Search Documents

By R. N. Thurston, E. A. Nesbitt, G. Y. Chin

A general relalionship between the amount of glide shear (due to slip) and the macroscopic shape change has been developed. Since the deformation can be large, finite strain analysis is employed. In this treatnzent, the shape change is expressed by a deformation gradient matrix, F - [axi/aXj1, where X and x refer to the initial and final positions of a particle. This matrix is readily evaluated in terms of the amounl of glide shear, a , and the direction cosines of the slip-plane normal and the slip direction for a single active slip system. In the case of deformation from slip on several systems, the product F(a) of the several deformation gradient matrices is first calculated. Then, by assuming that the final configuration is reached by a long series of small shears of magnitude a, occurring more or less alternately in the several slip sys- IN problems of crystal plasticity, it is often necessary to relate the amount of glide in the operating slip systems to the macroscopic strain components. This relationship is relatively simple when only small strains are considered. In this case the separate strain contributions from several slip systems are additive. Such a procedure is incorrect in the case of large plastic deformation. To the authors' knowledge, no general treatment of the latter problem has appeared in the literature. In specific instances, Mark, Polanyi, and schmid3 have derived the relationship between glide and axial elongation during tensile pulling of a single crystal when only one slip system is active. A similar relationship for duplex slip was worked out by v. Goler and Sachs.4 Taylor and Elam5 have also studied in detail problems of large plastic deformation. Due to uncertainties as to the slip systems at the time, terns, the final deformation gradient matrix can be obtained. Mathematically, the problem is reduced to finding the limit of F(dN as N — m while a — 0 in such a way that the Product Na = 0, a ftnite conslant designatzng the accunzulated amount of shear. It turns out that this limit is simply , where F, is the matrix whose elements are the coefficients of a in the F(a) matix. Application is made of the present treatment to a fcc crystal of Perlrzalloy compressed on the (110) plane and contrained to elongate zn the [112] directzon. In addition, it is shown that one rnay readily obtain from the general analyszs the well-known formulas relating elongation, amount of glide shear, and amount of lattice rotation for crystals deforming by single and double slip under tension. however, they were mainly concerned with proving that slip occurs on {111}(110) systems in fcc metals. The present general treatment arose out of recent investigations of magnetic anisotropy in cold-worked Fe-Ni alloys6 as well as some related problems in strength anisotropy of single crystals.' Detailed application of the general analysis will be provided in the case of a Permalloy single crystal compressed on the (110) plane and constrained to elongate only in the [112] direction. It will be seen that, as expected, the small strain approximation leads to significant errors after moderate straining. It will also be shown that the present general treatment yields the formulas of Mark et al. and of v. Goler and Sachs in those specific cases. GENERAL CONSIDERATIONS Consider a homogeneous deformation in which a material point initially at moves to both positions being referred to the same set of Cartesian axes. Such a deformation can be

Jan 1, 1967

By Reynold Q. Shotts

The small domestic underfeed stoker as now designed is unusually sensitive to the coking and plastic properties of coals, and when the attempt is made to burn the high rank coking and caking coals of the Appalachian fields, serious trouble may occur. Part of the trouble may be caused by the ash content and clinkering characteristics of the particular coal in use, but more often it is the result of an excessive ac-in of coke in the form of ''trees,, or masses in the fuel bed. Often the zone of burning becomes so restricted that the fire goes out, and in extreme cases the fire may be lifted completely out of the fuel bed and away from the air ports. Even if the fire is preserved, excessive coking may cause response to subsequent heat demand to be slow and irregular. Coke trees seem to grow most readily during periods of hold-fire operation, so that in order to preserve the fire in mild weather it is often necessary to set the timer for such a long operating period each hour that much unneeded and unwanted heat is developed, causing discomfort. During demand periods the fire may pick up so slowly that the intense burning which develops just before stoker cut-off causes a serious overshooting of the thermostat. Stoker coal performance tests which have been made in a number of labora- tories1,2,3,4,5 are one method of approach to the problem Of selecting stoker coals- As yet these tests have not been standardized and they are expensive and time-consuming. The value of the results probably increases with the length of the test. Sherman and co-workers at Battelle Memorial Institute believe that even a one-week test is not too reliable a trial2 and it is quite likely that Others will agree. A great advantage of such tests is that characteristics of coals, other than the tendency to form coke masses, may be evaluated from them. The selection of stoker coals would be greatly facilitated if there existed some simp1e measure Of the tendency Of a a to form coke in a fuel bed. Although possessing all Of the disadvantages Of any small-scale laboratory test, the test for the free-swelling index of coal has been found useful for evaluating the probable effects Of swelling properties upon combustion.7 Ostborg, Limbacherand Sherman, have shown that the test can Predict, roughly, the tendency Of coke to accumulate in the fuel bed Of a domestic stoker. They also gave instances of its value in predicting combustion behavior in some large installations. The use of the test for free-swelling index has become well established and has been adopted as a standard by the American Society for Testing Materials.8 When domestic stoker coal investigations began at the State Mine Experiment Station in the summer of 1944, it was decided

Jan 1, 1949

By Benjamin Smith Lyman

THE importance of topography to geology is so commonly underrated as to deserve to be pointed out again and again. The relation of topography to the different branches of geology may be seen best by a glance at them all. Geology is well understood to consist of the observation of facts about rocks as materials of the earth (geognosy ), and the explanation of those facts (geogeny). The facts to observe are: I. GEOMETRICAL, as (1) structure, including the dip and strike at different points, the size, shape, and position of basins and saddles; (2) vertical section, that is, the thickness of rock groups and of their parts ; (3) horizontal or geographical position. II. PHYSICAL, such as texture, whether sedimentary or crystalline ; and, if crystalline, whether granitic, porphyritic, amygdaloidal, globular, or concretionary; whether compact or granular; coarse or fine; pervious or impervious; hard or soft; firm or tender; with cleavage or without; massive or thin; the microscopic structure; also whether magnetic or not; soluble or insoluble; fusible or infusible; and the constituent minerals. III. CHEMICAL, that is, the composition of the rocks and of their minerals and their affinities. IV. PALÆONTOLOGICAL, as what kind of fossils are in the rocks,

Jan 1, 1873

By A. M. Gaudin, C. S. Chang

IN general, fatty acids or their alkali salts do not cause clean quartz to float. However, the presence of multivalent ions, such as the alkaline-earth metal ions and heavy-metal ions, can activate quartz and thus make it respond to soap flotation. The mechanism of activation and soap flotation of quartz has been studied.1-4 The problem was attacked by making flotation tests rather than by careful adsorption measurements on suspensions of ground quartz in solutions containing the activator and the collector. Attempts have been made to determine the adsorption of barium ion and calcium ion on quartz. The results have only qualitative value as the analytical methods were not adequately precise. Artificial radioactivity and progress in radioactivity detection have introduced a new analytical tool, which can have a sensitivity several orders of magnitude greater than that of other methods.5-6 In the experimental work described in this paper the radioactive tracers, barium 140 and carbon 14, were employed. Lauric acid was synthesized, having a radioactive carbon atom and was used with Ba140 to study the adsorption of barium and laurate ions from aqueous solution on ground quartz. Flotation tests, using the vacuum flotation technique,4 were run in conjunction with the adsorption experiments. The object of this investigation was to understand better the reaction mechanism of barium activation and soap flotation of quartz. Methods and Materials Quartz Sample Preparation: Lumps of hand picked quartz, washed free of stains, were reduced in size to -20 mesh in laboratory crushers. The product was boiled in concentrated hydrochloric acid to remove the abraded iron. The cleaned product then was ground dry in a laboratory porcelain mill, using siliceous pebbles, to pass through a 200 mesh screen. The ground product was deslimed by sedimentation at 37 microns. This -200 mesh +400 mesh material was subjected again to boiling with concentrated hydrochloric acid, followed by washing with distilled water and further desliming. The cycle was repeated until no trace of iron could be detected in the wash liquor. During the final washing, the pH of the wash water was checked to insure the complete removal of the acid from the mineral. The quartz then' was rinsed with conductivity water. The resulting product was dried in a drying oven and stored in mason jars. The impurities (spectrographic) were as follows: Al, 0.01 to 0.001 pct; Li, Mg, Mn,, Na, each less than 0.001 pct; Fe and Cu not detected. The specific surface of the quartz sample was determined by the krypton gas adsorption method.7 The average of two measurements was 881 sq cm per g. The calculated specific surface for 37/74 micron quartz particles, using a surface factor of 1.96,8 is 900 sq cm per g. This is in good agreement with the measured value of 881 sq cm per g. Beta-Counting Method: The radioactive isotope of barium used in the experimental work was barium 140. It has a sufficiently long half-life, 12.8 days, emits high-energy beta particles (up to 1.0

Jan 1, 1952

By Peter L. Raffo, Walter R. Witzke

RHENIUM has a melting point of 5750°F, the second highest value among the metals.1 Its refractory nature should thus make it a useful material at high temperatures. The only available data on the high-temperature properties of bulk rhenium are from the work of Flagella and Tarr.2 These authors have shown that, over a wide range of temperatures and stresses, no appreciable linearity exists in a log-log plot of the minimum creep rate or rupture life vs stress. The purpose of the present letter is to describe some exploratory experiments designed to study the creep rate-stress-temperature relation and other facets of the creep of rhenium. The tests were carried out in vacuum in the temperature range 2200" to 4000°F (0.43 to 0.72 Tm,) at stresses ranging from 4 to 20 ksi. The powder metallurgy rhenium was purchased as 0.04-in.-thick sheet. The sheet is nominally 99.97 pct pure with the major impurities being iron (70 ppm) and molybdenum (25 ppm). The sheet was machined into specimens having a 1-in. gage length and a 0.25-in. gage width. The specimens were preannealed in hydrogen at 3000°F for 1 hr. This treatment produced

Jan 1, 1970

By Noel H. Stearn

OF the many instruments devised for the measurement of magnetic anomalies, the ordinary dip needle, by virtue of its superior simplicity of construction, facility of manipulation, and definiteness of interpretation, seems to merit serious attention as the instrument most readily applicable to the detection of magnetic anomalies of the higher order of magnitude. In spite of the fact that it has been used for many years for the discovery of iron ore in Europe and in the Lake Superior region of America, its capabilities as a geological instrument have not yet been thoroughly plumbed. The Wisconsin Geological Survey, under Dr. W. 0. Hotchkiss, E. F. Bean, and H. R. Aldrich, has been most thorough in developing the technique of the instrument, and the results it has obtained have aroused a general interest in a more widespread use of geomagnetics as an exploration method and the dip needle as a geological instrument. The simplicity of the instrument is an especial advantage, as it can be used by anyone, regardless of his technical training; but to insure useful results not only is a knowledge of the background of geomagnetics necessary but also an understanding of the principles of the instrument itself. Principles of the Dip Needle The major feature of the dip needle is an elongated magnet suspended with fixed bearings in such a way that it can move in a single plane. If the point of suspension were exactly at the center of gravity of the magnet, the instrument would be identical with the "dip circle" or "dipping needle" of terrestrial magneticists, and as such could be used to determine variations in the inclination of the earth's magnetic field when observed in the plane of the magnetic meridian. The dip needle, however, differs from the "dip circle" or "dipping needle" in having an adjustable counterweight affixed to one end of the magnet. This counterweight serves to balance the magnet at an angle to the inclination of the earth's field when the instrument is oriented in the plane of magnetic

Jan 1, 1929

FOR twelve successive years Canada's mineral production has shown a steady increase, rising from a value of $0.5 billion in 1945 to $2.06 billion in 1956, and the outlook for the future is one of continued growth. A great deal of credit for this growth must go to Canada's tax policies, which recognize that mines are difficult and costly to find, and that once found, they are a wasting asset. These tax policies take form under the Income Tax Act, which provides a tax- free period of three years on initial production for new mines and, after that period is over, allows all proper expenses of operation to be deducted from mine revenue. These allowable expenses include write-off of plant and pre-production development expenditures. From the resulting profit figure after this procedure, a further deduction of one-third is allowed for depletion before net taxable income is arrived at. Tax rates of 20 pct on the first $20,000 and 47 pct on the excess are then applicable to the net taxable income.

Jan 12, 1957

By E. Buehler, J. E. Kunzler

High-pu.1-ity molybdenum has been heat treated, melted, and zone refined and the physical and chemical changes that are produced by these processes have been studied by making resistance ratio measurements. Pronounced effects are observed that are associated with recrystalliza-tion at about 1200°C and with melting. Melting alone is found to result in a substantial purification by the evaporation of impurities such as iron. Zone refining is found to be reasonably effective with four passes producing a three-fold decrease in resistance ratio and a minimum ratio of 0.0003. With the aid of low temperature measurenzents, it has been shown that the build-up of a deposit of the material being zone refined on the radio frequency coil used for heating can lead to contamination of the sample. CONSIDERABLE interest in high-purity refractory metals for the study of mechanical properties has developed during recent years. Also the need for highly pure metals in certain fundamental studies, such as electronic band structure, has become quite widely appreciated. Molybdenum can now be produced with sufficiently high purity to make it attractive for such investigations. The most suitable measure of chemical purity of metals used for many of these studies is its resistance ratio, R,.,o,/Ro, During the purification of molybdenum by zone refining and its subsequent evaluation by this technique, a number of informative observations were made. These observations concern the effectiveness of zone refining, the volatilization of impurities at the melting point, and the recrystallization of molybdenum and appear to be pertinent to other refractory metals. Also, the usefulness of low-temperature resistance measurements as an analytical tool for evaluating the presence of chemical impurities and physical defects in metals is again illustrated. Samples of high-purity molybdenum of known mechanical history were heated to various temperatures between 800°c and their melting point. Resistance ratios of the samples were measured after they had been given a specified treatment. The data were used, along with mass spectrographic analysis, as an aid in interpreting the nature of the processes that occurred in conjunction with each treatment. Changes in the concentrations of chemical impurities and physical defects are typical of things that effect the low-temperature resistivity. SAMPLES The starting material was obtained from Westing-house Corp., Bloomfield, N.J. It was in the form of molybdenum rods, usually 1/8 or 3/16 in. in diameter. These had been previously processed from bars, 5/8 in, in diameter, originally reduced from 4 in. diam arc-cast ingots, by hot swaging at about 1300°c. In the final step, the temperature was lowered to about l lOO°C which resulted in the production of elongated grains. Typical grains were about 0.03 mm thick and 0.6 mm long. The molybdenum was quite pure as is indicated by the results of mass spectro-scopic analysis1 given in Column 2 of Table I. Other nongaseous elements not listed in the table were not detected. ZONE REFINING AND THERMAL TREATMENT OF SAMPLES Several sample rods, 8 to 10 in. long, were zone refined or were heat treated at several temperatures. Both types of operations were performed using 3 me-

Jan 1, 1962

By W. J. Tait, A. E. Craig, E. P. McCurdy

C. M. Marquard—The problem of the automatic control of a grinding-classification circuit is not nearly as simple as has been indicated and it cannot be universally solved through the application of this device. The sound emanating from a ball mill such as the metallic clink of the balls against the liners can at times be misleading. The fact that the sound level due to the balls hitting the liners may be at a minimum does not necessarily mean that the mill is properly loaded. I have in mind an ore we treat that has a soft talcy gangue. The soft fluffy nature of this material makes the sound from the ball mill a most misleading parameter that is worthless as a means for controlling the amount of ore fed to the mill. In every milling plant there are transportation lags due to the time it takes the ore to travel from the mill bins to the ball mill. In many plants there may be several different transportation lags due to varying distances of bins from ball mill. These transportation lags can most seriously affect the operation of a controller. It has been found that under many circumstances the transportation lags can be so bad as to cause the controller to hunt seriously. Hunting can and in many cases does become so serious as to render automatic control impossible because of the surges it causes. While it is possible to compensate for this type of lag, this apparatus does not lend itself readily to accomplish the required compensation. Further, if there are groups of bins at various distances from the ball mill, compensation for one may not be sufficient or may be too great for another. Each milling plant presents a separate problem. The apparatus as presently described does not appear sufficiently flexible to accomplish this. It should be noted that the load on the classifier rakes is determined by measuring the current input to the rake drive motor. Variations in line voltage will

Jan 1, 1951

By E. P. McCurdy, W. J. Tait, A. E. Craig

C. M. Marquard—The problem of the automatic control of a grinding-classification circuit is not nearly as simple as has been indicated and it cannot be universally solved through the application of this device. The sound emanating from a ball mill such as the metallic clink of the balls against the liners can at times be misleading. The fact that the sound level due to the balls hitting the liners may be at a minimum does not necessarily mean that the mill is properly loaded. I have in mind an ore we treat that has a soft talcy gangue. The soft fluffy nature of this material makes the sound from the ball mill a most misleading parameter that is worthless as a means for controlling the amount of ore fed to the mill. In every milling plant there are transportation lags due to the time it takes the ore to travel from the mill bins to the ball mill. In many plants there may be several different transportation lags due to varying distances of bins from ball mill. These transportation lags can most seriously affect the operation of a controller. It has been found that under many circumstances the transportation lags can be so bad as to cause the controller to hunt seriously. Hunting can and in many cases does become so serious as to render automatic control impossible because of the surges it causes. While it is possible to compensate for this type of lag, this apparatus does not lend itself readily to accomplish the required compensation. Further, if there are groups of bins at various distances from the ball mill, compensation for one may not be sufficient or may be too great for another. Each milling plant presents a separate problem. The apparatus as presently described does not appear sufficiently flexible to accomplish this. It should be noted that the load on the classifier rakes is determined by measuring the current input to the rake drive motor. Variations in line voltage will

Jan 1, 1951

By L. L. Wyman

THE resultant embrittlement caused by the exposure of oxygen-bearing copper when hot and exposed to reducing gases has been the subject of many studies.1 Little attention, however, has been given to the possible embrittling effects due to atmospheres or conditions that under some circumstances might be the source of a reducing gas. At rather infrequent intervals there occur reports of copper becoming embrittled during normal annealing cycles in commercial steam-atmos-hered furnaces such as customarily are used for this operation. As might be expected, several other factors exist-such as oil, dirt on the wire, or in the furnace, or metallic surface contacts that might produce reducing gases and be the source of the trouble. However, in consider-ation of the statement made by Ruder,2 it would seem that under some conditions steam itself might prove to be the source of trouble. A consideration of the amount of the dissociation of water vapor up to temperatures of the melting point of copper shows that' the amount of hydrogen that could come from this source is far too minute to account for any embrittlement. What such information does not tell is what will happen at the surface of copper when subjected to steam at elevated temperatures, for entirely different conditions may persist, which would account for Ruder's observation. Furthermore, there are no data as to what might happen at the surfaces of other materials present, the result-ant of which might affect the condition of the copper present. For this reason, it was decided to make a series of experiments com-parable to those previously conducted by the writer,1 which would clarify the effect of the steam on copper, and in copper in the presence of steel.

Jan 1, 1940

By E. P. Chartkoff, W. P. Sykes

In 1926 one of the authors published researches on the determination and description of the iron-tungsten and iron-molybdenum systems,' including the equilibrium diagrams. In 1929, further work was carried on, including the examination by X-rays, which is recorded here. Meas-urements were made of changes in lattice parameters in the solid solutions. Precipitation from the solid solution and the accompanying changes in hardness were studied as well as the formation of the intermetallic com-pound phases upon sintering a mixture of metal powders. Materials All the specimens were prepared from the same quality of metals and by the same methods as were described in the determination of the constitutional diagrams. The metal powders as mixed and pressed were sintered or fused in a hydrogen atmosphere and subsequently treated as indicated in the titles of the figures. The formation of the iron-rich solutlon in the solid was accomplished by sintering in hydrogen for a period of 20 to 30 hr. at a temperature 25' to 50' C. below the melting point of the eutectic. The tungsten-rich and molybdenum-rich solid solutions of iron were prepared by adding the iron as a solution of iron ammonium oxalate to the oxide of tungsten or molybdenum, followed by a hydrogen reduction. This method results in a homogeneous alloy after sintering the pressed metal powder for 20 to 30 hr. at a temperature slightly below that of the peritectic reaction in the system involved. For X-ray examination the specimens were variously prepared, depending on the nature of the sample and what it was desired to show. For example, the iron containing tungsten or molybdenum in solid solution was cut with a file, the chips were put through bolting cloth, and this powder of filings formed the specimens for comparative study. The

Jan 1, 1930

By H. H. Hasler

THE mining and removal of coal from two or more beds, either simultaneously or consecutively, in vertically adjacent areas have always been matters of concern to mine operators from both operating and recovery points of view. However, with the progressive introduction and use of electrical and mechanical facilities, such problems assume even greater proportions. In this paper typical cases occuring in Cambia County, Pa., are given and procedures whereby such problems may be .greatly reduced, if not entirely eliminated, are suggested. Throughout a considerable portion of the Central Pennsylvania bituminous coal region, particularly in Cambria County (Fig. I), the portion of the region to which references in this paper are made, large areas are encountered where two or more beds of coal occur and have been mined extensively since the earliest days of mining in the county. Generally, operations were commenced in one bed of coal on a property, following which, as conditions appeared to warrant, operations were commenced in another bed or beds on the same property, in some instances by the same operator. Operating results by no means have been uniformly successful, as the following review of some typical cases indicates, partly because of lack of experience in earlier cases and in certain later cases to disregard for the experiences of earlier operators. It is suggested that repetitions of such failures may be reduced largely, if not eliminated entirely, by adherence to a few basic principles founded upon past experiences. Geology and Stratigraphy The geology, stratigraphy, and relief of almost all of Cambria County have been studied and reported at length by the U. S. Geological Survey in its Johnstown, Ebensburg and Barnesboro-Patton Folios and other publications, by the Pennsylvania Geological Survey and by various individuals. All exposed rocks occurring within the boundaries of the county are of sedimentary origin, consisting of alternate beds of sandstone, slate, shale, fireclay, coal, limestone, etc., and all have been classified by the U. S. Geological Survey as extending from the upper strata of the Catskill formation, Devonian system, to and including, in a few hilltop areas, the lower strata of the Monongahela formation, Carboniferous system. Included within that range is the Allegheny formation, Pennsylvania series, which embraces all of the commercially important beds of coal that occur in the county, viz., the A, or Brookville, to the E, or Upper Freeport, both inclusive, shown in Fig. 2. The measures are traversed by a series of anticlines and synclines, extending in a northeasterly and southwesterly direction, which form broad, gently sloping basins (flat to 15 pct pitch, exceptionally to 25 pct). However, the topography of the surface is such that long lines of outcrops of all beds of coal overlying bed B, and to a limited extent bed B also, occur over large areas, a factor which contributed to the early and extensive development of mining activities in the county. Earliest mining developments of commercial importance were made in B, C', D, and E beds of coal, and it is in these beds that the principal mining operations are being conducted. To a limited extent, mining operations also have been conducted in local areas in the A, B rider and C beds. Coal beds being mined today range in thickness from approximately 28 to 60 in. Intervals between the respective beds of coal are variable but conform somewhat to the following general averages: A to B, 60 to 100 ft.; B to C, 50 ft.; C to C', 70 ft.; C' to D, 45 ft.; and D to E, 45 ft. The following are typical mining cases obserced over a period of years in various parts of the county.

Jan 1, 1952

By James W. Wade

THIS discussion of the future supply of lead refers only to the next ten-year period. Beyond that no prediction can be made that would be of sufficient accuracy to serve any purpose. When any commodity is by an unsatisfied demand forced to a higher price level, and the profits of those who are able to produce the commodity are greatly increased, there is awakened a new interest in the commodity on the part of both producer and consumer. The consumer attempts to reduce his costs by developing substitutes or assisting in the development of new sources of supply. Lead is now going through this stage. The lead producer is increasing development expenditure and searching for new mines. The consumer is developing substitutes as illustrated by the increasing use of zinc oxide as a pigment, and the use of dry batteries in radio sets. The search of the Ford interests for lead, by prospecting in Missouri and Idaho, is induced by the effort to develop a new source of supply. Considering the index figures of the Department of' Commerce, it is evident that lead is on a substantially higher price level. For February, 1926, the index figure of lead is 209, while the general commodity price index is only 156, 100 being taken as the base for 1913.

Jan 1, 1926

By R. J. Corfield

MODERNIZATION of the entire electrical system and improvement of Rotation process efficiency is the twofold goal of the improvement program underway at the Arthur and Magna concentrators of the Utah Copper Div., Kennecott Copper Corp. Copper ore from the Bingham pit goes to these two concentrators where an interlocking program calls for complete electrical modernization and increased flotation process efficiency through additional capacity and flow scheme revisions. Flotation plants at the two mills are essentially duplicates, and while this article deals with the changes at the Arthur mill similiar improvements are being made at the Magna mill.

Jan 3, 1953

By Paul Hett

The much-heralded Deep Ruth operation of Kennecott Copper Corp., at Ruth, Nev., is scheduled to become a producer by 1957. Inaugurated as a project in 1951, production was originally scheduled to start in 1953, but excessive water hindered shaft sinking. A revised schedule called for output by 1955, but again plans had to be changed. This time the change was to permit mining of an orebody that would have otherwise been lost because of block caving methods planned for the main deposit. The new ore is within the cave limits of the larger orebody, above the first production level. Ore will start coming from this new source in 1956, a year ahead of the principal operation. (See NEWS, page 344.) There is little doubt that current economic conditions and unforeseen expenditures for early shaft development will make the Deep Ruth a high-cost producer. Yet, some of the drawbacks of the Kennecott operation may be mitigated by the possibility that additional exploration will increase the already assured 25 million tons of 0.83 pet copper ore. While Kennecott is missing out on the current high copper market and is thus left with a potentially narrowed profit, the predicted demand for copper has created an optimistic feeling. Its development is certain to enlarge known U. S. copper reserves and significantly extend the life of Kennecott's Nevada operations.

Jan 4, 1955

By T. M. Morris

G. L. Simard and D. J. Salley—The authors and ourselves" independently came to similar conclusions both as to the value of tracer methods for the study of flotation and the general nature of collector-mineral interaction. The dodecylamine-quartz system appears to be simpler than the dithiophosphate-galena one, and the results therefore appear clearer. It is evident from a comparison of the two papers, however, that care must be used in extending the results to other more complicated systems. In the case of dodecylamine-quartz, the possible influence of micelle formation is of interest. There is no a priori reason why complete monolayer formation should necessarily occur at the concentration for micelle formation, since sorption depends on the nature of the substrate as well as on the properties of the solute in solution which alone determine micelle formation. Indeed, the fact that the onset of increased adsorption, point B in fig. 2, occurs at a concentration one tenth the critical value for micelles might imply that micelle formation does not have an influence. Interestingly enough, the data may be handled by the methods used for multilayer adsorption of gases on surfaces. Thus, if the amount adsorbed is plotted versus concentration, a sigmoid type curve is obtained, similar in form to a so-called Type I1 isotherm13 generally attributed to multimolecular adsorption. A monolayer value of about 0.12 mg per g may be estimated from the knee of this isotherm. On the other hand, if a plot is made according to the multilayer gas equation for adsorption to an unrestricted number of layers, eq 38,13 assuming the critical micelle concentration as the saturation concentration, the data above 120 mg per liter fall on a straight line from which a monolayer adsorption of 0.3 mg per g results. These considerations suggest that the monolayer may occupy an area somewhat less than the geometric value of 0.4 mg per g, and that micelle formation may indeed be a factor in the adsorption. the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By T. M. Morris

G. L. Simard and D. J. Salley—The authors and ourselves" independently came to similar conclusions both as to the value of tracer methods for the study of flotation and the general nature of collector-mineral interaction. The dodecylamine-quartz system appears to be simpler than the dithiophosphate-galena one, and the results therefore appear clearer. It is evident from a comparison of the two papers, however, that care must be used in extending the results to other more complicated systems. In the case of dodecylamine-quartz, the possible influence of micelle formation is of interest. There is no a priori reason why complete monolayer formation should necessarily occur at the concentration for micelle formation, since sorption depends on the nature of the substrate as well as on the properties of the solute in solution which alone determine micelle formation. Indeed, the fact that the onset of increased adsorption, point B in fig. 2, occurs at a concentration one tenth the critical value for micelles might imply that micelle formation does not have an influence. Interestingly enough, the data may be handled by the methods used for multilayer adsorption of gases on surfaces. Thus, if the amount adsorbed is plotted versus concentration, a sigmoid type curve is obtained, similar in form to a so-called Type I1 isotherm13 generally attributed to multimolecular adsorption. A monolayer value of about 0.12 mg per g may be estimated from the knee of this isotherm. On the other hand, if a plot is made according to the multilayer gas equation for adsorption to an unrestricted number of layers, eq 38,13 assuming the critical micelle concentration as the saturation concentration, the data above 120 mg per liter fall on a straight line from which a monolayer adsorption of 0.3 mg per g results. These considerations suggest that the monolayer may occupy an area somewhat less than the geometric value of 0.4 mg per g, and that micelle formation may indeed be a factor in the adsorption. the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By C. G. Albert

The clay particles of 2 microns or less required for modern paper coating are predominantly flat plates, lying smoothly on the sheet and producing a high gloss. Operating speeds of today's coating machines necessitate a clay composition of 60 and sometimes 70 pct solids as against the 35 to 40 pct required in the past. Since clays in suspension may solidify in flow, only those of intrinsically low viscosity can be used as high coating solids. THE literature of paper technology contains a number of articles having reference to developments in the field of coating and filler clays for use in paper manufacture. Much of this information has not been included in mining publications and has therefore not been readily available to all in the mineral industry. Recent developments in this field, including spray drying of clays, are presented here. U. S. Bureau of Mines figures for 1952 indicate that the paper industry consumes more than 50 pct of all kaolin produced and sold in the U. S. As most of the kaolin used by the industry comes from Georgia producers, the fraction of their output destined for paper use is thus appreciably higher than 50 pct. Small wonder that the kaolin industry, especially in Georgia, is highly sensitive to the quality requirements of paper mills and must respond promptly to technological developments in paper manufacturing. The paper industry itself is not the ultimate consumer. For the greater portion of the clay the end product is the printed page, and the demands of printing and publishing have sparked some of the technological advances in paper making which have, in turn, brought about methods employed in the kaolin industry. As compared with the product of 20 or 25 years ago, one of the most striking characteristics of the graphic arts today is the mass production of quality printing of fine pictorial work, much of it in full color. During this time periodicals with printing standards close to those of yesterday's slick-paper publications that were printed on a slow schedule and for a limited circulation have grown to the point where they go out to many millions of readers, often at weekly intervals. The complexity of technological improvements brought about by this increased circulation is probably not appreciated even by technical people, unless they have had reasonably close contact with the industry. The advance has come about through developments not only in the art of printing, but also in the field of paper making and even at the level of clay mining and processing. The smoothness required for faithful reproduction of the kind of printed matter under consideration is attained with a clay-coated paper. Since the distribution expense of the publication will depend to a great extent on its weight, the paper used must not be too heavy. This means a lower basis weight than was normal for conventional clay-coated papers some 25 years ago. And for this mass production market it becomes necessary to provide a paper having these and all the other required characteristics at a very moderate price—not the premium price conventional clay-coated papers formerly demanded. This challenge has been met by a new method of producing coated paper. In the past, application of clay coating to paper was a conversion operation, performed separately from the making of the base sheet. The newer development is called machine coating. Here application of the coating is an integral step in a continuous process by which wood pulp, clay, and other ingredients are manufactured into a sheet of coated paper. Many more problems are involved in this procedural change than are apparent at a casual glance. The coating operation, for example, must function at much higher linear speed than could be obtained with coating mechanisms previously employed. The application machinery developed to meet this requirement necessitated changes in composition of the coating color.* This created new requirements, summarized below, for the clay employed as coating pigment. In addition to smoothness, a relatively glossy printing surface is needed, and to a large measure it is the function of the coating clay to make possible the development of both these surface characteristics. Traditionally, pigments such as satin-white, prepared by reacting lime with paper-makers' alum, were used to assist in producing a high finish. However, economic considerations and others preclude large-scale use of such material in the new processes. In the 1930's Maloney' discovered that a certain particle size fraction of kaolin, consisting

Jan 1, 1956

By Robert E. Green, Robert A. Swanson

Ultrasonic attenuation and stress were measured simultaneously as a function of strain for aluminum single crystals tested in compression. The propagation mode and polarization of the ultrasonic waves were chosen with reference to the theoretical analysis presented in Part I. Good experimental agreement was found with this theory and with earlier experimental work in tensile tests. Support is given to the contention that ultrasonic -attenuation measurements are much more sensitive to the early stages of plastic deformation than are conventional stress -strain measurements. Dislocation meclzanisms are suggested which are compatible with both the present and the earlier experimental observations. A brief historical introduction of previous work concerned with the study of dislocation motion by ultrasonic-attenuation measurements has been given in Part I. The purpose of the present experimental investigation was to make use of the theoretical considerations from Part I in order to gain further knowledge concerning dislocation motions during plastic deformation. Emphasis was placed on the choice of propagation modes and polarization of the waves, such that interactions between these waves and dislocation movement on a specific slip system could be investigated. EXPERIMENTAL PROCEDURE Since the primary concern of this investigation was dislocation damping, other sources of damping were eliminated as much as possible. The test specimens were 0.5-in.-diam single crystals of 99.99+ pct pure aluminum grown from the melt by a modified Bridgman technique. Ultrasonic-attenuation measurements were made at a frequency of 10 megacycles per sec using a Style 56A001 Ultrasonic Attenuation Comparator manufactured by Sperry Products Inc. after a design by Chick, An- derson, and Truell.1 At this frequency the particle vibrations are essentially adiabatic and thermo-elastic damping should be absent. This frequency was selected since it was one of the frequencies used by Hikata et al.2 n conjunction with tensile tests on aluminum crystals, thus allowing direct comparison with this work. The use of quartz-crystal transducers insures that the amplitude of vibration is not sufficient to cause the break away of the dislocation loops from weak pinning points. The quartz-crystal transducers used all possessed a resonance frequency of 10 megacycles per sec and were thin circular discs 0.375 in. in diameter. X-cut crystals were used to generate the longitudinal waves and AC-cut crystals to generate the transverse waves. Aluminum was chosen as the basic material because it is a typical fcc metal whose deformation behavior is well-known and because the most recent work at the time the present research was initiated was that by Hikata et al. who used aluminum. The present tests were run in compression to see if such tests could be satisfactorily run in compression without being severely masked by grip effects.. A second reason was to compare the results in compression with those of the tension experiments of Hikata et at. Finally, shorter specimens could be run in compression with less over-all damping than in tension. All of the aluminum-crystal test specimens used were oriented for plastic deformation by single slip; i.e., they possessed the orientation having a maximum Schmid factor of 0.5. Because of the well-known time dependence 3 of plastic strain at constant stress, the test specimens were subjected to a quasi-static loading. Previous investigations4-' have indicated that attenuation after plastic deformation is also time-dependent, so any continuous loading of the specimen would show that changes in attenuation were also a function of strain rate. By loading the specimen to a given stress level and holding it constant until the recovery process was essentially complete, the time dependence was eliminated. The quartz transducer was permanently bonded to the aluminum crystal using Eastman 910 cement. Excess cement was removed from around the quartz with DMF (dimethyl formamide). Eastman 910 was found to be far superior for bonding, especially with regard to the shear-wave transducer, since it formed a solid bond which readily supports shear-wave propagation. The solid bond formed by the Eastman 910 cement also insured that the quartz

Jan 1, 1964