Search Documents

By R. A. Flinn, R. D. Pehlke, D. R. Glass, P. O. Hays

Knowledge of the depth of penetralion of an oxygen jet into the bath of the oxygen converter and of the correlation of penetration with driuing pressuve, lance heighl, and nozzle throat area is vital to the understanding of converter operation. If the penetration is too shallow, then severe and hazardous slopping takes place. On the other hand, if the jel penetrates entirely Lhvough lhe bath for an apprcciublc period of time, bottom damage occurs. In addilion to measurement of the penetralion of the jel, knou~ledge of the circulatory movement in the bath is also of interest in order to evaluale various theories oj-concerter operating behavior which have been published. In this investigation, experimental converters were buill of IOU- , 300-, and 4000-lb capacity. Four independent methods were used to determine penelralion: the onset of bottom marking, a nitrogen bubbler probe, observation througlt an optical syslew built into the oxygen lance, and direcl viewing of the jet issuing from the bottom of the vessel. Good correlation zuas obtained, and empirical relalions for pvedicling perletration were found. These relations were conjzrmed by bottom marking tests in 55- and 110-ton vessels. Within the operaling conditions employed in these tests, the depth to which a single oxygen jet penetrated zuas found lo vary according to the relatiorl ThE technical literature is replete with data concerning the successful use of the basic oxygen furnace or converter in steelmaking. Experimental data are lacking, however, on the vital factors of the depth of penetration of the jet into the bath and the induced circulation. Commercial operating conditions usually have been the result of cut and try experiments in lance manipulation until satisfactory results were obtained. There have been, however, two hotly argued opposing theories concerning desirable depth of penetration and these are exemplified by the Schwarz and Miles patents1,2 on one hand and the Suess patent3 on the other. The Schwarz patent teaches that the jet, issuing from the nozzle at supersonic speed, penetrates deeply "so that the reactions between the iron and the oxygen and between the oxygen and the rest of the smelting components take place in the center of the bath". Specific operating suggestions are given by Miles.2 By contrast, the Suess patent calls for surface Circulalion was investigated by lour methods: by direct observation in 200-lb open baths, by the use of graphite rudders in the 300- and 4000-lb converlers, by direct observalion through an oplical system in the lance, and by various models al room temperature. All were in excellent agreement and indicated that the motion of the bath ulas up at the center, radially outluavd at the surface, and down at the sides. Experi-ments in small and in commercial vessels indicate that it is essential to operate with a jet penetration of approximately 50 pct of the bath depth. Surface blowing results in low oxygen eficienty and in hazardous conditions which may render the process inopeuable. RejYactory dartzage al the bottom of the vessel is only encountered when the jet penetrates to the bottom, and this can be avoided by properly applying the penetration formula. The application of this en/pirical formula in commercial peraations is best when limited to combinations of lance size, pressure, and height which are typically encounteved in the use of a single-hole lance. blowing so that "...the oxygen jet does not penetrate deeply into the molten metal bath and is confined to an impingement area at the central portion of the bath surface". These references are given merely to illustrate the basic differences between the two schools of thought and to point out the need for measurement of penetration for the sake of the operator. For example, it is shown later that inefficient and even dangerous conditions can arise if improper blowing conditions are used. Differences are also evident between the two schools of thought as to the mixing, circulation, and agitation which is to be accomplished by the jet. The Schwarz patent states that "surface contact is not sufficient in most cases to bring about quick reaction, the same as the blowing of the gas over the bath surface or the mere blowing of the gas onto the bath surface". The patent goes on to call for active mixing. In contrast the claims of the Suess patent call for "discharging a stream of oxygen ... to an extent to avoid material agitation of the bath by the oxygen stream". In this patent the circulation is said to be downward in the center and up at the sides of the vessel. A number of investigators4-12 have explored penetration and circulation in transparent models. In general, it is agreed in these tests that the circulation is upward at the center (along the sides of the jet cavity),

Jan 1, 1968

By Edwin C. Barringer

IRON and steel scrap has again become page one news, as it was during the war. To many this is anomalous because the common concept is that the theaters of war are literally paved with scrap as the by-product of war damage and abandoned materiel. To an extent this is true, the bottleneck being the ferreting out and transportation of this scrap. While you as consumers of the electric-furnace grades of scrap-the premium grades-are concerned primarily in only one segment of the scrap market, I believe you ill be interested in a general discussion of the market with subsequent funneling down to your specialty.

Jan 1, 1947

By H. W. Graham

[ ] Even though we have a small audience, I am sure there are some here who are interested in sponge iron. It is a large subject, with a lot of economic interest, and one that will continue to grow in importance as the years go by and as the conditions that urge action in that direction increase. The authors have chosen to deal in this paper with one particular narrow phase of a long program of work by the Bureau of Mines. Before asking for any general discussion, I would myself like to ask Mr. Buehl if he would tell us just a little bit about the mechanism of discharge and the form in which the material was discharged; that is, when dolomite is added, what happens to the dolomite? R. C. Buehl (author's reply)-You are interested in the equipment that was used? H. W. GRAHAM-No, just the product. R. C. Buehl-The product was in granular form, of a shape very similar to that of the ore used. Using minus 10-mesh ore, the product is essentially minus 10-mesh, mixed with the coal and dolomite. It is then passed through a belt type of magnetic separator, which picks up the magnetic iron and allows the dolomite and coal to fall off. If the coal is sufficiently valuable, it can be separated from the dolomite and, provided the coal has a sufficiently low ash content, it can be reused. For instance, if a low-ash reducing agent like petroleum coke is used, it can be reused until all the carbon is consumed. H. W. Graham-That clears the point for me. I was not quite sure whether the experi-

Jan 1, 1947

By Walter H. Bruckner, George B. Clark

Since the end of World War 11 interest has been increasing in the use of shaped charges in the mining industry and in other industries using explosives for blasting purposes. Shaped charges employ the principle known as the "Munroe effect," which was discovered by Charles E. Munroe more than 50 years ago (in 1888). Details of their design have been explained elsewhere.1,2,3 Fig I shows the essential features of design of two types of shaped charges (with conical and hemispherical cavities) and a schematic sketch of their action upon detonation. The following discussion deals with the behavior of the metal in the cavity liners when they are subjected to intense Pressures exerted when the explosive charge is detonated. Among the conclusions reached in research on shaped explosive charges, the following have been established conceming cavity liners:1'2 I. The optimum wall thickness of a conical cavity liner is dependent upon the apex angle of the cone as well as On the base diameter of the charge. Acute apex angles require thinner walls for optimum perfonnance and more obtuse angles require thicker walls for the same base diameter. '. Cones were more effective in forming a penetrating jet when the walls were tapered; that is, the thickness of the wall of the cone increased from the apex down. 3. The physical and mechanical properties of metals have a marked effect upon their performance as cavity-liner material. Boiling point, ductility, malleability, ten-sile strength, and hardness are among the properties that influence the effectiveness of a metal used as a cavity liner. Lead, for example, makes a wide, flat crater in steel plates. Aluminum makes a deeper crater than lead, and an aluminum alloy having a high tensile strength makes a deeper hole, but slightly smaller in diameter. Cast iron makes a deep, narrow hole. These findings, together with the following analysis under Metallographic Survey of slug, offer solutions to many of the problems involved in solving the mechanism of the formation of Munroe jets. It has been fairly well established that cavity liners collapse in a manner similar to that indicated in Fig 2, Conical liners are known to collapse upon themselves while hemispherical liners are believed to turn inside out in the process of jet formation. The first has been definitely proved by recovery of collapsed portions of cones, while liners from partly detonated charges show that hemispheres may turn inside out. Fig 3 shows a sketch of a recovered slug from a 6-in. shaped charge using a 45" cone made of cast iron. (This size of charge drilled holes up to 3 ft in depth in solid granodiorite.)

Jan 1, 1949

By Brian W. Mackenzie

In this age of advancing technology, mining companies are confronted with increasing competitive forces. The depletion of high-grade deposits and the development of substitute materials are intensifying market competition. The accelerating activity of petroleum companies in mineral exploration is increasing competition for deposits. At the same time, the trend in government policy is towards a reduction in traditional mineral-industry incentives. To succeed, the mining company must respond to these changing economic conditions by developing a decision-making framework that can effectively contend with the new opportunities and constraints. What are the elements of such a decision-making framework?

Jan 1, 1970

By W. C. T. Yeh, T. G. Oakwood, A. A. Hendrickson, R. H. Hammar

The objective of the research is to determine whether solid-solution strengthening effects observed in dilute solutions of silver can be accounted for by the influence of the solute addition on the dislocation structure oj- the crystals. The additions of both tin and indium produced only small changes in the dislocation densities and arrangements in silver crystals. However, as found previously, small solute additions have large effects on the tensile properties; the inj-luence of the tin and indium additions on the temperature dependence of the flow stress and the easy-glide range is especially strong; It is concluded that the indirect strengthening effect of the solute due to variations in the dislocation density as proposed by Seeger is of minor importance and that solute atom-dislocation interactions are responsible for the observed strengthenirzg effects. The experimental results were combined with those of Rogausch to test the concenlvatiorz dependence of solute strengthening. Both the first and one-half power dependences of the critical resoleed shear stress on concentratiorz fail in very dilute solutions. THE objective of the research is to determine whether solid-solution strengthening effects observed in dilute solutions of silver can be accounted for, at least in part, by the influence of the solute addition on the dislocation structure of the crystals. It is recognized that the addition of solute atoms may influence the strength properties of a metal through both "direct" and "indirect" effects. The former refer to the strengthening mechanisms that result from the interaction of solute atoms with dislocations; in the latter case, the strengthening effects arise as a result of solute's influence on quantities such as dislocation density, dislocation arrangement, stacking-fault energy, diffusivities, the elastic constants, and so forth. It is clear that the correct interpretation of solid-solution strengthening phenomena cannot be given until the importance of indirect strengthening effects is properly evaluated. In the particular case of close-packed metal crystals, Seeger showed that solute strengthening effects in dilute solutions of copper and silver might be accounted for by an increase in dislocation density due to the addition of the solute. Seeger's argument was that the strengthening effects extrapolated from more concentrated solutions indicate that small concentrations of impurities raise the critical resolved shear stress much more than is predicted by a concentration-independent dislocation density. The above idea was a very reasonable one. The dislocation theories of work hardening of Taylor,2 Cot-trell, 3 Mott, 4 and seeger5 had already associated the increased flow stresses with increased dislocation densities in deformed metals; investigations of the dislocation structure of metal crystals had provided a logical basis for expecting an increased dislocation density in crystals containing impurities (see for example, Ref. 6). The numbers involved seem reasonable, too. It can be expected that the flow stress of the crystal would increase as the one-half power of the dislocation density.' Solute additions of 1 at. pct to metal crystals result in strength increases by factors in the range of three to ten. If one assumes that the strengths of the pure metal crystals are determined by their dislocation densities, then dislocation-density increases of one to two orders of magnitude as a result of solute addition would be required to account for the observed strengthening—not an unreasonable expectation. In addition to the effect of the solute addition on dislocation density, one might also anticipate important strengthening contributions to result from the solute's influence on the dislocation arrangement. Parker and washburns have reviewed a number of experimental evidences which show important strengthening effects due to the presence of subboundaries. Further, lattice strains due to impurity segregation would be expected to influence the distribution as well as the dislocation density of the as-grown crystal. As pointed out in the reviews of Chalmers,6 Elbaum,9 and winegard,lo micro segregation of impurities occurs at all interfaces of crystals in cellular growth; the impurity gradient results in lattice strains which can be reduced with the presence of dislocation arrays in the region of the impurity gradient. Hence, one would expect the presence of a solute to favor the formation of dislocation subgrain structures and that the subgrains would have an important influence on the strength of the crystal. The experimental observations that concern the possibility of an important strengthening contribution through the influence of the solute on the dislocation density or arrangement are not in agreement. Haasen has reviewed the observations of Meakin and Wils-dorf,12 Howie,13 and Bocek 36 and concluded that the solute's influence on dislocation density is not sufficient to account for strengthening effects in concentrated solutions but might, as seegerl suggested, make an important contribution in very dilute solutions. On the other hand, Hendrickson and Fine 14 concluded that changes in the dislocation density and dislocation width accounted for the solid-solution strengthening effects observed in silver-based aluminum solid solutions. Goss et a 1.I5 observed dislocation arrays in Ge-6 at. pct Si, Ge-0.2 at. pct Sn, and Ge-0.2 at. pct B crystals that were not observed in germanium crystals of

Jan 1, 1968

By W. N. Best

(San Francisco Meeting, September, 1915) INTRODUCTION CRUDE oil attracted attention because of its excellence as a fuel for open-hearth furnaces; for making crucible steel and brass; for melting copper, lead, tin, zinc, nickel, silver, malleable iron, gray iron; and for the production of steam in all sizes and types of boilers. For heating furnaces, mold-drying ovens, core ovens, ore roasters, calciners, hot-air furnaces, sand drying, asphalt road work, etc., its superiority over other fuels is due to the fact that the heat is at all times under perfect control, so that a constant temperature may be attained and maintained at the will of the operator. This means a maximum amount and uniform quality of work. Crude oil is of two kinds, paraffine base and asphaltum base, and varies from 11 to 46 gravity Baumé. The light-gravity oil does not require heating before use; but oil of less than 20 gravity Baumé should be heated to just below its vaporizing point, in order to reduce its viscosity and to obtain the highest efficiency of combustion. Heavy California oil vaporizes at 230°'F., Mexican crude oil at from 175° to 210° F., and Beaumont, Texas, oil at 142° F. Fuel oil vaporizes at 130° F.

Jan 8, 1915

By P. C. Badgley

The purpose of this paper is to demonstrate the usefulness of systematic analyses of weakness patterns. The term weakness here includes structural features such as fractures, foliation planes, lineaments and bedding. Many of these features are mapped by geologists in the field, but analysis of the field date is frequently overlooked. Examples are presented to show the value of such studies in petroleum and mineral exploration, in dam site selection, and in regional tectonic interpretations. Numerous theories have been presented to account for the mechanics and time of origin of fracturing. This is an extensive subject and cannot be reviewed in detail here. The reader may wish to refer to other papers.*"5 It is sufficient to say that most fracture patterns can be related to one or more of the following force mechanisms: compression, tension, torsion and fatigue (inheritance by upward propagation of pre-existing fractures). Fractures generally occur in sets in a district. The angular relationships and other characteristics of the individual sets frequently help in determining the force mechanism and movement history of the deformation. From a geometric point of view fractures are commonly referred to as longitudinal, cross, or diagonal (shear), depending upon their orientation relative to other major structural features such as anticlinal axes and so forth. These terms will be used from time to time and are illustrated schematically in Fig. 1. FIELD PROCEDURE AND TREATMENT OF DATA In fracture studies it is very important to collect adequate field data. Fig. 2 illustrates a notebook sheet for recording significant field observations in sedimentary rocks. Slight adaptations have to be made for igneous and metamorphic terrains. Fracture density and persistence are very important factors in petroleum exploration for fractured reservoirs and mineral exploration. The density for each joint set is recorded in terms of number of joints per linear yard. The total number of joints at any one

Jan 1, 1962

By S. Usui, I. Iwasaki

The adsorption mechanism of dodecylammonium acetate (DAA) on mercury in potassium fluoride solutions at natural, near neutral pH was investigated. Difler-ential capacity combined with electrocapillary measurements on a dropping mercury electrode were found to provide a sensitive and reliable approach. A shift in the electro capillary maximum (or the point-of-zero-charge) towards positive polarization of the surface due to the adsorption of amine indicated a specific affinity of dodecylammonium ion for mercury surfaces. The amine was shown to adsorb competitively with potassium ion on mercury. Through correlation of the adsorption density of the amine, calculated from the thermodynamic analyses of the electrocapillary curves, and of the diflerential capacity curves, the adsorbed state and the orientation of the amine at the interface were considered. The similarities and the differences in the adsorption behavior of the amine on mercury and on such ionic solids as quartz, silver sulfide, and silver iodide were evaluated. With the promise of flotation providing a cheap and large-scale process for the upgrading of low-grade ores and magnetic concentrates, the iron ore industry has made a sustained search over the years for a flotation reagent of general applicability and high selectivity. Having shelves full of commercial reagents already on hand and anticipating more, both the users and the suppliers are in need of an experimental approach sensitive enough to differentiate the individual characteristics in each group of reagents. Therefore, the adsorption behavior of various flotation reagents on mineral surfaces from aqueous solutions has been a subject of much investigation. The current view of adsorption based on the electrical double-layer theory is formulated on the assumption that certain ions in solution act as potential-determining ions. Their concentrations fix the potential drop across the double layer and their adsorptions govern the surface charge.' Two methods used to study the adsorption

Jan 1, 1971

THE 143d* meeting of the American Institute of Mining and Metallurgical Engineers was held in New York, Feb. 19-22, 1934. It consisted of the annual business meeting, 45 technical sessions at which 217 papers were presented (more than ever before), two sessions of the Board of Directors, two meetings of Section delegates, three formal lectures, luncheon Monday, Tuesday and Wednesday for members and guests, three group dinners and five group luncheons, eight committee meetings, the annual reception and dinner dance, an informal dance, a smoke-dinner and the annual meeting of the Woman's Auxiliary. Attendance showed an improvement over the previous year, as follows: Total, 1534 in 1934, and 1475 in 1933; dinner dance, 543 and 426; smoker-dinner, 425 and 394; informal dance, 295 and 250; women's registration, 160 and 133; luncheons, 1034 and 734. The Coal Division held a general session and three sessions on Coal classification. It also met jointly with the Committee on Ground Movement and Subsidence. At the general session, John B. Dilworth presented a report of the Committtee on Methods of Valuing Coal Proper- ties and R. H. Sweetser a report of the Committee on Evaluation of Coal for Blast-furnace Coke. C. B Huntress, Executive Secretary of the National Coal Association, was the principal speaker at a luncheon on Monday, at which Eli T. Conner, Chairman of the Division, presided H. N. Eavenson, newly elected President of the Institute, and Edward W Parker, Secretary-Treasurer, of the Anthracite Institute, also spoke. The Executive Committee of the Division met Tuesday afternoon. The Sectional Committee on Classification of Coal met on Thursday morning and the Technical Committees on Scientific and Use Classification of Coal on Thursday afternoon. The Committee on Mining Methods held two general sessions, one for presentation of a half-dozen interesting papers on strictly mining subjects, the other on Aerial Transportation. It also participated jointly in a session on ground movement and subsidence with the committee of that name and the Coal Division The Institute's Standing Committee on Aviation had its inception at the session on Aerial Transportation

Jan 1, 1935

HeRbeRT Haas,—(communication to the Secretary*).—Fig. I plainly shows that the comparison of the steam-turbine and Diesel-engine plants was made on a basis of 6,000 kw. continuous operating load. The tabulation of costs for an 8,000-kw. load is merely done to show the relation of increased output on the unit power costs. Both plants would sacrifice their reserve capacity, which is to insure continuous operation, if operated to generate 8,000 kw. continuously; unless Mr. Hawkins advocates the operation of one of the turbines at 33.33 per cent. overload, retaining the other as a standby, which, besides overtaxing the turbine, results in a great loss of efficiency. It would be well for Mr. Hawkins to qualify certain of his statements. Thus, under the caption "Diesel Engines, Selection of Units," he says that '(two of the largest Diesel-engine builders take the position that, in the present state of the art, they would not attempt to put out units over 1,000 kw.;" he should qualify it by saying that "two of the largest American Diesel-engine builders take the position that, in the present state of the art in the United States, they would not attempt to put out units over 1,000 kw." The reason that American manufacturers restrict themselves at present to units of that size is to be found not so much in a lack of experience in building large units as in a lack of a sufficient demand for them in the United States to justify the heavy capital outlay connected with the development of such engines. There are relatively few localities in the United States where fuel prices are as high as they are in the South-, west, and regions of high fuel prices are sparsely settled and have a very limited demand for power. Where low fuel prices obtain, steam turbines are active competitors of Diesel engines for large power plants, particularly when the station load factor is low. As most of the American manufacturers of Diesel engines work under license agreements with European manufacturers, which limit their market to the United States and its possessions and Canada, a further limitation is imposed upon them, leaving to European firms practically the entire world as a market. The greater number of power plants range in size from 300 to 1,000 hp.; the average size of the central station, on a basis of all central stations in the United States, not greatly exceeding 500 kw.; in these sizes it is hard for steam engines to compete with Diesel engines, unless fuol oil prices are excessively high, and coal prices very low, or the exhaust steam is used for heating purposes.

Jan 1, 1917

By E. F. Miller

The subject " Safe Timbering of Working Places in Mobile Loading" is one that requires an analytical study of the strata both above and below the coal seam as well as the characteristics of the coal seam itself. The projection or mining plan must be based on economic roof control in which the application of timber can be minimized without incurring cost increases in other phases of production. The several types of loading machines in common use today are not adaptable to the same projections or timbering systems. Consequently the type of equipment to be used must also be considered. For these reasons the writer does not believe that the problems of timbering in working places can be discussed without simultaneously considering economic production as well as the safety of men and the conservation of equipment. Prior to the introduction of loading machines as a substitute for the pick and shovel system of loading coal, the care and maintenance of the individual working places were generally the responsibility of the coal loaders who worked in them. Up to that time very few coal companies had developed and applied fixed and definite standards for timbering the working places in the mines they operated. It is common knowledge that mechanical loading of coal has had several false starts in the last twenty-five years and it is only in the last decade that it has developed to the stage at which we now find it. During this twenty-five year period the management of the more responsible companies have come to realize the tremendous importance of roof control in coal mining. From a safety viewpoint, the lack of roof control has been and still is responsible for more than a third of the industry's annual fatality experience. In recent years workmen's compensation and insurance rates have steadily increased while the profit margin has decreased almost to the point of elimination. From an economic operating viewpoint, the failure to properly control roof is quite often the most costly single phase of coal mining. Since the manufacturers of loading machine equipment have so improved their machines that normal care and maintenance can reduce to a minimum the time lost because of mechanical failure the production delays from other causes have assumed a far greater importance. Roof control in the broad sense and in the light of concentrated mining plans or projections that are adapted to mobile loading should be regarded as one of the major problems in the inseparable phases of production and safety of the workman and equipment at the working face. The subject of this paper cannot be treated properly unless what is said here is based upon the broad and fundamental problem of genera' roof control. The suc-cessful solution of a problem arising in any industry must have its origin in a complete analysis of the known facts or factors that pertain to it. The several illustrations

Jan 1, 1949

By S. N. Singh, M. C. Flemings

Results are presented of a detailed study on the combined influences of ingot dendrite am spacing and thermomechanical treatments on the structure and solution kinetics of high --purity cast and worked 7075 alloy. Solution kinetics were found to depend sensitively on ingot dendrite am spacing and on details of therrnomechanical processing, including amount of reduction and extent of&apos; solution treatment before reduction. An approximate analysis is given for rate of solution of nonequilibrium second phase in the cast and worked structres; results of the analysis are compared with experiment. MICROSEGREGATION in high strength aluminum alloys manifests itself as "coring" (composition differences within the primary aluminum-rich phase), and as interdendritic second phase. The mechanism of formation of the microsegregation is understood, and approximate prediction of the amount of second phase is possible for simple binary systems.1,2 When alloy elements or impurities are present in amounts less than their solid solubility at solution temperature, any phases forming from these elements are termed "nonequilibrium" and can be dissolved by appropriate solution treatment. The rate at which the nonequilibrium phases are removed depends sensitively on their spacing (dendrite arm spacing in the cast material, or band spacing in wrought material). When alloy elements or impurities are present in amounts in excess of their solubility at the solution temperature, second phase particles form an "equilibrium" second phase that does not dissolve in heat treatment and may, in fact, coarsen in such treatment. Usual commercial, high strength, wrought aluminum alloys contain nonequilibrium second phases that were not fully dissolved during ingot processing. They also contain equilibrium second phases resulting from impurities present in amounts greater than their solubility. As has been shown by Antes, Lipson, and Rosenthal,3 and will be demonstrated further in a subsequent paper by the authors,4 significant improvements in mechanical properties of high strength alloys can be achieved by reduction or elimination of these second phases. Methods of elimination are 1) to employ high purity materials to minimize amounts of equilibrium second phase, and 2) to employ suitable thermomechanical processing techniques to fully eliminate nonequilibrium second phases. Work reported herein comprises a study of selected thermomechani- cal processing treatments, and of their influence on solution kinetics of wrought high purity 7075 alloy. EXPERIMENTAL PROCEDURE Melting and Casting. The bulk of the work reported was performed on a single ingot of high purity 7075 alloy. The ingot was 4 in. by 4 in. by 8 in. high, uni-directionally solidified following a procedure previously described.5 The mold was heated to 1350°F before pouring the melt. The bottom chill was carbon coated stainless steel. Water was circulated through the chill after the melt was poured. The 7075 alloy was prepared from high purity virgin material (aluminum, zinc, magnesium) and from master alloys (Al-50 pct Cu, A1-15 pct Cr, A1-5 pct Ti). Final measured melt composition (wt pct) was: Zn Mg Cu Cr Ti Fe Si Al 5.70 2.28 1.35 0.18 0.15 <0.002 <0.012 bal Melting was done in a silicon carbide crucible; all tools were coated with zircon wash to minimize iron contamination; degassing was by bubbling chlorine through the melt. che-rmomechanical Treatments. Detailed studies were made on material taken from a location approximately 13 in. from the chill and 51/2 in. from the chill (i.e., from 1 in. thick slices taken between 1 and 2 in. from the chill and between 5 and 6 in. from the chill). Solution treatment was done at 860°F in an air-circulating furnace with a "bottom drop" arrangement to achieve minimum delay time between solution treatment and quench. Samples solution treated in this way were 2 in. by 2 in. by 1 in. Temperature of the quench water was approximately 10°C. Mechanical reduction was by cold rolling. Samples 11/2 and 51/2 in. from the chill were treated for 12 and 24 hr, respectively, before cold rolling. Reduction by cold rolling was then 4/1, 16/1, and 35/1. In each case, several intermediate anneals (1/2 hr at 860°F) were used to permit reaching the final thickness without cracking; two such anneals were used for the 4/1 reduction, five for 16/1, and six for 35/1. After working, materials were again solution treated for various lengths of time from 0 to 48 hr and quenched in water. Structural Measurements. Secondary dendrite arm spacings were measured using procedures previously described.&apos; For each measurement reported, five photomicrographs were first made at X75. Measurements were made of dendrite arm spacings in at least 20 different grains (grain structure was equiaxed). Grain size measurements were made by running a number of random traverses across photomicrographs of the samples and obtaining the mean lineal intercept. Measurement of the volume percent of second phase and porosity was done by quantitative metallography. A two-dimensional systematic point count was used

Jan 1, 1970

By M. C. Flemings, T. Z. Kattamis

Dendrite morphology and grain size were studied in bulk samples of iron and nickel base alloys under-cooled up to 300°C. In the alloys studied, dendrite morphology gradually changes with increasing undercooling from the usual dendritic structure to a structure composed of cylindrical dendrite arms. At a critical undercooling of approximately 170°C in these alloys there is an abrupt transition to a fine-grained structure of spherical morphology. Final dendrite-arnz spacing of melts nucleated at less than the critical undercooling decreases with increasing undercooling and with decreasing distance from a chilled surface. Grain size of melts nucleated at greater than the critical undercooling decreases similarly with these factors. It is concluded that structure coarsening, with reduction of surface area as driving force, is the principal mechanism determining final dendrite-arm spacing in melts nucleated at small undercoolings and grain site in melts nucleated at large undercoolings. IN solidification of highly undercooled melts, nuclea-tion and growth of the solid is accompanied by a rapid release of latent heat of fusion. The heat release is sufficiently rapid in bulk specimens that it takes place essentially adiabatically with respect to the surroundings; hence the specimen heats up ("recalesces") to some maximum recalescence temperature. For bulk liquid metals and alloys, a simple thermal balance shows the undercoolings obtainable in bulk samples are not sufficient to lower the maximum recalescence temperature below the equilibrium solidus temperature. Hence, some liquid always remains at the end of recalescence; this liquid must solidify by rejection of heat to the surroundings. Metals, including iron and nickel base alloys, normally freeze with only a few degrees of undercooling. In general, nucleation begins on impurity particles present in the metal, at a "heterogeneous nucleation temperature" that is quite close to the equilibrium liquidus temperature. Very small droplets of metal can be undercooled considerably before nucleation occurs,1-4 presumably because subdivision of the liquid reduces the probability of solid impurity in a given droplet. Following early work on metal droplets,&apos; a series of studies has shown that it is possible, without great difficulty, to undercool bulk samples of many metals and alloys. Undercoolings obtainable are approximately two tenths of the melting point for nickel, iron, copper, and other metals and alloys.5-9 Specimen sizes have generally been in the range of 50 to 500 g. Studies on undercooling to date have been concerned primarily with techniques of undercooling and with nucleation and growth kinetics. Only limited consideration has been given to dendrite morphology in under- cooled alloys. One such study, in bulk Cu-Ni alloy,8 showed that at small undercoolings a typical dendritic structure was obtained. At undercoolings the order of 175°C the structure of a Cu-40 pct Ni alloy became "ray or starlike", and a dense network of subbound-aries appeared. At still larger degrees of undercooling, of the order of 250°C, the structure became more random and included an ensemble of globular forms. Comparable results were obtained by walker10 on Cu-Ni alloys, and by Kamenetskaya et al.11 in research on Cu-Ni, Sb-Bi, Fe-Ni, and Fe-Cr alloys. In this work, study was made of the processing parameters influencing dendrite morphology and grain size in undercooled alloy melts. Experiments were specifically designed to show the effects of coarsening ("ripening") during solidification on final casting morphology. EXPERIMENTAL PROCEDURE Apparatus used was patterned after that of Walker,10 Fig. l(a). Melting was by induction under reduced pressure of helium. Two different types of crucible materials were used; there was no difficulty in obtaining substantial undercooling in both types of materials. Alumina crucibles were used for the bulk of the runs made, with a glass coating separating the metal from the crucible walls. Other runs were made using fused silica crucibles with or without slag coating. A graphite susceptor was employed around the crucible to aid in melting and to reduce melt stirring. The major portion of the experimental work was on

Jan 1, 1967

By J. F. Smith, J. E. Davison

A value for the enthalpy of formation of z2 of -3.14 i 0.21 kcal per g-atom has been measured by the technique of acid solution calorimetry. This result is in quite good agreement with two earlier determinations by tin solution calorimetry and by direct reaction caloriinetry, and averaging of values determined from the three independent calorimetric techniques gives enhanced precision and accuracy with AHh8 (CaMgZ) = - 3.15 i 0.05 kcal per g-atom. For comparison with experimental data, values for the enthalpies of formation of CaMgz, SrMgz, and BaMgz of -9.8, -7.9, and -2.8 kcal per g-atom were estimated from a calculation based on the LVigizer-Seitz approximation as modified by Raimes for polyvalent elements. While complete quantitative accord between these calculated talues and available experimental data is lacking, nonetheless numerical accord is better than might be expected and, more importantly, parallel numerical trends are observed between experimental and calculated vnlues. WITHIN the past decade the enthalpy of formation of CaMg, has been determined a) from measurement of magnesium vapor pressures over binary Ca-Mg alloys,&apos; b) by solution calorimetry with liquid tin as the solvent,&apos; c) from measurement of hydrogen vapor pressures over ternary alloys of calcium, magnesium, and hydrogen,3 and d) by direct reaction alorimetr. The value from tin solution calorimetry is the most precise and is probably the most reliable, and this value is within the quoted uncertainties of the other three experimental results. The overall agreement among the four independent investigations is quite good, particularly so when the diversity of techniques is noted. On the basis of this agreement, CaMgz was chosen as a test material to evaluate the operation of a newly constructed apparatus for the determination of enthalpies of formation of intermetallic phases by acid solution calorimetry. This was believed to be a severe test because of the high chemical reactivity of both calcium and magnesium which reactivity presumably accounts for the fact that an early determination5 of the enthalpies of formation of Ca-Mg alloys by acid solution calorimetry yielded values significantly more negative than the four recent determinations. EXPERIMENTAL APPARATUS AND MATERIALS Experimental Apparatus. The enthalpy of formation of CaMg, was determined by measuring the difference between the heat evolved when dissolving the metallic compound and the heat evolved when dissolving equivalent amounts of unreacted metallic elements in hydro- chloric acid. This was done differentially with an apparatus consisting of twin calorimeters which were constructed to be as nearly identical as possible. The advantage of differential calorimetry is that systematic errors arising from the individual calorimeter design tend to cancel. A schematic representation of the apparatus is shown in Fig. 1. A dead air space around both calorimeters was provided by a large, thermally insulated jacket. Each calorimeter consisted of a 2-liter Dewar flask which was completely enclosed in a copper container. Each Dewar contained 1600 g of 2.5hr HCl to act as the solvent, and thermal effects resulting from solvent evaporation were minimized by covering the acid with 50 g of mineral oil. There was no detectable reaction between the acid and the mineral oil. Equivalent amounts of mechanical energy were added to the calorimeters through twin stirring rods which were driven at the same rpm by a single motor with the intent of the stirring being to maintain thermal equilibrium throughout the solvent. To calibrate the heat capacities of the calorimeters, known amounts of electrical energy could be added by passing measured voltages and currents for known times through submerged heaters, approximately 20 ohms, which were wound noninductively from Manganin wire. A 6-v storage battery was used as a power source, and a dummy heater was used as an exercise circuit to allow the battery to stabilize at a constant electromotive force before energizing one or the other of the calorimetric heaters. A type K-2 potentiometer was used to measure the potential drop across an energized heater while the current was determined from the potential drop across an external standard resistor. Times of energization were measured with an electric timer, and the electrical energy supplied to a heater

Jan 1, 1969

By J. B. Austin

MEASUREMENTS of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage trans-formed on linear coordinates against time on either a linear or a logarith-mic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even inter-polation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolation is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valu-able when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decom-position of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1938

By Thomas R. Scotese

A rock mechanics instrumentation and monitoring program was implemented during pillar extraction at Gulf Mineral Resources&apos; Mt. Taylor Mine, the deepest uranium mine in the U.S. Three types of monitoring were employed: (1) drift convergence around stopes (using a portable tube extensometer), (2) stress changes in pillars (using vibrating wire stressmeters in horizontal boreholes), and (3) load changes in haulageways under stopes (using vibrating wire load cells in jack stands). Results include convergence-time graphs, convergence contour maps, stress-time graphs, a stress increase contour map, load-time graphs, and abutment load limit maps. Major factors influencing results include (1) size of pillars around the extraction area, and (2) presence and orientation of a major fault adjacent to one extraction area. These factors, combined with pillar extraction, produced evidence of load transfer over 120 m from a stope measuring only 55 m x 45 m. Vertical stress increases of 7 to 17 MPa (1000 to 2500 psi) within 60 m of the stope were obtained using the stress- meter manufacturer&apos;s method. The fault apparently prevented load transfer in the down-dip direction but increased load transfer in the up-dip direction. Convergence rates of up to 1.3 cm/day (0.5 in/day) were measured at two stations. Instruments were generally reliable despite adverse underground conditions. The instrumentation and monitoring program at Mt. Taylor provided a warning system against ground control problems and a characterization of ground behavior for future development and extraction of pillars. Recommendations are made for future mining and instrumentation practices.

Jan 1, 1984

By B. Egeberg

IN A previous paper1 the authors dealt with the physical properties of cold-rolled and heat-treated Britannia metal of the approximate composition Sn, 91 per cent., Sb, 7 per cent. and Cu, 2 per cent. It was found that cold rolling to more than 50 per cent. reduction produced a continuous softening of the metal when measured by the Brinell machine, whereas the Shore instrument indicated increased hardness; that the strength of the material followed the Brinell hardness and that the metal therefore became weaker the more it was cold-rolled; and further, it was found that hardness and strength could be largely restored to the cold-rolled metal by "baking" for about one hour at any temperature, between 200° and 450° F., the melting point. The higher the baking temperature, the more effective was the heat treatment as far as increased hardness was concerned. It seemed to be of little importance whether the metal was soaked or not at the baking temperature for a great length of time and the rate of cooling seemed to be immaterial. The present paper deals with the same alloy and more particularly with the resistance towards various forms of stress - tensile, bend and deep drawing. The metallography of Britannia metal has in part also been covered and an explanation attempted for the abnormal behavior of this alloy.

Jan 1, 1929

By Fredrick C. Kruger

Risk capital for mining ventures becomes harder to get each year as the costs for exploration, construction and money continue to skyrocket in today&apos;s inflationary economy. Because of this and because mining prospects must compete for the same dollar as many other needs of a diversified company, then the success or failure of any new proposal depends on how well its return on investment compares with all other capital requests. Mr. Kruger presents case histories showing what it costs to explore for new mines, how many of these prospects reward their promoters with success and how well some of the more famous mines have paid off.

Jan 9, 1969

By R. S. French, W. R. Hibbard

M. Balicki—As one who some years ago spent much time searching for an alloy with high thermoelectric power that would be suitable for heat energy-electric energy converter based on the principle of a thermoelectric pile, I would like to make a few comments touching upon that aspect of this excellent paper. The specifications which one of the authors has formulated so aptly do not appear to me as complete, and I would like to add to them the following two demands: (1) Melting point not less than 500°C and (2) elongation on 2 in. at least 5 pct. Condition 1 would insure good thermodynamic efficiency of the pile by permitting a reasonably high temperature of the hot junction and at the same time making it suitable for such application as salvage of vast amounts of energy which is lost in the form of sensible heat of waste gas leaving industrial and other furnaces. Condition 2 is also a very important one; particularly, because of the fact that all elements and alloys which exhibit attractive thermoelectric properties seem to be as a rule very brittle. The design, erection, and maintenance of a pile incorporating a brittle material in one of the most crucial parts of the converter would be a very difficult and costly affair indeed. To illustrate this point I may mention great difficulties I encountered when trying to make thermocouples of silicon. Casting of 1/4-in. rods in iron or graphite mould yielded only broken pieces which had to be welded into a bar. Such a bar had to be handled very carefully during the determinations. Raising the molten silicon by vacuum into a silica tube and solidifying it there solved the problem of stability as well as that of electrical insulation of a bar. On tests this bar (98.5 pct Si) showed dE/dT = — 275.5 microvolts per degree C vs. copper. Thermocouples made of this grade of silicon and pure nickel developed 0.39 v when temperature of the hot junction was approximately 1000°C. The possibility Dr. Gonser has mentioned of trying to impart to metals good thermoelectric properties by alloying them with silicon, has been considered. The preliminary survey which I have made was, however, disappointing. Perhaps, it will be advisable to record the results obtained (table VI), as this might save repetition of search in fields already covered.

Jan 1, 1951