Search Documents

By Ionel Gardescu

IN connection with some of the experiments carried out by the writer on the behavior of gas and oil in a sand reservoir,1 an interesting phenomenon was observed which may throw some new light on the problem of recovery of oil from a natural reservoir. The experiments are intended to show the effect of the surface area of the occluded gas masses, originally present in a reservoir, on the further evolution of gas from the oil and its consequent effect upon the rate of production of oil. The apparatus used in the experimental work is shown in Fig. 1. It consists primarily of a sand reservoir R and a displacement chamber D, which is used to induce small variations in volume. The reservoir and displacement chamber form a unit, and a lowering of the plunger D is equivalent to increasing the volume occupied by the oil and gas in the reservoir. The reservoir was first filled with dead oil and maintained under pressure until it was ascertained that most of the free gas had gone into solution. The volume of free gas present in the reservoir was computed from the coefficient of compressibility of the fluids by means of the dis-placement chamber D, reading to 0.005 c.c. and a special gage J reading to 0.02 lb. per sq. in. The oil was saturated with gas under pressure in reservoir S by circulating the oil for a long period of time through the gear pump B. Subsequently, the saturated oil was circulated through the sand reservoir following the circuit S6, B, S5, R4, the sand reservoir R, R1, R2, F4, F1, back to reservoir S. In the following experiments the sand reservoir R was filled with gas-saturated oil at a pressure of 415 lb. per sq. in. with no free gas present. This was ascertained by. closing off all the outlet valves, and determining the coefficient of compressibility of the system by means of the dis-placement chamber D.

Jan 1, 1932

Robert T. Hill, Washington, D. C.: Having studied very minutely the geology of the district referred to by Prof. Branner, I beg to state that his quotation of my classification of the Cretaceous deposits of Arkansas is not the one which I originally gave,* nor is it the one which has since been published and is now generally accepted.? I did not assign ally of the Cretaceous formations of Arkansas to the " middle Cretaceous,"

Jan 1, 1898

Feb. 5. Society for Applied Spectroscopy, 6 pm, supper, Tosca's; 8 pm, meeting, Socony-Vacuum Training Center, 63 Park Row, New York. Feb. 6, AIME, Chicago Section, Chicago Bar Assn., 29 S. La Salle St., Chicago. Feb. 18-21, AIME, annual meeting, Hotel Statler, New York. Feb. 19, Michigan College of Mining and Technology, alumni reunion, Skytop Room, Hotel Statler, New York. Feb. 21, AIME, Utah Section, Newhouse Hotel, Salt Lake City. Feb. 28, Bituminous Coal Research, Inc., annual meeting, Edgewater Beach Hotel, Chicago. Mar. 3-7, ASTM, spring meeting and committee week, Hotel Statler, Cleveland. Mar. 5, AIME, Chicago Section, Ladies' Night, Chicago.

Jan 1, 1952

By F. M. Smith, R. H. Moore, J. R. Morrey

Electrodiffusion in y cerium reported by Henrie has been confirmed and a Preliminary estimate made of the relative rates of electrodiffusion of iron, cobalt, and nickel. These diffuse to the anode at rates decreasing in that order. In addition, copper and manganese exhibit slow, but detectable, diffusion to the anode and molybdenum exhibits detectable diffusion to the cathode. The electrodiffusion of carbon, .zirconium, antimony, magnesium , and silicon in y cerium could not be detected. Iron and cobalt diffuse in y cerium at rates proportional to the current density and with no apparent dependence on temperature. Decreasing polarization of iron and cobalt with increasing temperature, which cancels the expected rate increase, would account for this behavior. The electrodiffusion rate of iron in y uranium and in E plutonium has been measured. Diffusion of iron is anode-directed. Tin was found to diffuse to the cathode, in y uranium, at an appreciable rate. In all of these solvent metals, negative ions diffuse to the anode and positive ions to the cathode. The potential field effect appears to account satisfactorily for these results. FROM early experimental work summarized by Jost1 and Seith,2 the driving force for electrodiffusion was attributed to the potential field acting on ions in a metal. More recently, Heuman,3 Wever,4 and Huntington5 have shown that momentum interchange between conduction electrons and mobile entities in the metal contributes to electrodiffusion. Electron momentum interchange is anodically directed and the direction of diffusion resulting from the field force is dependent upon the charge on the diffusing entity. These two effects may either reinforce or oppose each other. Glinchuk6 has pointed out that momentum transfer in defect conductors should be cathode-directed and this appears to be the case as demonstrated by wever's4 work on iron. Barnett's7 work, on the other hand, indicates that, even in defect conductors, electrons show a negative E/m ratio when accelerated with respect to the lattice and should lead to anode-directed momentum transfer. In discussing this problem, Wever and seith8 suggest that defect electrons interact preferentially with activated ions so as to allow a net movement toward the cathode while still maintaining an electron momentum transfer in the anode direction. Williams and Huffine9 and Henriel0 have demonstrated that electrodiffusion may be useful for purification of yttrium and cerium. In yttrium, Williams and Huffine note that movement of several metallic impurities toward the anode is in keeping with observations in most other metallic systems and indicates that yttrium remains a normal electronic conductor at least to 1230°C. Close inspection of their data shows, however, that oxygen, nitrogen, and the transition elements diffused toward the anode, while nontransition elements diffused toward the cathode. This suggests that potential field effects may have been appreciable. The present work was concerned with the applicability of electrodiffusion as a technique for purification of plutonium, but, because of the obvious hazard inherent in work with this metal, experiments to develop the technique were carried out using cerium and uranium. The results of electrodiffusion measurements on these metals and on plutonium are reported here. EXPERIMENTAL The metal specimens prepared for this work were 6 in. long, 1/4 to 1/2 in. wide, and 1/16 to 3/32 in. thick. The uranium specimens were machined from a bar which analyzed 310 ppm Fe and the electrodiffusion of iron was followed by spectrographic and by chemical analysis. Cerium and plutonium specimens were cut from sheet rolled from ingots obtained from molten salt-metal equilibrations during which radioactive tracers were introduced. The electrodiffusion of the tracers was subsequently determined by counting methods. The specimens were electrolyzed between nickel electrodes containing resistance heaters used to equalize the specimen and electrode temperatures, thereby reducing thermal gradients. The temperature of the electrodes adjacent to the ends of the specimen was measured with chromel-alumel thermocouples which were connected to the heater controls. The surface temperature of the specimen at a point midway between the electrodes was measured with a sapphire rod pyrometer, the output of which controlled the dc power supply. This assembly was enclosed within an evacuable chamber containing a quartz viewing window. The temperature of the specimen over its entire length could be scanned with a portable pyrometer through

Jan 1, 1965

By L. J. Boucher

The beneficiation process at Northampton is described and reasons are given for installing a flotation plant. The economics of running the plant, the difficulties of operation, and subsequent remedial action are discussed. CEMENT rock from a quarry operated by the Northampton plant1, 2 of the Universal Atlas Cement Co. has a relatively low average CaCO³ content. To meet specifications required for cement manufacture it was formerly necessary, over succeeding years, to add increasingly larger amounts of high-lime, low-alumina rock, which was obtained from a quarry operated by the company at a point along the New Jersey-New York state border, 79 miles from Northampton. Previous to 1940, 8 pct of total kiln feed consisted of high-lime rock. From 1940 to 1943, this figure jumped to 13 pct. Today it would be necessary to use 18 pct of this high-lime to meet current specifications. Increasing transportation costs made this an expensive operation. In addition, this high-lime rock quarry was contaminated with granite and high magnesia pockets. As there was no available high-lime rock in the Lehigh Valley, it was decided in 1936 to install a pilot plant where experimental work was done on processing local cement rock with flotation and burning the resulting product in a small kiln. This plant was in operation for six months and at the end of that period a suitable method of flotation had been established. From these studies it was also found that if the proportion of shipped-in rock rose slightly above 10 pct it became economically advisable to use the flotation process. It is the object of this paper to present briefly the operation of the flotation system at the Northampton plant. It seems advisable to comment on the raw material used in this process. The Northampton quarry lies geologically in what is known as the Jacksonburg formation of Trenton limestone.' In Pennsylvania this extends in a southwesterly direction from Portland, through Nazareth, Bath, and Northampton and across the Lehigh River to Ormrod. This argillaceous limestone was formed from marine deposits laid down during the early Ordivician period when a shallow sea covered most of Pennsylvania. Carbonaceous matter in the original deposit formed graphitic carbon under later metamorphic forces. From this graphite the cement rock of the Lehigh Valley derives its dark color. Most of the graphite must be removed before lime flotation can proceed. The quartz in this rock is desirable from the chemist's point of view, as it furnishes him with a form of silica necessary in the calcining process, but its abrasive properties damage pumps and piping. Aluminum silicates of potassium, sodium, iron, and magnesium are found in the form of sericite. Cal-cite averages from 69 to 76 pct. Iron in the form of iron pyrites is also present and has no deleterious effect. Talc is present in minute quantities. The

Jan 1, 1954

By John V. Beall

Copper production in the. United States in 1972 amounted to 1,658,000 tons according to the USBM. This figure is up over 1971 but falls below 1970 production of 1,719,101 tons. This report is essentially about the status of copper mining operations in the U.S. and is an update and expansion of the report "Southwest Copper-A Position Survey" published in [A=], October 1965. At that time, the trend was toward using larger equipment to mine lower grade ore and toward the expansion of dump leaching practice. That trend continues today but, it is overlain by intensive activity to comply with existing environ¬mental legislation and uncertainty over proposed revisions of venerable laws governing mining. In the U.S. today there is, practically speaking, no excess smelting capacity so that expansion of copper production through the startup of new mines is inhibited. Owners of a large undeveloped orebody would have to decide before going into production whether to sell the concentrates offshore, which has many problems, whether to try one of several unproved chemical processes for producing refined metal from concentrates or embarking on the construction of a traditional pyrometallurgical plant in the face of considerable uncertainty over the pollution standards that eventually must be met. The situation is such that not only is the present rate of U.S. copper production threatened but the ability to meet projected increased demand in the years ahead may have been severely retarded.

Jan 4, 1973

By W. E. Forsythe

Different forms of optical pyrometers are discussed and the advantages and disadvantages of the different types for measuring high temperatures are pointed out. These advantages and disadvantages lead to the selection of the disappearing-filament type of optical pyrometer for most work. Attention is directed to the necessity for the use of a monochromatic screen with a pyrometer, which leads to a discussion of the meaning and use of the effective wave length of the screen. Methods of calibrating the optical pyrometer are outlined and it is shown that an optical pyrometer can be calibrated just as definitely as any other temperature-measuring device. Accuracy tests are included, in which it is shown that excellent results can be obtained by even untrained or slightly trained observers with this form of optical pyrometer. The various corrections that are necessary in this kind of work are indicated, including corrections for stray light, for absorption of windows, of smoke, and so forth. The troublesome problem of measuring the temperature of bodies that do not radiate like a black body is discussed and the corrections for reducing such readings to the true temperature are given for a number of different materials. Introduction The fundamental idea of temperature depends upon our temperature sense and bodies are said to be hot or cold depending upon the reaction of our hands or some other part of the body to the heat from the source investigated. For measuring the temperature some instrument must be devised, since the temperature of the source studied is apt to be so hot as to greatly injure any part of the body that comes near it, to say nothing about direct contact with it. Definition of Temperature.—The temperature scale is based upon two fixed points, the temperature of freezing water and the temperature of boiling water. This temperature interval, depending upon the scale

Jan 1, 1936

By W. E. Forsythe

Different forms of optical pyrometers are discussed and the advantages and disadvantages of the different types for measuring high temperatures are pointed out. These advantages and disadvantages lead to the selection of the disappearing-filament type of optical pyrometer for most work. Attention is directed to the necessity for the use of a monochromatic screen with a pyrometer, which leads to a discussion of the meaning and use of the effective wave length of the screen. Methods of calibrating the optical pyrometer are outlined and it is shown that an optical pyrometer can be calibrated just as definitely as any other temperature-measuring device. Accuracy tests are included, in which it is shown that excellent results can be obtained by even untrained or slightly trained observers with this form of optical pyrometer. The various corrections that are necessary in this kind of work are indicated, including corrections for stray light, for absorption of windows, of smoke, and so forth. The troublesome problem of measuring the temperature of bodies that do not radiate like a black body is discussed and the corrections for reducing such readings to the true temperature are given for a number of different materials. Introduction The fundamental idea of temperature depends upon our temperature sense and bodies are said to be hot or cold depending upon the reaction of our hands or some other part of the body to the heat from the source investigated. For measuring the temperature some instrument must be devised, since the temperature of the source studied is apt to be so hot as to greatly injure any part of the body that comes near it, to say nothing about direct contact with it. Definition of Temperature.—The temperature scale is based upon two fixed points, the temperature of freezing water and the temperature of boiling water. This temperature interval, depending upon the scale

Jan 1, 1936

By P. G. Shewmon, F. N. Rhines

THE determination of the self-diffusion coefficient of magnesium has been made possible recently by discovery1-1 of a radioactive isotope, Mg28 having a half-life of 21.3 hr,1 and subject to manufacture in useful quantity. In the present research this material was condensed from the vapor phase upon a surface of high purity magnesium. The progress of diffusion of the tracer atoms into polycrystalline magnesium was followed by machining layers and measuring the change in the intensity of radiation as a function of the distance of each layer from the surface. The self-diffusion coefficient was found to be 2.1 X 10-8 sq cm per sec at 627°C, 3.6 X 10-9 sq cm per sec at 551°C, and 4.4 X 10-10sq cm per sec at 468°C; the activation energy is about 32,000 cal per mol. Experimental Procedure Since there was no other published measurement of a diffusion velocity in any magnesium-base material, is was necessary to employ a number of new experimental techniques. The short half-life of Mg28 made it necessary to complete the entire experimental procedure within three or four days. This meant that the work had to be done where a cyclotron was readily accessible and that all operations, prior to the diffusion heat treatment, had to be so designed as to minimize their time requirements. Unusual problems were imposed also by the chemical reactivity of magnesium, its high vapor pressure, and the fact that no satisfactory method for elec-trodepositing magnesium on magnesium is presently available. Finally, the machining and handling of the easily air-borne radioactive-magnesium chips involved certain health hazards, resulting in the need for further experimental restrictions. Preparation of Mg28 The Mg28 was produced in the Carnegie Institute of Technology syncrocyclotron by the neutron spallation of chlorine.5 his involved bombarding a 2 gram crystal of high purity NaCl with a beam of 350 mev protons for a period of 2 hr, after which the crystal was dissolved in warm water and the Mg28 was concentrated and purified by chemical means (see Appendix). About 50 microcuries of Mg28 thus were obtained in the form of magnesium oxinate (8 hydroxyquin-olatc?), which was ignited in air to produce MgO. This in turn was reduced to magnesium metal vapor, by the method of Russell, Taylor, and Cooper," in the vacuum apparatus shown schematically in Fig. 1. Here the essential part is a tantalum ribbon, slightly dished to receive the MgO. The ribbon, pre- viously outgassed at high temperature, is heated to about 1700°C by passing an electric current through it, whereupon tantalum oxide is formed, magnesium vapor is released almost instantaneously, and condensed partly upon the diffusion sample. Diffusion-Sample Preparation: Hot-extruded magnesium rod, 21/32 in. round was used in making the diffusion specimens. The magnesium analyzed as follows: 0.004 pct Al, 0.027 pct Fe, 0.040 pct Mn, 0.0004 pct Cu, 0.0002 pct Ni, and less than 0.01 pct Ca, 0.0004 pct Pb, 0.0011 pct Si, 0.001 pct Sn, and 0.001 pct Zn. A brief study of the crystal texture of this material revealed a sharp fiber texture with the (001) plane roughly parallel to the extrusion axis. Cylindrical samples 1/2 in. long by 5/8 in. were machined from this rod, the end faces dressed on 3/0 emery, and lightly etched with 20 pct HC1 in water. These samples then were annealed for at least twice the intended time of diffusion, at the intended diffusion temperature, in order to stabilize the grain structure at about 1 mm average diameter. The annealing treatments were conducted in argon in the same apparatus and in the same manner as the subsequent diffusion treatments, which will be described presently. Thus, a strain-free plane surface was produced, but there remained a layer of MgO which had largely to be removed before the layer of Mg28 was deposited. Most of this layer was taken off by two light passes over 3/0 emery paper. The balance of the oxide and a thin layer of metal were then removed by etching 5 to 10 min in 4 pct nital (4 pct HNO3 and 96 pct ethyl alcohol) made with absolute alcohol. There followed immediately three quick rinses in: 1-49 1/2 pct methanol, 49 1/2 pct acetone, and 1 pct formic acid, 2-50 pct methanol and 50 pct acetone, and 3-pure benzene. This procedure is essentially that of Sturkey.7 The resulting surface, which was of almost elec-tropolished brightness, remained plane and was free of cold work. It could be kept clean by storing under benzene, or in a desiccator; short exposure

Jan 1, 1955

By John Griffen

THEORY HYDRAULIC classification as explained by Rittinger and others was largely restricted to conditions wherein the free-falling velocities of the particles were conceived as governing the separations effected (see chapter 9). The laws governing classification under free-falling conditions have been summarized by Chapman and Mott as follows: 1 Nomenclature r represents, in a particle of irregular shape, the round-hole screen through which the particle would pass, or some other linear dimen¬sion of the particle equivalent to d, the diameter of a sphere. s, the specific gravity of the particle. 1, the specific gravity of the water used as a medium. K, a constant. W, the velocity of the water. In an Upward Current of Water 1. A particle will move upward if [W > KVr(s-1)] and, by suitably regulating the speed of the water current, the larger and heavier particles may be made to fall downward against the current, leaving the smaller, lighter particles in suspension in the current. 2. Particles such that [T1= s2-1] cannot be separated in an upward-current classifier with any one velocity of current. Coal particles having a specific gravity of 1.35 cannot be separated from refuse particles of 2.5 sp. gr. Unless 2.5-1 the ratio of diameters is less than [1.35-1 or 4.3 to 1,] and the raw coal must be screened to size limits within this ratio if they are to be separated. Cone¬-shaped vessels or vessels of other shapes that allow the use of&apos; different velocities of current at different points in the flow are used to modify this limitation. 3. During the initial stages of motion, coal particles ascend more rapidly than refuse particles of the same size. 4. A particle will ultimately fall if [W < KVr(s-1).] If particles of

Jan 1, 1950

By Julian Avery

IN its dual role of pig-iron smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus. Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary pur-pose. During the past 10 years or more, improvements in blast-furnace technique and economy have, in fact, been directed primarily to increasing efficiency in the use of the reducing power of the gases produced by com-bustion of coke at the tuyeres, to reduce iron ore within the furnace. The net over-all result is a decrease in the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently more than offset in value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements. The purpose of the present paper is to suggest that, while progress has been made in this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all economy of a different order of magnitude than results thus far obtained by the use of other expedients. The present argument is based in large part upon the hypothesis that the effi-ciency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss can be successfully attacked by increasing the over-all pressure; i.e., the "top pressure" under which the furnace is operated. It is indicated that pressure operation may also be expected to result in concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity.

Jan 1, 1938

Jan 1, 1931

By P. W. Rainier

THE Chivor emerald field is situated on the eastern slope of the Andes in the Department of Boyacá, at an elevation of about 8000 ft. above sea level. It overlooks the Llanos (plains) of the Orinoco and is watered by many streams flowing into the Rio Meta, the Orinoco&apos;s largest tributary. The Rio Meta is navigable from the Orinoco to a point within about 50 miles of the Chivor district and may eventually prove to be the reasonable outlet for the future development of this part of the country. The topography of the district is extremely rugged and mountainous (Fig. 1), the difference in elevation between two points on a mining claim 1 km. square being sometimes as much as 4000 ft. The ground is covered with dense forest growth and the available timber is suitable and sufficient for mining purposes, but it is becoming gradually depleted by Indian clearings as the country around the mines becomes settled. The many streams combined with the rough topography give good possi-bilities for hydroelectric power. The center of population nearest to Chivor is Bogota, the capital of the republic and a city of some 300,000 inhabitants; the distance is two and one-half days&apos; travel. The first stage of the journey from Bogota, is accomplished by rail to Chocontá, some 4 hr. travel. From Chocontá the journey is made in the saddle, one night being spent in Guateque. The latter is a small town and the nearest post office to the mines, being some 10 hr. ride distant. The roads are mere bridle paths, in parts hazardous and almost impassable in the wet season. All supplies brought to the mines, other than those produced locally, are carried by pack mule; mule freight from Chocontá costs 3 centavos1 per pound. The climate of the Chivor district is healthful and bracing. The wet season begins in March and concludes in November, the remaining months being dry. The annual precipitation is about 150 in. The temperature throughout the year is nearly constant, varying from about 45° F. to about 65° F. shade temperature. The rains are cold and unpleasant, and for the greater part of each day in the wet season the country is shrouded in dense mist. A fire can with comfort be kept burning in a living room all the year round. There are a few slight

Jan 1, 1929

By J. A. Wilcox

A NEW LINE of specialists has arisen as a result of the trend toward labor socialization and collectivism in all branches of industry. These men are the ones who will govern the destiny of many companies and the labor policy of our government in coming years. They must be men of integrity and of rather exceptional qualifications; men who can foresee the trend of labor relations with business, and who are willing to sacrifice the immediate fruits of technical training for manual labor and study. They must take their place in industry, not with the idea of following the orthodox line of advancement, but knowing that they must stay at the bottom until they have learned to understand the viewpoints, the work, the advantages and the disadvantages of each classification of labor. They must not be of a radical nature or become easily biased, and they must study. You will say I am looking for a superman and in one sense that is true, but the business man and our government are both in the market even now for this type of man, and with the proper training and background, many of our young technicians can readily enter this field of work.

Jan 1, 1942

By L. L. Swift

AT the present time there are four base metals being used for automotive bearing alloys. Of course there are numerous variations in the amounts of alloying elements added to each base metal and nearly all of these alloys have the conventional, if not classical, duplex structure; that is, they are composed of a hard constituent embedded in a soft matrix. The well-known theory is that the former will wear well, while the latter will be plastic enough to allow the bearing to be broken in and conform to the contours of the shaft. The requirements of the modern bearing have been most aptly described by W. M. Corse: In order to meet the engineering demands of today a good bearing metal must be able to carry the weight of the shaft and stand up under steady or suddenly applied loads, or even blows in some types of service. A certain amount of plasticity is desired to compensate for minute irregularities in the shaft or bearing surface, and to permit yielding, thereby avoiding dangerous stresses in bearing and shaft and preventing overheating and rapid wear of parts. Less plasticity is required in a bearing metal if the surfaces of bearings and journals are machined accurately, aligned, and kept in alignment. It is desirable, of course, that a bearing metal have a low coefficient of friction. Under most operating conditions the friction depends on the unit pressure of the bearing, the speed, the temperature, and the properties of the lubricant. A good bearing metal must have a low rate of wear to reduce the necessity for frequent replacements, and adjustment of the bearings. It must wear more rapidly, however, than the journal or shaft running on it, because replacement of the journal or shaft is more difficult and costly than replacement of the hearing., The hardness of, the bearing alloy is a property closely related to several of the foregoing. With a duplex microstructure, the measurement of hardness with any of the usual commercial devices means little. The Bierbaum method of measuring the hardness of the individual constituents was developed to, fill this need. MICROCHARACTER The Bierbaum microcharacter2.3 measures the scratch-hardness of a solid by pulling a weighted diamond point over the surface. The diamond point is ground. so that it is the corner of a cube, and mounted

Jan 1, 1938

By J. F. Abel

It can be concluded that rock mechanics instrumentation, geologic mapping, and operations research in combination will produce an accurate estimate of tunnel support requirements for establishing a steel-set load prediction model. This estimate can be used to increase safety and to reduce tunneling costs. Unnecessary supports can be eliminated; overloaded or insufficient supports can be replaced on a more scientific basis than previously possible. Only a limited number of measurements are required to develop a steel set load prediction model. The results of this study can be applied generally; but, every tunnel must be considered as a separate problem. The construction and geologic variables which were found to be significant in the prediction of rock loads in this tunnel were: steel section modulus, set blocking points, percentage of alteration, relative degree of faulting, relative water condition, distance to the nearest fault, and average joint spacing. INTRODUCTION A combined engineering geology and rock mechanics program was performed throughout the Straight Creek tunnel pilot bore in Colorado in order to develop a technique for estimation of steel tunnel support loads. The technique involves the construction of a statistical model from measured steel set loads, geologic and construction factors. The aim of the investigation was to produce a set of charts, based on these factors, which could be used by a trained man equipped with a hand lens and measuring tape, to specify a safe and economical steel size and set spacing. In order to be of practical value the measured parameters had to be rapidly measurable and capable of quantification. It was apparent from the beginning that quantitative values for many of the geologic factors would have to be arbitrary. It was impossible to ascertain in advance which of the readily determi-nable geologic and construction factors significantly affect steel set loading. As the investigation progressed the number of observations was systematically reduced in order to determine the minimum amount of data which would be necessary for a significant mathematical model. This paper presents an analysis of all the variables measured at each instrumented steel set. The statistical significance of the measured variables was determined. On the basis of this determination, a mathematical model was constructed and charts were prepared to select and space the steel tunnel supports at any given point in the tunnel. Once the effect of geologic and construction factors on set loading is sufficiently established, it is possible to exert close control over the selection of steel tunnel support size and spacing. The magnitude of this rock mechanics program can be appreciated when it is known that there were 44 instrumentation stations for which steel set loads were measured. For each of these sets there were three construction variables recorded, and nine geologic parameters determined (Table I). A rough approximation of the cost for both the collection and reduction of the data would be $50,000. This is in addition to the cost of geologic mapping.

Jan 1, 1967

By J. J. Pye, J. B. Drew

Mzasurements of the surface diffusion coefficients of metals have been made. Diffusion profiles for the Ag-Ag system were obtained by means of a radioactive point source and a precision auto-radiographic technique. The activation energy for silver self diffusion (=8.1 kcal per mole) is lower than that previously reported (-10 kcal per mole) on poly crystalline wire by Nickerson and Parker. The bresent data indicate an effect due to parasitic volume diffusion at temperatures above 500°C. RELATIVELY few measurements have been made of the surface self-diffusion coefficients of metals. Nickerson and arker&apos; measured the diffusion of silver over the surface of poly crystalline wires and estimated that the activation energy was 10.3 kcal per mole. Winegard and chalmers2 carried out measurements on both polycrystalline and single crystal surfaces but did not report a value of the activation energy. They found, however, that at temperatures between 250" and 400°C the diffusion coefficients were on the order of lo-&apos; sq cm per sec and that there was an acceleration of the migration of silver on the polycrystalline sample when a change of surface shape occurred. Winegard and Chalmers used an autoradiographic technique, hereafter designated ARG, and Nickerson and Parker used a surface scanning geiger counter in order to determine the diffusion profiles. More recently, Hackerman and simpson3 measured the surface self-diffusion coefficient of copper at a single temperature (750°C), and the value of the diffusivity (- 10-5 sq cm per sec) is in agreement with that given by jostein from his thermal grooving measurements. This paper reports the results of an investigation of the surface self-diffusion coefficients of silver over a large temperature range and describes the adaptation of autoradiographic (ARG) techniques for the determination of diffusion profiles obtained from a radioactive point source. EXPERIMENTAL PROCEDURE The experimental procedure is a modification of the method employed by Hackerman and simpson3 in their measurements on copper. A brief description of their technique is as follows: A radioactive needle which sinters to the surface during the diffusion an- neal serves as the source of diffusing atoms. After the diffusion run the needle is removed and the surface is scanned with a shielded counting arrangement. The diffusion profiles reported in this paper were obtained by a modification of the above procedure which employs a precision ARG technique. Previous investigations in this laboratory and elsewhere51B have shown that under carefully controlled developing conditions and by the use of calibration sources a linear relation exists between the concentration of the isotope and the photographic density for values below unity. The use of ARG under these conditions has advantages over the counter scanning method in that cumbersome shielding and requirements for great mechanical precision of the scanner are eliminated. Also the ARG gives a complete picture of the surface which is advantageous in studies of anisotropic diffusion. A recording microdensitometer having a 0.1 p wide slit was employed. At low temperatures the disturbing effects of subsurface radiations are negligible. The diffusion anneals are carried out in the cell shown in Fig. 1. The needle is formed by grinding down a 1.0 mm rod of high-purity silver until a tip of 0.2 mm radius or smaller is formed. This tip is plated withA"&apos; which becomes the source of the diffusing atoms that are detected by ARG. The needle carrier and the crystal holder, Fig. 1 are constructed of quartz and ports are provided in the holder pedestal which allow free vapor circulation ((2.0 oz) and the carrier apron fits snugly over the crystal holder cap, insuring that the needle does not move and scratch the surface. Temperatures are provided by a stabilized tubular furnace which can be quickly positioned around the cell, thus bringing the crystal up to temperature in a time that is short compared to the diffusing times. The diffusion anneals range from 2 hr for the high-temperature samples to about 25 hr for those at the lowest temperature. The possibility of vapor transport of the radioactive metal as a contributing factor in the diffusion profile was investigated in two ways. One method was to suspend the needle directly over a dummy sample, raise the temperature, for periods of time equal to the diffusion times, and then take an auto-radiograph of the surface. Negligible radioactivity appeared. In the second method a thin slot in the crystal face on one side of the source provided a "cong path" for surface diffusion. If evaporation was the primary source of surface atoms the region of radioactivity around the source would be symmetrical. This was not the case. The profile dipped abruptly at the edge of the slot but on the other side of the source the usual diffusion profile appeared.

Jan 1, 1963

By David White

THE search for potash salts in the great "Red Beds? region of the Southwest, conducted for several years by the U. S. Geological Survey, the work being carried on for a part of the time in coöperation with the Bureau of Economic Geology and Technology of the University of Texas, has resulted in the discovery, within shafting depth, of potash salts, apparently of workable thickness and commercial quality, and prob-ably of great extent. Definite information is lacking as to the exact thickness of the potash beds, the size and boundaries of the areas underlain by workable strata, and the locations of the deposits richest and most favorably situated for exploitation. Briefly to review the salient features, of the general situation: We have in the great Red Beds region of the southwestern United States, embracing portions of central Kansas, western Oklahoma, eastern New Mexico, and northern and western Texas, .a series of sandstones. shales, anhydrite beds, clays and limestones, which; through an interval of 1000 ft., more or less, carry beds of salt, estimated by Darton1 to contain over 30,000 billions of tons of rock salt. It is the greatest known salt field of the world. At some points the intercalated beds of rock salt, one of which is reported by the driller to exceed 300 ft. in thickness, aggregate, accord-ing to the drillers&apos; records, over 1000 ft. The sedi-mentary strata are similar in composition to those carrying the potash deposits of western Europe, and they were laid down at the same time and under condi-tions which, in many respects at least, were similar The stratigraphy and character of the beds are des-cribed by Darton2 and a, part of the area and the reported aggregate thicknesses of salt are shown, with some revision after Darton, in the accompanying map Fig. 1. The assumption that in the great areas of shallow evaporation basins spread over -the vast base-level region of saline deposition in the Southwest during Permo-Triassic time, potash salts were in some places, and at different stages, thrown down in crystalline deposits associated with the beds of rock salt, anhydrite, and gypsum, is, geologically speaking, more than reason-able. They are to be expected, and the conviction that they are probably present has long been held both in the Texas Bureau of Economic Geology and Tech-nology, under Dr. J. A. Udden, and in the- U. S. Geological Survey. Accordingly, for many years, efforts to determine whether potash deposits are present in this region have been made, though under very great difficulties, such as insufficient funds for boring, hack of drilling on private initiative in the more promising regions, hack of interest at first on the part of the drillers and companies, and, hater, inadequacy both of the methods of boring and of the sampling, to reveal in definite terms the thickness-of any saline stratum of given composition.

Jan 4, 1922

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller&apos;s earths fall within the general group of bleaching clays and gradually the commercial term "fuller&apos;s earth" has been applied to natural clays originating, for the most part, in the south-eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.1 Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). TABLE 1.-Physical and Chemical Composition of Different Types of Clays Composition, Per Cent Constituents and Properties Bentonite Fuller&apos;s Mud Clay (Wyoming) Earth (P Peak)&apos; (Alluvial) Silica (SiO2) 60.0 69.6 61.67 Alumina (Al203) 19.0 14.3 20.34 Ferric oxide (Fe203) 2.8 3.90 7.70 Titanium oxide (Ti02) 0.13 0.70 1.01 Lime (CaO) 0.5 0.80 0.00 Magnesia (MgO) 2.0 1.00 0.24 Soda (Na2O) 2.4 0.40 0.31 Ignition loss 4.7 6.77 8.51 Moisture content 8.0 10.0 20.0 Isoelectric point, pH 9.2 9.2 6.5 Average swelling volume 15.0 0.0 0.0 Weight per cubic foot, lb 55.0 40.0 65.0 Material passing 200-mesh sieve, per cent 90.0 85.0 50.0

Jan 1, 1939

By T. E. Scott, R. P. Zerwekh

The charactevistics of the deformatiotz of fcc thorium were examined between 78 and 473 K. Activation energy, actiuation volume, and the temperature dependence of the flow stress were determined and conlpared uith several theories for the rate-controlling mechnnistn of the tempemture-dependent component of the flou~ stress. It was established that the Cottrell-Stokes law does not hold, even approximately, for thorium. Through consideration of the above factors and other parameters, it was concluded that the vandom solute barrier theory proposed by Friedel demonstrates the best agreement with experimental observations of the deformation of thorium below ambient temperature. THORIUM, the first metal in the actinide series of rare-earth elements, is interesting and important from two points of view. In the more practical vein, it is a potential reactor fuel. As such, it is important to know its properties. Of specific interest here are the mechanical properties of thorium. Second, no detailed information concerning the deformation characteristics of the actinide elements has been gathered to date. In view of the interesting physical and chemical properties of these metals, their mechanical behavior might reveal characteristics which could improve our understanding of the mechanisms controlling deformation of the more common metals. For example, it has been shown1 that thorium exhibits a yield point which is greatly enhanced by interstitial solute elements such as carbon. This is not a normal occurrence in fcc metals. The goal of this investigation, therefore, was to characterize the deformation of polycrystalline thorium. MATERIAL AND PROCEDURES Thorium, made by the magnesium intermediate alloy process described by Peterson et al.,2 was rolled and swaged to 0.065-in.-diam wire. The metal analysis is given in Table I. After preparation, the oxygen and nitrogen contents had risen to 308 and 60 ppm, respectively. The 0.065-in.-diam wires were cut into 2-in. lengths and annealed in a vacuum of lo-&apos; Torr at 750°C for 1 hr, producing a grain size of 2735 grains per sq mm. The ends of the 2-in. sections were masked off so that a 1-in. gage length could be electropolished. Specimens were polished at 35 v in a solution of 6 pct perchloric acid in methanol which was maintained at 0°C . The gage diameters after polishing were about 0.0625 in. The tests were run on a screw-driven tensile machine at a constant crosshead speed corresponding to a strain rate of 0.005 min-&apos;. The strain rate was changed rapidly after each 0.01-in. extension between 0.005 min-&apos; and one of three higher strain rates which were selected in order to achieve strain-rate ratios of 5, 10, and 20. Tests were run at several temperatures from 78" to 473°K; most were tested at 423", 300°, 215", and 78°K. EXPERIMENTAL RESULTS Flow Stress vs Strain and Temperature. Typical true stress-true strain curves for thorium are shown in Fig. 1 for several temperatures over the range 473" to 78°K. The curves for 78", 215", 300") and 423°K were obtained from strain-rate change tests using the lower (0.005 min-&apos;) or base strain-rate values of stress. Additional tests, using the same base strain rate at different strain-rate ratios, gave curves which virtually superposed on those shown, indicating that strain-rate changes did not materially influence the work-hardening characteristics at the base strain rate. The curves for 273") 373") and 473°K were standard tensile tests at 0.005 min-&apos;. The behavior of the flow stress with temperature is

Jan 1, 1968