Search Documents

By John S. Johnson, Thomas Fraser

SIZING is the process of separating mixed particles into groups of particles all of the same size, or into groups in which all particles L range between certain definite maximum and minimum sizes. In coal preparation, sizing is generally accomplished by passing the coal over screens. Separation by differential settling in air or water currents has been adapted to the special field of separating very fine sizes, and these processes are in commercial use to a relatively small extent in the coal industry. Separation with screens is a very old industrial practice. Agricola 1 described the use of screens for ore treatment in the middle ages. In the literature of the British coal industry references were made to the screening of coal as early as 1589, but the practice of extensive sizing for the market did not become general until the last half of the nineteenth century. In America, the practice of sizing developed first in the Pennsylvania anthracite region, beginning with the use of rakes2 in the mine working places to recover coarse coal. This mining procedure left the fines in the mine. Preparation outside the mine started with the installation of stationary cast-iron plates with 4 to 6-in. square holes. The run-of-mine coal was dumped upon the platforms, the large pieces of rock were picked out by hand, and the large lumps of coal were broken with hammers. The term "breaker," which still applies to the anthracite-preparation plant, originated with this practice, but the term is no longer descriptive of the entire function of the plant. In 1884, the first power-operated anthracite coal breaker3 was erected by Gideon Bart at his colliery at Wolf Creek near Minersville, Pa. This plant utilized a system of rolls for breaking the coal and revolving screens for sizing. The plant was driven by a steam engine. It could handle

Jan 1, 1943

By Charles Y. Clayton

Cast-steel runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Folcyl found not only the usual ingot structure, but zones of Widmannstättian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent. nickel and 0.350 per cent. carbe a and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. Th macrostruc-ture, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregat'ion of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of the runner and in all parts of the individual grains. The upper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 1, 1922

By Charles Y. Clayton

Cast-steel runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Folcyl found not only the usual ingot structure, but zones of Widmannstättian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent. nickel and 0.350 per cent. carbe a and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. Th macrostruc-ture, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregat'ion of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of the runner and in all parts of the individual grains. The upper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 1, 1922

By T. C. Campbell

Copper is extracted from the Chuquicamata oxide ore by a hydro-metallurgical process. The ore is crushed to 3/8-in. sizing, and leached with a sulfuric acid electrolyte. Chlorine is precipitated. and the ferric iron reduced in the enriched electrolyte, after which the copper is recovered by electrolysis with insoluble Chilex and lead-antimony anodes, the spent electrolyte being returned to leaching. Cathodes are melted and refined in market furnaces and cast into commercial wire-bar and cake shapes. Sulfuric acid for the process is supplied by the brochantite in the ore. Water for washing the ore is advanced through the solution system and finally after cutting by electrolysis to from 6 to 16.0 grams per liter is completely stripped by the cuprous chloride method and run to waste. The cuprous chloride so obtained plus that resulting from precipitation of chlorine from strong solution is dissolved in ferrous chloride brine and the copper cemented on scrap iron. The cement so obtained is in part used to reduce ferric iron in electrolyte, and as it is of exceptional purity is also furnace refined and cast into an exceptional quality of fire-refined copper. Fig. 1 is flow sheet of the operation. The reduction plant is composed of seven divisions as follows: (1) crushing, (2) leaching, (3) tailings disposal, (4) dechloridizing, (5) sulfur dioxide treatment, (6) electrolytic tank house, (7) smelting and melting. A brief description of each of these divisions will be given. Crushing Ore that is frequently blocky and up to 5 ft. in section is crushed in four stages to 3/8-in. mesh. The first stage of crushing is called primary and the next three stages are known as secondary crushing. The first stage is accomplished with two 60-in. Superior McCully gyratory breakers by which the ore is broken to 9 in. The second coarse gyratory breakers crush the ore to 3-in. sizing. There are seven No. 10 McCully gyratories in this service, for one of which recently has been substituted a No. 7 cone crusher. The third and fourth stages of crushing are accomplished by fifty 48-in. disk crushers. In the third stage 14 disk crushers break the ore to 1 in., and in the last stage 36 disk crushers turn out the final product of 0.371-in. sizing. Reference to the flow sheets of Figs. 2 and 3

Jan 1, 1934

By James O. Lewis

Gravity drainage is the self-propulsion of oil downward in the reservoir rock. Under favorable natural and operational conditions, it has been found to effect recoveries comparable to water displacement. With modern technical knowledge, the operator can often make a choice between dissolved gas drive, water drive and gravity drainage as the principal recovery agent in a reservoir. It is desirable that the opeator be able to determine which of the three agents will be most effective under each set of conditions. So far, gravity drainage has received less consideration than the other two. In this paper. an endeavor is made to set forth some of the principles of gravity drainage, to point out the types of reservoirs favorable for it, and to show how it may be applied in them. Field examples are described and discussed. Introduction Since early in the history of the oil industry, it has been recognized that gravity is one of the three important natural forces for expelling oil from the reservoir rock. As knowledge of the technology of oil recovery progressed, ideas changed with respect to the relative importance of the three forces and with respect to the manners in which they functioned. For a time, disproportionate emphasis was placed on the importance and function of gas and the need for conserving gas pressures. More recently, disproportionate emphasis has been placed on encroaching edge water. Only lately has there been evidence that the function and importance of gravity was to receive due consideration. Study of this neglected phase of oil recovery is needed to round out our knowledge of reservoir behaviors and to gain a balanced viewpoint of the interplay of forces that may operate in varying importance in reservoirs. The purpose of this paper is to discuss mainly in a qualitative way, the functions of gravity, to present some concrete instances where it has been important and to raise some questions that should be investigated further. Oil-recovery Agents The important natural agents for effecting oil recovery that may be originally available in a reservoir are gas, both dissolved in the oil and free in gas caps, encroaching edge water and gravity. Each of these agents can act in a dual capacity—physically to overcome the surface energies that hold the oil within the pores and mechanically to overcome viscous . resistance and to propel the oil through the porous reservoir rock to the wells. Advancing edge water displaces the oil from the pores and lifts it updip to structurally lower wells. Gravity drains the oil from the pores and flows it downdip to the wells. Gas displaces oil from the pores, entrains it in the gas stream and flows it to the wells, but gas in solution also affects the physical properties of the oil and thus can influence oil recovery by the other agents, whether or not the mechanical energy in the gas is utilized. Of the two functions of these agents, the more important is the ability to dis-

Jan 1, 1944

By James O. Lewis

Gravity drainage is the self-propulsion of oil downward in the reservoir rock. Under favorable natural and operational conditions, it has been found to effect recoveries comparable to water displacement. With modern technical knowledge, the operator can often make a choice between dissolved gas drive, water drive and gravity drainage as the principal recovery agent in a reservoir. It is desirable that the opeator be able to determine which of the three agents will be most effective under each set of conditions. So far, gravity drainage has received less consideration than the other two. In this paper. an endeavor is made to set forth some of the principles of gravity drainage, to point out the types of reservoirs favorable for it, and to show how it may be applied in them. Field examples are described and discussed. Introduction Since early in the history of the oil industry, it has been recognized that gravity is one of the three important natural forces for expelling oil from the reservoir rock. As knowledge of the technology of oil recovery progressed, ideas changed with respect to the relative importance of the three forces and with respect to the manners in which they functioned. For a time, disproportionate emphasis was placed on the importance and function of gas and the need for conserving gas pressures. More recently, disproportionate emphasis has been placed on encroaching edge water. Only lately has there been evidence that the function and importance of gravity was to receive due consideration. Study of this neglected phase of oil recovery is needed to round out our knowledge of reservoir behaviors and to gain a balanced viewpoint of the interplay of forces that may operate in varying importance in reservoirs. The purpose of this paper is to discuss mainly in a qualitative way, the functions of gravity, to present some concrete instances where it has been important and to raise some questions that should be investigated further. Oil-recovery Agents The important natural agents for effecting oil recovery that may be originally available in a reservoir are gas, both dissolved in the oil and free in gas caps, encroaching edge water and gravity. Each of these agents can act in a dual capacity—physically to overcome the surface energies that hold the oil within the pores and mechanically to overcome viscous . resistance and to propel the oil through the porous reservoir rock to the wells. Advancing edge water displaces the oil from the pores and lifts it updip to structurally lower wells. Gravity drains the oil from the pores and flows it downdip to the wells. Gas displaces oil from the pores, entrains it in the gas stream and flows it to the wells, but gas in solution also affects the physical properties of the oil and thus can influence oil recovery by the other agents, whether or not the mechanical energy in the gas is utilized. Of the two functions of these agents, the more important is the ability to dis-

Jan 1, 1944

By J. W. Freeman, J. P. Rowe, R. F. Decker

HEAT-to-heat variations in properties of an alloy of constant nominal chemical composition have been a perplexing problem to the metallurgist. These heat-to-heat differences have been especially baffling in high-temperature metallurgy. In order to establish fundamental reasons for these heat-to-heat variations, the National Advisory Committee for Aeronautics has sponsored and financially assisted an extended research program on heat-resistant alloys at the University of Michigan. As part of the program to find the contribution of processing variables, Frey, Freeman, and white' studied effects of heat treating on nickel-base alloys and Ewing and reeman' investigated effects of hot-working practice on N155 alloy. To extend the program to the study of effects of melting practice on high-temperature properties, a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 pct A1 composition was selected for experimentation. The objective of this program was to establish the melting-practice variables which influenced the hot-working characteristics and creep-rupture properties and, at the same time, establish the metallurgical mechanisms for the effects. During the course of the investigation of practices using vacuum melting, it became increasingly evident through chemical analyses supplied by industrial concerns that a major variable was melt reaction with the crucible. This paper is devoted to the results of this phase of the melting-practice study. EXPERIMENTAL PROCEDURES Experimental 10-lb heats were induction melted in the University of Michigan vacuum-melting unit with the melting practices outlined in Table I. Aim analysis for the basic alloy, in wt pct, for all heats was as follows: Cr Co Mo Ti Al 20.0 15.0 4.0 3.1 3.1 Mn Si C Ni 0.12 0.12 0.08-0.15 Bal. Small amounts of boron and zirconium were added to certain heats as listed in Table I. These additions

Jan 1, 1959

By J. Brett, S. Friedman

A study of the diffusion of nickel into both fibrous and recrystallized 0.065-in.-diam silica-alumina doped tungsten wire at 1200°C has been conducted. The diffusion profiles were determined by chemical dissolulion of successive circumferential layers and spectro-photometric determination of nickel in the etchant. It was shown that the diffusion of nickel into tungsten is markedly structure-sensitive. No significant amount of nickel could be introduced at 1200°C into tungsten which had first been recrystallized at temperatures of 2300°C, leading to an upper limit estimate for the bulk diffusivity of nickel in tungsten of 10-11 sq cm per sec at 1200°C. However, nickel did diffuse into initially fibrous wires, caused re crystallization, and was alsays present at the advancing recrystallization front. The accumulation of nickel in an initially fibrous region ceases when the recrystallization front arrives. The characteristics of the resulting diffusion profiles are explained in terms of the relation between diffusion processes and micro structural changes. WHILE it is well-known that the presence of nickel and certain other metals causes low-temperature recrystallization of the cold-worked fibrous structure of doped tungsten,''' the character of the phenomenon is not well understood. Recently it was shown that the recrystallization reaction can be induced at low temperatures by the presence of solid nickel on the surface of doped wire, but not by exposure to nickel vapors.3 Once recrystallization was initiated, a continued source of nickel was required for propagation of the recrystallization front. The phenomenon appeared to be a complicated solid-state reaction since, in addition to the change in structure of the tungsten from fibrous to equiaxed grains, diffusion of nickel from the surface into the recrystallized and fibrous structures was occurring with possible chemical reaction between nickel and tungsten at the surface and interaction of nickel with the dopants which ordinarily stabilize the fibrous structure within the wire. The objective of the present work was to study the diffusion of nickel into fibrous and recrystallized tungsten structures in order to clarify the relationship of the diffusion process to nickel-induced recrystallization. Studies of interdiffusion in the Ni-W system4"7 have been principally concerned with the mobility of tungsten in nickel. Information on diffusion of nickel in tungsten is meager, and there seem to be no studies of the mobility of nickel in tungsten which elucidate the structural aspects of the phenomenon. The present experiments were designed to determine the diffusivity of nickel at 1200°C in fibrous tungsten, in large-grained tungsten prerecrystallized at high tem- perature, and in tungsten recrystallized at 1200°C due to the presence of nickel. Although the concentration profiles were determined in these experiments, unexpected changes in boundary conditions or complex diffusion paths complicated the analysis of these profiles so that the interpretation could not be readily expressed in terms of simple diffusivities. EXPERIMENTAL PROCEDURE The experiments were conducted on Sylvania 0.065-in.-diam silica-alumina doped commercial tungsten wire, hereafter designated as ordinary doped wire. A special lot of 0.065-in.-diam silica-alumina doped low-nickel wire was also used. Impurity analyses of the wire are given in Table I. The experimental design is shown in Fig. 1. All heat treatments were conducted in vacuum. Two groups of ordinary doped wire were prepared for diffusion with nickel. One group in the as-received (fibrous) condition was elec-tropolished, nickel-plated, and annealed at 1200°C for 20 and 40 hr, or was exposed to nickel vapor at 1200°C for 20 and 40 hr. The second group was recrystallized to an equiaxed grain structure at 2300°C for 3 hr, electropolished, nickel-plated, or exposed to nickel vapor for anneals at 1200°C for 20 and 40 hr.

Jan 1, 1969

By Lawrence A. Roe

The magnetic reflux classifier, which utilizes the combined effects of magnetic fields and a hindered settling classifier, is a new tool for determining the quantity and quality of middlings in fine-sized magnetite concentrates. Results are given for processing a typical taconite ore, and a sketch of the apparatus is included. IN examining magnetite ores and beneficiated products it often becomes necessary to make critical studies of the amount of grinding necessary to produce the desired degree of magnetite liberation. In the past this has been accomplished by laboratory heavy-liquid tests, which provide a method for selectively removing middling particles and free magnetite from various-sized fractions. Examination of the various products under the microscope results in fairly accurate determination of the degree of liberation. The method is quite efficient on sizes coarser than 325 mesh. Thus the heavy-liquid method of middling separation was satisfactory until the advent of present day magnetic taconite studies. When magnetite concentrates ranging from 70 to 100 pct —325 mesh are studied it becomes apparent that older methods of determining liberation size are not satisfactory and that there is need for a new method. For example, some of the low-grade magnetite ores of the Wisconsin and Michigan iron ranges require grinding to 100 pct —325 mesh to produce a magnetic concentrate containing less than 12 pct silica. Examination of concentrates from such ores often reveals that many of the middling particles consist of only very minor proportions of iron mineral. Thus it becomes important to be able to determine the degree of grinding necessary not only for complete liberation, but also for liberation of only 80, 85, or 90 pct of the total iron mineral content. Actually, complete liberation is never attained, but is often used to designate that degree of liberation necessary for production of high-grade concentrates. A rougher concentrate, produced after elimination of a coarse-sized tailing, can usually be subjected to a second grinding stage and concentrated into a higher grade product than could be produced from the same crude ore with one stage of grinding resulting in the same overall size reduction. This fact adds to the importance of being able to determine partial degrees of liberation on any magnetite ore. Standard laboratory methods such as heavy-liquid separation, microscopic grain counts, Davis tube magnetic separation, magnetic flocculation, classification, flotation, and others often are not applicable, or are prohibitive because of time requirements when large numbers of fine-sized magnetite samples are investigated. The Davis tube magnetic separator is an efficient tool to use in rejecting the non-magnetic mineral particles from an ore sample. The middlings discarded by the tube separator usually are so low in iron content that they can be considered relatively unimportant in liberation studies. This condition is caused by the extremely high flux density used in the Davis tube. This flux density ranges from four to eight times the flux density produced by most of the powerful commercial machines in use today. Thus the problem resolves itself into a search for a method of selectively removing middlings from Davis tube magnetic concentrates which will be both rapid and efficient. Those methods showing most promise in the development of a process for isolating middlings from extremely fine-sized magnetic concentrates were flotation and magnetic flocculation. The use of flotation to remove middlings from magnetic concentrates is reported in the literature.'.' The flotation process is effective in removing middlings from a magnetite concentrate, but physical entrapment of fine-sized free magnetite in the silica-bearing froth is an undesirable feature. The flotation method of removing middlings requires time, effort, and precise control of many variables, and does not meet the required degree of middling isolation. Magnetic Flocculation Magnetic flocculation has long been resorted to"-" in efforts to upgrade magnetite concentrates. One of the new magnetic taconite plants now under construction on the Mesabi Range includes magnetic flocculation in the flowsheet' as an accessory process to remove high-silica middlings and free silica which has been mechanically entrapped in magnetite flocs. The use of magnetic flocculation as a laboratory method of making precise separation of middlings was further investigated, since it offered a rapid, simple method of accomplishing the desired result. Magnetic flocculation involves the subjection of a magnetic concentrate to a strong magnetic field, passing the concentrate in a highly flocculated condition to a hydroseparator or other classifiers of various types, and removing free silica and middlings as overflow products. In an attempt to utilize simple

Jan 1, 1954

By John Chipman

The concentration of a solute in a dilute ),zetallic solution may be measured by any of several parame- ters including weight percent, atom fraction, atom ratio, and lattice ratio. The ratio of filled to unfilled interstitial sites is useful for interstitial solutes. A variable 2 proportional to this ratio is used as a measuve of concentration. For component 2 irz a bitzary solution z2 = n2/Ym - nz/b) where b is the numberber of interstitial sites per lattice atom. For a t~lul-ticortzporzent solution this becomes zz = n2/(nl + Cvjnj) in which Vj = - l/b for an interstial solute and +1 for a substitulional solute. In the infinitely dilute solution the activity of an interstitial solute 2 is proportional lo z2. At finile concentration the departure from this limiting law is expressed us an activity coefficient, his coefficient is a function of concentra1io)z expressed as tevactiolz coeffcient 8; is analogous to the jark~iliar e£ bul is found to be independent of concentvation in certain solutions for which data are available. It is found that the same equations may be used to express the activity of a nonmetallic solute, sulfur, in liquid solutions of iron containing other solutes, both metallic and nonmetallic. For a nonmetallic solute or for one which strongly increases the actiuity of sulfur, it is convenient to assign arbitvarily a value vj = — 1. When this is done the derivative is found to be constant in each of the ternary solutions studied. The activity coefficient of sulfur in a complex liquid iron solution may be expressed as where nk is a second-order cross product determined in the quaternary solution Fe-S-j-k. The equation is used to calculate tlze activity of sulfur i)z three sevetl- component solutions. IN thermodynamic calculations concerning dilute solutions it is unnecessary to invoke laws and relations which extend across the concentration range to include concentrated solutions. In most binary metallic systems, as arkeen&apos; has recently pointed out, there exist two terminal composition regions of relatively simple behavior, connected by a central region of much greater complexity. When the solute is a nonmetal there is only one such region and in many systems the concentration range is extremely limited. It is the purpose of this paper to suggest a method for the calculation of activities in such a terminal region in which one or more solutes are dissolved in a single solvent of predominantly high concentration. HENRY&apos;S LAW In the usual textbook statement of Henry&apos;s law, concentration is stated in mole fraction. This has the advantage that it makes Henry&apos;s law thermodynamically consistent with Raoult&apos;s law. Since all measures of concentration at infinite dilution are related by simple proportion it follows that mole fraction, molality, atom ratio, weight percent, or any other unit of concentration can be used with the appropriate constant. At finite concentrations, however, calculations based on the law depend upon the unit employed. Deviations from Henry&apos;s law at finite concentrations depend upon the composition variable employed. They are evaluated in terms of activity and interaction coefficients2 which have become familiar features of metallurgical thermodynamics. It is the purpose of this paper to propose a measure of concentration for metallic solutions containing interstitial or nonmetallic solutes by means of which the calculation of activities in complex solutions may be simplified. The discussion will be restricted to free-energy interaction coefficients3 typified by Wagner&apos;s c|a BINARY SOLUTIONS The several measures of concentration which are to be considered are shown in line a of Table I. The corresponding activity coefficients are in line b and the deviation coefficients, sometimes called self-interaction coefficients, are in line c. Henry&apos;s law simply states that the activity coefficient approaches a constant value at infinite dilution. By adoptihg the infinitely dilute solution as the reference state and defining the "Henrian" activity as equal to the concentration in this state, the activity coefficient is always unity at infinite dilution. This convention is far sim~ler and more useful in dilute solution than emploiment of the &apos;Raoultian" activities and it will be used in the following discussion. The several definitions and equations of Table I will be referred to by means of their coordinates in the table. Early observations of deviations from Henry&apos;s law in metallic solutions were shown graphically4 rather than analytically. For the case of sulfur in liquid iron5 the slope of a plot of logfs vs (%S) was constant in the range 0 to 4.8 pct S, indicating constancy of eh2&apos; in Ic. He was proposed by wagnerz and has been widely adopted. The a function of IIIc recently employed by ~arkenl was designed specifically for dilute solutions. Darken has shown that the value of a12 remains essentially constant for many binary solutions within a substantial range of compositions. The atom ratio is directly proportional to the molalitv.<, a conventional measure of concentration. IVb and C served as the basis for smith&apos;s6 classic studies of

Jan 1, 1968

By A. F. Baker, E. R. Palowitch, A. W. Deurbrouck

As air-pollution regulations become increasingly more stringent, increased significance is being placed on the amount of sulfur present in coals used for steam generation. These regulations are aimed at minimizing the pollution of the atmosphere with noxious gases such as the sulfur oxides that are formed and emitted when coal is burned. Two meet these future requirements, a definite need exists to reduce the sulfur content of some of the coals used for steam generation. Reducing pyritic sulfur involves liberating the pyrite from the coal and then removing it. The specific gravity of pyrite is high (5.0) compared to that of coal (about 1.2, mineral-free), and standard coal-washing devices, such as wet concentrating tables, will efficiently remove pyrite particles larger than about 100 mesh. Particles below this size will be entrained in the table water and will be carried into the clean coal product. Techniques such as froth flotation are of little benefit for pyrite reduction because the flotation characteristics of pyrite are similar to those of coal.

Jan 6, 1966

By W. E. Anderson, T. M. Brady

As part of a larger study to identify factors influencing the practical operating life of wire rope used on large draglines in surface coal mining, field trips to operating surface coal mines were made during late 1975. Wire rope performance information was obtained from personnel at 13 mine sites west of the Appalachians. Seventeen pieces of equipment, utilizing bucket sizes ranging from 30 to 220 cu yd (23 to 168 m), were documented. Draglines at large US surface coal mines can be represented as 120 machines having 60-cu yd (46-m3) buckets, moving 1.8 X 109 cu yd (1.4 x 109 m3) of overburden during 6650 hours of productive availability per year. Based on the limited field study, the calculated downtime resulting from rope-related causes averages 105.6 hours per year for each typical 60-cu yd (43-m3) dragline. The total loss in production from this source alone is thereby estimated at about 25 x 106 cu yd (19 x 106 m3) annually. Although study findings did not reveal anything about dragline rope life that wasn&apos;t known or practiced by one operator or another, most operators can expect improved rope life by periodic review of their practices and by adopting one or more life-improvement measures employed at other sites. Since rope productivity was found to vary by a factor of five among the sites studied, considerable improved average performance is possible. As little as 10% overall improvement would increase national productivity by 2 million cu yd (1.5 X 106 m3) of solid overburden removal. Associated savings in rope costs would be some $2 million annually, plus a large reduction of labor-related expenses. This report outlines preliminary findings which may prove useful to many operators in extending wire rope life. Some of these modifications or adjustments in maintenance/operating practices would not require capital investment. During the field survey, no company was found which had tried cost reductions by using presocketed dump ropes, or dump rope sheaves that opened like a snatch block, so these are suggested as possible improvements requiring modest capital input. Data Acquisition During the field visits, mine operators provided rope life information about their machines. Some of the rope life data consisted of gross averages; other data was in the form of detailed records, including rope construction and manufacturer, cutoff and resocketing periods, end-for-end switching, and downtime for rope change-out. Trends of average hoist rope life and average drag rope life determined from the field study are shown in [Fig. 1] as a function of bucket size. The three lines on the graph have slopes of 1, M, and 1/4. A comparison of the data shows that hoist ropes moved about twice as much material as drag ropes prior to retirement, although more than a two-to-one scatter within each category is evident. As expected, the larger machines with the larger buckets moved more total volume of material. The four pairs of solid symbols represent those data for which detailed rope life histories are presented in subsequent figures.

Jan 1, 1980

By J. Chipman, H. Towers, M. Paris

A simple radioactive tracer technique is used to measure the diffusion coefficient of calcium ion in molten slags. In a slag of 40 pct Ca0-40 pct Si0,-20 pct Al203, Dc " at 1450°C is 1.3x10-6 cm&apos; sec-&apos;. THE application of the principles of thermodynamics to steel and iron making problems has proved so fruitful that the kinetic approach has tended to be neglected. It seems probable that in some reactions the rate-determining step is the dif-fusivity of the reactants or of the products. But knowledge of the diffusion coefficients of the constituents of liquid slag and metal is singularly lacking. The present work was undertaken as a first step toward supplying such data for slags. Furthermore, any additional information on the physical properties of liquid slags might be expected to help in elucidating their structure. It is essentially a preliminary investigation, the course of which was determined more by the necessity of establishing a method than by the immediate intrinsic interest of the results. For example, the selection of calcium ion to be studied was dictated by the suitability of the isotope Ca45 in that it is a simple emitter with a long half-life. Of the other ions commonly encountered in slags, the isotopes of iron and manganese have relatively complex radiations as well as the normal disadvantage of requiring control of the oxygen potential of the atmosphere; Mg27 and Al29 have half-lives measured only in minutes; Si3&apos; has a simple decay process but its half-life of 2.8 hr is too short for preliminary studies; the only useful oxygen isotope is the stable O18; and there remain only sulphur and phosphorus both of which have suitable isotopes but were rejected as being of less fundamental interest than calcium. Similarly a lime-alumina- silica slag was used in preference to calcium silicate primarily because of its low melting point and its capacity to form a glass on fairly rapid cooling. Literature Review Very few studies of diffusion in liquid silicate systems have been reported. In order to determine the origin of diopside inclusions in felspathic rocks, Bowen1 investigated the diffusion between diopside and various mixtures of albite and anorthite. Platinum crucibles were used with diopside, the heavier of the two liquids, forming the lower half of the cell and diffusion taking place against gravity. Change in concentration along the diffusion path was found by measuring the refractive index of the quenched glass. Nearly thirty years later McCallum and Barrett2 used essentially the same method to determine the diffusion coefficient of lime in lime-alumina-silica slags. In this case the interest was to find the rate-determining step in the process of slag attack on refractory materials. In an investigation of the kinetics of the sulphur reaction, Derge, Philbrook, and Goldman8 determined the diffusion coefficient of sulphur in a typical blast furnace slag by the simple procedure of melting a slag containing 2 pct S over an identical slag sulphur-free. They make no claim to a high degree of accuracy but suggest that D, is of the order of 10-6 cm2 sec-l. Other high temperature liquid diffusion studies have been concerned with metals. Holbrook, Furnas, and Joseph4 determined the diffusion coefficients of silicon, phosphorus, sulphur, manganese, and carbon in liquid iron by immersing a small carbon crucible containing pure iron-carbon alloy in a large vessel containing iron with a high concentration of the particular element. Their results were confirmed by Paschke and Hauttmann5 using a similar method. Diffusion coefficients in silicates in the glassy state have been studied by Johnson, Bristow, and Blau6 Both Na24 and Ca45 were used as tracers but only the

Jan 1, 1954

By J. McLaren Forbes

Geologists and engineers in charge of diamond drilling often have no practical experience in the work, yet they must direct the drillers. In discussing some of the problems that arise, the author of this paper has tried to remember the things he did not know about diamond drilling when he first came in contact with that work. The basic reason for most diamond-drill holes is to obtain information. The more thorough the understanding of the geological and engineering problems involved, the greater will be the benefit derived from a drilling program. One of the best methods to ensure some thinking before drilling is to record on the permanent drill log, before the hole is collared, the reasons for the work and the information desired from that particular hole. When the hole is finished, the information obtained should be recorded. Driller The choice of a diamond driller is very important. If no experienced driller is available, a competent miner who has a sense of responsibility and better than average mechanical ingenuity can do the work. The best answer to most practical drilling problems, from the standpoint of the person in charge of the drilling program, is the service of experienced diamond drillers or drilling firms. Equipment Drilling equipment should be adequate to put down the longest hole desired and handle the toughest ground encountered. The type of bit used depends upon the ground drilled. Experimenting with various bits and careful study of footage records are the best means of determining which to use. Under ordinary circumstances it is best to drill using an EX barrel when possible. The length of rod and core barrels that can be used depends on the size of the drill station. Also, the length of core barrel depends on the way the ground cores. In good ground as much core will be recovered with a 10-ft. barrel as with a shorter one, and with considerable saving of drilling time. A water pump is needed if the hole is so deep that the water pressure is not strong enough to wash out the cuttings, or if it is drilled at an angle that prevents full force of the water pressure. Instructions For an Inexperienced Driller 1. Never run a bit too long a time. When a bit seems to be "good for one more run," discard it. 2. Always let the rods down on bottom easily. Protect the bit from sudden shock. 3. Start the drilling slowly and easily. Do not put pressure on the bit too fast. Diamonds can break. 4. Be sure the water pressure is strong enough to clear the bit, but do not use more water than is needed, as it may wash away the core. Usually, if no core is recovered the hole is a total loss. 5. When dry-blocking, do not run without water longer than necessary as the bit may burn. 6. Be sure the rods are well caulked and tightly screwed together. If not well caulked they will lose water, and if not

Jan 1, 1946

By F. D. Rosi, C. A. Dube, B. H. Alexander

WHEN a deformed polpcrystalline metal is heated to a sufficiently high temperature, a recrystallized structure develops which consists of small, essentially stress-free grains. This transformation is referred to as primary recrystallization. Under certain conditions, on prolonged annealing of the specimens, a type of grain coarsening occurs in which a small number of grains commence to grow at various points by devouring the neighboring finegrained primary structure, which, in itself, exhibits a marked stability toward normal grain growth. This grain coarsening process has been referred to by Burgers&apos; as "secondary recrystallization" or "exaggerated grain growth." Although much work has been done on recrystallization and growth processes, present knowledge of the factors which determine the occurrence and growth of secondary grains is inadequate for the advancement of a theory which accounts for the observed characteristics of this recrystallization phenomenon. In this respect, it would be important to make measurements of the velocity of growth of these large secondary grains. The early work of Feitnecht2 on aluminum showed that the size of secondary grains increased with temperature and time, suggesting that such measurements would be possible. More recently, Burgers1 found that the growth velocity of these grains in aluminum was constant over a large time interval, as is generally found for the growth velocity of primary grains in a uniformly deformed test piece.3-5 It is reasonable to expect that the determination of the activation energy of the secondary growth process might lead to a better understanding of the underlying atomic mechanism. This investigation, therefore, is one of a series primarily designed to measure the growth velocity of secondary grains at various temperatures for silver, copper, and aluminum. It is hoped that these studies along with those of orientation relationships, will establish a sound basis for theorizing as to the origin and nature of the secondary transformation. Experimental Procedure The metal used in the present investigation was high-purity silver (999.9 fine), which was supplied in the form of cold-rolled plates 0.250 in. thick. These plates were annealed at 500°C for 1 hr and then straight-rolled to a thickness of 0.04 in. in three reductions of approximately 45 pct, followed in each case by an anneal at 450°C for 1/2 hr. The 0.04 in. sheets were given a final reduction of approximately 50 pct, which resulted in a thickness of 0.02 in., thereby insuring two-dimensional crystal growth. Individual specimens of this material about 1x3 cm were used for all heat treatments, unless otherwise noted. The annealing was carried out under an atmosphere of argon in an Inconel tube furnace whose temperature was controlled to within -+2°C. Metallographic examination of the secondary transformation was accomplished by mechanically polishing the specimens on one side to approximately one half their thickness through 2/0 metallographic emery paper, and then electrolytically polishing in a solution of potassium ferrocyanide and sodium cyanide. With a current density of approximately 20 amp per sq dm, the time required to obtain a satisfactory surface varied from 3 to 5 min. Standard potassium bichromate was used to etch the electrolytically polished surfaces. A heavy etch with this solution produced a sharp contrast between the secondary grains and the fine-grained primary structure, darkening the latter while leaving the large secondary grains bright. All area measurements of the secondary crystals were made with a planimeter on enlarged tracings of the grains.

Jan 1, 1953

By John A. Ames

Webster&apos;s dictionary nearly equates portland cement with its current primary definition of cement. While such equation may be a triumph of common usage, the confusion between the terms cement and concrete unfortunately is very widespread. Full definition of cement properly would extend to many substances, but for purposes of this chapter cement is restricted to "varieties" of portland cement including "portland-pozzolan" cement. Among the usually recited historical notes concerning cement is that it was developed by the Romans. Their use of cement in the great structures of Rome, and even in the far corners of their Empire, such as Hadrian&apos;s Wall in the north of England, testifies to the antiquity of a major cement industry. From English sources we know of John Smeaton&apos;s carefully proportioned hydraulic cement mixed in 1756 and of Joseph Aspdin&apos;s patented cement to which, in 1824, he gave the name portland cement. (He claimed that his cement mortar looked like the famous dimension limestone quarried from the Isle of Portland on England&apos;s south coast.) The year 1971 marked the centennial of portland cement manufacture in the United States. A fair historical account of the many real contributors to the cement industry between 1756 and 1972 unfortunately would be too extensive for this chapter. Development of rotary kiln practice and burning at higher temperatures clearly was the major move into today&apos;s technology. As part of the 4th edition of Industrial Minerals and Rocks, this chapter on utilization focuses on inferred interests of the anticipated readers. The main period for which statistics are cited generally is that since the 3rd edition (1960) of this same volume. Cement manufacture is the processing of selected and prepared mineral raw materials to produce the synthetic mineral mixture (clinker) that can be ground to a powder having the specified chemical composition and physical properties of cement. Cement making incorporates a number of distinct steps, but it is characterized by the key pyroprocessing (or "burning") step, which brings about the necessary changes in the raw materials. This pyro processing is a chemical process. Conversion of large volumes of mineral raw materials into specification-controlled cement at relatively low cost is the objective. Statistics on the cement industry are of uneven quality. The U.S. Bureau of Mines (USBM) is the principal collector of available data. These statistics can be only as good as the quality of information supplied by the reporting companies. The data perhaps most often questioned relate to productive capacity of the industry. The questions submitted by USBM are valid, nevertheless, and the information gained from them, as good as is available, is what is generally used. The Portland Cement Association also is a source of much quality information. The year 1972 witnessed a test of the adaptability of cement industry statistics. This was the year of conversion from barrels and sacks of cement as the units of measure to tons and hundredweights. The barrels and sacks related to volumetric measures in that a sack was judged to be 1 cu ft (weighing a "standard" 94 lb). A barrel was 4 sacks. Volumes of concrete are stated in cubic yards, and the number of cubic feet of cement in a cubic yard of concrete was a sensible approach to the mensuration involved. However, cements do not weigh the same amount from plant to plant or from type to type, and the buyer was more interested in getting an assured weight for his money than in "buying air." Thus, a sack, in accepted practice, became 94 lb instead of 1 cu ft, and a "barrel" became 376 lb, regard- less of whether it would fit into 4 cu ft of space. With the de facto dealing in weight rather than in volumes, the awkward numbers made little

Jan 1, 1975

By O. B. Bucklen, P. G. Meikle

INTRODUCTION The trend in the coal industry for many years has been to make every- thing "bigger and faster." This also held true for loading and storage facilities. Where once a million ton per year mine was rare, three to five million ton per year mines are not uncommon today in the bituminous industry. This greatly increased production, made possible through mechanization, required greatly improved loading facilities just to get the coal away from the mine. Also, there is a trend toward combining production from more than one mine and cleaning it in a single preparation plant. In addition to increased loading capacity, this frequently necessitates raw coal storage and blending facilities. The development of the unit train with its attendant economics, more than any other factor, has contributed to the widespread construction of storage and high-speed loading facilities. In the export market, the construction of ever larger coal colliers has contributed to a need for faster and larger loading facilities. In this climate of rapidly changing technology, any written account is faced with the possibility of obsolescence before its appearance. Thus, this chapter seeks to define the common and current practice in coal loading and storage facilities with the full knowledge that this practice is an ever-moving target. FUNDAMENTALS OF COAL STORAGE Storage of coal is becoming an increasingly important part of coal handling systems at mines, particularly since the advent of the unit train concept in transportation. In order to take advantage of reduced transportation rates on trainload shipments of coal offered by unit train movement, operators have found that storage is an economic necessity. In unit train practice large predetermined quantities must be loaded in relatively short periods of time as opposed to conventional practice where coal is loaded at a speed dependent on the production capacity of the mine and/or the cleaning capacity of the preparation plant. Two surveys of storage practices at mines reveal several objectives for storage.1, 2 Raw and/or clean coal storage is generally practiced in order to accomplish one, or a combination, of the following objectives: 1. To improve plant efficiency by distributing plant feed over the entire operating time, or to allow a preparation rate different from the production rate. 2. To limit interruptions of supply, ie, allow mine and plant to function independently with delays in one not affecting the operation of the other.

Jan 1, 1968

By H. J. French

WITHIN the past few years, particularly because of the rapid growth of the airplane industry during the war, considerable attention has been paid to the manufacture of light-wall cold-drawn seamless and welded steel tubing for structural purposes. While the manufacture of such tubing is not, in itself, a difficult matter, some difficulties have. been encountered in producing the same under specifications requiring definite physical properties. It is the purpose of this paper to describe the methods of manufacture and the properties that may be obtained by such methods for tubing coming within about ½ to 2 in. (12.7 to 50.8 mm.) outside diameter and 10 to 22 Birmingham wire gage (0.134 to 0.028 in. wall thickness). Such tubing is largely used as structural material in the aircraft industry, and it is of the utmost importance that the physical and chemical properties should be known, and also that the various factors entering into the manufacture should be under such control as to allow these properties to be varied and held within definite limits. In general, tubing may be divided into four classes: namely, specialty tubing, such as riveted-sheet or plate, lock jointed, etc.; brazed tubing; welded tubing; and seamless tubing. Welded tubing may be divided into hot product, such as lap welded and butt, welded, and cold product, such as acetylene and electric welded. Seamless tubing may be hot rolled or cold drawn.

Jan 9, 1919

By J. F. Butler

Boron nitride, BN, has been identified in boron low-carbon steels by means of light microscopy, electron microscopy and diffraction, and chemical analysis. This boron nitride is responsible for strain aging suppression in these steels through the removal of nitrogen from solution; however, small oxidizing potentials which result in deboronization In the austenitic temperature range also result in boron nitride decomposition and the subsequent occurrence of nitrogen strain aging. THE addition of boron to low-carbon steels is an effective means of eliminating the detrimental effects of strain aging;&apos;,&apos; however, the mechanism by which boron suppresses strain aging has not been established. In studying the effect of heat treatment on the strain aging of boron low-carbon steels, Butler3 found that no detectable nitrogen was present in the ferrite solid solution after various heat treatments even though the total nitrogen analyses of the steels were 0.003 pct N. Apparently the function of boron in suppressing strain aging is the removal of nitrogen from solution to form a relatively stable second phase. A clue to the identity of this phase was found by Speight4 who extracted from an aluminum-killed boron steel an acid insoluble residue which contained boron and nitrogen in proportions corresponding to the compound, BN. Shyne and Morgan5 found that the addition of nitrogen to a hardenable boron steel lowered its hardenability in a manner which suggest-d the presence of nucleating particles (presumably BN) even at high austenitizing temperatures. Although this indirect evidence for the presence of boron nitride in boron steels has been found, the compound was not identified metallographically as a separate phase in these steels. Because boron has an affinity for oxygen comparable to that of silicon,5 boron steels must be thoroughly killed with aluminum in order to prevent the reaction of boron with oxygen.7 The affinity of boron for oxygen also is demonstrated through the ease of deboronization of a boron steel in an oxidizing atmosphere. Digges, Irish, and Carwile8 found that a mixture of wet natural gas and air caused both deboronixation and decarburization of a boron steel at 1900°F. The boron content rose at the surface of the steel due to the formation of boron oxide. Shyne and Morgan9 encountered deboronization at much lower oxygen potentials; loss of boron occurred in steels treated at 1750o F under argon purified to 0.0014 pct 0, even though decarburization did not occur. Boron oxide, B2O3, is much more stable than the nitride, BN, as is indicated by the standard free energies of formation at 980oC: -235 kcal per mol of B2O3 (liquid) and -28 kcal per mol of BN (crystal). It is evident that the oxygen potential must be kept low in the presence of BN in order to prevent its decomposition and the subsequent formation of B2O3&apos; The purpose of the work described in this paper was to identify the nitride phase responsible for the removal of nitrogen from solution and to study its stability under oxidizing conditions. IDENTIFICATION OF BN In order to identify the phase containing boron and nitrogen, several alloys high in boron and nitrogen were made up in a small vacuum furnace. In alloys 3 and 4, Table I, electrolytic iron was used as a charge material. Boron additions were made in the form of 18 pct B ferro-boron after the iron was molten. In the case of alloy 3, the charge was solidified at this point; for alloy 4, nitrogen at 1 atm pressure was admitted over the melt before it was

Jan 1, 1962

By R. Floyd Farris

A method is presented for determining minimum waiting-on-cement time, which takes into account the differences that exist between types and brands of cements and such individual well conditions as depth, temperature, and pressure. The basis for the method was determined by laboratory tests. Being a laboratory development, several steps were required to prove its merit. The first step consisted of laboratory tests designed to determine the minimum cement strength required in wells. Basis was found for setting a minimum value of 8 Ib. per sq. in. tensile strength. Next, it was shown by laboratory tests that the time to 8 Ib. per sq. in. tensile strength may be expressed as a function of consistometer stirring time to loo "poises," the approximate relation being "the time to 8 Ib. per sq. in. tensile strength equals the time to I00 &apos;poises&apos; times three." Next, it was shown that the time of maximum temperature development in cement slurries, due to heat of hydration, is also related to consistometer stirring time to loo poises, but only by a factor of approximately two. It was shown also that the shut-in casing pressure will build up after cement is placed and register a maximum pressure at approximately the same time the slurry down the hole attains maximum temperature. From this and the relationships listed above, the general rule was established that minimum waiting-on-cement time (time to 8 Ib. per sq. in.) after casing cement jobs in any well is equal to the time when the shut-in casing pressure reaches a maximum, as measured from the initial mixing of cement, times a factor of 1.5. Cement plugs drilled in the field at the time prescribed by this formula were found to drill "firm to hard," thus confirming the laboratory tests. These tests prove that many of the present regulations for waiting on cement require a longer time than is absolutely necessary. Use of the method herein proposed offers the possibility of a saving of $1200 per well. Introduction The length of time allowed for cement to set after casing is determined either by state-wide rules, field rules, or self-imposed rules written into drilling contracts. In general, the time is dictated by experience and common practice. However, owing to differences in opinion and in experience of the various groups involved, waiting-on-cement time often varies from one area to the next. For example, an operator in an area where no rules exist may drill out of surface pipe at 24 to 36 hr., while another operator in another area may wait 48 hr. or more to comply with state or field rules, although the depth of the well, hole size, type of cement, and other data are identical. An even greater difference in practices will be found by making similar comparisons with respect to oil-string cement jobs. Differences in waiting-on-cement times of 36 to 48 hr. are common. Further complicating the picture is the rather common practice of allowing more waiting time for cement to set at the greater depths than is allowed at the shallow depths. This practice has existed for years in spite of the common knowl-edge1,2,3 that the temperature of the earth at the usual setting depths of surface

Jan 1, 1946