Search Documents

By Rossiter W. Raymond

In the course of this address, President Raymond referred to the law, said to have been discovered at the French works of Terrenoire, that the amount of phosphorus may be increased without injury to steel, if the amount of carbon be proportionately decreased. The works named have been for more than a year, it is said, manufacturing in the open hearth, by the Martin process, steel rails containing as high as 0.35 per cent. of phosphorus, with about 0.15 per cent. of carbon, which were not found inferior to Bessemer rails. It is not claimed by the manager of the works that phosphorus is an ingredient to be preferred, or purposely introduced; but only that materials containing it (such as old iron rails, etc.), can be succesfully employed. Other parties have apparently a higher opinion still of the new manipulation, and are prepared to claim for " phosphorus steel" superior qualities. Mr. I. Lowthian Bell alluded to the subject in his recent address as President of the British Iron and Steel Institute, but without expressing a positive opinion. After pointing out that the commercial value of the process turned on the cheap manufacture of ferro-manganese, by means of which only could the necessary amount of manganese be introduced into the Martin bath, without increasing its contents of carbon, Mr. Raymond proceeded to say that the principle alleged to have been discovered at Terrenoire was already known years ago, in this country, at least. Not only had steel been manufactured here, containing high percentages of phosphorus, coupled with low percentages of carbon, and suitable for use in rails, boiler-plates, etc., but the reason of its surprising qualities had been distinctly surmised, if not widely proclaimed. The following analyses and extracts from private letters prove these assertions. Some of them assert a similar principle in .the case of wrought iron; but the analyses, and the remarks based upon them, have reference solely to the steel manufactured under the superintendence of Mr. Slade, at the works of the New Jersey Steel and Iron Company in Trenton.

By Rossiter W. Ph. D. Raymond

(From the President's Address at St. Louis, 1874.) IN the course of this address, President Raymond referred to the law, said to have been discovered at the French works of Terrenoire, that the amount of phosphorus may be increased without injury to steel, if the amount of carbon be proportionately decreased. The works named have been for more than a year, it is said, manufacturing in the open hearth, by the Martin process, steel rails containing as high as 0.35 per cent. of phosphorus, with about 0.15 per cent. of carbon, which were not found inferior to Bessemer rails. It is not claimed by the manager of the works that phosphorus is an ingredient to be preferred, or purposely introduced; but only that materials containing it (such as old iron rails, etc.), can be succesfully employed. Other parties have apparently a higher opinion still of the new manipulation, and are prepared to claim for "phosphorus steel" superior qualities. Mr. I. Lowthian Bell alluded to the subject in his recent address as President of the British Iron and Steel Institute, but without expressing a positive opinion. After pointing out that the commercial value of the process turned on the cheap manufacture of ferro-manganese, by means of which only could the necessary amount of manganese be introduced into the Martin bath, without increasing its contents of carbon, Mr. Raymond proceeded to say that the principle alleged to have been discovered at Terrenoire was already known years ago, in this country, at least. Not only had steel been manufactured here, containing high percentages of phosphorus, coupled with low percentages of carbon, and suitable for use in rails, boiler-plates, etc., but the reason of its surprising qualities had been distinctly surmised, if not widely proclaimed. The following analyses and extracts from private letters prove these assertions. Some of them assert a similar principle in -the case of wrought iron ; but the analyses, and the remarks based upon them, have reference solely to the steel manufactured under the superintendence of Mr. Slade, at the works of the New Jersey Steel and Iron Company in Trenton.

Jan 1, 1875

By John W. Padan, John E. Crawford

Beginning with a small but positive participation in undersea mining, the Bureau of Mines continues its active investigations into this potentially tremendous field. The Bureau began its active role in undersea mining in September 1963, with a small task force of three dedicated scientists and a secretary, establishing headquarters at the old Tiburon Naval Net Depot about seven miles up the coast from San Francisco. The past months have been both busy and productive. With 22 Federal agencies involved in oceanography, it logically was the intent of Congress that the Bureau of Mines undertake research concerned only with the technology of marine mineral production and utilization. The Bureau has maintained this purpose in its activities at Tiburon, for while institutes, universities, the Navy and other Government agencies have developed exceptional programs in the fundamental science of the oceans, commonly called oceanographic research, little has been done toward advancing man's ability to exploit the ocean floors other than by drilling for oil and gas and sulfur.

Jan 3, 1965

By E. N. Cameron

Graphite has been included in U. S. lists of strategic minerals since the problem of mineral deficiencies was revealed during World War I. Since 1918 the domestic graphite industry has led a precarious existence, and there has been much uncertainty as to the amounts of usable graphite of various grades that would be available from domestic sources in time of emergency. In 1950-1951 therefore, the writer, assisted by Paul L. Weis, undertook a review of domestic graphite sources for the U. S. Geological Survey. The conclusions of this study are presented here, with a discussion of some technologic and politico-economic factors bearing upon the problem. Uses of Graphite: Natural graphite as marketed exhibits a wide range of properties, which determine the uses to which it is put. The most essential uses are in the manufacture of crucibles and related refractory articles, in lubricants and packing materials, and in the manufacture of batteries, foundry facings, pencils, and carbon brushes. Numerous specifications covering the mineral in its various applications must be met by producers and processors of graphite. The problem of supply is therefore not simply one of procuring a sufficient total tonnage, but the more difficult problem of procuring enough of each different grade to meet foreseeable needs.

Oct 1, 1956

By H. R. Stahl

THE disseminated lead district of Southeast Missouri lies 70 miles south of St. Louis. The only metal of economic importance in the ore is lead, but minor amounts occur of iron, zinc, copper, cobalt, nickel, silver and cadmium. These minor metals, as might be expected, tend to concentrate in both the flotation and table middlings. In the past, some zinc has been recovered by differential flotation. The silver and cadmium tend to associate with the zinc, and some recovery is made of these two metals at the smelter. The lead occurs as galena, or lead sulphide. The minor metals are also present as sulphides. The presence of oxidized lead is suspected, but has not been definitely proved. The gangue is chiefly dolomitic limestone, with small amounts of sandstone and shaly glauconitic and chloritic minerals. The ore contains about 3.25 per cent lead, occurring as galena disseminated through the gangue. Some of the galena is very finely disseminated, and the mineral in the gravity tailings, or chat, is seldom or never in the free state. The method of treatment of the ore has been evolved over a period of 75 years; hence probably is not far from correct. The milling processes have tended toward simplification during the past 15 years, but recoveries have never been sacrificed for the sake of simplicity. In many cases, simplification of flowsheets has led to better recoveries and operating economies. A simplified flowsheet is shown in Fig. I. The St. Joseph Lead Co. operates four mills in the Flat River district, with a normal total capacity of about 21,000 tons per day, divided as follows: Federal mill, 11,000 tons; Leadwood mill, 4500 tons; Desloge mill, 3400 tons and Bonne Terre mill 2400 tons. The methods of concentration used at these plants are similar in principle; they differ mainly in details and in the type and size of the equipment used. The process of concentration may be divided into five main steps; i.e., dry crushing, wet grinding, classification with its attendant desliming, tabling and flotation. A brief description of these processes will be given, noting important differences in the various plants, and also noting the more important changes or developments of the past few years. DRY CRUSHING The run-of-mine ore is hoisted in skips, the capacity of these skips ranging from 2 ¾ tons to 8 ¼ tons. At the Desloge plant, the ore is hoisted in 2-ton mine cars on self-dumping cages. All ore is hoisted at shafts adjacent to the various crushing plants, no ore being transported on the surface. Primary breaking at all the mills is accomplished with 9E Telsmith breakers. Preliminary screening is provided ahead of most of these crushers, either by station-

Jan 1, 1943

By Harold E. Thomas, Samuel S. M. Chan, Nicholas Bada

The U.S. Bureau of Mines has developed a technique for locating and evaluating bedding plane cracks in mine roof by an air-injection and hot-film flow logging technique. It is ultrasensitive to cracks and is especially useful for detecting the early stage of crack development. Potential applications include: (1) correlation with roof sag measurements, (2) locating cracks for grouting, (3) comparison of mechanical and resin roof bolt effectiveness, and (4) possible delineation of the fracture zone to confirm the arch hypothesis. The required equipment is inexpensive and simple to operate.

Jan 1, 1975

By F. W. Osterwald, C. R. Dunrud

Coal mine bumps are a serious hazard to life and property in the mines of east-central Utah. Research into geologic factors associated with these bumps indicates that the bumps are spatially and genetically related to structural and stratigraphic features. Some bumps are directly related to stress accumulation along faults, either from natural causes or as a result of mining. Frictional properties of bedding planes between coal and roof rock, and between some rock units within the roof, directly affect the deformation of coal ribs, and hence the incidence of bumps. These frictional properties are related to the lithology of the roof rocks as well as to the sedimentary structures within the rocks. Commonly a sequence consisting of 1/3 ft of carbonaceous silt-stone, about 2/3 ft of rider coal, and several ft of massive siltstone or sandstone overlies the main seam. The sequence causes difficult roof conditions in the mines, difficult mining conditions and, directly or indirectly, many bumps. The U. S. Geological Survey has studied the relationships between geological features and coal mine bumps at Sunnyside, Utah, for about six years. The work, which was originally undertaken at the request of and in cooperation with the U.S. Bureau of

Jan 1, 1965

Reply to discussion of the paper of C. W. Washburne, presented at the New York meeting, February, 1914 (Trans., xlviii, 687 to 694 (1914)). C. W. WASHBURNE, New York, N. Y. (communication to the Secretary*).-Professor Lane makes an interesting contribution to the study. of chloride waters, in saying that calcium chloride waters occur not only in the greenstones of the Lake Superior copper mines, but also in the interbedded -felsitic conglomerates and "in far-removed sandstones, e.g., near Whitefish lake, and Ontonagon, in the Michigan iron mines, and in the Storm King granite." Surely these are not connate waters preserved from the Algonkian sea, assuming that the Algonkian sediments are marine rather than continental. Finding the same type of water in the Storm King granite points rather toward an abyssal source. The possible connection of these waters with the magma of the greenstone is immaterial, although some basic calcic magma is the most probable source. It is to be expected that the ascending water of the region would be found not only in the greenstones, but in all the rocks which it could penetrate. The ascent of water of this kind along vertical passages, and the consequent addition of a common ion: to the circulating sedimentary salt solutions, would explain the precipitation and localization of the "giant, concretionary" salt plugs of the Gulf Coast, without making the ex-excessive demand for an improbable quantity of salt in the adjacent sediments that is required by the unmodified theory of Harris. With-out such a precipitating medium most of the dissolved sodium chloride would have been lost by passing on to the surface without precipitation. The base to which the chlorine ions were attached is immaterial, providing they were sufficiently concentrated, but the presence of the chlorides of calcium and magnesium in the solutions is indicated by the associated bodies of secondary dolomite.

Jan 4, 1915

By R. W. Raymond

THE death of Privy Councilor Bruno Kerl, on March 25, 1905, terminated a distinguished and useful career. Bruno Kerl was born March 24, 1824, at St. Andreasberg in the Harz, and entered in 1840 the mining school of Clausthal, where he studied for three years, working at the same time in the mines and stamp-mills. After an additional year of practice in the silver-reduction and iron-works of the Upper Harz, he passed his examination as a metallurgical graduate, and studied for a year at Göttingen under WV filer in chemistry, Hausmann in mineralogy, and eminent teachers in other branches. In 1846 he was employed at the Oker works, but very soon left this post, to become a tutor in chemistry, metallurgy, etc., at Clausthal, where he continued to labor until 1867. During this period the Clausthal school became a completely equipped Mining Academy, and Kerl was made in 1862 a full professor. Meanwhile, in addition to the work of instruction, he discharged, simultaneously or successively, the duties of many responsible official positions in the Royal Hanoverian administration of mines and smelting-works, and also published many valuable books and treatises. Among these were professional guide-books to the Upper and Lower Harz, and their characteristic metallurgical processes; a manual of qualitative and quantitative blow-pipe analysis; another of metallurgical assaying ; and, most important of all, a Handbook of Metallurgy in four volumes, the second edition of which was issued in Leipzig, 1861-1865. This book was speedily recognized as the leading authority in its field. In this country, the English translation and revision, by Crookes and Röhrig, published about 1869, had a large circulation. In addition to these literary labors, Prof. Kerl became in

Jul 1, 1905

By W. M. Weigel

The general term "sand" applies to a multitude of similar materials consisting of fine granular mineral. As usually understood, it means the ordinary natural product used for structural purposes and made up largely of grains of quartz. Quartz sand constitutes by far the greater bulk of the production, but there are other grades used for industrial purposes, such as molding sand, glass sand and many others, that may be grouped under the general name of special sands. Under this general group would fall filter sand, sand-blast sand, engine sand, potter's sand, abrasive sands of all kinds, sand for pulverizing, roofing sand, flooring sand, fire or furnace sand, standard sand, burnishing sand, sand for magnesium oxychloride cement-plasters and sand for chemical and metallurgical purposes. Sources of Supply Sand is a widely distributed natural product and even the better grades are low-priced commodities. For these reasons development has occurred near points of consumption where sand meeting the requirements is available. Some special grades, however, cannot be prepared from any sand bed and shipments are often made over considerable distances when the only developed deposit is remote from the consuming center. This is true of filter sand, sand-blast sand, sand for pulverizing and some of the others when chemical purity or grain size, coupled with the need of a properly equipped plant for preparation, are required. New Jersey is a large producer of filter, engine, sand-blast, fire, and pulverizing sand. Pennsylvania, and West Virginia produce special sands for pulverizing, fire sand, abrasive sand, engine sand and sand for chemical and metallurgical use. Ohio produces much sand-blast, fire and abrasive sand, and some filter sand. Illinois and Minnesota produce

Jan 1, 1926

By Tracy C. Jarrett

In 14-karat gold alloys, as in 10-karat gold alloys,3 the addition of such metals as zinc, nickel, copper and silver produces a wide range of physical and chemical properties such as color, hardness, corrosion resistance and melting points. These important factors made gold alloys desirable in the optical work and for jewelry. In 14-karat gold alloys, as well as in 10-karat or 12-karat, it is possible to have two golds of the same color, one of which will corrode more than the other, although it may be harder. Some of these alloys have been investigated by F. E. Carter,' E. M. Wise,= and L. Sterner Rainer.4 In this group of alloys the gold content of 58.3 per cent (14-karat) was held constant, while the copper varied from 36 to 24 per cent. The balance of the alloy consisted of one, two, or three of the metals silver, zinc, and nickel. All the alloys were melted in an induction furnace and cast into an ingot that measured 3 by 1/4 by 3/4 in. The method of determining the melting points, color determinations and acid test have been discussed in previous papers by the author.2, 3 It is necessary to use small test bars (Fig. I). The tensile bars were annealed at 1300oF. for 20 min. and then air-cooled. There being a very marked drop when the yield point was reached, "the drop of the beam" method was used in determining the yield point. Alloys Gold-copper.zilzc A~loys.—Gold-copper-zinc alloys melt, cast, and labricate easily. The low melting points, however, limit their use to some extent. The physical properties of these alloys are not entirely satisfactory. When the ultimate strength is satisfactory, the elongation and reduction of area are too low (Table I). Gold-copper-sinr-nickel A lloys.—In this group of alloys, in which zinc and nickel replace copper in approximately equal parts (Table I), the yield point, hardness, and ultimate strength increase with the increase of zinc and nickel content, while the reduction of area and elongation decrease. The physical properties are desirable, particularly of the white gold alloys. The alloys of this group are not difficult to cast and fabricate, and most of these colors could be used commercially. Gold-copper-nickel A lloys.—Gold-copper-nickel alloys are similar to the gold-copper-zinc and the gold-copper-zinc-nickel alloys. They do, however, possess high yield point, ultimate strength and hardness, somewhat higher than those of the other two groups mentioned (Table I). The difficulty with these alloys is that they fire-crack readily and heavy rolling is necessary between annealings. Being hard to fabricate, many

Jan 1, 1941

By Tracy C. Jarrett

In 14-karat gold alloys, as in 10-karat gold alloys,3 the addition of such metals as zinc, nickel, copper and silver produces a wide range of physical and chemical properties such as color, hardness, corrosion resistance and melting points. These important factors made gold alloys desirable in the optical work and for jewelry. In 14-karat gold alloys, as well as in 10-karat or 12-karat, it is possible to have two golds of the same color, one of which will corrode more than the other, although it may be harder. Some of these alloys have been investigated by F. E. Carter,' E. M. Wise,= and L. Sterner Rainer.4 In this group of alloys the gold content of 58.3 per cent (14-karat) was held constant, while the copper varied from 36 to 24 per cent. The balance of the alloy consisted of one, two, or three of the metals silver, zinc, and nickel. All the alloys were melted in an induction furnace and cast into an ingot that measured 3 by 1/4 by 3/4 in. The method of determining the melting points, color determinations and acid test have been discussed in previous papers by the author.2, 3 It is necessary to use small test bars (Fig. I). The tensile bars were annealed at 1300oF. for 20 min. and then air-cooled. There being a very marked drop when the yield point was reached, "the drop of the beam" method was used in determining the yield point. Alloys Gold-copper.zilzc A~loys.—Gold-copper-zinc alloys melt, cast, and labricate easily. The low melting points, however, limit their use to some extent. The physical properties of these alloys are not entirely satisfactory. When the ultimate strength is satisfactory, the elongation and reduction of area are too low (Table I). Gold-copper-sinr-nickel A lloys.—In this group of alloys, in which zinc and nickel replace copper in approximately equal parts (Table I), the yield point, hardness, and ultimate strength increase with the increase of zinc and nickel content, while the reduction of area and elongation decrease. The physical properties are desirable, particularly of the white gold alloys. The alloys of this group are not difficult to cast and fabricate, and most of these colors could be used commercially. Gold-copper-nickel A lloys.—Gold-copper-nickel alloys are similar to the gold-copper-zinc and the gold-copper-zinc-nickel alloys. They do, however, possess high yield point, ultimate strength and hardness, somewhat higher than those of the other two groups mentioned (Table I). The difficulty with these alloys is that they fire-crack readily and heavy rolling is necessary between annealings. Being hard to fabricate, many

Jan 1, 1941

By F. Weinberg, E. H. McLaren

Dilute binary alloys have been solidified under controlled thermal conditions, and solute distributions, temperatures during freezing and melting, and the position and morphology of the solid-liquid interfaces have been examined. Binary Zn, Sn, and Pb based alloys were investigated with solute additions of AgU°, AU°, Sb'24, TlZo4, snH3, and Zns5. Approximately 150 cc of metal was used in each ingot. Appreciable solute segregation occurred in most of the ingots, depending on the solute concentrations, distribution coefficients. and freezing conditions of the alloys. Measurements were made of the general solute distribution by sectioning layers of material from the ingot circumference and counting the activity of each layer. Local segregation was detected by autoradiographic techniques. Freezing and melting curves for the same alloys were obtained by precision resistance thermometry. These curves are related to the corresponding measured solute distribution curves and those calculated from theoretical expressions. The position and morphology of solid-liquid interfaces during freezing were determined by both decanting and quenching techniques. The results indicate the manner in which freezing and remelting occurred under the conditions investigated. If an isomorphous dilute binary alloy is solidified or melted under equilibrium conditions, the concentration of solute in both solid and liquid would be uniform at all stages in the freezing process. The solute concentrations during freezing could be determined from the phase diagram of the alloy, and the freezing curves would have an alloy slope defined by the solidus and liquidus points. In practice, however, solidification under equilibrium conditions rarely, if ever, occurs, primarily because of low rates of diffusion in the solid and incomplete mixing in the liquid. As a result, the solute distribution and the shape of the freezing and melting curves obtained in a given system depends on a number of factors. These include, in addition to the extent of diffusion and mixing, the initial solute distribution and concentration, the distribution coefficient, the rate of freezing or melting, supercooling of the liquid, the morphology of the solid-liquid interface, and the effect of annealing. The purpose of the present investigation was to determine, experimentally, actual solute distributions and thermal curves for a series of dilute binary alloys, using tracer techniques to determine the solute distributions and precision resistance thermometry for the temperature measurements. In addition, observations were made of the positions and morphologies of the solid-liquid interfaces during freezing and remelting. The distribution of solute in a dilute alloy, assuming complete mixing in the liquid, and negligible diffusion in the solid, is given by1 where Co is the mean solute concentration of the alloy, C, is the solute concentration in the solidg is the fraction of the ingot solidified, and ko is the equilibrium solute distribution coefficient (assumed to be independent of concentration for dilute alloys). For the case of partial mixing, ko can be replaced by an effective distribution coefficient k. If solute transport in the liquid is assumed to be entirely due to diffusion, with negligible diffusion in the solid, then the solute distribution in the solid is given by Tiller et a1.' as where R is the rate of advance of the solid-liquid interface, D is the solute diffusion coefficient in the liquid, and x is the position of the interface from the start of freezing. The temperature at the interface TI is related to the solute concentration of the solid at the interface C, by the expression where Tm is the freezing temperature of the pure solvent and ml is the slope of the liquidus for the binary alloy being considered. Accordingly, by relating TL to the actual temperatures measured in the present experiments, solute distributions can be deduced from the temperature measurements. Using the above expressions, the measured solute distribution of a given alloy may be compared to the theoretical distributions, as well as to the distribution calculated from the observed freezing curve. EXPERIMENTAL The solvent materials used in making up the binary alloys were C. P. New Jersey zinc (99.999 pct), Vulcan Extra Pure Tin (99.999 pet), and Tadanac lead (99.998 pct). The solute elements were of 99.99 pct purity or better, and were activated in the

Jan 1, 1963

By G. L. Simard, D. J. Salley, J. Chupak

DITHIOPHOSPHATES and xanthates are the principal collectors for sulphide minerals, and consequently any knowledge of mineral-collector systems of this type is of value. In the present investigation an attempt was made to obtain information on the interaction of a typical dithiophosphate with galena. In carrying out this study, radioiso-topes, so much discussed in the past few years,', ' were extensively employed. By using radioactive dithiophosphate synthesized from radioactive phosphorus, a rapid and sensitive analytical procedure G. L. SIMARD is in the Research Division, Stamford Research Labs., American Cyanamid Co., Stamford, Conn.; J. CHUPAK, formerly in the Research Division, Stamford Research Labs., is now at Camp Detrick, Frederick, Md.; and D. J. SALLEY is in the Research Division, Stamford Research Labs. AlME New York Meeting, Feb. 1950. TP 2815 B. Discussion (2 copies) may be sent to Transactions AlME before April 30, 1950. Manuscript received Oct. 17, 1949. was at hand. This permitted determination of such important quantities as the rate of uptake of dithiophosphate by the mineral, the amount existing at equilibrium on the mineral surface and in the solution, and the desorption of the agent from the surface. Such measurements were possible even on single crystals of galena. In addition the exchange of dithiophosphate between the solution and the sorbed phase was examined, a matter which could be accomplished only by the use of isotopes. It is desired to point out at this time that throughout this paper the term "sorption" has been employed to designate the uptake of agent by mineral, without implication as to the nature of the process by which the uptake was accomplished. Experimental Materials: Galena: The galena was from the Tri-State district. For studies on ground mineral four preparations were used during the course of the investigation. These were prepared from selected large crystals by wet grinding in order to reduce surface oxidation. Alcohol was chosen as a convenient medium for this purpose. The ground mineral was then fractionated by sedimentation in alcohol, dried by evacuation, and stored in a nitrogen-filled desiccator. Data on the preparations are tabulated in table I. The size analysis indicated that the areas of the preparations were of comparable magnitude, even though the absolute values may be somewhat incorrect. Dithiophosphates: Nonradioactive dithiophbsphate (di-isopropyl or di-secondary butyl) was obtained by purification of a commercial product. An aqueous acid solution of the agent was extracted with petroleum ether, the ether layer dried, and the dithiophosphate precipitated as ammonium salt with anhydrous ammonia. Several repetitions of this process resulted in a nearly colorless, flaky product of good purity. (General formula (RO,)PSSNH,). Radioactive dithiophosphate was synthesized by heating radioactive elementary red phosphorus* • For early experiments (1943 to 1944), the elementary red phosphorus was obtained from the cyclotron group at the Crocker Radiation Laboratory of the University of California. Berkeley, through the courtesy of Dr. Joseph W. Hamilton. For more recent work (1946 to 1949). the elementary radioactive Phosphorus has been supplied by the Oak Ridge National Labarotories on allocation from the U. S. Atomic Energy Commission. with sulphur at 270" to 300°C to produce radioactive P,S,. The latter was then treated with the desired purified alcohol (isopropyl or secondary butyl) at 60" to 80°C to form the dithiophosphoric acid derivative. Purification was effected in the same manner as for the nonradioactive material. The effectiveness of the purification method was established by the isotopic dilution method." The same technique was used to show that only negligible decomposition of neutral or of carbonate solutions of the dithiophosphate took place over a period of a day; this was true whether or not galena was suspended in the solutions. Procedures: Radioactivity: The activity of a solution was obtained by counting with a small glass-jacketed, silvered Geiger counter, using a conventional scaling circuit.' Crystals and other solids were counted under a bell-shaped, mica-window counter tube. Sufficient counts were made so that the probable error of counting was of the order of +I-3 pct. The specific activity in terms of counts per minute

Jan 1, 1951

By J. Chupak, D. J. Salley, G. L. Simard

DITHIOPHOSPHATES and xanthates are the principal collectors for sulphide minerals, and consequently any knowledge of mineral-collector systems of this type is of value. In the present investigation an attempt was made to obtain information on the interaction of a typical dithiophosphate with galena. In carrying out this study, radioiso-topes, so much discussed in the past few years,', ' were extensively employed. By using radioactive dithiophosphate synthesized from radioactive phosphorus, a rapid and sensitive analytical procedure G. L. SIMARD is in the Research Division, Stamford Research Labs., American Cyanamid Co., Stamford, Conn.; J. CHUPAK, formerly in the Research Division, Stamford Research Labs., is now at Camp Detrick, Frederick, Md.; and D. J. SALLEY is in the Research Division, Stamford Research Labs. AlME New York Meeting, Feb. 1950. TP 2815 B. Discussion (2 copies) may be sent to Transactions AlME before April 30, 1950. Manuscript received Oct. 17, 1949. was at hand. This permitted determination of such important quantities as the rate of uptake of dithiophosphate by the mineral, the amount existing at equilibrium on the mineral surface and in the solution, and the desorption of the agent from the surface. Such measurements were possible even on single crystals of galena. In addition the exchange of dithiophosphate between the solution and the sorbed phase was examined, a matter which could be accomplished only by the use of isotopes. It is desired to point out at this time that throughout this paper the term "sorption" has been employed to designate the uptake of agent by mineral, without implication as to the nature of the process by which the uptake was accomplished. Experimental Materials: Galena: The galena was from the Tri-State district. For studies on ground mineral four preparations were used during the course of the investigation. These were prepared from selected large crystals by wet grinding in order to reduce surface oxidation. Alcohol was chosen as a convenient medium for this purpose. The ground mineral was then fractionated by sedimentation in alcohol, dried by evacuation, and stored in a nitrogen-filled desiccator. Data on the preparations are tabulated in table I. The size analysis indicated that the areas of the preparations were of comparable magnitude, even though the absolute values may be somewhat incorrect. Dithiophosphates: Nonradioactive dithiophbsphate (di-isopropyl or di-secondary butyl) was obtained by purification of a commercial product. An aqueous acid solution of the agent was extracted with petroleum ether, the ether layer dried, and the dithiophosphate precipitated as ammonium salt with anhydrous ammonia. Several repetitions of this process resulted in a nearly colorless, flaky product of good purity. (General formula (RO,)PSSNH,). Radioactive dithiophosphate was synthesized by heating radioactive elementary red phosphorus* • For early experiments (1943 to 1944), the elementary red phosphorus was obtained from the cyclotron group at the Crocker Radiation Laboratory of the University of California. Berkeley, through the courtesy of Dr. Joseph W. Hamilton. For more recent work (1946 to 1949). the elementary radioactive Phosphorus has been supplied by the Oak Ridge National Labarotories on allocation from the U. S. Atomic Energy Commission. with sulphur at 270" to 300°C to produce radioactive P,S,. The latter was then treated with the desired purified alcohol (isopropyl or secondary butyl) at 60" to 80°C to form the dithiophosphoric acid derivative. Purification was effected in the same manner as for the nonradioactive material. The effectiveness of the purification method was established by the isotopic dilution method." The same technique was used to show that only negligible decomposition of neutral or of carbonate solutions of the dithiophosphate took place over a period of a day; this was true whether or not galena was suspended in the solutions. Procedures: Radioactivity: The activity of a solution was obtained by counting with a small glass-jacketed, silvered Geiger counter, using a conventional scaling circuit.' Crystals and other solids were counted under a bell-shaped, mica-window counter tube. Sufficient counts were made so that the probable error of counting was of the order of +I-3 pct. The specific activity in terms of counts per minute

Jan 1, 1951

By James Gardner

IN 1923, Oklahoma took second place as an oil-producing state; whereas in 1922 it was the leader. California surpassed it, in 1923, by nearly 100,000,000 bbl. In 1923, Oklahoma produced, according to statistics of The Oil & Gas Journal, 165,013,685 bbl., or an increase of approximately 10 per cent. over the preceding year; the increase in California was approximately 90 per cent. The number of wells drilled in Oklahoma and the results of the two years are contrasted in the following table from data published in a preliminary bulletin by the U. S. Geological Survey. 1922 1923 Oil wells 4,149,68%. 3,515, 60% Gas wells 571, 9 %u 587, 11% Dry holes 1,428,23% 1,731,29% Total wells 6,148 5,833 The initial production from wells drilled in Oklahoma in 1923, according to The Oil & Gas Journal, was the largest in the history of the state, being 1,277,936 bbl. It has been 32 years since oil development began in the state, last year being the largest in the amount of production. The production of the past year would have been considerably greater were it not for the shutdown order in the Burbank field and curtailment of production in the Hewitt and Tonkawa pools.

Jan 3, 1924

By WALTER M. DAKE

WITH the renewal of the contract between bituminous miners and operators, whereby a period of three years is assured without the devastating effect of irregularity of operation due to general strikes; and, with the increasing comprehension on the part of the large consumers as to the stabilizing effect of adequate storage upon prices; the coal industry has reached that period of its history in which permanence of purpose towards necessary changes is being crystallized, and these changes accomplished by the industry. It is to be hoped that during this era the phrase- " Our National Coal Problem "-will be relegated to the limbo of' antiquated expressions. That this epoch is upon us is evinced by the fact that operators are turning to consolidations, whereby financially sound companies will acquire smaller production units and place themselves in position to maintain constant supervision and control of their development and output; and, as further proof of the arrival of these changes, may be cited the entrance of additional members of the engineering profession into the many phases of management and operation, where- by the cost per ton of output will be, constantly reduced through the increasing use of modern methods and equipment. As an instance, attention is specifically called to the developments in mechanical loading, proposed and actual continuous underground transportation systems and betterment in methods of preparation.

Jan 1, 1924

By David W. Brunton

Mine-drainage and the ever-increasing demand for water on the plains have within the past few years necessitated the driving of a great number of adits and tunnels, including many of considerable size and great length. In most instances, existing conditions have called for extreme rapidity of execution; and this necessity, coupled with the high altitudes at which most of the work has been carried on, excessive freight-rates, and difficulty of access, has involved many complex and interesting problems. One of the most rapidly executed undertakings of this class is the Laramie tunnel, recently completed for the Laramie-Poudre Reservoirs & Irrigation Co. This tunnel is driven through Green ridge, a spur of the Continental Divide, which separates the Laramie river from the Cache-la-Poudre in Laramie county, Colo. Green ridge is extremely persistent, and further northward in Wyoming is known as Sherman hill, the highest point on the Union Pacific railway. At the point where the tunnel is driven, two opposing bends bring these streams within 2.5 miles of each other, with a difference in elevation of 500 ft. The rock exposed on the banks of the two rivers does not differ materially in hardness; and, without a geological study of the conditions involved, it would appear that the difference in the depth of erosion of the two streams is due principally to the greater volume of water at this point in the Cache-la-Poudre, which has a drainage-area above the tunnel-portal of 110 sq. miles, as against 30 sq. miles of natural drainage for the Laramie. To increase the water-supply at the tunnel, however, this latter amount has been augmented by two side collection-canals, which bring the available drainage-area up to 84 square miles. The nearest railroad shipping-point to the eastern portal is

Jan 1, 1913

By E. C. Dominguez, H. B. Scharf

THE Sparrows Point plant of Bethlehem Steel Co., southeast of Baltimore, is the largest Bethlehem plant, with an annual rated capacity of 6.2 million ingot tons. There is considerable diversity of product, but a high percentage is sheet, tin plate, galvanized sheets, and rod and wire. The large amount of light-weight end product requires a number of pickling installations that necessarily consume large quantities of sulfuric acid. In the coking operations sulfuric acid is also consumed in recovery of ammonia as ammonium sulfate and in treatment of recovered light oil derivatives. Total sulfuric acid consumption in the plant is currently approaching 10,000 tons per month, of which 55 to 60 pct is required for pickling. In 1951 the acute sulfur shortage caused grave concern as to future sulfuric acid supply for the Sparrows Point plant. Raw materials for acid making were already at hand in the form of hydrogen sulfide and pyrites sufficient to produce nearly half the sulfuric acid required at that time. It was also known that the Bethlehem mining activities would produce additional pyrites in the future. Late in 1951 Bethlehem management decided to build a 250-ton sulfuric acid plant at Sparrows Point to utilize these raw materials. The plant was built and put in operation in May 1953. The steel plant has expanded considerably since 1951, and it is now necessary to operate the acid plant far over rated capacity in order to supply plant demand. Production of acid in 1954 amounted to 93,000 tons. Raw Materials for Acid Making: Coking operations at Sparrows Point produce a residual fuel gas in large quantity which has a net heating value of 525 to 545 Btu. Prior to 1950, plant surplus coke oven gas was sold to the local utility company. In

Jan 1, 1957

By G. L. Coleman, D. S. Hutton, W. C. Leslie

The occurrence of twins in a iron, generated during cooling through the ?-a transformation, is well established,1-8 but this phenomenon has been nearly ignored during the past 20 years. It is the purpose of this note to call attention to the prevalence of such twins and to illustrate their appearance. The work of paxton7 and Kelly8 has demonstrated beyond reasonable doubt that for Neumann bands (mechanical twins) in a iron the twinning plane is (112) and the twinning direction <III>. The agreement with McKeehan&apos;s earlier work4 on transformation twins indicates that both types of twins in ferrite follow the same twinning law. There is little doubt of this conclusion, but it could be strengthened by a microbeam X-ray determination of the orientation relationship between a single ferrite grain and a transformation twin within that grain, as in the technique used by Kelly8 on Neumann bands. RESULTS AND DISCUSSION Transformation twins, identified by their appearance on a polished and etched section, were found in

Jan 1, 1960