Search Documents

By W. H. Hough, P. B. Leavenworth

Development in the upper Texas Gulf Coast during 1944 resulted in the discovery of 19 new fields as compared with 11 during 1943. These discoveries include 10 oil fields, one dry gas field, and eight gas-condensate fields. Drilling During the year 590 wells were drilled as compared with 418 drilled during 1943. Of these operations, 485 wells were drilled in proven fields, with the following results: 281 oil wells, 22 condensate wells, one dry gas well and 141 dry holes. The remaining 105 wells were wildcats, of which 19 were producers. The geological distribution of these discoveries was as follows: In 1944, production amounted to 178,-522,630 bbl., which was an increase of some 31,670,384 bbl. over the 1943 figure of 136,852,246 bbl. These figures include both condensate and oil production, as separate figures are not available. Wildcatting in the area was more successful during 1944 than in 1943 as the following comparison of number of wells drilled illustrates: Discoveries during 1944 Smith Point, Chambers County.—Standard Oil Company of Texas completed its No. I State, sec. 109, on Feb. 15, 1944, in a Frio sand at 8135 to 8146 ft. The well flowed 250 bbl. of 42º gravity oil through an 1/8-in, choke. Gas-oil ratio was 800 to I; tubing pressure, 1100 bbl. Four other oil wells and one gas well were completed during the year. This discovery does not appear to be of major importance. The producing area lies on the upthrown side of a large fault. North Winnie, Chambers County.—Sun Oil Co. completed No. I P. E. Dougherty on Apr. 27, 1944, from the Frio, through perforations at 8757 to 8759 ft. The initial production was 154 bbl. of 38.3º gravity oil through an 1/8-in. choke. Gas-oil ratio Was 2526 to 1; tubillg Pressure, 2280 1b.; casing Pressure, 1225 lb.; total depth, 9519 ft. Three other wells were drilled during the Year. This discovery is on the downthrown side of the major Winnie Stowell fault, and increases in magnitude the already large producing area along this fault. Mayes Field, Chambers County.—Humble Oil and Refining Company's No. I Mary Etta Mayes was completed on Dec. 24, 1944, in a Frio sand, at 8166 to 8169 ft. through 1/4-in. for 768 bbl. of 40.3º gravity

Jan 1, 1945

By Ben B. Cox

During the past year considerable progress was made in the exploitation of Iraq's resources, although no new fields were discovered. The principal development was the completion of the much heralded pipe line from Kirkuk to the Mediterranean, by the Iraq Petroleum Co., Ltd., and the beginning of crude exports to Europe on the second of August. Official ceremonies for the opening of the lines took place in January, 1935. The line in itself is sufficient achievement under the existing natural handicaps to deserve a moment's attention. It is 1151 miles long, composed of two independent lines made up mostly of 12-in. with some 10-in. and 8-in. pipe, and extends from Kirkuk westward 156 miles to beyond the Euphrates River as a double line. From that point, near the village of Haditha inside the Iraq border, it bifurcates, one leg going as a single line to Haifa through the British Mandated Territories of Trans-Jordania and Palestine, and the other to Tripoli through the French Mandates of Syria and the Leban(on)ese Republics. The total length of the Tripoli line is 532 miles, of the Haifa line 619 miles. The line leaves Kirkuk at an elevation of 1013 ft., drops to 350 ft. at the Tigris, to 200 ft. at Wadi Tharthar west of the Tigris and again to 300 ft. at the Euphrates, rises to more than 3150 ft. at mile 451 on the central Arabian steppe along the south line and to more than 2500 ft. at mile 466 along the north line. On crossing the rift valley of the Jordan River south of Galilee, it drops abruptly below 850 ft. below sea level, requiring the use of extra heavy 8-in. pipe and a relief station to reduce the pressure. A picked group of American welders, under H. S. Austin, of the Ajax Pipe Line Co., laid the line. It is coated, wrapped, and buried 30 in. beneath the surface in solid rock along much of the route. It crosses four large rivers and wide stretches of alkaline soils. Twelve pumping stations are employed, three of which are double east of the bifurcation. Each single station houses three 500-hp. crude-burning deisel engines flexible-coupled to reciproratirig pumps. Each pumping unit is capable of handling a minimum of 21,000 bbl. of oil, giving the entire system a

Jan 1, 1935

By Robert H. Hafner, Irvin R. Kramer

IN recent years considerable interest has been shown in surface-alloyed metals, particularly those of chromium (chromized steels), which have excellent corrosion [ ] resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method' employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high temperatures of 1200° to 1400°C. (2200° to 2550 F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- [ ] mon salt, and heated for approximately three hours at 930° to 1040°C. (1700° to 1900°F.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900° to 1000°C., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1942

By Robert H. Hafner, Irvin R. Kramer

In recent years considerable interest has been shown in surface-alloyed metals, particnlarly those of chromium (chromized steels), which have excellent corrosion resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high tem- peratures of 1200º to 1400ºC. (2200° to 2550°F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- mon salt, and heated for approximately three hours at 930º to 1040°C. (1700º to 1900ºF.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900º to 1000ºC., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a Chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1943

By Robert H. Hafner, Irvin R. Kramer

In recent years considerable interest has been shown in surface-alloyed metals, particnlarly those of chromium (chromized steels), which have excellent corrosion resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high tem- peratures of 1200º to 1400ºC. (2200° to 2550°F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- mon salt, and heated for approximately three hours at 930º to 1040°C. (1700º to 1900ºF.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900º to 1000ºC., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a Chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1943

By J. T. Ryan

SAFETY practice or the elimination of accidents in our coal mines is specifically a problem of management. It cannot be delegated to any governmental agency except that the various coal-producing states do and should have some minimum safety standard laws. However, the legislative method of attempting to control mine accidents is ineffective because of the delay between the necessity and the action. It will always be impossible to keep our various state mining laws up to date; and when the law says you must do a certain thin there is a tendency to do this and no more. Unless the scheme for setting up state regulations is so flexible that when a new hazard develops it can be immediately and adequately covered and the whole responsibility for accident elimination placed undivided on the

Jan 1, 1937

By Arthur Mitchell

POSSIBLY in no other of the non-ferrous mining districts of this country has the use and develop-ment of mechanical loaders been carried to such an extent as in the "lead belt" of Southeast Missouri. It has become apparent to the four mining companies in the district that it is imperative to apply satisfactory mechanical methods to the chief remaining stage of the entire operations-mining, milling, smelting and refining-in which manual labor is still largely used to handle material in process. With increasing wages and with the reduction of the metal divisor by the extension of mining into lower-grade orebodies, the shoveling cost per ton of lead produced has become relatively so large that in an effort to reduce it there is ample justification for considerable capital expenditure. Hand shovelers load about 18 tons of ore per shift and the average grade is less than five per cent. lead. Further, the ore is relatively heavy, about 21 cu. ft. to the ton when broken, and is often so coarse and so closely compacted after shooting that it requires much more block-holing, sledging, and muscular effort to shovel than, for example, does the cherty and more granular ore of the Joplin district or the finer ore in the headings of a drift mine. No mining company desires to pay for mere back muscles if it be economically feasible to avoid it, and labor saving machinery should be susceptible of operation by older employees, who are no longer capable of the more strenuous manual occupations.

Jan 4, 1923

By K. G. Wikle, J. G. Klein, W. W. Beaver

Consolidation of hydride process, electrolytic, calcium reduced, and comminuted thorium powder, as well as saw chips and lathe turnings, by vacuum hot pressing and by cold pressing-vacuum sintering was studied. The mechanical properties of the consolidated material in the extruded form are compared with those of wrought castings. AT present there little little industrial use for thorium metal, although it has some important though small scale applications in electronic equipment. Despite its high inelting point—about 1750°C —a low modulus of elasticity, 11.4xl0 si at 20°C;' relatively low mechanical properties coupled with a high density, 11.7 g per cu cm; and an unusually high chemical activity with normal atmospheres limit any structural applications. The metal is utilized as an alloying element principally in magnesium. Pure thorium finds utility as electrodes in gaseous discharge lamps such as the high intensity mercury lamp' because its low work function and high electron emissivity provide lower starting potentials and more uniform operating characteristics than other available materials. The metal is also found in photoelectric tubes used for the measurement of the ultraviolet spectrum." Thorium metal has been used in germicidal lamps of the cold cathode type as sputtered coatings on nickel in order to provide a low work function surface and a low starting voltage. Other applications have involved the radioactive properties of thorium for the production of ionized particles." The potential value of thorium is much greater than its present use pattern because of possible utility in the field of nuclear power. Th may be converted through nuclear reaction to a fissionable element U which should be capable of acting similarly to U in the g'eneration of atomic power. Thorium has been reported to be about three times as plentiful as uranium in the earth's crust, placing it in the order of abundance of lead and molybdenum." Thus, it is of interest in augmenting the potential supply of fissionable material for nuclear power. Because of its high melting point, thorium is usually produced as a powder through the calcium reduction of its oxide or thermal reduction of halides by sodium, magnesium, and calcium. It may also be produced in flake form by electrolysis of fused alkali or alkaline earth chloricles and fluorides. Therefore, powder metallurgy assumes importance in the fab- rication of thorium metal shapes. Furthermore, it is rather difficult to obtain pure thorium by melting, as the molten metal reacts readily with graphite as well as oxide, carbide, and nitride refractories. These contaminate the melt with oxides, carbides, and metallic impurities." The current investigation was undertaken to examine the fabrication of thorium by powder metallurgy methods which have been used for the commercial production of beryllium and other metals.' A sparcity of data concerning the comparative cold and hot compaction of thorium powders of different derivation existed. Therefore, all commercially available types were examined along with other experimentally produced thorium powders in order to round out the comparison of consolidated thorium powders with melted reguline metal. Review of the Literature By heating a mixture of ThC1, with potassium, Berzelius made the first thorium metal as an impure powder in 1828. Improvements in the basic process, increasing thorium assay to 99 pct, were made by several investigators including Arsem," Lely and Hamberger10 and Von Bolton." Calcium reduction of Tho, to make powders was investigated by Berger," Huppertz,'" Kroll," and Kuzel and Wedekind.'" A thorium powder produced by this method using a CaC1, fluxing agent assayed 99.7 pct, as reported by Marden and Rentschler.'" Compacted and sintered, this product was found to be ductile, and could be fabricated into wire and sheet. Improvements of the calcium reduction process were made later" wherein CaCl, was eliminated from the reaction, producing metal assaying 99.8 pct Th. Further work by Lilliendah118 howed that a coarser metal could be obtained by the substitution of ThC1, or ThOC1, for oxide with consequent advantage of stability to atmospheric reaction. Reports on the technology of thorium developed in Germany during World War II have been made by Espe."' Thorium powder of 99.5 pct Th was obtained by reduction of the oxide by calcium. Screening to —200 mesh, compacting with about 20 tsi, and sintering in vacuo at 1320" to 1360°C for 3 hr resulted in a porous sinter cake. The sinter cake was sufficiently ductile to be worked into bar, wire, and sheet which could be employed as electrode materials.

Jan 1, 1957

By AIME AIME

WILLIAM BAYARD HEROY, Director of the Institute since 1935 and Vice-President for the past year, has been active in both geological and engineering circles of the petroleum industry for many years. "Bill," as he is generally called, was born in New York City in 1883, and graduated from the department of geology at Syracuse University in 1909 with a Ph.B. degree. Immediately he joined the U. S. Geological Survey, where he established an enviable record during the next eleven years. While with the Survey he acted variously as chairman, chief, and advisory engineer for a variety of Governmental bodies, many concerned with power.

Jan 1, 1939

By P. L. Weston, S. E. Khalafalla

A systematic study was made by the Bureau of Mines on the effect of so me hypothesized accelerators for the process of wustite reduction in carbon monoxide. When small concentrations of promoter materials in the order of 0.69 at. pct were added to the reducible charge, the rate of reduction to iron was increased. Promotion phenomenon prediction was made in light of a suyface reduction mechanism with the aid of Vol'kenshtein's effect regarding the propagation of crystal lattice disturbances by small amounts of relatively larger interstitial ions. The acceleration produced by a typical promotor, such as potassiunl, increases with protnoter concentration up to a maximum, beyond which the reduction rate decreases. Concentration for maximum promotion depends on the nature and physicochemical properties of the promoter. The extent of reduction rate enhancement is found to be directly proportional to the atomic volume and electronic charge of the additive. DESPITE the enormous volume of literature on iron oxide reduction, very little is reported concerning additive or impurity effects on this important metallurgical process. The beneficial effect bf calcium compound additions on the reducibility of iron oxide sinters has been reported by Tigerschiold,1 vor dem Esche,2 and Edstrom. Doi and Kasai~ found that the addition of lime or limestone to iron ores helps to break up any unreducible compounds, such as fayalite or ilmen-ite. and thus free the combined iron for reduction. Schenck et al. 5 suggested that the increased reduction rate obtained when adding lime could be accounted for by the instability of wustite in the presence of lime. Acid-base slagging reactions resulted in wustite disproportionation according to The dicalcium ferrite formed will yield iron and calcium oxide during reduction. Regenerated calcium oxide dissociates more wustite. This mechanism has been used by Seths and white7 to explain their experimental results. Recently, Strangway and ROSS' attributed the calcium carbonate acceleration of iron oxide agglomerate reduction to increased porosity, both initial as well as that developed during reduction. Aside from calcium carbonate, or oxide, no other promoter was noted in the literature, except for a brief mention by Barrett and woodg on the effect of sodium carbonate and aluminate as activators for the hydrogen reduction of magnetite at 600°C. The present investigation systematically studied a host of other promoters, including calcium and sodium, in an attempt to elucidate the mechanism by which promotion takes place and to fit the results into a simple chemical model. To attain this goal, the effect of promoter physical properties, such as atomic volume, electronic charge, and concentration are related to wustite reduction kinetics in this paper. Wustite reduction to iron, rather than the overall hematite reduction, was chosen since this reaction is known to be the slowest, and hence the rate-deter mining step for the overall iron oxide reduction process. EXPERIMENTAL PROCEDURE Raw Materials and Their Preparation. The pure or impregnated wustite pellets were prepared from minus 400-mesh chemically pure hematite powders. A known weight of hematite was thoroughly and uniformly mixed with a calculated weight of the additive. The mixed paste containing 35 wt pct water was gradually heated from 400" to 1200° C and fired at 1200°C for approximately 4 hr in an air atmosphere. After cooling, the sinter was pulverized to minus 100 mesh and pelletized into minus 4- plus 5-mesh spheres. Pellets were fired, similarly to the paste mix, air-cooled, sized, and stored. An appropriate weight of the charge (20 g) was placed in a zirconia reduction tube maintaining a uniform oxide bed height of 1 cm and a cross section of 7.1 sq cm for all of the test runs. The samples were supported in the vertical reaction tube by a bed of fragmented insulating firebrick plus 3- to 6-mesh alumina beads. The hematite was then transformed to wustite by reduction with a 30 pct CO2-70 pct CO gas mixture at 1000°C in a globar furnace. Complete conversion to wustite was ascertained by a continuous infrared gas analyzer recording the CO-CO2 content of the effluent gas until no carbon monoxide was absorbed from the inlet gas, and inlet-outlet gas analysis remained constant for 30 min. The wustite sample was then reduced with 100 pct CO at 100WC. From the recorded data, an initial rate of reduction was determined by the initial slope of the graph percent reduction vs time. In order to estimate the accuracy of the data, five separate determinations of the reduction curve of pure wustite, under otherwise identical conditions, were performed. The maximum deviation from the average reduction at 14 min amounted to 2 2 pct reduction. This deviation corresponds to 3.8 pct variation based on the percent reduction of the sample. Aiiy impurity effect below the limits of this maximum deviation was considered a spurious result. If the effect exceeded + 4 pct, then it was considered as a positive one. Considerable care was exercised in determining the initial rate from the slope of the initial segments of the curve. Each reduction curve was examined separately on large graph paper and the best tangent to the curve at zero time was drawn. The slope of this tangent was taken as a measure of the initial fractional reduction per minute. Although the time required to reach 50 pct reduction may be of special practical significance, initial rate measurements are invaluable in fundamental studies. These rates provide a measure of the process kinetics on the initial

Jan 1, 1968

By W. E. C. Eustis

1st. THE fine iron ore is mixed with a sufficient proportion of fine coking coal, and is coked in any of the ordinary methods for making coke. The effect of this is to convert the iron oxide into sponge in such a shape that the usual trouble of oxidation is avoided. 2d. The resulting mixture of coke and sponge is melted down in an ordinary cupola, the coke furnishing more than sufficient fuel for that purpose. I may briefly point out here that in the first place the iron is sponged, and this sponge, as is well known, contain-, no phosphorus or silicon when the reduction takes place at a low temperature; and in the second place this sponge is melted down in a cupola in which there is no zone of reduction for phosphorus or silicon, and that con¬sequently the resulting iron should be free from both of these impu¬rities. 3d. The liquid sponge, now carburized, is run into an open-hearth furnace, where the requisite degree of hardness or softness is obtained by adding some of the fine ore, and the usual dose of ferronmanganose. I have merely given above the rough outlines of the process, but it is my intention, as early as possible, to bring the process more fully before the Institute.

Jan 1, 1881

By H. E. Nold

THIS paper is an effort to explain in a simple manner the fundamental principles involved in examining a clay deposit for both quantity and quality and in operating a clay mine, either open-pit or underground, so that the best quality of finished material can be made from the raw material available. The writer is aware that what is recommended in this paper is everyday practice in many refractories plants and in some other heavy-clay products plants, but observations made while visiting practically every clay mine in Ohio have convinced him that the practices herein discussed are not as widely used as their importance warrants. It is true that the problem of mining for quality is more acute in refractories plants than in most heavy-clay products plants, yet some of the latter are finding it profitable to pay more than ordinary attention to the selection and blending of their raw materials. It is hoped that this short paper may prove helpful to some who are now finding it difficult to produce a uniform product of as high quality as their clay deposit seems to warrant. The coordination of the work of the clay mine or pit with the manufacturing plant, to the end that the best product possible be made from the raw material available, presupposes a rather intimate knowledge of the clay deposit. The knowledge must include not only information of the amount of clay-available but also rather detailed information about both vertical and horizontal variations in quality of the clay. This information should cover three things: quality, quantity, and location.

Jan 1, 1929

By R. S. Archer

THE PROPER representation of equilibria involving graphitic carbon in the constitutional diagram of the iron-carbon system is admittedly an unsolved problem. The complete solution of the problem will probably require the establishment of more experimental evidence than is at this time available. The object of this paper is to present the author's observations on some of the phenomena in question and his interpretation of this and other recorded evidence. The chief of the recently disputed questions upon which the author has experimental evidence concerns the occurrence of graphitization at temperatures below the A1 point. In a paper1 presented at the September, 1919, meeting of this Institute, the following is found: "the results given would seem to indicate that the graphite eutectoid lies at a smaller value of carbon content than has been previously supposed. At least this is true unless there is either a marked formation of graphite eutectoid at these rates of cooling, or a decomposition of pearlite into graphite, both rather unlikely suppositions, but not impossible ones." In a discussion of this paper, H. A. Schwartz2 takes the position that the possibility of graphitization occurring below the A 1 point is an open question, but that complete graphitization (to less than 0.10 per cent. combined carbon) commonly occurs above this temperature. Another opinion from the malleable castings industry is found in a recent paper3 by Touceda: "Also the carbide of iron can be broken up into its two soft constituents at the temperature referred to. This temperature is called the critical temperature, or critical range, and for air-furnace hard-iron castings it is in the vicinity of 1440° F. It is the

Jan 2, 1920

By T. W. Atkins

ATHOUGH the magnesium industry in this country is about thirty years old, not until American industry began to amaze the rest of the world and confound our enemies with the extent and variety of our war production did the industry begin to come into its own. At the outset of the war, only three companies were producing and fabricating magnesium in this country. Today, about sixty companies are producing, casting, forging, extruding, rolling, and stamping this lightweight champion of metals. Experience in alloying, processing. and fabricating the metal gained during the war years is now being translated into hundreds of civilian peacetime applications. In no sense should magnesium be considered as a substitute for other metals. It has come into popular favor because If many unique properties in addition to is being the lightest known structural metal. These attributes are toughness, igidity, corrosion-resistance, and the ease with which it can be machined and worked. Magnesium is the third most abundant element in nature. Sea water, magnesite,

Jan 1, 1946

By W. E. C. Eustis

1st. The fine iron ore is mixed with a sufficient proportion of fine coking coal, and is coked in any of the ordinary methods for making coke. The effect of this is to convert the iron oxide into sponge in such a shape that the usual trouble of oxidation is avoided. 2d. The resulting mixture of coke and sponge is melted down ill an ordinary cupola, the coke furnishing more than sufficient fuel for that purpose. I may briefly point out here that in the first place the iron is sponged, and this sponge, as is well known, contains no phosphoras or silicon when the reduction takes place at a low temperature; and in the second place this sponge is melted down in a cupola in which there is no zone of reduction for phosphorus or silicon, and that con . sequently the resulting iron should be free from both of these impurities. 3d. The liquid sponge, now carburized, is run into an open-hearth furnace, where the requisite degree of hardness or softness is obtained by adding some of the fine ore, and the usual dose of ferromanganese, I have merely given above the rough outlines of the prows, bat it is my intention, as early as possible, to bring the process more fully before the Institute.

Jan 1, 1881

By AIME AIME

ALMOST as many attended the annual dinner this year as last, when the presence of Mr. Hoover was such an attraction that almost two-thirds more than had ever attended before were present. Only by putting the late comers at tables in the balcony could everybody be accommodated. Past President De-Golyer was the toastmaster and in opening the post-prandial exercises referred to the regrettable fact that this was the last of the long series of dinners which have been held at the Waldorf, as the hotel will be torn down to give way to an office building before another year. To the delight of the gathering "Oscar" appeared and, in a delightfully brief but characteristic speech, referred to the long association that had existed and hinted that a new Waldorf-Astoria may arise, where the Institute could continue to gather annually in an enlarged replica of the room they had met in so long. Before taking up the presentation of the medals, Mr. DeGolyer referred to the Institute's "Legion of Honor," the 34 men who have been members continuously for over fifty years. For various reasons only five of them, W. S. Ayres, F. G. Corning, Henry D. Hibbard, A. F. Schneider and Arthur Thacher, could be present. They were all seated at the speaker's table, and W. S. Ayres, 56 years a member, as the dean of the group, was called on to respond for them all. He said: "The introduction I have just received would indicate that this particular group of men to which I belong is considered by the chairman to be a group of real antiques. Possibly you are questioning the accuracy of his judgment. I hope you are, although there may be some first-sight evidences tending to substantiate the view held by the chairman.

Jan 1, 1929

By T. W. Guy

THE increased moisture due to water¬spraying for coal dust control is of interest even for mines from which the coal is to be wet-washed before screening, because in many cases wet coal dust materially decreases the loading efficiency of men an equipment at the faces. It also causes serious increase in the normal wear and deterioration of all equipment with which it comes in contact. It is important to the consumer if it increases his as-receive moisture. No attempt will be made in this paper t cover the entire subject of water-spraying of coal for dust control. It will be confine to discussion and data on (r) percentages c dust in bituminous coals, (2) moisture increases due to spraying for dust control in mines or plants by methods which have proven satisfactory for periods of one to five or more years, and (3) a few suggestions for research. SIZE AND PERCENTAGE OF COAL DUST The U. S. Bureau of Mines1 classifies a coal dust all bituminous coal passing 20-mesh sieve (0.0328 in. square opening; The percentage of such dust to be found is ROM coal, of course, varies widely wit. the characteristics of the seam, and with the methods used in the mining and in the preparation of the coal. ROM screen analyses of 12 U. S. coals selected at random from personal files given in Table I show: A few other screen analyses examined indicating 40 pct or more of 2o-mesh X o dust in 3/8 in. X o-sizes were not included because of uncertainty that they were representative. The number of results in Table I is not sufficient to give a reliable estimate of the average, or of the range to be expected, but it indicates that in every case the coal dust is a relatively large percentage of the total ROM coal, and, of course, a progressively larger percentage of resultants as the larger sizes are separated for marketing.

Jan 1, 1948

By Wen H. Su

Multiple seam mining and its associated problems are very serious in Southern West Virginia where poor planning or lack of knowledge in seam interaction often results in complete loss of coal properties. Several measures have been proposed to alleviate the interaction problems under various multiple seam conditions, but few of them are specific in terms of mining plan. Two parallel approaches are adopted for this paper. One is field investigation which consists mainly of mine site visits and gathering of data. The other is the two-dimensional finite element simulation of mine workings using the data gathered as input. Two typical cases which represent the past and present multiple seam mining practice in West Virginia were investigated. Much attention is focused on the interaction problems experienced and the important parameters controlling interaction. Several key parameters controlling interaction in multiple seam mining were analyzed. Proper mining plans, by which the interaction problems can be minimized, are proposed for the individual cases after a better understanding of the interaction mechanism was realized through finite element analyses.

Jan 1, 1984

By George Rice

THE subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on bumps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free' from folding and faulting.

Jan 1, 1935

By R. B. Adair, J. S. Browning

The laboratory batch and continuous flotation pilot plant tests demonstrated the technical feasibility of recovering high grade mica concentrates from weathered mica pegmatite ores of Alabama and Georgia. The research indicated that combinations of anionic and cationic collectors may be used effectively for flotation of fine size mica from weathered pegmatite ores. In continuous tests, concentrates containing 98.5% mica were obtained from the Georgia pegmatite ore; the Alabama pegmatite ore concentrates contained 98.4% mica. The recoveries were 91 and 89% respectively. INTRODUCTION The principal uses of fine ground mica are as a filler in wallboard joint cement, as a filler and surface coating for roofing, as an ingredient in paints, and in oil well drilling mud. The mineral has other uses in the manufacture of rubber, wallpaper, plastics, welding rods, electric insulation, house insulation, and textiles, and as an annealing agent in metal treatment. In recent years, more than 99% of the domestic mica produced has been scrap and flake mica (mica which does not meet specifications for sheet mica and is used for producing fine ground mica). There has been a continued increase in mica production for several years, the 1963 production of scrap and flake mica totaling 117,251 tons.1 Ground mica is obtained primarily by crushing and milling pegmatites and schists. To a lesser extent, mica is produced as a byproduct of kaolin washing and feldspar and spodumene flotation operations. The processes used in recovering mica by crushing and milling pegmatites are generally simple, consisting of various combinations of alternate roll crushers and trommel screens that separate the mica and gangue at screen sizes coarser than 6-mesh. As these processes are designed to recover only coarse mica, high losses in the plant rejects are common. Large tonnages of tailings from the crushing and screening plants have been accumulated in a number of areas. Methods for treating such products were developed by the Bureau of Mines in 1941,2 but have not been generally applied. More recently, mica flotation research has been completed and published by the Bureau of Mines.3 These methods required complete removal of 150- to 200-mesh materials from the flotation feed with consequent fine mica losses. Later, the Bureau of. Mines investigated methods for-recovering fine size mica from pegmatite ores after desliming sufficiently to remove clay materials, but not so drastically as to remove the fine sands. This report summarizes the results of these studies. The process developed was effective on pegmatite ores from two locations and should be applicable to the commercial treatment of other mica-bearing pegmatite ores and fine rejects that have been accumulated at various mica-milling operations. DESCRIPTION OF ORES The ores used in the investigation were obtained from the Dixie Mines, Inc., Heflin, Alabama, and the Ruberoid Corporation, Hartwell, Georgia. The sample from Alabama contained muscovite and quartz, with a high percentage of clay, and minor amounts of biotite, kaolin, limonite and tourmaline. The mica in the ore was essentially all minus 4-mesh in size and was free of attached mineral grains. The Georgia sample contained muscovite and quartz, with minor amounts of biotite, kaolin, and limonite. The mica in the ore, which was essentially all minus 4-mesh, was liberated. Petrographic analyses of the two samples are given in Table I. THE ANIONIC-CATIONIC MICA FLOTATION METHOD Previous investigators2,3 have reported that complete desliming of mica ores at 150- to 200-mesh was required prior to flotation with cationic collectors to obtain satisfactory selective separation of the mica from the other mineral components. Numerous tests were made at the Tuscaloosa Metallurgy Research Center to determine if some reagent combination could be used to selectively float finer size mica without complete desliming. The investigation led to development of a process using a simple reagent com-

Jan 1, 1967