Search Documents

By E. A. Gulbransen, W. S. Wysong

The behavior of tungsten and its surface oxides in oxidizing and reducing atmospheres and in high vacua at elevated temperatures is a question of considerable technical importance. The use of tungsten as a a Or as an important component in alloys in high temperature Oxidizing atmospheres has been limited because of the unprotective nature of its oxide film and the volatility of its oxide. This paper will present results of a micro-balance study of the following problems: (1) the oxidation behavior in the ternperature range of 25 to 550°C (') the reduction with pure hydrogen Of thin Oxide films formed On tungsten, and (3) the volatility Of thin Oxide films On tungsten. Tungsten is an interesting metal to study for the following reasons: (1) although the Oxide to to ratio is greater than one, the oxide is not considered protective, ('1 the meta1 readily Oxidizes at temperatures from 30" to 55o°C (3) the oxides WO² and WO³ are reduced at temperatures as low as 500°C. by hydrogen, and (4) the Oxide WO3 is volatile at temperatures from 800 to 1100°C. Literature The oxidation of tungsten in its thin film range has not been studied critically. In the thick film range Dunn3 has made the only systematic study. He found the oxidation rate to obey the parabolic rate law in the temperature range of 700 to 900°c. The temperature variation of the oxidation rate constant was found to follow an exponential law of the Arrhenius type. An inflection was noticed in the temperature plot of the rate law constant at 850 to 900°C. This was attributed to a phase change in the oxides, Schei14 has studied the oxidation rate at 500 and 700°C over long periods of time and found a linear rate law. This result was interpreted as evidence for the presence of a nonprotective film. Pilling and Bed-worth's5 analyses of the oxide volume to metal volume ratio would indicate that a compact protective film should form. McAdam and Geil6 have studied the oxidation of tungsten in the thin film range using the interference color method. A parabolic rate law was found. Their curves showed that tungsten oxidizes faster than nickel but more slowly than iron. The lattice structures found in the oxidation of tungsten surfaces have been studied by Hickman and Gulbransen.? They have reported that WO3 is the stable oxide in contact with the metallic substrate up to approximately 600°C while wo³ forms first at 7oo°c. Hagg and Magneli8 have recently reported a study of the lattice structures . observed in the tungsten oxidcs using the X-ray diffraction method. In addition to an a-phase WO3 and a '-phase WO2, they reported the existence of two new phases. A 8' phase, homogeneous between

Jan 1, 1949

By W. M. Yim

Experimental results are presented which indicate that transverse striations in horizontal zone-leveled Bi-Sb alloy crystals are due to irregular growth rate resulting from thermal fluctuations in the melt (Iring gowth. Thc thermal fluctutations arose from two different sources. The first type was brought about by periodic fluctuations in the furnace temperature. The second type can be attributed to turbulent therrrol conlcclion in the trzelt near the solid-liquid inteyace. Tile arrzplitlcde ond fvequency of the tetiperaticre fluctlrations vesultity from llle lhevnal con1,ecrrell. The striation spacings in Lhe crystals covvelale well with the periodicity 0.f the tempevature flueluatiors. Altliough the strialiors represenl corrlpositiozul inhoiHogeneity oh a rzicroscule, less than f.z cil. be1 S6 in Best's as deterrirzed by electron-pro be chalq'sis, the slriations roerre fbund to ILUL' no rrleusuanble effect on electical vesistirity rwr on weak field macgnetoresistance of. the Bi-Sb a1lu.y in the ternpevutue ),unge 4.Polo 300°K. DURING the course of an investigation on the horizontal growth of semimetals,' it was found that crystals of Bi-Sb alloys contained many closely spaced parallel arrays of striations. These striations occurred perpendicular to the growth direction and parallel to the solid-liquid interface. We shall refer to them as transverse striations, or just striations'', to distinguish them from lineage substructures or longitudinal striations which form parallel to the growth direction and have been known to be associated with cellular structures.' Similar transverse striations have been reported previously to occur in other materials prepared by horizontal growth: metals,4 semiconductors,5 as well as their alls. - Various methods of crystal preparation have apparently little effect on the occurrence of the transverse striations. They form whether the crystals were grown by the vertical Czochralski technique, withe1' or without'3- rotation, or by the horizontal zoning methd.- Thus, the transverse striations are not limited to any one class of materials, nor to any particular method of preparation. It is likely, therefore, that all of the observed transverse striations may have some common cause. Previously, workers agreed that periodic changes in the growth rate bring about the striations. However, no agreement exists as to the origin of the growth-rate fluctuations. Some attributed the discontinuous growth to a purely external cause, such as fluctuations in the furnace temperature, jerky motions in the crystal pulling mechanism, or a nonsymmetrical temperature distribution in the melt (in the case of crystals grown by the Czochralski technique with rtation). Others looked for the cause in some fundamental property of the growth process itself. For instance, a certain degree of supercooling is required to initiate growth from the melt. But, with further growth, the degree of supercooling decreases because of the liberation of the heat of solidification at the solid-liquid interface. Thus, crystal growth would be brought to a halt until sufficient supercooling is resotred and the cycle begins again.3'11 According to this model, periodic fluctuations in the melt temperature should exist at the solid-liquid interface. Since the periodic fluctuations in growth rate would result in changes in the segregation coefficient of solute atoms, crystals containing the transverse striations may, in some cases, show a periodic impurity fluctuation along the length, resulting in a degradation of electrical properties. The resistivity striations in doped germanium'9-10 or lnsbB are well-known examples of this microsegregation. The present work was undertaken to explain the exact origin of the transverse striations, and to assess the extent of their effect on chemical homogeneity as well as on electrical properties of Bi-Sb alloy crystals. Results from our previous study of the crystal growth of Bi-Sb alloys1 indicated that the transverse striations may arise from the temperature fluctuations in the melt during growth. This paper will show that the melt temperature fluctuations are indeed responsible for the occurrence of the transverse striations. I) EXPERIMENTAL Although the transverse striations have been observed in all slow-grown Bi-Sb alloys across the entire compositional range, we selected a composition, Big3Sbs, for the present study in view of the extensive data available on the crystal growth of this alloy from a previous study.' High-purity bismuth and antimony, both a 6-nine grade by the manufacturer's emission spectrographic analysis, were used throughout. Independent mass-spectrographic analysis showed, however, that the starting materials were more nearly a 5-nine grade. each containing metallic impurities of approximately 10 ppm atomic. In zone-leveled Big5Sb5 alloys, the total metallic-impurity content was slightly lower, about 7 ppm atomic, indicating that some degree of purification was achieved during the growth. None of the electrically active impurities, such as tin and lead (acceptors) and tellurium and selenium (donors), were present in significant quantity in undoped Bi95Sb5. Typical analysis of the undoped Bi95Sb5 alloy is shown in Table I. Nonmetallic impurities, such as carbon and oxygen, were detected, sometimes as much as 100 ppm, in both the starting materials and the zone-leveled alloys: but the data were only qualitative. Temperature fluctuations in the melt were monitored over 1 or more days by means of a 5-mil chromel-

Jan 1, 1967

By Walter S. Weeks, Vitaly S. Grishkevich

Considerable difference of opinion seems to exist as to whether the rate of air flow when a fan is placed on a given duct should be determined by the use of static pressure or total pressure characteristics. A little study will show that both methods are correct. Assume that a fan is connected to a duct by an expansion piece as shown in Fig. 1, and that steady flow is established. Considering the atmospheric pressure as zero pressure, let the static head at the outlet of the fan be h and the velocity at this point be vl. The total head at the outlet is then h + „"• The total head at this point must be equal to the total head at the end of the duct plus the losses that have occurred between the two points. Left be the friction loss in the straight duct, s the shock loss in the dif- fuser, and v2 the velocity at the end of the duct. Then ig. 1.—Fan on duct. A curve showing the value of the left-hand side of the equation for different rates of flow is the total pressure characteristic of the fan, while a curve showing the value of the right-hand side is the total pressure characteristic of the duct. If these two curves are plotted on the same chart, the intersection indicates the rate of flow when steady flow is established. We may look at this problem in another way. The static pressure at the outlet of the fan is the static pressure of the fan and it is also the static resistance of the duct from that point to the end. The friction in the straight duct is f. If the duct were the same area as the fan outlet, would be the static resistance of the whole duct system. In the present case, however, this resistance is decreased by the change of velocity head into static head in the expansion piece. If conversion were perfect, the static pressure recovered would be

Jan 1, 1931

By M. E. Wadsworth, R. L. Pearson

THE dissolution of UO, in carbonate solutions can occur only il the tetravalent uranium is oxidized to the hexavalent state. The carbonate system is of particular interest because it provides a means whereby the oxidized uranium may be dissolved by forming the complex ion UO,(CO3)3-1. In the presence of oxygen the over-all reaction may be written UO+1/2O,4CO3T+2HCO2UO,(CO4)11+H2O [1] UO, was used in this study because it could be obtained in high purity and also because it is representative of the most refractory of the primary uranium minerals. The mineral ulrichite is the natural counterpart of the synthetic UO, used. The kinetics of the leaching of UO, should be similar for any of the uraninite type minerals. A pressurized system was used not with the hope it could be extended to commercial systems as a primary purpose but simply to provide the means whereby important temperature and pressure parameters could be varied for the evaluation of the kinetic processes. The importance of such pres-

Jan 1, 1959

By Thomas Egleston

The copper-bearing rocks of Lake Superior are composed of a series of metamorphic rocks, comprised under the names of amygdaloid and conglomerate, in which the copper and silver found with them are pseudomorphs. These rocks, generally, have Well-defined walls which cause them to separate easily. Generally, the country rock is sterile, but it occasionally rises into the copper-bearing rock, and then carries copper. Usually, the amygdaloids carry copper, and the greenstones or melaphyres which encase them do not. There is a very generally received opinion that the copper in these beds occurs in shoots. This does not appear to be proved, though the opinion seems to have some foundation from the experience of the Calumet & Heela Mine, where a body of poor rock has been left, which, on the mine map, shows a general direction. The theory may be true of that individual mine, but too little work has been done in the other mines to draw any decided conclusion. The copper is very unequally disseminated in the rock, if any given piece be taken as an example, but, if the whole copper-bearing series be considered, its distribution is uniform. It may prove that there are certain directions in which the copper has been deposited more abundantly than in others, and these may be found to correspond with certain geological causes, but up to the present time the knowledge gained is not sufficient to warrant any general conclusion. These rocks are supplemented by a series of true fissure veins, of which there are several systems, making the amount of native copper very large. Unfortunately, except in the fissure veins, known as " mass-mines," the copper is so scattered through the rock, and is in such a fine state of division, that, although it is not always difficult to mine, it is always difficult to dress it sufficiently to make it pay. The metal is so unifornily distributed throngh these copper-bearing rocks that detached pieces, called " float," are found in digging on almost any land in the country. These pieces vary from very small fragments, weighing not more than a few ounces, up to many pounds. In one instance, in making an excavation for a cellar of a

Jan 1, 1879

By A. Yoshikawa, T. Sugeno

To detenmine the origin of the sharp fatigue limit in many ferrous metals, S-N curvces were determined in push-pull fatigue at 18.6 kc per sec at room temperature and - 67°C for various kinds of iron. These differed in carbon and nitrogen content and grain size (25 and 2500 grains per sq mm). Sharp knees appeared in the S-N curves of fine-grained specimens with high interstitial content at both temperatures. In coarse-gruined specimens, knees were not sharp .regardless of the interstitial content and the testing temperature. It is concluded from these results that the controlling factov for the appeavance of the sharp fatigue limit is not strain aging but grain size. It has already been mentioned that iron and some iron alloys show fatigue curves characterized by a more or less sharp knee and a fatigue limit.' Explanations of the origin of this characteristic behavior of fatigue in iron appear to fall into two broad classes. One is concerned with interstitial impurities through the aging or locking effect and the other is based on intrinsic plastic properties of iron. Levy and sinclair2 and Lipsit and Horne3 have suggested that the fatigue limit observed generally in iron and steel is due to interstitial solute aging during the course of fatigue. On the other hand, Thompson and wadsworthl have suggested that the fatigue limit may be analogous to the sharp yield point, in the sense that alternating stresses above the fatigue limit are necessary to break down the dislocation locking. However, there are some experimental results which cast doubt on the general validity of these suppositions.4-8 Ferro and Montalenti' have recently suggested that the typical form of the fatigue curve of iron seems to come from an intrinsic plastic characteristic of the iron structure. This suggestion is based on the experimental result that pure iron containing an insufficient amount of interstitial solute to alldw appreciable strain-aging effects still showed a fatigue limit at room temperature. Although systematic investigations on the effect of grain size are scarce, it is thought that this effect is important in relation to the sharp fatigue limit. In fact, sensible differences were observed by Oates and Wilson4 in fatigue behaviors of a low-carbon steel depending on grain size. Ideally, the fatigue limit will be defined as the upper limit of stress amplitudes at which the life is infinite. This ideal fatigue limit can never be determined because of the limited time available for experiments, and moreover scattered data points often leave the construction of S-N curves somewhat arbitrary. And, it is usually stated that a material has a fatigue limit when its statistical S-N curve becomes apparently parallel to the N axis with a more or less sharp knee. The meaning of the fatigue limit and the sharp knee will be discussed in detail in relation to the construction of S-N curves. The origin of this sharp knee was investigated by determining S-N curves of iron for various interstitial contents, testing temperatures, and grain sizes. EXPERTMENTAL PROCEDURE The material as received was a commercial-grade low-carbon steel in the form of 4-mm-diameter rods with the following composition in weight percent: C, 0.09; Si, 0.017; Mn, 0.43; P, 0.006; S, 0.012; Cu, 0.11. Five different groups of specimens were tested. The grain sizes and interstitial contents in each group are given in Table I. The specimens of group C-02 were decarburized by annealing for 100 hr at 700°C, followed by an additional 100 hr at 850°C in wet hydrogen. Specimens of groups N-2 and N-9 nitrided in a mixed atmosphere of ammonia and hydrogen after an initial treatment identical to group C-02. The specimens of group C-9 were prepared in a manner similar to those of group C-02, except heat treatment was carried out in a vacuum. After polishing their surface with emery paper, the specimens of all groups were given a final anneal for 30 min at 930°C and air-cooled in an evacuated quartz tube. For group C*-9 this

Jan 1, 1965

By Thomas V. Falkie

The three basic ingredients of fertilizers are nitrogen, phosphorus, and potassium. Nitrogen comes from natural gas or other sources and is usually a "manufactured" ingredient. Phosphorus and potassium come from mineral sources which are mined in open pit and underground mines all over the world. Phosphorus is one of the 15 chemical elements needed to sustain life. Along with nitrogen and potassium, it is essential to the fertility of the soil and to the growth of plant life. Plants require phosphorus for proper soil conditions, early root formation, and crop maturity. Humans and animals require phosphorus for bone and tooth development. The primary raw material for phosphorous fertilizers is phosphate rock. It is found and mined in many areas of the world. Morocco, the United States, USSR, Tunisia, and some Pacific Islands are the leading rock producers. Other sources of phosphate are guano, bone meal, and other natural organics, but these comprise a very small percentage of all phosphate used. Phosphate rock in the United States is mined in Florida, North Carolina, Tennessee, Idaho, and Montana. Florida alone produces about 70% of all the rock mined in this country, mostly from a 20 X 30 mile area in Polk and Hillsborough Counties in central Florida known as the Bone Valley district. There are phosphate reserves in many parts of Florida, and within the past three years mining has begun in north Florida in Hamilton Country (see Fig. 1). In 1967, world phosphate rock production was about 75 million short tons (st). The United States produced about 35 million st (about 47%) of which Florida produced about 25 million st (about one-third of world production). According to Phosphorus and Potassium magazine (Mar./

Jan 1, 1969

By Gram Curtis

The apparatus described below for the handling of plates upon their delivery from the rolls, embodies features believed to be of interest to those contemplating the building of new plate-mills, and also to such owners of existing mills as may be considering the improvement of their works. The points to which attention is called are the small space required for the finishing-end of the mill, and consequently the very moderate size of the building for the amount of plates handled; the directness and ease of manipulation, and therefore the mall amount of labor required; the distribution of plates; the facilities and time allowed for their cooling. These, together with other features of detail and general arrangement scarcely less important, will become apparent when the descriptions and illustrations herewith given are understood. As these devices deal with the finishing of the plates only, they may be added to any plate-train when the floor-space and the building are large enough to permit their introduction; and it will be obvious that the features of this method, more or less modified, are applicable to any existing mill. Figs. 1 and 2 show a three-high 32-and 19- by 120-inch Lauth mill, with hydraulic lifting-tables, served by four heating-furnaces, with hydraulic cranes for charging and drawing. Upon leaving the rolls, the plate is allowed to rest with its forward edge projecting somewhat beyond the end of the catcher's table. Here it is seized by the automatic tongs, A, suspended from a buggy travelling in the overhead trough, B, and actuated by the hydraulic cylinder, C. These tongs are operated by a boy, who stands several feet from the heated plate, and controls the long light handle, D, shown in the plan, Fig. I. His duty is merely to advance the tongs by means of .the hydrulic cylinder, C, to raise or

Jan 1, 1892

By J. E. Campbell, G. D. Calkins, N. M. Ewbank, M. Pobereskin, A. Wesner

GRINDING for size reduction affects the economics of many processes and products. It is essential as the first step in many industrial processes and is also a finishing step for materials with properties depending on particle size, such as talc, cement, and silica sand. Intermediate and fine grinding are vital operations in the U. S. cement industry, which is producing more than 250 million bbl of cement per year.1 Wear of the grinding media is a large part of the grinding operation cost. Problems encountered in grinding cement are so complex that evaluation of efficiency and economy of grinding media is difficult.2 It has been especially difficult to evaluate the relative effectiveness of different types of balls because there are no good testing techniques.

Jan 12, 1957

Discussion of the paper of Archer E. Wheeler and Milo W. Krejci, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1831 to 1880. BRADLEY STOUGHTON, New York, N. Y.:-I would like to ask Mr. Krejci whether they have tried mixing coke dust with the lime in those converters and, if so, if any advantage has been found. It has been a very great advantage in the steel converters where coke dust has been mixed with the lime near the tuyeres. Of course the agent that causes the corrosion at that point is oxide of iron, and coke seems to prevent the formation of the oxide of iron and so protect the tuyeres. It would be interesting to know if it had the same effect in the copper converters. MILO W. KREJCI:-We have never tried it here. At Anaconda the tuyere section was formerly put in by mixing magnesite with tar and ramming that into the tuyere section, but they have abandoned that. Might I ask how you would apply the coke dust? How get it into the tuyere section ? How hold it there ? BRADLEY STOUGHTON :-The coke dust is mixed with silica and clay and then rammed in and burned. I suppose in your converters it would be mixed with the magnetite or magnesite and then agglomerated with the material in place. MILO W. KREJCI:-We never tried it here. PROF. JOSEPH W. RICHARDS, South Bethlehem, Pa.:-I would like to ask how thick this deposit of magnetite is on the lining. How thick a layer would be practical ? MILO W. KREJCI:-About 21 in. would be sufficient. SOLOMON LE FEVRE, Mineville, N. Y.:-I was interested to hear of the use of magnetite in connection with the copper smelter. I am interested in the mining of magnetite, but was not aware that it had been used at all' by the copper metallurgists.

Jan 11, 1913

By R. A. Mosser

Production control of aluminum content of low carbon aluminum killed open hearth steels is being achieved by using an oxygen probe unit. Based on the free oxygen content of the bath after block, a preliminary chart for aluminum additions has been established. The aluminum aim is .040%. Controlled aluminum contents will result in eliminating coarse grain heats, high aluminum contents, and a reduction in aluminum costs. By reducing the frequency of high aluminum contents both cleaner and better rolling heats will be obtained. The savings in aluminum costs is an added benefit of lesser importance in comparison to the quality improvements gained by controlled aluminum contents. Although the main goal for the oxygen probe at Republic Steel has been to adapt it for production control of aluminum contents, future usage could be extensive. Immediate plans for using the probe are on degassed material, on fully blocked open hearth heats to improve manganese recoveries and ranges, and on machining grades to control oxygen content. Also by controlling the oxygen content of the steel to as close to equilibrium conditions as possible, cleaner steel will result.

Jan 1, 1972

By R. J. De Angelis, J. B. Cohen, A. Nelson

In this note several recent results on twinning in copper shock-loaded with planar shock waves will be presented and the role of the twins in recrystalliza-tion will be discussed. The twinlike markings first observed in shock-loaded copper by smith1 were identified as twins by De Angelis and Cohen.2 This identification has been confirmed by others.3 In Ref. 2 it was also shown that there is an orientation dependence for twinning at low shock pressures, such that twins in a crystal loaded in [lll] form in the rarefaction or tensile wave but in

Jan 1, 1967

By V. Patarini, D. Kuehl, F. Galasso, M. Salkind

In recent years, a great deal of research has been directed toward the production of continuous low-density, high-strength, high-modulus boron fibers for aerospace applications. A technique which has proven to be quite successful for forming these fibers involves the reaction of boron trichloride and hydrogen on a hot tungsten wire. In this process, a boron fiber is produced which consists of a tungsten boride core covered with amorphous or crystalline boron depending on the temperature of the preparation.2,3 The purpose of this paper is to present the properties which have been obtained to date from measurements and observations on these fibers. Selected samples of boron filament produced by reacting boron trichloride and hydrogen on a 0.5 by 10-3 in. diam tungsten wire substrate using different reacting temperatures were cross-sectioned, polished, and photomicrographed with cross-polarized light. The temperature of the wire was measured using a two-color optical pyrometer. Photomicrographs of these samples are shown in Fig. 1. Three general types of boron, in addition to the tungsten borides, have been identified by means of X-ray powder diffraction techniques: a) at low temperatures (below 1400°C) the boron is deposited in the amorphous form; b) at temperatures between 1400° and 1500°C the boron is deposited in the ß tetragonal form; and, c) above 1500°C the boron is deposited in the B rhom-bohedral form. In the depositing range of 1400" to 1500°C the boron initially deposits as amorphous and becomes crystalline as evidenced by the large equi-axed grains which then merge into columnar grains in later stages of boron deposition. This can be seen in Fig. 1 and has been observed in the X-ray patterns of these fibers, which contain both halos from the amorphous boron and lines from the ß tetragonal form. Above 1500°C the only boron reflections observed in the X-ray patterns were those of the ß rhombohedral form and only columnar grains are seen in the photomicrographs. Photomicrographs of the surface in Fig. 2 show the smooth-surface kernal-type deposition which corresponds to the amorphous form and the rougher surfaces which correspond to the crystalline form. Mechanical measurements were made on amorphous boron produced at 1300°C rather than the crystalline boron because the strengths of these filaments were greater and were more consistent. A tensile tester consisting of a fixed crosshead containing a double

Jan 1, 1967

By Waldemar Lindgren

CONTENTS. [ ] THE following pages are a resun16 of some of the conclusions reached during a study of the copper-deposits near Clifton The field-work was finished in 1902 and a complete report is now in the press. A preliminary description of the district was published in 1903, in Bulletin U. S. Geological Survey, No. 213. pp. 133-140

Jan 1, 1913

By Y. Nakada, B. Chalmers

The work-hardening behavior of surface layers of aluminum and gold single crystals was investigated by alternately deforming and then removing a thin surface layer by electropolishing or by etching. Aluminum crystals exhibited lower flow stresses after the surface removal; gold crystals did not. Abrasion of surface eliminated easy glide in both gold and aluminum crystals. By alternately deforming and removing the surface layer, it was shown that the abraded crystals work-harden preferentially under the abraded layer. It is suggested that this phenomenon is caused by the difficulty of propagating dislocations through the abraded layer. It has been demonstrated in numerous cases'-3 that the plastic behavior of metals in either single-crystal or polycrystal form is sensitive to the environment and to the condition of the surface; it has also been reported4-6 that single crystals of some metals, when deformed in tension, exhibit more work hardening near the surface than in the interior. A third type of effect that has been attributed to the special part played by the surface in plastic deformation is the influence of the dimensions of the specimen on the various parameters that define its plastic-deformation characteris- tics.?-'' Many of these experiments were made on aluminum, on which an oxide film is always present under available experimental conditions; many of the effects have been attributed to the oxide film, either in terms of its higher elastic moduli, which would cause local stress redistribution, or its higher strength, which would oppose the escape of dislocations at the surface of the metal. On the other hand, it has been suggested II,12 that the mere presence of a surface should be sufficient to produce the observed results. A rigorous examination of this question could, in principle, be carried out by comparing the behavior of aluminum with its oxide film with that of the same material without oxide. This experiment would present great difficulties. The most practical alternative is to compare aluminum with gold, which has no crystalline surface film at room temperature, and to study the effects of various surface treatments on gold. The experiments described in this paper fall into two groups, the objectives of which were to determine 1) whether single crystals of gold shared the property of aluminum that the removal of a surface layer after some plastic deformation reduced the flow stress for further deformation and, since the result of this was negative, 2) whether a surface treatment could be found that caused gold to behave in this way. I) EXPERIMENTS AND RESULTS All the tests described below were carried out on single crystals of about 6 by 6 mm cross section and of sufficient length to provide a gage length of about 10 cm.

Jan 1, 1964

By D. W. Fuerstenau

Recently R. J. Charles1 showed that comminution of brittle or semi-brittle materials in batch operations is described more appropriately by a variable energy relationship than by the specific relation- ships proposed by Rittinger,2 Kick,3 and Bond.4 That is, the value of n in the empirical differential operation which applies to crushing and grinding (Eq. 1) is variable. Independently, Holmes6 developed an identical generalized equaton for size reduction. The experimental data of Charles and Holmes show that the value of n is determined by the material and the comminuting machine and is constant for a given combination of these two conditions. The general objective of the present article is to extend the Charles-Holmes concepts to continuous ball milling. The specific objective is to analyze the operation of a vibratory ball mill dry-grinding chromite in a continuous open circuit and to develop an equation for the comminution of chromite in this mill.

Jan 12, 1959

By Charles E. Glass

The stabil ity of engineered embankments subjected to earthquakes has received considerable attention in the last 10 years, but most of the effort has been directed toward stability of earth dams. Based upon past performance, earthquake- induced failures on non-impounding mine waste structures will likely correspond to small, local slumps or debris slides, and their stability should be considered as an integral part of mine economic planning. As such, stability considerations should include earthquake hazard, characteristics of earthquake ground motion, dynamic slope stability, and the impact that waste-dump failures have on mine operations. Numerous techniques have been proposed for analyzing the stability of embankments subjected to earthquakes. Before choosing an analysis technique, it is worth noting two important differences between the dynamic response of waste embankments and natural slopes. First, waste embankments respond as structures having unique modes of vibration, which causes embankment motions to differ from nearby ground motion. Second, because of embankment response, accelerations can be different at embankment crests than elsewhere in the structure and occur at frequencies that do not correspond to input ground motion. Because of these factors, embankment response should be calculated prior to slope stability assessment. In this paper several analysis techniques designed to calculate slope stability are evaluated, and conventional pseudostatic techniques are shown to be inappropriate for dynamic considerations. Techniques to calculate dynamic stability should include embankment response, all characteristics of earthquake motion, and roughness along failure planes as input, and should provide a displacement time-history of the slide mass as output. Two techniques satisfy this criterion, and in this paper the LADRS technique is recommended for its versatility and simplicity.

Jan 1, 1985

INDUSTRIAL MINERALS DIVISION (Nonmetallics) Established as a Division March 15, 1935 Ian Campbell, Chairman Robert C Stephenson, Eastern Vice-Chairman Allen Cole, Southeastern Vice-Chairman David P Hale, Jr, Rocky Mountain Vice-Chairman G H Waterman, Western Vice-Chairman M F Goudge, Canadian Vice-Chairman James Norton, Secretary-Treasurer Mineral Deposits Branch U S Geological Survey Washington 25, D C.

Jan 1, 1952

By Basil Prescott

In the science of evolution of the species, there is a law which, simply stated, avers that the history of the individual repeats the history of the race. Similarly, if unassisted by the experience of others, each SUCcessful engineer would perfect and develop his methods and technique from the rough grab sample up to the carefully taken, recorded and studied samples and observations which now determine and decide the expenditure of the large sums required for modern mining. Hence real progress results from the interchange of experience, as in that way the entire experience of the profession can be made available to every engineer. The literature of this subject is already voluminous, but some progress has been made in the gathering of data and in their compilation or presentation. More Romance than Developed Ore in Limestone Deposits In certain types of deposits, methods little known 25 yews ago have been developed, perfected and standardized to a degree that lifts sampling from the field of manual labor to the plane of an applied science; for instance, the modern methods of estimating the so-called porphyry coppers. With some types of orebodies, we have become familiar, and sometimes on too easy speaking terms, with millions of tons of ore in reserve and tens of millions of dollars; while with others even these once marvelous figures sink into insignificance before the array of ciphers that are presented. .In such company, the average limestone replacement orebody is entirely out of place, for its reserves seldom reach a figure to arrest the attention of the modern engineer, and more often are insignificant. It is only when the records of the production of some of the older camps are studied, which show them to have continuously produced over very extended periods, that a realization is borne home that occasionally this type is worthy of consideration even in these days of gigantic tonnage.

Jan 1, 1925

By S. Floreen

Seven iron alloys ranging from 5 to 12 pct Ni and 5 to 14 pct Cr were studied. All alloys transformed to bcc massive martensites. Tempering increased the strengths , probably because of relief of residual stresses generated by the martensite transformation. The major strengthening mechanism appeared to be solid-solution hardening by nickel and chromium. Studies of the work-hardening behaviw, of the effects of prior austenite grain size, and of the effects of changing strain rate and test temperature gaue results very similar to iron or low-alloy steels. Increasing nickel contents markedly improved the toughness at subzero temperatures. Studies of the flow properties did not, however, indicate the reason for the beneficial effect of nickel on toughness. The marine atmosphere corrosion resistance of the alloys was improved primarily by chromium additions, but increasing nickel contents were also beneficial at low levels of chromium. J\ number of maraging and PH stainless steels are strengthened by precipitation hardening in a low-carbon Fe-Ni-Cr martensite matrix. To some extent the resultant properties of these steels must depend upon the properties of this matrix. The present study therefore was conducted to evaluate the transformation characteristics and mechanical properties of a series of Fe-Ni-Cr martensitic ternary alloys. A limited evaluation of the corrosion resistance of the alloys in marine atmosphere was also made. ALLOY PREPARATION Seven 100-lb air induction melts were prepared using electrolytic iron, nickel, and chromium metal additions. The initial Fe-Ni charge also contained 0.05 wt pct graphite to produce a carbon boil during melt down. After melting of the base charge, the heats were refined with 0.1 wt pct additions of manganese, silicon, aluminum and titanium and poured into cast-iron molds. The ingots were homogenized at 1250°C and uni-directionally hot-rolled to 2-in. plate. They were then homogenized another hour at 1250°C, and unidirection-ally hot-rolled to %-in. plate at a finishing temperature of approximately 1050°C. The compositions of the heats are given in Table I. Two additional heats were prepared as 40-lb vacuum-induction melts using electrolytic iron, nickel, and chromium metals, and commercially pure molybdenum chips. A carbon boil, and 0.1 wt pct additions of aluminum and titanium were again employed, but manganese and silicon were not added. The heats were converted to %-in. plate using the procedure described above. The compositions of these heats are included in Table I.

Jan 1, 1967