to at least one-half of its weight ; that is, a certain part of the coke is consumed for the melting and fluxing of the ash and is lost. Besides this, it is well enough known to the-iron-master that coke containing less ash makes the slag or cinder more liquid and less inclined to stick to- the walls of the furnace. Fuel containing much sulphur produces generally a white iron, poor in carbon, while from the same ore and flux, with a pure fuel, a good foundry iron might be obtained. The work of separating slate, sulphur, etc:, from the coal 'has as yet only been succesafully accomplished by the washing process. This process depends for its success on the differences in the specific

Jan 1, 1881

By Thomas D. Henderson, Donald E. Crowell

INTRODUCTION This paper presents a "case history" of the steps taken to estimate capital and operating costs for a typical porphyry copper concentrator of ±9,070 metric tons (10,000 short tons) per day capacity. The concentrator described herein is hypothetical, but is based on experience and is, in effect, a composite of several actual projects. The numbers used are illustrative only and do not represent actual costs at any particular concentrator. These numbers are, however, representative of typical milling costs at one point in time, and. are sufficiently accurate to illustrate the cost estimating procedures described in this paper. It is not possible to publish actual, current milling costs and, in any event, actual cost figures quickly become meaningless in today's economic situation with various costs all rising at different rates. The paper is divided into three parts: (1) order-of-magnitude estimate, (2) feasibility study estimate, and (3) discussion of differences between estimated and actual costs.

Jan 1, 1978

By J. J. Rutledge

I. Description of the Clinton Ores and Associated Rocks. The Clinton rocks in Stone valley comprise (1) thick layers of deep-red shale, (2) layers of reddish-gray shale interspersed with beds of sandstone and thin beds of extremely fossiliferous limestone, and (3) yellowish-gray shales alternating with thin layers of olive-colored shales. These layers of shale are all very thin and are at no point massive.' A bed of gray-white sandstone varying in thickness from 12 to 30 ft. occurs in the upper portions of the Clinton shales. This is called the ore sandstone, a name given to it by Rogers and adopted also by the Second Pennsylvania Geological Survey. It is the surest guide to the presence of the iron-ore bed, which lies below its lower edges at distances varying from 10 to 20 ft. This ore sandstone, in the valley, lies generally at very low inclinations, but often is locally subjected to considerable changes in dip. At its outcrop this ore sandstone weathers very easily and yields a rather sparse crop of stone, composed of dirty, iron-stained boulders. Upon the roads these boulders are quite well rounded, and bear fragments of crinoid stems and other fossil forms. The ore sandstone exhibits at many points evidences of former movements in this very great thickness of the shales, and as it is the only stratum in this series competent to transmit and record stresses due to structural movements, its evidence is of considerable importance in determining the occurrence of movements in times past.

Jan 1, 1910

RichaRd PeaRce, Argo, Colo.: This contribution upon the very interesting subject of the origin of the gold of certain lode-formations offers many subjects for thonghtful consideration. The explanation, for instance, of the perplexing features of thin lava dikes seems to me to be in harmony with facts as I have myself observed them elsewhere. At Marshall basin, near Telluride, Colorado, there is an extensive lava-flow. The material of this formation contains a large proportion of fragments of foreign matter in the form of angular pieces of rock. The latter show no signs of having undergone metamorphism, such as would be expected to be due to the direct effects of heat; and the evidence in this particular case would certainly lead me to suppose that the flow was due to causes analogous to those suggested by Mr. Rickard. It was, I believe, a moving mass of material, having a temperatrire considerably below the actual melting-point of the rock of which it is composed. In regard to the theory which the author has built up from the existence of the iodide of gold in sea water, I cannot consider it untenable ; but I would put the question whether any investigations have been made with a view to determining whether gold and silver occur in the beds of rock-salt, formed, as is generally allowed, by the evaporation of bodies of salt water. At Stassfurt, in Germany, there is a very remarkable series of alternating beds of rock-salt and anhydrite, the uppermost members of which are covered with deposits of potash salts. The question occurs to me, why should not gold and silver have been discovered in these deposits? Iodine and bromine, I believe, have been found in the salts last deposited by

Jan 1, 1894

By Louis Katona

The practical execution of the design for rolling-mills presented by the writer at the Paris meeting* of thc Iron and Steel Institute in 1900 involves the determination of some questions not yet discussed, among which is the determinatioir of the amount of power required to perform the rolling of pieces of iron and steel of given dimensions. It is necessary to know this factor if we would put motors of proper capacity to the respective pairs of rolls, or, rcciprocally, if, having standard motors at our disposal, we would design grooves to suit them. Moreover, this factor is involved in giving right dimensions to every part of the rolls and housings. Expert designers of engines for driving rolling-mills of the present type receive very indefinite directions, such as: that the motor is to drive a light, medium or heavy train; that it must work with fly-wheel or reversing gear; that the number of revolutions per minute should not exceed 40 or 60, and that at a given speed the power developed should be from 100 to 200 H. P., or from 1,000 to 2,500 13. P. It frequently happens, however, that an cngine of 200 H. P. is forced under the circumstances to press or develop as much as 300 H. P., while, on the other hand, the ,1,500-11. P. engine may be rolling-stock which could be worked with a maximum expenditure of 60 to 80 H. P. Of course such variatior~s as these do not permit the best adjustment of parts or the best economy of power and fuel. The design of roll-trains is even more vaguely limited. Every part of a train, from the point where it connects with the engine to the last groove in the rolls, bears evidence that there are no rules for calculating even approximately the dimensions of the main-shafts, couplings, pinions, gears, rolls, trunnions,

Jan 1, 1904

A little more than a year and a half ago construction started on Canada's largest initial milling plant. Today the zinc concentrating plant 7 miles north of Barraute sits on ground that once was forest and clay flats. The plant is part of Barvue Mines Ltd. zinc-silver operation. Employees of the plant live in the model community of Barvue, built like the plant in record time. About 5000 tons of ore are handled by the plant daily, with an output of 200 tons of zinc concentrate. Management hopes to raise capacity of the $8 million plant to 6000 tons.

Jan 8, 1953

By John R. Green

Rotary kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary accorcling to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. Measurements of Kiln Temperature The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records ox automatic control are desired, while Optica1 pyometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. 1 shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected From puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly 0" to over zoo°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without effect of the flame temperature. There should some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and comments on the possibility of measurement and control. Of greater number and of varied influence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1942

By John R. Green

Rotary kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary accorcling to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. Measurements of Kiln Temperature The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records ox automatic control are desired, while Optica1 pyometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. 1 shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected From puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly 0" to over zoo°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without effect of the flame temperature. There should some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and comments on the possibility of measurement and control. Of greater number and of varied influence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1942

By Joseph E. Pogue

The past year in the petroleum industry was one of overproduction, rising inventories, low prices, and meagre to vanishing profits. This outcome was the result of a long period of intensive and uncompensated effort on the part of both financial and industrial interests, to stimulate supply on the theory that the primary problem facing the petroleum industry was the development of an adequate reserve of raw material to protect a large and ever-growing investment. The stimulus was applied in various forms and through diverse channels: capital had long flowed into the industry in excessive amounts under the attraction of large expected profits; the price level for crude petroleum had persistently been influenced by speculative considerations, with the result that prices declined slowly in periods of flush production and were quick to advance in anticipation of statistical improvement, thus maintaining a superfluous degree of stimulus on wildcatting and on drilling; speculation in inventories had led to the unsound, or at least unusual, business practice of accumulating huge stocks of oil; and, above all, the industry had directed the potent force of technology to the expansion of supply and achieved radical results in accelerating oil discovery, speeding up the rate of oil extraction, and enlarging the recovery of gasoline and lubricating oils from the raw material. In short, the economic conditions of 1927 were exactly those to which the objectively driven enterprise of the petroleum industry had long been directed; and the undesirable financial consequences arising therefrom reflected no lack of success in what had been set out to be achieved, but rather the failure to have established concurrently the necessary means of economic control to prevent the immediate conversion of reserves into current supply, and likewise the oversight in neglecting to apply the technological force to the enlargement and diversification of the market for petroleum products. Perhaps, when viewed in its longer perspective, 1927 will stand out as the turning point in the economic policy of the petroleum industry, when the technique of rationalizing production made its initial claim for recognition.

Jan 1, 1928

By A. Schild

The effect of heating a producing well on the rate of oil recovery has been analyzed in the simple case of a well producing oil by a radial drive and in the steady state. Differences of production rates with and without borehole heating have been calculated and plotted; these measure some of the benefits of the thermal recovery process. A striking feature is that the production increase tends rapidly to a constant value for large production rates. Some concrete examples, including a rough comparison with field data. are discussed. Heating requirements have been calculated and plotted on the assumption that the heaters used are 100 per cent efficient. Heating has been thought of as applying only to low volume wells producing heavy oils. However, the calculations suggest that the thermal process considered might be profitable even for some wells producing large quantities of light oil, especially in unconsolidated formations where fracturing is not possible. In the case of wells producing other fluids with the oil or of wells producing partly or wholly by gravity drainage, the theory developed does not apply in detail. It can be expected, however, that any general qualitative be-havior will remain valid. Under normal temperature conditions, high viscosity emulsions sometimes form around the wellbore, lowering the permeability in the vicinity of the well and impeding the production of oil. Borehole heating often prevents such emulsification. This important effect is not easily amenable to mathematical analysis and has not been included in the theory presented here. It should therefore be kept in mind that the benefits due to borehole heating may in fact exceed the values given by the following calculations. INTRODUCTION The recovery of viscous, low gravity oils can often be stimulated by applying heat to the production zone. The higher temperature lowers the viscosity of the oil, increasing its mobility, and therefore its rate of production. One thermal method of recovery 1,2,3,4. consists in operating a heater inside a producing well and, at the same time, producing oil from the well. In this paper a simple theoretical model is analyzed to study the effect of such heating on the recovery of oil. The reservoir mechanics of the process is the only aspect of the problem which is considered here. The details of the heating system are ignored, and it is simply assumed that the heater raises the temperature in the immediate vicinity of the producing well to a pre-assigned temperature T w. Although heating requirements are calculated, these refer only to the heat supplied to the formation and to the oil being produced; they do not include heat losses due to the inefficiency of the heater. A short outline of the theory follows: The heat supplied to the producing well flows out into the formation by means of thermal conduction. At the same time, the flow of oil carries heat by convection from the formation towards the producing well. After sufficient time has elapsed, a steady-state is reached where the temperature, the velocity of the oil, etc., no longer vary with time but are functions of position only. In the steady state the temperature decays like an inverse power from the high value Tw at the wellbore to the original reservoir temperature T. at some distance away from the well. The effect of the high temperature and low oil viscosity near the producing well is the same as if the oil were produced at reservoir temperature To but through a producing well of a larger radius. From this point of view, the energy and money being expended to provide heat

Jan 1, 1958

By D. W. Duncan, A. Bruynesteyn

An ore containing chalcopyrite was microbiologically leached in 6 ft columns at particle sizes ranging from -2 +1 ½ inches, to -3/8 + 3/16 inches. The rate of leaching increased exponentially as the particle size decreased. The controlling factor was the active leaching volume made up of the particle surface area and the depth of penetration of the bacteria and leach liquor into the particle. This volume became an increasingly larger part of the total volume as the particle size decreased. The sample under test leached poorly at larger particle sizes and it was calculated that under commercial conditions, it would produce at best a pregnant solution containing 100 mg/l (0.2 lb/ ton) of copper per 100 ft of dump height.

Jan 1, 1974

By L. S. Castleman, L. L. Seigle

THE formation and growth of intermetallic phase layers is of considerable practical importance to metallurgists interested in diffusion bonding and cementation processes and has been the subject of extensive qualitative investigation. In contrast, it is somewhat surprising that so little quantitative data have been amassed. The need for additional fundamental work was pointed out by Mehl in 1936,' and persists to a large extent to the present day. The early studies have been reviewed by Rhines,2 and his conclusions have been summarized by Lustman and Mehl3 substantially as follows: 1) All phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two metals; however, in some cases, certain of the phases may be too thin to be observed and identified easily. 2) The isothermal growth of intermetallic phases generally obeys a simple parabolic equation of the form X2 = Kt, where x is the thickness of the alloy layer, K the temperature dependent reaction rate constant, and t the time. 3) The rate of thickening varies with temperature according to the Arrhenius equation k = Ae -Q/RT , where k is the parabolic rate constant, A, a temperature independent constant, Q the heat of activation for the process, R the gas constant, and T the absolute temperature. Subsequently, Lustman and Mehl made a quantitative study of the laws of growth in intermediate layers in a number of binary systems, in which one of the components was either zinc or cadmium, and the other component was one of the following: nickel, copper, silver, cobalt, gold, iron, or Monel metal; the interdiffusion times used were for the most part less than 24 hr. It was found that the simple parabolic law was not obeyed in general, but that a generalized parabolic law of the form xn = kt was valid, where n was a temperature dependent constant; also,

Jan 1, 1959

By Leo D. Jones

The use of the centrifuge for dewaxing lubricating oils grew out of the effort to secure better results than had been attained by the common "cold settling" process. This process was the only known method for dewaxing steam refined cylinder stock (600" F. fire test), the product known as "bright stock" being commonlyused for building up "pressed," i.e., dewaxed neutrals of, say, 200-sec. viscosity [to a higher value. The process consisted of mixing the cylinder stock with approximately one and one-half times its volume of naphtha, heating, to dissolve completely all the oil and wax and then slowly chilling to about 15" F. in large insulated tanks. This caused the wax to precipitate. It was allowed to settle out by gravity. The supernatant liquid was then drawn off and the naphtha distilled off, leaving a still residue of bright stock. The sediment from the settling, of a slushy nature, was withdrawn. After removing the naphtha by distillation the residue was petrolatum. At some point in the process, preferably after the dilution but before chilling, the mixture was decolored by percolation through fuller's earth. The finished bright stock produced by this process had a cold test of about 50" F. Efforts to improve this by chilling to a lower temperature resulted in a considerable reduction in yield, and increased uncertainty of settling. Even when chilling to 15" F. it was not uncommon to find that after a week's waiting a tank had not settled. It was then necessary to heat and rechill. This uncertainty was a serious problem; in one case a refinery superintendent had men riveters hold pneumatic hammers against the tank for hours, hoping thus to cause agglomeration and settling of the wax. Yields of bright stock above 70 per cent, were uncommon. History of Centrifugal Application It is not surprising, therefore, that many attempts were made to improve upon the results obtained by cold settling. George H. Taber, vice-president of the Gulf Refining Co., Pittsburgh, Pa., made a number

Jan 1, 1924

By Frederick Laist

The ores received at the Washoe Smelter come almost entirely from the mines in Butte and contain the following minerals : Chalcocite, Cu2S; covellite, CuS; chalcopyrite, CuFeS2, (trace); bornite, Cu3FeS3; enargite, Cu3AsS4; malachite, Cu2CO4 + H2O (trace); pyrite, FeS2; sphalerite, ZnS; rhodo-chrosite, MnCO3, (less than 1 per cent.); rhodonite, MnSiO3, (less than I per cent.). The country-rock of Butte is of the granite family and is a quartz-monzonite containing a little less silica than typical granite. It is made up of the following rock-minerals in approximately the proportions indicated: Minerals. Composition. Per Cent. Quartz SiO2 20 Andesine 1/2 NaAlSi3O8; 4 CaAI2Si2O8 42 Orthoclase KA1Si308 23 Hornblende 1/2 Ca(MgFe)3Si4O12; & (MgFe)2(AlFe)4Si2O12 6 Biotite (HK)2(MgFe)2A12Si3O12 9 Titanite CaTiSiO5 0.1 Apatite (CaF)Ca4(PO4)3 0.05 Magnetite (FeO)(Fe2O3 0.15 Pyrite FeS2 0.02 99.32 The main country-rock (quartz-monzonite) is cut by dikes of aplite, a granite having the following composition: Quartz, 30; andesine, 20; orthoclase, 45; ferro-rnagnesian minerals, 3; pyrite, 0.1; total, 98.1 per cent. Closely associated with the copper-deposits are dikes and bodies of " Modoe" porphyry, technically known as quartz-

Jan 1, 1913

By Laurence C. Hicks

Consideration of the past work on the subject of the diffusion of chromium into iron suggested that additional information might be given by the use of X-ray spectroscopy in following the concentration changes through the diffusion zone. Grube and Fleischbeinl packed rods of electrolytic iron in a mixture of alumina and chromium. These specimens were heated in an atmosphere of purified hydrogen for varying lengths of time. After treatment the specimens were examined metallographically and showed the usual structure, consisting of a border of radially oriented columnar grains ending in a sharp boundary line. Reference is made to the fact that etching with certain reagents will attack only the material inside the border of columnar growth and also to the fact that polishing seems to develop a ridge at the position of the boundary between the etched and unetched areas. By chemical analysis of thin layers turned off on a precision lathe, the authors were able to obtain depth-concentration curves. These curves, reproduced in Fig. 1, show that in most cases a pronounced change of slope occurs, corresponding to the position of the boundary of the columnar grains. In a laler paper Grube extends his work to other systems which show the same characteristics.~ He concludes that the reason for the break in the curve is that a hindrance of diffusion occurs at the place where the regularly oriented grains of the diffusion zone meet the random grains of the interior portion, on the assumption that the diffusion velocity in one direction in a grain may be greater than in another direction, and that the grains in the diffusion zone orient themselves so as to give the maximum diffusion rate. Kel1ey" points out that Grube has failed to note that the boundary line does not consistently cross all grains and

Jan 1, 1934

By John R. Green

ROTARY kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary according to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. MEASUREMENTS OF KILN TEMPERATURE The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records or automatic control are desired, while optical pyrometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. I shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected from puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly 0° to over 200°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without effect of the flame temperature. There should be some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors Influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and comments on the possibility of measurement and control. Of greater number and of varied influence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1941

By Shiou-Chuan Sun

THE effects of oxidation on the flotation behavior of sulphide minerals have been extensively studied,1-3 but no similar study has been made of coals. Coals of bituminous and lower rank undergo atmospheric oxidation during mining and storage, and their degree of oxidizing increases with temperature4,5 and time of exposure.6 The problem of recovering fine oxidized coal from culm piles, rivers, and streams by froth flotation has become increasingly important to the coal industry as well as to those concerned with air and stream pollution. This paper describes the flotation behavior of oxidized and unoxidized coals and carbons in the presence of oily collectors and presents the reagents found effective in the flotation of oxidized coals and carbons. Except where otherwise stated, flotation tests were performed in a 50-g Denver flotation cell. Solid feed for each test was 30 g, and the pulp dilution was kept at 8.5. The -65 mesh coal sample was wetted by agitation with water in the flotation cell for 6 min, then conditioned with a predetermined amount of collector for 2 min, and finally floated with pine oil as frother for 3 min.

Jan 4, 1954

By Will Mitchell

There are in this country some 20 or 30 societies for engineers and engineering scientists. Most of these organizations are autonomous, and there is little or no cooperation among them. Many do not touch the lives of our Institute members. However, during the course of the years several societies closely associated with the AIME have banded together to handle specific situations where cooperation was necessary. It is believed by many engineers that the functions of these cooperative societies should be analyzed and a plan set up to unify the engineering profession into an organization similar to the American Medical Association and the American Bar Association. The preliminary study of the AIME Committee for Inter-Engineering Society Cooperation has indicated that the following organizations bear upon the professional lives of our members. Some of these are federated groups, such as EJC and ECPD; others are individual-member participation groups, such as the Founder Societies and NSPE.

Jan 10, 1960

By Arthur C. Simmons

The area that produces Pennsylvania grade, which includes New York, Pennsylvania, West Virginia and a part of Ohio, increased its production in 1942 about 1,580,000 bbl. over that attained in 1941. Such an increase is substantial for this area, and measured in terms of increased output of lubricants, for which the crude is particularly suitable, it represents a needed arid worth-while addition to the lubricant resources of the United States. The year 1942 was a difficult operating period for most of the petroleum-producing areas in the United States, but the Appalachian region, owing principally to its location, type of operations, and crude value, suffered less from war influences than other areas. The state of Pennsylvania produced 17,823,870 bbl. of crude oil, which is approximately 63 per cent of the total production of Pennsylvania grade in the entire area. Production Bradford Field The Bradford field, which produces almost wholly by water-flooding methods, increased its production nearly 4000 bbl. per day over 1941 despite a very slight reduction in total number of wells completed. Well completions in the Bradford field (in both New York and Pennsylvania) includc both producing oil wells and water-intake wells. About half of the well completions are producing oil wells and the remaining half are water-intake or injection wells. About 10 per cent of the total well completions of the Bradford field were in Cattaraugus County, New York. No segregation of well completions is available, so that precise statistics cannot be given for New York and Pennsylvania.

Jan 1, 1943

By Arthur C. Simmons

The area that produces Pennsylvania grade, which includes New York, Pennsylvania, West Virginia and a part of Ohio, increased its production in 1942 about 1,580,000 bbl. over that attained in 1941. Such an increase is substantial for this area, and measured in terms of increased output of lubricants, for which the crude is particularly suitable, it represents a needed arid worth-while addition to the lubricant resources of the United States. The year 1942 was a difficult operating period for most of the petroleum-producing areas in the United States, but the Appalachian region, owing principally to its location, type of operations, and crude value, suffered less from war influences than other areas. The state of Pennsylvania produced 17,823,870 bbl. of crude oil, which is approximately 63 per cent of the total production of Pennsylvania grade in the entire area. Production Bradford Field The Bradford field, which produces almost wholly by water-flooding methods, increased its production nearly 4000 bbl. per day over 1941 despite a very slight reduction in total number of wells completed. Well completions in the Bradford field (in both New York and Pennsylvania) includc both producing oil wells and water-intake wells. About half of the well completions are producing oil wells and the remaining half are water-intake or injection wells. About 10 per cent of the total well completions of the Bradford field were in Cattaraugus County, New York. No segregation of well completions is available, so that precise statistics cannot be given for New York and Pennsylvania.

Jan 1, 1943