Search Documents

By J. Douglas Gibson

In Canada, the economic climate for mining is still warm, but a noticeable chill set in last November when the Government published a White Paper on tax reform known as the Carter Report. Moreover, this chill could drop to a freeze injurious to the whole Canadian economy if two of the proposals in the Carter Report are adopted. The offending suggestions call for an end to (1) the depletion allowance and (2) the three-year tax holiday for new mines. Both of these tax incentives have played a major role in the postwar development of the Canadian economy and will, if undisturbed, play an even more important role in the future. The fact that they have worked and worked well is evident from the record. Fruits of an Industrial Beanstalk Excluding fuels, the value of Canadian mineral production was just under $3 billion in 1968-almost nine times as much as in 1946. With fuels included, the figure is $4.25 billion, or almost ten times as much as in 1946. Proportionately, this growth far exceeds that of Canada's manufacturers or of her economy as a whole. Table I traces the overall mineral production growth by principal products. Of particular interest here are petroleum, iron ore, natural gas, sulfur and potash, the combined production of which has grown from little or nil to a point where it now accounts for more than 40% of Canada's mineral output.

Jan 1, 1970

By John Reynders

Our entry into the World War suddenly brought home to us in a startling way the vital importance of manganese. Since the war, much has been written and said upon the subject of manganese and a great deal of time and money have been spent in attempts to find an adequate substitute for this metal in the manufacture of steel; none has been found. It is true that ways are known by which it is possible to make small amounts of good steel without manganese; but taking into consideration the diminishing quality of iron ores and fuels. as' well as the increasing exaction of specifications for finished products, it may safely be assumed that high-grade manganese ore will be more and. more a necessity in the production of steel as time goes on. Taking world resources as a whole it may be well to point out that the problem of obtaining needed supplies of manganese from a strictly commercial viewpoint is now less serious than it was before the war. Formerly it was feared that world resources of high-grade manganese ore might be exhausted in a relatively short time, but, largely as a result of the stress laid upon the importance of manganese during the war, the world's available supply of high-grade manganese ore has been greatly augmented by new discoveries and fuller development of previously known deposits.

Jan 5, 1927

By M. J. Sinnott, J. C. Tobin

A technique for collecting and analyzing the small quantities of gases desorbed on heating metal powders has been developed. The gases collected from copper powders of various types of manufacture have been analyzed and found to contain H2O, CO2, and SO2. The quantities of gas evolved vary from 0.05 to 1.0 milliliter, under standard con-ditons of temperature and pressure, per gram of powder. The source of the gas has been traced to surface films on the powder. IN the powder-metal industry it is recognized that the presence of gases in the powders affects the processing and resulting properties of the sintered product. Several sources for these gases are possible; namely, chemical reactions with the sintering atmospheres, inclusion. of gases during compacting, dissolved gases in the metal powder, and sorbed gases on the metal-,powder surfaces.1, 2, 3 Since the quantities of the gases are relatively small, no direct attempt has been made to collect and analyze them nor to isolate their source. The work that has been done has been concerned with the dimensional stability of the product., its porosity, density, or mechanical and physical properties. Conclusions are drawn on the basis of studies of this type as to the probable effect of gases on these properties. 4, 5, 0 In the present investigation an attempt has been made to obtain quantitative data on the analysis and quantities of gases associated with copper powders manufactured in different ways. Apparatus was constructed to collect gases evolved from loosely packed powder samples on heating to various temperatures under a reduced pressure of helium. The powders were outgassed thoroughly in a vacuum prior to starting the collection operation in order to eliminate mechanically entrapped gases and to prevent the possible reaction of the powder with these gases. Experimental Procedures Materials—The major portion of the investigation was carried out on a single heat of water-atomized, oxygen-free, high-conductivity copper. A relatively coarse fraction of this powder, 20 to 100 mesh, was tested as a mixed powder and as various graded size fractions. The microstructure of this powder showed equiaxed grains and was clean and free from oxides and oxide eutectic. The particle size, as determined

Jan 1, 1959

By R. E. Lamborn

A summary of oil and gas development in Ohio for 1935 must necessarily be brief. As attention of the state government to the oil and gas industry has never included the collection and compilation of statistics on production, either by producing sands, by counties, by fields, or for the state as a whole, such information as requested in Table 1 of this symposium is impossible to secure for this state. In the absence of production data chief attention must be directed to drilling activity for the year. Information such as can be compiled from various sources, including weekly drilling reports to operating companies and trade journals, is given in the following paragraphs with the realization that the data may not be complete in all its details. Drilling Activity by Fields Drilling activity during 1935 was similar to the preceding year in , that the major operating companies were generally content to drill lease-requirement and offset wells and in that comparatively little effort was made to discover new pools. A compilation of completions recorded in weekly reports to drilling companies and in trade journals show 1022 tests completed for the year in 53 counties of the state. Of this total number, 653 wells were commercial producers and 369 were classed as dry holes. Production was secured in 40 counties from formations ranging in depth to 5700 ft. and ranging in age from Middle Ordovician to upper Pennsyl-vanian. From the standpoint of new production for the year, the most important sands are the Clinton of Silurian age, the Berea of Mississippian age and the Shallow sands of Mississippian above the Berea and of Pennsylvanian age. Trenton Sand Field Production in the field of Trenton sand, which originally included parts of 15 counties in northwestern Ohio, is now on the decline. Seventy-three completions were reported in this field during 1935, of which 33.8 per cent were dry holes. Activity centered in Allen County with 12 completions, two of which were dry holes; in Hardin County with 11 producers; and in Wyandot County with 12 producers and 2 dry holes.

Jan 1, 1936

By R. E. Lamborn

A summary of oil and gas development in Ohio for 1935 must necessarily be brief. As attention of the state government to the oil and gas industry has never included the collection and compilation of statistics on production, either by producing sands, by counties, by fields, or for the state as a whole, such information as requested in Table 1 of this symposium is impossible to secure for this state. In the absence of production data chief attention must be directed to drilling activity for the year. Information such as can be compiled from various sources, including weekly drilling reports to operating companies and trade journals, is given in the following paragraphs with the realization that the data may not be complete in all its details. Drilling Activity by Fields Drilling activity during 1935 was similar to the preceding year in , that the major operating companies were generally content to drill lease-requirement and offset wells and in that comparatively little effort was made to discover new pools. A compilation of completions recorded in weekly reports to drilling companies and in trade journals show 1022 tests completed for the year in 53 counties of the state. Of this total number, 653 wells were commercial producers and 369 were classed as dry holes. Production was secured in 40 counties from formations ranging in depth to 5700 ft. and ranging in age from Middle Ordovician to upper Pennsyl-vanian. From the standpoint of new production for the year, the most important sands are the Clinton of Silurian age, the Berea of Mississippian age and the Shallow sands of Mississippian above the Berea and of Pennsylvanian age. Trenton Sand Field Production in the field of Trenton sand, which originally included parts of 15 counties in northwestern Ohio, is now on the decline. Seventy-three completions were reported in this field during 1935, of which 33.8 per cent were dry holes. Activity centered in Allen County with 12 completions, two of which were dry holes; in Hardin County with 11 producers; and in Wyandot County with 12 producers and 2 dry holes.

Jan 1, 1936

A. G. Cockbain—The paper by Burlingame, Bitsianes and Joseph is of great interest in extending the work done on high grade sinters, particularly that of Hessle, and the development and application to them of the technique of McBriar, Johnson, Andrews and Davies on ironstone sinters. In this laboratory the work of McBriar et al. has also been continued and extended to cover high grade sinters, and a sectioning technique similar to that used by McBriar et al. was attempted on sinter cakes made in the laboratory sinter unit, using magnetite concentrates (containing 64 pct Fe). In these experiments no attempt was made to flush out the products of combustion with nitrogen before cooling. It was considered that free air penetration would occur on only a limited scale with the size of sinter cake made (14 in. sq x 12 in. deep). Chemical analyses of the zones showed generally similar features of those described by Burlingame et al. and especially the FeO rich region at and just behind the flame front, i.e. zones of ignition and combustion. This seems to indicate that the nitrogen atmosphere does not materially affect the states of oxidation in the sinter cake or at least that special care is not required unless the sinter cake is small. Burlingame et al. consider that FeO present has some significant part to play in the mechanism of sintering. This view does not find favor with the author. The reduction of iron oxides in the presence of red hot coke is a well known phenomenon, whether conducted in an atmosphere of nitrogen or in a crucible in air, and in view of the presence of some carbon in the hot sinter, especially just at the ignition zone, cessation of the progress of the flame front will in no way affect the reduction of iron oxides near hot coke. Even in a nitrogen atmosphere some CO and CO, will be generated by reduction and by continual oxidation and reduction of CO as the transfer agent, the oxidation state of the iron oxides can be lowered quite rupidly so long as free carbon exists with enough heat. Knowing the composition of the gas at the flame front (obtainable by probes), it would be possible to calculate the static oxidation state of Fe2O3/Fe3O2 in equilibrium with it and hence obtain a check on the chemical analyses to see if in fact direct reduction of the Fe2O3/Fe2O1 to FeO has taken place. Have the authors attempted this? It appears to this writer that what is required is some means of reducing rapidly the heat content of the ignition zone and immediately behind, and at the same time insuring no oxidation by the air. In ironstone sinters the difficulty of oxidation state of the iron did not arise on account of the very large slag bulk. However, in high grade sinters knowledge of this, and also the mechanism whereby high oxidation states can be obtained in the final sinter, is of great interest. R. D. Burlingame (author's reply)—The question has been raised as to whether the high FeO content found in high-fuel sinters is due to actual reduction at the advancing flame front or due to unavoidable direct reduction during the quenching period. For such direct reduction to have taken place in the freshly-formed sinter, a considerable amount of solid carbon would have had to escape combustion and be available throughout the hot sinter zone during the quenching period. A simple stoichiometric calculation with the limited data available indicates that a zone of freshly-formed sinter over 2 in. wide must have averaged roughly 2 pct C to accomplish the amount of reduction found. Furthermore, the presence of this amount of carbon would indicate that the fuel in the charge had not burned over a narrow front but over a zone at least 2 in. thick. In contrast to such a condition, the data of the present investigation indicate that the combustion of fuel is confined mainly to a narrow front in which high temperatures and reducing conditions favor. the formation of excess ferrous iron.

Jan 1, 1959

By Richard D. Divine

In the Parkes process of extracting precious metals from lead, zinc is added to the molten lead containing gold, silver, copper, and some antimony. These metals, with the exception of antimony, form an alloy with the zinc by reason of their greater affinity for it than for the lead, and this alloy, being lighter than lead, rises to the top, carrying the precious metals with it, whence it can be removed by skimming. These skimmings are further treated for the separation of the zinc therefrom, and the recovery of the precious metals, the zinc being driven off by heat and again used for another operation. In addition to the zinc that combines with the silver, etc., a certain amount is necessary to saturate the lead, and it is therefore necessary to treat the desilverized lead to free it from this residual zinc. TO do this it is heated again in a reverberatory furnace and air or steam is blown through it. This oxidizes the zinc together with a small amount of lead and antimony, leaving the lead free from zinc and antimony, and forming oxides of these metals, which rise to the top and are skimmed off. This process relates to the separation of the metals in these oxides or skimmings. The skimmings are cooled, crushed, and mixed with carbonate of soda and pulverized oil coke. The mixture is heated in a reverberatory furnace on a bath of lead, to about 1,000" C. The metals are reduced by the coke, the lead and antimony go into the lead bath, while the zinc is volatilized and burned to oxide. This impure oxide is at the present time treated at Omaha by the Hall process of electrical precipitation, making a very pure metallic zinc. It can also be very easily refined by the old Schnabel process of using ammonia and carbon dioxide as a solvent. It seems to be in an ideal form for this purpose, and very few changes from the original method are required to obtain the zinc oxide practically C. P., leaving the lead and antimony as residues. There has been considerable difference of opinion regarding the effect

Jan 1, 1915

By W. N. Tanner

THE wire-rope hoisting conditions at the mines of the Anaconda Copper Mining Co. in Butte, Mont., are very severe because of the conditions under which it is necessary to operate. A study was made, in the fall of 1919, for the purpose of changing these conditions in order to obtain longer rope and sheave life. There are at present in Butte, hoisting engines equipped with wire rope as follows: 9 main hoists using flat ropes. 7 main hoists using 1 ½ in. rope. 5 main hoists using 1 ¼ in. rope. 6 shafts using 1 1/8 in. rope. 2 chippy hoists using 1 ¼ in. rope. 9 chippy hoists using 1 1/8 in. rope. 15 shafts using 1 in. rope. 7 shafts using 7/8 in. rope. 1 shaft using ¾ in. rope. In addition, there are a number of sinking engines using 5/8 in., ¾ in., 7/8 in., and 1 in. (15.9, 19, 22, and 25 mm. rope.) The flat ropes run from ½ by 7 ½ in. (12.7 by 190.5 mm.) to ½ by 4 ½ in. (9.5 by 114 mm.) and are used on the older hoisting-engines, which are set comparatively close to the shaft. Because of swelling and moving ground at some of the shafts, these ropes present certain difficulties in operation that are more pronounced than with round ropes; they are, therefore, being superseded by round ropes as newer engines are being installed. They are, however, much more easily inspected and repaired than round ropes.

Jan 2, 1922

By Olin M. Hart

Uranium ores occur in the Lower Cretaceous Inyan Kara group of heterogeneously stratified fluvial and fluvial-marine sandstones in the Black Hills of western South Dakota and northeastern Wyoming. There are three principal mining districts, each in the ancestral and present drainage area of a major river partially responsible for stripping the region to its present topographic form. Primary minerals in the deposits are coffinite and uraninite with minor amounts of paramontroseite and haggite. The ore minerals coat sand grains and fill interstices of complexly cross-stratified sandstone along solution fronts similar to "roll" type deposits of the other districts. Minerals of oxidized deposits are typically carnotite and tyuyamunite with different proportions of secondary vanadium accessory minerals. Ground water was the transporting medium and deposition of primary uranium and vanadium minerals occurred in reducing environments produced and controlled by physio-chemical characteristics of the sedimentary rocks.

Jan 1, 1968

By JOHN R. SUMAN

I WOULD like to spend a few minutes describing to you the present condition which exists in the oil industry and then point out some aspects of this deplorable situation in which I think petroleum engineers can be helpful. As you know, the oil business at this time is in a very critical condition, .due to the tremendous potential production in excess of current demand. This is a world-wide condition as well as a national problem, as it is estimated that the surplus production available for the market in foreign countries is of about the same proportion as that existing in the United States. Due to the inability within the United States to hold production within the bounds of demand prices have been slumping for the last four years and at this time have reached the point where the sales value of the average barrel of crude oil in the United States, is far below the cost, of production. In addition to the large amount of potential production available for the market in excess of demand we have in storage in the United States about six hundred fifty millions of barrels 'of oil. Unless something can be done to limit the amount of oil coming onto the market to a point well below the demand, which point will permit the reduction of stocks, it looks as though the 'oil business is facing demoralization.

Jan 1, 1931

By R. J. Tailleur, M. Rosenberg

Oil well drilling muds prepared with lubricating aids such as oil, graphite or mica will not produce a sufficiently strong protective lubricant film for the bit bearing surfaces under high load conditions encountered in drilling operations. Consequently, the damage to the bearing surfaces resulting from the absence of such a film frequently results in a shortening of the drill bit life. Several different types of extreme pressure lubricating additives for use in muds have been developed. These arlrlitives are capable of providing a protective lubricating film for bearing surfaces subjected to high load pressures. A modified version of the Timken lubricant tester, an instrument commonly used for testing the extreme pressure lubricating properties of oils, is used for measuring and controlling the lubricating qualities of the mud. Comparison tests made in the laboratory with 55/8-in. tricone bits drilling on steel plates immersed in extreme pressure lubricating muds and conventional muds showed that the bearing life of those bits tested in the lrrbricating mud was three to four times greater than obtained with conventional muds. Drilling tests made with extreme pressure lubricating muds in West Texas increased over-all bit life three to fourfold, reduced drilling torque and wear on drill pipe and drill collars. INTRODUCTION Roller bit cones contain roller, ball and journal-type bearings that are subjected to very heavy loading during drilling operations in which the only lubricant available for these bearings is either water or drilling mud. These bearings must be able to operate satisfac- torily in order for the cutting structures on the surface of the cones to be fully utilized. Frequently, the bearings wear to the point that the cones freeze and the bit must be pulled before the cutting structures on the cones become worn. In some instances the bearings continue to turn with severe wear but the cones, which are held on the bit by the bearings, drop off; and this causes an expensive fishing job. In other instances the bearings wear to the point that the cones pinch in causing an undergauge hole and delays to ream the hole. The advantage of increasing bit bearing life is self-evident. Because of inability to control the internal wear of bits while drilling, it was felt that improvement of the lubricating qualities of the circulating mud would be helpful. However, the often-discussed lubricating property attributed to muds has been a rather vague and intangible one. The literature has implied that the oil-emulsion muds are more effective lubricants than non-emulsion muds. Actually, there has been no direct method of measuring the lubricating property of muds which would indicate that one mud was better than another; there has been no way to determine whether the lubricating property of any mud was adequate. Furthermore, in comparing lubricating properties of muds, two qualities should be considered—the coefficient of friction and the extreme pressure lubricating qualities. For example, graphite can reduce the coefficient of friction, but does not provide a strong enough lubricating film to protect bit bearings subjected to high loads. The primary object of the investigation reported herein was to find a method for prolonging the bearing life of drill bits; and considering the heavy loads used in drilling, it was felt necessary to find both a method of measuring lubricating properties under high load conditions and methods of establishing effective lubrication under these conditions. Extreme pressure lubrication deals with that realm of lubrication where metal surfaces are in rubbing contact with each other under very high pressures. These pressures may be quite high, as for example,

By Henri V. Reibell

Deep open pit optimization supposes very long and sedious calculations in order to assign the best shape of the pit and the best bottom level, which will give the biggest profit. Computers give the possibility to make these calculations. More over, they allow to multiply trial calculations so that it is possible to obtain more reliable results. The paper does not expose the computer program but only the way in which mining engineers can use it.

Jan 1, 1969

By G. B. Walker, S. J. Swainson, S. A. Falconer

DURING the past few years much interest and attention has been focused on a relatively new method of ore concentration, which utilizes the principles of sink and float and employs as the heavy medium a suspension in water of a finely ground solid, such as galena or ferrosilicon. Although a relatively recent development, much progress has already been made in applying heavy-media separation processes to a considerable number of ores. Eight plants in this country and abroad -are now treating approximately 10 million tons of ore annually by heavy-media separation (sink-float) processes, including lead-zinc, lead, iron, garnet, tin and tungsten. At the annual meeting of the A.I.M.E. in 1941, three interesting papers (unpublished) dealing with heavy-media separation (sink-float) processes of ore concentration as practiced in four commercial units in the United States were presented by Victor Rakowsky, Grover Holt, Elmer Isern and Robert Ammon. These papers gave an excellent exposition of the principles of sink and float, as well as the operating practice in two iron-ore-beneficiation plants, the Harrison and the Merritt, of Butler Brothers, in Minnesota; the Central mill of the Eagle Picher Mining and Smelting Co.; and the Mascot mill, of the American Zinc, Lead and Smelting Co. Augmented by pictorial descriptions and a working model demonstrating the processes, these papers evoked a great deal of interest and discussion. In fact, in reporting the high lights of the meeting in the April 1941 issue Of MINING AND METALLURGY, Professor Taggart made the statement that "preconcentration by heavy suspension was Miss A.I.M.E. 1941 so far as milling is concerned." Although to date the greatest application of heavy-media separation from the tonnage point of view has been for the treatment of lead, zinc and iron ores, these processes have a much wider field of usefulness. In this regard, it is to be noted that recently new heavy-media separation plants for treating cassiterite ore and garnet ore have been placed in successful operation. Moreover, numerous other types of ores have been found to respond well to these processes when tested on a semi-commercial scale, and it is expected that in the near future a considerable number of new plants will be erected. In view of the fact that heavy-media separation processes offer such attractive possibilities, particularly now, when the mining industry is being called on for an even larger production than ever before has been attempted, despite shortages of labor and supplies, it was felt that a description of some of the successful separations that have been worked out during the past year in the Ore Dressing Laboratory of the American Cyanamid Co. on a variety of ores of strategic importance would be of interest. The purpose of this paper, therefore, is to present the essential data relating to investigations of heavy-

Jan 1, 1943

By B. K. Parekh, W. M. Goldberger

A novel process is proposed for continuous removal of ash and unreacted solids which become suspended in the oils obtained during coal liquefaction. The proposed method uses water in direct contact with the oil under conditions which cause the suspended residue solids to transfer from the oil to the water phase. Separation of the phases yields a product oil essentially free of suspended solids. The water is cooled, clarified or filtered by conventional low-cost systems, and recirculated. The paper describes experimental work leading to development of the novel concept and includes the result of batch experiments that establish the feasibility of the process.

Jan 1, 1980

By Berlen Moneymaker

THE development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration, Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its princi-pal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration.

Jan 1, 1938

By Howard N. Eavenson

ALL of the matters so far taken up by the Institute Committee on Stabilization of the Coal Industry will be of help, but it seems to be that under present conditions not very much can be expected until the railroad situation has been improved. As an instance of this, I would cite the fact of our experience at our mines in West Virginia and Kentucky. During 1917 and 1918 at our West Virginia plants we produced for our own consumption, practically entirely in the Chicago district, about 4,750,000 net tons of coal. In 1919 our output was reduced to 3,500,000 tons, this being caused partly by the shortage of orders in the few months following the armistice, but more particularly by The car shortage which began last September and continued throughout the remainder of the year, with the exception of December. This car shortage has been more acute since the first of the year, and while we now have an actual capacity here of 20,000 tons daily and have the equipment to produce it, with the possible exception of a few houses, we are able to average only about 12,000 tons, and in consequence, about 30 per cent. of our by-product ovens in the Chicago district are idle, and a number of blast furnaces are down for the want of coke. These figures, of course, refer to conditions before the strike of switchmen in April was started.

Jan 1, 1920

By R. K. Hopkins

Fox a great many years fusion welding has been used in and around petroleum refineries, but it is only within six or seven years that the more important pressure vessels have been constructed by this process, because before that time the properties of fusion welds would not withstand such rigorous service. Since the adoption of fusion welding for the construction of this equipment, the refiner has required pressure vessels suitable for operation over a very wide range of conditions. On the one hand, vessels must operate at extremely high temperatures, in the range of 950° to 1000° F., and on the other vessels must be suitable for operation at sub-zero temperatures down as low as -75° F. Also, vessels are required suitable for operation at pressures upwards of 1000 lb. per sq. in., and as low as a 29-in. vacuum. In addition, vessels are required to withstand the attack of very corrosive mediums. It has been a rather difficult task for the fabricator to meet all of these requirements, but as a result of the extensive research carried on by steel manufacturers and several fabricators of class I vessels, practically all of these demands have been met. In order to meet the refiners' requirements for this wide range of conditions, the fabricator has worked closely with the metallurgist. This has enabled him to choose the proper base metal for each service condition, but it has been the fabricator's problem to develop a welding rod and welding technique, as well as a heat-treatment, that would produce in the welded vessel characteristics in and around the weld comparable to those in the base metal. Where corrosion is not a serious problem, and where the operating temperatures are not too high, ordinary carbon steel has served very well. But when corrosion is serious, and/or when the temperatures are either very high or very low, it is necessary to use some form of alloy steel to give satisfactory service.

Jan 1, 1935

By J. H. Hollomon, L. D. Jaffe, M. R. Norton

In the practical heat-treatment of steel the decomposition of austenite usually occurs during cooling rather than at constant temperature. Nevertheless, the course of this decomposition has generally been studied only isothermally. Isothermal studies are not only simpler experimentally, but have the great theoretical advantage that one of the variables, temperature, is constant. It is the purpose of this paper to outline the principles that govern the relations between isothermal and anisothermalt‡ decomposition of austenite, to present and systematize the available experimental information, and to indicate the gaps in the existing knowledge. Some of the experimental information is the result of new work.§ Most of it is derived from scattered data in the literature. Many of these data were obtained incidentally in the course of research on other subjects and their significance has not been pointed out and perhaps not understood. It is hoped that this paper will aid future planning of more extensive research on anisothermal decomposition. Method In order to study the relations between isothermal and anisothermal decomposition, it appears fruitful to view anisothermal decomposition as taking place at a series of constant temperatures1 (except for the martensite reaction, which does not occur isothermally to an appreciable extent). When the time the steel is at each temperature is finite, the over-all amount of the reaction is considered to be the sum of the amounts occurring at each of the successive temperatures. During continuous cooling or heating, the time the steel is at each temperature and the difference between successive temperatures can be considered to approach zero. The over-all amount of transformation will then be given by integration over the range of temperatures involved. This point of view is advantageous in that it considers anisothermal transformation to be a series of isothermal transformations. The problem thus becomes one of determining the effect of partial decomposition at any given temperature upon subsequent decomposition at another temperature. Single Anisothermal Reaction Consider a phase brought to a temperature at which it is unstable, held there until it has partially transformed, and then brought to another temperature at

Jan 1, 1947

By L. D. Jaffe, M. R. Norton, J. H. Hollomon

In the practical heat-treatment of steel the decomposition of austenite usually occurs during cooling rather than at constant temperature. Nevertheless, the course of this decomposition has generally been studied only isothermally. Isothermal studies are not only simpler experimentally, but have the great theoretical advantage that one of the variables, temperature, is constant. It is the purpose of this paper to outline the principles that govern the relations between isothermal and anisothermalt‡ decomposition of austenite, to present and systematize the available experimental information, and to indicate the gaps in the existing knowledge. Some of the experimental information is the result of new work.§ Most of it is derived from scattered data in the literature. Many of these data were obtained incidentally in the course of research on other subjects and their significance has not been pointed out and perhaps not understood. It is hoped that this paper will aid future planning of more extensive research on anisothermal decomposition. Method In order to study the relations between isothermal and anisothermal decomposition, it appears fruitful to view anisothermal decomposition as taking place at a series of constant temperatures1 (except for the martensite reaction, which does not occur isothermally to an appreciable extent). When the time the steel is at each temperature is finite, the over-all amount of the reaction is considered to be the sum of the amounts occurring at each of the successive temperatures. During continuous cooling or heating, the time the steel is at each temperature and the difference between successive temperatures can be considered to approach zero. The over-all amount of transformation will then be given by integration over the range of temperatures involved. This point of view is advantageous in that it considers anisothermal transformation to be a series of isothermal transformations. The problem thus becomes one of determining the effect of partial decomposition at any given temperature upon subsequent decomposition at another temperature. Single Anisothermal Reaction Consider a phase brought to a temperature at which it is unstable, held there until it has partially transformed, and then brought to another temperature at

Jan 1, 1947

By R. T. Hukki, P. Voutilainen

This paper describes a new apparatus for continuous wet fine-screening. Its preferred size range seems to be from 0.1 to 1 mm. The supercritical trommel screen is a short cylindrical trommel of wedge-bar type construction operated at a speed greater than the calculated theoretical critical speed and at a speed lower than the speed at which particles introduced into it will centrifuge. The paper describes results obtained with the prototype supercritical trommel screen in pilot plant scale. The results point to a high capacity and simultaneously to a high sharpness of screening. Finally, an analysis is presented of the forces acting in screening on a supercritical trommel screen. In the era of high speed, high capacity processing of raw materials the conventional slowly rotating trommel screen is often considered a relic from the times passed. A typical trommel screen is the cylindrical trommel rotated about a horizontal or slanting axis at a relatively low speed. Its screening characteristics are well known. Trommel screens of various types of construction, methods of operation, performances and other characteristics have been described in detail by Taggart.1 The theoretical critical speed of a trommel screen is defined by the same well known equation as that applied for grinding mills: where ncritical = the numerical value of the theoretical critical speed in rpm, D 1 = the inside diameter of the trommel in feet, and D2 = the inside diameter of the trommel in meters. ncritical corresponds also to the centrifuging speed provided that the coefficient of friction f between the trommel surface and the outer layer of the charge is = 1.0. In a general case: From Eq. 2 it is seen that in all cases where f < 1.0 the centrifuging speed of the trommel is greater than the theoretical critical speed. The supercritical trommel screen concerns screening operations within that speed range which is between the theoretical critical speed defined by Eq. 1 and the centrifuging speed defined by Eq. 2, under conditions such that the coefficient of friction f<1.0. It is reported by Taggartl that the optimum speed of a conventional cylindrical trommel screen 36 in. in diam was experimentally found to be about 16 rpm. From Eq. 1, the critical speed of this trommel is 44.2 tpm. The indicated optimum speed corresponds to (16/44.2) x 100% = 36.2% of the theoretical critical speed. The optimum speed range based on information available seems to vary from 33% up to 45% of the theoretical critical value. The trommel screen operated at a supercritical speed: operates at a speed greater than the calculated theoretical critical speed; operates at a speed lower than the speed at which the charge introduced into it will centrifuge; operates within the supercritical speed range in such a way that the coarse fraction of the charge must slide in respect to the inside surface of the trommel; the outer layer of the said fraction next to the screen tends to proceed in the same direction as any selected point on the trommel surface, but now at a lower speed, and indeed at a subcritical speed; allows to a certain degree adjustment of the maximum determining particle size x of the fine product simply by a variation of the speed of the trommel within the supercritical speed range. With increasing trommel speed, finer and finer material only will get the opportunity to find its way into the fine product while the screen opening remains constant. In conventional practice, the low speed trommel is generally used for sizing of coarse and medium coarse material, but seldom for fine screening. The characteristic feature of the product passed through the conventional trommel is that the determining size x of the biggest particle is barely smaller than the nominal size of screen opening. The supercritical trommel screen, on the other hand, is best suited for sizing of relatively fine material. Furthermore, the characteristic determining size x of the biggest particle in the fine product can be substantially smaller than the nominal width of the screen opening or slot. In the trommel screen best suited for the applications

Jan 1, 1965