Search Documents

By A. J. Lyon

The stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening, which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging—heating in a temperature range below 170" C. (340" F.)—will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1929

By H. H. Lowry

SCIENCE attracts the attention and interest of an individual or an industry in general only in proportion to the apparent direct application to its immediate welfare or benefit. Engineering accomplishments, as applied science, therefore receive more recognition than the scientific discoveries on which they are based. Even self-evident truth needs endless repetition before recognition: engineering as applied science cannot advance beyond the science on which it is founded. Scientific research, and discovery, is sometimes forced by the limitations recognized by those active in its development for the use of society and industry and sometimes results from an apparently superficially illogical curiosity about natural phenomena. Research has received inadequate support except in industries born in the laboratory, the chemical and electrical industries, from which many lessons might well be drawn by their elder associates. The rapid growth of these industries has been largely due to close cooperation of scientists and engineers. Most rapid advance is made when the research worker and the engineer keep in close touch with each other's ideas and problems. Many of the developments of modern industry are based on dis-coveries buried for years in scientific journals because the "time was not ripe" at their discovery. The situation with regard to utilization of coal is quite the opposite. The fundamental facts in regard to the scientific aspects of the problem of developing the energy from coal are scarcely known. The engineer, without much scientific cooperation, has accom-plished much in increasing the number of kilowatt-hours per pound of coal from 0.31 in 1919 to 0.69 in 1934, in increasing the 1000 gross ton-miles of freight hauled from 6.1 to 8.3 per ton of coal in the same period, in fuel economy in production of coke, and in developing the production of motor fuel in Germany and England by hydrogenation of coal. This lack of scientific research on the utilization of our most important natural resource, coal, has been due undoubtedly in large part to the reluctance of investigators to study the interrelationships involved in, the complicated processes in which coal is used. These complexities are made

Jan 1, 1936

By L. A. Geoffrion, R. H. Perkins, J. C. Biery

Densities of cerium metal and several lour-melting binary cerium alloys were measured over the range 25° to 800°C. A rolumeter, using NaK as working fluid, was used to obtain the data. The cerium, Ce-Co, Ce-Ni, and Ce-Cu alloys all exhibited an increase in density on melting, while a Ce-Mn alloy expanded on melting. FOR the proper design of a nuclear reactor, the change in density of the fuel with temperature must be known. This is especially important in a system utilizing molten fuel, such as LAMPRE (Los Alamos Molten Plutonium Reactor Experiment), since a relatively large change in density usually occurs during the solid-liquid transition. The fuel for LAMPRE is a Pu-2.5 wt pct Fe alloy with a melting temperature of 410°C. However, limitations in reactor design with this fuel have led to consideration of other plutonium-containing alloys for use in future generations of this type of reactor. Several ternary alloys containing plutonium and cerium as two components have satisfactorily low melting points. The system that at the present time appears to be most acceptable is Pu-Ce-Co; it exhibits little change in melting temperature with wide variation in plutonium concentration. Other alloys that have received some consideration contain nickel, copper, and manganese as the third constituent. The proposed fuel alloys are difficult to handle experimentally in the 25" to 800°C temperature range since they oxidize readily, react with many solvents, and contain a poisonous fissionable material. In addition, in this temperature range the alloys pass through the solid-liquid transition. Several techniques are available for measuring the densities and volume coefficients of expansion of solids or liquids. However, the only apparatus that appears suitable for measuring expansion coefficients over this temperature range and through the phase transition is a volumeter. In a volumeter, the indicating medium must be essentially inert to and insoluble in the material being studied. It must also possess a low vapor pressure over the operating temperature range, and its coefficient of expansion must be accurately known. One material that is satisfactory in nearly all of these respects is the alloy Na-78 wt pct K, which melts at -10°C and has a vapor pressure of 860 mm Hg at 800°C. This relatively high vapor pressure at 800°C requires an overpressure of an inert gas to prevent boiling. While a volumeter is capable of determining accurately the volume coefficients of expansion of materials, it cannot be used for absolute density measurements. Therefore, a density determination at a known temperature must be coupled with the volumeter measurements to give all the desired data. The weight-loss technique using immersion in bromobenzene at room temperature proved to be satisfactory. The preliminary work that was done on this experimental program involved developing and calibrating the equipment, and measuring the densities and volume coefficients of expansion of cerium and some low-melting binary cerium alloys. The complications that are caused with the introduction of plutonium into the system were avoided until the equipment was proved to be satisfactory and until experience was gained in its operation. It is this first phase of the experimental work that is described in this report. DESCRIPTION OF EQUIPMENT AND OPERATING PROCEDURE The NaK volumeter is shown schematically in Fig. 1. Basically, the equipment consists of two weld-sealed stainless-steel containers of nearly identical volume. One container holds a tantalum crucible and the specimen being measured; the other contains a tantalum crucible and a tantalum specimen used as a control reference material. To avoid temperature gradients, the bombs are located in a copper block inside the furnace. Stainless-steel capillaries of equal length and volume connect each stainless-steel container to a glass viewing capillary. The stainless-steel containers, stainless-steel capillaries, and a portion of the glass capillaries are filled with NaK (22 wt pct Na-78 wt pct K). The NaK/gas interface in the glass capillary is viewed with a cathetometer which is accurate to *0.5 mm. The cathetometer readings are used to calculate the volume changes of the samples during a run. This volumeter is basically the same as that described by F. Knight in Plutonium 1960. 2 However, changes in equipment design and operating procedure were made to eliminate some major operating difficulties. These changes are summarized below. 1) In filling the manometer with NaK, gas was frequently entrained in the system. Evacuation of the system before filling failed to eliminate the en-

Jan 1, 1965

PRESIDENT WILLIAM L. SAUNDERS,1 NEW YORK, N. Y. PAST PRESIDENTS CHARLES F. RAND,1 NEW YORK, N. Y. BENJAMIN B. THAYER,3 NEW YORK, N. Y. FIRST VICE-PRESIDENT PHILIP N. MOORE,1 ST. Louis, Mo. TREASURER GEORGE C. STONE,1 NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 8, 1915

By Leonard B. Gulbransen, John R. Lewis, W. Martin Fassell, J. Hugh Hamilton

A simple reproducible method was developed for determining the ignition temperatures of magnesium and magnesium alloys and by this method magnesium and over 100 magnesium alloys were measured. The ignition temperature of magnesium was determined in O2-SO2, O2-N2 mixtures and in O2 from 0.166 to 10 atm pressure. The ignition temperature of magnesium is generally lowered by alloying and increased by an increase in oxygen pressure. WITH the expanded use of magnesium alloys in industry, ignition temperatures are of considerable importance, especially in heat treating and for service at elevated temperatures. Magnesium alloys exhibit a relatively slow linear oxidation rate up to temperatures near the melting point.' At some critical temperature the rate of oxidation becomes extremely rapid. This high rate of oxidation is accompanied by the emission of light and additional characteristics suggesting a flame. The literature concerning the ignition temperatures of magnesium and magnesium alloys is relatively incomplete and the values reported by various authors are not in agreement. The most probable reasons for this are: 1—The absence of a suitable definition of ignition, and 2—the need of a standardized method of determining the ignition temperatures of inflammable metals and alloys. The exact date of the discovery of the fact that magnesium will ignite and burn is unknown. It is likely that H. Davey encountered this property of the metal during its preparation in 1808. The first reference in the literature specifically on ignition of magnesium is by Lenze, Metz, and Rubens.' They investigated the inflammability of certain magnesium alloys. Brown3-' reported that magnesium ribbon will ignite in air at 507 °C by what was called the rising temperature method. Hartman, Nagy, and Brown" reported that magnesium powder ignites from 475" to 560°C depending on particle size. According to Guise, Mars, and Wilson prolonged heating in air at 427°C of common casting magnesium alloy causes it to ignite. Samples of magnesium alloys were placed directly in the flame of a torch by Carapella and Shaw.' These investigators obtained some evidence of melting prior to ignition. For commercial magnesium, they reported an ignition temperature of 650°C. Their values varied from 450" to 800°C for magnesium alloys. Willmore and Peterson" studied the effect of air velocity, humidity, rate of heating, and foreign metal contact on the ignition temperature of magnesium. They conclude that melting is not a prerequisite for ignition and that the conditions which influence ignition are complex and difficult to analyze. The only quantitative theoretical treatment of the ignition temperatures of magnesium and magnesium

Jan 1, 1952

By Robert E. Green, T. Hinton

Expressions are derived for tke orientation factors appearing in the Grana to -Lucke theory of dislocation damping, for fcc crystals. The factors are given as functions of the elastic constants, the direction cosines of the specimen axis, atld the direction cosines of the particle displacemeizts, for darnping due to dislocation motion on each of the twelve possible slip systems as ixell as lor simultaneous dislocation rnotion on all twelve systems. RECENTLY Green' has outlined the general procedure for calculation of the modes of wave propagation in a single crystal possessing a given crystallo-graphic orientation. In addition he has suggested how the results of such calculations along with calculations of the resolved shear-stress factors for slip enable the orientation-dependent factors (orientation factors) appearing in the Granato-Lucke theory of dislocation damping to be calculated. However, reen' assumed that the maximum stress on dislocations was in the direction of the particle displacement of the elastic wave giving rise to the dislocation damping. The present cal'culations show that this is an oversimplified approach appropriate only to special cases of high crystallographic symmetry. The exact calculation of stress on the dislocations can only be obtained by resolving the nine components of stress associated with the elastic wave into the appropriate slip direction and then summing. In this paper the general expressions for orientation factors are derived for fcc crystals in terms of the elastic constants, the direction cosines of the particle displacements, and the direction cosines of the specimen axis, bearing in mind the point mentioned above. Equations are presented which give the orientation factors for damping due to dislocation motion on each of the twelve possible slip systems as well as for simultaneous dislocation motion on all twelve systems arising from elastic-wave propagation. These orientation factors are appropriate to attenuation measurements made by the pulse-echo technique, where the elastic wave is a traveling wave. They will be compared with those for the case of a standing wave as derived by Granato and Lucke which are appropriate to measurements of internal friction by the resonance technique. The expressions for the orientation factors are compared with the five values given by insruch,' based on unpublished work of Granato and Liicke, for positions of highest symmetry in the stereographic triangle. The various equations derived for modes of wave propagation and orientation factors have been evaluated for the case of aluminum crystals at 1-deg intervals throughout the stereographic triangle. These results will be presented in the form of contour diagrams in a subsequent paper3 and their relevance to ultrasonic measurements discussed. ORIENTATION FACTORS The coordinate system used for the calculations is shown in Fig. 1 and all specimen axes are taken to lie in the shaded standard triangle. The twelve slip systems are indexed according to Table I. Following the suggestion of lers, we may define the orientation factor Ok in the Granato-Liicke theory5 by the equation

Jan 1, 1967

By H. E. Lee, P. C. Feddersen

Greenockite is the only known cadmium mineral of importance. It occurs rather universally, in minor concentrations, as a secondary mineral in sphalerite deposits. The world's cadmium output is obtained through the processing of metallurgical by-products, largely from the treatment of residues from electrolytic zinc, retort zinc and lithopone plants. These sources are supplemented by the processing of fumes from lead and copper smelting operations. The development of modern selective flotation practice in the decade 1920-1930, which permitted the economical mining of complex lead-zinc ores, resulted in significant increases in the quantities of cadmium entering lead smelting systems. Being closely related to zinc as to occurrence, properties and production, most detailed description of cadmium recovery methods are to be found recorded in connection with zinc metallurgy. Other than occasional articles pertaining to particular operational procedures, literature offers but little in the nature of a balanced survey of lead smelter cadmium recovery practices. While many of the basic operations described for the recovery of cadmium from zinc by-products are applicable to the treatment of lead plant products, the inherent problems involved differ widely. In general the cadmium content of related by-products from routine lead smelting operations is present in lower concentrations, exists in a less soluble state and is associated with both a greater quantity and a greater variety of detrimental impurities. To cope with these problems, lead smelter practices are found to follow the general outline: Preparatory Processing 1. Concentration operations 2. Sulphation operations Cadmium Plant Processing 1. Leaching operations 2. Purification operations 3. Sponge precipitation operations 4. Metal recovery operations 5. Refining and casting operations As in the case of related zinc plant operations, cadmium recovery practices at lead smelters are not standardized. They not only vary as to type, but also extent. Depending upon prevailing conditions, lead smelter cadmium operations range from simple concentration campaigns, for the purpose of sufficiently "up-grading" products for shipment elsewhere, to complete processing steps for the production of refined metal. Preparatory Processing The cadmium content of lead smelter receipts is low and, as a rule, proportionate to the zinc content; the usual range of cadmium contained being of the order of 0.01-0.05 pct. Were it not for the low boiling point of cadmium, such small concentrations would, no doubt, be lost in the large tonnages of slag, metal and other smelter end products. However, the ready volatility of cadmium and its compounds at prevailing lead smelting temperatures results in its concentration in fractional portions of fume collected. This collected fume comprises a circulating load within the smelter system. Thus, the cadmium content of blast furnace fume* increases with each successive circulation until an equilibrium value is reached when the sum of the cadmium losses, due to handling and in slag, waste gases and other end products, becomes equal to the intake as ore. With ore receipts averaging, say 0.03 pct cadmium, the concentration value obtainable, through fume circulation in a routine manner, approaches 10-12 pct. In such operations, cadmium concentrations in blast furnace fume of from 3-5 pct are readily .attainable. However, the concentration gain beyond this range, with each additional circulation, is progressively decreased as a result of mounting losses occurring through handling and in end products. Therefore, to avoid excessive cadmium loss and to enhance the ultimate concentration anttainable, it is customary practice to isolate blast furnace fume at some intermediate cadmium content for special concentration procedure. The most common type cadmium concentration "campaign" involves special smelting operations wherein a relatively high portion of blast furnace fume at 3—6 pct cadmium is incorporated into the sinter charge. This type practice is roughly illustrated by the diagram on p. 111. Cadmium fume collected from lead blast furnace operations is not amen-

Jan 1, 1950

By J. N. Hummel

THE methods of electrical prospecting, which employ contact electrodes to produce an electric field in the ground, furnish information concerning the constitution of the material beneath the surface, as indicated by the distortion of this artificially produced field and anomalies therein. To reveal the distortion of such field of known character, it is only necessary to measure qualitatively the direction of the field, using sensitive compensation methods. In such a case, the survey is relatively simple, and that is an important factor from a practical point of view, The distortion of the normal field thus determined permits an easy interpretation and gives approximate information as to the subsurface conditions, without the necessity of a thorough theoretical knowledge of the electrical field. The true field of application of the equipotential lines and search-coil methods, which are based on this principle of directional determination of the electrical field in the ground, is that of search for deposits of economic minerals for the mining industry, although they can also be used in solution of other problems; for example, in the determination of the strike of anisotropic beds. The distortion of the electric field as represented by the picture of equipotential lines or other measured curves is striking only when bodies having conductivities different from that of the country rock are embedded in the underground, or when the underground is anisotropic.

Jan 1, 1931

By G. H. Miller

With the recent advances which have been made in science and technology and the increased use of mathematics in this area, the question of the best mathematics courses for a mining engineer to take is of major importance. The question becomes even more difficult to answer due to the recent increase in the number of different mathematics courses in the last two decades offered by the mathematics departments. Therefore, the National Study of Mathematics Requirements for Scientists and Engineers (NSMRSE) was designed to provide some answers to these questions. Approximately 10,000 scientists and engineers were selected for the Study, These individuals were placed in two categories: (1) The Awards Group, recipients of national honors or awards and those recommended by the members of the Board of Advisors as having national and international reputations in their areas of specialization and (2) The Abstracts Group, persons exceptionally productive in their research, based on the number of journal articles listed in the last five years in the Engineering Index, Scientific and Technological Aerospace Reports, Chemical Abstracts, Biological Abstracts, and the Physics Abstracts. The NSMRSE Course Recommendation Form and the Instruction and Course Content Sheet were constructed with the aid of the Board of Advisors and other consultants. For the Study, 40 courses were selected by the mathematical consultants. In order to make sure that the basic content of the mathematics courses was the same for all respondents, a brief resume of each of the 40 courses was given. The NSMRSE Course Recommendation Form consisted of seven sections. These sections were as follows: Section 1, 38 different specializations; Section 2, orientation of work (applied through theoretical); Section 3, highest degree obtained; Section 4, place of employment (academic, nonacademic); Section 5, administrative capacity (administrative or nonadministrative); Section 6, age groups (five-year intervals). Section 7 contained the 40 courses which were to be marked according to five categories: (1) Course Length, 3 to 36 weeks; (2) Applied-Theoretical Orientation, a five-point scale; (3) Course Level, freshman through graduate; (4) Knowledge of Course; and (5) Use of Course Content in Work. The Analysis The report of the data is based on the replies received from 44 mining engineers. This group was part of the Awards and Abstracts Group for all engineers. The resume of the recommended courses is reported in quintiles (upper fifth to lower fifth), since recommendations of this kind are not precise. The results of the Study are based on recommendations of the most active research men in engineering in the U.S. today; therefore, the reader should realize that these course recommendations represent an upper bound of mathematics requirements for the Ph.D. in both undergraduate and graduate work. Conclusions and Recommendations 1) Mining engineering students who plan to be active research specialists should take all those courses which are "very highly recommended" (80-10070) and "highly recommended" (60-79.9%). Those courses in the upper two quintiles and recommended by most mining engineers are: first-year calculus, third-semester calculus, elementary differential equations, applied statistics, and machine computation. Courses of "moderate recommendation" (40-59.9%) are: vectors, intermediate ordinary differential equations, the first course in partial differential equations, elementary probability, and linear programming. 2) The great majority of mining engineers indicated that they prefer a course which is concerned primarily with applications. Only the standard courses such as first-year college mathematics, calculus, differential equations, and advanced calculus received a recommendation for 50% theory and 50% practice. Therefore, all mathematics courses given to mining engineers should contain many applications and little theory. Engineers in both the applied and the combination (ap-plied-theoretical) groups indicated a definite need for applications in all courses. 3) In general, recommendations were for mathematics courses to be given for short intervals of time such as 3, 6, or 12 weeks. Only the standard courses mentioned previously received the usual one-semester or one-year recommendation. Therefore, it is of value to combine several related courses into a one or two-semester course so that the mining engineering student could acquire important mathematical knowledge at an early date in order to prepare him for his research. 4) There was little use for the newer courses in modern mathematics such as the functional analysis sequence, the modern algebra sequence, and the group theory sequence. In addition, there were uniformly very low recommendations (0-19.9%) for multilinear algebra, complex variables, mathematical logic, special functions, integral equations, approximation theory, analytic mechanics, integral transforms, and geometric algebra. Therefore, these courses should be given a low priority. 5a) Comparisons among mining engineers with different backgrounds showed that the combination ap-plied-theoretical group recommended more mathematics than the applied group. 5b) There was little difference in recommendations between the administrative group and the nonadminis-trative group. 5c) Analysis of age groups showed that those in the lower age groups gave significantly higher recommendations to courses such as the first course in partial dif-

Jan 1, 1971

By P. A. Boeck

The thermal insulation of high-temperature equipment for industrial purposes is a subject that has not received from engineers and designers the attention its importance deserves. This may be attributed to a number of causes: In the first place, heat flow is a rather difficult factor to measure under the working conditions of an industrial furnace, and until the comparatively recent introduction into certain operations of the heat balance sheet, with a systematic attempt to account for the discrepancies in the totals, the various causes of heat losses and the reasons for their existence were not brought to light. Moreover, such rapid advancement and radical changes in the design of equipment, especially in metallurgical lines, have occurred that practice has apparently outdistanced the theory of design. In the modern tendency toward greatly increased size of units, effort has seemingly been made to utilize the heat of fuel gases without proper attention having been paid to conserving heat energy and confining it strictly to the points of maximum activity. The systematic study of the thermal properties of structural materials, which is being carried out by various government bureaus and also by a number of technical societies, is forming the basis for more intelligent and consistent work in the economically important subject of prevention of fuel waste. Advantages of Insulation It is not necessary in this practical and utilitarian age to enlarge upon the need of prevention of heat losses, but attention may advantageously be called to the other benefits derived simultaneously with the saving in fuel and the increase in thermal capacity of furnaces when properly insulated. In most industrial furnaces—which are here spoken of in the broadest sense, indicating general high-temperature equipment for any purpose and heated in any manner—the operations are generally carried on through a temperature range which has been found by practice to give the most ef-

Jan 1, 1916

By Frank Clemens Smith

The occurrence of the tellurides of gold and silver, even in small quantities, is so rare that their metallurgical treatment has engaged little attention. A residence of several months at one of the few mines in North America the product of which consists entirely of such ore, has led me to arrange a method for its economical treatment. The mine referred to is the Huronian, situated a few miles distant from Jackfish Lake, in Ontario, Canada. The plan proposed is for this peculiar case, and is put on record as possibly suggestive and helpful .in any similar instance, should it occur. Since freight-rates from the mine to the nearest railroad-point were extremely high, and for other economical reasons, the method proposed is modified by the use, as far as possible, of the machinery already at the mine, and is so arranged that bullion instead of concentrates would be obtained as a final product. The ore-vein at the Huronian mine varied in width from about 4 feet at the surface to 2 feet and less at the lowest level—125 feet —and dipped southeast about 88. The rock consisted, on both foot- and hanging-walls, of soft, green Huronian slates carrying much highly crystalline but barren pyrite. The ore carried an inconsiderable amount of galena with iron and copper pyrites, argentite, hessite, sylvanite (or petzite), and probably altaite, the telluride of lead. Near the surface the ore showed considerable native gold, but this disappeared with greater depth. Two complete analyses of minerals containing tellurium are here attached, as they establish the presence of two important compounds: I. Analysis of a mineral supposed at the mine to be sylvanite, but agreeing more closely in composition with petzite (Ag, Au)2 Te: Ag = 41.062 Au =23.691 Te =32.007 Pb = 0.071 SiO2= 0.097 Fe = trace 96.928

Jan 1, 1890

By Thomas MacFarlane

AMONG the industrial enterprises which have, from time to time, been undertaken in our Dominion, few have been more uniformly unsuccessful than those which have had for their object the develop ment of our mineral resources. These resources hare not been re garded as insignificant. On the contrary, it is supposed that we possess in our ore deposits something more than mere points of mineralogical interest. Some people are enthusiastic enough to be lieve that our mineral wealth will yet occasion the establishment in our backwoods of happy and industrious communities, causing, in fact, our wilderness to blossom as the rose. These enthusiasts do not shut their eyes to the serious obstacles which at every stage in terfere with the carrying out of mining enterprises in this country, and which tempt one to believe that no such enterprise can ever be conducted to a desirable end, but they entertain the conviction that as our capitalists, miners, and technologists reach the years of discretion, and handle our mines in an economical, vigorous, and judicious manner, and as our statesmen become alive to the necessity of fostering, without extremely protecting, our metallurgical indus tries, mines and furnaces will gradually prosper, and so develop as to become a tower of strength to our agricultural, manufacturing, and mercantile interests. The fact that our past experience does not generally justify such glowing anticipations makes one all the more anxious to put on record the history of a successful mine, such as the Silver Islet has, on the whole, been. My connection with its discovery and early development was a very intimate one, and I propose in this paper to sketch its history and character, and sum up the amount of silver it has so far yielded. An additional reason for the appearance of this paper is that the Transactions of the Institute contain only a few references to the Silver Islet Mine. Although this mine is reported successful, we have, of course, no guarantee that it will not fall a victim to the same influences which have

Jan 1, 1880

By A. E. Bellis

There is a wide difference of opinion among rifle experts in the matter of barrel steel, and the relative importance to the life of the barrel of the steel's composition, heat treatment, structure, and physical properties. In order to promote discussion, which it is hoped may' lead to the discovery of the source of some of the traditional beliefs on the subject, the results of some tests are presented here, with data on heat treating, physical tests, and erosion. The detailed metallographic study of this steel is given in another paper.l The conclusions from these tests should be capable of wider application than their direct bearing on the barrel-steel problem. The Government specifications for barrel steel for model 1903 rifle (Springfield) call for carbon 0.50 to 0.60 per cent., manganese 1.00 to 1.29 per cent., silicon under 0.25 per cent., sulfur under 0.06 per cent., phosphorus under 0.08 per cent. The minimum physical requirements are: Tensile strength, 110,000 lb. per sq. in. (7733 kg. per sq. cm.); yield point, 75,000 lb. per sq. in (5472 kg. per sq. cm.); elongation, 20 per cent.; reduction of area, 45 per cent. Material fulfilling these requirements gives practically no failures when proof-fired, with charge of 70,000 lb. per sq. in. pressure, which is 40 per cent. in excess of the service charge. The turning and drilling operations show up any seams or laps such as accidentally occur even in the best heats of open-hearth steel, so that faulty stock is practically all eliminated before proof-firing. These physical requirements are met either by rolling billets at a proper temperature down to the form of tapered barrel blanks or by heat treating bars that have been upset to cnlarge the breech section. The transformation temperature of this steel, on heating, is around 1350" F. (732' C.), varying somewhat with the composition and the rate of heating. The actual treatment of the barrel blanks, as carried out by different manufacturers, gives four kinds of barrels, which will be called A, B, C, and D, for convenience. A barrels result from heat treating upset blanks by quenching at

Jan 1, 1920

By W. A. Tiller

The conventional techniques1 for determining the liquidus and solidus surfaces of an alloy system containing more than two components are extremely tedious to use and do not provide a complete picture of the equilibrium relations between solid and liquid alloys. These techniques are unable to yield "tie-line" information concerning solid and liquid phase equilibrium, a very important parameter in the solidification description of the liquid alloy and a very necessary parameter in the preparation of "zone-levelled" alloy crystals. The tie-line in a polycomponent system is analogous to the partition coefficient, k, in a binary system, it gives the composition of the solid, Cs, in equilibrium with a liquid of composition CL. That is, CS = kCL, where CL = [CO, c1,...Cn] denotes the concentrations of the n + 1 constituents, and k = [ko, kb ,...kon] denotes the gross partition coefficient for the elements between the two phases; thus, k is the tie-line in this system. To provide complete information concerning the two-phase equilibrium in a polycomponent system it is necessary to know both the liquidus surface and the gross partition coefficient. From these two the solidus surface is obtainable. The conventional techniques are unable to provide this information in other than a binary system so we must look elsewhere. In recent years considerable insight has been gained into the correct description of the liquid-solid transformation, 2,3 and controlled solidification experiments may now be designed to both facilitate and enhance equilibrium diagram studies. In the present paper consideration is given to two methods for obtaining the liquidus surface and the tie-lines in polycomponent systems. The methods to be described below deal with the solidification of an n + 1 constituent liquid alloy of initial composition [co, Co ,...Con], where the superscripts refer to the elements present and the Oth element is considered as the solvent in which the n solutes are dissolved. The general assumptions made in the treatment are the following: (i) the solid and the liquid at their interface are in equilibrium during the growth of the solid phase, (ii) there is no diffusion in the solid phase, and (iii) the liquid phase is completely mixed and is therefore homogeneous in concentration. METHOD I In this section a general experimental method will be described which, in principle, is capable of giving an exact description of the liquidus surface and tie-lines. Consider the unidirectional solidification of the liquid alloy specimens L cm in length (freezing either horizontally or vertically). Allow the sample to be frozen very slowly from one end, as indicated in Fig. 1, with complete mixing in the liquid, and then analyze the solid bar to determine its chemical constitution as a function of position, x, along the bar. Let Fig. 2 represent a possible distribution of the ith constituent along the bar. At the point x' the concentration of the ith constituent is C1/5(x'), and the average concentration of the rest of the bar between x' and L is given by C:(X' - L) where [ A(x) c1s(x)dx c1/s(x'-L) = f A(x) dx x * and A(X) is the cross-sectional area at x. In a similar manner. all the Cf(x' - L) may be determined. Thus, the gross artition coefficient k for liquid of composition [Cs(x - L),...Cs(X' - L)] is given by -ko= CUs')/Cos(x' - L)" k0 = csn{x')/cs(x'- L) During the freezing of a charge of length L, the liquid composition may vary over a wide segment of the phase diagram and the gross partition coefficient over this segment of the phase diagram may be determined from one, bar. Fig. 3 illustrates the magnitude of Cs(g)/C,' as a function of the fraction g of the bar which has Solidified.2 We can see that the concentration in the bar will vary over a range of about 15 wt pct for C,' = 10 wt pct and k0 = 0.5. It appears that 4 or 5 specimens would be adequate to study a simple binary eutectic phase diagram.

Jan 1, 1960

By Fred Porter

Pollution problems from smelters may be unique in industry since the pollutants cover the wide range of SOx, particulates, carcinogens (arsenic), plus a number of heavy metals, the health implications of which are not clearly understood. In addition to this wide range of pollutants, many of the plants are extremely old; and fugitive emissions may, in fact, be the most significant air pollution problem. The Environmental Protection Agency, both in an in-house and contract effort, has assessed the quantity of pollutants emitted and evaluated the health impact. This paper will review the status of EPA's regulatory efforts in both new and existing smelters in light of these pollutant assessment studies.

Jan 1, 1976

Estimated Receipts Dues Arrears $ 3,500 00 Current 108,115 00 New Members - 11,937 00 In Advance 1,763 00 $125,315 00 Initiation Fees - 7,250 00 Initiation Fees-Additional if increased to $20 00 7,250 00 Sale of Transactions 3,000 00 Sale of Binding 7,092 00 Sale of Magazine 2,913 00 Sale of Pamphlets 370 00 Sale of Indexes and Emmons Vols 313 00 Sale of Pyrometry 900 00 Sale of Raymond Vol 100 00 Interest received on Bank Balance . 500 00 Interest received on Life Memberships 500 00 Advertising-Gross 27,000 00 Voluntary Subscriptions-Estimated 16,000 00 Income from James Douglas Fund 5,000 00 Total $203,503 00

Jan 1, 1923

By C. L. Horn

All the tunneling machines discussed in this chapter are Calweld machines. I have divided the machines designed for soft-to-medium formations into three groups, correlated with typical formations and estimated compressive strengths: 1) Running sand and silt requiring blade cutters. 2) Chalk and clay, requiring drag-type cutters, for compressive strengths ranging from 0 to 2000 psi. 3) Sandstones, hard clays, and limestones, requiring disk cutters, for compressive strengths ranging from 2000 to 20,000 psi. All of the soft-to-medium-formation machines are powered by electric hydraulic or diesel hydraulic pumps. The pumps in turn drive hydraulic motors for the torque reaction. The soft-to-medium-formation machines are enclosed in a 360º shield with a cutting shoe, a center portion of the shield housing the mechanical equipment, and a tail shield. Tunnel supports are usually required, and the supports are normally erected in the tail shield. Our first machine was built in 1963, and all but five of the machines illustrated in the figures with this chapter were built in 1966 and 1967. Some of the machines manufactured will be discussed in the following sections; specific features as development has progressed will be pointed out. HARD-ROCK MACHINE The Calweld hard-rock machine has been designed along basic and accepted principles for a hard-rock mechanical borer. The features of this machine are as follows: 1) Direct electric motor drive through a planetary gear reduction ring and pinion gear, and then to the cutting head through a hollow drive shaft.

Jan 1, 1970

By Bernard E. Fernow

About eight years ago a comprehensive study of American timbers was begun in the U. S. Division of Forestry with a twofold object. On the one hand, it was desired to deternliiie the working-qualities of our numerous economically important timbers, and to furnish reliable standards of strength. 011 the other hand, it was intended to get a clearer insight into the properties and behavior of wood in general, with a view of establishing more rational methods in its use, and to furnish data for physical inspectioil which would permit an intelligent application of the standards of strength, and place upon a rational foundation the so-called " factor of safety," which is at present a mere baseless guess. The first object, namely, the establishment of standards for any given species, requires a very large series of tests, since Wood is an exceedingly variable substance, so much so that in the same tree a variation of 50 per cent. in strength may be found; hence the greater need of rational data of inspection. So far, the insufficient appropriations and facilities at our disposal have permitted us to establish really reliable standards for five species of southern conifers only. These have been deduced from nearly 20,000 tests. Besides these, 10,000 other tests have furnished indicatious regarding some two dozen other species. This work is now entirely abandoned, waiting for more prosperous times. The study of wood in general, however, can be carried on with smaller means, and has this year yielded not only very interesting, but highly important results, which will soon be published in detail. It is the purpose of this paper to make to the Institute the

Jan 1, 1899

By E. N. Aqua, C. M. Owens

The microstructure in cold-rolled Zircaloy-4 sheet has been characterized by transmission electron microscopy and X-ray diffraction line-broadening techniques. The rate of work hardening is measured in terms of microstrains, particle sizes, micro hardness, the tensile yield strength. The tensile yield strength of Prestrained (less than 10 pet) Zircaloy-4 sheet is found to be a linear function of the square root of the dislocation density, us predicted by work-hardening theories. ZIRCALOY is one of the most important structural alloys for nuclear reactor applications.''2 In order to understand the effects of the nuclear environment on Zircaloy structural members, the preirradiation microstructure must be characterized. This report will describe the substructure existing in cold-rolled Zircaloy-4 sheet as observed by electron microscopy and by X-ray diffractometry. I) EXPERIMENTAL PROCEDURE Commercial Zircaloy-4 strip was cold-rolled and annealed in argon at 760°C for 1 hr. The annealed sheet was again cold-rolled to a maximum of 50 pct reduction in thickness with segments of the strip being retained after 2.5, 5, 10, and 20 pct reductions. One-inch-square portions were chemically polished (50 parts HNO3, 50 parts H2O, 10 parts HF) and mounted onto lucite blocks using double-sided tape to prevent bending during handling. Thin foils suitable for transmission electron microscopy were prepared from each of the sheet samples. The sheets were mechanically polished through 600-grit paper to a 3 to 4 mil thickness and were chemically polished by immersion for 1 to 2 min in a solution containing: 50 parts HNO3, 50 parts H2O, and 10 parts HF, and rinsed in distilled water. The final metallographic procedure was to electropolish for less than 10 sec with an electrolyte of 10 parts perchloric acid and 90 parts glacial acetic acid, at 20 v, at room temperature using stainless-steel point cathodes and a vigorous stirring action. These foils were examined in a Philips EM 200 electron microscope using a 100-kv accelerating voltage.

Jan 1, 1968

IN CHAPTER I it was shown that the approximate market value of the copper produced at the twelve big Porphyry mines from 1905 to 1931, inclusive, was $2,821,300,000. This represented the refined metal ready for shipment to the consumer. In addition, at least $50,000,000 worth of gold and silver had been produced, more than $30,000,000 coming from the Utah mine alone. Consequently, the revenues totaled about $2,871,300,000, as shown in Table 58. Society paid this sum for a given quantity of metal that it wanted for industrial use. Where did the money go? Who were the direct beneficiaries of the creation of this new wealth? These questions this chapter will answer in a general way. Because some necessary data are not available, an exact tabulation in detail can not be made, but Table 58 is believed to reflect with reasonable accuracy the disposition made of the aggregate income from the twelve operations. The word "operations" is used advisedly because the complexity of corporate relations precludes the possibility of picking out companies, as could be done if each enterprise were an independent entity such as Miami, for example. Some explanation of the table and some elaboration of the items under "Outgo" is desirable. In the first place, it is assumed that the sum of surplus current assets existing in various treasuries at the end of 1931 was substantially equivalent to the “new” money that actually was put into the enterprises as a group. Less than $20,000,000 in new capital was realized from securities sold by the Utah Copper Co., the remaining funds coming from earnings. In respect to some of the others, such as Chuquicamata, Inspiration, and Andes, the amount of new money was much greater. However, of the two items-total new capital invested and total current surpluses-the former

Jan 1, 1933