Search Documents

Fred D. DeVaney (Magnetic Roasting of Iron Ores, P. 1219) has presented several other AIME papers, all of them concerned with grinding and concentrating problems. He is chief metallurgist, Pickands Mather & Co., at Hibbing Minn., after working for the U. S. Bureau of Mines at Tuscaloosa, Ala., and Rolla, Mo., as a junior metallurgist and a metallurgist. DeVaney started as a research metallurgist with Pickands Mather in 1942. He set up the first laboratory in the Lake Superior district devoted to taconite concentra¬ [ ] tion, his major interest. He has been an AIME member since 1923, holding various offices, including the first presidency of the Minnesota Section. DeVaney has a Bachelor's in Mining, and Master of Science earned at the University of Alabama in 1924. He is a member of the Engineers Club of Northern Minnesota and plays golf for relaxation and enjoyment.

Jan 1, 1952

By T. Cuscino, D. D. Lane, C. Cowherd, T. E. Baxter

Three types of commercially-available dust suppressants, commonly used in the surface mining industry to control fugitive particulate emissions from unpaved roads, were tested in the laboratory for cohesive strength and resistance to reduced effectiveness by large water addi¬tions. Results indicate that each product tested varies in cohesive strength with a range of 34-300 kPa (5-44 psi). Total cohesive strength depends on the aggregate moisture content and the means by which the sample is dried. Results show that laboratory testing can be used as a decision¬making tool concerning the type of dust suppressant for a particular mining operation. Also, the road surface aggre¬gate moisture content u critical to successful dust suppres¬sant performance. Large water additions to the aggregate road surface after initial suppressant application can pro¬duce nondesirable results. A modified wet sieving analysis is presented to test the effect of water addition.

Jan 1, 1984

By R. J. P. Lyon

It is usually assumed1,2 that ore deposition is relatively slow, taking place over tens of thousands of years. Yet many syntheses and phase changes can be completed in the laboratory in a matter of hours, under essentially the same pressure and temperature conditions to be expected in nature. Much has been written about geothermometry, and Ingerson's recent summary2 an hardly be surpassed. Rather than review the whole field, this article will deal specifically with diffusion rates in solid solutions* of the sulfide minerals. In the study and application of temperature-indicating phenomena to problems of ore genesis, the time factor has often been neglected. In the particular case of sulfide systems, the speed of unmixing and diffusion of the constituent phases in the solid solutions has seldom been considered when laboratory data are applied to the genesis of natural sulfide ores. Chalcopyrite and Bornite Intergrowths: Chal-copyrite and bornite are copper iron sulfides often found in association. In many ores the individual grains appear to have mutual boundaries, but bladed intergrowths are quite common. Early workers in the field, " deduced that while these patterns could have been formed by replacement, they could be experimentally reproduced from the unmixing of solid solutions of the two previously homogenized at 475°C. Much of the ore from Roan Antelope mine in the Rhodesian Copper Belt exhibits these bornite-chalcopyrite intergrowths, from which it has been deduced that the ores could have been subjected to a minimum temperature of 475°C. In several recent interpretations,' this temperature rise has been considered to result from a regional metamorphism of an original syngenetic copper-bearing sediment. The same temperature rise to 475 °C was suggested from similar intergrowths in the sulfide- • The general subject of solid solution in structurally similar minerels is treated in many texts'. :' ' and will not be further elucidated. bearing ore from the Happy Jack uranium mine8 on tile Colorado Plateau, although this temperature had a different origin. In 1931 SchwartzV etermined that 475°C represented the unmixing temperature of his bornite-chalcopyrite solid solutions but, more important, that the characteristic intergrowths of bornite and chalcopyrite could be preserved only if the solid solution were chilled quickly to room temperature. This significant corollary has been almost completely neglected by both Davis and Miller.7,8 By suitably decreasing the cooling rate, Schwartz found that the original pattern of the intergrowth was reformed (Fig. 1). The cooling rate was critical. In cooling from 475°C to room temperature in

Jan 1, 1960

By H. M. St. John, T. Rynalski, G. K. Eggleston

Maintaining a satisfactory structure in brass and bronze castings has always been a foundry problem of great practical importance. While metallurgists and scientific investigators have not entirely ignored this matter, it has received less of their attention than has been given to iron, steel and the wrought copper and aluminum alloys. Investigation in this field has probably been discouraged to some extent by the complicated nature of the alloys involved. Hundreds of alloys are in more or less common use, most of them containing copper, zinc, lead and tin in widely varying proportions. They also contain appreciable percentages of iron and antimony as impurities, and often phosphorus, which has been added as a deoxidizer and fluidifier. Small amounts of sulfur are usually present. It is not uncommon to find nickel, sometimes in rather substantial quantities. Traces of other metals are frequently present. So complicated and variable a mixture obviously offers difficulties in any investigation of the various factors that influence the structure and other properties of the casting. Incipient Shrinkage Bolton and Weigandl have called attention to a type of structure characterized by intercrystalline fissures and large dendritic crystals which are frequently tarnished to an orange or reddish brown color. This intercrystalline porosity they term "incipient shrinkage" and attribute to the presence of carbon monoxide in the atmosphere under which the metal was melted. The defective structure to which Bolton and Weigand refer has become a brass-foundry problem of major importance, because it occurs with distressing frequency in leaded brasses and bronzes when these are melted in a neutral or reducing atmosphere. Since the electric furnaces, now coming into general use in brass foundries, normally operate with such an atmosphere and, in fact, depend upon it in part

Jan 1, 1930

By T. F. Baily

During the period of the war, in both this country and Canada, a number of attempts were made to make pig iron from steel scrap in the electric furnace, and a considerable tonnage of white pig iron was produced, the silicon and manganese additions being made with ferroalloys; but it is believed that the experiments conducted. at Canton, Ohio, in

Jan 1, 1930

By Pierre I. Desré, Donald T. Hawkins, Ralph Hultgren

The torsion effusion method has been used to measure the vapor pressure of thallium over pure thallium in the temperature range 931" to 996'k The resulting 100 cal per g-atom is in excellent agreement with previous values. Vapor pressures of T1 above seven Ag-Tl alloys ranging from 33 to 90 at. pct T1 were measured at 979K. Calculated silver activities show a positive deviation from Raoult's law, approaching ideality near the liquidus. Measured thallium activities scatter less than previous measurements using the electromotive force technique. Values for the silver component were calculated by Gibbs-Duhem integration. This paper reports the results of a study of the liquid Ag-T1 system by the torsion effusion method. The method has been discussed in detail previously1 and will be only briefly summarized here. The sample is contained in a cell which is suspended on a torsion wire. Vapors effusing from orifices on opposite sides of the cell exert a torque on the wire. The torque is related to the vapor pressure by the following relation: where D is the torsion constant of the wire, 4 the angle of torque, fl and f2 the correction factors determined by Freeman and seamy2 to account for orifice length, a1 and a2 the areas of the orifices, and ql and q2 the distances of the orifices from the axis of rotation. By using the same cell for pure thallium and the alloy, it follows that: so that most systematic errors are eliminated in determining the activities. EXPERIMENTAL 99.999+ pct T1 was obtained from the American Smelting and Refining Co. and 99.999 pct Ag was obtained from Cominco American, Inc. Seven Ag-T1 alloys, ranging in composition from x^\ = 0.33 to 0.90, were prepared by melting together weighed amounts of the pure metals in sealed, evacuated Vycor tubes and quenching the melts in water. The apparatus and graphite cells were the same as those used by Hawkins and Hultgren3 in their study of the Pb-Sn system. RESULTS Ten measurements were made on pure thallium in the temperature range 931" to 996K, and the results are presented in Table I. Values of were calculated using tabulated Gibbs (free) energy functions.4 No dependence of on temperature or orifice size was found, indicating that equilibrium was attained. Data for the Ag-T1 alloys are shown in Table 11. Values were smoothed with respect to composition by a plot of where . DISCUSSION The value = 43,520 * 100 cal per g-atom for pure thallium (95 pct uncertainty limit) is in excellent agreement with previous investigations.4 In the Ag-T1 system, this study shows positive deviations from Raoult's law at all compositions. Fig. l gives the phase diagram according to Hansen, and Fig. 2 presents the activity values measured in this study as well as those from electromotive force measurements at 950°K by Terpilowski, Kundys, and slaby.'

Jan 1, 1969

Aaby, Alton O , (S'47) Univ of Minnesota, Mimeapolis, Minn Aaby, Waldo S , (S?48) Univ of Minnesota, Minneapolis Minn Aalde, Kaare, (S'48) Univ of Nevada, Reno, Nev Aaring, Floyd D , (S'48) Univ of Oklahoma, Nor man, Oka Aaronson, Hubert I , (S'47) Carnegie Inst of Technology, Pittsburgh, Pa Abbott, Peyton Osborn, (S'46) 1502 Westover, Austin 21, Texas Abel, Malcolm D , (S'47) Univ of Texas, Austin, Texas Aberg, Richard S , (S'47) Univ of Minnesota, Minneipolis, Minn Abrahamson, Guy C , (S'43) 420 W Dennis St , Wilmington, Calif Abrahao, Benjamin, (S'46) Escola Politeenica da Unnersidade, de Sin Piulo, Braizil Achter, Meyer R , (S'46) Carnegie Inst of Tech , Pittsburgh, Pa

Jan 1, 1952

By Peter T. Luckie, Harold L. Lovell, E. R. Palowitch, A. W. Deurbrouck, James K. Kindig

PART 1: DENSE MEDIUM SEPARATION by E. R. PALOWITCH and A. W. DEURBROUK INTRODUCTION During 1965, 64.9 percent of the 512 million tons of bituminous coal and lignite produced was cleaned mechanically, of which 95 million tons was cleaned by dense medium processes.l The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes rose from 7.0 to 28.5 percent from 1938 to 1965. Dense medium separations include those coal preparation processes which clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes offer the following advantages over other coal cleaning processes : 1. Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of the feed in the range of e 0.1 specific gravity units. 2. Ability to maintain a separating gravity that can be controlled with ±0.005 specific gravity units. 3. Ability to handle a wide range of sizes (up to 14 inches). 4. Relatively low capital and operating costs when considered in terms of high capacity and small space requirements. 5. Ability to change specific gravity of separation to meet varying market requirements. 6. Ability to handle fluctuations in feed both in terms of quantity and quality. HISTORY Sir Henry Bessemer patented the first dense medium process in 1858. Solutions of the chlorides of iron, manganese, barium and calcium were proposed as separating liquids; the separation was made in a cone-shaped separator. One large-scale plant using calcium chloride was erected in Germany but soon was abandoned. The Chance process, using a mixture of sand and water, was first

Jan 1, 1968

America.-Foreman, J. T. Ashland.-Sturdevant, J. C. AItalIa. Henderson, R. M. Bessemer.-Ball, E. M. Maschmeyer, W. L. McKenzie, W. C., Jr. Birmingham.-Abbott, C. E. Aldrich, T. H. Aldrich, T. H., Jr Aufderhaar, H. C. Berg, H. A. Blair, C. S. Bush, M. W. Clark, G. H.

Jan 1, 1923

By R. M. Hudson

Equilibrium constants have been determined for the jeaction C (in steel) + H2O = CO + H2 as a function of carbon content (0.013 to 0.74 ujt pct) and temperature (1200° to 1800°F) by using a flow system in which the water-vapor content of various gas mixtures containing hydrogen, carbon monoxide, and nitrogen was systematically controlled. The equilibrium partial-pressure ratio K1 = PcoPH2/PH2O was obtained for two low-carbon steels and four Fe-C binaries from a series of runs made at each temperature. By comparison of Ki with the analogous ratio for the reaction C (graphite) + H2O = CO + H2, the activity of carbon in steel (ac) was comDuted for each temperature and carbon content studied. From these data values of the equilibrium constants for two other carburization-decarburiza-tion reactions of importance were estimated. The chemical compositions of the two steels and four Fe-C binaries used are given in Table I. Specimens of Steel E were cut from a 0.035-in.-thick commercially box-annealed and temper-rolled lot of a low-carbon low-metalloid steel. Steel F was a commercially hot-rolled rimmed steel that was cold-reduced at the Laboratory to a 0.059-in. thickness. Fe-C binaries A, B, C, and D were vacuum-melted and poured, hot-rolled, pickled, and cold-reduced at the Laboratory to furnish specimens 0.035 in. thick. Sheet specimens were cut from all lots to approximately 3/4 by 3 in. by gage and were vapor-degreased with trichlo-roethylene and weighed before heat treatment. Heat treatments were carried out in a hinged-top Hevi-Duty electric furnace with a Vycor-glass tube. When the furnace was at the desired

Jan 1, 1965

Jan 1, 1883

By Robert F. Mehl

THE solid solutions which aluminum forms with copper, and with magnesium and silicon, are not extensive, and accordingly could not be expected to form Widmanstätten figures profusely nor with great ease. A study of the Widmanstätten figures in these systems seemed desirable, however, because of the interest which these alloys bear towards age-hardening theories resulting from the necessary relationship between the age-hardening phenomena and the atomic processes leading to the formation of Widmanstätten figures.1 ALLOYS OF ALUMINUM WITH COPPER The most accurate determination f the solid solubility, of copper in aluminum seems to be that by Dix and Richardson,2 whose results are represented in Fig. 1. According to this work, aluminum dissolves 5.6 weight per cent of copper at 548°, and less than one per cent at room temperature. Judging from the constitutional diagram, this solid solution on cooling tends to precipitate the compound CuAl2, and this conclusion has been confirmed experimentally by Schmid and Wassermann .3

Jan 1, 1932

By Manuel Eissler

INTRODUCTION THE history of copper metallurgy in Japan goes back into remote ages, of this there is abundant proof, and that the working of this metal is closely connected with the artistic development of this nation is evidenced by some of the glorious monuments which have been produced by these ancient metal workers. The traveler sees to-clay in a perfect state of preservation bronze statues 150 ft. high, and over, 300 ft. in width, and 170 ft. in depth, delicately chased and beautifully marked, and when one reflects that some of them date back to the eighth century A. D., the question naturally suggests itself, how did these ancient metallurgists with their crude and primitive appliances accomplish this stupendous task? The bodies of these images are formed of bronze castings 10 to 12 in. thick, which were gradually built up and soldered together, but other pieces of magnitude, like the heads and other portions of the body are single castings. In many cases another method of construction must have been adopted. The walls of the molds were gradually built up and as the lower portion of the castings cooled, the walls were raised higher and higher and fresh metal must have been added, instead of constructing the whole mold first and then making the casting in one piece. There are still traces of substantial gilding visible on these statues, and how the pious Buddhist priests who were the constructors of them got the precious metal, is preserved in legendary tales.

Jan 11, 1914

E. D. WILLIAMSON,* Washington, D. C. (written discussion?).-The paper is interesting and suggestive and the work described should he carried to completion, as it presents points of interest quite apart from the immediate application in glass manufacture. It ought to help, for instance, in throwing light on the chemical nature of glasses and on all questions of viscous flow.

Jan 11, 1919

By Robert Keeney

THE electric smelting of manganese ore and the production of ferro- manganese did not exist as an industry, in the United States or elsewhere, previous to the outbreak of war in 1914. Ferromanganese had been produced, electrically, during times of high prices by two companies at Niagara Falls and by several European companies, but the production. was spasmodic, and none was electrically produced when ferromanganese sold at from $35 to $40 per ton. Thus the electric smelting of manganese ore must be considered as a development caused by the high prices prevailing during the years 1916, 1917 and 1918, and the necessity of smelting domestic ore in order to fill the ferromanganese requirements of the steel industry of the United States, which increased from 189,088 tons in 1914 to 356,356 tons in 1918. The electric furnace is well adapted to smelting domestic-ore because it can be located in small units near the source of ore supply. In 1918, the ferromanganese production of the United States was 333,027 tons, of which about 7 per cent., or 23,000 tons, was produced in the electric furnace. The electric furnace not only assisted materially in the development of a domestic-ore supply but made a considerable saving of coke, as it requires about 1,4 tons of bituminous or lignite coal per ton of ferromanganese compared with a blast-furnace consumption of 2.9 tons of coke per ton of ferromanganese. Some of the plants in the United States that smelted manganese ore in the electric furnace during the war and in 1920 are listed in Tabled. From early in 1919 to about February, 1920, little ferromanganese was produced in the electric furnace. During this period the price of ferro-manganese (78 to 82 per cent. manganese) was about $100 per ton. During the first half of 1920, several plants resumed operation when the, price of. ferromanganese (76 to 80 per cent. grade) gradually increased to $200 per ton, delivered.

Jan 2, 1921

By R. P. Ehrlich, D. A. Dahlstrom

In the hydrometallurgical circuit, many phase separation steps are usually necessary. Typical steps are pregnant liquor - leach residue separation by counter- current decantation or continuous vacuum filtration, clarification of liquids prior to precipitation, ion exchange or solvent extraction, dewatering of final product, etc. The paper discusses the more recent advances in these areas and considers general operating parameters and cost factors. In addition, emphasis is placed on future needs because of the growing importance and necessity of hydrometallurgical processing of minerals.

Jan 1, 1973

By Theo B. Comstock

Since 1892 the writer has published several articles in the Engineering and Mining Journal concerning the relations of the

Jan 1, 1901

By H. J. Mutz

THE International Nickel Co. of Canada Ltd. operates five underground mines and an open pit. Four of the mines, the Frood-Stobie, Creighton, Murray, and Garson, are on the south range of the Sudbury Basin, map above, within a radius of 10 miles of the city of Sudbury, Ontario. The fifth mine, the Levack, is on the north range of the Sudbury Basin, 30 miles to the northwest of the city. The open pit is operating on surface ores of the Frood-Stobie orebody.

Jan 1, 1953

By J. O. Brittain, E. P. Lautenschlager, D. A. Kiewit

Compression tests were run in the temperature range of 700° to 900°C ox 0' phase NiAl intermetal-lic alloys of several grain sizes. At these temperatures the minimum strengths were observed at the stoichiometric composition. While significant increases in strength occurved in both the low-nickel (vacancy) and high-nickel (substitutional) regions, the highest strengths were found in the high-nickel region. During deformation serrated flow was sometimes observed in the low-nickel alloys. After deformation transgranular cvacking and deformation striations were observed in all compositions tested. AS part of a general investigation of the properties of NiAl inter metallic compounds, a preliminary study of the role of point defects upon plasticity was made by high-temperature compression tests on ß' NiAl specimens of several grain sizes and compositions. ß' NiAl is an intermetallic compound having a CsCl structure and a rather wide range of composition from A1-45 at. pct to 60 at. pct Ni.1 According to Bradley and Taylor2 and to cooper,' it possesses a defect lattice in which departures from stoichiometry in the direction of decreased nickel content lead to the presence of vacant nickel sites (although Cooper's work indicates that a small amount of substitution also occurs) whereas departures on the high-nickel side lead to substitution of nickel on aluminum sites. NiAl forms congru-ently from the melt at approximately 1650°C,1 and thus has a higher melting point than either of its component elements. Up to this time, although this and other high-melting intermetallic compounds have been suggested for elevated-temperature usage,4 only the hardness4 and a few tensile-strength measurements5 have been reported for NiAl at high temperatures. In the present investigation the effects of composition upon the compressive-strength properties in a range of 700° to 900°C have been measured for NiAl of several grain sizes. EXPERIMENTAL PROCEDURES The alloys were made as described elsewhere6 from an A1-46.8 at. pct Ni master alloy furnished by the International Nickel Co. with additions of high-purity nickel and aluminum. The charges were vacuum-induction-melted in A12O3 crucibles with small amounts of helium added to the atmosphere to suppress vaporization. They were cooled slowly from the melting temperature to achieve uniform grain size. In order to refine the as-grown grain size a special rolling technique was developed. Alloys were packed into 0.10-in. wall-type 302 stainless-steel tubes which were partially filled with magnesium oxide to prevent bonding between the alloy and the steel jacket. The ends of the tubes were closed by hot forging, and the packets were then hot-rolled. The alloys with greater than 50 at. pct Ni were rolled at 1100°C, but it was found necessary to increase the temperature to 1350° C before alloys with less than 50 at. pct Ni would roll without cracking. With these temperatures, reductions as high as 48 pct were achieved in a single pass. The rolled alloys will hereafter be referred to as "fine grained" whereas the as-grown material will be designated "coarse-grained''. The compression specimens were made by cutting square cross-sectional pieces, approximately 3/16 by 3/16 by 1/2 in., with a water-cooled diamond cut-off wheel from the as-grown or the rolled alloys. Specimens were ground to their final dimensions by polishing through 3/0 grit silicon carbide papers. The final shape was a rectangular parallelepiped of square cross section having a height-to-width ratio of 3:1. Compression testing was carried out in a compression rig of our own design mounted on an In-stron Floor Model. The specimen chamber could be heated to 1000°C and was controlled within ±2°C. The compression rig was enclosed within a bell jar and was maintained at a 50 µ of mercury vacuum throughout the duration of the test. The test cham -ber was heated from room to test temperature within 15 min. Specimens were then held at the test temperature 30 min prior to testing. Previous experiments indicated that no grain growth would occur within this time. An Instron Variable Crosshead speed unit was used to adjust for small variations in specimen lengths in order to have a constant initial strain rate, €, for all specimens of a group. For the fine-grained specimens the strain rate was changed rapidly at constant temperature by a factor of 10 with the speed lever on the Instron. For a given € the compression data was analyzed in terms of true plastic strain (E) and true compressive stress (0).

Jan 1, 1965

By T. G. Fulmor, William Wraith

What impelled The Anaconda Company to dismantle and move a concentrator 25 miles that was already operating at a rate of 35,000 ton per day? The answer to that question takes in almost exactly 49 years and perhaps 10 complete cycles of the metallurgical wheel in the Anaconda, Mont., mill. One could say with truth that the move is a logical next-step in the development of metallurgy in The Anaconda Co. In the old concentrator at Anaconda, the background story is unfolded: - Gravity separation by jigs, later supplemented with gravity tables, 1905. - Separate sand and slime froth flotation, 1915. - Acid bulk froth flotation, 1917. - Bulk alkaline flotation, 1926. - Alkaline flotation of total ore without sand- slime separation due to change in ore type. 1939.

Jan 5, 1964