Search Documents

By W. J. Slatosky

As a means of effecting better control of endpoint temperatirres at the Jones & Laughlin basic oxygen furnace plant, a set of mathematical equations has been developed. The eqlutions are the product of a themlochemical anaysis of the process and aye designed to calculate the required scrap, lime, and hot metal additions in terms of a number of independent variables. Results of test heats have warranted adoption of this technique by the Prodrrction Department. BECAUSE of the autogeneous nature of the basic oxygen steel-making process, bath temperature can be controlled without an external fuel supply by charging the furnace with additions that are thermally balanced. The thermal requirements of the charge materials are such that, during the refining process, they throttle the heat generated by the metallurgical reactions in a manner designed to result in a speci-fied temperature at the completion of the heat. In the past, operating personnel at the basic oxygen furnace plant of Jones & Laughlin's Aliquippa Works relied on their experience and technical knowledge of the process to determine the quantities of charge additions needed to result in a finishing temperature in the range 2880"to 2920" F. (The charge consists primarily of 93 tons of scrap and hot metal plus an amount of lime sufficient to maintain a basicity ratio of 2.8 to 3.2). Estimates of these materials are based on a consideration of the effects on finishing temperature of 1) iron silicon content, having a variation of 0.8 to 1.8 pct; 2) iron temperature, ranging from 2250°to 2600°F; and 3)any excessive cooling of the furnace due to a production delay. The end temperature of the preceding heat also serves as a guide in that, if a heat was within the specified temperature range, the succeeding heat could be charged with materials of nearly the same proportions, provided the hot metal used in each of the two charges was of approximately the same temperature and composition. On the other hand, if a heat was outside the specified tapping range, or if the hot metal used in that heat was of different analysis and temperature from that of the iron to be charged, an adjustment in the proportion of additions is in order for the following heat. Due to the complex thermochemical behavior of the process and to the inexact and subjective nature of the described method of determining charge additions, consistently accurate temperature control was not to be expected. Therefore, those heats out- side the specified tapping range necessitated subsequent adjustments by either reblowing the cold heats for a suitable length of time so as to elevate the bath temperature to the desired level, or cooling hot heats with a proper amount of scrap. Because extra time is required to make these adjustments, production is delayed. In an attempt to devise a method for improving temperature control, an analysis of the thermochemistry of the process was undertaken. This, in turn, led to the development of a set of mathematical equations which enable the calculation of the quantities of scrap, lime, and hot metal needed to result in any specified tapping temperature range. The analysis was not intended to be a repetition of work done by others such as McMulkinl or ~hilbrook.' It was meant to be an extension of their work so that charge additions could be calculated not in terms of silicon alone but, rather, as a function of all independent variables. This paper presents the derivation of these relationships, their effectiveness in controlling bath temperatures, and a method of utilizing them on an operational basis. The Heat Balance—The first step undertaken in the analysis of the problem was the enumeration of the pertinent variables. A list is presented in Table I where it is noticed that these quantities have been separated into the following three categories: important variables, variables considered as constants, and variables to be neglected. The breakdown was an arbitrary one designed to facilitate the analysis; otherwise, the mathematical treatment would have been exceedingly cumbersome and complex. Fortunately, experience has shown that these simplifying assumptions do not seriously impair the accuracy of the calculations. These variables along with the limiting assumptions listed in Table n were then used to write a heat balance of the process by applying the equation of continuity, Rate of Rate of Rate of Increase = Income - Outgo PI ] of Heat of Heat of Heat.

Jan 1, 1962

By Charles Catlett

Having had charge during the past year of the operations of the New River Coke Company, the second largest, if not the largest, coke-producer in this district, my attention was called particularly to the yield of coke from the coal as coked in a bank of beehive ovens, as the record showed that this yield, while believed to be well up with the practice of the district, was much lower than the analysis of the coal indicated it should be. The coal is well known to many members of the Institute, and the scope of this paper does not include a discussion of its occurrence and development. It suffices to say that the New River district comprises the mines working on the coals of No. XII. or the Conglomerate Series of the Rogers brothers, which are located on New river and its tributaries, and which find an outlet for their product east and west over the Chesapeake and Ohio Railway. The New river through this section carries the drainage from an extensive peneplain in which it has formed a very striking and stupendous canon, probably the most striking east of the Mississippi river. The only practical access to this territory is by means of this canon and the Chesapeake and Ohio road, and the opportunities for development by other lines may be considered as nil. If it were not for the fact that this road, farther west, reaches and develops entirely different coals, which are found in other measures, the New River district might properly be spoken of (as is now done at times) as the " C and 0. field." For fuller information on the geology of the region, those interested are referred to the ery complete monograph on the subject by Mendenhall and Campbell of the United States Geological Survey. The rocks are the same as those which carry the more widely

Jan 1, 1900

By R. D. Pehlke, J. V. Gluck

A study was made of' the effects of up to five additional solutes on the thermodynamic activity of zinc in dilute solution with molten bismuth in the range 450" to 650°C. The experimental measurements were made in a multielectrode galvanic cell apparatus employing fused LiCl-KCl as the electrolyte. The solute additions included indium, lead, tin, cadmium, copper, silver, antimony, or gold. A range of positice and negative interactiotls with zinc was covered. The experinzer~tal observations were cowlpared with the activity coefficients calculated usitlg either Wagner's first-order Taylor series rnodel or a proposed second-order solution itrteraction model. hi general, the truncated first-order Taylor series proposed by Wagner gaue good results for "dilute" solutions (XBi > 0.90) contaitzing up to six solutes. The second-order model, which includes a second-order cross-interaction term, produced a slight improvement in predictions for solutions with XZn = 0.015 and a significant improvement for solutions with XZn = 0.050 hear the limit of Henry's law region). Seveval of the quaternary solutions studied contained a total solute content of 0.215 mole fraction, and fairly good success was achieved in predicting the activity coefficient 01- zinc. ThE study of thermodynamic interactions between dilute solutes in liquid metallic solutions has occasioned much recent interest. It is useful to recall in this respect that Wagner's well-known expression for the activity coefficient' is a practical application of the problem of representing a given function, i .e., In ?, by means of a sequence of polynomials. No specific physical model of a solution is involved in its use. As suggested by Wagner, a Taylor Series is used to expand In ? about a point of infinite dilution with respect to all solutes. The partial differential coefficients of the series have been termed "interaction parameters". Various authors'-6 have proposed formalisms for parameters, the definitions being designed to meet some specific experimental or physical condition. A usual assumption is that terms above first-order in the Taylor Series may be neglected. In that case, the logarithm of the activity coefficient is expressed as a linear function of solute concentrations. The resulting expression is presumed valid for any number of additional solutes as long as the solution can be regarded as "dilute". This assumption can be termed "the hypothesis of additivity". However, experimental tests of that hypothesis for quaternary or higher-order solutions have been extremely limited. Primarily such tests have been confined to studies of effects of added metallic elements on either the activity of carbon or the solubility of gases in liquid iron.7-13 The only known previous study of an all-metal system is the limited work of Okajima and pehlke14 on the effects of multiple solute additions on the activity of cadmium in liquid lead. The present investigation is a portion of the work to determine the effects of various solute additions on the activity of zinc in dilute solution with molten bismuth in the range 450" to 650C It was shown for such ternary solutions that second-order Taylor Series terms could be evaluated at the same time as first-order terms, with no additional experimentation required. A second-order solution model was described which, under certain conditions, is a rigorous representation of solute activity in a ternary solution. (In the sense employed in this paper, the term "model", as distinguished from "equation", is taken to mean an empirical correlation or formalism, but not a hypothetical physical system per se.) Presumably such a model could be extended to produce a better representation of In ? in solutions of even higher order. The feasibility of a generalized Taylor Series approach to solution interactions and inclusion of second-order terms also has been discussed recently by Lupis and Elliott in independent work concurrent with the present investigation. In addition, they discussed empirical means of estimating certain second -order coefficients.17 The utility of such solution models rests on the ability of a truncated series to represent adequately the experimental facts in multicomponent solutions. Questions that arise include: Do the second-order terms really make a significant contribution? How far away from "dilute" solution may such models be applied? Are the types and varieties of the additional solutes important? among others. In order to provide some answers to these questions, an experimental study was made of the effects of two or more additional solutes on the activity of zinc in dilute solution with molten bismuth. Comparisons were then made with calculated activity coefficients obtained using the previously determined ternary interaction parameters. INTERACTION MODELS As an example of the approach to defining activities in multicomponent solutions, consider the Taylor Series expansion for a quaternary system, i.e., three dilute solutes. Writing terms through second order, the result is:''

Jan 1, 1968

By Richard S. McCaffery, Clarence H. Lorig, Joseph F. Oesterle, Ira N. Goff, Oscar O. Fritsche

This paper is the report of an investigation to determine the relations between the viscosity, temperature and composition of that portion of the silica-alumina-lime-magnesia system(l) within which blast-furnace slags are found. The work reported in this paper was made possible by a grant of funds from Engineering Foundation. It is a part of a project, the determination of properties and structure of iron blast-furnace slags, upon which the laboratories of the University of Wisconsin have been at work for some years. Three papers have been published, which have marked the progress of the study of iron blast-furnace slags at Wisconsin. The first,(2) Desul-furizing Power of Iron Blast-furnace Slags, discussed the solubility of sulfur in slags that contained no magnesia and discussed the viscosity. The second, (3) The Constitution of Iron Blast-furnace Slags, developed the constitutions of slags in the four-component system, silica-alumina-lime-magnesia, and pointed out an explanation of slag structure. Composition of Iron Blast-furnace Slags,(l) which was the third paper, gave a method of calculating the percentages of the various compounds present in slags when the amount of oxide was given and also an interpretation of quaternary equilibrium. Illustrations were given of the mineral composition of blast-furnace slags and some applications of composition results were shown. Because of their relative ease of measurement, the viscosity-temperature relation for slags was selected as a factor which would be useful in correlating the physical properties of molten slags to furnace operation. With this in mind the viscosities of slags whose compositions are in that portion of the quaternary system, silica-alumina-lime-magnesia, in which blast-furnace slags occur, were thoroughly investigated.

Jan 1, 1932

By J. T. Norton, H. Blumenthal, S. J. Sindeband

The interstitial phases formed by the transition elements with carbon, nitrogen and boron constitute a unique class of substances which are of considerable technical interest because of their well developed metallic properties and their high hardness and melting points. They are also of interest from the point of view of structure. It was pointed out by Hagg1 some years ago that the principal factor determining these structures was the relative sizes of metal and metalloid atoms. He predicted that if the ratio of the radii of metalloid to metal atoms was less than 0.59, the metal atoms would be arranged in a close-packed fashion of relatively simple type. This prediction has been amply confirmed. It appears, however, that this specification applies most generally to those structures in which the metalloid atoms occupy isolated positions in the lattice and there is no tendency for strong binding between the metalloid atoms themselves. The series of borides of the type MeB2 formed from the transition elements of the fourth (Ti, Zr) and fifth (V, Cb, Ta) groups of the periodic table provide an opportunity to investigate this situation further. If one takes as a basis the radius of 0.87 A for the boron radius and the Goldschmidt values for the metal atoms in 12 coordination, then the radius ratio varies from 0.54 for zirconium to 0.64 for vanadium, which latter is considerably greater than Hagg's limit of 0.59. It was of interest, therefore, to see if these five elements would form borides of the MeB2 type and have simple isomorphous structures. When this investigation was initiated, relatively little information had been published on the structure of this group of borides. McKenna2 reported the preparation of ZrB2 by a carbon reduction process. Its structure was hexagonal and the approximate lattice constants were given as a = 3.15 A, c = 3.53 A. Ehrlich3 reported the structure of TiB2 as being of the C 32 type with a = 3.02, c = 3.21 and c/a = 1.06 A. Recently, Kiessling4 published the results on ZrB2, showing it to be one in which the metal atoms are arranged in a simple hexagonal lattice with the boron atoms in flat sheets, midway between the layers of metal atoms. The structure is C 32 type with a = 3.169, c = 3.530 and an axial ratio =1.11 A. He also states that CbB2 and TaB2 are isomorphous with ZrB2. Preparation of Borides The borides of titanium, zirconium, columbium and tantalum were made by the electrolysis of fused salt baths after the method described by Andrieux.5 The bath, totalling about 6500 g in each case had the following general composition: Metal Oxide + B2O3 + CaO + CaF2. The actual proportions of the ingredients were determined for each individual case. Although Andrieux reports the preparation of vanadium boride by the same electrolytic method, several attempts proved unsuccessful. However, it was possible to prepare VB2 by the carbon reduction method used by McKenna to produce ZrB2. The mixture consisted of V2O5 + 6B2O3 + 11C and the reduction was carried out in an induction heated graphite crucible. This method proved satisfactory for ZrB2 and TiB2 and undoubtedly the others could be made in the same way. The borides, which were all in the form of fine gray metallic crystals from the electrolytic bath or gray powders from the reduction process, were carefully separated from other constituents and analyzed chemically for metal and boron content. The densities of the boride powders were measured using a standard 10 cc pyenometer at 18°C and ethyl benzene proved to be the most satisfactory liquid for this purpose. X Ray Technique The boride crystals, as prepared, were too small for single crystal examination so that powder techniques were employed. Patterns of the finely ground borides were prepared, using the Norelco recording X ray spectrometer. The lines on these patterns were indexed with the aid of Hull-Davy charts and the approximate dimensions

Jan 1, 1950

By Pramod C. Thakur

Introduction Methane is contained under pressure within the fractures and adsorbed on the surface of the coal seams and adjacent strata. It is released into the mine atmosphere during mining of the seam creating explosive gas-air mixtures. Large volumes of air, sometimes as high as 20 tons of air for each ton of coal mined, are circulated constantly to dilute and carry away methane from coal mines. Removal of methane from solid coal, wherever high methane emissions occur, has been discussed by Spindler and Poundstone (1960) and Thakur and Davis (1977). Methane control in longwall gobs is much more complicated. As longwall mining progresses, the overburden continually subsides, and the immediate roof caves behind the roof supports. Even the underlying strata heave and open up communication channels feeding gas to the longwall gobs. The pressure of gas in the underlying and overlying strata is usually higher than the ambient air pressure in the mine. Thus the mine workings become natural pressure sinks, into which gas flows from the entire disturbed zone. Winter (1975) defines this zone as the "gas emission space". Depending on the number of gas-bearing zones in the gas emission space and their gas contents, the total methane emission from longwall gobs could vary from a few to more than one hundred cubic meters of gas per ton of mined coal. Hence the ventilation of longwall faces demands a large quantity of air. This ventilation need is further enhanced by high air losses specially on caving faces (with no stowing of the gobs). The old system of longwall ventilation, the 'U' pattern, where all the air was brought down one gate road and exited through the other gate road, loses large quantities of air through gobs giving a high methane concentration at the return end of the face. The 'Y' ventilation pattern where intake air is brought down both head and tail gate roads relieves the situation to some extent but, on most longwalls, some kind of methane control is still needed. With the onset of longwall mining in Europe several decades ago, the initial work on methane control on longwall has naturally been done there. The basic principle of methane control has always been, and still remains, some means of "bypassing methane from the gas emission space without letting it mix with the mine air". In most cases the bypassing mechanism is either a strategically located borehole or a roadway. A successful methane control program depends on the following basic premises: a. Determination of the geometry of the gas emission space and location of gas bearing horizons therein. b. Estimation of the rate of methane influx into the longwall gob. c. A scheme to bypass the gas in the most economic and efficient manner and thus prevent it from entering the mine atmosphere. In successful methane drainage programs a high proportion, usually between 50 and 70 percent, of the total gas emissions in a working district is removed before it can enter the mine airways. Advantages of methane drainage can be summarized as: 1. Generally reduced methane levels in the mine leading to increased safety and productivity. 2. Reduced air requirements and corresponding savings in ventilation horsepower. 3. Faster rate of advance for development headings and economy in the size of headings. 4. Possible use of mine gas as an additional source of fuel. The purpose of this paper is to briefly review the geometry of gas emission space and methane influx therein and discuss more successful European and U.S. longwall gob gas control techniques.

Jan 1, 1981

By D. F. Kaufman, H. R. Spedden, A. M. Gaudin

MANY studies of comminution have been made to ascertain the size distribution of the product and to evaluate the work of comminution in the light of the size distributions of the feed and product. Up to now, these studies have been essentially statistical in character, that is, a certain lot of feed was subjected to comminution in some specified way, and the aggregate product was fractionated into sizes, thereby losing all knowledge of individual relationship of feed to product pieces. Radioactive tracers offer a means to do something in this respect which could not be done before, namely, to follow the rupturing of some particular piece in its normal environment of other pieces. That is, it permits going beyond the usual statistical limitations of size distribution studies to what may be termed a personalized or individualized study. The purpose of this paper is to present some preliminary experiments conducted with this tool. The method employed was to mark radioactively some constituent of a feed. It is possible, of course, to consider the preparation of two lots of material of which one is radioactive and the other is not, and to blend the two ahead of the comminuting step; but to do so is open to the objection that the two preparations may not be identical. Therefore a technique has been chosen that removes this objection by merely taking out a size fraction of a comminution feed, rendering that fraction radioactive by exposure to a neutron flux, and then by returning it to Table I. Size Distribution of Offspring Albite Particles Originally 28/35 Mesh and in Admixture with Other Sizes After Grinding 2 min in a Steel Ball Mill Specific Activity ' Cumu- Corrected Distrl- latlve Size for Back- butlon In Distri- Fractlon ground, Weight, Product, button, of Product, cpm/gm g Pctb Pct Mesh (A). (W) (P) (ZP) + 28 0 56.0 0 100.1 28/35 62.6 54.0 24.8 75.3 35/48 62.8 59.4 27.7 47.6 48/65 41.1 53.0 16.2 31.4 65/100 29.6 45.7 10.2 21.2 100/150 23.7 37.0 6.6 14.6 150/200 23.3 25.1 4.4 10.2 200/270 20.1 19.0 2.9 7.3 270/400 17.8 21.2 2.9 4.4 -400 22.9 25.2 4.4 — 100.1 a These activity determinations were made in rapid succession in the order given. The specific activity (Ao) of the active 28/35 mesh fraction of the feed was measured at the beginning, after the measurement on the 65/100 mesh size fraction of the product, and; The end. The decay-corrected activities at those times were 246.7, 241.0. and 236.9 cpm per gm. The weight (W0) of the active 28/35 mesh fraction in the feed was 55.0. b Example of calculation for P in the 65/100 mesh oroduct frac- A W tion; A = 29.6, W = 45.7, Ao = 242.7, Wo = 55.0: P = — x — Ao Wo = 0.102 = 10.2 pet. the remainder of the charge for the comminution experiment. A relatively simple procedure was developed by which albite, containing sodium, was activated in the M.I.T. cyclotron. The cyclotron makes highspeed deuterons which impinge on a beryllium target, thereby producing a concentrated neutron flux. The mineral was exposed to this flux for 2 hr. This treatment changed enough of the sodium to sodium 24 (14.8 hr half-life, 1.4 mev ß) as to make detection and measurement easy. The nuclear reactions taking place were: 11Na23 (n,?) 11Na24 (irradiation) 11Na24 ß,?,? 12Mg24 (decay) The detailed technique of the experimentation was as follows: 40 kg of hand-sorted, lump albite were crushed to pass 10 mesh. After careful mixing of the lot, a screen analysis was made. The whole lot of material was fractionated on standard Tyler screens from 14 down to 200 mesh. Samples for experiments were compounded from these fractions in accordance with the screen analysis. When it was desired to make an experiment in which, for example, the 28/35 mesh size fraction was to be studied, the blend of size fractions was made as indicated above, except that the 28/35 mesh size fraction was added only after irradiation in the cyclotron. The blended charge containing the activated albite was ground for 2 min in a laboratory ball mill with a steel ball charge of controlled size distribution. The ground product was carefully sized on a set of Tyler screens in a Ro-tap. Each size was analyzed for radioactivity by the use of an end-window Geiger-Mueller counter and standard scaling circuit. This analysis was carried out in detail as follows: a 20-g sample was placed in a Petri dish, packed carefully to obtain reproducible geometric distribution with reference to the Geiger-Mueller tube, and the activity was counted for a 2-min period. Several determinations of the activity of the active size fraction in the feed were made at various times to establish the decay in activity with time. Linear interpolation was used to evaluate the activity that the active size fraction in the feed would have had at any given instant. The ratio of the observed activity in a size fraction of the product to the activity that the active size fraction in the feed would have had at the same time gives the fraction in the product size that came from the irradiated size in the feed. The general formula for finding the distribution, P, of a specific individual size fraction in the feed

Jan 1, 1952

PRESIDENT WILLIAM L. SAUNDERS,1 NEW YORK, N. Y. PAST PRESIDENTS CHARLES F. RAND,1 NEW York , N. Y. BENJAMIN B. THAYER,2 . NEW YORK, N. Y. FIRST VICE-PRESIDENT PHILIP N. MOORE,1 ST. Louis, Mo. TREASURER GEORGE C. STONE,1 NEW YORK, N.Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW York, N. Y.

Jan 4, 1915

By J. R. Elenbaas, J. A. Vary, D. L. Katz

The development of gas fields, oil fields and aquifers for storing natural gas is treated from two main vieu.-points: (I) the volumetric storage capacity for gas in a given situation and (2) the prediction of the number of wells required for the delivery of gas. Other experiences in the design and operation of storagc fields are incluclerl INTRODUC TION Storage of natural gas in underground reservoirs near the terminus of long distance pipelines has been the prime factor in opening the space heating market to the natural gas industry. Storagc has permitted a major. increase in both the load and the load factor of pipe-lines; some are now operating at steady load throughout the year. Thus, underground storage has been responsible for the rapid increase in demand for natural gas in recent years. Three types of reservoirs have been used for gas storage: natural gas reservoirs, oil reservoirs, and waterbearing sands or aquifers. This paper presents the factors to be considered when developing gas storage reservoirs of these three categories. There are two prime considerations tor any storage reservoir: (1) the volume of gas which a given reservoir will store advantageously and (2) the number 01 wells needed to provide the required peak deliverability. These two problems will be considered for the three types of reservoirs just noted STORAGE IN PARTIALLY DEPLETED GAS FIELDS Early storage operations consisted of replenishing the natural gas in a depleted gas field situated adjacent to the market. Today, newly discovered fields near the market may be considered for storage, and this discussion applies equally to both types of reservoirs. For reservoirs originally containing gas or oil, the question of the impermeability of the cap rock nor-mally does not arise. However, such fields are likely to have many wells drilled either to or through the reservoir under consideration. Positive assurance must be obtained that such wells are or can be made mechanically tight. Corroded casings may need to be lined or permanently plugged. Abandoned wells should bc reopened and properly cemented. The volumetric capacity for gas storage depends upon space available in the porous rock as well as pressure and temperature of the gas in the reservoir. The production-pressure decline data on partially depleted gas reservoirs without water drive permit calculation of the reservoir space for gas. Isopachous maps of sand volume and porosity data for the reservoir rock provide an alternate method of calculating the pore volume for water-drive reservoirs. The pressure range selected for the storage cycle depends upon ()) the safe upper limit of pressure. 2) the flow capacity of wells and (3) compression requirements when injecting gas into the reservoir or delivering to market. Normally, gas and oil fields have pressures at discovery in the range of 0.43 to 0.52 psi/ft of depth. Pressures of around 1.0 to 1.2 psi/ft of depth appear to lift the overburden1-3 and invite uncontrolled movement of fluids in the porous rock. Some top pressure is normally selected for a storage reservoir ranging from below discovery pressure for deeper reservoirs to 0.65 psi/ft of depth for shallower reservoirs. Pressures to 0.66 psi/ft have been experienced without difficulty. The lower pressure limit is set by water intrusion accompanying low pressures, reduced flow capacity for wells at lower pressures and compression requirements. Depletion-type gas reservoirs often encounter water problems in the later stages of gas production. Such water intrusion may be due to movement from the surrounding aquifer. Accordingly, displacement of this water back into the aquifer by gas pressure and subsequent surges of water corresponding to the gas storage pressure cycle must be considered. Storage fields often produce in four months a volume of gas equal to its initial content. Rapid decreases in reservoir pressure occur, such as 20 psi/day. Accordingly, closed-in pressure observation wells which reflect the pressure in the bulk of the reservoir are required for following the operation of the reservoir. It has been found that a plot of observation wellhead pressures against gas content, Fig. 1, is very useful in observing operation of the field, checking the inventory and predicting future behavior. The plot is based on a given quantity of base or cushion gas in place. The injection and withdrawal curves may spread depending upon the homogeneity of the reservoir rock. permeability of the rock, well spacing and flow rates.

By John T. Norton, V.G. Mooradian

The diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distortion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-torted lattice. On the other hand, it may be that the cold-working causes an increase in surface of contact between the two metals through fragmentation or provides a more intimate contact that is necessary for diffusion. If it is true that lattice distortion is an important factor in diffusion, it seems as if there should be some particular relation between

Jan 1, 1935

By V. G. Mooradian, John T. Norton

The diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distortion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-torted lattice. On the other hand, it may be that the cold-working causes an increase in surface of contact between the two metals through fragmentation or provides a more intimate contact that is necessary for diffusion. If it is true that lattice distortion is an important factor in diffusion, it seems as if there should be some particular relation between

Jan 1, 1935

By Charles Stuart

A PAPER on this subject can cover but a limited range. A thorough visualization of the subject would contemplate a comparative analysis of haulage machines and batteries of various types; the relationship of the storage-battery locomotive to other types of mine haulage should be considered and limiting factors in each case should be carefully developed. This paper will briefly deal with these factors. So far as the writer has been able to determine, the first storage-battery locomotives for mine haulage were manufactured in 1897 or 1898 and were tried out in the Pocahontas coal field, but they were not sufficiently satisfactory to justify their continued use. Battery explosions were frequent and caused serious damage to the wiring, electrical equipment, and the clothing and bodies of the motormen. Sulfuric acid was used as the electrolyte. Experiments were then conducted with locomotives bearing reels of flexible cable through which connection between the motors of the locomotive and the trolley wire was maintained. At first, these reels were turned by hand. Later, the reels were revolved by contact with the wheels of the locomotive, being raised out of contact with the wheels, by a lever, when necessary. About 1902, the plan of operating the reel, by chain and sprocket wheels, from one of the locomotive axles, as is still the practice, was devised. The popular floating motor-driven reel had its inception in the Pocahontas fields prior to 1906. The maximum radius of operation of the reel-type locomotive is about 500 ft. (150 m.) from point of connection with trolley wire. This is ample for room work and certain entry work, but the need for a machine that would operate entirely independently of the trolley wire was so great that, with the development of the storage battery, renewed efforts were made to manufacture a successful storage-battery locomotive. About 1908, the gasoline locomotive was introduced. In spite of many objections to this type of machine for such work, the fact that hun¬dreds of these machines were purchased was proof of the need for a machine operating independently of the trolley.

Jan 1, 1922

By R. B. Falk, F. E. Luborsky

Small iron particles in mercury pow by diffusion of iron atoms through the mercury. Iron particles, with diameters about 200Å, have been stopped from gvowing in size, even up to the boiling point of mercury, by the addition of a third metal. The metal additives were classified according to whether they produced 1) negligible inhibition, 2) some inhibition, or 3) marked inhibition of the growth rate. Metal additives which resulted in a marked inhibition of iron-particle growth form a stable monolayer on the iron particles. Only those metals which may form compounds with iron showed this pronounced effect. The one exception was manganese. Metal additives which resulted in no inhibition of growth, showed no evidence for adsorption and could not form compounds with iron. None of the added metals, even those which strongly inhibited particle gvowth and thus had adsorbed on the particle surface, actually formed any compounds with iron at room temperature at the concentrations required for complete inhibition of growth. ThE stabilization of the size and shape of metallic particles dispersed in liquid metals has important technological implications in "homogeneous" nuclear reactor systems and in elongated particle magnets and is directly related to the problem of corrosion by liquid metals. Growth in these par-ticulate systems may occur by diffusion of atoms from surfaces of high energy, corresponding to a small radius of curvature, to surfaces of low energy or large radius of curvature. Thus, small particles dissolve and large particles grow to increase the average diameter of the particles. reenwood' has analyzed this diffusional growth of a system of particles containing a distribution of sizes and has obtained reasonable agreement with data on the growth of uranium particles in liquid sodium and UPb3 particles in liquid lead. Greenwood concluded from his analysis that the chief factors promoting stability of dispersed particles growing by a diffusion mechanism are large mean radius, high density, and low molecular weight with low values of the solute diffusion coefficient, the solubility, and the interfacial tension. In the case of elongated particle magnets the system of interest is that of iron particles dis- persed in mercury. Previous work,2 concerned with "spherical" particles in mercury, has indicated a diffusional growth mechanism similar to that discussed by Greenwood. It has also been shown3'4 that the addition of certain metals to Fe-Hg dispersions results in the formation of a monatomic layer of adsorbed atoms on the iron particles. In this paper we will show that this adsorbed layer provides the decrease in the iron-atom flux through the mercury necessary for size stabilization. The general features of the stabilization of the iron particles in mercury through the formation of this "coating", with many different metals, will be described. EXPERIMENTAL RESULTS Iron particles in mercury were prepared by elec-trodeposition,2, 4 and measurements2, 4 of coercive force HCi) and saturation induction (Is) were used to follow changes in size and composition during thermal aging in the mercury in the presence of relatively small amounts of an added metal. In Fig. 1 is plotted the aging behavior of spherical particle samples in the presence of some of the added metals to be discussed. The iron particles have an initial average diameter of 180Å. Each sample was aged for 20 min at each temperature in succession in the presence of a twofold to threefold excess of added metal over that required to form a monolayer on the iron particles. These are the same samples used previously3 to study the adsorp-

Jan 1, 1965

By James J. Wise

INTRODUCTION One basic design feature utilized in all caving and sublevel stoping techniques is the drawpoint. These draw- points may be located on sublevels when using sublevel caving methods, or may be located at the floor pillar when using block caving, sublevel stoping, or vertical crater retreat methods. How the drawpoint is designed and developed, how the ore is withdrawn from it, and how the ore is hauled to the shaft or portal encompasses the loading and hauling function. Historically, predominate loading and hauling equipment for caving and sublevel stoping has been scraper slushes, air powered overshot loaders, and rail mounted train haulage. All of this equipment has two common constraints. 1. The equipment locked into specific work sites and is not easily shifted to another work site. This constraint can often lead to low utilization and low productivity of the equipment. 2. The equipment is designed to work in the horizontal plane, which requires that the various horizontally-oriented working levels be connected by vertical raises. Vertical development by means of raises is not only increasingly expensive, but also is not well adapted to movement of large equipment into the s topes. In the last 20 years, two revolutionary labor saving concepts have become common in caving and sublevel stoping. 1. Long-hole drilling, which has mechanized the development of the drawpoint extraction structures as well as the actual stoping and undercutting. 2. Vertical access by means of trackless ramps between levels, and the consequent use of rubber-tired vehicles not only for loading and hauling ore, but also for the rapid movement of men, material, and equipment into the stopes. The introduction of trackless mining systems for loading and hauling has not been easy. Mine planners have had to re-orient their thinking to the larger operating space required by trackless equipment. Larger access drifts have necessitated reconsideration of mine layouts to insure proper ground support. Spiral ramp developments were often laid out on slopes steeper than the equipment could negotiate economically. Mine operators had to accept the added responsibility of roadway maintenance, water removal, increased ventilation, and more technical mechanical maintenance. As the mine operators enthusiastically embraced the superior productivity of trackless mining systems, they some- times disregarded opportunities to combine the older types of equipment with trackless vehicles to maximize productivity at lowest cost. In order to gain a proper perspective on this problem, it is necessary to review the various techniques of loading and hauling and to become more aware of the advantages or disadvantages that each system or combination contributes. LOADING Loading consists of two functions, (1) primary loading from a drawpoint and (2) secondary loading into long- haul system, a truck, train, or possibly a belt conveyor. Mine planners have four basic loading systems available to fit various operating conditions. These are, (1) gravity, (2) scrapers, (3) rail-mounted loaders, and (4) trackless loaders. Each system can produce optimum results under specific conditions. Gravity Loading Gravity loading is probably the oldest system in general use today.

Jan 1, 1981

By R. J. Watson

IN an earlier paper, Ehrenburg and Watson1 published the develop-ment for a potential function by which it is possible to obtain the electric potential at points on the surface of the ground when a current I passes between two electrodes and the subsoil is composed of parallel, homo-geneous layers. In view of the continued interest in the resistivity method of electrical prospecting, the author has considered it desirable to publish the results of a number of theoretical studies making use of this potential function, and also the results of a considerable number of tests with models designed to show the soundness of the mathematical theory. It is hoped that these results will prove how erroneous the various empirical rules for depth determination may be. It has always seemed puzzling to the author that one can find, in papers published comparatively recently, statements upholding empirical rules for depth determination, and attributing most of the irregularities of resistivity curves to vertical discontinuities in resistivity in the subsoil. It would indeed be fortunate for the geophysical investigator if such a simple rule held. However, numerous investigators have proved both theoretically and by the success of their field work that such a rule does not hold, even by a" rough approximation" in many cases. On the other hand, as is shown in the development to follow; if the underground conditions are favorable it is possible for such empirical rules to give a satisfactory depth determination. Authors should be more careful about making such sweeping state-ments about the accuracy of these empirical rules because the relative simplicity of the field work places the method in the hands of any inter-ested experimenter, and he is likely to become completely disgusted with the method after he has made several obviously wrong interpretations by empirical rules.

Jan 1, 1934

By L. A. Rapoport, W. J. Leas, C. W. Carpenter

A program of scaled flow model experiments has been undertaken to study the performance of five-spot water floods. The modeling procedures are discussed and the construction and operation of the flow models are described. The tests were specifically designed to investigate the effects of injection rate and of oil-to-water viscosity ratio on oil recovery. The areal sweep of five-spot water floods was also studied, and direct comparisons between five-spot and linear flooding behavior have been established to permir better utilizatfon of core analysis results for purposes of field waterflood evaluations. INTRODUCTION For a long time reservoir engineering procedures have been confined to the consideration of idealized, one-dimensional or linear systems.11* However, direct application of the linear waterflood mechanism to the evaluation of actual field performance is justifiable only for the purposes of rough approximation. To obtain a realistic analysis of field behavior, it is necessary to account for reservoir geometry and well distribution, and to take into consideration the configuration of the flow of fluids between injection and producing wells. In the past it has been attempted to account for the complex nature of the fluid movement in the reservoir by associating each well pattern with a certain "sweep-efficiency constant", e.g., a sweep efficiency of 72 per cent for the conventional five-spot pattern.' More recently, methods of waterflood evaluation have been improved by the introduction of variable sweep-efficiency factors, defining the areal coverage as a function of cumulative water injection and viscosity or "mobility" ' ratio.""' These variable sweep-efficiency factors, derived from miscible fluid displacement experiments, require the assumption of piston-like displacement of oil by water. This implies that only one fluid, either oil or water, is moving at any one point of the reservoir ht any moment. Such an assumption, however, is incompatible with the bulk of the experimental evidence and also theoretical considerations which indicate that usually in the area invaded by water, both oil and water are flowing in varying proportions, in accordance with the relative permeability characteristics of the porous medium. Another recent approach toward the evaluation of five-spot flooding behavior involves correlations of the areal sweep efficiency (observed in immiscible fluid experiments) with a "mobility ratio," based on the consideration of the "average" relative permeability to the displacing fluid. Combination of these correlations with a modification of the Buckley-Leverett frontal-drive equation leads to a computational procedure for predicting the recovery performance of areal water floods. While of considerable interest, this approach has no complete theoretical justification and, therefore, does not entirely clarify the features of five-spot water floods. Rigorous, theoretical treatment of waterflood behavior in two- or three-dimensional systems as encountered in the reservoir, including proper consideration of relative permeability and capillary-pressure functions, is as yet beyond the scope of analytical or computational methods. The, behavior of such water floods can, however, be studied by means of scaled flow model ekperiments, which is the approach followed in these investigations. The flow model experiments described in this paper simulate a uniform, horizontal formation of constant thickness with fully penetrating wells. The system under consideration is entirely liquid saturated and not influenced by compressibility effects, which is representative of the situation achieved after gas fill-up under practical conditions. Gravity segregation effects are assumed to be negligible, which implies a relatively thin reservoir formation and/or low vertical permeability. THEORETICAL CONSIDERATIONS For a flow system of uniform thickness with no appreciable effects of gravity segregation, the analysis of water-oil displacement can be confined to a two-dimensional treatment based on the consideration of a "slice" of unit thickness. Referring to previously established derivations," the displacement of oil by water in such a system can be described by the following, dimen-sionless equations:

By Albert Hoskinson

PROGRESS on the earth depends to a large extent upon the rapid inter-change of ideas and commodities between the various nations of the world. The smooth flow of commerce, by which these ideas and com-modities move, is accelerated by accurate and complete maps of the various land and water areas of the earth, The production of accurate maps depends upon a complete knowledge of the figure and dimensions of the object to be charted, therefore a knowledge of the shape of the earth is a prime necessity for accurate charting purposes. Gravity observa-tions were first undertaken to aid in determining the shape of the earth so that the geodetic surveys of its land and water areas might be more accurately connected to form an undistorted map. A large part of the earth's surface is water and it is therefore necessary to get gravity values at sea as well as on land before a complete and accurate figure of the earth can be determined. Dr. F. A. Vening Meinesz, of Holland, was the first scientist to perfect a pendulum instrument that would accurately measure gravity at sea. He had previously developed a multiple pendulum apparatus for measur-ing gravity upon swampy and unstable land areas in Holland and it was therefore quite natural that he should adapt the instrument to give accurate results upon a still more unstable support, the surface of the sea. His instrument as perfected gives satisfactory results when mounted in gimbals on any vessel where the roll and pitch are not more than about 5° and where the vibrations from rotating machinery and wave action are not large enough to cause the pendulums to shift on the knife-edges. This degree of stability can be obtained on surface craft only in protected waters or on very calm days. Therefore, Dr. Meinesz mounted his instrument in a. submarine so that he could submerge below the disturbed surface waters and get the desired stability in nearly any kind of weather by simply diving to greater depths. Most of the gravity-at-sea work has been done with a Meinesz instrument and a very large number of the observations have been made by Dr. Meinesz himself. He has occupied nearly 1000 sea stations and probably has traveled as many miles by

Jan 1, 1938

By L. S. Darken

In the study of reactions occurring in liquid iron, alone or in contact with a liquid oxide or slag phase, it has been found that the experimental data over a limited range of concentration can in some cases be represented satisfactorily by the simple equilibrium expression where (P) denotes the concentration of a product and (R) the concentration of a reactant in the reaction r1R1 + r2R2 + • • • D P lP1 + P 2P2 + • • • Some of the reactions for which it holds are listed in Table 1. For others, however, the simple equation apparently does not hold. This has been attributed to an improper method of expressing concentration (for instance, weight per cent instead of mol fraction); or it has been supposed that the solutions are not ideal in the sense that the activity of a component is not proportional to its true mol fraction. But it may be that the problem has been oversimplified by neglecting some molecular species actually present; that is, by considering only the ostensible simple components and thus leaving out of account possible compound formation. It is the purpose of the present paper to point out how, in a group of related cases, a reasonable consistent assumption relative to the presence of a compound makes it possible to express the experimental data satisfactorily by the simple equilibrium expression when this compound is taken into account, and to bring into harmony data referring to different reactions in liquid iron. There are several a priori reasons for believing that solutions in liquid iron should not deviate far from ideality, provided that the concentration of solute is not too great and is expressed in proper terms. The factors that commonly lead to nonideality in systems at ordinary temperature— as ionization or the occurrence of polar and nonpolar molecules—are presumably less effective in inetal and in slag systems at high temperature. Again, the type of equation commonly used to express the value of

Jan 1, 1940

By L. S. Darken

In the study of reactions occurring in liquid iron, alone or in contact with a liquid oxide or slag phase, it has been found that the experimental data over a limited range of concentration can in some cases be represented satisfactorily by the simple equilibrium expression where (P) denotes the concentration of a product and (R) the concentration of a reactant in the reaction r1R1 + r2R2 + • • • D P lP1 + P 2P2 + • • • Some of the reactions for which it holds are listed in Table 1. For others, however, the simple equation apparently does not hold. This has been attributed to an improper method of expressing concentration (for instance, weight per cent instead of mol fraction); or it has been supposed that the solutions are not ideal in the sense that the activity of a component is not proportional to its true mol fraction. But it may be that the problem has been oversimplified by neglecting some molecular species actually present; that is, by considering only the ostensible simple components and thus leaving out of account possible compound formation. It is the purpose of the present paper to point out how, in a group of related cases, a reasonable consistent assumption relative to the presence of a compound makes it possible to express the experimental data satisfactorily by the simple equilibrium expression when this compound is taken into account, and to bring into harmony data referring to different reactions in liquid iron. There are several a priori reasons for believing that solutions in liquid iron should not deviate far from ideality, provided that the concentration of solute is not too great and is expressed in proper terms. The factors that commonly lead to nonideality in systems at ordinary temperature— as ionization or the occurrence of polar and nonpolar molecules—are presumably less effective in inetal and in slag systems at high temperature. Again, the type of equation commonly used to express the value of

Jan 1, 1940

By Edgar L. Collis

NO industry or group of industries is more deeply interested in the influence exerted by atmospheric dust than that concerned with the getting of coal and of metalliferous ores. The coal miner in the past has mainly been interested on account of the part played by coal dust in the occurrence of explosions; but investigation is revealing that coal miners experience, at least on certain coal fields, unduly high mortality ascribed to lung diseases, some part of which may reasonably be attributed to dust inhalation, and that a small group of men employed in sinking shafts and driving roads through sandstone rocks experience troubles identical with those that afflict many metalliferous miners. Coal Mining The Registrar General for England and Wales issues information every 10 years concerning the mortality experienced in various industries. The records dealing with coal mining are of particular interest, since they are given separately for each of the largest fields. When examined they exhibit the coal miner with a favorable death rate on the whole when compared with all other occupied males; but they reveal great differences on the different fields; thus the Lancashire miner in 1900-2 had a comparative mortality from all causes of 1006 as against a figure of 675 for the Nottinghamshire and Derbyshire miners, and in 1910-12 of 941 as against 570 for Nottinghamshire. When mortalities due to four only of the great causes of death are subtracted from the total the differences are greatly reduced; these four causes are phthisis, pneumonia, bronchitis and accidents. Thus for 1910-12 more than one-half of the mortality in Lancashire, 478 out of 941, is so accounted for, but less than one-third of the mortality in Nottinghamshire, 184 out of 570; the latter fraction compares with that for all males, 293 out of 790. Exactly why the accident mortality varies thus with those for the lung diseases has not been determined; the fact, however, points to an interesting association between health and so-called "accidental" occurrences.

Jan 1, 1927