Search Documents

By George B. Langford

The McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dies of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compres-sive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed—an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magrna that supplied the albitite dikes. Introduction The McIntyre mine, in the Porcupine gold area of northern Ontario, has passed its twenty-sixth birthday and has been producing gold since early in 1912. During this time approximately ten million tons of ore has been mined and over three and a half million ounces of gold recovered. This amount of ore would be sufficient to fill 2300 standard railway freight trains, each of 100 cars, and the gold produced, although only equivalent to a cube 51/2 ft. to the side, would weigh approximately 100 tons, a load for three freight cars. Silver has been produced in the ratio of 1 oz. of silver to every 4.4 oz. of gold, so that the total silver recovery is in the neighborhood of 700,000 ounces. The early history of the mine, like that of many others, shows that for several years it fought an uphill struggle for existence. One of the important features in winning this fight was the early recognition of some of the geological conditions responsible for the ore deposits, and the application of this knowledge in the search for ore and in the acquiring of adjoining properties. As early as 1913—only two years after the mine was opened—a geological department was organiaed. It has functioned almost continuously since that date and has demonstrated the importance

Jan 1, 1941

The Institute is custodian of funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given be- low. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers. The Institute is represented with these four societies on the committee in charge of the Alfred Noble Prize.

Jan 1, 1932

By T. F. Bower, M. C. Flemings

The classical explanation for formation of the fine equiaxed "chill zone " in ingot solidification is that local supercooling near the chill wall causes copious nucleation in this region. This work indicates, however, that convection is an essential element in formation of the chill zone. In the absence of convection, no chill zone forms even though rate of. heat extraction is extremely vapid. Alloy studied was Al-l.5 pct Cu alloy solidified against a copper chill wall. When solidification was initiated at the chill wall in absence of. cor-vection, surface grain size was large (>I cm diam). When it was initiated in the presence of convection, it was fine (<0.05 cm diam). It is concluded that some form of "crystal multiplication" plays an important role in formation of the chill zone. INGOT macrostructures are generally classed as containing one or more of the three zones: "chill zone", "columnar zone", and central "equiaxed zone". These three zones are sketched in Fig. 1; their origin has been discussed in some detail.&apos;-&apos; The classical explanation for formation of the chill zone is that supercooling occurs in the region of liquid metal adjacent the mold wall, and copious nu-cleation then takes place in this region forming numerous small crystals. The columnar region then results by growth of favorably oriented grains (den-drites) which crowd out their less favorably oriented neighbors."5 The mechanism of the columnar-equiaxed transition has been the subject of considerable interest. The generally accepted mechanism, until recently, was that constitutional supercooling developed in front of the growing columnar grains with eventual nucleation of new, equiaxed, grains ahead of the growing solid front.&apos; Recently, it became evident this explanation was not completely satisfactory and it is now evident that "crystal multiplication" plays an important role. This crystal multiplication occurs by separation of dendrite arms from growing dendrites,8?"&apos; and has been shown to be strongly influenced by convection.6, 10-13 Reduced convection results, for a given alloy, in longer columnar zone, larger columnar grains, and larger equiaxed grains.7, 12

Jan 1, 1968

By Martin F. Littmann

Inclusions of MnS and Fe3C have been introduced into single crystals of 3 pct Si-Fe to study their effects on recrystallization behavior and textures after cold rolling and annealing. The presence of MnS in (110) [001] and (111)[112] crystals inhibited primary grain growth and promoted secondary recrystallization but did not alter the texture significantly after annealing at 1200°C. The presence of Fe3C in (llO)[OOl] and (100)[001] crystals caused a refinement of the primary re crystallized grain size but did not promote secondary recrystallization. THE texture behavior of single crystals of 3 pct Si-Fe during deformation and recrystallization has been studied by numerous investigators. The early work of Dunn&apos; followed by Decker and Harker2 involved relatively small cold reductions. More detailed studies of Dunn3&apos;4 and of Dunn and Koh5&apos;6 involved a reduction of 70 pct and recrystallization at 980°C for several crystals. Walter and Hibbard7 studied a greater variety of initial orientations and sought to relate the textures to those of polycrystalline material. Attention was focused on the nucleation process during early stages of annealing and on surface energy effects in studies by Walter and Dunn8 and by HU.9&apos;10 One of the most extensive investigations has been reported by T. Taoka, E. Furubayashi, and S. Takeuchi.11 Most of this work has been conducted using relatively pure crystals with minimal amounts of precipi-tate-forming elements such as carbon, oxygen, sulfur, and nitrogen. Recently, however, S. Taguchi and A. Sakakura have observed that AIN precipitates can alter the recrystallization textures of rolled (100)[001] crystals.12 The present studies were initiated to determine effects of MnS and Fe3C precipitates on recrystalli-zation and grain growth behavior of rolled single-crystals of 3 pct Si-Fe. Both of these types of inclusions play significant roles in the recrystallization behavior leading to the formation of the (110)[001] or cube-on-edge texture in commercial grain-oriented silicon iron. It is well known that (110)[001] primary grains are formed by recrystallization of (110)[001] or (11 l)[ 112] crystals after cold reduction of about 60 pct or more. Crystals of these orientations, therefore, were selected for study of the effect of MnS in-clusions on grain growth. On the other hand, a major component of the texture of cold-rolled, polycrystal-line 3 pct Si-Fe is the (100)[011] orientation. The function of Fe3,C inclusions is of interest for this orientation. EXPERIMENTAL PROCEDURE The single crystals used are listed in Table I and were obtained from commercial Si-Fe alloy processed to produce (110)[001] and (100)[001] texture by secondary growth. The cube-on-edge material was 0.59 mm thick. Suitably large (110)[001] crystals 25 mm wide were selected and their orientations were determined using an optical goniometer. Etch pits for texture determination were formed by a ferric sulfate solution. The other crystals used in the study with (100)[001], (100)[011], and (111)[112] orientations were obtained from sheet which contained large grains developed from secondary recrystallization by a surface-energy driving force.13 Most crystals had a (100) plane very nearly parallel to the sheet surface and the rolling direction could be selected readily. The same sheet also contained a few crystals with (111) planes parallel to the sheet surface, these also being a result of growth by surface energy. The crystals selected from the sheet were about 25 mm wide and 0.25 to 0.28 mm thick. As shown in Table 11, the crystals already contained about 0.070 to 0.10 pct Mn. Inclusions of MnS were incorporated into crystal 36 in the following manner. The crystals were first sulfurized by holding them Table I. Initial Orientations of Crystals Crystal No. Initial Orientation Thickness, mm Special Treatment 34 (I10) [00l]* 0.59 None 36s (110) [001] 0.59 Sulfide precipitates added 30,40 (111)[Ti21 0.28 None 43s (III) [Ti21 0.28 Sulfide precipitates added 37 (100) [Oll] 0.30 None 37C (100) [01I] 0.27 Carbon added 41 (100) (01I] 0.25 None 41C (100) [OI11 025 Carbide precipitates added 42 (100) [OOl] 0.25 None 42C (100) [001] 0.25 Carbide precipitates added *Tilted 4 deg to r~ght about R.D. Table II. Compositions of Crystals Special Treatments Base Analysis ~ ______________________£________________Crys- Crystals Pct Si Pct C Pct Mn Pct S Pct N Pct Al tal Pct C Pct S 34.36 2.93 • 0.099 <0.005 - 0.0014 36S 0.011 30.37 to 42 2.78 0.0057 0.070 0.001 0.0008 0.0011 43S 0.022 37C 0.029 -41C 0.028 -42C 0.026 *Estimate 0.004 pct. Oxygen estimated <0.003 pct on all samples

Jan 1, 1970

By C. G. Dunn, F. Lionetti

W. G. BURGERS*—It seems almost certain that this investigation shows the way which finally, when more analogous data have been obtained, must lead to the understanding of many features of preferential growth-directions of crystals and of the occurrence of recrystallization textures. In this connection I should like to mention that Mr. Tiedema in my laboratory succeeded in developing an analogous method for preparing crystals in aluminum plates with a chosen crystal-lographic plane and direction parallel to the surface of the plate (to be published in Cryst. Ada). If such crystals were grown in high purity aluminum and test-pieces containing a few crystals such as the authors describe were prepared for this metal, it might be possible that due to the absence of growth obstructing particles, even in this low-melting point metal boundary displacements approaching equilibrium positions might be realized. With regard to the apparently marked drop in surface energy for orientation differences approaching zero degree, and orientation differences approaching those existing between twins, it seems of interest to remark that in aluminum a crystal growing at the expense of fine grained material cannot (or can only very reluctantly) absorb grains in either ap- proximately (within 5—10°) parallel or spinel twin orientation (May, Tiedema and Burgers, Nature (1948) 162, 740 and Cryst. Ada in press). Consequently with aluminum the method of preparing a crystal with a definite orientation does not succeed when the new crystal has to absorb its own texture; for example it is not possible to grow in a polycrystalline wire with a [lll]-texture a crystal with a [11 Indirection parallel to the wire axis (Tiedema: Cryst. Ada, in press). Finally I should like to mention the well-known fact (Burgers: Proc. Acad. Amsterdam (1947) 50, 723) that prolonged annealing of recrystallized nickel-iron sheet with cube-texture never succeeds in transforming this into one single crystal of the same orientation; if, by "secondary re-crystallization," large crystals are formed

Jan 1, 1950

By S. H. Ash

Mass production methods, although increasingly important for economic reasons, create new hazards, remove many hazards, and improve health and safety by reducing exposure and obtaining better supervision. Such methods must be efficient or be discarded. Skilled workmen are required who must be trained to utilize equipment that replaces picks, shovels, and explosives. The effects of working conditions on the health of workmen have long been evaluated in noncoal mines. Studies and action programs relating to environmental health hazards in the mineral industry have placed particular emphasis on dusts. The anthracite industry is conducting an action program on the problem of dust. Segments of the bituminous industry are now conducting similar investigations. An industrial hygiene survey of coal mining in the State of Washington has been conducted and the results published in 1949. (State of Washington, Department of Health, I. H. Bul letin 4.) Chest X rays were obtained from miners in the six major coal-producing counties. State Health Department mobile X-ray equipment was set up at most large mines. Participation was on a voluntary basis, and response was obtained from 70 percent. Important in successful mining safety programs are training programs for supervisors and workmen alike. These programs recognize that the employe is the focal point in injury prevention and are planned and function around him. During the war, industries had to compete with each other for workers and to obtain and hold good workers, working conditions had to be made attractive. The average age of the mine worker increased, and, contrary to what many expected, mining injury rates decreased rather than increased. To attract competent workers, risks to life and limb, as well as laborious tasks, have to be reduced, and an experienced worker is indispensable for safety. Young men are returning to modernized mines. Mass production methods and equipment are more to their liking; jobs are more remunerative, demand action, and require special training and skill that give them the mark of a craftsman. Such workmen can be taught safe methods.

Jan 1, 1950

By D. G. Westlake, D. T. Peterson

The saturation solubility of thorium dihydride in thorium was studied by saturation of samples and subsequent analysis. The solubility increased from about 1 at. pct at 300°C to above 20 at. pct at 800 °C. Over this temperature range the log of the solubility was a linear function of the reciprocal absolute temperature for thorium of good purity. The heat of solution of thorium dihydride was found to be 7.9 kcal per atom of hydrogen in crystal bar thorium and 6.6 kcal per atom of hydrogen in Ames thorium, The important effect of hydrogen on the physical and mechanical properties of many metals is receiving increasing recognition. The basic physical and chemical data necessary to help explain the observed effects of hydrogen on the mechanical proper ties of metals are all too often not available. The solubility of hydrogen in thorium metal was determined to provide a portion of this basic data for the thorium-hydrogen system. The absorption of hydrogen by thorium metal and the formation of thorium hydrides was studied by several investigators, beginning in 1891, and their work is summarized in Gmelin&apos;s Handbuch.1 No effort was made to determine the extent of solid solubility in the metal in these early investigations and the impure metal available made interpretation of the results uncertain. Nottorf2 reported the results of a careful study of pressure-composition isotherms for the thorium-hydrogen system. The principal interest in this work was in the composition and dissociation pressures of the thorium hydrides. Mallett and campbel13 reported the pressure-composition isotherms for the thorium-hydrogen system up to the composition of thorium dihydride. The saturation solubility of thorium dihydride in thorium was reported to be 13 at. pct at 650°C and 23 at. pct at about 900° C. Mallett and Campbell used thorium metal which had been prepared by the calcium reduction of thorium tetra-fluoride or thorium oxide. The results obtained with thorium of these two types agreed within the experimental error. PROCEDURE AND MATERIALS Procedure—The method used to determine the solubility was to saturate a sample of thorium with hydrogen and analyze a portion of the saturated sample. This method was chosen rather than a determination of pressure-composition isotherms since it was much less time consuming and could be applied at temperatures at which the equilibrium hydrogen pressure was too low to measure. The

Jan 1, 1960

By Irving M. Symonds

COMPAÑIA Minera de Peñoles, S. A., at its Avalos unit operates a lead-zinc concentrator having a capacity of about 600 short tons per day. Lead and zinc concentrates are made by flotation methods. The concentrator is at Terminal de Providencia, in the state of Zacatecas, some 70 miles south of Saltillo, Coahuila. The Peñoles-Avalos railroad operating between the plant and Estacion Avalos, a distance of 6 miles, makes connections with the Coahuila and Zacatecas railroad, which in turn connects with the Nacionales de Mexico at Saltillo. The three railroads are each of different gauge, requiring the transfer of all supplies and concentrates at each junction. The mill operates on company ores, on ores from leased mines, and as a custom mill. The custom business is very small. The lead concentrates are shipped to company smelters at Monterrey, Nuevo Leon and Torreón, Coahuila. Since the European war, all zinc concentrates have been shipped to the United States. ORE TREATED The major source of ore supply is a group of four mines owned or leased by the company, some three miles south of the mill in the mountains, from which the ore is delivered to the mill by a gravity aerial tramway. Custom ore comes in by rail. The ores occur in chimneys. The upper levels contained oxidized siliceous ores of lead, copper, silver and gold, with varying amounts of zinc. These ores were direct-smelted. In the first two years of operation a good deal of the tailing loss was caused by the oxidized content of the ores milled. Much of the ore in the transition zones between the oxides and sulphides was not mined. The ores now being milled are clean, hard sulphides in a limestone gangue, with only occasional contamination of oxides. The lead and zinc sulphides are of coarse structure and are freed even above flotation sizes. The galena is usually "steel" colored, easily and quickly floated. When there is any oxidation, it is usually on the coarsest crystals. The zinc minerals vary a good deal in color; a resin sphalerite predominates but there are varying shades of brown marmatites. On an average, the zinc sulphides contain 64 per cent zinc. The only common copper mineral is chalcopyrite. Little is known of the occurrence of gold and silver. Waste minerals are mainly limestone and pyrite, both of which are barren. The ores vary from 20 to 35 per cent pyrite. Mill heads for the year 1940 and the first eight months of 1941 are given in Table I. [ ]

Jan 1, 1942

By W. A. Roper

Since 1950, several papers have been published which have described various methods for studying mobility ratio effects. The methods which have been described for studying mobility ratio effects include X-ray shadowgraph techniques, stepwise potentiometric model procedures, stepwise numerical procedures, gelatin model studies and fluid mapper model studies. The purpose of this paper is to describe a procedure for using a resistance network for studying mobility effects. DESCRIPTION OF APPARATUS The basic unit of the experimental model consisted of a network of 840 resistors fastened to a sheet of black Lucite which was mounted on a wooden frame, Fig. 1. The dimensions of the Lucite sheet were 36 X 36 in. The resistors were fastened to the Lucite sheet at mesh points by means of snaps. The mesh points were arranged in a square pattern, 30 X 30 in., spaced at intervals of l1/2 in. The snap fasteners permitted several resistors to be "stacked" in parallel. By adding additional resistors to the basic unit, the specific resistance on each side of the flood front could be varied. The square network of resistors represented one of four symmetrical elements of a five-spot well pattern. The current input was analogous to an injection well and the current output was analogous to a production well." The power supply was essentially a full wave transformer-rectifier system for converting alternating-current into direct-current. The DC voltage could be varied from 41.43 to 290 v in steps of 41.43 v by selecting the proper outlet jacks. The major components of the power supply were: a Triro power transformer, R 11-A; a dual 5Y3 vacuum tube; two gas filled OD-3 tubes; and a Triplett voltmeter, model 227-1, range 0 to 500 DC v. The voltages at the mesh points were determined with a Keithley electrometer, model 210, No. 185, manufactured by Keithley Instruments, Cleveland, Ohio. A Heathkit vacuum tube volt-

By Lewis A. Delano, Harold Rabling

It has been generally recognized that, owing to the extreme friability of galena, fine grinding has a tendency to cause excessive sliming of the mineral, so operators of lead mills have attempted to avoid this condition by commencing concentration at as coarse sizes as any mineral is freed. Jigging has been the basis of the milling process, making a clean coarse concentrate and a large amount of tailing, which was considered sufficiently low-grade to be rejected. However, developments and improvements in concentration processes are everywhere changing the low-grade tailing of yesterday into material worth re-treating today. Investigations of the work of the Hancock jig on the Bonne Terre ore have shown that the best results to be expected will give a tailing assaying 0.75 per cent. lead; the average for all conditions and grades of ore will be between 0.80 and 0.90 per cent. By crushing the jig tailings in ball-mills and retreating by tables and flotation, a tailing of considerably lower grade can be made; the problem then becomes an economic one of increased crushing costs versus higher recovery. In considering the entire elimination of jigging, the increascd smelting charges due to a greater amount of slime galena will be counterbalanced by the lower operating cost, increased recovery, and the many advantages of a simpler flow sheet. In developing these problems in the Bonne Terre mill of the St. Joseph Lead Co., a long series of tests has been carried out covering every stage of crushing and concentration, and a large number of possible flow sheets were considered and tried. Only the final results and a few comparisons will be given here. At the same time, a careful and detailed cost-keeping system has enabled us to compare milling costs with the various Bow sheets, and to calculate the economics of the problem with great accuracy. Concentration Problem The ore occurs as widely scattered deposits of galena disseminated through limestone; it has a specific gravity of 2.8 and the following composition: Pb, 4.00 per cent.; Fe, 3.00 per cent.; Zn, 0.32 per cent.; S, 3.10 per cent.; MnO2, 0.73 per cent.; SiO2, 4.20 per cent.; Al2O3, 3.20 per cent ; CaO, 28.60 per cent.; MgO, 16.85 per cent.; CO2, 36.00 per

Jan 1, 1922

By Y. Baskin

Solid-solubility relationships in the Pseudobinary systems UAS-UP, UAs-US. UAS-UC, aid UAs-UN were investigated. The first two systems exhibit complete mutual solubility, whereas the component compounds in the other two systenzs are immiscible. The above information, together with solid-solubility data joy six additional pseudobinary systems , were analyzed for compliance wilh the Hurrze-Rothery rules for rnetallic systems. The relative size difference of the component nonmetal atoms was found to be the dopainant jactor determining the extent of solid solubility between the NaC1-type uranium compounds. The anionic and covalent radii of the nonmetal atoms appear to be inadequate for these systems, but compuled radii based on rare earth compounds yield consistent results for the uranium compounds. THE actinide elements, like metallic elements of the transition and rare earth series, readily form binary compounds with nonmetallic elements of groups IV, V, and VI of the periodic table. Of particular importance are the NaC1-type equiatomic compounds with carbon, nitrogen, sulfur, phosphorus, and arsenic. The uranium members of this family of compounds have high melting points, are essentially stoichiometric, and exhibit various amounts of mutual solubility. Thus, they are of interest for investigating the factors governing the extent of solid solubility. Previous investigators have determined the solid-solubility limits in the pseudobinary systems between the compounds UC, UN, US, and UP. Anselin et a1 .&apos; reported complete miscibility in the system UC-UN. Baskin and shalek 2 and Allbutt et a1.3 reported that UP and US exhibit complete mutual solubility. Shalek and white4 reported partial miscibility in the system US-UC. At 1800°C the maximum solubility of UC in US is 40 mol pct, but that of US in UC is 4 rnol pct. shalek5 found limited solubility in the system US-UN; the maximum solubility of UN in US is 11 rnol pct at 1800°C, while that of US in UN is only 0.3 mol pct. White and askin 6 found very limited miscibility in the system UP-UC at 1800°C. Approximately 7 mol pct UC is soluble in UP, but there is no solubility of UP in the monocarbide. Phase relations in the pseudo-binary system UN-UP were investigated by askin.&apos; Approximately 0.7 mol pct UN is soluble in UP at 1800°C, while UP is immiscible in UN. The present study was carried out to explore the extent of terminal solubility in the systems UAs-UC, UAs-UN, UAs-US, and UAs-UP. This information, combined with existing data, provided a sufficient basis on which to determine the factors governing solid solubility in pseudobinary systems containing NaC1-type uranium conpounds. I) EXPERIMENTAL 1) Materials. The compounds UC and UN were obtained from the Kerr-McGee Corp. and United Nuclear Co., respectively. The US, UP, and UAs were synthesized by reacting finely divided uranium with H2 S, pH3, or AsH3 gas at low temperature (300° to 500°C), followed by homogenization in a vacuum at moderately high temperatures (1400° to 1700°c).8-10 The materials were essentially stoichiometric, with the exception of UC, which exhibited a C/U ratio of 1.05. Oxygen was the major contaminant in these compounds, ranging from 0.05 wt pct in US to 0.30 wt pct in UC, and it was generally combined with uranium to form UO2. The UO2 content in these materials was usually of the order of 1 wt pct, and did not exceed 2 wt pct. Furthermore, no evidence was found for a high-temperature reaction between uranium dioxide and any of the compounds. Chemical analyses of equilibrated compositions in the systems UAs-UP and UAs-US showed that the non-metal atom to uranium ratios averaged about 1.01, and that the oxygen contents ranged from 0.06 to 0.22 pct. However, the small deviations from stoichiome-try or the presence of minor oxygen impurities do not invalidate the conclusions to be drawn from this study. 2) Experimental Procedures. The component compounds in powdered from were blended in the desired proportions for 5 hr in the ball mill that consisted of stainless-steel balls in a plastic container. Chemical analyses indicated very little metallic pickup from the blending operation and virtually no increase in oxygen content. The pellets were pressed in a 0.270-in.-diam steel die under 40,000 psi pressure. One wt pct of stearic acid dissolved in CCl 4 served both as a binder and as a die lubricant. Chemical analyses revealed that the stearic acid left no carbon residue in the sintered samples. The pellets were sintered in vacuum in an unsealed tantalum crucible. The temperature, measured with a calibrated optical pyrometer, was maintained at 1800" + 30°C for 3 hr. This was sufficient time for attaining equilibrium as no change occurred in either the lattice parameters or the sharpness of the X-ray patterns when samples were annealed for longer periods of time. The pellets were cooled with the furnace. Debye-Scherrer powder patterns were taken at room temperature with a 114.59-mm-diam Norelco powder camera and CuKor radiation (CuGI = 1.5405A). Unit cell dimensions were determined from a Nelson-Riley extrapolation to the high-angle reflections. The values for were precise to k 0.001A. 11) RESULTS X-ray and met allographic investigation revealed that complete mutual solid solubility exists in the pseudobinary systems UAs-UP and UAs-US. The lattice parameter vs composition plots, Fig. 1, show a

Jan 1, 1968

Agnico-Eagle Mines Ltd. comprises a Gold Division at Joutel, Quebec, and a Silver Division at Cobalt, Ontario. In 1979 the Silver Division milled 41,700 mt (46,000 st) of ore at a recovered grade of 139 g per mt (4.06 oz per st) for a production of 5,816 kg (187,000 oz) of silver. The 100 -year -old mining, camp of Cobalt has long been noted for its high-grade silver ores, and now seems to be on the threshold of being revived with several companies operating in the area. In 1979, the Gold Division milled at the rate of 27,200 mt per month (30,000 st) and processed 333,000 mt (367,000 st) at a grade of 6.58 g per mt (0.192 oz per st) with a mill recovery of 91.670 to produce 2,013 kg (64,700 oz) of gold. The average total cost per ton milled was $22.10 per mt ($20.05 per st) which was $3.66 per g ($1 13.90 per 0s). These figures make Agnico-Eagle one of the lowest cost producers in North America. Gold occurrence in the Joutel ore is fine-grained and contained within sulfide facies composed mainly of pyrite with minor pyrrhotite. Two underground mining methods are employed with long hole stoping accounting for about 75% of the ore mined and shrinkage stoping the remainder. Ore from underground is hoisted into a 545 mt (600 st) coarse ore bin from where it is conveyed to a 45 mt (50 st) surge bin ahead of the 10-51 Hydrocone crusher. Crushed ore is then screened to make a 13 mm (112 in.) product with the oversize being recrushed in a 7-60 Hydrocone. Mill feed is conveyed to two 900 mt (1,000 st) fine ore bins. The Hydrocones were installed as part of a new crushing plant in March of 1980 and have contributed substantially to an increase in mill capacity. Space has been left to install a third crusher in the future. The fine ore bins discharge to a 2.75 m by 3.66 m (9 ft by 12 ft) rod mill, followed by a 3. 7 m by 5.5 m (12 ft by 18 ft) ball mill in closed circuit with a Krebs 380 mm (15 in.) cyclone to produce a 7070 minus 37 micron (400 mesh) .flotation feed. This pulp is first treated in a 34 cu m (1, 200 cu ft) Maxwell flotation cell and then in an additional twelve 2.8 cu m (100 cu ft) cells. Combined flotation concentrates are reground to 9070 minus 37 microns (400 mesh) in a 1.8 m by 4.9 m (6 ft by 16 ft) ball mill in closed circuit with a single Krebs 254 mrn (10 in.) cyclone. Flotation tailings are sent to the tailings dam. Reground concentrates are then aerated with lime to a single Pachuca and thickened in a 16.75 m (55 ft) diameter thickener with the addition of diesel fuel to render any activated graphite inert to adsorption of

Jan 1, 1981

By R. A. Flinn, John T. Norton

A CONSIDERABLE number of experiments in recent years have definitely established the fact that the internal friction or mechanical hysteresis of a metal under cyclic stress is a property that is highly "structure sensitive." Because of this fact, it has been suggested that an observation of this property, which often is referred to as "damping. capacity," might be a useful indicator of structural. changes taking place when a metal or alloy is subjected to any of a number of metallurgical treatments. Damping capacity is of interest to both engineer and metallurgist, but from a rather different point of view, and the information that each desires from such observations is of a different nature. The metallurgist is in search of various external indications of changes taking place in the interior of a metal; changes which are in themselves not directly observable. Even if the observed phenomenon cannot be explained in fundamental terms, it may be empirically related to certain characteristics of the material and prove of real value in research. Internal friction os mechanical hysteresis occupies such a position, and, although it is nor well understood in terms of basic metallic theory, an observation of itt changes can serve in a very useful capacity. Of course, there is nothing new in the measurement of damping, but the use of this property in metallurgical research constitutes a vast field, which has received all too little attention: The present work is essentially of an exploratory nature in this field and is an attempt to evaluate the process as a research tool. The phenomenon of age-hardening was chosen as a typical example of a structural change and one method of measuring damping was examined in considerable detail.

Jan 1, 1938

By Richard H. Ross

A broad definition of&apos; "Mill Design" might cover everything from the first tentative choice of general process to the final structural details for construction. The first phases are mainly concerned with metallurgy and economics and the final stages with the mechanics of putting the selected equipment together into an integrated plant. It is the purpose of this article to discuss only data, derived from laboratory testing, that contributes directly to design of the milling plant itself, and only the plant design phases that are influenced by laboratory testing. Most ore beneficiation testing is devoted to determining recoveries, grades of products, elimination of impurities, reagent and supply requirements, etc. having little to do with physical plant design although these factors are of prime importance in the evaluation of a mining project.

Jan 3, 1964

By E. M. Wise

IT is known qualitatively that the recrystallization behavior of platinum is dependent upon the amount and particularly the nature of impurities present, the amount of prior cold-work and the annealing time and temperature, but published data are limited. A study of the effects of cold-work and annealing temperature on the hardness of a sample of very pure platinum was undertaken to supply part of this information. CONCLUSIONS 1. The platinum used in the experiments had a probable platinum content of 99.99+ per cent, and had the following mechanical properties in the completely softened condition: Vickers hardness number, 39.4; ultimate tensile strength, 19,340 lb. per sq. in.; proportional limit, very low; elongation, 37.5 per cent in 2 inches. 2. The effect of cold-rolling on the hardness is shown in Fig. 1. The hardness increases rapidly up to 10 to 15 per cent reduction and more slowly up to about 75 per cent reduction, beyond which it increases more rapidly. 3. The recrystallization temperatures for a 15-min. anneal, after cold-rolling 19, 39.5, 50.8, 66, 80.5 and 89.5 per cent reduction in thickness, are approximately 765°, 700°, 635°, 600°, 545° and 425°C., respectively. 4. The recrystallized grain size of this platinum is a function of the percentage of cold reduction, being larger the lower the percentage of cold-work. 5. Little or no grain growth resulted from subjecting recrystallized samples to higher temperatures or annealing for longer times.

Jan 1, 1940

By H. E. Nold

THE raw materials of the ceramic industry are mostly clays. This raw material is ground, water is added and the mixture pugged into a moist, plastic, rather stiff mass. From this mass the desired units of manufacture are made (bricks, hollow building tile, sewer .pipe, etc.). These units are dried; then placed in kilns and heated until the desired degree of vitrification is obtained.1 For firing ceramic ware, two distinct types of kilns are used; namely, periodic and continuous tunnel. PERIODIC KILNS Periodic kilns are those ordinarily seen in a brick plant. They are either round or rectangular. The raw, dried, formed ware is piled or set in the kilns to depths frequently exceeding 10 ft. The kiln is heated until the ware is matured, then gradually cooled sufficiently to allow men to remove the ware; then the cycle is repeated. The time duration of the cycle may be more than two weeks.

Jan 1, 1933

By E. C. Truesdale, W. K. Waring

The Research,Division of The New Jersey Zinc Company (of Pa.) has conducted, over a period of years, numerous tests of the reducibility of various zinc ores and the reactivity of various kids of coal, using a number of different experimental methods. Most of these tests have involved the reduction of mixtures of ore and coal. In such cases the following simultaneous reactions are believed to be mainly responsible for the production of zinc, as was shown by Bodenstein&apos; some years ago: ZnO + CO = Zn + CO2 [i] C + COj = 2CO [2] Each of these reactions is dependent upon the other for the supply of CO and COz, respectively, and the over-all rate of formation of zinc vapor will be determined by the slower of these two reactions. An analogous pair of reactions sometimes of importance is: ZnO + He = Zn + HZO 13] C + Hz0 = CO + He U3 While it is possible to obtain an indication of the relative reducibility of various ores, or of a fine versus a coarse Ore, by testing them with a given coal, and while coal reactivities may be measured in a corresponding manner, a more direct determination of relative reaction rates is possible by carrying out the desired reactions, such as I and 2, separately and under reproducible conditions. It is one purpose of this paper to present some of the results that have been obtained by the latter method. C. G. Maier2 discusses the relative rates of reactions I and 2 and concludes that while at relatively low temperatures reaction I is faster than reaction 2, this difference becomes less with increasing temperatures, although at smelting temperatures reaction is still the faster. He also says (p. 48), "At temperatures . . . be- -tween 1100&apos; and 1300°C., . . . the zinc oxide reduction reaction is intrinsically more rapid than its physical limitations; that is, it is limited by gas diffusion rates.&apos;&apos; In the course of numerous reactivity tests involving the separate use of reactions and I and 2, we have obtained data that show by direct experiment, we believe for the first time, the correctness of Maier&apos;s statements concerning these reactions. We also include data on the relative rate of reaction 3, involving reduction by hydrogen. Finally, some interesting results obtained by carrying out the reduction of &apos; a zinc ore-coal briquet in streaming atmospheres of nitrogen, carbon monoxide and hydrogen, respectively, are presented.*

Jan 1, 1944

By Margaret V. Doyle, R. W. Powers

INTERNAL friction measurements, carried out as functions of temperature, have been used extensively to obtain data on the mobility of interstitial impurities in the Group V metals, vanadium, colum-bium, and tantalum. For a given frequency of vibration, the internal friction peaks at a temperature which depends principally on the particular metal and interstitial impurity. Relaxation times and corresponding activation energies are determined from a knowledge of such peak temperatures for various vibration frequencies. These experimentally determined relaxation times are related to the average jump frequencies of the interstitial impurity atoms using the model of Snoek1 and can be related to macroscopic diffusion coefficients as shown by Polder.2 In these Group V elements, the impurity whose diffusion rate has been the hardest to pin down by the internal friction technique has been carbon. The experimental difficulties associated with carbon in these metals were not evident in the earliest investigation carried out by Ke on tantalum.3 The carbon peak was thought to occur near 140°C at 1 cps on the basis of the enhancement of the height of this peak measured on specimens which had been coated with colloidal carbon and heated in vacuo at 1200°C. Presumably on the basis of similar evidence, Wert identified a peak also near 140°C at 1 cps in columbium with the diffusion of carbon in that element." Later, the difficulties of admitting carbon into these metals without simultaneously introducing oxygen were pointed out by Ang and Wert- nd by Marx, Baker, and Sivertsen.6 The latter suggested that the peaks attributed to carbon in tantalum and columbium might arise from the presence of traces of oxygen, adventitiously absorbed during the carburization. Such suspicion was confirmed, at least in tantalum, when it was found possible to prepare C-Ta specimens without contamination by oxygen. Specimens sci prepared, aitnough high in carbon content, gave no evidence of a damping peak near 140°C.7 Recently, the authors were able to Show that carbon diffuses in tantalum at a rate only slightly slower than that for nitrogen.8 At 1 cps, the carbon peak lies at 34g °C, only a few degrees above the nitrogen peak at 341 °C. However, the two could be distinguished by a different stability with respect to aging at 400 °C and by a different dependence of peak height on solute concentration. On the basis of this experience with tantalum, it appeared worthwhile to search also for a carbon peak in columbium in the vicinity of the nitrogen peak." In this report, the location of the carbon peak in columbium is made known and its position relative to the nitrogen peak is compared with the authors&apos; previous findings in tantalum. In addition, a second source of internal friction seen only in specimens of very high purity is discussed. Columbium was obtained from the Fansteel Metallurgical Corp. as either 30 or 40 mil diam stock. The manufacturer gives the following analysis as typical of this material: 99.4 pct minimum Cb, 0.10 pct maximum C, 0.5 pct Ta, 0.04 pct Ti, 0.02 pct maximum Si, and 0.01 pct maximum Fe. Wires 13 in. long were degassed near 2200°C for 4 to 16 hr in an ultimate vacuum better than 2.10" mm Hg in an apparatus described previously.8 This treatment reduced the oxygen and nitrogen damping peaks observed in the as-received material to less than 0.0001 in Q-1 above background. The latter value varied somewhat from specimen to specimen in the range 0.0004 to 0.0008, depending chiefly on the wire diameter and the frequency of vibration. The high temperature evacuation left the specimen in a rather soft condition, the Vhn being reduced to 40 from a value near 121 in the as-received conGi~iur~. The gram size was about the diameter of the specimen. After outgassing, specimens were loaded with carbon by absorption of such hydracarbons as methane or ethylene. Carbon was also added to a few speclrnens by heating them at

Jan 1, 1958

Fifty to 75 million years ago, hydrocarbon-bearing rocks were formed in the Green River formation of Colorado, Wyoming and Utah. The hydro- carbons can be extracted from these rocks, marl- stone but misnamed oil shale, after crushing and intense heating. At about 900°F the marlstone decomposes to produce liquid shale oil. A press release from the Colony Development Co. describes a process which may permit, for the first time, economically feasible access to shale oil. Shale oil has resisted economic extraction for almost three centuries. According to the USBM, a patent was issued as early as 1684 in England to produce "oyle from a kind of stone". France produced oil from marlstone in 1838 and a dozen years later, Scotland started an oil shale industry, producing kerosine, that lasted nearly 100 years. In both countries, the process involved crushing the stone and retorting it to decompose the kerogen-a long and costly process at that time. In 1859, Edwin L. Drake brought in the first oil well in Titusville, Pa., and shale oil faded into oblivion.

Jan 8, 1965

May 219t, 1872. THE Institute assembled in the rooms of the Geographical Society at the Cooper Union, Tuesday evening at 8 P.M. President Raymond called the meeting to order, and introduced Mr. Abram S. Hewitt, who welcomed the Institute to New York. President Raymond, in behalf of the Institute, replied. The President then read the following report of the Council for the past year. The Council respectfully report that the American Institute of Mining Engineers has held four meetings-at Wilkes-Barre, Bethlehem, Troy, and Philadelphia, respectively-all of which have been well attended, and socially and professionally most successful. The proceedings of these meetings having been published in the Engineering and Mining Journal, and sent to all members and associates, are sufficiently well known. Forty-four papers, by twenty-six authors, have been read. These papers embrace s wide range of subjects, and prove the practical character of the proceedings of the Institute. The finances are in a satisfactory condition. By the report of the Treasurer it appears that $1290.10 have been received, $519.90 expended, and that $770.20 now remains in the treasury exclusive of fees for 1872. This fund, it is hoped, will be so increased by voluntary subscriptions as to enable us before long to issue s volume of our most important transactions in a permanent form. The Council has made a favorable arrangement with the Scientific Publishing Company, publishing the Engineering and Mining Journal, by which that journal became the organ of the Institute for the first publication of the proceedings, papers, and notices to members. This arrangement it is proposed to continue through the present year unless the Institute shall otherwise direct. It is not intended to supersede the publication of an annual or occasional volume, but to maintain an interest in the Institute, and to serve the convenience of members while our funds do not permit s more ambitious publication.

Jan 1, 1873