Search Documents

By James W. Malcomson

The Tigre Mining Co. of Mexico, owned by the Lucky Tiger Combination Gold Mining Co. of Kansas City, decided early in 1910 to enlarge its mill, which consisted of a concentrator milling 3,000 tons of ore per month. The enlarged plant was designed to crush and concentrate 6,000 of ore and to cyanide 7,500 tons per month. The extra tonnage cyanided was to be obtained from tailings which were stored below the old mill. Power was supplied to the old mill from four boilers; a 150-h-p. Corliss engine and two Weber 60-h-p. gas-engines using producer-gas made from charcoal. The total horse-power required, including 60 h-p. used for machine-drills in the mine, was approximately 275. Cord-wood cost $4.32 per cord, 8 by 4 by 3 ft., and charcoal $15 per ton. The fuel supply in the surrounding country was approaching exhaustion; more than 150 mules and 50 men were engaged in cutting and transporting this fuel, and the unsettled political conditions in Sonora were such that it would be practically impossible to keep an organization of this kind together. The price of fuel was steadily rising and at times it became almost impossible to get sufficient fuel to operate. It was estimated that the enlarged plant, together with the mine, would require 750 h-p., as follows: Horse-Power. Old mill, which was left unchanged,..............180 New concentrator,.......................90 Cyanide-plant,........................380 Mine and other requirements,................. 100 Total,........•..................750 In a study of the best manner to obtain power the following alternative propositions were considered:

Jan 1, 1914

By Karl L. Fetters

In the process of making steel in the open-hearth furnace the refining of the metal during the working period of the heat is largely accomplished through the agency of the slag. From the birth of the process until the present day steelmakers have recognized the importance of the slag in determining the composition of the metal and the quality of the product. The general relationships between slag composition and metal analysis have long been known, at least in a qualitative or approximate fashion. For examples, the iron oxide content of the slag is higher on lower carbon heats; the more basic slags are higher in iron oxide for a given carbon content; certain amounts of iron oxide and lime arc required for phosphorus removal and a high lime-silica ratio is needed if the sulphur content of the metal is to be diminished. In recent years a number of quantitative relationships involving these and other variables have been developed through plant and laboratory studies by numerous investigators in this country and abroad. The direct comparison of laboratory and open-hearth data involves the question of the degree to which each approaches the conditions of chemical equilibrium, a question which, from the open-hearth standpoint, we are scarcely yet in position to answer. And, although a considerable body of dependable equilibrium data has been obtained in the laboratory, this work has not yet been extended to cover the ranges of slag composition encountered in basic open-hearth practice. In the present study we shall not attempt to draw comparisons between data from the two sources; nor do we attempt to draw conclusions as to the approach to chemical equilibrium in the open-hearth furnace. Many of the operating variables that are likely to be erratic or unrecorded during the earlier stages of the heat become more consistent and arc more readily subject to observation and control during later stages. For example, undigested lime or ore gradually goes into solution, the rate of carbon drop levels off, and the temperature of the metal is brought under control. For these and other reasons a greater degree of self-consistency is likely to be found among data obtained during the

Jan 1, 1940

By Karl L. Fetters

In the process of making steel in the open-hearth furnace the refining of the metal during the working period of the heat is largely accomplished through the agency of the slag. From the birth of the process until the present day steelmakers have recognized the importance of the slag in determining the composition of the metal and the quality of the product. The general relationships between slag composition and metal analysis have long been known, at least in a qualitative or approximate fashion. For examples, the iron oxide content of the slag is higher on lower carbon heats; the more basic slags are higher in iron oxide for a given carbon content; certain amounts of iron oxide and lime arc required for phosphorus removal and a high lime-silica ratio is needed if the sulphur content of the metal is to be diminished. In recent years a number of quantitative relationships involving these and other variables have been developed through plant and laboratory studies by numerous investigators in this country and abroad. The direct comparison of laboratory and open-hearth data involves the question of the degree to which each approaches the conditions of chemical equilibrium, a question which, from the open-hearth standpoint, we are scarcely yet in position to answer. And, although a considerable body of dependable equilibrium data has been obtained in the laboratory, this work has not yet been extended to cover the ranges of slag composition encountered in basic open-hearth practice. In the present study we shall not attempt to draw comparisons between data from the two sources; nor do we attempt to draw conclusions as to the approach to chemical equilibrium in the open-hearth furnace. Many of the operating variables that are likely to be erratic or unrecorded during the earlier stages of the heat become more consistent and arc more readily subject to observation and control during later stages. For example, undigested lime or ore gradually goes into solution, the rate of carbon drop levels off, and the temperature of the metal is brought under control. For these and other reasons a greater degree of self-consistency is likely to be found among data obtained during the

Jan 1, 1940

By M. E. Wadsworth, J. S. Cho

The kinetics of silicate adsorption from aqueous colloidal (SO2 . nH2O) silicate sols on thoria (ThO 2) surfaces were determined at 100, 150 and 200°C in an autoclave system. The amount of chemisorbed silica on the thoria surface was determined by means of infrared spectroscopy. First order kinetics were observed in all cases with the anomalous result that the first order rate constant was found to vary with the initial amount of silica added to the system. These results have been correlated quantitatively by means of a strain model of adsorption involving two types of surface silicate bonding, both of which may be readily observed in the infrared spectrum. Initial adsorption occurs rapidly to produce one type of surface silicate followed by a slow transition to a second type of surface bonding, the latter transition representing the slow step in the adsorption process. Initial interest in silicate adsorption on thoria arose from the dispersive effect silica has on finely divided thoria in aqueous suspensions. Spaepen et al studied the equilibrium adsorption of silica on thoria and noted increased adsorption up to approximately 215°C with a notable decrease in adsorption at temperatures above 215°C. Similar results were observed by Cho and Wadsworth2 who identified two types of surface silica by infrared spectroscopy. At temperatures of 100°C and above, rapid initial adsorption occurred producing a surface species with maximum infrared absorbance at 9.4 After extended periods of time, the 9.4 species converted to a more strongly bonded surface silicate with maximum infrared absorbance at 10.3. The latter was very strongly bonded and difficult to remove by desorption in hot distilled water, while the 9.4 species could be removed more readily by similar treatment. The 9.4 and 10.3-p species were distinguishable from free unadsorbed silica which had maximum infrared absorbance at 9.1 The kinetics of the formation of the strongly chemisorbed silica (10.3) on thoria as determined by infrared examination are presented in this study. EXPERIMENTAL PROCEDURE As a source of silicate, Ludox SM (16.36% SiO2) or Ludox HS (30.25% SO2), DU Pont colloidal silica in aqueous suspensions, was added directly to a thoria slurry made up of one liter of distilled water and one gram of thoria. The thoria used was designated D-16-650 and was received from the Chemical Technology Div. of Union Carbide Nuclear Co. It was prepared by firing thorium oxalate at 650°C. The D-16 thoria had a surface area of 32.4 ± 0.6 sq m per g as determined by nitrogen adsorption.* This thoria 'Determined by Unlon Carbide Nuclear Co., ORNL. had a total adsorption capacity for silicate of approximately 19.4 mg of silica per gram of thoria.1 This amounts to approximately one SiO2 molecule for every surface thoria site. In all cases in this study.

Jan 1, 1963

By R. C. Hepworth

Heaving in roads built on the Mancos Shale is a serious problem in east-central Utah. Heaves are expressed as local bumps, general rises and severe cracking of the pavement. The heaves usually occur in shale road cuts and generally show a seasonal cycle, which reaches a maximum development in the winter. The presence of certain salts, absorption of moisture and physical properties of the subgrade materials were considered, in Utah, to be the main factors in the heaving mechanism. Work done on similar problems elsewhere and studies conducted by the author indicate that the latter two factors are the most important. Results of this investigation indicate that heaving areas are associated with slaking shale or expansive clays, with and without salts present. Laboratory studies show that the initial moisture content of remolded samples and the desiccation history of un- disturbed samples have a major effect on swelling. Swell tests on compacted samples at various temperatures indicate that water has more influence on swell than temperature, except for samples containing sodium sulphate, which swelled with decreasing temperature. Chloride salts inhibited swelling. Tests on shale cores indicate that the stability of slaking shale can be preserved by maintaining its original moisture content. It is concluded that shales and expansive clays, when exposed in road cuts, become desiccated and are subject to expansion when moisture is subsequently available. The seasonal cycle of heaving may possibly be explained by the annual moisture excess and deficiency. To minimize the problem, freshly exposed shale should be kept wet, and the thickness of the subbase and base courses should be increased. The Utah State Department of Highways has been plagued for many years with a distressed condition that develops in roads constructed on the Mancos Shale. Locally these distressed areas are known as heaves, frost boils and alkali boils. These names refer to the surface expression, time of year

Jan 1, 1965

By Dr. O’Neil Thomas J., Donald W. Gentry

"We can easily represent things as we wish them to be..” -Aesop INTRODUCTION The first eight chapters of this book have primarily addressed the concepts and fundamentals associated with project valuation, particularly as they apply to mining-related projects. Specific emphasis was placed on the engineering and economic parameters and estimates necessary for quantifying line items in pro forma income statements and the subsequent calculation of net annual cash flows. Given these estimates of relative benefits, costs, and annual cash flows for a project, it then becomes necessary to convert these estimates into measures of relative desirability or attractiveness. The criteria and techniques typically utilized to determine project acceptability or desirability are, then, the topics of discussion in this chapter. Before proceeding it may be advantageous to put the problem of project evaluation into proper perspective by reiterating some of the fundamental concepts developed in Chapter 1. The basic premise set forth in this book is that the objective of the firm should be to maximize its value to its owners (stockholders' wealth). This value or wealth is represented by the market price of the firm's common stock; consequently, the primary objective of the firm can be restated as one of maximizing the value (price) of the firm's common stock in the marketplace over the long term. This price, in effect, is an indicator or index of the market's perception of the company's progress and a reflection of the investment, financing, and dividend decisions made by corporate management. These three major decisions are inter- related and jointly impact the market price of the firm's stock. Therefore, if the objective of maximizing the value of the firm to its stockholders is to be achieved, an optimal combination of the three decisions will be necessary. It is important to emphasize that maximizing stockholder wealth is not the same as profit maximization or even the maximization of earnings per share. Corporate managers making decisions based on the objectives of maximizing profits and/or earnings per share must recognize that these objectives do not consider: (I) the timing or duration of expected returns, (2) the business and financial risks of the promised earnings, or (3) the dividend policy of the firm. Obviously all of these factors are of concern to the company's stockholders and will have an effect on the market value or price of the firm's common stock. Maximizing market price per share, or wealth maximization, is therefore the appropriate corporate objective and

Jan 1, 1984

W. P. Blake, Shullsburg, Wis.: I desire to express my admiration of Prof. Posepny's memoir, and particularly of the charming manner and spirit of the introduction. With respect to his mention of the ore-deposits of Missouri and Wisconsin, reference may be made to my paper presented at this meeting (Trans., xxii., 621)) showing the existence of dislocations and breaks in the bedding, and their apparent close relation with the localization of the ore-deposits as claimed by Dr. James G. Percival, and also so claimed by Dr. Jenney in his paper before us (Trans., xxii., 171). I have in my paper given reasons for believing that the zinc- and lead-ores in the strata above the compact Trenton limestones were formed by lateral secretion and concentration from above downwards, substantially as shown by Prof. J. D. Whitney, and not by the ascent of solutions through the fissures, as Prof. Posepny (p. 304) seems inclined to believe. In regard to the contemporaneity of the ore and the rocks, and in favor of a later introduction of ore through fault-fissures, Prof. Posepny (p. 310) cites the influence of these fissures. In my paper, already referred to, I have endeavored to show how faults may have influenced the deposition of ore without being themselves channels for the flow of mineral solutions, and how they may have caused the contemporaneous formation of metallic sulphides from sea-water in the body of a forming rock; the faulting fissure being formed at an early period in the foundation rocks, and probably continuing to be a plane of break and movement in the deposits of later formation.

Jan 1, 1894

By Shosei Serata

Stress control methods of mining have been developed separately in at least four different parts of the world in entirely different types of mining -- coal, trona, salt and potash -- during the decade of the 1960s. They all utilized yield pillars as tools for ground control. Today, yield pillars are becoming widely used in under- ground mines in a variety of geological conditions. Stress control methods are effective in stabilizing openings in weak, complex grounds, especially at greater depths. Their advantage is that they utilize existing ground media to stabilize mine openings by altering the stress distribution patterns around the openings, by controlling design parameters such as room width, pillar geometry, and excavation sequence, rather than by using a conventional means of artificial ground support such as roof bolts, cribbing, or arches. Stress control methods, therefore, are suitable for both advance and retreat mining, including total extraction mining. Adaptation of these methods results in substantially greater safety, productivity, and ecnomy over conventional methods. These methods are based on scrutiny of the actual stress conditions in the ground, by both in-situ measurement and computer simulation. This paper provides a summary of stress control methods as developed over the last ten years. The field examples are limited largely to salt and potash mining applications, although the method has been used successfully in other mining applications. The examples illustrate that stress control methods actually address general ground weakness problems -- separation at discontinuity planes, swelling by shale expansion, deterioration by brittle fracture, and interference by ground water. That is, although the principle is developed mainly with reference to salt and potash applications, it is generally applicable to weak ground.

Jan 1, 1983

Edgar Hall, Tenterfield, New South Wales (communication to the Secretary): Mr. Klepetko* asks for information showing at what percentage antimony and arsenic, as impurities, begin to affect injuriously the quality of brass.

Jan 1, 1899

On Friday, Jan. 17, the thirteenth impression of the Perkin Medal was presented to Dr. Frederick Gardner Cottrell, at a meeting of the New York Section of the Society of Chemical Industry, held at the Chemists' Club, in New York City. The presentation address was delivered by Dr. C. F. Chandler, Senior Past President of the Society. The medal was awarded for the recipient's work in the electrical precipitation of suspended particles in gases. Dr. Cottrell's career, which is so familiar to members of the Institute, was sketched by Dr. Chandler. He told at some length of the experiments leading up to the final solution of electrostatic precipitation, which has done so much to solve the problem of smelter smoke. The principal interest in Dr. Cottrell's speech of acceptance lay in his remarks about helium, the production of which has been so reduced in cost that it has practically supplanted the use of hydrogen for inflation purposes in war balloons. He said: "Two or three weeks after war was declared in 1917, Dr. R. B. Moore attended a meeting of the American Chemical Society in Kansas City. At the general session, Mr. Seibel of the University of Kansas, gave a paper on krypton and xenon in some of the natural gases of Kansas. At the end of his paper, he expressed regret that at such a time, when everyone was thinking of war problems, his paper was of a purely scientific nature and had no practical bearing on the war. Dr. Moore immediately got up and said that he did not agree with Mr. Seibel. The presence of helium in those wells could, and should, have a very practical bearing on the war, as this gas could be extracted in quantity from the natural gas and used for balloons and Zeppelins. He pointed out some of the natural advantages of helium over hydrogen, and quoted Sir William Ramsey's letter advocating the use of helium for airships. The general attitude of those present was one of scepticism, so he finally asked Dr. Cady for his opinion who stated that he believed-the thing could be done, but was very doubtful whether it could ever be made practical on account of the cost." Dr. Moore in a letter wrote: "That same day I talked to Dr. Parsons, who was present at the meeting and was returning to Washington almost immediately. I told him what had happened, and that I believed the matter should be taken up by the Bureau at once and presented to the War Department. He promised to do this as soon as he got to Washington; and I know that he did take the matter up with other Bureau officials." Dr. Cottrell continued in part: News of Ramsey's suggestions also reached this .country through other channels and eventually came to our attention. Professors Satterly and Patterson of the University of Toronto commenced experimentation of the subject Jan. 1, 1916. Col. G. A. Burrell, who headed the research department of the Gas Warfare Service at the American University, tells me that Cady's experiments had also suggested similar possibilities to him.

Jan 3, 1919

By A. H. Cottrel

SINCE metallurgy exists to provide strong, tough, engineering materials it must inevitably be perpetually concerned with the problem of brittle-ness. The steel-making industry was created because chemically unrefined iron is brittle. The steel-working and alloy-steel industries exist partly because hardness and ductility are mutually exclusive qualities in structurally unrefined steel. Yet, in spite of these immense industries, the brittle failure of steel ships hulls, bridges, pressure vessels, and pipelines, is still a contemporary problem. In fact, brittleness is a normal property of most solids, including metals and alloys, at low temperatures. Only face-centred cubic metals are commonly ductile at the lowest temperatures, and even here exceptions are known.'," Expensive are-melting processes. under inert gases or vacuum, have been developed to overcome brittleness in titanium, zirconium, columbium. and molybdenum. Polycrystal-line zinc, magnesium, and uranium have little ductility at room temperature. Beryllium, chromium, and tungsten have even less; similarly for antimony, bismuth, germanium, silicon, intermetallic compounds, and metallic carbides, nitrides, silicides, and borides. Oxides and other ceramics would be ideal creep-resistant materials but for their extreme brittleness when cold, and great efforts have been made to overcome this problem by mixing ceramics with metals. In fact, the traditional use of the name metallurgy for what is really the science of engineering materials is a recognition that most non-metallic solids have so far been precluded, by their extreme brittleness, from use as major structural materials in mechanical engineering. Most of what we know about brittleness in metals has come from studies of structural steel, and it is this material that shall mainly be considered. The things we have learned from it have a wider application, at least to other body-centred cubic transition metals, although the extent to which similar ideas can be applied to hexagonal metals and other materials is not yet clear. Fracture and Plastic Deformation The theoretical breaking strength of an ideal solid, about E/10 where E is Young's modulus, has been approached reasonably closely in experiments on fibres. But large specimens break at much lower stresses. For example, brittle cracks in large structural steel assemblies have been observed to spread catastrophically at speeds of 6000 ft per sec under stresses of about 10,000 psi, i.e. about E/3000. There are two sources of weakness; stress concentrations, and chemical agents in grain boundaries or on crack faces that lower the surface energy y of the material. Although we shall deal mainly only with the first of these, much of the discussion is also applicable to the second when different values of y are used. Griffith's well-known formula p = [ 2Ey/p(1 - v2)c]1/2 [1] gives the smallest tensile stress p able to propagate an atomically sharp surface crack of length c or interior crack of length 2c through a thick plate (compared with c) of elastically isotropic material of

Jan 1, 1959

By Homer W. Riley, C S. Jenkins

SMALL power-driven, toothed, cast-iron rolls were used first to break anthracite in 1844. Prior to that time, men with hammers, who stood on perforated cast-iron- plates, .broke the large lumps into commercial sizes. In order to convert run-of-mine into the various sizes required by the anthracite industry, about 20 million tons must be broken, annually, [ ] into smaller sizes. This phase of anthracite preparation is of major importance, because the degradation accompanying reduction in coal sizes should be kept at a minimum. The exclusive use of toothed rolls for that purpose indicates that comminution by rolls is the best solution of the problem. Many improvements have been made in tool design, but the most important was a reduction of the peripheral speed of the rolls from 1000 to 300 ft. per minute. The higher speed was based upon and approximated the velocity of a falling piece of coal when it entered the rolls. Exhaustive roll tests at the slower speed showed that the same size reduction could be affected with less degradation. The adoption, there- fore, of slow-speed, compound geared rolls, especially for breaking the

Jan 1, 1943

By E. W. Wagy

The year 1927 witnessed numerous developments of significance in California. The State's shut-in production increased from an average of 58,000 bbl. daily in January to a maximum of 93,000 bbl. daily in August, and a total of about 25,000,000 bbl. was withheld from the market during the year. This not only lessened the effect of large production at Hunt-ington Beach, Seal Beach and Alamitos Heights, but also was a most effective conservation move. Since 1922, it is estimated that approximately 100,000,000 bbl. of oil that would otherwise have been produced have been held in the ground. I. Outstanding Field Developments of 19271 1. Long Beach Deep Sand. 2. Rincon (Seac1iff)Discovery. 3. Alamitos Heights Discovery. 4. Ventura Avenue Extension. 5. Round Mountain Discovery. 6. Mt. Poso Extension. 7. Potrero (Cypress) Discovery. 8. Buttonwillow Gas Development. 9. Goleta Discovery. 10. Union Avenue, Edison and Fruitvale Areas. (See Fig. 1.) II. Crude Production The most important factor in new crude production in 1927 was the Seal Reach field with its adjacent Alamitos Heights townlot area. Production increased from about 10,000 bbl. daily in January, to a peak of 66,000 bbl. in June. Huntington Beach finished the year 1926 with a production of 102,000 bbl. daily, which declined to 60,000 bbl. by the end of 1927. Due to production in these three areas and the tempering effect of shutting in numerous wells, the California production curve for 1927 was held at a fairly even level. Fig. 2, shows the State's production in 1927 and 1926 as compared with 1923, which was the year of excessive

Jan 1, 1928

By G. T. Davis, C. C. Mattax, M. O. Denekas

The effects of crude oil cornponents on the wellabil-ities of sandstone and limestone were investigated. Fractions containing cornponents differing in molecular weight and molecular structure were obtained from crude oils by distillation, extration and chromatography. Individual fractions were then tested for their effects on rock wettability. Tests indicate that sundstone wetta-bility may he changed by a complex variety of surfactants varying both in molecular structure and molecular weight. Limestone appears to be particularly sensitive to basic, nitrogenous surfactants. INTRODUCTION Investigations in recent years have shown that petroleum reservoir rock wettability can exert a significant influence on the efficiency with which oil can be produced by water flooding. While most reservoirs are presumably water-wet, they niay range in their degree of water-wettability from near-neutral to strongly water-wet.'" Reservoir wettabilities other than strongly water-wet are likely to be induced by adsorption of surface-active components froni the crude oil on the pore walls of reservoir rock.:' Little is known, however, about the nature of the surface-active materials which are likely to be adsorbed by the reservoir rock. Due to the complexity of crude oils. attempts made in the past90 isolate these surface-active components have met with only limited success. It is probable that many different types of surface-active materials arc indigenous to crude oils and that many of these may be adsorbed to varying degrees by reservoir rock. This was cxolored in the studies discussed in this paper. The over-all objective in these studies is to ascertain whether the wettability of a given reservoir can be determined by examining the surfactant content of the reservoir crude. To this end, crude oils were examined to determine the variability of indigeneous surfactants with regard to chemical type and molecular weight. Crude oils were separated by distillation into fractions differing principally in molecular weight, by chroma-tography into fractions containing compounds differing in polarity, and by solvent extraction into nitrogenous and non-nitrogenous fractions. Individual fractions were then tested for their effects on the wettabilities of sandstone or limestone rock samples. EXPERIMENTAL PROCEDURES Fractionation of the Crude Oils Samples of Miocene, Eocene and Jurassic crudes were distilled at temperatures not exceeding 200°C. The final stages of distillation were completed in a molecular still at pressures down to three microns of mercury. Fifteen to 30 fractions were obtained from each crude oil. These cuts were sufficiently broad that separation can be considered to have been effected principally on the basis of the molecular weights of the constituents of the crude oil. A considerable portion (20 to 40 per cent) of the crudes would not distill under these conditions. The residues were recovered and tested with the other fractions. Fractions differing in polarity were separated from a crude of Pennsylvanian age and an extracted sample of Miocene oil by chromatography, using a solid adsorbent. Since surfactants are, for the most part, polar compounds, chromatography should separate many of the surfactants from the crude oil. Such a separation should provide fractions containing compounds differing in molecular structure. Nitrogeneous compounds were extracted from Miocene crude oil with a solution of sulfuric acid in meth-anol. The residual oil was further processed by chonia-tography. Each of the fractions obtained by thesc procedures was dissolved in a non-polar solvent (xylene) and diluted to its original concentration in the crude oil. No attempt was made to maintain an anaerobic atmosphere above the samples while they were being dissolved. These solutions of the fractions were then tested for their effects on the wettability of sandstone and limcstone as discussed in the next section. Measurement of the Effects of Crude Oil Fractions on Rock Wettability No entirely satisfactory method for measuring rock wettability has yet been developed. All methods used are empirical. The imbibition test was used in these studies. This test is based on the tendency of a rock to imbibe the wetting phase spontaneously. For example, if a strongly water-wet rock is first saturated with oil and then placed in water, the water will quickly invade the rock by capillarity and much of the oil will be displaced. If the rock is slightly water-wet, water irnbibition will proceed more slowly and, in many instances, considerably less oil will be displaced. A water-saturated, oil-wet rock will imbibe oil. The initial rate with which water (or oil) imbibition takes place indicates, qualitatively, the degree of water (or oil) wettability of the rock.

By C. A. O’Malley, F. W. Kinsey

This paper deals with an experimental study in the use of a preagglomerated burden as a means of increasing the production of sinter. The effect of a wide range of sinter burden was studied, including concentrates produced by a flotation process. Some of the important characteristics of a sinter bed are discussed along with the strength and reducibility of the sintered product. In recent years the use of sinter in blast furnaces has become increasingly important across the country—largely because of the demand for more hot iron from existing plant capacity and the increasing amount of fines in the burden materials available to the blast-furnace operator. In many instances, unfortunately, the demand for sinter has been so great that little time has been available to give the proper

Jan 1, 1960

By John S. Alexander

DURING the past few years the block coal of Indiana has been talked about and written upon to such an extent, that almost every one at all interested in such subjects, has been made acquainted with the area and geographical position of the field, the quality and peculiar properties of the coal, the thickness of the veins, the manner of mining, etc. The writer, therefore, taking for granted that, to those present all this is familiar ground, desires more especially to call attention to the position this coal takes in the market, and at those points of consumption where it is brought in direct competition with rival fuels. Chicago, thus far, has been the chief consumer of Indiana block coal, the distance from the mines at Brazil, via Terre Haute and the

By C. Gatlin, M. E. Chenevert

The effects of bedding plane orientation on the elastic constants and the yield strengths of three laminated rocks (one sandstone and two shales) and one isotropic rock (a limestone) were studied. The directional dependence of the elastic properties of these rocks was experimentally evaluated using a triaxial compression cell and auxiliary stress-strain measuring equipment. Symmetry of Poisson's ratios within the bedding plane suggested that horizontal isotropy exists, but the bedding planes do give rise to an appreciable difference between properties in the horizontal and vertical directions. For the three bedded rocks studied, Young's modulus was lower normal to bedding than along bedding. Yield strengths were determined at confining pressures from 0 to 12,000 psi in a triaxial compression cell. The rocks studied showed strength reductions as high as 40 per cent when the test specimen was oriented at 20°-30° to the bedding planes. The mechanical behavior of these rocks suggested that the rock properties of shear strength and/or coefficient of internal friction can vary with direction, depending on the particular rock tested. Tensile strengths were also measured and found to be lowest when failure occurred along bedding. This work shows that bedded formations exhibit sizable directional variations in both their elastic constants and yield strengths. It is suggested that these variations may be accounted for by using the "elastic laminate" model and the "variable coefficients" failure model. INTRODUCTION The nature of rock deformation at elevated pressures has been studied by many workers; papers by Handin,l,2 and Robinson3 illustrate the present state of knowledge. Most investigators have either chosen rocks which were as isotropic as possible (in order to avoid complications of data interpretation and analysis) or they have oriented their samples so that the effects of anisotropies (such as bedding planes) have been avoided. Of the studies performed, few were concerned specifically with mechanical anisotrop-ies. Griggs4 has presented limited data for specimens cut parallel, normal, and 45° to the bedding plane; he relates the strength anisotropy observed to the fabric (bedding) anisotropy. His tests were primarily concerned with large deformations (20 per cent strain); thus, no directional values of the elastic constants were reported. Handin has reported the results of similar experiments. Bott5has discussed rock strength anisotropies due to faults, cleavage, or bedding. He was concerned primari ly with determining the shear stress on such planes and did not mention the effect of friction. Jaeger6 later generalized Bott's work by taking friction into account and presented a limited theory for the failure of rocks having a "single plane of weakness", and also for rocks having a constant coefficient of friction, and a shear strength which varies with bedding plane orientation. Donath and Cohen,7 and Donathg have evaluated rock strengths from shale and slate specimens cut normal and parallel to bedding. A dependence of cohesive strength (7,) on the specimen orientation was also shown. Adler9 has also studied this problem and lists similar results. He assumes that all bedded rocks behave according to Jaeger's single-plane-of-weakness theory. Kalinin and Belorussov10 list results for strength tests parallel and perpendicular to bedding and use this information as a basis for hole deviation analysis. From the literature it is apparent that sedimentary rocks have been tested under widely varying conditions of stress; however, the assumption of isotropy is generally, but not always, made. Since geologic sedimentation often deposits sediments in very definite lavers.,. it seems that more svstema tic attention should be given to the possible effects of this natural bedding. Bedding, as used here, refers to visible regularities of grain size or orientation resulting from depositional processes. The mechanical strength anisotropies, which bedding may present, is not the only anisotronic property to be considered, since the elastic

Jan 1, 1966

By Charles R. Holmes

MORE than 70 igneous pipes and dikes are known to occur in Cambrian sediments throughout an approximately circular area of about 75 sq miles in southwestern Ste. Genevieve County and southeastern St. Francois County, Mo., across the southern portion of the Farmington anticline, which is outlined in fig. 1. From evidence obtained from fossil fragments taken from some of the in-trusive~, and from the similarity in composition of the more basic intrusives to those of known age in surrounding states, these pipes and dikes are believed to be at least post-Devonian and probably Cretaceous in age. As first postulated by Rust,' these intrusives are believed to represent explosion tubes, or diatremes, punched through great thicknesses of solid rock by gaseous pressure. The particular intrusive studied is located about 1 mile north of the small town of Avon at an elevation of 880 ft in the EVz SEy4 NEY4 of see. 2, T. 35N, R. 7E. Outcrop is through the Bonneterre dolomite in two separated exposures. The larger outcrop extends east and west for about 50 ft along a tributary in a small ravine (fig. 2). The smaller exposure occurs as a few scattered patches over an area 20 ft square about 100 ft to the north. The area between the exposures is covered, but scattered patches of the Bonneterre dolomite outcrop throughout the area surrounding the diatreme. Where exposed, contact relations show the surrounding dolomite to be shattered and metamorphosed to a fine-grained rock for a distance of 15 to 20 ft from the intrusive. The igneous rock occurs as a dark greenish-gray porphyry near the center of the diatreme and as a fine-grained, greenish-gray material containing lapilli and metamorphosed fragments of dolomite near the contact with the country rock. The most abundant original mineral of the porphyritic rock is olivine now largely serpentinized as the result of extensive hydrothermal alteration at time of emplacement. The most common constituent of the fine-grained rock, which occurs near the border of the intrusive, is calcite. Mica is a common constituent of both types of rock, occurring as tufts or flakes. Magnetite makes up about 2 pct of the diatreme and occurs as small irregular grains or streaks of tiny grains. Singewald and Milton' have termed the rock of this body an "augite-free alnoite." Susceptibility measurements of pulverized specimens were made from selected samples taken from both the diatreme and the surrounding country rock. The susceptibility of the Bonneterre dolomite was found to be less than 40xlO-6 cgs (centimeter-gram-second) units and that of the metamorphosed contact dolomite less than 200x10-6 cgs. Measurements of individual samples of the igneous rock showed a wide variation in susceptibility between limits of 1000x10-6 cgs to 8000x10-6 cgs, with the maximum difference occuring in samples taken only a few feet apart. The maximum value was exhibited by a highly weathered sample taken from the northern outcrop, while minimum susceptibility was determined from a partially weathered sample taken only a few feet away. These extremes are believed to represent small local concentrations of stringers and grains of magnetite crystals in the igneous rock. A detailed magnetic survey of the horizontal and vertical components of the earth's magnetic field was made over the diatreme area. Stations were occupied at 20-ft intervals as shown by the grid on fig. 2. When greater detail was desired, intervening stations were also occupied. The field instruments were supplied by the Department of Geophysics, St. Louis University. The magnetometers are the Schmidt balance type constructed by the Ruska Instrument Co. These instruments are temperature compensated and have a standard sensitivity of 10 gamma. Calibration of the instruments

Jan 1, 1951

By Charles R. Holmes

MORE than 70 igneous pipes and dikes are known to occur in Cambrian sediments throughout an approximately circular area of about 75 sq miles in southwestern Ste. Genevieve County and southeastern St. Francois County, Mo., across the southern portion of the Farmington anticline, which is outlined in fig. 1. From evidence obtained from fossil fragments taken from some of the in-trusive~, and from the similarity in composition of the more basic intrusives to those of known age in surrounding states, these pipes and dikes are believed to be at least post-Devonian and probably Cretaceous in age. As first postulated by Rust,' these intrusives are believed to represent explosion tubes, or diatremes, punched through great thicknesses of solid rock by gaseous pressure. The particular intrusive studied is located about 1 mile north of the small town of Avon at an elevation of 880 ft in the EVz SEy4 NEY4 of see. 2, T. 35N, R. 7E. Outcrop is through the Bonneterre dolomite in two separated exposures. The larger outcrop extends east and west for about 50 ft along a tributary in a small ravine (fig. 2). The smaller exposure occurs as a few scattered patches over an area 20 ft square about 100 ft to the north. The area between the exposures is covered, but scattered patches of the Bonneterre dolomite outcrop throughout the area surrounding the diatreme. Where exposed, contact relations show the surrounding dolomite to be shattered and metamorphosed to a fine-grained rock for a distance of 15 to 20 ft from the intrusive. The igneous rock occurs as a dark greenish-gray porphyry near the center of the diatreme and as a fine-grained, greenish-gray material containing lapilli and metamorphosed fragments of dolomite near the contact with the country rock. The most abundant original mineral of the porphyritic rock is olivine now largely serpentinized as the result of extensive hydrothermal alteration at time of emplacement. The most common constituent of the fine-grained rock, which occurs near the border of the intrusive, is calcite. Mica is a common constituent of both types of rock, occurring as tufts or flakes. Magnetite makes up about 2 pct of the diatreme and occurs as small irregular grains or streaks of tiny grains. Singewald and Milton' have termed the rock of this body an "augite-free alnoite." Susceptibility measurements of pulverized specimens were made from selected samples taken from both the diatreme and the surrounding country rock. The susceptibility of the Bonneterre dolomite was found to be less than 40xlO-6 cgs (centimeter-gram-second) units and that of the metamorphosed contact dolomite less than 200x10-6 cgs. Measurements of individual samples of the igneous rock showed a wide variation in susceptibility between limits of 1000x10-6 cgs to 8000x10-6 cgs, with the maximum difference occuring in samples taken only a few feet apart. The maximum value was exhibited by a highly weathered sample taken from the northern outcrop, while minimum susceptibility was determined from a partially weathered sample taken only a few feet away. These extremes are believed to represent small local concentrations of stringers and grains of magnetite crystals in the igneous rock. A detailed magnetic survey of the horizontal and vertical components of the earth's magnetic field was made over the diatreme area. Stations were occupied at 20-ft intervals as shown by the grid on fig. 2. When greater detail was desired, intervening stations were also occupied. The field instruments were supplied by the Department of Geophysics, St. Louis University. The magnetometers are the Schmidt balance type constructed by the Ruska Instrument Co. These instruments are temperature compensated and have a standard sensitivity of 10 gamma. Calibration of the instruments

Jan 1, 1951

By N. J. Themelis, A. W. Last

Autogenous grinding, broadly defined as the self-comminution of ore in a cylindrical tumbling mill without using auxiliary grinding media, was first applied in the early 1930s in the so-called Hadsel mills (Hardinge, 1955) as seen in [Fig. 1], mainly used in gold mines on the US West Coast. A number of these mills were built in sizes of 6.1 to 7.3 m (20 to 24 ft) in diameter and 1.5 to 1.8 m (5 to 6 ft) in length but were later abandoned because of operating and maintenance problems. Further development of autogenous grinding led to the Hardinge wet grinding mill, the Aerofall dry grinding mill, and others. A tabulation of all known autogenous and semiautogenous installations around the world was sent recently to the authors by G. J. Kushner of Koppers Metal Processing Division. In the size range of 7.3 to 9.8 m (24 to 32 ft) in diameter, it lists a total of thirty mills used in the processing of copper ores. An additional 120 units are listed in the same size range for the processing of iron ores and other minerals. The largest mills in existence are 11.1-m-diam X 4.6-m-long (36-ft-diam X 15-ft-long) mills in Minnesota, powered by 8950 kW (12,000 hp) motors and used in taconite beneficiation. It is indicative of the phenomenal growth of this technology that none of the above 150 mills was in operation prior to 1964. Grinding rates in autogenous mills are very sensitive to variations in ore breakage characteristics and even with fairly constant ore type can exhibit large fluctuations in throughput. Autogenous grinding also depends on availability of a fraction of the ore to be ground in the form of "competent" rock which can withstand to a certain degree the tumbling and impact action within the mill. If the ore is uniformly "soft", it will soon be crushed into small size particles and further grinding, which depends on the existence of large size rocks in the mill, becomes impossible. This apparently is the case with most copper ores, as discussed by Bachman, Last and Nabbs (1970) who described pilot testing of a large number of ore samples from Kennecott 's Chino Mines. Under circumstances where autogenous grinding is impractical, it is possible to realize most of its benefits by utilizing large grinding balls in place of the "competent" rock and practice what has become known in the mining industry as semiautogenous grinding. In semiautogenous grinding (SAG), a grate discharge tumbling mill is fed the product of a primary crusher or run-of-mine rock. Forged steel or alloy grinding balls, in proportions ranging from 3.10% of the total volume in the mill, are used to complement the self-grinding ability of the ore. Semiautogenous circuits can be either designed for single-stage closed-circuit grinding which produces a final product for recovery processes, or for two-stage operation in which the SAG mill product is fed to a second stage of grinding in a conventional ball mill.

Jan 1, 1981