Search Documents

By Hjalmar W. Johnson

It has long been accepted that blastfurnace practice varies to some degree with the coke used. While the qualities desirablc in iron have been known for some time, the qualities in coke that produce such iron have not been established. There are no objective standards for blast-furnace coke, which is usually described in general terms, as good or bad. Many experienced operators believe that coke cannot be measured objectively except by using it in the furnace, noting the result, and labeling the coke according to furnace operations. This is admittedly unscientific, and besides is useless for the two main purposes for which a measure of coke quality is needed: (I) to produce the best possible coke from the coals and equipment on hand; (2) to test new coals and determine their value for blast-furnace coke. In seeking such an objective measure, much work has been done on tumbler tests, shatter tests, sizes of coke, porosity, specific gravity, reactivity or combustibility and other tests, but as yet very little has been published in which conclusive correlations have been established between such objective measures and furnace operation. In our study of the problem during the past 8 years we have developed no new measures of coke quality, but we have collected data that are presented here in the hope that they may assist in further work, so that at some future time there may be developed such positive measures. The purpose of this paper is to show that there are variations in coke and that such variations do influence the operation of blast furnaces. At the same time we must remember that there are variations in blastfurnace operation and it may be the blast furnace that is at fault. This correlation of coke properties with blast-furnace operation will be worked out in the following steps: . Discussion of a period when a change in the coke resulted in an increase in efficiency on one furnace and a decrease in efficiency on another. 2. Adaptation of the inefficient furnace to the available coke so that normal efficiency was restored. 3. The use of radial distribution: a discussion of the effect of size of ore layer in adapting blast-furnace operation to the coke. 4. An example of a change in size of coke and the detrimental influence on the pro duction of one furnace. 5. An example of a change in size of coke, together with manufacturing data, to show why it changed, the conclusion being that coke is a product with an optimum value. 6. Illustration of the fact that coke has different optimum values on two furnaces, with discussion on adaptation of operation so the optimum values will be the same. 7. Limitations of the use of screen tests as an objective measure of coke quality. 8. Importance of uniformity in coke. Functions of Coke and Qualities Required to Perform These Functions Coke has three important functions in a blast furnace: (I) to furnish most of the

Jan 1, 1942

By James S. Browning

For the past several years, USBM has conducted laboratory and continuous process development work on the weathered mica pegmatites ores of Alabama, Georgia, and North Carolina to determine the feasibility of recovering commercial-grade mica concentrates by flotation. The research has resulted in the development of two processes for flotation of mica: 1) an acid-cationic method for recovery of coarse mica and 2) an alkaline-anionic-cationic method for recovery of fine mica. The research indicated that the two processes may be effectively utilized separately or in combination for flotation of mica from weathered pegmatite ores. This report summarizes the process development work, and demonstrates the feasibility of producing commercial-grade concentrates with a high recovery of the contained mica. Mica mining in the United States is confined largely to pegmatites and schists in a few well-defined areas. The largest region extends from central Virginia southward through western North and South Carolina, northern Georgia, and east-central Alabama.'" Whereas in western North Carolina, these pegmatite dikes are weathered to only a shallow depth, they are deeply weathered in the Carolina Piedmont and in Georgia and Alabama. Particularly in Georgia and Alabama, mica is found in the decomposed slates and schists adjacent to the pegmatites, and in deeply weathered granites. Most flake mica is obtained as the major marketable product by crushing and milling pegmatites4 To a lesser extent, mica is produced as a byproduct of feldspar" and spodumene. Past research by U.S. Bureau of Mines (USBM) has developed two methods for mica flotation. One method utilizes acid-cationic flotation for recovery of mica.' This method requires thorough desliming of the ore with consequent fine mica losses. The other utilizes an alkaline-anionic-cationic process for recovering fine-size mica from pegmatite ores after desliming sufficiently to remove clay materials but not so drastically as to remove the fine mica.8-18 The latter process has also been successfully applied to a micaceous schist ore from California.' This report summarizes the results of these research studies. Both of the flotation processes developed by USBM have been adopted by the mica industry and are being commercially utilized separately and in combination for flotation of mica from weathered pegmatite ores. Description of Ores The weathered mica pegmatite ores used in the investigations were obtained from commercial mica operations in Alabama, Georgia, and North Carolina. The

Jan 1, 1971

By J. S. Woodward, F. B. Plummer

The measurement of the rate of flow of liquids through sands dates back to 1856, when H. d Arcyb, a French physicist, carried out his classic experiments on the flow of water through sand layers. The earliest recorded data on relationships of pressure to flow of fluids through porous rocks in this country are those of Newell 23 in 1885. The first comprehensive studies of flow were made in 1898 by King15, who measured the rate of flow of water and air through consolidated and uncon-solidated sands and published the results. From 1900 to 1920 there appears to have been little interest in permeability. In 1920 the increase in demand for oil led the U. S. Bureau of Mines to begin a series of experiments to determine subsurface relationships of oil and water and the characteristics of their flow. Mills18 studied the relationship of flow of liquids to text- and structure of the sands, and Melcher17 in 1925 made a quantitative study of effect of changes in pressure on rate of flow of crude oil through Oklahoma oil sands. Since 1930 the importance of flow measurements to production of oil and gas has been emphasized by a large number of excellent investigations. Among these the works of Fettke9.10, BarbI.2, Cloud6, Nutting24-", Bot-set4, Nevin22, Tickell32.33, Fancher, Lewis and Barnes8, Moore, Schilthuis and Hurst19, and Wyckoff, Botset and Muskat"-39 have contributed much to our knowledge of the technique of permeability measurements and to the laws of liquid and gas flow through porous sands. The application of their work has led to the establishment of laboratories for measuring the permeability and porosity of oil sands by most of the large companies. All the investigations, except those of Wyckoff, Botset and Muskat, and Moore, Schilthuis and Hurst deal with linear flow; that is, flow in a more or less straight line through a given cross-sectional area of sand. Three years ago, at the University of Texas, experiments were started to measure radial flow of liquids through sands; that is, flow from all directions toward a central opening—the conditions that operate in a

Jan 1, 1937

THE morning session on mining methods with R. M. Raymond as chairman was devoted mainly to papers on explosives and the discussion of these papers. A paper on the numerical index of the re-sistance which rocks offer to the penetration of a drill bit was also read. The first paper, "Relation Between the Oxygen Bal-ance and Propulsive Strength of Eight Gelatin Dynamites" by G. St. J. Perrott, N. A. Tolch and J. E. Crawshaw, was presented by Mr. Perrott, super-intendent of the Pittsburgh Experiment Station of the U. S. Bureau of Mines. In this paper which is the beginning of a series of publications on explosives, Mr. Perrott stated that the attempt was made to put down in quantitative form the facts which have been known to explosive engineers for a long time. Eight samples of 40 per cent gelatin dynamite, with oxygen content varying from + 15 to - 36 per cent of the theoretical amount necessary to form complete combustion with all of the combustible elements were tested. The experimental work showed that a bal-anced explosive did not give the greatest propulsive strength-but the most favorable range was from - 8 to - 25 per cent oxygen. The experimental work also brought out the fact that the wrapper of a stick of dynamite enters quite completely into the explosive reaction, and gelatin dynamites from which the wrapper had been removed developed less strength than the a same explosive with the wrapper. The second paper, "Effect of Oxygen Balance of Gelatin Dynamites on the Gaseous Products of Det-onation," by G. W. James and G. St. J. Perrott, was also presented :by Mr. Perrott. The first portion of this paper is given over to a discussion of the relative merits of different types of apparatus for testing and analyzing the combustion products of dynamites. Three types were used (1) the Bichel gage, (2) the Crawshaw-Jones apparatus and (3) the Hercules tank. All three of these types were used in testing dynamites whose oxygen balance varied from-35 to + 6 per cent.

Jan 3, 1928

By R. Walker, R. J. Anslow

Today at Tampa we see the end results of a team effort: A vital link in an intermodal transportation system, the link that enables the unit-train concept to be employed with full effectiveness and the link that improves the economics of water transportation systems. Two new phosphate transfer complexes with a multi- million ton annual capacity are in operation in Tampa, Fla. Revolutionary in concept, these companion installations represent a total investment in the Tampa Bay area of $18.5 million.

Jan 1, 1970

By P. M. Robinson, M. B. Bever

The heats oj formation at 273°K of the compounds CdTe, I)z2Te, InTe, In2Te3. In2Te5, SrzTe, and PbTe have been rleasrred in a liquid metal solutiotz caloritrete? 1.t1itlz bismuth as solvent. The?, are iterpretecl in yelation to tlze stability and bonding of the cott/pozltzds. Tile heats of fusion atzd the melting- points of tlze cotlzpounds InTe and Itzz,Te3 1lcti.e been measured in a cotrslant-temperature gradient calorimeter. The entropies of fusion are disc,ztssecl in YIIIS 01. the degree of order in the solid at the melting point. THE heats of formation of the tellurides of cadmium, indium, tin, and lead have been measured as a continuation of research on the thermodynamic properties of compounds of tellurim.' The tellurides of these metals were selected with a view to examining the relation between the heat of formation and the position of the metal in the periodic system. The elements cadmium, indium, and tin are in the same period and tin and lead are in the same group of the periodic system. The tellurides of indium are of special interest because four compounds, In2Te, InTe, In2Te3, and InzTe5, occur in this system. The available information on the heats of formation of the compounds investigated consists of values for CdTe, SnTe, and PbTe derived from electromotive-force measurements,J a value for CdTe obtained by tin solution alorimetr, and values for InTe and In2Te3 determined by combustion calorimetry.5 These values, however, refer to various temperatures ranging from 273' to 673°K and some of the reported error limits are large. Liquid metal solution calorime-try may be expected to yield more accurate values for the heats of formation than electromotive-force measurements or combustion calorimetry. The heats of fusion and the melting points of the compounds InTe and In,Te3 were determined in a constant-temperature gradient calorimeter. No published information appears to be available on the heat of fusion of these compounds. The results reported here give an indication of the degree of order in the solid compounds at the melting point. 1) MATERIALS AND EXPERIMENTAL PROCEDURE Materials. Samples of the compounds SnTe and PbTe were obtained from the Westinghouse Research Laboratories and samples of the compound InTe from Lincoln Laboratory, Massachusetts Institute of Tech- nology. Additional samples of the compounds InTe, SnTe, and PbTe and samples of CdTe, In2Te, In2Te3, and In,Tes were prepared from 99.995 pct Cd (Baker Chemical CO.), 99.999+ pct In (American Smelting and Refining Co.), 99.99 pct Sn (Baker Chemical Co.), 99.999+ pct Pb (Fisher Scientific Co.), and 99.999+ pct Te (American Smelting and Refining Co.). Stoichiometric amounts of the component elements were melted in sealed, evacuated Vycor tubes. The melts were held at approximately 100°C above the liquidus for about 16 hr and shaken repeatedly. The melts of the compounds In2Te and InzTe5, which form by peritectic reactions, were quenched into iced water. The melts of the other compounds, which have congruent melting points, were slowly cooled to room temperature. The samples were then annealed for 5 days at approximately 50°C below their respective solidus temperatures. Metallographic examination did not reveal any evidence of second phases or segregation. At least two batches of each compound were prepared. Samples from each batch were used in determining the heats of formation and, in the cases of InTe and In,Te3, the heats of fusion. The Heats of Formation. The heats of formation at 273°K of the compounds were measured by metal solution calorimetry with liquid bismuth at 623" as solvent. In this technique, the heat of formation is determined from the measured heat effects on dissolution of the compound and of a mechanical mixture of the component elements. The difference between these heat effects adjusted for changes in the composition of the bath gives the heat of formation at the temperature from which the samples are added to the bath (273°K). The experimental technique and method of calculation have been described in detail elsewhere.= It should be emphasized that the reported heats of formation depend on the thermodynamic data used in calculating the heat effects for the calibration additions. In the present investigation, the calorimeter was calibrated by adding pure bismuth at 273°K to the bismuth bath at 623°K. The reported heats of formation are based on a value of 4.96 kcal per g-atom for the difference in the heat contents of bismuth at 623" and 273". If a new value for this quantity becomes available, the reported results may be adjusted in direct proportion. The concentration of solute in the bath at the end of a calorimetric run did not exceed 1.7 at. pct and was usually less. In this range, the heat effect on dissolution of the solute was a linear function of the concentration of solute. In determining the heats of formation of the compounds in the system In-Te, a few runs were carried out in which two neighboring compounds such as InTe and In,Te3 and the corresponding mechanical mixtures of the components were added to the calorimeter. The

Jan 1, 1967

By Robert E. Delavault, Harry V. Warren

Geochemistry in all its branches is playing G an increasingly important part in the business of mine finding. Although geochemical studies were commenced more than 50 years ago, interest in this subject did not become widespread until the late 1930's when in Scandinavia and the U.S.S.R. a whole series of investigations were initiated. Unfortunately for those in North America, the results of these investigations have only recently become available. In Canada and the U.S. geochemistry as a serious mine finding tool dates back only to the period following World War II. This article deals primarily with soils, which have found widespread acceptance as a useful tool in geochemical prospecting. Actually soils vary greatly in texture, structure, profile, and mineral background. Soil sampling poses no hardship for normal intellects, but it does assume an elementary knowledge of soil science and of the chemical problems involved in determining the absolute and relative amounts of a particular element in any particular soil.

Oct 1, 1956

By Brandon H. Grove

In Austria's only producing field, at Zistersdorf, Erdoel Produktions-gesellschaft completed a single new producer, its well Gosting 6 coming in early in October for an average production of about 15 tons daily. For further testing within the proved part of the field this company's Gosting 7 was at the close of the year drilling in Pannonian strata at 760 m., and its Gosting 8 was rigging up. Outside of the proved area of the Zistersdorf field two further tests located on the Steinberg dome failed to find production in the known oil-bearing strata of the Sarmatian, and were deepened as wildcats into the Cretaceous Flysch. The first of these, Neusiedel 1, about one kilometer north of the known producing area, found oil in the Flysch beds at a depth of 1290 m. for an initial production of about 10 tons per day. The second test, Windisch Baumgarten la, is an old well previously considered a failure, which when deepened achieved a production of about 5 tons per day in the Flysch Inoceramus beds at 985 m. Neither of the foregoing wells is producing from a stratigraphically definable horizon, oil accumulation in the Flysch of this area being apparently controlled by tectonic breccias or related crevices.

Jan 1, 1937

By S. J. McCarroll

Fig. 1—The belt shown at right carries filter cake to mixing station over calciner. Crude ore conveyors appear in right background. THE Three Kids mine, some six miles east of Henderson, Nev., is in a typical southwest desert area, with high dry summer heat and cool to cold winter seasons. The manganese deposit was located during World War I.' During this period 15,000 to 20,000 tons of ore assaying up to 41 pct manganese were shipped. Interest in the deposit was not revived until the middle thirties, when experiments on the ore were initiated. Test work indicated possible recovery of only 70 pct by flotation, but in 1941 additional work was done at the Boulder City pilot plant of the U. S. Bureau of Mines and also by M. A. Hanna Co. As a result, the Manganese Ore Co. was formed and a plant utilizing the SO2 process was constructed. Numerous operation difficulties ensued, and the plant. was closed when the manganese situation in the country eased. In 1949 Hewitt S. West initiated negotiations to acquire the plant. In 1951 Manganese, Inc., was formed and contract entered into with the General Services Administration to supply 27 million units of metallurgical grade manganese in the form of nodules to the national stockpile. A second contract was made to upgrade 285,000 tons of stockpile ore. Test work was undertaken by the Southwestern Engineering Co. and likewise by the Boulder City pilot plant at the U. S. Bureau of Mines. Results obtained indicated the commercial feasibility of the flotation process. Construction of the plant, which is shown in Figs. 1 and 2, was started in June 1951, and operations on a break-in basis began in September 1952. Apart from the usual starting difficulties two major disasters caused serious setbacks, one a kiln failure in February 1953, and the other a fire that destroyed the flotation building in June of the same year. The nodulizing section of the plant resumed operation in November, and the flotation section in January 1954. The ore minerals are chiefly wad,* with minor amounts of psilomelane, and occur in sedimentary beds of volcanic tuff. The ore is overlain with beds of gypsum which outcrop or may be covered with surface gravel. Intermediate beds of red and white tuff occur frequently with lenses of red and green jasper and stringers of gypsum and calcite. Small amounts of iron are present; lead content averages about 1.0 pct and minute amounts of copper and zinc are found. Barite, celestite, and bentonite are present. Since these are made up of minute asicular crystals, moisture content is very high, averaging about 18 pct. Ore reserves have been estimated at 3 million tons averaging 18 pct Mn2 and up to 5 million tons after grade is dropped to 10 pct Mn. A good part of the orebody was stripped of overburden by the previous operating company . Approximately 50 pct of the ore, representing more than 60 pct of the manganese, can be mined by open-cut methods. A system for underground min- . ing has not yet been decided on. Open-cut mining with benches of 20 ft has proved satisfactory. Although the ore is soft and appears dry and dusty it has a certain resilience, probably due to the porosity and moisture which makes drilling and fragmentation difficult. Wagon drills have been abandoned in favor of the Joy 225-A rotary drill which will put down a 43/4 -in. hole at the rate of 2 ft per min. Holes are spaced in a pattern with 8 to 9-ft centers. Forty percent powder has been used, but better breaking to 2-ft size is obtained with low velocity bag powder of 30 pct strength. Loading is done with one 21/2-yd shovel, and cleanup follows with one D-7 bulldozer. The ore is hauled with Euclid trucks about 1000 ft from the pit to a blending pile, where the daily mine production is spread in layers by bulldozing until approximately one month's mill feed is accumulated. A new pile is then started and mill feed is drawn from the first pile by one 13/4-yd shovel and Euclid trucks, with a haul of approximately 500 ft. Mining is performed by an independent contractor with engineering and supervision by the company staff. Early test work indicated that the manganese could be floated with soap, a wetting agent, and fuel oil to give a recovery of better than 75 pct with a grade of 43 pct Mn. The concentrate when nodulized with coke would upgrade to 46 pct Mn or over, and the lead volatilized to 0.6 pct residual.

Jan 1, 1955

In the seven years that have elapsed since the AIME World Symposium on Mining and Metallurgy of Lead and Zinc, there have been a number of significant milling innovations and trends implemented in lead-zinc flowsheets to either improve grade and recovery or to control escalating mill costs. First, mill controls and instrumentation, which only had a foot in the door in 1970, have become increasingly common. In Australia, research into automatic crushing control has been implemented by Mount Isa Mines, and in virtually any large lead-zinc mill worldwide, an assortment of on-stream x-ray analyzers, grinding circuit controls, level detection devices, and reagent metering methods can be found. The increased circuit control offered to mill operators by this new technology points to more efficient flowsheets, as well as to a greater dependence upon computer-controlled operation.

Jan 11, 1977

By J. N. Ong

The oxidation of tantalum is assumed to occur by four simultaneous first-order chain reactions; solution of oxygen in the metal, nucleation and growth of a suboxide phase at the metal surface and two phase boundary processes which give rise to two different modifications of Ta2O5. A rate equation is then formulated which accounts for all principal details of oxidation behavior, unifies and correlatss the results of the principal investigations, and expresses the rate as a function of pressure, temperature, and time. For purposes of practical application, the expressions: may be used below and above 700T respectively to determine the regression rate of tantalum in cm per hr, where T is to be expressed in "K and P in atmospheres pressure of oxygm. The equations will reproduce within a factor of two all reported experimental rates in the temperature range 475" to 1400°C and pressure range 0.000026 to 40.8 atm 0. 1 HE oxidation kinetics of tantalum have been investigated thoroughly in the temperature range 50" to 1400 and pressure range 1.32 x l0-' to 40.8 atm pressure of 0,and as a result, the principal features of the oxidation of tantalum are known and have been described in considerable detail. The exposition of the characteristics of the behavior of tantalum in oxygen has been largely descriptive, with considerable attention being devoted to elucidating the structure, composition, and morphology of the resulting oxide products. The weight change vs time results have usually been reported graphically. With the exception of the linear rate below 700 C and the process of diffusion of interstitial oxygen into the metal,6'9 no effort has been made to characterize the reaction rates in functional form. It is the purpose of this paper to demonstrate that when the fundamental principles of chemical kinetics are rigorously followed, the results of the principal investigations will be correlated and unified and the oxidation rale may be expressed as an analytic function of pressure, temperature, and time. In addition to accounting for the temperature and pressure dependency of the oxidation rate, the following minor features will be accounted for as a result of the basic analysis: the initial period of nonline-arity in rate at low temperatures, which decreases with increasing temperature;3'5'7 the rate vs temperature cusps obtained at constant pressure"5 the concentration gradient of oxygen interstitially dissolved in the metal.5'7 The analysis will also be consistent with the overall chemistry of reaction and with all visual, microscopic, and X-ray observations. DEVELOPMENT OF RATE EQUATION As a fundamental basis for the treatment of metal-oxygen reaction kinetics, it will be regarded that the rate of reaction is determined by the concentration and not the activity or chemical potential. It is further assumed that all metal-oxygen reactions are first order complex chain reactions" whose rate is dependent on the concentration of an intermediate species which is a complex function of the oxygen concentration, or oxygen pressure, only. The basic rate equation is therefore: is the weight of oxygen consumed by the reaction, A is that portion of the area of the metal over which the reaction is occurring (cm2), t the time (sec), kf the rate constant for forward reaction, C the intermediate species concentration and f '([Oz]) and f (Po,) are complex functions of oxygen concentration and Oxygen pressure respectively. Reverse reactions may usually be neglected in metal-oxygen systems since a large negative free energy generally accompanies these reactions. Eq. [I] takes different forms when the rate of reaction is controlled by diffusion into or through a phase or at a phase boundary. For diffusion into the metal phase, the rate is given by1' Di is the diffusion coefficient of species diffusing into the metal phase (cm2/sec), and Q is the corre-

Jan 1, 1962

By T. S. Lovering

Geochemical prospecting extends the age-old method of searching out lodes with a gold pan and rationalizes the prospector's hunch that certain plants are associated with ore. It uses sensitive but cheap and rapid analytical methods to find the diagnostic chemical variations related to hidden mineral deposits. Exploration geologists can gain tremendous assistance from this new tool, although its optimum use is not simple. To bring out the geochemical pattern that reveals the presence of a hidden ore deposit with a minimum number of samples requires a combination of shrewdness, chemical knowledge, and exploration geology. The use of sensitive analytical methods for prospecting had its start in the 1930's in northern Europe, where Scandinavian and Russian geologists had some success in these early efforts. Very little geochemical prospecting was carried on in the United States at this time, and no sustained interest was manifest until the close of World War II, when geochemical investigations were started by the Mineral Deposits Branch of the U. S. Geological Survey. The purpose of these investigations was to apply geochemical principles and techniques to surface exploration for mineral deposits. Both the research on analytical methods and the routine trace analyses for field investigations were at first conducted by a single group, but it later became apparent that the trace analyses could be done by men of less experience than that required for successful research on methods. For the past several years there have been two groups of chemists, and although their functions overlap, three of the chemists are chiefly concerned with research, while four to six other men make the trace analyses for field projects.

Oct 1, 1955

As knowledgeable men in the industry know, a mineral occurrence is found through prospecting but an ore deposit is "made" -made through, first, imaginative and effective exploration; thence through efficient engineering, sales and management. There are two main phases of exploration-reconnaissance and target investigation-each of which can be further divided into two additional stages (see accompanying table). The search for a new ore deposit within a known and geologically mapped mining district involves only the last two stages, whereas the search for a new orebody in a virgin geologic environment involves at least three stages and often the full sequence. Of course, some of the exploration stages may be bypassed depending on available results of previous mineral surveys and/or exploration by individuals, business concerns, and governments.

Jan 10, 1967

By R. W. Guard, M. E. Fine

By treating the dislocation like a surface and ap-plying the usual thermodynamic treatment to the adsorption process a Gibbs adsorption equation for dislocations was derived. For extended dislocations in binary solutions the adsorbed concentration on the fault, X2a, may be computed from (jo/da2b) where a2b is the activity of the solute in the bulk material and s is the stacking-fault energy. Using the data of Howie and Swann for s the adsorption concentration goes through a maximum at 2 at. pct Al in Ag-Al, 10 at. pct Zn in Cu-Zn, and 8 at. pct A1 in Cu-Al. The pinning stress calculated from this concentration difference goes Ihrough a maximum at the same concentration us the peak in X2 a. The computed pinning stress thus does not vary with composition in the manner predicted by Suzuki, as was also pointed out by Hendrickson. The results are compared with the stress increment which can be attributed to Suzuki locking in Cu-Zn and Cu-Al stress-strain curves. They both agree in magnitude and in the location of the maximum. The predicted and observed maximum values for the Cu-Zn system (where activity data are available) are 700 g per sq mm (predicted) and 1000 g per sq mm (measured, laking into account the orientation factor of 2.2 to convert poly-crystalline to single-crystal data). CERTAIN simple internal surfaces may be regarded as dislocation grids. This fact suggested that it might be profitable to consider certain phenomena related to segregation of solute atoms at dislocations from the point of view of the thermodynamics of surfaces and surface adsorption. A general treatment of this type is given and then the results are applied to Suzuki segregation and pinning. Confirmation of the results is obtained from comparison of stress-strain behavior for copper and copper-base alloys. Two kinds of dislocations need be treated: perfect and extended dislocations. In either case the line tension of a dislocation, ?. the work which must be done to increase the length of dislocation by a unit length, is analogous to the surface tension. For an undissociated dislocation ? is the self-energy of a unit length of dislocation; for an extended dislocation where is the self-energy per unit length of a pair of partials far enough apart so that there is no interaction energy, is the interaction energy per unit length, is the stacking fault energy per unit area, and w is the equilibrium separation of the paired partials. In the absence of an applied stress the force pushing the dislocation partials apart in a close-packed structure is Gb2/12p where G is the shear modulus, b is the Burgers' vector of the complete dislocation, and is the separation of the partials. At the equilibrium separation, w this force equals s. Thus

Jan 1, 1965

By Marling J. Ankeny

MINING research in the U. S. today is indeed complex, whether it involves the Government, a small private concern, or a large one. And it promises to become more so, despite great advances already made in developing equipment and technology. The U. S. Bureau of Mines is committed to place greater emphasis on mining research as expressed in a recent policy statement to Congress on the "Long Range Minerals Program," by Secretary Fred A. Seaton, quoted above.

Jan 1, 1958

By N. K. Chen, R. Maddin

Columbium single crystals were deformed in tension and compression. Reorientation by X-rays and stereographic projections of slip traces indicate that plane of slip may be considered as (110). The plastic behavior is shown to be quite similar to the deformation of molybdenum single crystals. STUDIES on the crystallography of the deformation process in body-centered cubic metals have been renewed recently with investigations of iron single crystals1-" and molybdenum single crystals.4 It is now apparent that too many exceptions to the rationalization based upon the ratio of absolute testing temperature to absolute melting point by Andrade5 exist to permit more serious discussion of this type of analysis. The considerations of resolved shear stress utilizing only planes of the type {ll0}, {112), and {123)³,6 permit analysis of the deformation only on the basis of those three types of planes. The suggestions made by Elam7 and by Greninger8 in which the slip process is envisioned as a composite slip on two nonparallel {110) planes can be illustrated schematically in Fig. 1. It may be seen that an unresolved trace on any plane containing a <111> direction may be accomplished by varying the number of atoms participating in the composite process. By further varying the number of atoms in each plane but keeping the ratio of participating atoms constant, jogs could be obtained in the traces and hence wavy slip lines could be produced. Vogel and Brick&apos; studied the behavior of a iron single crystals in which they suggest that the plane of glide is "non-crystallographic" and may be predicted from the intersection between the great circle joining the slip direction and specimen axis with the great circle whose zone axis is the slip direction. In a more recent investigation on iron single crystals, Steijn and Brick" suggest that the slip mechanism may be considered as made up of a type of composite slip occurring on {110} and {112} planes. Evidence for a possible composite nature of the slip process has been presented for the case of molybdenum in the form of analysis of asterism and specimen axis rotation." Definite proof of a composite slip process must, however, await good electron microscopic resolution of the individual traces making up the unresolved optical trace used in determining the acting slip plane. The present investigation was undertaken to study the behavior of columbium single crystals not only in tension but also in compression since the specimen axis migration should indicate the plane or planes of glide in the same manner that the specimen axis migration in tension indicates the direction of glide. The orientations of eleven crystals investigated are shown in Fig. 2. Specific orientations are missing (those in the vicinity of [Ill] and [001] and consequently the effect of orientation on the crystallography of deformation could not be considered. Experimental Procedure The 1/8 in. rods (7 in. long) were subjected to an axial tension in vacuo while at temperatures in the vicinity of 2000°C for 2 to 4 hr. This treatment resulted in large cylindrical grains (about ½ in. long) occupying the entire cross section. A number of these rods were used for the tension studies by observing the behavior of the individual grains. For the compression studies, single crystals approximately % in. long by 1/8 in. in diameter were cut from the rods; the ends were ground parallel. All specimens were polished electrolytically in a solution of 15 cc HF(48 pct) and 85 cc H2SO4 (concentrated) using a platinum cathode, a current density of 0.04 amp per sq cm and a temperature between 25" and 60°C.10 Orientations were obtained using a Laue back-reflection method (3 cm film to specimen distance) with a ½ mm collimator 9 cm long. For the compression specimens, a reference mark was scratched on one of the compression sur-

Jan 1, 1954

By William Sellers

tested without knowing anything of their chemical composition. I had these pieces separately placed upon 10-inch bearings under a 7-gross ton lianlrner, a piece of 2½-inch round iron laid upon them as a fuller, and the hammer allotved to fall from 20 inches above the fuller, which, according to Haswell, gave a ldow of 67.75 gross tons. The pieces were then turned orcr, the fuller placed upon the convex surface, and the harnnler allowed to fall from 13 inches above the fuller, giving a blow of 58.46 gross tons. You will see that the rails do aot show ally bigrls of ruptnre, and their color at the points of torture prove them to have been absolutely cold when the test was made. I thirk these rails ought to be reasonably safe in the track. As you see by this piece of the head of one of these rails, I had it plarred, and then some teeth cut in it by a cold clrisel, and one-half of them pounded down with a hammer. The teeth of my rack did not break off. The analyses of these rails substquently made are: I. 11. Carbon,... 0.110 0.880 Silicon,..0.050 0.058 Phosphorus ,..0.086 0.082 Manganese,.. 0.042 0 840 In conclusion, I will say that Dr. Dudley&apos;s paper as a contribu tion to our knowledge of steel rails is valuable and interesting, but I protest against his conclusions king reoeived as manufacturing or comtnercial axioms. From its being presented in the form-of a report to the leading railroad of the country from one of its trusted officers, as well as from the tone of the concluding deductions, it is liable to be so received by railroad men. If any railroad com pany desires rails made under either of Dr. Dudley&apos;s formulas, and are willing to pay a price large enough to cover the loss in making them, dl and good; but so long as the rail makers are compelled to gwrrantee the wear of their rails for a given number of years, justice reqnires that. the composition of the steel from which these rails are made should be left to them. WILLIAM SELLERS, PHILADELPHIA: The very interesting paper upon the wear of steel rails that has just been read preseak the record of a series of investigations that are extreniely valuable, and the deduction that bas been drawn from the results noted seems to be unavoidable; the tests, however, to which it is proposed steel rails shall be subjected hereafter, with a view to determine their quality, sllould

Jan 1, 1881

By P. M. Kelly

TWO analytical methods for calculating the positions of matrix and twin reflections on electron-diffraction patterns of a twinned cubic crystal have recently been published.1,2 Meieran and Richman1 considered the case of twinning on (1 12) in a bcc structure, while a more general treatment, capable of analyzing twinning on any plane in a cubic crystal, was developed by Johari and Thomas.2 The latter authors applied their general rotation matrix to both (111) twinning in face-centered crystals and {112} twinning in body-centered crystals and they derived separate expressions for these two cases. This separate treatment masks the fact that in a holosymmetric cubic crystal a (111) twin is crys-tallographically equivalent to a {112} twin.3 This is analogous to the crystallographic equivalence of rotation and reflection twins in centrosymmetric crys tals. A particularly simple example of this equivalence occurs when the two twin planes are perpendicular to each other—for example (111) and (112). Then, if twinning on (111) moves a point P to a new position P1, and twinning on (112) moves P to P2, P1 and P2 will be related to each other by a 180-deg rotation about [110]— the direction normal to both (111) and (112). Since there are diad axis axis along (110) direction in a holosymmetric cubic crys tal the two positions P1 and P2 must be crystallo-graphically equivalent. In other words if a particular pole (hk l) is in a position P1 after twinning on (Ill), then after twinning on (112) a pole of the type {hkl}—but not the particular pole (hk1)—will also be in the position P1. As a result, when only the general (as opposed to the particular) indices of poles after twinning are required, twinning on (111) gives the same results as twinning on (112). To convert the results for a (111) twin to those applicable to a (112) twin, when the particular (as opposed to the general) indices of poles after twinning are required, all that is necessary is to multiply the indices of the twin poles by the matrix for 180-deg rotation about [lie], i.e., The analytical methods suffer the disadvantage that a new set of calculations must be performed for each different diffraction pattern or, as is done in the Meieran and Richman treatment,1 a lengthy list of the location of the twin spots in reciprocal space must be prepared. All the tedious computation involved in these analytical approaches can be avoided by simply plotting, on tracing paper, a stereographic projection of a crystal twinned on say (112). By superimposing this twin stereogram on a standard (001) projection (preferably with the points and indices in a different color from those on the twin stereogram) the relative positions of both matrix and twin reflections can be determined by inspection. Alternatively, a composite projection can be

Jan 1, 1965

By D. E. Spiller

Introduction Precious metals recovery from ore can generally be accomplished using gravity concentration, flotation, and/or hydrometallurgical (leaching) techniques. The objective of this paper is to show why gravity concentration can be an important part of recovery systems that employ leaching as the primary unit operation. A brief discussion of modem gravity concentration equipment is also presented. Discussion Gravity concentration of ores has generated increasing interest in recent years. Reasons for this interest include: • Gravity concentration is environmentally attractive. There is little or no use of reagents. Hence, it is relatively nonpolluting. • The cost of cyanide has continued to increase. Therefore, cost savings may be realized whenever leaching feed tonnage can be reduced by preconcentration. • Compared to flotation and leaching, gravity equipment costs are low per processed ton. Field installation costs for gravity circuits usually are less because many&apos; units are supplied as self-contained modules. Also, the cost required to supply services, particularly power, to a gravity plant site are also less. In situations where preconcentration at coarse particle size is applicable, significant grinding equipment savings may be possible. • Gravity circuit operating costs are also relatively low compared to typical flotation and leaching circuits. Reagents, power, maintenance, and manpower savings in a well-engineered gravity plant may be realized. Again, if grinding is reduced, significant power and steel (media and liners) savings are possible. •In recent years, more efficient gravity concentrating devices have been developed. Benefits to Precious Metal Leaching Gravity beneficiation can complement precious metal leaching in two ways. First, the recovery of coarse liberated values before leaching may reduce leach time requirements and may reduce reagent consumption. Second, gravity preconcentration can reduce the size of a leach plant by decreasing the quantity of material to be leached. Coarse gold and silver have been shown to leach rather slowly. Kameda (1949) and Habashi (1967) have investigated the kinetics of cyanide leaching systems. They concur that in a heterogeneous reaction, the rate of gold and silver dissolution is directly proportional to the surface area. Thus, the instantaneous rate of dissolution for spherical 0.37 mm (400 mesh) gold is theoretically -25 times faster than for the same amount of gold at .841 mm (20 mesh), based on data from Fuerstenau, Chander, and Abouzeid (1979). Conversely, coarse liberated, +.841 mm (20 mesh), gold is more readily recovered by gravity concentration than is fine, -.037 mm (400 mesh) gold. Therefore, it is apparent that the two recovery systems complement one another. Figure 1 data demonstrates the potential synergism. A sample of - 3.327 mm (6 mesh) Nevada gold-bearing ore was cyanide leached using conventional bottle-roll test procedures. Gold extraction was determined as a function of leaching time. A second sample split from the same leach feed material was hand jigged to remove a coarse heavy mineral fraction, including virtually all of the +.210 mm (65 mesh) liberated free gold. This second sample, with the coarse gold and heavy minerals removed, was subjected to an identical cyanide leach procedure. Figure 1 presents the resulting comparative extraction data. Note that the percent gold extraction for the sample containing no +.210 mm (65 mesh) free gold includes the coarse gold recovered by gravity. The data show that the sample containing coarse gold required about 72 hours of leaching time to achieve 80% extraction. This compared to about 22 hours of leaching time for 80% gold recovery from the sample that contained only -.210 mm (65 mesh) free gold. Thus, there was a 69% reduction in leaching time. The improved extraction data is not wholly attributable to coarse gold removal, but rather it was the combination of gold removal and rejection of other heavy mineral cyanide consumers or leach retardants. Further investigation was not warranted at this time. Preconcentration is the second manner in which leaching systems can benefit from gravity concentration. The premise is that preconcentration can reduce the quantity of leach feed, which, in turn, may reduce leaching costs. Figure 2 presents preliminary data developed by CSMRI for US Minerals Exploration (USMX). Centennial Exploration Inc., in agreement with USMX, is proceeding with evaluations to determine the suitability of various processing schemes for recovery of gold values from the Montana Tunnels property. The data shows how the ore can be preconcentrated by gravity techniques to result in a reduced feed tonnage to secondary extraction techniques, presumably flotation or cyanide leaching. Testing has shown that Reichert cones, followed by treating the cone concentrate on spirals, can deliver about 88% gold recovery in about 13% weight, that is, 87% weight rejection. Consequently, fine grinding and reagent costs are attributable to only 13% of the plant feed rate. Cost data is not yet available, but the potential exists for significant cost savings.

Jan 1, 1985

By H. Foster Bain

THE "miracle of production." which was such an essential element in winning the European war, was nowhere more in evidence than in our Western States. In shipbuilding alone the Pacific Coast States -et a mark never before equaled, and in production of war goods of many kinds, both Rocky Mountain and Coast States accomplished more than their proportionate share if measured by population standards. This was only possible because of the building of immense new plants of many types, largely financed with Government money. Their operation has built up payrolls in the West and brought a measure of prosperity which Westerners are naturally anxious to have made permanent. A widespread doubt obtains, however, throughout the nation and even in the Western States themselves, as to whether, and if so to what extent, this may prove possible. The question has been raised as to whether the national treasury has not been raided to stock the Western ranges with a voracious breed of white elephant .

Jan 1, 1945