Search Documents

By D. W. Carter, K. M. Fagin

Six new oil fields were discovered in the East and East Central Texas district during 1942. The Coke and Quitman fields, in Wood County, at this time appear to be the two most important oil discoveries for the year. The. four other oil fields discovered were Concord, in Anderson County; Kildare, in Cass County; Weiland (ClubLake), in Hunt County; and Larissa, in Cherokee County. The Rodessa lime in the Chapel Hill field, Smith County, provided the only new oil zone in older fields. The Hawkins field, Wood County, was the most active in drilling operations, 125 new wells being completed during the year. The Chapel Hill field tied the Coke field for second place with 30 completions each. The third most active field was Kildare, with 10 completions. Like the other oil-producing districts of the country, wartime restrictions reduced the number of oil and gas-well completions to 265 in 1942, compared with 964 completions in 1941. This represents a drop of 72 per cent and only a little more than one half enough to replace the 437 producing wells abandoned in the district during the year. Tn addition, the number of producing wells temporarily shut down nearly tripled, far two principal reasons: (I) the rule of the Petroleum Administration for War preventing operators from equipping more than, one well on each 10 surface acres with pumping or artificial-lift equipment, and (2) the Railroad Commission's issuance of various orders permitting the transfer of allowable for wells having high water-oil ratios and high gas-oil ratios to other wells capable of producing the same with less waste of reservoir energy. No changes were made in prices of crude oil in the district during 1942. Production and Probation The district produced 158,928,281 bbl. of oil and distillate during 1942, compared with 163,566,695 bbl. during 1941, which represents a decrease of 3 per cent. The East Texas field produced 120,680,595 bbl. of oil, compared with 130,377,793 during 1941; a reduction of 9,697,198 bbl., or 7.4 per cent. The production of this field represents 75.9 per cent of the district total, compared with the 79.7 per cent that it furnished in 1941. The district had an estimated basic daily oil allowable of 623,242 bbl. on Dec. 31, 1942. Approximately 31.8 per cent of the production in Texas during 1942 was supplied by this district, compared with 33 per cent during 1941- Changes in the annual production of newer and flush fields in this district are attributable either to a difference in the number of wells producing during the year or to changes in basic allowable and number of shutdown days due to shifting market dconditions brought on by the war. All regularly prorated fields in the district were shut down 123 days. Major exceptions were the East Texas field, closed128 days; Hawkiis, shut down 106 days; and Cayuga, Sulphur Bluff, Talco, and Rodessa, which

Jan 1, 1943

By R. C. Buehl, J. P. Riott, E. P. Shoub

PILOT-PLANT tests have demonstrated that it is possible to produce low-sulphur sponge iron (0.03 to 0.05 per cent sulphur) as a continuous process in an internally fired rotary kiln from iron ore or mill scale; a solid carbonaceous reducing agent; and dolomite to control the sulphur content. The proportion of dolomite employed is small, so that it does not add materially to the cost of the sponge iron. The entire operation is carried out at temperatures well below the melting point of iron, so that the product is discharged in granular form. Compared with other methods for the production of sponge iron, the rotary-kiln method has the advantage of simplicity and low cost of equipment and; in addition, requires little labor for the operation of the process. The pilot-plant equipment used for this work was sufficiently large to demonstrate that the production of low-sulphur sponge iron in rotary kilns is feasible and that the costs are not excessive for applications in which sponge iron has distinct advantages over competing materials. This report constitutes a part of a program by the Bureau of Mines under a special Congressional appropriation for studying gaseous and solid fuel reduction of iron ores. Numerous articles on various phases of these investigations have appeared in Bureau of Mines publications or technical journals. Other articles are being prepared and will be published in the near future. The present program, which is under the supervision of Dr. R. S. Dean, Assistant Director of the Bureau of Mines, was initiated in .1942. However, a considerable portion of the work was a continuation of previous research performed by the Bureau. Previous investigators1-4 utilizing the rotary kiln for the production of sponge iron did not develop a suitable method for controlling the sulphur content. A review of the literature shows that the sulphur content in the product usually exceeded 0.2 -per cent unless reducing agents with very low sulphur contents were employed. This high sulphur value made the product generally undesirable for use as melting stock in electric or open-hearth furnaces. The production of sponge iron in an internally fired rotary kiln has been described in detail in Bureau of Mines Bulletin 2702; consequently, this article will be confined mostly to new features of the process-that is, means for controlling the sulphur content of the sponge iron. Suitable raw materials include iron ores or mill scale; coal or coke for reducing them, and sized dolomite (-20+100-mesh) as the sulphur-controlling agent. A mixture of the raw materials in granular form is fed into the elevated end of the kiln, which is fired axially from the lower or discharge end. In the reducing zone, which is approximately one third the length of the kiln measured from the dis-

Jan 1, 1946

By J. Gurland

The wmk is concerned with the estimate of the degee of continuity of a particulate phase dispersed in a matrix. The first section is a verieu: of the parameters nzeasurable by quantitative rnetallogvaphy, namely the contact area and, under certain conditions, the number of contacts between particles of one phase. In the second section, the frequency of particle contacts is related to the degee of continuity of a randomly embedded phase orz the basis of the lattice-percolation model of Hamrnersley and others. THE extent of continuity of the constituent phases may greatly influence the structure-sensitive properties of phase mixtures, particularly if the phase properties differ significantly. An example from the literature1 is shown in Fig. 1. The marked decrease of the electrical resistivity of sintered silver-alumina bodies near 25 pct by volume of silver presumably occurs because the more conductive phase changes from a discontinuous to a continuous structure. Other example of electrical- and thermal-conductivity transitions are cited by kingery In view of these observations, a knowledge and understanding of the connectivity of the microstructure may be of considerable practical importance. This study is concerned with one aspect of the genera1 problem, namely the estimate of the degree of continuity of a particulate phase dispersed in an opaque matrix. The first section reviews the parameters measurable on a polished cross section by auantitative metallography, such as the contact area and under certain conditions, the number of contacts between particles of one phase. In the second section, an attempt is made to relate the frequency of particle contacts to the degree of continuity of a randomly embedded phase. For the purpose of this discussion, the aggregate has two constituents: the particulate phase and the matrix. The latter is considered to be homogeneous. The term "particle" is used with the meaning of "grain", i.e., a minute unit of matter which is usually a single crystal of a readily distinguishable substance within the confines of a simply connected boundary. While many of the concepts which are used here to describe the structural variables characterizing the microstructure of phase mixtures are qualitative and ill-defined, they are presented with the intent of stimulating further work of a more general and rigorous nature. I) PARTICLE CONTACT, CONTIGUITY, AND MEAN FREE PATH 1) Measurement of Contiguity. The fraction of the total internal surface of a phase a shared with particles of that same phase in a two-phase mixture of and $ is indicated by the contiguity ratio:3 whereis the area of the interface between o particles, and Sap is the area of the interface between a particles and matrix P, per unit volume of mixture. The contiguity ratio ranges from 0 to 1 as the distribution of the a phase changes from a completely dispersed to a completely agglomerated structure. The interfacial areas may be obtained from simple intercept measurements on a random plane, after Smith and Guttman where and N are the numbers of intercepts between a random line of unit length on a plane of polish and the interparticle and interphase interfaces, respectively. The equations are valid for any distribution of particle sizes and shapes.

Jan 1, 1967

Sept. 3-8, AIME, Fall Meeting, Industrial Minerals, Minerals Beneficiation, Mining, Geology, & Geophysics, Iron and Steel, and Coal Div., Palmer House, Chicago. Sept. 3-13, AIME, Chicago Section, Centennial of Engineering, Chicago. Sept. 5-8, Engineers' Council for Professional Development, annual meeting, Hotel Sheraton, Chicago. Sept. 11-13, American Institute of Chemical Engineers, Palmer House, Chicago, Ill. Sept. 13, Columbia Section, AIME, Canadian Institute of Mining and Metallurgy, joint all-day meeting, Metaline Falls, Wash. Sept. 18, AIME, Utah Section, Newhouse Hotel, Salt Lake City. Sept. 20, Colorado Section, AIME, Denver. Andrew Fletcher, speaker. Sept. 22-25, American Mining Congress, Metal and Nonmetallic Mining Convention and Exposition, public auditorium, Denver. Sept. 23-25, Institution of Mining and Metallurgy, symposium on mineral dressing, Royal School of Mines. London.

Jan 1, 1952

By R. P. Aikman, F. G. Miller, J. M. Podgursky

As part of a larger study of the mechanism of froth flotation of coal, the rates at which coal particles of various size and specific gravity react to froth flotation were investigated. Results of this study show that in flotation: I) recovery rate increases, but selectivity decreases with a decrease in particle size down to 100 mesh, and 2) recovery rate is constant for all sizes between 100M and 325M. n response to the growing demand for low-sulfur coking coal for iron making, the coal industry is continually striving to perfect methods for cleaning coal to acceptable ash and sulfur levels while maintaining maximum product yield. By present standards the industry has adequate processes for cleaning coarse coal, i.e., + 28 mesh, at almost any desired specific gravity. However, in the case of fine coal, i.e., —28 mesh, neither of the two existing processes - froth flotation or hydrocycloning — in its present state of development yields products that are comparable in ash and/or sulfur content to products normally obtained from coarse coal processes. The work outlined in this paper is part of a larger study directed toward maximum exploitation of froth flotation for fine coal processing. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of froth flotation with other fine-coal processing methods. The paper includes: 1) A discussion of the value of a detailed wash-ability study as a method of assessing the problems associated with fine coal processing, 2) A general discussion of hydrocyclone principles, included to serve as a basis for understanding the mechanism of coal flotation, and 3) A detailed discussion of the mechanism of coal flotation, as well as the research leading to the optimum use of froth flotation in combination with other fine-coal cleaning methods to provide efficient fine-coal processing. Our study of the rates at which coal particles of various size and specific gravity react to flotation shows that in flotation: 1) recovery rate increases but selectivity decreases with a decrease in particle size down to 100 mesh, 2) recovery rate is constant for all sizes between 100 mesh and 325 mesh, and 3) the flotation process effectively rejects only those extremely fine particles which do not contain surface carbon. (Because of this feature, froth flotation is an excellent method for rejecting clays - the only extreme fines in - 325-mesh coal that are always carbon free.) Washability studies of flotation products are used to assess flotation efficiency. These studies show that: 1) the increase in percent sulfur in flotation products above the theoretical sulfur content as defined by the washability study is due almost entirely to flotation of fine high-specific-gravity particles that are part coal and part pyrite, and 2) in a given size range particle floatability decreases with an increase in particle specific gravity. Error curves are explained and are used to compare the mechanisms of coal flotation and hydrocycloning. These comparisons show that hydrocyclone performance is affected primarily by particle mass, i.e., particle specific gravity and size, whereas coal flotation performance is dependent on both the particle mass and the coal surface available for bubble attachment. Since the error curve is a basic tool for rating the efficiency of any coal processing system, it will be useful to quickly review the principles of error curve construction. RATING COAL-PROCESSING EFFICIENCY BY THE ERROR CURVE The organic component of coal is of lower specific gravity than its impurities, and the most effective principle for coal concentration is therefore separation on the basis of specific gravity. However, since there is no sharp dividing line between pure coal and pure ash components, specific gravity must be closely controlled if the product is to have acceptable quality at maximum yields. In turn, the basis for close control in any coal processing system is the reference standard provided by precise laboratory washability studies. In these studies, coal is carefully separated into a series of progressively higher specific gravity fractions to establish a relationship

Jan 1, 1968

By G. W. P. Rengstorff

In an effort to find an oxidation-resistant alloy of molybdenum, binary and ternary alloys containing aluminum, chromium, cobalt, iron, nickel, silicon, titanium, tungsten, vanadium, and zirconium were screened. Fourteen other alloying additions were also tested. Many of the alloys were more oxidation-resistant than molybdenum, but none were entirely satisfactory. MOLYBDENUM oxidizes extremely rapidly above 1450°F in air. At 1800°F, a loss of metal at the rate of 0.1 in. in 4 hr is typical. The high speed of this oxidation may be judged by comparison with the oxidation rate of 0.1 in. per year (0.00005 in. in 4 hr), sometimes taken as the maximum permissible oxidation rate at 1800°F for a satisfactory Fe-Cr-Ni alloy. Great strides have been made in the development of coatings and cladding to protect molybdenum from oxidizing atmospheres. These developments in surface protection will undoubtedly make it possible to take advantage of the excellent hot strength of molybdellum and its alloys in many new applications. Still, even the best coating can protect molybdenum only as long as the surface layer is unbroken. Research was undertaken to determine whether an alloy of molybdenum could be found which would resist oxidation. Such an alloy would not deteriorate suddenly when the protective surface layer was destroyed in a small area. In seeking an alloy of molybdenum to resist oxidation, the physical properties of molybdenum could not be sacrificed entirely. The development of an alloy with the desired resistance to oxidation was not achieved. The information obtained on the effect of a large number of elements on the oxidation of molybdenum is, however, of value in the development of coatings. Indeed, many of the alloys tested for oxidation resistance were already known to have poor mechanical properties but were tested to aid in the development of coatings. Oxidation of Molybdenum The rapid oxidation of molybdenum is usually attributed to the volatility of Moo,,. Gulbransen and Wysong have shown that molybdenum oxidizes very slowly up to 850°F, the temperature at which the oxide film begins to evaporate. Melting as well as evaporation of molybdenum oxides promotes the oxidation of molybdenum. MoO melts at 1465°F. MOO, the oxide which is believed to form at the metal-oxide interface, combines with MoO, to form a eutectic having a melting point of 1432°F.' The liquid oxide, even if nonvolatile, could cause poor resistance to oxidation by allowing easy transport of molybdenum and oxygen ions through the oxide. Actually, a sudden increase in the rate of oxidation of molybdenum at 1460°F has been observed to coincide with the appearance of a liquid phase. The formation of a volatile oxide is not unique with molybdenum. The problem is also encountered with vanadium, tungsten, and some of the Pt-Pd group of metals. Vanadium not only forms the volatile V2O3 but, like molybdenum, forms a liquid oxide coating. Few attempts have been made, however, to prevent the rapid oxidation of these metals by alloying. Oxidation of Molybdenum Alloys At the beginning of this work, very little was known of the oxidation resistance of molybdenum alloys. It was known that molybdenum disilicide (with 37 pct Si) has extremely good oxidation resistance,' but this compound is so brittle that it has few uses. It is an effective protective coating for molybdenum when allowance can be made for its brittleness. Chromium was known to retard the oxidation of molybdenum,' but at least 50 pct Cr was necessary to have an appreciable effect. Other, unpublished, reports show that a few other alloys have been given preliminary tests, but the results have not been promising." Choice of Alloys to be Investigated An alloying element might be expected to protect molybdenum in either of two ways: Its oxide might combine with molybdenum oxide to form a stable, nonvolatile complex oxide (a molybdate); or the oxide of the alloying element might form in preference to molybdenum oxide, developing an impervious layer which would prevent the formation of a volatile molybdenum oxide. The knowledge available about the formation of molybdates was meager. Therefore, the initial study was made on alloys of molybdenum with elements having especially stable oxides. On this basis, binary and ternary alloys containing the following six elements were investigated: aluminum, chromium, titanium, zirconium, silicon, and vanadium. Nickel was also added as an alloying element. Although it does not form a more stable oxide than molybdenum, it does impart some oxidation resistance to copper and iron. Its inclusion in the study was fortunate because its alloys proved to be the most promising of those first tested. Apparently nickel formed a stable molybdate. Because nickel was effective in reducing the oxidation rate of molybdenum, the elements iron, cobalt, and tungsten were added to the list. The ten alloying elements mentioned form ten binary and 45 ternary alloying systems with molybdenum. A series of alloys was tested in each of these systems. In addition, at least one test was made on the effect of each of the following alloying elements:

Jan 1, 1957

By Axel Hultgren, B. Herrlander

THE original aim of the present investigation was to study the mechanism of cracking on hot-deforming red-short steels. During the microscopical examination of hot-deformed soft steels attention was directed to various patterns of so-called veining in the ferrite, as related to variations in the deformation procedure and the heat-treatment of the steels. Later, a hot-short steel of higher carbon content was also studied. Historical Storey1 suggested in 1914 that veining developed during the gamma-alpha transformation from the growing together of several alpha nuclei within the same gamma grain. Rawdon and Berglund2 found that in soft steel, forged somewhat below A3, the ferrite showed profuse veining, while usually there was very little veining after forging at very high temperatures. They emphasized the similarity between the pattern of veining formed by deformation about 600°C and that of slip lines formed by deformation at room temperature. They also suggested a relation between the gamma-alpha transformation and veining. They became convinced from etching and from the slip-line pattern in cold-deformed material, that the orientation within any ferrite grain showing veining was uniform. In recrystallized alpha grains veining was absent. Veining did not appear materially to affect the properties of ferrite. Independent of veining, continuous networks, attributed to preexisting delta and gamma grain boundaries were sometimes found, the former only in cast steel. Those networks were usually connected with small inclusions. Ammermann and Kornfeld3 confirmed that recrystallized ferrite grains showed no veining. In soft steel annealed between At and A3 there was veining only in the ferrite grains formed during cooling. Electrolytic iron deformed at 880° was free from veining. Bannister and Jones4 considered veining in ferrite to be a manifestation of microscopical and submicroscopical inclusions. Northcott,5,6 in studies on veining in steel and other metals and alloys, attributed veining to oxide inclusions. It could generally be removed by annealing in hydrogen, a suggestion earlier made by Rawdon and Berglund. Tritton (discussion in ref. 5) emphasized the importance of perfect polishing for bringing out veining by etching, and thought the veins or subboundaries were produced during the gamma-alpha transformation, when it was rapid, as a result of the volume change and contraction during cooling.

Jan 1, 1946

By Charles E. Lundin

Pressure-temperature-composition data were obtainedfor the Er-H system. Measurements werecar-ried out in the temperature range of 473° to 1223°K, the composition range of erbium to ErH,, and the pressure range of 10-5 to 760 Torr. Solubility relationships were established from these data throughout the system. Three solid-solution phases were delineated: metal solid solution, dihydride phase, and trihydride phase. The trihydride Phase decomposes at about 656°K and 1 atm pressure. The dihydride phase is stable to about 1023°K, but becomes more deficient in hydrogen above this temperature. The equilibrium decomposition pressure-temperature relationships in the two-phase regions, erbium solid solution plus dihydride and dihydride plus trihydride, were deter- The differential heats of reaction in these two regions are AH = - 52.6 * 0.3 and - 19.8 i 0.2 kcal per mole of Hz, respectively. The differential entropies of reaction are AS = - 35.2 * 0.3 and - 30.1 * 0.4 cal per mole HZ.deg, respectively. Relative partial molal and integral thermodynamic quuntities were calculated in the system to the dihydride phase. RARE earth metal-hydrogen systems have been the subject of general survey,1"4 and all have been found to form hydride phases. The heavy rare earths, of which erbium is a member, form dihydride and trihydride phases with different crystal structures, whereas the light rare earths form only a single-phase dihydride which expands without structure change, as hydrogen is added, to the trihydride composition. These materials are of interest primarily because of their theoretical properties, such as bonding, defect structure, and thermodynamic and electronic characteristics. Erbium has been studied in several previous investigations.5, 6 It was deemed desirable to more thoroughly and accurately define the system, both for the phase equilibria and the thermodynamic properties. I) EXPERIMENTAL PROCEDURE A Sieverts&apos; apparatus was employed to conduct the experimental measurements. Briefly, it consisted of a source of pure hydrogen, a precision gas-measuring buret, a heated reaction chamber, a mercury manometer, and two McLeod gages (a CVC, GM 100A and CVC, GM 110). Pure hydrogen was obtained by passing hydrogen through a heated Pd-Ag thimble. The hydrogen was analyzed and found to have only a trace of oxygen and nitrogen. A 100-ml precision gas buret graduated to 0.1-ml divisions was used to measure and admit hydrogen to the reaction chamber. The reaction unit consisted of a quartz tube surrounded by a nichrome-wound furnace. The furnace temperature was controlled by a recorder-controller to ±1°K. An independent measurement of the sample temperature in the quartz tube was made by means of a chromel-alumel thermocouple situated outside, but adjacent to, the quartz tube near the specimen. Pressure in the manometer range was measured to ±0.5 Torr and in the McLeod range (10-4 to 10 Torr) to ±3 pct. The hydrogen compositions in erbium were calculated in terms of hydrogen-to-erbium atomic ratio. These compositions were estimated to be ±0.01 H/Er. The erbium metal was obtained from the Lunex Co. in the form of sponge. The metal was nuclear grade with a purity of 99.9 pct +. The oxygen content was reported to be 340 ppm and the nitrogen not detectable. Metallographically the structure was almost free of second phase (<1 vol pct). A quantity of sponge was arc-melted for use as charge material. The solid material was compared with the sponge in the pressure-temperature-composition relationships. They were found to be identical. Therefore, sponge material was used henceforth, so that equilibrium could be attained more rapidly. The specimen size was about 0.2 grain for each loading of the reaction chamber. The procedure employed to obtain the pressure-temperature-composition data was to develop experimentally a family of isothermal curves of composition vs pressure. First, a specimen of erbium was wrapped in a tungsten foil capsule to prevent contact with the quartz tube. After loading the specimen, the system was evacuated to less than l0-6 Torr, flushed several times with high-purity hydrogen, and evacuated again ready for the start of the experiment. The furnace was then brought to the desired temperature. A measured amount of hydrogen was admitted into the chamber. Equilibrium was allowed to be attained, the pressure read, and the process then repeated many times until 1 atm of gas pressure was finally reached. Other isotherms were then developed in the same manner. The partial pressure plateaus were determined by another manner. In the solid solution-dihydride region a composition of approximately 1.0 H/Er was selected on the plateau. The temperature was varied throughout the range of interest. At each temperature level, equilibrium was achieved, the pressure read, and the next temperature attained. The temperature was cycled both up and down. In the dihydride-trihy-dride region, the plateaus were determined in the 473" to 651°K range only by heating to the desired temperature and not by both heating and cooling. The data were much more reproducible in this manner. Equilibrium required long periods of time. Specimens were initially hydrided to 2.8 H/Er, so that at the higher

Jan 1, 1969

By Robert E. Green, Kenneth Reifsnider

Several experiments have been performed in order to illustrate the application of a recently developed X-ray image intensifier system to metallurgical investigations. In the present work the system has been used to study the instantaneous alterations in Laue transmission X-ray diffraction patterns during tensile deformation of aluminum single crystals. Expem&apos;mental results are presented which demonstrate the capability of the system for crystal orientation, for following orientation changes due to lattice rotation during tensile deformation, and for showing changes in the homogeneity of the lattice planes along the specimen length as a function of strain rate. RECENTLY, a new X-ray system has been developed which incorporates a cascaded image intensifier and permits direct viewing and recording of X-ray diffraction patterns produced on a fluorescent screen.1"3 In the present work the results of several experiments are presented which demonstrate the usefulness of this system for metallurgical applications. EXPERIMENTAL PROCEDURE A schematic diagram of the experimental arrangement is shown in Fig. 1. In this system a Machlett AEG-50-S tungsten target X-ray tube, normally operated at 50 kv and 40 ma, serves as the X-ray source. The X-ray tube is placed in direct contact with a 10-in.-long collimator, which transforms the X-ray beam from one with a circular cross section to one with a rectangular cross section 3 in. high and 1/6in. wide. By blocking off all but a small portion of the rectangular slit, it is possible to work with the more conventional "pinhole" collimated X-ray beam commonly used for obtaining Laue diffraction patterns. In the present work the test specimens were 99.99+ pct aluminum single crystal wires & in. in diam and 3 in. long. For the deformation tests the wire crystals were mounted in a special set of grips in a table model Instron machine so that diffraction patterns could be recorded during specimen deformation. For the orientation tests the wire crystals were mounted in a rotating goniometer so that diffraction patterns could be recorded during specimen rotation. At a distance of 3 cm from the specimen axis, a 6 in. diam DuPont CB-2 fluorescent screen is positioned to transform the X-ray image to a visible one. A Super Farron f/0.87 72 mm coupling lens, corrected for 4 to 1 demagnification, transmits the visible image to the image tube. The image intensifier used is a three-stage magnetically focused RCA type C70021A with an S-20 input photocathode and a P-20 output phosphor. The tube has unity magnification and useful input and output screen diameters of 1.5 in. The image on the output phosphor is of sufficient intensity to be viewed directly, to be recorded cine-matographically, or to be displayed by vidicon pick-up on a television monitor. The recording device most commonly used is a 16 mm Bolex motion picture camera fitted with a Canon f/0.95, 50 mm lens. The overall gain of the system is 16,000 for direct viewing and 2240 for recording on 16 mm movie film. The resolution of the system is limited to 1 line pair per mm which is approximately that of the fluorescent screen. This system has been used for cine recording of transmission Laue X-ray diffraction patterns with exposure times as short as 1/220 sec and for vidicon television pick-up and display at a scan time of 1/30 sec. Quantitative information may be obtained from each frame of the movie film, by either stopping the vertical slit down to a point source in order to obtain a conventional Laue photograph or else by retaining the linear beam and introducing fiducial marks as described in a previous paper.4 In either case, each frame may be enlarged to appropriate size for analysis by either using a photographic enlarger and making prints of the desired frames, or, more conveniently, by using a microfilm reader. EXPERIMENTAL RESULTS The first series of photographs which are presented in Fig. 2 serves to demonstrate the usefulness of the system for crystallographic orientation determination. This series of prints, made from enlargements of a 16 mm movie film, shows the dynamic Laue transmission patterns produced by an aluminum single crystal wire which was rotating about the wire axis when the patterns were recorded. The movie films were taken at 16 frames per sec and the crystal was rotated at a rate of 15 rpm.

Jan 1, 1970

By Ralph Arnold

While much geological work and drilling have been done in Venezuela, the incompleteness of geological evidence obtainable and the restricted areas in which drilling has been done make any estimates of oil resources extremely speculative. Nevertheless, it is felt that the data given are justified, in the belief that the ideas of a geologist familiar with the region are better than those of a promoter. The oldest beds of interest to oil men are those of the Cretaceous, which are well developed in eastern Venezuela and about parts of Lake Mara-caibo. In both cases, a hard massive limestone is overlain by a great thickness, most of which is shale. In the west, in places this shale is more than 2000 ft. (610 m.) thick, while in the east it-mag attain 3500 ft. (1067 m.). The limestone and parts of the shale are oil producing. In the east, the Tertiary where present is almost entirely covered by the Quarternary, but in the west it is well developed. In probable unconformity over the Cretaceous shales is found a series of sandstones and shales, which may be called the lower coal series. It is well developed southwest of the lake, where it is the oil container, and is probably the lowest series exposed east of the lake. Above this is the Pauji shale, which is probably the point of origin of all the oil east of Lake Maracaibo and in the State of Falcon. It has a thickness of about 3000 ft. (914 m.) in the Mene Grande region. The upper coal series is developed as a great thickness of sands, shales, and clays, with some partly consolidated limestone. Its thickness may be as great as 10,000 ft. It is the oil container of the Falcon-El Mene region and a probable location for oil in some of the area about the lake. It may or may not include the so-called Maracaibo series in which the oil is found at Mene Grande. Over much of Venezuela, the Quarternary is present in unknown thickness, which probably is not great. It obscures oil structure in all cases and presents the greatest hazard of oil exploration for the fields which probably exist below.

Jan 1, 1923

By Ralph Arnold

While much geological work and drilling have been done in Venezuela, the incompleteness of geological evidence obtainable and the restricted areas in which drilling has been done make any estimates of oil resources extremely speculative. Nevertheless, it is felt that the data given are justified, in the belief that the ideas of a geologist familiar with the region are better than those of a promoter. The oldest beds of interest to oil men are those of the Cretaceous, which are well developed in eastern Venezuela and about parts of Lake Mara-caibo. In both cases, a hard massive limestone is overlain by a great thickness, most of which is shale. In the west, in places this shale is more than 2000 ft. (610 m.) thick, while in the east it-mag attain 3500 ft. (1067 m.). The limestone and parts of the shale are oil producing. In the east, the Tertiary where present is almost entirely covered by the Quarternary, but in the west it is well developed. In probable unconformity over the Cretaceous shales is found a series of sandstones and shales, which may be called the lower coal series. It is well developed southwest of the lake, where it is the oil container, and is probably the lowest series exposed east of the lake. Above this is the Pauji shale, which is probably the point of origin of all the oil east of Lake Maracaibo and in the State of Falcon. It has a thickness of about 3000 ft. (914 m.) in the Mene Grande region. The upper coal series is developed as a great thickness of sands, shales, and clays, with some partly consolidated limestone. Its thickness may be as great as 10,000 ft. It is the oil container of the Falcon-El Mene region and a probable location for oil in some of the area about the lake. It may or may not include the so-called Maracaibo series in which the oil is found at Mene Grande. Over much of Venezuela, the Quarternary is present in unknown thickness, which probably is not great. It obscures oil structure in all cases and presents the greatest hazard of oil exploration for the fields which probably exist below.

Jan 1, 1923

By William P. Blake

The occurrence and distribution of phosphorus is one of the most important questions with which the steel-maker has to do. Large sums are invested in processes for the removal of this element from ores before they come to the blast-furnace, and much greater sums in freeing the pig-iron from it. Mechanical engineers are becoming more and more critical of the amount of total phosphorus left in structural steel, the tendency being to require that it be reduced to the lowest possible figure. The old maximum of 0.1 per cent. is now considered much too high for first-class structural steel, and demands for 0.03 to 0.01 per cent. are by no means unheard of. The first to speak, in a scientific way, of the harmful effect of phosphorus on iron and steel appears to have been Meyer, who, in 1781, made mention of what we now term "cold-shortness," ascribing it to the presence of this metalloid, but not suggesting any remedy. It is, however, doubtful if a clear idea of this subject was possessed by the scientific world until after the invention of the pneumatic or Bessemer process, in 1855-56. One of the chief obstacles in the way of this renowned metallurgist,—one, indeed, the removal of which was the sine qua non of success,—was the phosphorus in the iron blown. The effect of the phosphorus does not seem to have been apprehended until many and costly experiments had been made, and then the required minimum percentage of it in the iron was secured only by the use of low-phosphorus ores. It was not until &apos;1879-80 that practical success was reached, by the Thomas process, in the actual removal of the phosphorus from the iron. We now know something of the effect of the total amount of phosphorus on iron and steel, but very little as to the effect of the condition of the phosphorus. The state of combination in which

Jan 1, 1893

By D. J. McAdam, R. W. Mebs

The technical cohesive strength of a metal means, not the interatomic forces, but the technically estimated resistance to fracture. An example of such resistance to fracture is the so-called "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture. According to the prevalent view,8 the technical cohesive strength of a metal. in any particular state as regards prior mecharlical treatment and heat-treatment, is determined by a limiting value of the algebraically greatest principal stress. In two previous papers by one of the authors, evidence was presented to indicate that the technical cohesive strength of a metal cannot be represented by a single stress value, but that it comprises an infinite number of values corresponding to the infinite number of possible combinations of the principal stresses. The technical cohesive strength thus comprises an infinite number of technical cohesion Limits, each representing a specific stress combination at fracture. In the same papers, evidence was presented that plastic extension causes a continuous increase in the technical cohesive strength. Such a variation is not in accordance with the prevalent view that plastic extension first increases, then decreases, the technical cohesive strength.&apos; In this paper, as in the previous papers,14.15 the algebraically greatest principal stress will be designated S1, the least principal stress will be designated 33, and the intermediate principal stress will be designated S². The technical cohesion limit under polarsymmetric tension (S1 = S2 = S3) will be termed the "disruptive stress," and the cohesion limit under unidirectional tension (S2 and S3 = o) will be termed the "severing stress."l4, .l5 The yield strength of a metal, according to the generally accepted theory, may be represented by a constant value of the shearing-strain energy, and hence by a constant value of the sum of the squares of the three principal stress differences. In the second of the previous papers,15 however, evidence was presented that the limiting yield stress decreases with increase in the volume stress, the algebraic average Of the three principal stresses.* This in fluence of the volume stress becomes prominent only in the field of triaxial tension. In the two previous papers,".&apos;5 diagrams were presented to show the variation of the technical cohesion limit, yield stress, and ultimate stress with the combination of principal stresses and with plastic extension. Those diagrams and the resultant • Any stress system ma? be resolved into a polarsymmetric stress causing pure volume strain and a combination of pure shearing stresses. which cause no change of volum

Jan 1, 1945

By Earl Hanson

FIRES in heavily timbered mines are disastrous, involving danger to both life and property. Some mines have been completely ruined or so heavily damaged that reopening them would not pay. Though few mines are entirely free from danger of fire, the risk is minimized by proper care and good design of plant. The Tintic Standard mine is at Dividend, Utah, in the famous Tintic mining district, about 60 miles south of Salt Lake City. The development of the mine was begun in 1907 by the late Mr. E. J. Raddatz and his associates. From the beginning, the work was hampered by high rock temperatures and the presence of high concentrations of rock gases such as carbon dioxide and nitrogen. Development work was carried on with great perseverance for nine years, and resulted in the discovery of ore in 1916. The total production of the Tintic Standard mine to Jan. 1, 1936, amounted to 1,664,388 tons of ore, having a gross value of .$61,996,719.

Jan 1, 1936

By W. E. Bruce, R. J. Morrell, James Paone

This chapter is a partial summary of an investigation by the U.S. Bureau of Mines (USBM) made in response to a recent request by the Assistant Secretary, Water and Power Development of the U.S. Department of the Interior, for a comprehensive review of horizontal boring technology related to underground power-line installation. This review is concerned primarily with 3 to 36-in. diam horizontal holes from several hundred to several thousand feet in length. An electric power system consists of three essential functions: generation, transmission, and distribution. The generation component includes the generating station and step-up substation; the transmission component includes the transmission line and stepdown substation at typical voltage levels ranging from 69 to 345 kv for underground lines and 69 to 500 kv for overhead transmission lines; the distribution component includes the distribution line carrying the commonly used voltages of 120, 208, and 240 v, the distribution transformer, and the line to the service customer.l The Federal Power Commission reports that 1600 miles of underground transmission lines of 60 to 345-kv capacity are now in service in the United States. By 1980, it is estimated that approximately 3000 miles of trans- mission lines will have to be placed underground.2 The cost of burying electric transmission lines underground in metropolitan areas, approximately 30 miles from the center of each of the most populated cities, will exceed $1.5 billion with the methods now available. The wide spread in unit costs of overhead and underground transmission lines narrows as right-of-way costs for overhead transmission in congested areas increase. Improved methods of underground emplacement will certainly reduce this difference in costs and even further favor underground emplacement. Also, in the future, overhead transmission lines will probably not be permitted in highly built-up areas.

Jan 1, 1970

By R. F. Hehemann, R. H. Goodenow

Thermal arrest, hot-stage microscopy, and transtnission electron microscopy techniques have been employed to study the transformations in low-carbon iron and Fe-9 pct Ni alloys. In continuous cooling experiments, each alloy transforms at an essentially constant temperature for cooling rates below the critical rate required for martensite formation. However, high-tenzperature transformation in pure iron takes place by a different mechanism than that in the 9 pct Ni alloys. Pure iron exhibits an equi-a a structure with a low and random dislocation density while the 9 pct Ni alloy exhibits a cell or lathlike substructure analogous to that of low-carbon martensite. This same substructure characterizes upper bainite in higher-carbon inaterials. UNTIL relatively recently, diffusionless transformations have been considered to take place by the same mechanism and have been termed mar-tensitic transformations.l-3 The most characteristic feature2 of this mode of transformation is the shape change produced by a shear deformation and growth of the product phase frequently occurs at an extremely high velocity approaching that of an elastic wave.4&apos;5 A different mechanism of diffusionless transformation was recognized first in Cu-Ga and other copper-base alloys.6,7 From the absence of surface tilting in these alloys, it has been concluded that transformation is not accomplished by the cooperative shear displacements that occur in mar-tensitic reactions. Transformation presumably takes place by the rapid movement of an incoherent interface which is capable of propagating across parent grain boundaries. Although the transformation is diffusionless in the macroscopic sense, advancement of these interfaces is accomplished by an atom by atom rearrangement. Transformations of this type therefore require thermal activation and are generally operative only at high temperature. Although requiring short-range diffusion at the interface, propagation still occurs so rapidly that the reaction cannot be suppressed with normal cooling rates.7 The resulting microstructures exhibit large, irregular-shaped regions of the product phase, which are essentially free of crystallographic features. Consequently, these reactions have been termed massive transformations. Transformation by the massive mechanism has been reported to occur in ferrous systems involving pure iron and binary alloys of iron with nickel, chromium, and silicon by Gilbert and owen.&apos; The Fe-Ni system is of special interest in that the massive transformation was observed in alloys with less than 15 pct Ni while alloys having more than about 28 pct Ni transformed by the conventional mar-tensitic mechanism. By employing cooling rates substantially higher than those used by Gilbert and Owen, Swanson and Parr have been able to suppress the massive transformation in alloys with 0 to 10 pct Ni9 and produce martensite as revealed by surface relief. The massive transformation in the alloys having less than 15 pct Ni was identified by the lack of surface relief and an irregular rather than clearly acicular microstructure.&apos; Speich and Swann, using thin-foil electron microscopy, identified three distinctly different structures10 in quenched binary Fe-Ni alloys. From 0 to 4 pct Ni the structure consisted of blocky grains of a with a low and random dislocation density. Alloys with 4 to 25 pct Ni exhibited a cell structure with a high dislocation density; and at greater than 25 pct Ni the structure consisted of internally twinned plates. The structural change at approximately 4 pct Ni suggests that alloys with low nickel content transform by a different mechanism than those with intermediate nickel contents and the transition from the cellular to the internally twinned structures at approximately 25 pct Ni is analogous to the transition from needles to internally twinned plates that occurs over a narrow range of carbon contents in Fe-C martensites.11,12 Conventional bainitic and martensitic modes of austenite decomposition operate in ternary Fe-C-Ni alloys having less than 10 pct Ni. This investigation was conducted in order to explore the conditions under which the massive, bainitic, and martensitic transformations occur and the relationships between these modes of decomposition.

Jan 1, 1965

By W. Jolley

Decarburized iron and Fe-3.28 pct Ni alloys were impact and tension tested in the temperature range of ambient to 4°K. It was found that alloying with nickel improves the fracture properties of the ferrite matrix. The improvement in toughness of iron alloyed with nickel is attributed to the effect of the nickel addition on the temperature and strain rate dependence of the yield stress as well as on slip behavior. The Fe-Ni alloy exhibits wavy slip when strained at temperatures down to at least 50°K. This behavior contrasts with that of the unalloyed iron where a change It is a generally accepted fact that of the common alloying elements of steel only nickel and manganese improve both the room-temperature yield strength and the notch impact properties. It has been argued for a number of years that manganese refines the ferrite grain size, the pearlite spacing, and the grain boundary carbides in medium- and low-carbon steels and thereby increases resistance to brittle fracture.&apos;&apos;&apos; This hypothesis recently was confirmed for a 0.04 pct C iron containing manganese, but at the same time from wavy to planar slip occurs at about 120°K. The observed lower temperature and strain rate dependence of the lower yield stress in the Fe-Ni alloy as compared to the unalloyed iron may be attributed to this difference in slip behavior. In contrast to suggestions published previously, transmission electron microscopy showed that the uniform dislocation distributions and the lack of dislocation tangles which are produced by low-temperature straining of bcc materials cannot be attributed to the absence of cross slip at these temperatures. no increase in notch toughness was observed in a decarburized Fe-Mn alloy.3 It thus appears that manganese only increases the toughness of Fe-Mn-C alloys by refining grain boundary carbides and has no toughening effect in carbon-free iron. On the other hand, the mechanism whereby nickel improves toughness has not been established. Hodge et a1.4 have clearly shown that a 3.28 pct Ni addition lowers the impact transition temperature of 0.02 pct C steel approximately 35°C when the grain size is maintained constant. Recently, Wullaert and Tetelman6 stated that nickel refined the grain boundary carbides of an Fe-C alloy and consequently increased the toughness. They also observed the previously reporteda-&apos;

Jan 1, 1969

LUTHER B. EAMES, Pueblo, Colo. (written discussion*).-In reading Mr. North&apos;s interesting paper, several points have been noted that appear to warrant discussion. With a feed all through 20 mesh, I feel inclined to question the use of steel balls as large as 2 in. in a tube mill. I have seen balls as small as-3/4 in. used for the dry grinding of cement clinker, and surely many more points of contact would result from smaller balls. This would seem to be desirable in a mill as short as 6 ft. The heavy load in the classifiers would also indicate a high proportion of returned pulp. I hope that some discussion by Mr. North -and others may develop this point. The flow sheet on page 1181 shows the solution returning from the dam valued at 40 c. per ton being added to the last decantation tank. Theoretically, this solution should not be added to that of a lower value. As I calculate it, if this solution were added to tank X the solution finally discharged from tank Z would be reduced in value by nearly 4 c. per ton.

Jan 10, 1919

By Enid C. Plante

INTRODUCTION To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), marcasite (FeS2), orpiment (As2S3), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also examined to determine if its behavior could be correlated with that of pyrite or marcasite (FeS2). EXPERIMENTAL METHOD Mineral for Flotation and Contact Tests Mineral was prepared in the manner already described&apos; and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and C02 free air bubbled through each suspension at a constant rate (about 1 bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation of oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.1 No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 FLOTATION OF "UNOXIDIZED" MINERALS WITH ETHYL XANTHATE AS COLLECTOR Fig I to 3, 4, 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox3 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C. Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1947

By E. Posnjak

IT is rather the general belief that acidified solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no. oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by, passing air for 3 hr. through solutions of Mohr&apos;s salt acidified with sulfuric acid." While this statement will be proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2. His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 1, 1927