Search Documents

By Julian Szekely

Through the simultaneous statement of Maxwell's equations. the turbulent Navier-Stokes equations and the differential thermal energy balance equation, a mathematical representation has been developed for heat transfer and fluid flow in electric arc furnaces. In broad outline the theoretical predictions appear to be consistent with experimental measurements. A discussion is presented of the general arc furnace control and optimization problem, together with the potential for the incorporation of the mathematical model given in the paper, into future control and optimization schemes. ELECTRIC ARC FURNACE STEELMAKING accounts for about 24% of the total steel produced in the U.S., consuming about 550kw-hr/ton of steel which amounts to about 1.4x1010 kw-hr annually. The percentage of steel produced by the electric arc furnace route has doubled since 1960 and is expected to increase further in the foreseeable future, particularly with the more extensive use of direct reduction technology. Table I shows, in terms of percentages, the principal items that contribute to the cost of running an electric arc furnace. It is seen that in addition to the fixed costs (labor, depreciation, taxes etc.) electrode costs and power consumption are the dominant inputs, and it follows that process changes that would ultimately reduce any of these cost components would have a significant impact on the efficiency of the operation. There are three main areas where progress in arc furnace design and operation must be directed in the next decade (Committee on Technology, 1981). 1. Increased furnace productivity 2. Reduction in processing cost 3. Improvement in the thermal efficiency of the furnace An estimate of the current operating efficiency of the electric arc furnaces may be obtained by comparing the theoretical minimum energy consumption per ton of steel with those achieved in operational practice. Theoretically 330-360 kw-hrs of electricity are required to melt one ton of cold scrap. For superheating, 8-12 kWh per 100°F are required. The actual energy requirements are given in Table II. It is seen that furnaces currently operate at 70-80% efficiency, with the major heat loss from the furnace resulting from the waste gases (Committee on Technology, 1981). While it is apparent that operational experience has produced a technology that is reasonably energy efficient this has been achieved in the almost complete absence of any detailed knowledge concerning the fundamental heat transfer mechanisms occuring in the furnace. The purpose of the present paper is to present a case for the usefulness of mathematical models in increasing the thermal efficiency of furnaces by investigating these heat transfer mechanisms and then combining this knowledge with existing electrode regulator mechanisms to produce truly efficient power cycles for melting and refining. In particular, existing mathematical models describing convection, radiation, and electro-magnetism in the furnace should be employed, and the development of optimization models which balance the cost of electrodes and energy against the thermal efficience of the furnace should be undertaken. Recent work in this laboratory (Szekely, McKelliget, 1981, 1982, 1983; Szekely, McKelliget, Choudhary, 1983) has made a useful start towards solving the problem of heat transfer within the electric arc furnace but the work still needs to be directly related to existing furnace power cycles and tested against plant scale measurements.

Jan 1, 1984

By C. C. Wright, T. S. Spicer

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By T. S. Spicer, C. C. Wright

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By Claudio Guarnaschelli

Alteration of the electronic distribution of mineral surfaces by light irradiation has been used to modify the adsorption characteristics of flotation reagents. Energy of a few electron volts is suficient to cause the necessary transitions that either enhance or retard the adsorption phenomenon. The adsorption characteristics of potassium ethyl xanthate on galena and marmatite are presented as functions of the energy of illumination, type of semiconductor, and surface oxidation. In dilute solutions, the adsorption differences are readily detected by controlled kinetic measurements. The correlation between the electronic distribution and the adsorption and desorption phenomena at the solid surface is gaining more attention and acceptance. These interrelations have found a practical application in mineral processing since all of the sulfide minerals display semiconducting properties. By varying the ratio of free electron to electron vacancies, the separation of ilmenite from rutilel and zircon from pyrochlore" has been executed successfully. Plaksin et al.' indicate three possible ways of utilizing the semiconductor properties of a mineral. The first one involves the control of the oxidation-reduction potential of the liquid phase, the second one consists of allowing selected additives to diffuse through the mineral surface, while the third one entails a change in the adsorption and chemical activity of minerals by irradiating their surface. The aim of the present work is to consider the effect of irradiation on the adsorption-desorption characteristics of natural minerals. Since the effect of irradiation is to change the electronic distribution at the surface:

Jan 1, 1971

By A. H. Daane, J. F. Haefling

The limits of miscibility in some of the uranium rare-earth alloy systems have been determined in the temperature range 1000°to 1250°C. The solubilities of lanthanum and cerium in uranium are greater than those of the remaining rare earths by a factor of more than two. The solubility of uranium is greater in cerium, braseodymium, and neodymium than in the other rare-earth metals studied. The values found in this study are in qualitative agreement with those which might be expected if the solubility rules of Hildebrand and Scott are applicable. AS interest in nuclear reactors intensifies, many new types of fuels are being suggested in attempts to improve the economics of some of the proposed reactor schemes. To remove some of the difficulties inherent in the use of solid-fuel elements and their reprocessing, many types of liquid-metal reactors have been suggested. One of the more attractive features of several of these reactor concepts is that they include a continuous or semicontinuous process for the extraction of fission products and "bred" fissionable materials from the fuel, utilizing immiscible metal extractants. This would enable a much higher burn-up of fissionable material to be achieved and would present a very attractive economic picture. Several studies have been reported on equilibrium systems in which there exists a high degree of immiscibility between uranium and another metal that might be used as an extractant in such a processing scheme.' Two of these systems in which a high degree of immiscibility exists are those of uranium with the two rare-earth metals, lanthanum, and cerium. Since the rare earths constitute a significant fraction of the fission products, their removal is of prime importance. It is reasonable to believe that this might be accomplished by equilibrating a rare-earth phase with the contaminated uranium fuel in the liquid state. In order to make a more complete study of those systems which would be of interest either as extractants in a liquid-liquid extraction process, or as fission products formed in the fuel, the alloy systems of uranium with lanthanum, cerium, praseodymium, neodymium, and samarium were studied in some detail in the temperature range 1000" to 1250°C; less detailed studies were made with the other rare earths. In addition to being of value to the reactor program, the data obtained in this study should be of help in making a study of the role played by the electronic structures of metals in determining the nature of metallic solutions. The unique electronic structures of the rare-earth elements make them particularly interesting in this respect. EXPERIMENTAL The usual procedure for a solubility determination was to seal equal volumes of uranium and the particular rare earth in a tantalum crucible under an atmosphere of helium; this crucible was then sealed in a stainless steel jacket in an atmosphere of helium. These samples were equilibrated by repeated inverting of the crucibles in a furnace for 15 min at the desired temperature, left in an upright position for 15 min to permit separation of the two phases, and then quenched under a stream of water. In some runs the temperature of the furnace was held 50' to 100°C above the desired quenching temperature while inverting in order to insure good mixing. However, it was found that above 1200°C the crucibles were subject to failure and for these runs the furnace temperature was not raised above the desired quenching temperature. A small amount of tantalum was dissolved in the uranium and the rare earths in these runs, a maximum of 3 wt pct in the uranium phase at 1250°C and up to 1 wt pct in the rare-earth phase at this temperature. On cooling, the major portion of this tantalum precipitated as primary tantalum crystals. Any residual tantalum would probably have a negligible effect on the mutual solubility of uranium and the rare earths in each other. Samples for analysis were cut from each phase with an abrasive cutting wheel; the region near the interface between the two metals was carefully avoided. In the case of the rare earths with melting points above 1250°C no solubility data were taken on the rare-earth phase since this phase could not have achieved equilibrium in a reasonable length of time. (For the same reason no data were taken on the uranium phase below its melting point of 1132°C.) Equilibrium appeared to have been reached in the uranium phase in these cases although the rare-earth phase had not melted. To verify this, samples were melted together in an arc furnace similar to that described by Kroll.2 These samples were sub-

Jan 1, 1960

By T. A. Klinefelter, O&apos, R. G. Meara, Glenn C. Truesdell, Richard W. Smith

The investigation of domestic talcs was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. 1, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for' aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." History The use of steatite and talc in ceramic bodies goes back a great many years. If pure, talcs shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a. large business was carried on in the manufacture of tips for gas burners.' With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Man-churian talcs. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1948

By T. A. Klinefelter, Glenn C. Truesdell, Richard W. Smith, R. G. Meara, O&apos

The investigation of domestic talcs was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. 1, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for' aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." History The use of steatite and talc in ceramic bodies goes back a great many years. If pure, talcs shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a. large business was carried on in the manufacture of tips for gas burners.' With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Man-churian talcs. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1948

By AIME AIME

AMONG the members of the Institute there are thirty-three who have been members for a half- century or-more Some time ago a professor of psychology made a careful study of a group of unusually brilliant children to determine whether there was any truth in the general belief that a brilliant mind is usually to be found in a physically sub-normal body. He definitely proved the exact opposite and it is now known that children who are above the average in mental capacity are also above the average in physical health and strength.

Jan 1, 1929

By T. S. Spicer, C. C. Wright

A CHARACTERISTIC property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent, but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire The plastic mass prevents uniform distribution of air through the fuel bed and, With strongly coking coals, large dense pieces of coke are produced which have much less reacting surface thin was possessed by the original coal In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued) automatic service In order to burn strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation continuous, intermittent and hold-fire, frequent attention is necessary Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb of coal or less per hour With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel-bed Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals The work of Bituminous Coal Research Inc at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker Typical coke formations in a clinkering type of underfeed domestic stoker are illustrated in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal, (B) the type of fuel bed formed -with, a coal that produces a weal coke, and (C) the type of fuel bed obtained with a strongly coking coal C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is ,burned in an underfeed stoker of conventional type It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals

Jan 1, 1942

By Nelson Severinghaus

Crushed stone leads all industrial mineral, except cement in annual value of production in the United States. It is also interesting to note that crushed stone value is exceeded only by that of fuels, cement, and iron ore among all mineral products of this country. An industry which started with hand-sledging to produce smaller sizes of broken stone for hard surfaced improvement of roadways as designed by McAdam in England about 1815 has grown into a complex industrial giant. Most of this growth started with the invention of a mechanical rock crusher just under one hundred years age (1858) by Eli Whitney Blake. This invention made possible the production of greater tonnages of smaller sizes of broken stone and greatly accelerated its use for Macadam road pavements and for railroad ballast. Stones Used for Crushing All three of the major geologic classifications of stone, sedimentary, igneous, and metamorphic, are widely used in the production of crushed stone. Satisfactory physical and chemical properties can be found in each type so that economic availability becomes the prime determinant for development. Table 1 lists more common rocks of the three main groups with average values of specific gravity and toughness as measured by Deval test. This widely used classification was suggested by C. E. Lord, of U. S. Bureau of Public Roads. The physical properties were compiled by D. O. Woolf in "The Results of Physical Tests of Road Building Rock," U. S. Department of Agriculture, Bulletin 76. It should be noted that the figures given in Table 1 are averages. Very substantial variations in the physical properties of rocks within any one classification will occur. The solid surface of the earth was first made up of igneous rocks resulting from the solidification or crystallization of molten material upon cooling. These igneous rocks were disintegrated into sand, clay, and gravel by the weathering action of wind, water, chemicals, [ ] and temperature changes. The products of weathering were transported by wind and streams until they reached less turbulent areas such as oceans or lakes and were deposited. Chemical deposition between grains of sand or clay or the physical action of pressure and heat then solidified them into sedimentary rocks

Jan 1, 1960

EDWARD W. PARKER,* Philadelphia, Pa. (written discussion ?).-The two papers on coal-mine costs and pride fixing that Mr. Norris has contributed to the Transactions possess as much general interest and are of as much value to the coal-mining industry as any papers that have been presented in recent years. Until recently one of the troubles with the coal business, and especially the bituminous branch of it, has been that because of the lack of a uniform system of cost accounting (many operators, I regret to say, not having had any system at all), the industry as a whole may be said not to have known where it was at. The system adopted by the Federal Trade Commission may not be absolutely perfect but it has accomplished something in that it has compelled a uniform method of reporting and tabulating costs giving results of these compilations which are comparable. The Institute and the coal-mining industry owe a vote of thanks to, and of confidence in, Mr. Norris and his two associates on the Engineers Committee of the Fuel Administration, Messrs. Garnsey and Allport, for the great work they have done in interpreting the results compiled by the Federal Trade Commission, not to speak of the personal sacrifices made by them in giving their services to the government. Those who have read Mr. Norris' paper will probably join me in wishing he had brought out a little more fully the real meaning of the charts so far as they indicate the difference between the cost of producing a ton of anthracite and the price the operators receive for their product. Mr. Norris could have done this more satisfactorily than anyone else. It seems to me that particular attention should be drawn to the fact that, according to these charts, and the tables accompanying them, not less than 25 per cent. of the total output of anthracite, whether "company" or "individual," during the period covered by Mr. Norris' paper,

Jan 4, 1919

By Shiou-Chuan Sun

SHIOU-CHUAN SUN (author's reply).-Thanks are extended to Professor Hassialis for his recognition of the usefulness of a new tool, the cataphoretic cell, as an adjunct to the bubble machine and the abstraction test. His questions concerning adsorption, dielectric constant, floatability, activation, and depression are interesting and worthy of discussion. I According to Mueller,28 it is questionable that any of the present formulas gives absolute values of zeta potentials which are completely accurate. The problem is further complicated by the question" of whether the "dielectric constant" has any meaning at all for such a microscopically thin layer. With these in mind, the results in this paper should be considered in the relative sense as a first approximation and not as absolute quantities. Adsorption Referring to item a of Fig. 8, the dielectric constant and the viscosity of the xanthate solutions are the same for galena, sphalerite and quartz. If dielectric constant and viscosity (but not the adsorption) were the first-order variable of the cataphoretic system, as claimed by Professor Hassialis, then the magnitudes of zeta coefficient of galena, spha)erite and quartz would have been similar to each other. These are not. The big difference of zeta coefficient of these three minerals in the same xanthate solutions is not altogether unjustified to be attributed to their difference in adsorption of xanthate ions. This is supported by the results of chemical abstraction tests reported by Ince.14 Again, the big difference of zeta coefficient between wollastonite, calcite, and fluorite in the same laurylamine hydrochloride solutions (p. 118, Figs. 58, 59, and 60 of ref. r5) also indicates that the cataphoretic system is not governed chiefly by the dielectric constant. Beside the data shown in Fig. 8, other experimental evidences15 which support the idea of correlation between adsorption and zeta coefficient are: (I) there is a qualitative parallelism between the zeta coefficient curve and the chemical abstraction curve of sphalerite in solutions of various concentrations of sodium cyanide, (2) there is a qualitative parallelism between the zeta coefficient curve and the chemical abstraction curve of sphalerite in solutions of constant concentration of copper sulphate at different pH values, and (3) there is a qualitative parallelism between zeta coefficient curve and chemical abstraction curve of quartz in solutions with constant concentration of barium chloride at different pH values. The above mentioned experimental results are generally in agreement with Gouy's double layer theory,1-5 and support this idea that the concentration and the kind of ions adsorbed at the mineral surface and in the adjacent surrounding liquid chiefly govern the electrokinetic phenomena. Dielectric constant and viscosity of the liquid medium may be of somewhat lesser importance. It follows that the correlation between the coefficient and adsorption as claimed in this paper is justified. Dielectric Constant The term "dielectric constant " was first introduced into the electrokinetic equations by Perrin.30 In a footnote of his publication he states that Holmheltz has forgotten to include the dielectric constant. The conversion of the moment29 to the zeta potential involves an additional difficulty and confusion not involved for the moment, namely, assigning a value to the dielectric coefficient. This is conventionally assumed to be constant and equal to the dielectric constant of the bulk liquid. 21 The published literature 10, 12 indicates that the values of dielectric constant for dilute chemical solutions have been assumed as those of pure water.

Jan 1, 1947

By B. Ramaswami, Y. Nakada, R. Schaefer

EARLY investigations1 of the tensile properties of fcc single crystals did not reveal the easy glide region of crystals with axial orientations inside the standard stereographic triangle. With the production of high-purity metal, a region of easy glide became known1 Consequently, modern work of fcc single crystals ordinarily uses high-purity metal. In order to determine whether further purification of aluminum beyond 99.992 pct purity would result in significant alteration of the tensile properties of single-crystal specimens, metal was zone-refined and crystals grown from the purified material were compared to crystals grown from the original material. Some similar studies were made of gold and silver crystals. Aluminum. The material to be zone-refined was cast into bars 1/4 by 1/2 by 8 in. A zone, approximately 1-1/2 in. in length, was passed over each bar eighteen times at a rate of 6 in. per hr. Melting and stirring were carried out by an induction heater under a vacuum of approximately 10"5 mm Hg, the metal being held in a graphite container. he last 3 in. of each processed bar were then cut off and discarded. No quantitative determination of purity was made, but the effectiveness of the zone refining was tested by a method first suggested by Walton, Tiller, Rutter, and winegard3 depending on the relation between cell structure and impurity content. Rutter and Chalmers4 have shown that a cellular substructure is associated with the presence of impurities during solidificatibn, and have shown how solute rejection at the freezing interface can lead to such an association. Thus the observation of cells gives evidence of impurities being present. To look for cells, the last quarter of a zone-refined bar was cut off, remelted, and grown rapidly into a single crystal. It was then heavily electropolished and thermally etched.~ Cells were revealed by the presence of many parallel rows of etch pits. The same process was carried out with material from the first half of the bar, but no cells were detected. These observations give evidence that a significant amount of impurity material was moved to the "dirty" end of the zone-refined bars. Further indication of purification was obtained from recrystallization experiments. It was found that, after cold rolling to a 97 pct reduction in thickness, the material from the pure end of the bar re-crystallized at room temperature, but the material from the "dirty" end did not. Other investigators6 have previously reported that zone-refined aluminum recrystallized at room temperature. The purified material was cast into 1/4 by 1/4 in. bars, and seeded crystals were grown in a (100) orientation and in a single slip orientation where the Schmid factor is m =2. The crystals were then cut to the desired length, annealed for 24 hr at 610°C, furnace-cooled, and etched in Tucker's etch. The crystals were tested in a floor-model Instron machine, using a gage length of 4 in. and a strain rate of 1/2 pct per min. The resulting curves are shown in Fig. 1. It is seen that the differences between the curves for zone-refined and original-purity materials are small. These differences are within the scatter observed for crystals of the original purity. In particular, the zone refining does not significantly affect the onset of the different "stages" of the curves.

Jan 1, 1964

By J. H. Frye, C. P. Sun

A PRIMARY substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver aneys.1-5 It has been shown that at least, four factors are involved: (I) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2.4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. CALCULATION OF RATES OF WORK- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By J. C. McDonald

A DDITIONAL experimental data are presented in this note on a phenomenon which has been touched on but lightly in the literature. The common magnesium base rolling alloy (AZ31B) contains about 3 pet A1 and 1 pet Zn. When cold rolled, it hardens until it starts to break up in the rolls at 30 to 50 pet reduction. When it is heated after rolling to full hardness, it softens. However, other magnesium alloys have shown themselves capable of being cold rolled indefinitely, provided the ratio of roll diameter to starting gage is sufficiently high. As measured by the tensile test, these alloys actually soften when the reduction becomes large (60 to 90 pct). A subsequent heating at 300' to 500°F can produce hardening of this metal. Heating at higher temperatures (600' to 800°F) causes recrystalliza-tion and softening. Menzen' has shown that a magnesium base alloy can be cold rolled without intermediate anneals as much as 90 pet. The alloy studied, Mg-1.5 pet Mn, softened considerably between 20 and 90 pet reduction, as measured by tensile properties; a decrease in yield strength of 30 pet, and an increase in elongation from 3.2 to 16.7 pet (longitudinal direction of the sheet). However, Menzen gives no data on the reaction of this metal. to heating. Ansel and Betterton2 and Hurst and Hatch3 report a similar effect in Mg-1.5 pet Mn-0.1 pet Ca. Their data show an initial hardening, followed by softening. The former authors also show that the alloy softened by cold rolling will harden when heated at low temperatures, and that these effects are absent in Mg-3 pet Al-1 pet Zn. In the course of work4, 5 some years ago, the author observed similar effects with alloys containing cerium, thorium, or zirconium; but not with elements like aluminum, silver, or zinc. Table IA contains the results of an experiment which shows these effects rather well. A binary alloy with 0.3 pet total rare earths (Mischmetal* added) was rolled hot to 1/16 in. and then annealed to full softness by heating 30 min at 800°F. Rolling was continued at 1.5 pet per pass to 80 pet total reduction on 8 in. diam rolls. The metal was harder after 20 pet work than initially but, at 80 pet reduction, properties were back to their original values. Heating for 1 hr at 450°F produced about the same hardness whether the reduction was 20 or 80 pet. At intermediate reductions, the metal hardened, but not to as high values. Extensive cold rolling may also be carried out on metal hot rolled at temperatures sufficiently low to produce a semihard temper. Mg-0.6 pet Zr was rolled to 0.1 in. at 700° to 800°F, 30 pet per pass. As shown in Table IB, a further cold reduction of 85 pet, at 1.5 pet per pass, definitely softened the metal.

Jan 1, 1959

By Philip B. Dettmer

Up to now we have spoken optimistically of the many potential savings in capital and operating costs to be obtained from the selection of larger diameter and horsepower grinding mills. Such mills may well be the correct choice for one grinding plant but could be absolutely wrong for another plant. It is emphasized here that many significant factors other than the capital cost, labor, grinding media and power savings are involved in the sizing and selection of the optimum grinding circuit. The following discussion covers some of these factors and their relationship to larger mill design. The first consideration is: What is the grinding circuit supposed to do? In most instances it is one or both of the following: 1. Grind the feed material fine enough to liberate the desired minerals but with a minimum of over- grinding. Examples are preparation of ore for flotation, gravity separation, etc. 2. Grind to some pre-specified particle size or particle surface area. Examples of this are cement manufacture or the preparation of feed material for pelletizing; other examples are preparation for chemical reactions or ceramic manufacture.

Jan 5, 1965

record with the Royal Flying Corps was considered a remarkable one, for he was at the front within two months of the date on which he was granted a commission, during which interval he took the prescribed technical course at Oxford, and aviation training at Netheravon and Bristol. On Sept. 14, 1916, he took his first flight over the German lines, when his engine stalled and he had to volplane down, fortunately landing on the French side of the lines. On Sept. 16, he went over the lines with six others, and not returning immediately with the others, was lost. He tried to make for the sea and come back following the course of a river, but when he did descend he found that he was 60 miles west of Paris and 100 miles south of his lines. He flew over to Paris and stayed there for the night, going back to his squadron the next morning. Then on Oct. 4, he was sent up at night for the first time, and in making a landing he passed the flares just as he struck the ground, which put him in total darkness. He struck something and his machine turned a complete somersault, which accident put him in the hospital for ten days. In December, 1916, he left the 21st Squadron and was transferred to the 24th, as the 21st was made an Artillery Squadron and he preferred to remain a fighting scout. In the same month, he was made Acting Flight Commander for about 6 weeks, and about April 3, 1917, his rank of Flight Commander was confirmed. The beginning of May he started to introduce a number of new machines for his squadron, these being of an entirely new type. On May 19, he was up with one of the machines in the evening, practising sharp turns and dives, when the wings suddenly crumpled up and he fell 700 ft., being killed instantly. He was buried in a French Cemetry at Monchy Lagache about 8 miles southeast of Perronne, and about 25 miles east of Amiens. Sergeant Herbert Moore Harbach Herbert Moore Harbach was born in Lebanon, Pa., Apr. 4, 1891, graduated from the Lebanon High School in 1911, and entered State College from which he received his degree of Bachelor of Science in Metallurgical Engineering in 1915. He was employed by the Lackawanna Iron Co., at Buffalo, W. Y., and was later transferred to their Lebanon plant to start up the newly erected benzol plant. He was later made foreman of the coke ovens, which position he held after it was bought by the Bethlehem Steel Co., and until he enlisted in the service of his country in September, 1917. He was stationed at Camp Meade, Md., until the spring of 1918, when he was transferred to the C. W.

Jan 1, 1920

By A. Kaufman

More than 3 trillion gal of water are used annually by the mineral industry. Of this, approximately 21/2 trillion gal are recirculated, the rest constituting intake water. The major users are natural gas processing plants and phosphate rock, sand and gravel, and iron ore producers. Water was used by the mineral industry for mining (6%), processing (64%), cooling and condensing (27%), and miscellaneous uses such as boiler feed and sanitary purposes (3%). Whereas total water use is dependent on the quantity of material processed and on the particular process requirements of an industry, recirculation is dependent on processing, as well as cooling and condensing requirements, quality of new water intake, and the necessity for treating new and discharged water. Consumed water, on the other hand, is dependent on the quantity of water recirculated, and temperature and humidity in the area. Based on this analysis, an increase in water use by the mineral industry of 21/2 times by 1985 is forecast. Wster intake, however, will only rise 62%, because of a substantial increase in recirculation. In one report of a special series concerning the water resources of the United States, the Senate Select Committee on National Water Resources, 87th Congress, estimated that water demand would double by 1980 and triple by 2000.' In view of the possible water deficiencies that might result from such expanded usage and the need for research guidance, the Bureau of Mines organized and carried out a statistical canvass of water use in the mineral industry for calendar year 1962. The data used in this paper, unless otherwise noted, are derived from that canvass.' The efforts in this paper are devoted toward summarization of the canvass and analysis of the data. SOME DEFINITIONS Intake: Water introduced from an external source for the first time into a given mine or plant regardless of quality. Intake water is also called new water, water withdrawn, or makeup water. Fresh Water: Water suitable for cooking and drinking. Saline Water: Water containing more than 1000 parts per million of dissolved solids. Contaminated Water: Water not suitable for domestic use, but excluding saline water. Recirculated Water: Water reused to conserve intake water. Solutions that are recycled primarily because of fixed metallurgical practices, such as copper leaching solutions containing sulfuric acid, are excluded. Gross Water Used: Recirculated water plus intake water. Also called total water used. Consumed Water: Water that is lost by evaporation, as well as water lost in product. Seepage and transferred water are not considered consumed. The use of either intake or recirculated water may result in consumption. However, because of difficulties in measuring consulmption, consumed water is defined as the residual between intake and water discharged from the mine or plant. Mineral Industry: For the purposes of this paper, mineral industry includes all metal and nonmetal surface and underground mines and their associated processing plants, as well as custom mills, coal washing plants and associated mines, petroleum and natural gas well drillers, natural gas processing plants, and secondary recovery operations. WATER USE IN THE MINERAL INDUSTRY Water used by the mineral industry constitutes a relatively minor fraction of the water withdrawn by all users. Data compiled by the U.S. Geological Survey in 1960 indicate that water withdrawals, exclusive of that used to generate hydropower, approximate 99 trillion gal annually.3 Our data indicate that water withdrawals by the mineral industry comprise only 1% of this total, or 2% of the water withdrawn by industrial users. Use by Industry: Water used by various mineral industries is shown in Table I. The table indicates that close to one-half of the gross water used by the mineral industry in 1962 was used by natural gas processing plants, followed by sand and gravel, phosphate rock, and iron ore producers. The largest aggregate users of water are also the largest users per dollar of product. For example, Fig. 1 shows that the natural gas processing and phosphate rock industries are very large users of water per dollar of product. Their recirculation per

Jan 1, 1968

By William Braden

IT is obvious that the choice of the method to be employed in the handling of blast-furnace slags and mattes depends upon local facilities and conditions which may indicate as advisable some particular plan. As a result of the variety of such conditions hardly any two smelters use identically the same method, though they be located only a few hundred feet apart. For instance, of the several plants in Leadville, Colorado, each has a more or less distinctive system. The same is true of Salt Lake City and vicinity. In view of this it is evident that the existing diversity of practice cannot be accepted, prima facia, as evidence

Jan 1, 1897

By G. M. Swinkels, A. Vizsolyi, E. Peters

A process is described utilizing ferric chloride leaching followed by reduction of the cupric content to cuprous by cement copper, with CuCl obtained thereafter by crystallization. The residual liquor is cemented with sponge iron to produce cement copper and a copper free ferrous chloride solution. The latter is oxidized in an autoclave with oxygen to regenerate ferric chloride and to precipitate excess iron as a granular, filterable hematite. Cuprous chloride crystals are reduced to high purity metal with hydrogen, while sulphur reports almost quantitatively in residues in the elemental form. Pyrite and molybdenite are not leached. This paper describes the important variables in the process, as well as the deportment of minor elements as silver, gold, selenium, tellurium, bismuth, nickel, lead, zinc, magnesium, etc. An elegant method of isolating silver from CuCl crystals is described, as well as recovery of gold from residues by a chloride reagent The process is described as non-polluting and capable of producing refined copper, ore grade iron oxide, elemental sulphur, and yields of minor metals as good or better than obtainable by conventional smelting, without the use of solvent extraction or electrochemistry.

Jan 1, 1981