Search Documents

By F. Weinberg

INTEREST is currently being directed toward grain boundary morphologies in zinc in terms of grain boundary facetingl and grain boundary energies.' Some years ago the present author attempted to measure grain boundary energies in 99.999 pct purity Zn as a function of boundary angle, using the standard procedure of measuring equilibrium angles of the boundary traces at triple points. This followed an investigation he carried out on preferential melting of |H (112) Fig. 1—Electron transmission micrograph of a stacking fault, grain boundary intersection in copper. GRAIN BOUNDARY STACKING FAULT Fig. 2—Schematic representation of the intersection of Fig. 1, indicating inclination angles 0 and trace angles $. specimens were prepared by the Bollman technique in an electrolyte of 70 pct methanol, 30 pct HNO3 main-tained at -30°C. The interfacial free energy of the high angle grain boundary and of the stacking fault is assumed to be thermodynamically equivalent to the corresponding in-terfacial tensions. In terms of the true dihedral angles & between the intersecting interfaces, the equilibrium of interfacial tensions in the direction parallel to the stacking fault yields: ysF = -ygb(cos F1+ cos ±cosF2) Here, ysF is the stacking fault free energy and ygb is the grain boundary free energy, assumed equal on both sides of the intersection. Forces acting normal to the grain boundary, of the form ??gb/?F,l are assumed negligible as the grain boundary remains straight for a considerable distance on either side of the intersection. The micrograph of Fig. 1 may actually consist of several closely spaced stacking faults on the same slip plane. The actual point of intersection between the grain boundary and the first stacking fault, and the equilibrium configuration of the intersection, should not be affected by the presence of the other faults, as

Jan 1, 1970

By Rodolfo V. de la Cruz

The in situ deformability of rock masses is determined by relating the applied load to the radial displacements of points on the borehole wall that are outside of the loaded surfaces. The external displacement method includes the steps in which: a) radial displacement sensors are installed to measure the change in length of a diameter of a borehole; b) unidirectional self- equilibrating pair of forces perpendicular to the direction of radial displacement measurements are applied on opposite sectors of the borehole wall, and; c) using elastic theory, the in-situ deformability of the rock mass can be related with the applied loads and measured radial displacements. The displacements outside the loaded surfaces are comparatively smaller in magnitude than displacements inside the loaded surfaces. These displacements, however, are sufficiently large and can be measured precisely by commercially available linear displacement sensors. Loads are applied by a conventional borehole jack. Existing methods for measuring the in situ deformability of rock masses yields unreliable results due to complex boundary stresses, small and varying contact areas, and the existence of fractures. It was shown that in the external displacement method, the effect of boundary pressure distribution and contact area are negligible. Also, since the displacements measured in the external displacement method were due to materials that are deeper inside the rock mass, borehole fractures have less influence on the calculated deformation modulus.

Jan 1, 1982

By Murl R., Schrock

THE use of diamond-drill holes at the Moctezuma Copper Co., Pilares mine, Pilares de Nacozari, Sonora, Mexico, for the ventilation of raises has resulted from experiments that were made in an effort to secure continuous and efficient ventilation in hot and gaseous raises. The method is particularly applicable in long raises and in raises run from development levels where the source of fresh air is distant. In order that the CO, concentration shall not become excessive, 30 cu. ft. per min. per man must be supplied to a heading for breathing purposes:' The quantity of air that will pass through a diamond-drill hole by

Jan 1, 1929

By D. Geoffry Minnes, Ray Blair, Stanley J. LeFond

Nepheline syenite is a silica deficient crystal-line rock consisting of albite and microcline feldspars and nepheline, together with varying but small amounts of mafic silicates and other accessory minerals. Nepheline-bearing rocks are widely distributed around the world but only in Canada, Norway, the Union of Soviet Socialist Republics, and the United States are deposits worked commercially, Because of its low melting point and fluxing ability, nepheline syenite was investigated in the early 1900s by many students of glass and ceramics. Although the nepheline syenite deposits in Methuen Township, Ont., Canada, were discovered as early as 1897 it wasn't until 1935 that the first mill was erected to produce nepheline syenite products. In Canada, nepheline syenite deposits are worked by Indusmin Ltd. and International Minerals and Chemical Corp. (Canada) Ltd. who have combined production capacity in excess of 1800 stpd. Between 1935 and 1972 seven million tons valued at $78 million were produced from the Methuen Township deposits. In Norway, the Norsk Nefelin Div. of Elkem Spigerverket has produced nepheline syenite from a deposit on Stjernöy Island in western Finland since early 1960. Production has increased from 8 kt in 1961 to over 200 kt in 1980. Nepheline syenite has been under investigation in the Union of Soviet Socialist Republics (USSR) since at least 1928. In 1951 the first commercial alumina works was brought on stream at Volkhov, near Leningrad, utilizing nepheline concentrates from the Kola peninsula as mill feed. Since then two others have been completed and more are planned. Large quantities of portland cement, sodium carbonate, and potassium carbonate are produced in conjunction with the alumina. A material called nepheline syenite, but actually a pulaskite, is produced in Pulaski County, Arkansas, by the McGeorge Construction Co. for construction aggregates and by the 3M Co. for roofing granules. The Dome Fill Co. purchases the fines and uses them in the preparation of enclosed construction fill. Production is over 2,000,000 stpy. Chap. 16 on "Feldspar, Nepheline Syenite, and Aplite" in the 3rd ed. of Industrial Minerals and Rocks (Castle and Gillson, 1960) and Nepheline Syenite Deposits of Southern Ontario (Hewitt, 1960) contain excellent accounts of earlier commercial development of nepheline syenite as a glass and ceramic material. As in the 4th ed., this chapter deals mostly with the period since 1960 and with matters not previously reported in detail. An English monograph on Nepheline-Syenite and Phonolite (Allen et al., 1968) is a complete survey, at the time, of nepheline syenite which, with its very complete list of references, is an excellent source book. End Uses Nepheline syenite from the Canadian and Norwegian producers finds use primarily in the manufacture of glass and ceramics. One producer also makes several grades of nephellne syenite that are useful as extender pigments and fillers in paint, plastics, and rubber. In the Soviet Union nepheline is used in increasing quantities in the manufacture of alumina, alkali carbonates, and portland cement and to a lesser degree it is used in the manufacture of colored container glass.

Jan 1, 1983

By C. Scala, M. Gondouin

Published laboratory data have established that very significant streaming potentials can exist across mud cakes subjected to pressure differentials such as exist between a mud column and formation fluids. Since shale is similar in kind and in properties to a well-formed mud cake, it appeared possible that streaming potentials might also arise across shales. A practical consequence would be that the streaming potential contribution to the SP would be smaller than might otherwise be assumed since the SP is measured with respect to the "shale bare line". The resultant contribution would be the difference between the streaming potential across the shale and that across the mud cake. In order to investigate this possibility, a laboratory apparatus was devised for measuring streaming potentials under pressure conditions normally encountered in wells. Reported data on streaming potentids across mud cakes were verified. More important, appreciable streaming potentials were found across shale samples. As in the case of mud cakes, the shale potentials varied with the concentration and nature of the impregnating electrolyte. Dependence on pressure was In a different rela-tion than that for mud cakes, possibly because of the lower compressibility of shales. The differences in streaming potentials between the shales md mud cakes were generally small, although they might vary considerably in practice depending on the relative electro-kinetic properties of the particular shale-mud cuke combination. A "poorly eflective" shale with a "very eflec-tive mud cake" would produce the largest negative addition to the electrochemical component of the SP. Results of field experiments with pressurized wells were considered in the light of the laboratory results. INTRODUCTION Field experiments wherein the pressure of the mud column in a borehole was varied have often indicated the presence of a streaming potential, but its magnitude was not easily predictable and its sign sometimes changed from one formation to another in the same well.' In the interpretation of SP logs from standard surveys, nevertheless, the correct value of R,, is very frequently obtained, within the limits of field accuracy, using only the simple electrochemical expression of the SP provided that proper corrections are made for bed thickness, ion activity, etc.' Accordingly, it was apparent that the streaming potential component of the SP in a borehole was considerably more complex than commonly assumed and clarification was indeed necessary The close similarity in nature and constitution of a shale to a well-compacted mud cake suggested that a streaming potential might also exist across shales as pointed out by M. P. Tixier in 1953 and as recently emphasized by Wyllie." e practical consequence would be that the streaming potential across the mud cake would be canceled, at least in part, on electrical logs since the SP is recorded with respect to the shale potential as a base line. This appeared to be a plausible explanation for many of the effects observed but no supporting data were available. In 1955 preliminary experiments at low pressures were conducted in our laboratories which supported the hypothesis of the shale streaming potential and formed the basis for later studies at borehole pressures.* EARLY LOW PRESSURE EXPERIMENTS The early experiments were conducted primarily to determine the possibility of a streaming potential across shales. The shale used was a compact type designated as No. 7 from Reagan County, Tex. (Permian). Cut samples were saturated for over one month in .2 to 2.0-N NaCl solutions. In order to eliminate all electrode polarization effects, a dynamic method was used. A transient pressure of about 1 atm was applied across

By I. R. Kramer

The stress associated with the surface layer was deter-minedfor iron and molybdcnum. These measurements show that the surface layer plays a very important role in the plastic deformation of bcc metals. From the relationship between strain arui the surface layer stress and the back stress imposed by the internal obstacles, it is Proposed that the term of of the Hall-Petch equation is related only THE large number of studies on plastic flow of bcc metals have failed to delineate clearly the nature of the obstacles influencing dislocation movement. Since there have been numerous articles which have reviewed the mechanisms proposed to explain various aspects of plastic flow of bcc metals (for example, conrad1 and Keh and weissmann2), no attempt will be made here to discuss their conclusions. However, it should be to the surface stress while the term Kfd is the stress required to move dislocations through internal obstacles. Further, it was possible to derive the well-known empirical equation C = , and it is shown that the terprz a is comprised of two terms: a term Cs associated with the surface layer stress and Ci related to internal dislocation obstacles. pointed out that in all of these publications it has been tacitly assumed that plastic flow occurred uniformly throughout the cross section of the specimen (except, of course, for the Luders band region), It has generally been further assumed that the nature and distribution of the obstacles opposing the motion of dislocations are of the same type throughout. The role of the surface layer in bcc metals has not, as yet, been considered even though its role in fcc metals has been shown clearly to be of primary importance.3-5 Investigations on fcc metals have shown that at the onset of plastic deformation a surface layer acts to

Jan 1, 1968

By Frederick Laist

THE object of the construction and operation of the 80-ton leaching plant was to test out the leaching of sand tailings on a large scale and, if possible, determine a definite method of operation, and the best construction for the larger unit which is now being built. It was also of importance to obtain some practical data as regards cost items. The 80-ton plant was not expected to be a commercial success. A leaching process on such low-grade material necessitates the treatment of a very large tonnage.. Such a cost item as labor, for instance, is entirely out of proportion in such a small plant. The amounts of acid, salt, scrap iron, and fuel for roasting, however, are the same per ton in an 80-ton plant as in a 2,000-ton plant. These costs were definitely established. Also the percentages of extraction and grade of tailings were definitely determined for a large-sized unit. Following will be found the description of the plant, the method of operation and the results obtained. A -general view of the plant is given in Fig. 1. The bins consisted of one coal bin with a capacity of 30 tons, one salt bin with a capacity of 20 tons, and a "mill tailings" or feed bin which held 70 tons. The coal and salt bins were placed with their floor level even with the firing floor of the roasting furnace. The feed bin, to give it greater capacity, discharged about 12 ft. below this point, to a 12-in. conveyor belt, which, in turn discharged into a pug mill. This fed another conveyor belt, which discharged into the top hearth of the furnace. The furnace was an ordinary six-hearth MacDougall roaster, .20-ft. in diameter. It was equipped with two fire boxes, on opposite sides, the flames entering on the third hearth. An induced draft was obtained with a Buffalo blower, worked as an exhaust fan. Just above the top hearth was an annular flue around the whole circumference of the furnace. Slots at intervals of about 18 in. led from this flue down into the top hearth. The slots were 2 in. wide by 6 in. long. This annular flue proved rather unsatisfactory, as it tended to fill up with flue dust and choke the slots, thus cutting down the draft. The volume of gas through

Jan 8, 1914

By Richard E. McElvain

The mining and other industries have grown and changed with- respect to their requirements for slurry pumps capable of handling high percentages of abrasive materials. Greater solids concentration, higher heads and pressures, and increased flow arc not possible. Today's equipment delivers up to three times the flow-tonnage and 1.3 times the head per stage as compared with pumps of ten years ago. This results in four times the requirement in size and energy. The new centrifugal pumps are capable of handling these requirements at pressures up to 4826 kPa (700 psi), with 6895 kPa (1000 psi) or more being considered for future systems. The latest pumps, functioning at four times the operating requirement on flow-head, weight eight times more than the previous equipment. Efficiency is increased slightly, to about 75 % to 85%. A testing program on equivalent units has confirmed that the added strength and specific design of heavy-duty pumps can meet demanding engineering objectives. Operating life on difficult-to-pump materials is increased from 500 to over 5000 hours of continuous operation; the ten-fold increase in pump operating time is a major design objective.

Jan 12, 1976

By Claude H. P. Lupis, John F. Elliott

WAGNERL described the thermodynamic behavior of a metallic solution consisting of the solute components 2, 3,... at very dilute concentrations in the solvent, 1, in terms of the excess partial molar free energy, or alternatively the logarithm of the activity coefficient. In the Taylor expansion of FiE, by neglecting the second- and higher-order differential terms, he obtained the excess partial molar free energy as a linear function of the composition:

Jan 1, 1965

By George Krauss, Seth R. Thomas

One complete cycle, allstenite to martensite to aus-tenite, of Martensitic transformation was induced in a commercial 18 Cr-8 Ni stainless steel. Transmission electron microscopy showed that the reverse transfarmation, martensite to austenite, perpetuated the dense defect substructure of the martensite produced by the direct transformation, austenite to 'martensite, and reproduced the retained austenite matrix orientation. A general precipitation of lathlike M,,C, particles was noted to be present in, and is suggested as cause for, regions of martensite that Izad formed after a complete cycle of transformation. The habit plane of the precipitate particles was found to be within 5 a plane previously established as the habit of nitride precipitates of similar morphology in bcc iron. The direct transformation of austenite (y) to martensite (a) in metastable 300 series stainless steels has received considerable attention in the past,'-8 and the martensite product given special emphasis in recent years,9"*u but little information has been published about the reverse martensitic transformation during which bcc a martensite is converted to fcc y austenite."-" The reversal mechanism and the resulting crystallographic relationship between parent and product austenite are of fundamental concern. The reversal product, fully austenitic, and hereafter referred to as reversed austenite, exhibits a defect structure far different from its virgin counterpart. Some studies have been reported in which the structure of reversed austenite in iron nickel alloys is compared to annealed austenite with respect to austenite strengtheningM and Stabilization.' The martensite in these Fe-Ni alloys, however, shows a basic difference from that produced in stainless steels. Structurally, the Fe-Ni martensite is profusely twinned," while the (low-carbon) Fe-Cr-Ni martensite contains a high density of tangled dislocations and is apparently twin-free.I0 reediis" has recently shown in an Fe-16 Cr-12 Ni stainless alloy that this typical martensitic defect structure and the reverse transformation directly influence the structure of the reversal product. He found that much of the reversed austenite had returned to the orientation of the virgin austenite and that fine twins were formed in the austenite after the reverse transformation. This investigation was undertaken in order to describe as completely as possible the structural changes produced by a cycle of transformation in a typical 18-8 stainless steel. EXPERIMENTAL PROCEDURE The 301 stainless steel under investigation (17.44 Cr, 7.75 Ni, 0.80 Mn, 0.60 Si, 0.40 Mo, 0.40 Cu, 0.08 C, 0.03 N, bal Fe)was received as 0.060-in.-thick

Jan 1, 1968

By J. H. Smith, H. W. Paxton

ALTHOUGH many structural and kinetic investigations have been made for alloys of iron and nickel, only meager data exist from thermodynamic investigations. The purpose of this note is to estimate the free energy of the Fe-Ni solid solutions from thermodynamic data available for ternary alloys containing iron and nickel. The lack of a description of the thermodynamic behavior for the Fe-Ni system has required the structural and kinetic analyses of the system to assume some form of solution behavior, usually regular, e.g., the mar-tensite transformation analysis of Kaufman and Cohen, 1 consistent with the limited thermodynamic data. Indications that this system could exhibit ideal solution departures might have been suggested by the large deviations from additivity rules observed in the density and lattice-parameter measurements of Jette and Foote2 who interpreted this in terms of possible solute-solvent interactions. Later Turkdogan et al. 3 and more recently Ward and wright 4 found a minimum in the graphite solubility in liquid Fe-Ni solutions near the concentration of FeNi3 with deviations from linearity persisting at all concentrations. This was interpreted by Ward and wright4 to indicate negative heats of solution and was suggestive of short-range ordering. The infinitely dilute activity coefficient of carbon (?oC) was also observed by smith5 to pass through a maximum near the FeNi3 concentration in Fe-Ni solid solutions. Recent investigations of the liquid solutions over the entire concentration range by Zellars et a1.' and Speiser et a1.," using vapor-pressure determinations, revealed both negative departures from Raoult's law and a nonregular solution behavior. The solid alloys have been studied by Oriani 8 and Kubaschew-ski and von Goldbeck6 employing gaseous H2/H2O equilibria with Fe and FeO. Both investigations were in substantial agreement, indicating very small departures from ideality. However, Oriani observed the formation of Fe3O4 (instead of FeO) at XFe= 0.441 which severed the equilibrium and precluded experimental investigation of the nickel-rich alloys. Heat-capacity and heat-content measurements have been evaluated by Montgomery10 and found generally unsatisfactory for gleaning thermodynamic information. This is due to the unknown final states of the alloys caused by the interference of the martensite transformation on cooling iron-rich concentrations and superlattice formation, magnetic transformation, and the varied heat treatments used by investigators of nickel-rich concentrations. As an alternative to the experimental difficulties, indirect estimates of the solid-solution behavior have been made by Fleischer and Elliott11 and Smith et a1.12 From their measurements of the solubility of Fe-Ni alloys in liquid lead, Fleischer and Elliott calculated the nickel activity (aNi) (and integrated for aFe) by assuming: 1) liquid lead has no solubility in solid Fe-Ni alloys, 2) Henry's law is obeyed throughout the liquid lead-rich phase (0— 12 at. pct Nil, and 3) Henry's law constant is independent of relative iron and nickel concentrations. The estimate of Smith et a1.12 was obtained

Jan 1, 1964

By J. D. Rice, P. L. Wearden, W. L. Hensou

Solutions to the unsteady-state partial water-drive reservoir performance problem can be obtained through the use of analogue computers or high-speed electronic digital computers. The solutions that have previously been resolved for use on digital computers, however, demand a knowledge of the aquifer parameters. Generally, the analogue computers now in use do not require this knowledge. A solution is presented herein where the aquifer performance, expressed in terms of difference equations, is related to the reservoir performance as expressed by the modified Scbiltbuis material-balance equation. A numerical procedure for a medium-sized digital computer also is presented in which a solution to the set of equations defining the aquifer and reservoir performance is obtained and the aquifer parameters (permeability and sand thickness) are automatically optimized while simultaneously matching the known pressure behavior. Predicted pressure behavior can be calculated using rates from any assumed future production practice. The procedure provides an output format which presents the cumulative, incremental and average rate of natural water influx, the per cent gas-cap expansion, the calculated reservoir pressure, the measured reservoir pressure, and the difference between the measured and calculated pressures. Results of a test problem are presented in comparison with results obtained by the Bruce Analyzer, Ohio Oil Co. 's Pace General Purpose Analogue Computer, and Sun Oil Co.'s Single-Pool Electronic Reservoir Analyzer. These results indicate that unsteady-state reservoir perlormance for a single-pool system can be adequately simulated by a numerical method employing a digital computer and that the special-purpose analogue computer can be supplanted by this method. INTRODUCTION The numerical approach to the unsteady-state partial water-drive reservoir performance problem heretofore has been limited in that solutions have been resolved only for certain fixed parameters. Also, prior to the advent of high-speed electronic digital computers in the last few years, calculations were so tedious and time-consuming that they ordinarily were neglected, or some other means of obtaining the solutions were used. The analogue approach had been used for obtaining solutions to the transmission-of-heat problem and, consequently, means were developed for applying the electrical analogue to the unsteady-state reservoir performance problem. Bruce submitted a paper for AIME publication in Sept. 1942, in which he described an electronic device (now called the Bruce Analyzer) for analyzing the water-drive performance of any reservoir, based on either steady or unsteady-state flow characteristics. 1 Sun Oil Co. adopted the analogue approach in 1949 and now has two special-purpose high-speed electronic reservoir analyzers in use.2,3 Two main features of Sun's analyzers are (1) the high repetitive rate of reproducing the entire history of reservoir performance cyclically a number of times per second, and (2) the elimination of the necessity of knowing the properties of the associated aquifer. Since the advent of larger and faster digital computers, the possibility of incorporating this second feature into a numerical approach appeared feasible. Previous work has been done and material published covering the application of numerical methods to the behavior of the pressure with respect to time at any point in an associated aquifer? However, the aquifer parameters must be known from some source. The material presented in Ref. 4 has been used to a great degree in developing the numerical method described herein. DIFFERENTIAL EQUATION AND BOUNDARY CONDITIONS The problem of simulating the performance of a reservoir and the associated aquifer is to determine the characteristics of the aquifer such that the

By T. Watanabe, S. Karashima, H. Oikawa

Creep tests of a! iron and its solid-solution Fe-Mo, Fe-Co, and Fe-Si alloys with bcc structure were conducted under constant stresses in ferromagnetic and paramagnetic temperature regions above 0.5T,(T, is the absolute melting temperature). It was found their high-temperature creep behavior changed in the vicinity of the magnetic transformation temperature, that is Curie temperature, TC. In the ferromagnetic region below the steady-state creep rates were lower than those expected from the extrapolation of the data in the paramagnetic region, the amount of decrease being affected by solute addition. Also, activation energies for steady-state creep were different in the two temperature regions. The observed changes were concluded to be due to the effect of ferromagnetism on diffusion. It is well-known that plastic deformation of metals and alloys in the temperature region where mobility of atoms becomes high enough is controlled by atomic diffusion." Many experimental results394 on fcc and hcp materials have been reported to confirm this view. In bcc metals and alloys, not much basic investigation of creep deformation has been performed. In particular, experimental work on iron5-&apos; and its alloys, covering a quite wide temperature range is extremely scarce. On the other hand, the effect of ferromagnetism on diffusion has recently been demonstrated in a iron and its alloys;&apos; it has been made clear that diffusion rates in ferromagnetic temperatur~e region are significantly lower than those expected from diffusion measurement in the paramagnetic region. Therefore, it is concluded that the magnetic effect influences the high-temperature creep behavior in a! iron and in its alloys. The present authors have conducted creep experiments on a iron and its solid-solution alloys over a very wide temperature range, and have demonstrated the magnetic effect. A part of the result has already been reported elsewhere.26 In this paper, the experimental results will be described in detail. While the manuscript was in preparation, a similar magnetic effect on creep deformation of a iron was reported by Ishida . Though their experiments covered an extremely wide temperature range, the creep stresses varied from several thousand psi to several ten thousand psi with decreasing temperature. Consequently, it may be said that there remain some questions concerning their results. I) EXPERIMENTAL PROCEDURE The materials used in the experiments were pure iron and its alloys; they were prepared by vacuum melting (10"" mm Hg) electrolytic iron (99.9 pct), molybdenum powder (99.9 pct), ultrapure silicon, and cobalt pellet (99.5 pct) in alumina crucibles. The ingots were hot-forged to plates 10 mm thick and 50 mm wide, and then were hot-rolled at about 700°C into sheets 1 mm thick. Creep specimens, 5 mm in width and 15 mm in gage length, were machined from the sheets. They were annealed at temperatures which were well above their respective recrystallization temperatures. The chemical compositions of the metal and alloys are shown in Table I together with their heat treatments. High-temperature creep tests by the use of a lever-type creep testing machine were carried out in argon atmosphere under constant tensile stress. In order to keep &eep stress constant within about *0.5 pct, stress change due to specimen elongation was compensated by tensile force of a stainless-steel bellows which was inserted between the loading lever and lower specimen grip with the assumptions of a linear relationship between change in cross section and strain and uniform strain along the section. Beyond the limit of compensation by the bellows, small amounts of load were removed after appropriate strains. The testing temperatures were maintained to within i2"C of the reported values. Creep deformation was auto-graphically recorded at the upper (moving) specimen grip using a linear differential transformer which was held by a stainless-steel rod mechanically connected to the lower specimen grip. It was also directly measured with a dial-gage reading to -& mm. 11) EXPERIMENTAL RESULTS AND DISCUSSION 1) Creep Curves of a Iron and Its Alloys. Creep curves of a! iron, Fe-Si, Fe-Co, and Fe-Mo (<2 at. pct Mo) alloys usually consisted of three stages, that is transient (primary), steady-state (secondary), and accelerating (tertiary) stages. An example is illustrated in Fig. 1 for a! iron. However, in Fe-Mo alloys with more than 2 at. pct Mo, an inverse transient creepZ8 was observed as indicated in Fig. 2. The inverse behavior, which varied with the amount of molybdenum, may be due to the substructure* in the annealed specimen as was sug-

Jan 1, 1969

By O. Katz, A. Spilners, M. Simnad

THE oxidation of titanium has been studied in recent years by a number of investigators.&apos;-W ne of the most important aspects of the reaction of titanium with oxygen, which has been observed by several of the investigators, is the extremely high solubility of oxygen in the metal. A detailed study of the Ti-0 systeml% as shown that the solubility limit of oxygen in a-titanium is approximately 14.5 wt pct 0 from 800" to 1700°C. The unusual oxidation behavior of titanium may be ascribed to this phenomenon, since part of the oxygen uptake enters into solid solution in the metal and only a part is available for scale formation. A more complete study of the kinetics of oxidation of titanium would require information on the influence of oxygen in solution in the metal upon the oxidation rate. Such information would also be of interest in regard to the theory of oxidation of metals. The authors have measured the oxidation rates of oxygen-saturated and oxygen-free titanium between 800" and 1200°C and have found appreciable differences in their rates of oxygen uptake and in the activation energies. The experimental set-up was similar to that described in a previous paper.u The course of oxida-dation was followed continously by attaching the specimen to a sensitive spring balance and observing the extension of the spring with time of oxidation. High purity electrolytic oxygen was used and precautions were taken to purify the gases employed. The specimens were prepared from iodide titanium and were ground on metallographic polishing papers to a fineness of 4/0. The furnace was first evacuated and filled with argon; the specimen was lowered into the furnace, which was then evacuated and filled with oxygen, after the specimen had reached the oxidation temperature in argon. The samples were presaturated with oxygen by means of the following procedure: Each specimen was first heated in oxygen at 1200°C until its increase in weight indicated 13.8 pct by weight uptake of oxygen. The furnace was then immediately evacuated and filled with purified argon five times. The specimen was heated in the argon atmosphere for a period of 72 hr at 1200°C in order to saturate the metal with oxygen by complete absorption of the scale. The temperature was lowered to the oxidation temperature, the furnace was evacuated and filled with oxygen, and the oxidation rate was followed by noting the extension of the spring balance. No oxide film was visible on these specimens at the start of the oxidation experiments. Titanium samples in the oxygen-free as-received condition were also oxidized and their oxidation rates measured. The results are shown in Figs. 1, 2, and 3, which indicate that the initial rates of uptake of oxygen by both the oxygen-saturated and oxygen-free specimens are parabolic at these temperatures. The rate of uptake of oxygen is, however, appreciably lower

Jan 1, 1956

By C. H. Cheng, C. E. Birchenall

The fundamental problem in the thermodynamics of solid solutions is the determinatiorl or calculation of the activities of the components as a function of temperature and composition. Since the theory of metals is not suficiently developed to allow a priori calculation of these quantities, they must be obtained from experiment. C. Wagner1 has reviewed the literature of this subject for the period before 1940. Although several important and extensive studies have been made in the meantime, the number of systems to which any sort of quantitative information can be assigned is vanish-ingly small. These data have become of great potential importance in studies of the structure of solid solutions2 and intermetallic compounds, the nature of the diffusion process,3,4 and perhaps even the mechanism of mechanical deformation.5 For these reasons, it. seems very worthwhile to extend the experimental data in this field. Although there is little use in duplicating Wagner&apos;s review, attention should be directed to the most recently reported investigations. A brief enumeration of the methods of measurement previously employed also should be valuable. The most direct method is the determination of the partial pressure of the components in the vapor phase in equilibrium with the solution. Both equilibrium and kinetic methods have been tried in metal systems, but almost exclusively on liquid phases. Only in the ease of carbon in iron alloys and in the copper-zinc system have extensive measure- ments been made which include solid phases. When one of the components is an element, such as nitrogen or carbon, which forms compounds which are very volatile and stable at normal temperatures and pressures (CH4, Co2, CO NH3), it is frequently possible to equilibrate mixtures containing these (such as CH4-H2, CO2-CO, NH3-H2) independently with the elernents (C, X) and with the metal (Fe, Ni, etc.). Such measurernents have been made for carbon in iron, iron-silicon, and iron-manganese alloys by Smith6 and in iron and iron-nickel alloys by Toensing.7 Differences between carbon activity values at the same temperature and carbon content when carboil is introduced from CH4-H2 rnixtures or CO-CO. mixtures indicate that the effects of hydrogen and oxygen in the system are not negligible, and one can only hope that the true value lies somewhere between these sets of results, probably nearer the CH4-H2 data since hydrogen is less soluble in iron than oxygen. This is essentially an equilibrium method, although flowing gas is employed. A kirletic method has been employed which consists of sweeping an inert gas (generally hydrogen) over the alloy at a series of rates, condensing the metal vapor out,, and analyzing it. The metal content can be extrapolated to zero flow rate (equilibrium). Wejnarth&apos;s8 work on Cd-Mg and Zn-Mg is a good example of this frequently used method. A variant of this consists of equilibrating a known volume of inert gas with the alloy, sweeping it out quickly, and analyzing for metal. In common with the above method, it has the disadvantage that the "inert" gas is generally somewhat soluble in the alloy. Moreover, the former continuously displaces the system from equilihrium and may give low values if solid diffusion is involved. The dew point method applied by Hargreaves9 to the alpha and beta brasses and by Schneider and Stolll0 to A1-Zn avoids the introduction of another component to the system, but is useful only in systems in which one component is much more volatile than the other. The alloy sealed in one end of an evacuated silica tube is heated to the desired temperature. The temperature of the other end is lowered until droplets of the volatile component condense. When the temperature is raised slightly, the droplets will evaporate. By careful adjustment of temperature, the range between evaporation and condensation can be narrowed appreciably. An independent determination of the vapor pressure of the . pure volatile component is necessary to give the partial pressure over the alloy. This is the method employed here to determine the vapor pressures of zinc and cadmium over their silver alloys up to 34 pct in cadmium and 76 pct in zinc. The former involves only the a solid solution, but the latter covers the a, ß, y, and e fields. In recent determinations, Herbenar, Siebert, and Duffenbarkl1 used the

Jan 1, 1950

By J. R. Long, A. H. Roberson, T. R. Graham, R. S. Dean

Experimental work on the properties of high-purity alloys of the copper-man-ganese-zinc system has necessarily required extensive metallographic work to determine the equilibrium conditions in this system. Previous work on these alloys is fragmentary and, unfortunately, based on alloys made with impure grades of manganese, thus introducing significant amounts of iron, silicon, aluminum and carbon. Since these elements are known to affect equilibrium conditions, it became desirable to re-examine these alloys made from the pure metals. The alpha solid solution field was of particular interest and, therefore, was chosen for the initial work, which was outlined to determine the composition limits of this field. Previous Work Heuslerl conducted an extensive survey of the liquid-solid regions of this system and also made an estimate of the solid-phase boundaries at 340°C. The pertinent part of his diagram is given in Fig. I, but it is of limited usefulness, since it applied to a single temperature only and is based on impure alloys under admittedly nonequilib- rium conditions. Bauer and Hansen,2 likewise working with impure alloys, have determined the phase boundaries for alpha-beta brasses containing small amounts of manganese and indicate an increase in the extent of the alpha field with increasing manganese. This is not in accordance with Heusler or with data obtained on pure alloys.3 They also described a third constituent precipitating in the alpha plus beta field below 350&apos; to 400°C. but did not identify this constituent. Guillet4 and Heike and Ledibur6 have also noted this precipitate. Each of these investigators recognized that impurities present in the manganese could and did have an effect on the structure and properties of their alloys. Corson6 in particular pointed out the hardening effects of silicon, aluminum, and carbon in copper-manganese alloys and Heusler reported that his alloys containing more than 25 per cent manganese were extremely brittle. In all probability this brittleness was due to the impurities present. This early work, therefore, should be taken as a general guide for preliminary studies only, and high-purity alloys may be expected to produce different results. The work of the Bureau of Mines laboratories with electrolytic manganese has been briefly summarized by Dean7 but includes only a short section on this system. Later work3 outlined a limited portion of the alpha field in the neighborhood of 65 per cent copper, 10 per cent manganese, and 25 per cent zinc. The present work was under-

Jan 1, 1945

[NORTH AMERICA UNITED STATES ALABAMA Birmingham CORD, Richard H DISMUKES, Edward B Citronelle PERRIN, Huey P Fairfield PAGEL, Herbert Ervin Huntsville ENG, Harvard KELLEY, Dean W WAGGONER, J B Mobile HORNER, William L PETROUTSON, Peter C Montgomery GAMBLE, Halbert R Redstone RAWLINGS, William E Tuscaloosa MASON, William L University CUDWORTH, James R JONES, Walter B]

Jan 1, 1961

By J. S. Lasater

Resu1ts of experinmental measurernents of heat capacities and thermal conductivities of some typical porous rocks are presented. Measured heat capacities agree closely with va1ues calculated front known chenlical . compositions of the rocks. On the basis of this agreement, heat capacitir.7 of fluid-satttrated rocks were calc~ililted. Therrnal conductivities of the rock samples were measured under varioits conditions of fluid saturation. From these data therrnal dif-fvsivities were calculated. A significant variation of thermal diflusivity with trnlperature is indicated. Knowledge of the thermal characteristics of fluid-bearing porous rocks has become increasingly important with the development of thermal oil-recovery processes. Reliable thermal data for petroleum reservoir rocks are not available and approximate values are generally assumed for reservoir calculations. &apos;The effects of temperature, pressure and fluid saturation on thermal properties of porous rocks have not been carefully studied. The purpose of the present work was to measure and report the thermal characteristics of some typical porous rocks. A group of eight sedimentary rock samples, including limestone, shale, sandstone and silt-stone, was selected for the study. Properties reported include heat capacities, thermal conductivities and thermal diffusivities. The effect of fluid saturation on these properties was also considered. Determinations of thermal properties require precise measurements which are time consuming and difficult to reduce to a routine basis. Methods have not been developed for measurement of thermal proper-ties under conditions of pressure, temperature, and fluid saturation, which may be encountered in thermal recovery processes. As one approach to these problems, some preliminary work on methods of estimating thermal properties from other more readily measurable characteristics of the rock-fluid system is reported. The samples selected for the studies were oilfield cores from within, or closely associated with oil-productive zones. Descriptions of individual samples are given in Table 1. Clay minerals present in the samples were determined by differential thermal analysis (DTA). Quartz content was estimated from DTA cooling curves. For all but the thermal conductivity tests, a representative 200-gm sample of each core was disaggregated, thoroughly extracted in diox-ane and oven dried at 100°C. The cleaned and dried sample was care- fully split into appropriate portions for the several tests. Chemical analyses of the samples were obtained to permit calculations of heat capacities by methods which are outlined later. Resuits of chenlical analyses are given in Table 2. Heat contents of the test samples were measured by a Runsen-type calorimeter. The heat content of the unknown sample is measured relative to the known heat content of platinum. The apparatus is referred to as a relative error type because of the comparative measurements, and has the advantage of canceling systematic errors. Experimental results are reproducible within 0.5 per cent. A temperature base of 298.16 K is taken for heat content measurements. Measurements were made at five temperatures (260, 440, 620, 800 and 980° F). It was necessary to preheal the sample above the maximum experimental temperature to eliminate volatile constituents. Assuming the weight loss on pre-heat, ing was mostly water, a correction to the observed heat content was made to account for the water originally present in the sample. This latter procedure was followed in the determination of calculated heat contents as will be described later. The apparatus and the method of measure-

Major William R. Grunow, in a brief account off his military services, says: "I take pleasure in informing you that since my return from France I have been stationed at Camp A. A. Humphreys, Va., and am now on duty as a Senior Instructor at the Engineer Officers&apos; Training School. While in France, I served as a company commander in the 305th Engineers and was later ordered to return to the United States for assignment to new troops. Upon arrival in the United States, I received my majority." P. F. Rodegerdts gives us the following account of his military service: "I enlisted in the Naval Reserve Flying Corps in San Francisco on Feb. 12, 1918. On February 10, I was ordered to Cambridge, Mass., where I was enrolled for the course in technical aircraft construction given at Massachusetts Institute of Technology. After successfully completing the course of instruction, I spent six weeks in practical construction of seaplanes at the Curtiss aeroplane factory in Buffalo. Following this, I was assigned to active service at Akron, Ohio, on June 22, 1918. At the same time I received my commission of ensign U.S.N. R.F. Unfortunately, I have been kept at Akron and although I have made

Jan 1, 1919

By C. S. Smith, E. W. Palmer

For several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 † except for the electrical conductivity at 200" C., which is given in the appendix of this paper. Literature on Thermal Conductivity of Copper Alloys The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey&apos;s determinations4 were carried out on the alloys used by Lees6 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the material. It is equally to be regretted that neither Hanson and Rogers nor Bailey give data for the electrical conductivities of their samples. Sager6, using the heat-wave method of King, determined the thermal conductivity of copper, nickel and four alloys of the two metals. His results are included in Table 1.

Jan 1, 1935