Search Documents

By J. W. Spretnak, H. R. Ogden, A. G. Imgram

The effect of working reduction, stress-relief annealing, and recrystallized grain size on the tensile and notch-tensile properties of molybdenum and Mo-0.5 Ti was studied. It was found that increasing the amount of working reduction increased the strength and reduced the tendencies toward brittle behavior. Stress -relief annealing did not alter the strength but lowered the transition temperature. Increasing the recrystallized grain size lowered the strength and raised the transition temperature. The notch -unnotch strength ratio began to decrease with decreasing temperature at temperatures below those at which the notched ductility fell to zero for all of the micro structural conditions investigated. BEING bcc metals, the refractory metals in Groups Va and VIa (V, Cb, Ta, and Cr, Mo, W) undergo a ductile-to-brittle transition and exhibit brittle fractures at low temperatures. Previous research has shown that molybdenum and tungsten not only have higher transition temperatures than columbium and tantalum but show a marked sensitivity of transition temperature to structure as well.' Recrystallized materials become brittle at considerably higher temperatures than is the case with material having a worked or fibered micro-structure. Evidence of structure sensitivity has also been detected in columbium- and tantalum-base alloys containing appreciable amounts of molybdenum or tungsten such as F-48 (Cb-15W-5Mo-1Zr) and Ta-10w.2 This paper describes the results of research conducted to further evaluate the effects of metal. lurgical structure on the low-temperature tensile and notch-tensile properties of molybdenum and Mo-0.5Ti. The effects of rolling reduction, stress-relief annealing temperature, and recrystallized grain size were studied. Considerable progress has been made in explaining the fundamental mechanisms of the flow and fracture characteristics of bcc metals. Several of these concepts are helpful in interpreting the data obtained in this study. Brittle fractures occur when the highly temperature-sensitive yield strength equals, or exceeds, the temperature-insensitive brittle cleavage fracture stress.3 The rapid increase in yield strength with decreasing temperature, characteristic of all bcc metals, is therefore of primary concern. petch4 has described the yield strength, ay, (stress required to initiate plastic flow) of bcc metals by the expression where ai is the frictional resistance to slip, Ky is a constant numerically equal to the slope of a a vs curve, and 2d is the average grain diamefer. The oi term itself is thought to be composed of a temperature-insensitive component dependent on impurity content and second-phase particles and a temperature-sensitive component dependent on the Pierls-Nabarro force.5 This equation has also been demonstrated to hold for the flow stress (stress required to maintain continued plastic flow).' Brittle-crack nucleation is thought to occur by the coalescence of dislocations piled up in slip planes at sessile dislocations or twin and grain boundaries.7,8 These proposed mechanisms require that a large number of dislocations be released into the active slip planes so that sufficiently large stress concentrations are produced at the dislocation pile-ups to enable coalescence into a micro-crack. Therefore, at least a microscopic amount of slip must occur in some grains to facilitate initial crack formation. Cottrell 7 has predicted that brittle fracture, nucleated by slip, should occur when where ty is the shear yield strength, ß = 1 in un- notched xension, u is the shear modulus, and y is the effective surface energy. This equation incorporates the Griffith concept of fracture that a crack will propagate if the decrease in strain energy equals or exceeds the increase in surface energy.

Jan 1, 1964

By Leonard Larson

BEFORE direct or wet smelting of copper concentrate was adopted at the McGill smelter, in November 1932, actual furnace smelting tests had indicated the possibility of smelting between 400 and 500 dry tons of wet concentrate per furnace day. Under calcine smelting practice, solid charge up to 1165 tons per furnace day had been smelted. It was realized that in order to smelt wet tonnage in equivalent amount per furnace day, a higher combustion rate and higher temperatures would be neces-sary within the furnace. The reverberatory furnace considered in the following history of wet-smelting de-velopments is a unit 127 ft. long and 28 ft. 8 in. wide, inside dimensions (Fig. r). This furnace was in operation through all the years from 1934 to date. During 1933, the first complete year of direct or wet smelting, the plant was on a curtailed copper-production basis and the available concentrate tonnage to be smelted was limited. The average coal-firing rate in the reverberatory for that year was 124 tons per furnace day. This rate was lower than the average for years immediately preced-ing under calcine smelting practice. With this coal-firing rate, an average of 391 tons of new metal-bearing material (N.M.B.M.) was smelted per furnace day. The following year, 1934, the coal-firing rate was in-creased to 139 tons and the smelting rate increased to 448 tons N.M.B.M. per fur-nace day. In succeeding years production required that either more tonnage be smelted in the one furnace or an additional furnace be placed in operation. With this situation confronting the smelting depart-ment, it was determined to continue the program of increasing the coal-firing rate and also to intensify the temperature in the smelting zone of the furnace. In order to accomplish this, various improvements were made to aid combustion within the furnace. The burners were enlarged, in-creased primary air was supplied to the burners, and changes were made in the furnace to enlarge and streamline the out-let, thus increasing the furnace draft.

Jan 1, 1940

G. A. Burr, Parral, Chihuahua, Mexico (communication to the Secretaryt): I regret that Mr. Norris did not give more attention to the hoisting of water in inclined shafts or slopes: the only slope mentioned being Hickory Ridge Slope, No. 4, of the Union Coal Co. The surface arrangement, illustrated in Fig. 12 of his paper, if not unpractical, is at least unscientific and cumbersome. It is my opinion that the back- and sideguides shown in Fig. 12 are not only unnecessary where rails are used as a track, but are unsafe, excepting in the case of a very firm hanging-wall, or roof, and sides of vein-matter, having absolutely no tendency, either to settle from the back, or to squeeze from the sides, an effect which would inevitably force the guides out of alignment. The accompanying illustration, Fig. 1, shows what I consider a better method of hoisting water than that described by Mr. Norris. This method is based on the general practice in metalliferous mines of the West, where skips are used in slopes; and, while it is not original with me, I have frequently used it with very satisfactory results for dumping both ore and water.

Jan 1, 1904

By H. M. Merry

The graphic methods and records described in this article have been developed, with satisfactory results, for the use of executives of the Chino Copper Co., in Hurley, N. Mex. Particular attention is directed to the use of large wall-charts, the quick reference display of large charts, the scale notation of metallurgical charts shown in Pig. 3, and the inclusion of mesh extraction on screen analysis diagrams. To properly comprehend the operation and metallurgical results from a concentrating plant, a daily record of essential data is kept, usually involving the dry weight of ore milled or treated, dry weight of concentrate or metal produced, assay values of heading, assay values of tailing, assay values of concentrate, and percentage of extraction or recovery. In addition it is often necessary to record moisture, pulp density, or dilution, percentage of weight of oils and reagents employed; screen analyses of grinding conditions, oversize, etc.; assay values of non-valuable or interfering substances; cost data; and such special information as may be required. GRaphic Presentation . Close analysis is necessary of a daily operation involving such a number of factors, the relation and influence of which may be of great importance in the treatment scheme. When the analysis is made from a numerical tabulation, the chance for one or more obscure, but perhaps important, factors to escape notice is considerable, therefore the need for an accurate, readily digestible presentation of metallurgical data is obvious.. Graphic records of milling operations are frequently used, but owing to the wide range of magnitude and values, and the number of factors involved, the customary practice of assigning different values to the same ordinates, as in Fig. 1, results in a complex and intricate record which makes little appeal to a busy operating official. The methods shown in Figs. 2 and 3 are devised to display such data in a clear and legible manner, without confusion.

Jan 1, 1920

By Herbert H. Kouns, Harlan W. Nelson, Bruce O. Buckland

GASIFICATION of coal under pressure produces a gas that may be used as the fuel in a gas turbine. The pressure produced by a gas-turbine compressor (5 to 9 atm) should allow the use of high firing rates without unreasonably high solid carry-over rates. Hot make-gas with the tars contained in it in the vapor form can be used in a gas turbine. Most of the ash can be removed through a grate, and only a small portion of the ash and any of the solid combustible material carried over by the make-gas requires separation. The gas stream from which separation is required is a small portion of the total flow of a gas-turbine plant and hence the separator size will be small. The gas stream is reducing and will not, therefore, allow separator fires to occur. The response of the producer to rapid load changes is satisfactory. Only the air rate must change substantially in synchronism with the load. The coal feed, the steam addition to the blast, and the ash-removal rate can follow the load changes with time lags in the order of minutes. The necessary control equipment is simplified by these producer characteristics. With these possibilities in mind, the Steam Turbine Division of the General Electric Co. made arrangements with Battelle Memorial Institute in January 1945 to investigate the problems of the gasification process. A number of tests were made during this investigation on an updraft producer with a grate area of 1 sq ft. The equipment used has been described and the results of the tests made between 1946 and 1950 have been reported.1 The testing with this small producer was recently completed. The concluding tests were run to determine the effectiveness of a clinker-grinding grate and the effect of the operating conditions on the amount and character of the solid carry-over. The present paper describes the producer as modified, and gives the results of the tests using three coals. Another method of using coal in gas turbines is to pulverize it and burn it directly in the combustion chambers. This plan is being tried by the Loco- motive Development Committee of the Bituminous Coal Research, Inc., whose investigation has reached the stage of tests of full-sized equipment.

Jan 1, 1953

By Howard W. Miller, Charles R. L. Oder

APPROXIMATELY 5000 tons of zinc ore a day was mined during 1943 in the Mascot-Jefferson City district in East Tennessee. This ore came from the Kingsport formation, a part of the Knox dolomite, of Ordovician age. The Kingsport is composed of 350 to 400 ft. of limestone and dolomite. Thin cherts, sandy layers and shales are numerous. Frequently, the limestones are altered to crystalline dolomite. The Kingsport is divisible into four main lithologic zones. These divisions are illustrated in an accompanying table, which gives detailed sections of the ore-bearing beds as found in the mines and shows the exact positions of the various ore zones within the formation. Key beds are described and the practical applications of stratigraphy in mapping, prospecting and mining are discussed.

Jan 1, 1945

By Junnosuke Yamamoto

Substituting sodium hydroxide for sodium carbonate as a binder in a glass batch yields harder pellets with a lower melting point. This paper explores the degree of NaOH substitution that is feasible, and compares pellet hardness, and amount of dusting with the degree of NaOH substitution. The effects of the the amount of soluble silicate in the pellet and residual hydroxide concentration in the pellet on pellet hardness are also studied.

Jan 1, 1977

By David B. Reger

The value of carbon ratios in determining the boundaries of possible oil deposits appears to have passed the hypothetical stage. The theory that the ratio of fixed carbon in pure coals is an invariable index of incipient metamorphism in both surface and underground rocks and that it may be applied in defining the limits of petroleum, advanced by David White,' has been received with keen interest by many petroleum geologists. Detailed isocarb maps have been prepared of the Pennsylvanian area of North Texas and Eastern Oklahoma by M. L. Fuller.² A similar map of the coal-bearing area of West Virginia is given here. An isocarb3 is a line showing an equal fixed-carbon percentage, pure coal basis; the term has been proposed by David White to supersede a less expressive nomenclature. The term carbon ratio is applied to the pereentage of carbon in pure coal after water and ash have been eliminated. As a comparatively small number of analyses have been made on this basis, it is usually necessary to compute the ratio by dividing the fixed carbon of the proximate analysis by the sum of the fixed carbon and volatile matter of the same analysis. Many thousands of proximate analyses have been made by the West Virginia Geological Survey, covering nearly every county in which coal is found. Numerous others have been made by the U. S. Geological Survey and the U. S. Bureau of Mines, but as uniformity of results is best secured by adhering to one set of analyses, the tests of the West Virginia Survey have been cxclusively used.

Jan 1, 1921

By F. V. Lene, E. J. Westerman

The recrystallization behaviors of two extruded and cold-drawn experimental sintered aluminum powder alloys, containing 1.75 and 3.0 pct Al2O3 by weight, were compared with that of extruded and cold-drawn commercially pure alumirzum. The kinetics of recrystallization of the alloys are described semiquantitatively. For the alloy containing 1.75 pct A l203 the rates of nucleation and of growth were also semiquantitatively determined. THE most striking property of aluminum alloys strengthened by a dispersion of Al2O3, the so-called SAP alloys, is their stability at elevated temperatures. One of the manifestations of this stability is their resistance to recrystallization after they have been cold worked. Most of the commercial grades of either the Swiss SAP or of Alcoa's Aluminum Powder Metallurgy Products have not been recrys-tallized after cold working, even when they are heated for a long time at a temperature near the aluminum melting point. Lenel, however, observed that the dispersion strengthened aluminum alloys with a larger spacing between the oxide particles than that of most commercial grades would recrys-tallize.1 It appeared to be of interest to further investigate the mode and kinetics of recrystallization of these alloys, and to compare their recrystallization behavior with that of commercially pure aluminum. Because homogeneous deformation of these SAP alloys in tension did not provide sufficient cold work to induce recrystallization, they were cold worked by wire drawing; the nonuniformity of this deformation unavoidably complicated the interpretation of the recrystallization studies. EXPERIMENTAL DETAILS Extrusions—Two types of sintered aluminum powder extrusions were used in this study. One type, designated AT-400, was produced from Reynolds atomized aluminum powder consisting of spherical particles averaging 3µ in diam and containing 1.75 wt pct of Al2O3. This powder was very similar to the R3M powder from which extrusions were previously prepared with an average spacing of 0.9µ between oxide particles.2 The second type, designated MD 2100, was produced from Metals Disintegrating Co. flake powder containing 3.0 wt pct of Al2O3, with an average flake thickness of 0.8µ. The average spacing between oxide platelets in MD 2100 extru- sions was 0.45µ.2 Powder compacts of 3/4-in. diam were extruded at 1000°F into 0.097-in. diam (AT-400) and 0.093-in. diam (MD 2100) wires by methods previously described.3 In order to compare the recrystallization behavior of sintered aluminum powder extrusions with that of wrought commercially pure aluminum 3/4 in. rod stock of 1100 F aluminum was extruded at 1000°F into 0.102-in. diam wire. Wire Drawing—Tungsten carbide dies were used for the AT-400 and 1100 F alloys. They had an included angle of about 15 deg and reduced the wire area approximately 7 pct per pass. Steel dies with an included angle of 11 to 13 deg and an average reduction per pass of 10 pct were used for drawing the MD 2100 alloy, because drawing this alloy through the carbide dies produced overdrawing defects. Heat Treatment—The cold-drawn wires were cut into small samples, and the deformed ends were etched off. The samples were each wrapped tightly in a single layer of aluminum foil, and individually isothermally annealed in a lead bath. Metallography—The modes and kinetics of recrystallization were determined by metallography. Mounted and polished specimens were anodized in a solution of 1.8 pct HBF4;4 examination under polarized light clearly revealed their grain structures. The recrystallized grains were generally much larger than those of the unrecrystallized matrix, and could clearly be distinguished because they alternated between maximum and minimum light reflection when the microscope stage was rotated, while the unrecrystallized matrix had a comparatively homogeneous "salt and pepper" structure. The fractional recrystallized volumes of the dispersion hardened alloy wires were determined by cutting and weighing of recrystallized and total transverse areas on photomicrographs. The recrystallized grains in the 1100 F alloy were too small to be cut out individually; therefore a combination of cutting and lineal analysis was used in this case. RESULTS AND DISCUSSION Modes of Recrystallization—The modes of recrystallization of the three alloys varied widely. In the 1100 F alloy nucleation and growth started in the region midway between the center and the surface;

Jan 1, 1961

By David E. Hyatt, Christopher H. Cox, Franklin T. Davis

INTRODUCTION The composition of water used in the flotation process has always been of primary interest to the flotation metallurgist. It is by alteration of the chemistry of the water introduced to the process that flotation separation is effected. In only a few cases has it been necessary to treat available water prior to use in the process. In the past, flotation tailings were treated for the removal of solids via the tailings dam and water decanted from the dam was either recirculated to the process or discharged to the surface water system. The choice of recirculation or discharge was based upon water availability, effect of recycle water on the process, and economic considerations. The Federal Water Pollution Control Act Amendments of 1972 have charged the United States Environmental Protection Agency with establishing effluent limitations from point sources of discharge into the navigable water of the United States. A detailed study, sponsored by EPA, of the water of ore processing plants took place in 1974 and 1975 and guidelines for these plants will presumably have been published by the time this paper has been presented(1). The action of many of the individual states preceded the EPA in this attempt to regulate the quality of the water discharged from industrial point sources. Even with recycle of tailings water, some water is discharged from tailings dams into the substrata and at least one state is currently preparing guidelines for the quality of water discharged into the substrata.

Jan 1, 1976

By C. C. Templeton, S. S. Rushing

Methods previously developed for the study of air-liquid displacements in microscopic capillaries (inner diameters of 3 to 40 microns) have been used to investigate oil-water displacements in capillaries initially filled with water. Displacement calculations assuming perfect displacement and no capillary pressure hysteresis yielded oil effective viscosities smaller than the macroscopic viscosities. For a given liquid pair, the oil effective viscosity decreased both with decreasing capillary size and with increasing oil-water viscosity ratio. This behavior can be explained by the existence of an annular water film (20 A to 260 A thick) on the capillary wall. When the capillary was first filled with oil, the ratio of the oil effective viscosity to the normal oil vircosity was highest for the first water displacement and decreased with subsequent displacements. Sometimes the oil effective viscosity ratio during the initial water displacement was greater than unity. INTRODUCTION In a previous paper1 a technique was described for studying air-liquid and liquid-liquid displacements in very small capillaries of uniform diameter, in the hope that such microscopic data would further the understanding of the nature of multiphase fluid flow through porous media. That paper contained comprehensive data for air-liquid displacements in Pyrex capillaries, with a few data for oil-water displacements in capillaries initially filled with water. The purpose of this paper is to present more complete results for oil-water displacements in capillaries initially filled with water, and to describe for the first time such observations in capillaries initially filled with oil. In this way the effect of the wetting history of the system upon the displacement process may be studied. METHODS The basic techniques employed were described in the previous paper.1 The measuring procedure and the working equations will be briefly summarized here and a few modilications will be pointed out. For the present study, temperature control within 0.l °C was obtained by placing the microscope and its immediate accessories in a thermostated air bath made of a steel frame covered with plexiglas. The water and oils used in this work were the same as in the previous paper,1 with the addition of "Medium Mineral Oil, U.S.P. supplied by the Harshaw Scientific Co. When the first liquid was introduced into the horizontal capillary, the air-liquid static capillary pressure Poc was measured along the observable length of the capillary. From the relation Poc = 4y cos 0/d, the capillary diameter d could be calculated from Poc if the "microscopic" air-liquid boundary tension, To = y cos On, was taken as equal to its known "macroscopic" value. This calculation involves assuming that cos 6 = 1 and that capillary size or the resulting high interfa-cial curvature has no effect on surface tension, or y cos 6, as was verified by our work, and also by that of Cohan and Meyers on air-liquid-solid systems. For several capillaries these calculated diameter values were compared with values measured visually with a filar micrometer eyepiece. For a given capillary the average values for the two methods agreed within 1 or 2 per cent, but the visual values were less reproducible than the calculated values. Further the calculated values were much less subject to personal bias and took into account any slight ellipticity that might be present. Hence diameters calculated from air-liquid Poc data were used throughout this paper. The second liquid was introduced in such a way that a single spherical interface separated the two liquids. Displacements were always made with a constant pressure, Pt, between the ends of the capillary. The times (t) at which the interface passed certain

Jan 1, 1957

By A. S. Malicsi, R. J. Lipp, I. Iwasaki

A loch-grade copper-nickel deposit, with an estimated 4.6 Gt (5 billion st) and average analyses of 0.6% copper, 0.2% nickel, occurs in northeastern Minnesota. In addition to copper, nickel, cobalt, and precious metals, the Duluth gabbro contains magnetite, ilmenite, olivine, plagioclase, and biotite. It u estimated that flotation tailings that would be produced by a concentrator of optimal size to sustain a smelter would amount to 20 Mt/a (22 million stpy). The flotation tailings, having already been ground, warrant a closer examination for recovery and use of potential byproducts. Residual sulfide minerals and fibrous minerals may also be isolated and treated separately for useful purposes or for disposal in an environmentally acceptable manner. Two flowsheets were developed; one involving preconcentration by low- and high-intensity magnetic separation and another involving preconcentration by gravity concentration. Concentration methods for recovering and purifying individual byproduct minerals were investigated. From their chemical, physical, and mineralogical characteristics, the potential areas of application and marketabilities of each product fraction were surveyed.

Jan 1, 1985

By William O. Hotchkiss

IN COMMON with every other good citizen I long for conditions that will make perpetual peace a reality throughout the world. I have studied the statements of our public men relating to what we must do to bring this about after this war is over. In most of these I find one common error. They always build their plans on the unstated, subconsciously accepted premise that there can be such a thing as an ideal nation whose citizens are possessed of infinite wisdom and actuated only by motives that are above reproach. This heavenly vision fails to correspond with the facts. We wish it could be true but we are forced sadly to admit that the human beings that will live here after this war is over are going to be much like the fallible race that has occupied our planet for the past centuries.

Jan 1, 1943

By Don H. Baker

THE need for new or improved refractory materials has caused metal phosphides to be given renewed scrutiny. Some metal phosphides show high-temperature inertness, are exceptionally hard, and exhibit a marked resistance to chemical attack. Various metal phosphides have been prepared for study by direct combination of the elements,'-' by reaction of metal or metal compounds with phosphine or phosphorus trichloride,'"' by thermal decomposition of a metallic phosphate or phosphite,"-'8 and by molten salt electrolysis.19 Electrolytic preparation of phosphides of titanium, manganese, and chromium from their oxides is reported in this paper. An externally heated 3-in.-ID by 6-in.-deep graphite cell, that served as the anode as well as a container for the electrolyte, was used in these investigations, and a suspended, centrally positioned graphite rod served as the cathode. A closely fitting silicon carbide furnace liner minimized atmospheric oxidation of the crucible. Electrolyses were performed for predetermined periods and current settings. Preliminary research had indicated the more efficient current and potential settings that could be used. Upon completion of the deposition period, the deposit was hot-stripped from the cathode. The mass of crystalline deposit, plus occluded and adhering salt, was crushed to minus 10 mesh and hot-leached in dilute hydrochloric acid. The leached crystalline material was water-washed, dried, and sampled for analysis. Products were identified by X-ray diffraction and standard analytical procedures. Electrochemical studies were initiated to establish the optimum conditions necessary to produce manganese phosphide (MnP), titanium phosphide (Tip), and chromium phosphide (CrP). Among the factors studied were the operating temperature, the imposed current, and the electrolyte system. If the temperature, or imposed current, was too high, deposition of phosphorus resulted, and if either were too low, partially reduced lower oxides were deposited. The operating conditions established for repetitive high-quality production of metal phosphides of the MP structure are presented in Table I. The metal phosphide crystals varied in size, but all had a definite metallic appearance. Typical are the crystals of CrP shown in Fig. 1. Evaluation data and analysis of the crystals are presented in Table 11. Efforts to measure resistivity of these three compounds over the temperature ranges of 250o to 400°K were hampered by the small physical size of the crys-

Jan 1, 1968

By J. E. Russell, Y. J. Wang

In this paper, we report the results of a study of the characteristics of Texas lignite based on a proximate analysis data base previously published by the Bureau of Economic Geology, University of Texas at Austin and the U.S. Bureau of Mines. The original impetus for this study was the desire to perform a parameter study in connection with the siting of potential underground gasification tests in Texas. A numerical model of the gasification process was available and required proximate analysis data, among other parameters, as input. If proximate data were available for a particular site, a prediction of the product gas quality could be made. However, in preliminary siting studies, it would be advantageous to know what the desirable characteristics of the lignite are, in order to target general areas for drilling. Consequently, a parameter study was in order. This paper presents the methodology required to systematically vary proximate analysis parameters and estimate the corresponding energy content for various group(or formation)-facies classifications of Texas lignite.

Jan 1, 1983

By R. Neilson Clark

The discovery of a thin pay streak, yielding carbonates of copper; native silver, and perhaps chloride of silver, was made on the 9th of April, 1874, within the trachytic belt which forms part of the Sierra Mojada. The discoverer named it the Humboldt Mine. On the 2d of May, 1874, another discovery was made, in a northwest direction from the Humboldt, at about five hundred feet distant, this was named the Pocahontas Mine. After some exploration these two discoveries were proven to be on the same vein. To the southeast of the Humboldt a claim had already been taken up, called the Virginia; and to the northwest of the Pocahontas, one called the Southeast Leviathan. On these' last two this same vein has been found and worked. This paper will therefore treat of the Humboldt-Pocahontas vein, as worked on these four claims, to wit: beginning at the northwest, the Southeast Leviathan, the Pocahontas, the Humboldt, and the Virginia claims. Since the spring of 1874, there has been sunk on this vein a total of twenty-seven hundred and fourteen feet of

Jan 1, 1879

By D. J. Christie, W. C. Hellyer

Three autogenous grinding flowsheets were considered as follows: 1) Primary autogenous grinding of a -8-in, primary crusher discharge to produce a product suitable for second stage pebble milling, or a flotation feed product in a single stage of grinding. 2) Intermediate autogenous grinding in which +4-in. rock media is screened from the primary crusher discharge and employed as grinding media to grind a tertiary crusher product to flotation feed size in a single stage.

Jan 8, 1972

FROM north to south activity is picking up through- out the Labrador Trough-already shown to be one of the world's great iron ore provinces. Center of current activity and interest lies in the mid-southern part of the trough as drills, equipment, and . . . money start to pour into the area near Mt. Wright and Wabush Lake. First major announcement in the area came early this spring when J&L and CCI outlined an estimated billion-ton deposit for "future" operations. Later impetus came from rumored railway for US Steel's Quebec Cartier projects in the Mt. Reed area slightly to the south. As this issue went to press US Steel's request for bids on railway and hydroelectric construction, plus IOCC's decision to step up the time- table on its program in the Wabush Lake area east of Mt. Wright, triggered a flurry of other announcements involving many of the top U. S. and Canadian iron ore firms. Do not look for most of these place names in the average atlas . . . they aren't there yet, but they soon will be.

Jan 6, 1958

By J. C. McCarthy, J. B. Stone

AT Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. LOCATION The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in the world. Another famous old silver district, Sombrerete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo station on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo is surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proano hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proa[n]o hill are the Fresnillo mines, and it is marked now by a great gash cut by gloryhole mining. HISTORY According to an account written in 1834 by Francisco García, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between Zacatecas and Sombrerete. Little is known of the earliest mining at Fresnillo. which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notable active in 1751 under an administrator named Murguía, who left detailed notes describing them. In 1757, however, the mines became inactive because of difficulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresnillo became the property of the State of Zacatecas because the interest of Governor García had been aroused by the long disregarded notes of Murguía. Under Garcia's energetic leadership the mines were reopened, and silver production began in 1832 in spite of serious difficulties, including abnormal rains and an epidemic of cholera. In 1833 English capital was sought to allow installation of steam-driven Cornish pumps at the two principal shafts and to build the great hacienda de benefacio (the present Proano hacienda). The company formed in 1835 (Cia. Zacatecano-Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1942

By Robert W. Hunt

The first pump of this character, made by H. R. Worthington, and, so far as the writer is informed, the first and only one of this kind ever constructed, is now in daily use in the above-named works. The water-pressure necessary for the working of the hydraulic machinery of this plant had been supplied, up to the time of the building of this pump, by two Worthington Duplex High Pressure Pumps, having steam-cylinders of 20 inches diameter and 12-inch stroke, with water-plungers of 71/2 inches diameter; eight inlet and eight outlet valves of 24 inches diameter, and pumping into a 6-inch pipe. These pumps required a large amount of steam, and, in consequence of the various additions to their duty, their capacity became far short of the work required. In preference to putting in another engine of the same class, it was decided to accept Mr. Worthington's proposition to build the compound one under description, he guaranteeing that it should be equal to the demands of the works, and at the same time cause a saving of from 5 to 6 tons of coal per day from the amount required to run the two old pumps. The new engine has been in operation about one month, and so far has exceeded the most sanguine expectations. It consists of two high-pressure cylinders of 21 inches and two low-pressure ones of 363/8 inches diameter, by 36-inch stroke, with water-plungers of 961/2 inches diameter. There are two air-pumps of 20 inches diameter by 18-inch stroke; the condenser being 24 inches diameter by 60 inches high. Both cylinders are jacketed with wood and felt, and the low-pressure cylinder also with live steam. The high and low pressure steamcylinders are in line and immediately adjoining each other, while the inconveniences attending an internal stuffing-box are avoided by having two piston-rods for each of the low-pressure cylinders, running through stuffing-boxes on the outside of the smaller high-pressure ones. The steam-valves are very ingeniously designed balanced