Search Documents

By E. T. Turkdogan, L. S. Darken, R. G. Olsson, H. A. Wriedt

Several aspects of the calcination of Michigan limestone were investigated: the rate of calcination of limestone spheres with diameters from 1.8 to 14 cm at temperatures from 800° to 1200°C by a thermogravimetric method; the temperature profile across limestone during calcination; the excess pressure developed in the interior of the stone during calcination; the pore surface area, pore volume, and effective gas diffusivity in burnt lime; and the microstructure of polished and fracture surfaces. It is found that, over a wide range of experimental conditions, the difference between the surface and center temperatures remains essentially unchanged during the latter half of calcination. From the rate of weight loss after about 50% calcination, the value 0.00126 cal per cm sec degree is found for the effective thermal conductivity of burnt lime. From the excess internal pressure measurements, i.e., 0.4 to 6 cm Hg at 800° to 1200°C, the permeability of burnt lime is estimated to be within the range 8 X 10-' to 5 X 10' sq cm. With increasing temperature and time of calcination, the pore structure of burnt lime coarsens as indicated by a decrease in the pore surface area, pore volume, and an increase in the average pore size. For the temperature range 600° to 835°C the ratio (effective gas diffusivity/molecular diffusivity) is about 0.18.

Jan 1, 1974

By J. P. G. Farr, R. Brownsword

THE role of solute segregation in the formation of cellular solidification substructures in tin and its dilute alloys is well-established, see, e.g., Ref. 1. Segregation has been shown to persist during cooling, enabling solidification structures to be studied from sections taken at some distance behind the interface. In the present work, a single crystal of commercial nickel, 99.965 pct, was examined in this way. The crystal was cut from the center of a rod given a single pass in an electron beam floating zone melter. Polished sections of a nickel specimen taken normal to the growth direction showed a very fine precipitate phase, the distribution of which varied over the section. The identification of the phase proved difficult because of the small amount present and the small particle size, about 1 p: but it was shown by probe microanalysis to contain only nickel and oxygen in detectable concentrations and was probably nickel oxide, NiO. Bulk analysis of the material before melting showed there to be only 3 to 4 ppm of oxygen present, thus demonstrating a very considerable segregation concentration effect. In some areas of the section the precipitate formed a discontinuous hexagonal network suggesting decoration of the cellular boundaries known to be present in the sample2 whereas in a restricted region the precipitate formed small clusters. Occasionally it could be seen that the clusters were at the intersections of an hexagonal network of cellular dimension. It was suggested3 that this was the result of enhanced segregation to the cell boundary intersections whereas general cell boundary segregation was insufficient to give a precipitate. Enhanced nodal segregation has since been demonstrated in a number of systems.1, 4-8 The development of a suitable electrolytic etching technique (perchloric acid 20 pct v/v; ethyl alcohol 70 pct; glycerol 10 pct; current below electropolishing plateau; 1 to 2 sec etching) suggested the association of the phase with regions of solute segregation (where ko < 1); in these regions anodic attack produced grooves or depressions. In a study of the variation of solidification substructures with degree of constitutional supercooling, Biloni et a1.&apos; appear to have used standard growth conditions and varied the solute concentration. They were able to produce in a series of individual tin crystals examples of substructure ranging from planar interface through various cellular structures to den- Fig. 1—Electroetched section taken normal to the rod axis; the center of the rod lies to the left and the periphery to the right of the micrograph. The variation of structure across the section is evident. Magnification 60 times. drites. It was possible in the present nickel crystal to observe a continuous range of substructures varying with degree of supercooling across a single section as shown in Fig. 1. Growth rate, 13 mm per min, and temperature gradient were essentially constant; the variation in structure is thought to be due to a radial gradient in solute concentration ahead of the solid interface. The liquid at the interface is likely to have been richer in solute toward the periphery of the zone, the result of curvature of this interface. The type of substructure was seen to vary with increasing constitutional supercooling as follows: a) region free of precipitate. top left, Fig. 1: 6) region of nodal precipitates which became arranged in hexagons on passing from the center of the rod: c) irregular hexagonal cells with incomplete boundary precipitation; d) regular hexagonal cells of decreasing size with complete boundary precipitation. Fig. 2 shows the transition from stage 6 and Fig. 3 shows the structure in stage d. Within stage 0, the range of conditions over which irregularly positioned nodes occur appears to be small and the nodes are soon recognizable as taking up positions at the intersections of an hexagonal network as the supercooling increases.

Jan 1, 1970

By Oswald J. Heinrich

During the last twenty years much has been done to investigate and define the Mesozoic formatibn of the United States along the Atlantic States, as well as in&apos; the Territories. The investigations of Professors Hitchcock, Emmons, Hayden, H. D. Rogers, and those now in progress in connection with the geologicd surveys of Penn-

Jan 1, 1879

By Raymond Edmundson

BARITE probably was first mined in the United States in 1845, when a small deposit was operated in Prince William County, Virginia1. The next state to produce barite was Missouri, and according to Weigel2, mining began about 1860. Virginia was the leading producer during the early period of barite mining, but by 1893, Missouri was producing almost an equal amount3. From this date, Virginia, although not the leading producer, furnished large quantities of crude barite until oper-ations gradually declined about 1907. Since 1910, there has been only one producer in Virginia. It is not known when barite was discovered in each of the Virginia areas (Fig. 1), but it is reliably reported that mining on a commercial scale began in Campbell-Pittsylvania counties about 1874; Smyth County in 1877; and in the Russell-Tazewell area about 1890. Barite is widely distributed in Virginia, occurring in nineteen counties. The localities that contain material of some economic value have been grouped into six areas (Fig. 1), each designated by the county or counties in which the barite is found. As many of the smaller areas show a similarity in geologic occurrence, they will be considered in this paper as two major groups; namely, Appalachian Valley and Piedmont Province. The first group, which includes the barite deposits of Russell, Tazewell, Smyth, Botetourt and Roanoke counties, lies northwest of the Blue Ridge and its foothills and southeast of the Appalachian plateaus. The other group includes deposits from the Blue Ridge on the west to the western margin of the Coastal Plain, in Campbell, Pittsylvania, Bedford, Grayson, and Fauquier counties.

Jan 1, 1936

By W. S. Potter

The proportions of manganese and carbon in manganese steel are familiar to all…

Jan 1, 1915

By Richard L. Stowe

Four NX-diameter holes were diamond-drilled in competent granite. Samples of the recovered core were used in laboratory tests. A borehole, plate-bearing device known as a Goodman jack was used to perform load deformation tests on the rock in the core hole. The majority of samples used in the laboratory tests were taken from depths in the hole at or within 5 ft of those at which the plate bearing tests were made. Borehole camera records, compressional and shear wave velocities, and densities were measured. Dynamic elastic constants were computed for the in-situ material, while comparative data (except camera records) were obtained in the laboratory. These data were examined to evaluate the significance of the in-situ modulus of deformation (Ed), the value computed from Goodman jack tests. Average test results show an excellent correlation between in-situ and laboratory data. The ratio of laboratory to field deformation modulus ranges from 9.82 to 7.21 for 3,000 and 9,000-psi stress levels, respectively. The dynamic modulus ratio, ED field/Ep lab, is 1.02; the compressional wave velocity ratio, V8 field/V8 lab, is 0.94; the shear wave velocity ratio, V, field/V, lab, is 1.12; and the density ratio, field [y/y] lab, is 0.95.

Jan 1, 1973

By J. R. Campbell

IN order to discuss the subject intelligently, it will be necessary to touch briefly on the forms in which sulphur is supposed to exist in coking coal to be carbonized in beehive or byproduct ovens. Sulphur is known to exist in coal as sulphides and sulphates, as can be determined experimentally. Then there is the so-called organic sulphur, i.e., sulphur in combination with the carbon, hydrogen, and oxygen of the coal, about which much has been written, but nothing definitely proven in an experimental way. In fact, so far as we know, there never has been developed a satisfactory and conclusive method in the laboratory for the direct determination of organic sulphur. For most coking coals, it can be safely assumed that the preponderance of sulphur is in the form of pyrite (FeS2). When exposed to comparatively low temperatures during the coking process, it loses its sulphur according to the following chemical reaction: 7FeS2 = Fe7S8 + 6S. It will be seen, therefore, that six out of the 14 atoms of sulphur (or 42.8 per cent.) are expelled, or volatilized. Fe7S8 remains in the coke as pyrrhotite, or magnetic sulphide of iron; this accounts for the highly magnetic properties of the powdered coke. A more commonly accepted reaction is FeS2 = FeS + S, in which the straight sulphide of iron is produced with 50 per cent. volatilization of sulphur. In the beehive methods of coke making, air is introduced in sufficient amounts to carry on the distilling and the coking processes, and the sulphur is oxidized along with the other volatile products: First, into sulphur dioxide (SO2), known by the pungent and suffocating odoremitted from the trunnel head; second, into sulphuric anhydride (SO3); and, finally, into sulphuric acid, as it comes into contact with the air and moisture. In a properly regulated draft on a beehive oven, there is never complete combustion of the gases. In other words, the coking process should be carried on in a reducing atmosphere, and a low-grade producer gas kept issuing from the trunnel head. For coals of about 30 per cent. volatile matter, the ratio of air to gas is 3 ½ to 1. In complete combustion, the ratio is 6 to 1, producing an extremely high temperature

Jan 1, 1916

By Lawrence Wright

THE occurrence of gold, gold-silver, silver-lead-zinc ores in the post-Cambrian sediments in the Black Hills of South Dakota, and their genetic relationship to the Tertiary intrusives, is well known and accepted, but the occurrence of gold in the pre-Cambrian rocks at the Homestake mine, which underlie this Tertiary gold mineralization, has given rise to differ-ences of opinion as to the period of major gold introduction into the older rocks. Fig. 1 illustrates. the distribution of mineralization along the axis of the Tertiary uplift in both pre-Cambrian and post-Cambrian rocks. The following possibilities have been presented: 1. The Homestake gold deposit was formed in pre-Cambrian time and the deposits in the overlying Cambrian sediments formed during Ter-tiary time. 2. The Homestake lode existed at the beginning of Cambrian time, but was enriched by the passage of Tertiary auriferous solutions. 3. The Homestake lode was represented by pre-Cambrian quartz-chlorite sulfide mineralization, very low in gold content and the gold superimposed on the older nearly barren mineralization during the Ter-tiary metallogenic epoch. 4. The sulfides and sulfarsenides as well as gold were deposited in both pre-Cambrian and post-Cambrian rocks during the Tertiary period. Those favoring the first proposition feel that the question is pretty well settled, while the proponents of the second theory are more flexible in their view, feeling that the amount of gold introduced in either period is still an open question. The third and fourth theories, with some modifi-cations, are supported by the proponents of the Tertiary theory, who feel that the evidence strongly favors that period. The following pages are intended to present the evidence and to give the reaction of various observers with my own comments and conclu-sions; also, the accumulated facts of observation gathered over a period of close association with the area under discussion, beginning in 1919.

Jan 1, 1936

By S. A. Allison, N. P. Finkelstein

After a brief consideration of the properties of zinc sulfide minerals, their flotation characteristics, and their reactions with thiol collectors, the literature on the activation of the minerals by cupric ion, their deactivation by cyanide, and their depression is reviewed in detail. The distinction between deactivation and depression is stressed. The contradictions in the published results and theories are discussed and attempts are made to resolve them. It is concluded that, whereas all aspects of the subject require further investigation, the study of depression is most likely to yield benefits in practice.

Jan 1, 1976

By T. L. Joseph

THE committee appointed to investigate the application of oxygenated air to the blast&apos; furnace believes, after a careful study of the problem, that this enriched air will increase hearth temperature, tonnage, flexibility of operation, and quality of pig iron made, and that fuel consumption will be decreased. These improvements are supported by theoretical evidence; but a practical trial of the process is necessary to establish more definitely the magnitude of benefits realized. The commercial application, however, may profitably be preceded by a test on a smaller scale. A small furnace will, in general, respond to the enriched air in the same way as a commercial furnace and the magnitude of the benefits to be gained from varying additions of oxygen can be fairly well established at relatively little expense. A new experimental furnace, being built jointly by the Bureau of Mines and the University of Minnesota, at Minneapolis, will have a capacity of about 6 tons and will riot require more than 700 cu. ft. of natural air per minute. Its hearth is 36 in. in diameter and its height about 32 ft. Enough oxygen to enrich the blast to the extent recommended by the committee can be obtained from a small oxygen unit. It might even be cheaper to perform preliminary experiments with tanks of oxygen obtained from regular, dealers. A procedure in making the test that suggests itself is to start with operation on normal air; then to use blast, enriched in several steps. Systematic temperature measurements of the tuyeres, slag, and metal would reveal any changes in hearth temperature. When these changes become large enough, the burden may be gradually increased to just within the breaking point and the furnace brought back to normal, if possible, by the addition of oxygen. Such a test would show what might be expected in the way of a decrease in fuel consumption and the time taken to "straighten up" the furnace by means of oxygen. The new furnace at Minneapolis is so equipped that the furnace process can be observed from the stock line to the iron notch. We have been taking gas samples at various elevations in the furnace to study combustibility of the fuel and the reducing power of the gas. If either of these is affected by removing inert nitrogen, the change can easily be measured.

Jan 11, 1924

By Richard M. Foose

Five miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. Geology Lower Cambrian Antietam quartzite and the Rilontalto quartzite, stratigraphi-cally older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65" to vertical. The clay crops out at an elevation of about 1000 feet. Origin and Character The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there Are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about loo ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: SiO2, 67.05 per cent; Al2O3, 22.27; Fe2O3, 0.40; CaO, 0.00; TiO2, 1.05; MgO, 0.52; Na20, 0.04; K2O, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1948

By Richard M. Foose

Five miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. Geology Lower Cambrian Antietam quartzite and the Rilontalto quartzite, stratigraphi-cally older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65" to vertical. The clay crops out at an elevation of about 1000 feet. Origin and Character The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there Are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about loo ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: SiO2, 67.05 per cent; Al2O3, 22.27; Fe2O3, 0.40; CaO, 0.00; TiO2, 1.05; MgO, 0.52; Na20, 0.04; K2O, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1948

By B. L. Averbach, M. Cohen, C. H. Shih

The isothermal formation of martensite is studied in Fe-Ni-Mn and Fe-Mn-C alloys under conditions where the athermal transformation is completely avoided, there being no martensite present at the beginning of the isothermal reaction. The initial rate of martensite formation is extremely low under these conditions, but it increases greatly as soon as some martensite is formed. It appears that true initial characteristics of the isothermal reaction can be studied only in samples wherein the formation of martensite on cooling is completely eliminated. THE phenomenon of isothermal martensite formation is well established1 -" but the observations have been made in the presence of varying quantities of athermal martensite. Complete avoidance of athermal martensite and the formation of martensite under pure isothermal conditions have been reported by Kurdjumov and Maksimova2 in an Fe-Ni-Mn alloy (23 pct Ni, 3.4 pct Mn, and the balance Fe) and have been confirmed by recent experiments of Cech and Hollomon in a similar alloy. In each case, the isothermal transformation rate was a maximum at the beginning of the transformation and decreased as the reaction proceeded. These initial transformation rates were used by Fisher7 for the confirmation of calculated nucleation rates based on classical nucleation theory extended to include the effect of elastic strain energy. Cech and Hollomon have admitted, however, that up to 3 pct martensite formed on cooling in their samples and thus was present at the initiation of their isothermal runs. In this paper, experiments on similar alloys are described, except that care was taken to remove the incidental martensite developed at the surface prior to the isothermal reaction. It is shown here that the reaction rate at the beginning of the strictly isothermal reaction is very low. As soon as some detectable amount of martensite is produced, the transformation rate increases rapidly but ultimately decreases as the reaction proceeds. When martensite is allowed to form isothermally in the presence of about 2 pct of prior martensite, the apparent initial reaction rate is a maximum and corresponds to the observations of Kurdjumov and Maksimova and Cech and Hollomon. It is evident that the cooperative nature of the martensitic reaction results in a significant stimulating or autocatalytic effect on the isothermal reaction rate. Experimental Procedure The chemical compositions of the alloys used in this investigation are listed in Table I. The Fe-Ni-Mn alloys A and B were melted in an induction furnace, cast into ingots 2 in. diam by 4 in. long, and forged into % in. diam rods. The manganese steel (alloy C) was melted in an arc furnace and cast into ceramic molds 1/4 in. diam by 5 in. long. The rods were sealed in evacuated Vycor tubes and homogenized at 1175" to 1200°C for 50 hr. The long homogenization resulted in some manganese loss from the surface, producing a thin layer of transformed material. This surface layer was removed by grinding and the specimens were then swaged to 0.050 in. diam wire. Measurements of electrical resistance were made with a Kelvin double bridge to follow the course of the martensitic transformation. A small permanent magnet was also useful in scanning an entire specimen for small localized quantities of martensite. This test is almost as sensitive as the electrical resistance method in detecting the presence of martensite (which is ferromagnetic in these alloys) and it was especially useful in deciding whether a specimen was completely free of martensite. The wire specimens (0.050 in. diam by 2.5 in. long) were sealed in evacuated tubes and austenitized for 5 min at 1150°C. The specimens were quenched into water and, unless otherwise stated, stress-relieved for 1 hr at 650 °C in order to induce greater uniformity in the subsequent martensitic transformation. As dem-

Jan 1, 1956

By M. F. Trice

PYROPHYLLITE is a hydrous aluminum silicate (Al2Si4O10(OH)2)1 that occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs&apos; scale.1 The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey,2 contain pyro-phyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, "are noticed in but small quantities to the extent they might occur as accessory constitu-ents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent.

Jan 1, 1940

By J. B. Hess, C. S. Barrett

TO reach equilibrium between different phases in cobalt-rich alloys requires prohibitively long annealing cobalt-richalloystimes when temperatures are below about 700°C. The fact that a transformation from face-centered cubic to close-packed hexagonal readily tered takes place at temperatures below this in the cobalt-rich solid solutions is not an indication that thermally activated processes occur at an appreciable rate, for the transformation is well established as martensitic in nature. Wide divergence between heating and cooling experiments and high sensitivity to prior heat treatment make it difficult to judge temperatures of equilibrium between the phases.&apos; One object of the present work was to see if the information object of on the relative stability of phases could be gained by substituting plastic deformation for thermal agitation. Procedures were worked out that led to the determination of a diffusionless type of phase diagram, which represents the temperature of of phase equal stability for phases of the same composition, and the technique was applied to the Co-Ni system. Another object of the work was to see whether or not deformation would generate frequent stacking faults when these were thin lamellae of quentstackingfaultsa phase having higher free energy than the parent phase. The alloys were prepared in 80 to 100 g melts from cobalt (with metallic impurities estimated spectrochemically as follows: Ni, 0.05 pct; Fe, 0.001 pct.; Mg, Si, Cu, Cr, Al, < 0.001 pct) and Mond Car-bony1 nickel (with Fe, 0.05 pct; Si, 0.003 pct; C, 0.61 pct.; Cu, 0.001 pct; Co, Cr not detected, < 0.01 pct). The metals were melted in pure Al2O3 crucibles. An atmosphere of argon, that had been purified by passing over hot magnesium chips, was used for the alloys that, by analysis of the portions of the ingots actually used, were found to contain 15.3, 25.7, and 35.0 pct Ni, and vacuum melting (after degassing) was used for those containing 29.4 and 31.5 pct Ni. After induction melting the alloys were allowed to solidify in the crucible, and slices % in. thick x ½ in. in diam were annealed 12 hr at 1350°C for homogenization. These same specimens were used throughout the series of experiments, with annealing treatments of 4 hr at 900°C in purified hydrogen followed by furnace cooling, alternating with the deformation and X-ray tests discussed below. Results Spontaneous transformation was observed on cooling to room temperature in all alloys containing 29.4 pct Ni or less and by cooling the 31.5 pct alloy to — 195°C but was not observed in the 35 pct alloys after cooling to —195°C. These results are in satisfactory agreement with the cooling experiments of Masimoto.4 From these data it is clear that the temperature of beginning transformation M,,, drops to 20°C with the addition of about 30 pct Ni. The test for spontaneous transformation was metallographic. Specimens were thermally polished by annealing 10 hr in hydrogen at 1350°C, then furnace cooled; if trans- formation had occurred there were relief effects visible on the thermally polished surfaces. These markings were narrow straight lines, usually resolvable at high magnification as clusters of fine lines that resembled slip lines. It was concluded that they resulted from displacements on (111) planes, for the number of directions in individual grains often reached but never exceeded four, and lines could always be found parallel to the thermally etched (111) boundaries of annealing twins. The markings were thus consistent with the idea that the transformation occurs by (111) plane displacements (Shockley partial dislocations moving on (111) planes). This was further confirmed by X-ray tests for stacking disorders. Using an oscillating crystal technique previously employed to detect strain-induced faulting in Cu-Si alloys," streaks indicative of the stacking faults were looked for and found on X-ray films of the spontaneously transformed 25.7 pct Ni alloys, as expected by analogy with Edwards and Lipson&apos;s results on pure cobalt." The streaks were much intensified after rolling at room temperature. Transformation induced by plastic strain was investigated as a function of alloy composition and temperature of deformation. A series of tests was made to determine suitable straining and X-raying techniques. Filing was found inferior to abrasion in converting cubic samples to hexagonal, and abrasion was less effective than peening in producing smooth unspotty Debye rings in the X-ray patterns. Because the diffraction lines were broad, Geiger-counter spectrometer records of filings were less sensitive in revealing small amounts of transformed material than X-ray patterns recorded on films in a small diameter camera. After these exploratory tests the following methods were adopted. Specimens that had been annealed at least 4 hr at 900°C and furnace cooled were mounted in a block of aluminum, brought to temperature, and peened thoroughly with a mullite pestle preheated to the same temperature. The specimens were then quenched to room temperature. In peening, a circular area of % in. diam was given 500 blows. A few control tests showed that an additional 1000 blows did not detectably change the proportions of the phases present. The amount of transformation was judged by X-ray reflection patterns from the peened surface, using the innermost four lines of the cubic and the hexagonal patterns with filtered CoKa radiation,

Jan 1, 1953

By Robert U. King, John W. Vanderwilt

THE Climax molybdenite deposit in Lake County 100 miles southwest of Denver is located in the central part of the mineral belt extending north-easterly across the state. Principal geographic features and geology are shown on Fig. 1. The first period of molybdenite mining, which began in 1918, ended in April 1919 because of limited demand and a price drop to about 724 per lb. During this time the ore came from the Leal level and surface outcrops at a higher elevation. Rate of mining was 250 tpd and several million tons of ore averaging 0.7 pct molybdenite were developed. Since April 1924, when the second period* began, Climax Molybdenum Co. has been the only operating company. Production in 1924 was 400 tpd and finding ore was a continual problem. When the White tunnel was extended, however, further ore was encountered. The orebody was thought to be tabular until 1926, when B. S. Butler recognized the relation of the developed ore on the Leal and White levels to a central area of fine-grained hydrothermal quartz, and by 1929 diamond drilling had blocked out indicated ore reserves in excess of 100 million tons.

Jan 1, 1955

By W. D. Robertson

SINCE the comprehensive paper of Moore, Beckin-sale, and Mallinson,&apos; little consideration has been given to the mechanism of mercury stress cracking of copper-base alloys, apart from extensive work on metallurgical and fabrication variables employing mercurous nitrate as an evaluation test. However, with the phase diagrams now available and the recent considerations of interfacial tension at grain boundaries, developed by Smith,2 it appears that the elements of a detailed solution to the problem are available. The facts that require explanation are: 1—Pure copper is not embrittled by mercury, with or without an applied or residual stress. 2—Cu-Zn and other copper-base alloys, in excess of some undefined solute concentration, are embrittled provided an external or residual stress is acting; cracking is not observed in the absence of stress. 3—The path of fracture is invariably intergranu-lar. 4—Copper and copper-base alloys do not dissolve readily in mercury at room temperature.&apos; Consideration of the Cu-Hg phase diagram% hows that, at room temperature, solution of copper in mercury is probably limited by the formation on the surface of a microscopically thin layer of inter-metallic compound, CuHg, having a very limited range of solubility which effectively restricts diffusion of copper and mercury. But, above 150°C (the highest peritectic temperature) copper solid solution is in equilibrium with a liquid Hg-Cu solution and, consequently, copper should dissolve freely in a large volume of mercury with the formation of an equilibrium dihedral angle at grain boundaries in contact with the liquid phase. Depending on the magnitude of this angle, mercury will or will not penetrate the solid phase along grain boundaries and spread over grain faces. Thus the measurement of the dihedral angle of grain boundaries in equilibrium with the liquid phase above 150°C should indicate whether copper is intrinsically resistant to embrittlement by mercury. In view of the fact that mercury is appreciably soluble in copper, it may also be anticipated that diffusion of mercury will take place at higher temperatures in the absence of the intermetallic compound and possibly at a more rapid rate along grain boundaries than through the grains, resulting in a Cu-Hg alloy of unknown properties. In the case of brass, the ternary system Cu-Zn-Hg is involved and, from the resistance of brass to general solution in mercury at room temperature, it is probable that a compound of limited solubility range also exists, similar to the binary Cu-Hg sys- tem. Also, compared with copper, a change in the dihedral angle at grain boundaries in contact with mercury may be expected to result from the addition of zinc to copper. The preceding generalizations appear to be confirmed by the following experiments. Experimental Results Oxygen-free copper wire, annealed at 700°C for 3 hr in copper foil, was immersed in mercury at 170°C, with and without an applied stress. After 24 hr immersion, specimens which were spring loaded to a nominal stress of 10,000 psi had not failed, and there was no apparent embrittlement as indicated by a 180" bend around a diameter approximately equal to the diameter of the wire (0.125 in.) : General solution of the surface had taken place, indicated by a change in diameter of the wire, and the resulting structure of the surface is shown in Fig. 1. It is apparent that angles have developed at grain boundaries and examination at a high magnification indicates that the angle is in excess of 120°, completely excluding penetration of mercury. In view of the measurements made by Smith n the

Jan 1, 1952

By H. K. Najarian

This paper describes recent development work on the Wheaton-Najarian Vacuum Condenser for Zinc at Josephtown Zinc Smelter, wherein, to dissipate the heat of condensation, the "airlift" action of gases bubbling through the molten zinc in the condenser is utilized to circulate the zinc through an outside "cooling well" and cooling it continuously. AN earlier paper1 gave an account of initial development of the Wheaton-Najarian Vacuum Zinc Condenser at the Josephtown Zinc Smelter of the author&apos;s company. This paper is a progress report of further development work over the years directed toward improving the efficiency and increasing the capacity of the condenser. In this type of zinc condenser, zinc vapor with accompanying noncondensable gases from electro-thermic zinc smelting furnaces is passed upwardly through a mass of molten zinc confined in a refractory-lined U-tube. The zinc vapor condenses in the molten zinc and the noncondensable gases are drawn out of the condenser by suction applied over the surface of the molten zinc. The heat of condensation of zinc, amounting roughly to 1000 Btu per lb of zinc condensed, is absorbed by the molten zinc and, in turn, is dissipated continuously to keep the temperature of molten zinc in a range to permit effective condensation. At the time of publication of our first paper, we had at Josephtown Smelter five units of 69-in.-bore metal furnaces and one larger metal furnace having 96-in. bore. Each 69-in. metal furnace had a condenser with 22-ft overall length. The 96-in.-bore furnace had a condenser with overall length of 31 ft. Condensers were of circular cross section, with corrugated steel outer shell and carborundum lining. Diameter of these condensers was 32 in. inside the refractory lining. Molten metal in the con- denser was kept cool by spraying cold water on the outside of the condenser shell. Under good operating conditions, 22-ft condensers produced some 12 tons of metal per day; and the 31-ft condenser, about 22 tons. When the furnaces produced zinc vapor at higher rates, invariably the condenser temperature would rise to levels where excessive blue powder would form and accumulation of accretions in the condenser would be accelerated. We found that, with the system of cooling in use, we had to provide heat-exchange surface of some 150 sq ft to condense 1000 lb of metal per hr with reasonable efficiency. The wall of the condensers was made up of 5/8-in.-thick corrugated-steel shell having next to it several layers of mica and inner refractory lining of special carborundum shapes to fit the corrugation in the steel shell, and having a minimum thickness of about 2 in. Relatively low rate of heat transfer through the thick condenser wall and slow internal circulation of the molten zinc limited the rate of heat exchange between hot metal within the condenser and the cold water flowing over the outer steel shell. The thickness of the condenser wall was about minimum that we considered suitable for continuous operation. As we learned to operate the electrothermic furnaces with higher power input, producing zinc vapor at higher rates, it became apparent that we needed condensers having larger heat-exchange surfaces. Our 96-in.-bore furnace had 6 single-phase power circuits with transformers rated at 500 kva each and normally good for power input of 3000 kw.

Jan 1, 1959

Jan 1, 1969

By G. E. Goodspeed

THE Cornucopia gold quartz veins form a parallel vein system traversing meta-morphic and granodioritic rocks. Field and petrographic evidence suggests that metasomatism has played an important role both in the emplacement of the grano-diorite and in the formation of the veins. Structurally the veins appear to be related to the major tectonic features of the Wallowa Mountains and to be narrow shear zones rather than filled fissures. Petrographic studies indicate a complex history of formation starting from initial alteration along fractures or joints followed by recurrent fracturing and a quartz-forming stage,-and closing with continued shearing and microbrecciation, which permitted the upward percolation of the later ore-forming solutions. The precipitation of ore minerals from these solutions formed ore shoots. Postmineral effects include the injection of Tertiary basaltic dikes, a slight amount of cross faulting, and some movement along the planes of the veins as well as oxidation. INTRODUCTION Cornucopia is in the southeastern part of the rugged Wallowa Moun-tains of northeastern Oregon. It was founded over 50 years ago following the discovery of its system of gold quartz veins. The major veins are roughly parallel and dip into the western side of Pine Valley, which drains the southern slope of the range. Previous operations had cut the upper portion of four major veins with two tunnels over 1000 ft. apart, when the present operating company drove a third tunnel, called the Coulter, at the level of the valley over 1000 ft. lower to intersect the most easterly major vein at over 6200 ft. from the portal.

Jan 1, 1939