Search Documents

By K. T. Aust

The occurrence of annealing twins in high-purity aluminum resulted in the formation of grain boundaries having orientation relationships which correspond to a high density of coincidence sites. The results provide support for the coincidence site model and indicate that large-angle coincidence boundaries have lower free energies than large-angle noncoincidence boundaries. Observations are presented concerning the coherent structure of twin interfaces in aluminum and the importance of inter-facial energy in preferred orientation. RECENT experiments1 have shown that when an annealing twin is formed during grain boundary migration in zone-refined lead, a large-angle random boundary is replaced at the growth front by a large-angle coincidence site boundary. The coincidence site orientation relationships obtained by twinning were of the type considered by Kronberg and Wilson,2 Frank,3 and Dunn.4 On the basis of the theory of annealing twins advanced by Fullman and Fisher,5 these observations indicate that the energy of a coincidence site boundary is less than the energy of a random boundary by an amount which exceeds the energy of the coherent twin boundary. This energy difference between the coincidence and random boundaries must be at least about 5 pct since the ratio of twin boundary energy to grain boundary energy in zone-refined lead is 0.05 * .014.6 Fullman7 has found that the twin boundary energy in aluminum is about 21 i 5 pct that of a large-angle grain boundary. A twin boundary energy as large as this would be expected to exclude the formation of many coincidence site grain boundaries, especially those which have a relatively low density of coin- cidence sites. Therefore, if the coincidence site model is a useful interpretation of certain large-angle boundaries, then it would be predicted that only coincidence boundaries which separate adjacent crystals with a relatively high density of coincidence sites may be obtained as a result of twinning in aluminum. The present experiments provided a means of testing this prediction since annealing twins occurred during the growth of recrystallized grains into striated, melt-grown single crystals of zone-refined aluminum. EXPERJMENTAL PROCEDURE A striated single crystal of zone-refined aluminum, about 1 cm sq and 37 cm in length, was obtained during zone melting of aluminum of 99.996 wt pct starting purity in a graphite boat under helium atmosphere.8 A molten zone of 2 to 3 cm in length, which was maintained by induction heating. was passed along the length of the bar for eleven passes at a rate of 0.9 mm per min. An additional final pass was given at a rate of 0.2 mm per min. The center portion of the zone-melted bar was characterized by an electrical resistivity ratio between room temperature and 4.2° K of 8000 to 9000. Single crystals of 1 to 2 cm in length were removed from the center section of the zone-refined bar and electrolytic ally polished in a 2:l solution of methyl alcohol and concentrated nitric acid. The specimens were then chemically polished in Alcoa R-5 solution. X-ray analysis of the single crystals indicated the presence of striations or lineage substructure having misorientations as high as 2 deg. New, recrystallized grains were introduced into each striated crystal by the technique of artificial nucleation and growth, previously described.9 During the growth of the recrystallized grains at 300' to 600°C in argon, it was sometimes found that a

Jan 1, 1962

'T. C. MERRIMAN, New Haven, Conn. (written discussion *).-This most interesting paper gives much carefully obtained and valuable data. However, there are two points in connection with the commercial application of such data that might possibly be a source of trouble and mis-understanding. In the first place, the examination of thin sections of annealed brass, subjected to standard Brinell test.(500 kg. on a 10-mm. diameter ball) at thicknesses from 0.075 to 0.150 in. (1.9 to 3.8 mm.) indicates that cold work has been performed on the specimen during the application of the load sufficient to extend way through the section, and have the hardness of the metal affected by the backing. If the usual steel support is used, this effect is very evident. If a piece of soft brass is used as a support, there is an indentation in the surface of the support accompanied by a bulge on the under side of the tested specimen opposite the impression made by the 10-mm. ball. The result is that Brinell specifications (governmental or otherwise) on stock for a certain purpose may not be fair in all cases, since manufacturers, owing to differences in equipment, etc., may not all use precisely the thickness and conditions of stock on which the Brinell specifications were based. This would mean that the government Brinell specification might not give them the temper of stock best suited for their manufacturing methods. The concluding paragraph of this paper, stating that "the hardness of cartridge brass may be determined with greater accuracy by the Brinell hardness measurement than by attempting to judge it from the grain size" appears to be in line with the movement of the last year or so among brass manufacturers toward substitution of the Brinell test for microscopic examination as an acceptance test on cartridge brass. The statement may he strictly true that the Brinell test is the best test for hardness, but it is not, as the statement might readily be construed, a sufficient test of suitable condition. For instance, some cartridge brass might accidentally have been overheated to a point where it would be distinctly unsafe to use for the manufacture of small arms cases and then be so rolled (reduction 3 to 5 per cent.) as to pass perfectly proper Brinell specifications. Under such conditions the microscope would reveal its unsuitability where the Brinell test had failed so to do.

Jan 4, 1919

By H. W. Gillett

Unlike most previous Howe lecturers, I had not the good fortune to be associated with Henry Marion Howe, nor to be directly one of his students. Yet, through his writings, he has been my teacher, as he has of all American metallurgists. Instructive as his writings are—I use the present tense because Howe thought so keenly and reasoned so surely, seeing clearly, as if by intuition, what was hazy to lesser minds, that his writings are still vital—it is not those books and papers, nor even the minds he trained in his classes, that were his most outstanding service. It was the spirit of Howe in his approach to the problems of metallurgy, his broad-mindedness and fairness, his recognition of the need for theories and hypotheses to explain metallurgical phenomena, his willingness to use them as servants, as well as his questioning attitude—his refusal to accept them as masters—that comprise his greatest service. This most thoroughly warrants the honor the Institute pays each year to his memory. These traits I so respect and honor in any man that I glory in this opportunity to do reverence to him in whom they were so notably united. Howe's Discussion of a Creep Problem I have often wished that Howe were still with us to turn his keen insight upon the problems of the use of metals at high temperatures, a field much studied but still very hazy. Indeed, 53 years ago, in a paper1 before this Institute, Howe stated a problem closely allied to some that still perplex metallurgists and engineers dealing with the high-temperature field. Howe was intrigued by a report2 from another old master, Robert Henry Thurston, on the behavior of annealed vs. cold-drawn iron wire, and in order to broaden the foundation for metallurgical generalization, Howe made experiments of his own on copper and silver. In these tests by Thurston and by Howe, the wires were rapidly loaded to determine the

Jan 1, 1939

Texture Transition in Ordered CuAu, by E. A. Starke, Jr., J. C. Ogle, and C. J. Sparks, Jr., Trans. TMS-AIME, 1969, vol. 245, pp. 169-70. pole figures should have had two parts not one. On the Estimation of Oxygen Absorption by Continuous Molten Metal Streams, by J. Szekely, Trans. TMS-AIME, 1969, vol. 245, pp. 341-44.

Jan 1, 1970

By S. B. Casey

[ ] IN 1880, an electric arc was struck over metal for the first time to experiment with controllable melting. The glare of this arc has reflected on the stacks of the steel industry and continued to light the path of steelmakers in their never ending quest -for faster, more economical, and better ways of producing steel. William Siemens is credited with first employing the electric arc to melt metal in a closed hearth and produce basic metallurgical reactions. By the turn of the century, an Italian, named Stassano, was experimenting with ore reduction by the electric arc. In 1899, Dr. Paul Heroult, in France, used the direct arc principle for producing ferro-chromium. His experiments quickly led him to develop a dosed-top arc furnace for the production of steel, and his first commercial shipment was recorded in December, 1900. American steelmakers, quick to sense the possibilities of this method of melting, invited Heroult to our shores, where, in 1905, he was responsible for installing the first arc furnace on the North American continent. This furnace, at Sault Ste. Marie, was built for ore reduction. But Charles Holcomb, founder of Holcomb Steel. Co. of Syracuse, N. Y. contacted Heroult in 1905 and contracted for the first American direct-arc electric furnace for steelmaking. On April 5, 1906, the first heat was tapped from this 3-ton unit. The furnace was basic lined and powered by a single-phase, 500 kw generator, -producing high amperage at low voltage. It is interesting to note that, although the first few heats were made with cold charges, subsequent heats were duplexed. R. H. Bully, first superintendent of Holcomb Steel, persuaded the directors to purchase the unit to effect a more economical and efficient means of making tool steel by duplexing prime melting in a combustion fired furnace, and transfer of hot metal to the arc furnace for temperature adjusting, refining, and adding carbon and alloying elements. Today, duplexing is foreseen by some as the steelmaking process of the future. The promise shown by America's first arc furnace for ingot production quickly led to the purchase of a similar unit by The Firth Sterling Steel Co., in 1909, and to the purchase of the first arc furnace for production of steel castings, by the Treadwell Engineering Co., in 1911. From its humble start in 1906, production of arc furnace steel has never ceased to increase its yearly percentage of total steel production in the U. S., although certain other methods have declined or almost disappeared. By its ability to be used intermittently, the arc furnace gained favor and enhanced its reputation during depression days. When the attack on Pearl Harbor plunged us headlong into the long days of World War II, the arc furnace stood ready, flexible enough to be overburdened hearth wise 30 pct and power wise 25 pct, pouring its endless flood of alloy for the guns, tanks, ships, and planes which ultimately brought victory. During the post war boom, the now, proven virtues of low initial cost, faster installation, better yield, improved availability, and lower operating cost, enabled industry-particularly the small, new, independent producers-to locate strategically and profitably to meet the demand of an America that had been starved for new homes, appliances, cars, and highways. In the Korean police action, the arc furnace again proved itself by providing the latest alloys metallurgists could develop to meet the demands that the jet age and the innovations of guided missiles required. In today's peacetime prosperity, the arc furnace is continuing to provide the economic flexibility required to meet an ever increasing demand for better steel in the face of mounting costs, scrap shortages, and pressure toward decentralized location of industry.

Jan 1, 1961

By W. F. Boericke

AT Kellogg, Idaho, J. Fred Johnson is driving the 5000.-ft Hooper Tunnel under contract for the Bunker Hill & Sullivan Mining Co. This was visited by a group of engineers during the recent meeting of the A. I. M. E. at Spokane, who were impressed with several features of the work. An excellent record of advance is being made by the contractor, over 47 ft. being driven in 3 days during October, and 223 ft. advanced in 29 shifts. The size of the tunnel is 8 by 9 ft. The ground is Wallace quartzite and, save for the first hundred feet, stands well and does not require timbering. The grade is held uniformly at 0.5 per cent. Two shifts are employed, with two sets of machine men to the shift. Ingersoll-Rand S-70 drills are used. each machine being set up independently in the heading; 26-30 holes are drilled to the round; using 1 1/4: in. round hollow drill steel. A 7-hole cut is required, and these holes are blasted simultaneously, using 60 per cent gelatine, 12 sticks to the hole. Instantaneous and fire delays of electric detonators are used for the complete round. A feature of the drilling is the use of long carriage drills, necessitating fewer changes of steel, and more time spent on drilling, with less time consumed taking steel back and forth from the face. Of course, this means better blacksmithing so that the drill steel shall stand up for the added footage.

Jan 1, 1930

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION TO OCTOBER, 1904 Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 28 Montreal, Canada Sept, ?79 8

Jan 1, 1923

Organization Place - Date 1918 American Iron and Steel Institute New York, N. Y. May American Water Works Association :.. St. Paul, Minn. May 20-25 American Institute of Chemical Engineers Berlin, N. H.. June 19-22 American Concrete Institute Atlantic City, N. J. June 24-26 American Society for Testing Materials Atlantic City, N. J. June 25-28 New York Electrical Society New York, N. Y. June National Association of Stationary Engineers Cincinnati, 0. Sept. 9-13 National Exposition of Chemical Industries New York, N.Y.. Sept.23-28 American Chemical Society Cleveland, 0. Sept. National Petroleum Association Atlantic' City, N. J. Sept.

Jan 5, 1918

By Robert Linton

AT its meeting on May 21, the Board of Directors approved the recommendations submitted by President Lovejoy and named a nominating committee for the year that is especially well distributed as to major technical interest and as to geography. As may be seen from the list published herewith, two come from the East, two from the Midwest, and three from the far West. Mr. Linton, the chairman, has been a valued member of the Institute for 36 years. A memorandum drawn up by Paul D. Merica, representing the A.I.M.E., and W. R. Barclay, representing The Institute of Metals of Great Britain, setting forth a reciprocal plan for special memberships in each Institute for members of the other, was discussed. Both societies already have formally approved the plan in principle and Dr. Merica was clothed with full authority to agree on a few small details that have not been settled, and conclude the arrangement in behalf of the Institute.

Jan 1, 1936

Jan 1, 1891

By A. Lawley S. Schuster

The tensile behavior of copper foils prepared from rolled bulk material has been studied over the thickness range 2 to 53 , and for a range of pain sizes. For foils of comparable grain size, having the cube texture and tested along (100), yield strength increases with decreasing foil thickness t below -26p, with a corresponding decrease in ductility. Deformation occurs in the form of localized slip clusters distributed throughout the gage section. To the extent that the tensile strength (10 to 18 kg mm-) is unaffected by foil thickness, and that the foils possess fair ductility, the stress-strain behavior resembles that of bulk material rather than that of whiskers or evaporated films of comparable dimensions. The dependence of yield strength o on foil thickness t below -26p is of the form: oy = oo + kt-1/2. Possible explanations for the stress increase are considered based on 1) the dependence of active dislocation source length on foil dimensions, 2) the locking of surface sources, or the blocking of mobile sources at the surface due to surface film. It is now well-established that filamentary whiskers of many materials show exceptionally high strength compared with bulk crystals.'-11 As the diameter of the whiskers decreases to -1, the observed fracture strength approaches, and in certain cases exceeds, the calculated shear stress for the nucleation of slip in a perfect crystal.' In general, the stress-strain curve is entirely elastic, with strains at fracture approaching 1 pct. Similarly, thin films12-24 of evaporated or electrodeposi-ted material have been shown to possess tensile strengths three to seven times that of bulk material, with total strains at fracture -1 to 2 pct. In the present study, attention has been directed to the room-temperature tensile behavior of thin foils of copper over the thickness range 2 to 53, prepared from rolled bulk material. Yield stress, ultimate tensile strength, elongation to fracture, and work-hardening behavior are measured as a function of grain size and foil thickness. Structurally such foils are superior to either evaporated or electrodeposited films, and in the recrystallized condition exhibit considerable ductility. Apart from preliminary work by Sumino and Yamamoto25 on the work-hardening behavior of rolled and recrystallized copper foils, no systematic tensile studies have been carried out on material of this form. EXPERIMENTAL PROCEDURE Tensile specimens were prepared from 99.995 pct purity rolled copper foils of thickness 2, 6, 12, 26, and 53, obtained from the Hamilton Watch Co., Lancaster, Pa. Irrespective of specimen shape, it is necessary to use tensile foils with edges free from notches or tears. To this end, any form of cutting operation was excluded, and the tensile foils prepared using a photoengraving process, the details of which are described elsewhere.26 Since tensile data are required under conditions of uni-axial stress, the specimen shape is extremely important. Ideally, the foil should be infinitely long, allowing a gradual taper from the grip area to the gage section; however, from a practical standpoint, long foils are easily damaged during testing. A modified tensile specimen was therefore selected having a parallel gage section 1.25 by 0.20 in. with a tapered shoulder section increasing to 0.5 in. at the grips, and an over-all length between grips of 4 in., Fig. 1. In practically all tests, these foils fractured within the parallel gage section. By approximating the foil contour (Fig. 1) to a hyperbola it is possible to analyze the stress distribution in the tensile foil using two-dimensional elasticity

Jan 1, 1964

By Linn M. Farish

The estimated production of petroleum in the Dominion of Canada for 1931 was 1,582,000 bbl., an increase of 60,000 bbl. over 1930. Nearly all of the production came from Alberta, with a small quantity from Ontario, and a very minor amount reported from New Brunswick. At the beginning of 1931 it was hoped, and predicted, that a substantial increase in production would be shown for that year, but such was not the case, since Alberta did not show the anticipated gain. The production from Ontario and New Brunswick has not varied more than a few thousand barrels during the past 10 years and aggregated 124,000 bbl. in 1930, with 126,600 bbl. estimated for 1931. Unless new fields are discovered, production in 1932 will decline, with Ontario and New Brunswick showing little change and Alberta declining appreciably. Canadian production by provinces during the past 10 years is given in Table 1. Furnished by the Dominion Bureau of Statistics. a Barrels of 35 Imperial gallons or 42 U. S. gallons. c Figures for Ontario and New Brunswick are estimated. The production of natural gas in Canada reached the record figure of 29,377,000,000 cu. ft. in 1930 and it is estimated at 26,874,600,000

Jan 1, 1932

By John S. Brown

The northeastern United States embraces that area of the Appalachian Mountains, and adjacent territory, beginning on the south at the Potomac River. It thus extends from the flat-lying Paleozoic terrane of the Appalachian plateau on the west, across the folded Paleozoics of the Great Valley and adjacent ridges (Paleozoic and Precambrian), over the Piedmont and New England metamorphic complex (mixed Paleozoic and igenous rocks), broken by the great Triassic rift remnants, onto the subdued coastal plain of Cretaceous and Tertiary sediments. Although not noted as a metal mining region, the area does contain numerous substantial and several outstanding mines, chiefly of the more prosaic metals, particularly iron, zinc, and copper, as well as many minor occurrences of these and a few additional items. These deposits occur to some extent in every subdivision of the area. The region to date (1966) has produced almost 500,000,000 tons of medium to lowgrade iron ore, especially magnetite, including ilmenitic magnetite; 50,000,000 tons of highgrade zinc ore; and 5,000,000 tons of lowgrade copper. In the past, it has yielded small amounts of chromite and nickel, and at present is a large producer of titanium. Precious metals are conspicuously absent, and so also are the Tertiary or Mesozoic igneous phenomena so commonly associated with mines of the West. Hence, a survey of the extensive mineralization · of this region should be instructive

Jan 1, 1968

By Fred D. Gustafson

With the postwar emergency for new housing and for new industrial buildings, much research has been done on lightweight aggregates for use in concrete and plaster. The trend toward lighter weight aggregates to relieve the dead load on the higher, steel frame- work buildings started toward the end of the last century. Progressively the requirements be- came more stringent, crushed bank slag, weighing 80 lb per cu ft as com- pared to 100 lb for crushed rock, was supplemented in some sections by foamed slags and expanded shales weighing from 40 to 60 lb per cu ft. In other sections cinders were used weighing from 40 to 50 lb, including sand. Sections favored with more recent vulcanism turned to pumice weighing from 30 to 60 lb, whereas other localities made use of diatomite, from 28 to 40 lb. Exfoliated vermiculite weighing from only 6 to 10 lb per cu ft came into use. As the search for lighter weights in aggregates continued so did the search for other desirable properties such as nailability, ease of cutting or channeling, and good insulation to both sound and heat. This search eventually led to a widespread interest in the expansion of perlite, or similar volcanic glasses, with the result that in 1946, the Office of the Housing Expediter' listed eleven firms reporting the operation of processing plants either on pilot or commercial scale producing aggregates weighing from 2 to 16 lb per cu ft.

Jan 1, 1949

By T. F. Witheree

The Fletcherville Furnace was built in 1864 and 1865, making its first blast from August until October of the latter year, when it was blown out to prevent its " bunging-up." Repairs were made in time to enable it to be blown in again December 12th, 1865, the blast ending October 7th, 1866. Total product 1921.15 tons iron, an average of 6.8.2.5 tons per day, from ores yielding 44.8 per cent. Consumption of charcoal 223.2 bushels per ton of iron. The furnace journal up to this time shows no record of furnace dimensions, or temperature of the blast, but as near as can be ascertained, they were as follows, viz.: Height of stack, 42 feet. Diameter of bosh, 11 feet. Angle of bosh, 71/2 inches to 12 inches rise, about 58°. Diameter of open tunnel head, 42 inches. Number of tuyeres 3 ; each 3 inches in diameter. Dam 15 inches high. Tuyeres 24 inches high. Tymp 224 inches high. Diameter of steam cylinder, 20) inches. } Diameter of blast cylinder, 64 inches. } Stroke 5 feet. The engine is direct-acting horizontal non-condensing. December 26th, 1866, the furnace was again put in blast, having been considerably altered in the crucible; the height of stack, bosh, and tunnel head remaining as before. Six tuyeres were put in, three in each of the side arches. The hearth or crucible was rectangular in form, 3 feet wide x 31/2 feet long x 64 feet high. Inclination of bosh 58°. Height of tuyeres 26 inches; nozzles 21/4 inches diameter. Temperature of blast estimated to be about 500°.

By B. J. Guarnera

There have been major changes in the makeup and nature of the uranium exploration industry in recent years. Significant price increases precipitated an increase in exploration activity-according to the Department of Energy, exploratory drilling in 1977, by 140 companies, was almost 8 million m (26 million ft). This represents a 37% increase over the prior year's drilling. Projections for 1978 indicate at least 9 million m (30 million ft) of exploratory holes will be drilled in the US. Exploration expenditures in 1979, including land acquisition, drilling, and other costs, were estimated by DOE at over $236 million. Domestic expenditures for 1978 are estimated at over $250 million.

Jan 10, 1978

By AIME AIME

THE John Fritz Gold Medal for 1929 was presented to Herbert Hoover at the Executive Mansion on April 25, at a luncheon given by Mr. Hoover to present and past members of the Board of Award, preceding medalists, and presidents and secretaries of the American societies of Civil, Mining and Metallurgical, Mechanical, and Electrical Engineers. The presentation party of forty engineers which gathered at the White House, from all parts of the United States, was made up of past presidents of the four senior national engineering societies that established the John Fritz Medal and included five men who had received the medal in previous years. These former medalists were Edward Dean Adams, J. J. Carty, J. Waldo Smith, Elmer A. Sperry and Ambrose Swasey. This medal is the highest honor bestowed by these four national engineering societies, having a membership of 60,000. It is awarded not oftener than annually for "notable scientific or industrial achievement, without restriction on account of nationality or sex." In accordance with custom, the award to Mr. Hoover was made tentatively and without announcement in October, 1927, and was formally con- firmed and announced one year later.

Jan 1, 1929

By Edwin M. Chance

EDWIN M. CHANCE, Wilkes-Barre, Pa. (communication to the Secretary*).-I have read with great interest Mr.. Liebermann's paper reporting dynamometer tests of mine cars and wish to express my appreciation of this investigation. The coal-mining industry needs just such precise study of the problems with which it is confronted.

Jan 10, 1916

By G. F. Olsen

ON superficial consideration a technical library might be considered a luxury to the business institution that possesses one. After all, public libraries and research institutions probably contain all the data that would be found in a private technical library, and able consultants are available both within and without a company. In all probability the technical men of a company have in their combined personal libraries sufficient information to answer most inquiries. Nevertheless, possession of such a department is of real economic benefit because of the time it saves its users, because it prevents expensive duplication of technical literature in a company, and lastly, but most important, be- cause it makes readily available a central storehouse of technical facts classified and indexed to meet the demands of the industry or industries concerned.

Jan 1, 1940

By D. I. Bardos, A. M. Bardos, Paul A. Beck

The approximate effective silicon radii in ternary Laves phase alloys with transition elements and silicon were found to range between 1.16 and 1.21A, i.e., considerably smaller than the atomic radius calculated for elemental silicon. The atomic radii were found to increase with the size of the transition element atoms in the structure. It has been noted by Aronsson1 that silicon in solid solution in iron, cobalt, and nickel has an effective CN 12 atomic radius of approximately 1.20Å, a value very much smaller than the CN 12 radius of 1.34Å derived from the interatomic distances in elemental silicon.7 The unusually short metal-silicon interatomic distances in transition element monosilicides and disilicides have been also pointed out by various investigators.1 A similar tendency was observed by Nevitt in Cr3O type silicides.2 Recent work on Laves phases in ternary systems of silicon with transition elements4"8 suggested that extensive Laves phase fields may occur in such systems.8 It has been pointed out by Laves7 that the MgCu2 and MgZn2 type structures lend themselves particularly well for the determination of the effective radii of the component atoms. In these AB2 phases the B atoms are arranged in close packed straight lines, and their distances are related in a simple manner to the lattice parameters.8 The present work was undertaken in order to find out whether or not the B transition element in such AB2 Laves phases can be replaced to an appreciable extent by silicon. In cases where extensive substitution proves to be possible, the "average atomic radius for the B site" at various silicon contents was to be determined, and the effective atomic radius of silicon calculated by extrapolation to complete replacement of the B component by silicon. The following ternary systems were studied: Ti-Mn-Si, Ti-Fe-Si, V-Co-Si, V-Ni-Si, Nb-Fe-Si, Nb-Co-Si, Ta-Fe-Si, Ta-Co-Si, and Mo-Fe-Si. In all of these alloy systems, the Laves phase solid solutions were found to extend over a considerable range of silicon content. As previously reported,4"8 in the V-Co-Si, V-Ni-Si, and Mo-Fe-Si ternary systems Laves phases do occur, even though there are no corresponding binary Laves phases. In stabilizing the Laves phase, silicon acts as if it were decreasing the effective electron concentration of the alloy.8 A more detailed study of the boundaries of the Laves phases in the V-Co-Si and V-Ni-Si systems has been made and will be published elsewhere. In both cases, the elongated Laves phase fields extend parallel to the B-Si side of the composition triangle, clearly showing that silicon is substituting for cobalt, respectively, nickel over a wide range of compositions. The binary Laves phases NbCo2 and TaCo2 have the cubic MgCu2-type structure. It was found that, in both ternary systems with silicon, again the MgZn2-type hexagonal Laves phase is stabilized and that this phase extends to high-silicon contents. In each ternary system at least three Laves phase alloys of the composition A(B1_xSix)2 were used, x here denoting the fractional substitution of the B-transition element atoms by silicon. The alloys, listed in Table I, were prepared by arc melting in argon. Each specimen was water quenched after a homogenizing anneal of 3 days at 110(FC, except for the Mo-Fe-Si alloys, which were annealed at 1200°C. Metallographic examination showed that most of the homogenized alloys consisted of a single phase, although some had minor amounts of a second phase, as shown in Table I. X-ray diffraction patterns were prepared using an asymmetrical focusing camera of large resolution and Fe Ka radiation. The patterns were indexed, and the lattice parameters of the hexagonal Laves phases were determined from the available diffraction lines of highest indices: (213), (205), and (313). The lat-

Jan 1, 1963